Cisco ASR 9000 Series Aggregation Services Router L2VPN and Ethernet Services Command Reference, Release 5.1.x
Point to Point Layer 2 Services Commands
Downloads: This chapterpdf (PDF - 1.97MB) The complete bookPDF (PDF - 5.11MB) | Feedback

Point to Point Layer 2 Services Commands

Contents

Point to Point Layer 2 Services Commands

This module describes the commands used to configure, monitor, and troubleshoot a Layer 2 or Layer 3 virtual private network (VPN).

For detailed information about virtual private network concepts, configuration tasks, and examples, refer to the Cisco ASR 9000 Series Aggregation Services Router L2VPN and Ethernet Services Configuration Guide.

backup (L2VPN)

To configure the backup pseudowire for the cross-connect, use the backup command in L2VPN xconnect p2p pseudowire configuration mode. To disable this feature, use the no form of this command.

backup neighbor IP-address pw-id value

no backup neighbor IP-address pw-id value

Syntax Description

neighbor IP-address

Specifies the peer to cross connect. The IP-address argument is the IPv4 address of the peer.

pw-id value

Configures the pseudowire ID. The range is from 1 to 4294967295.

Command Default

None

Command Modes

L2VPN xconnect p2p pseudowire configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the backup command to enter L2VPN xconnect p2p pseudowire backup configuration mode.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to configure backup pseudowires:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group gr1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p p001
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor 10.1.1.1 pw-id 2
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# backup neighbor 10.2.2.2 pw-id 5
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw-backup)#

Related Commands

Command

Description

backup disable (L2VPN)

Specifies how long a backup pseudowire should wait before resuming operation after the primary pseudowire goes down.  

l2vpn

Enters L2VPN configuration mode.  

neighbor (L2VPN)

Configures a pseudowire for a cross-connect.  

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

xconnect group

Configures cross-connect groups.  

backup disable (L2VPN)

To specify how long a backup pseudowire should wait before resuming primary pseudowire operation after the failure with primary pseudowire has been cleared, use the backup disable command in L2VPN pseudowire class configuration mode. To disable this feature, use the no form of this command.

backup disable { delay value | never }

no backup disable { delay value | never }

Syntax Description

delay value

Specifies the number of seconds that elapse after the failure with primary pseudowire has been cleared before the Cisco IOS XR software attempts to activate the primary pseudowire.

The range, in seconds, is from 0 to 180. The default is 0.

never

Specifies that the secondary pseudowire does not fall back to the primary pseudowire if the primary pseudowire becomes available again, unless the secondary pseudowire fails.

Command Default

The default disable delay is the value of 0, which means that the primary pseudowire is activated immediately when it comes back up.

Command Modes

L2VPN pseudowire class configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how a backup delay is configured for point-to-point pseudowire in which the backup disable delay is set to 50 seconds:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class class1
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# backup disable delay 50
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group A
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrx
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor 10.1.1.1 pw-id 2
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# pw-class class1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# backup neighbor 10.2.2.2 pw-id 5
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw-backup)#

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

neighbor (L2VPN)

Configures a pseudowire for a cross-connect.  

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

xconnect group

Configures cross-connect groups.  

clear l2vpn collaborators

To clear the state change counters for L2VPN collaborators, use the clear l2vpn collaborators command in EXEC mode.

clear l2vpn collaborators

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to clear change counters for L2VPN collaborators:

RP/0/RSP0/CPU0:router# clear l2vpn collaborators

Related Commands

Command

Description

show l2vpn collaborators

Displays information about the state of the interprocess communications connections between l2vpn_mgr and other processes.  

clear l2vpn counters bridge mac-withdrawal

To clear the MAC withdrawal statistics for the counters of the bridge domain, use the clear l2vpn counters bridge mac-withdrawal command in EXEC mode.

clear l2vpn counters bridge mac-withdrawal { all | group group-name bd-name bd-name | neighbor ip-address pw-id value }

Syntax Description

all

Clears the MAC withdrawal statistics over all the bridges.

group group-name

Clears the MAC withdrawal statistics over the specified group.

bd-name bd-name

Clears the MAC withdrawal statistics over the specified bridge.

neighbor ip-address

Clears the MAC withdrawal statistics over the specified neighbor.

pw-id value

Clears the MAC withdrawal statistics over the specified pseudowire. The range is from 1 to 4294967295.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to clear the MAC withdrawal statistics over all the bridges:

RP/0/RSP0/CPU0:router# clear l2vpn counters bridge mac-withdrawal all

clear l2vpn forwarding counters

To clear L2VPN forwarding counters, use the clear l2vpn forwarding counters command in EXEC mode.

clear l2vpn forwarding counters

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to clear L2VPN forwarding counters:

RP/0/RSP0/CPU0:router# clear l2vpn forwarding counters

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

clear l2vpn forwarding counters bridge-domain mirp-lite

To clear L2VPN forwarding MIRP counters, use the clear l2vpn forwarding counters bridge-domain mirp-lite command in EXEC mode.

clear l2vpn forwarding counters bridge-domain mirp-lite { location node-id }

Syntax Description

location node-id

Clears the L2VPN forwarding MIRP counters for the specified location.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read, write, execute

Examples

This example shows how to clear all the MIRP counters:
RP/0/RSP0/CPU0:router# clear l2vpn forwarding counters bridge-domain mirp-lite location 0/1/CPU0

This example shows how to clear bridge-domain specific MIRP counters:
RP/0/RSP0/CPU0:router# clear l2vpn forwarding counters bridge-domain bg1:bd1 mirp-lite location 0/1/CPU0

Related Commands

Command

Description

clear l2vpn forwarding counters

Clears L2VPN forwarding counters.  

clear l2vpn forwarding message counters

To clear L2VPN forwarding message counters, use the clear l2vpn forwarding message counters command in EXEC mode.

clear l2vpn forwarding message counters location node-id

Syntax Description

location node-id

Clears L2VPN forwarding message counters for the specified location.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to clear L2VPN forwarding message counters on a specified node:

RP/0/RSP0/CPU0:router# clear l2vpn forwarding message counters location 0/6/CPU0

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

clear l2vpn forwarding table

To clear an L2VPN forwarding table at a specified location, use the clear l2vpn forwarding table command in EXEC mode.

clear l2vpn forwarding table location node-id

Syntax Description

location node-id

Clears L2VPN forwarding tables for the specified location.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to clear an L2VPN forwarding table from a specified location:

RP/0/RSP0/CPU0:router# clear l2vpn forwarding table location 1/2/3/5

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

control-word

To enable control word for MPLS encapsulation, use the control-word command in L2VPN pseudowire class encapsulation submode. To disable the control word, use the no form of this command.

control-word

no control-word

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation configuration

Command History

Release

Modification

Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to enable control word for MPLS encapsulation:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class pwc1 
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)# control-word

dynamic-arp-inspection

To validate Address Resolution Protocol (ARP) packets in a network, use the dynamic-arp-inspection command in the l2vpn bridge group bridge domain configuration mode. To disable dynamic ARP inspection, use the no form of this command.

dynamic-arp-inspection { logging | address-validation { src-mac | dst-mac | ipv4 } }

no dynamic-arp-inspection { logging | address-validation { src-mac | dst-mac | ipv4 } }

Syntax Description

logging

(Optional) Enables logging.

Note   

When you use the logging option, the log messages indicate the interface on which the violation has occured along with the IP or MAC source of the violation traffic. The log messages are rate limited at 1 message per 10 seconds.

Caution   

Not all the violation events are recorded in the syslog.

address-validation

(Optional) Performs address-validation.

src-mac

Source MAC address in the Ethernet header.

dst-mac

Destination MAC address in the Ethernet header.

ipv4

IP addresses in the ARP body.

Command Default

Dynamic ARP inspection is disabled.

Command Modes

l2vpn bridge group bridge domain configuration

Command History

Release

Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to enable dynamic ARP inspection on bridge bar:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group b1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# dynamic-arp-inspection 
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-dai)#

This example shows how to enable dynamic ARP inspection logging on bridge bar:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group b1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# dynamic-arp-inspection logging
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-dai)#

This example shows how to enable dynamic ARP inspection address validation on bridge bar:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group b1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# dynamic-arp-inspection address-validation
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-dai)#

Related Commands

Command

Description

bridge-domain (VPLS)

Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.  

bridge group (VPLS)

Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.  

l2vpn

Enters L2VPN configuration mode.  

flood mode

To change the flood mode from Bandwidth Optimized to Convergence Optimized, use the flood mode convergence-optimized command in the l2vpn bridge group bridge domain configuration mode. To return the bridge to normal flooding behavior (when all unknown unicast, broadcast and multicast packets are flooded over other bridge domain network interfaces), use the no form of this command.

flood mode { resilience-optimized | convergence-optimized }

no flood mode { resilience-optimized | convergence-optimized }

Syntax Description

resilience-optimized

Configures bridge to use Resilience Optimized mode.

convergence-optimized

Configures bridge to use Convergence Optimized mode.

Command Default

The bridge domain operates in the Bandwidth Optimized Mode.

Command Modes

l2vpn bridge group bridge domain configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The flood mode command allows you to change the flood optimization mode to either Convergence Optimized mode or Resilience Optimized mode. The Convergence Optimized mode floods all traffic to all line cards; all unknown unicast packets, all broadcast packets, and all multicast packets are flooded over all other bridge domain network interfaces. The Resilience Optimized Mode works like Bandwidth Optimized mode, except that it floods traffic to both primary and backup FRR links for a Pseudowire.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to clear an L2VPN forwarding table from a specified location:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group MyGroup
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain MyDomain
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# flood mode convergence-optimized
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)#

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

bridge-domain (VPLS)

Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.  

bridge group (VPLS)

Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.  

generic-interface-list

To configure generic interface list, use the generic-interface-list command in global configuration mode.

generic-interface-list list-name

Syntax Description

list-name

Name of the interface list.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification
Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to configure generic interface list:

RP/0/RSP0/CPU0:router# config
RP/0/RSP0/CPU0:router(config)# generic-interface-list interfacelist1
RP/0/RSP0/CPU0:router(config-if-list)# interface GigabitEthernet 0/2/0/1
RP/0/RSP0/CPU0:router(config-if-list)# interface GigabitEthernet 0/3/0/1
RP/0/RSP0/CPU0:router(config-if-list)# exit

Related Commands

Command

Description

show l2vpn generic-interface-list

Displays all the L2VPN virtual interfaces.  

interface (p2p)

To configure an attachment circuit, use the interface command in p2p configuration submode. To return to the default behavior, use the no form of this command.

interface type interface-path-id [ PW-Ether | PW-IW]

no interface type interface-path-id [ PW-Ether | PW-IW]

Syntax Description

type

Interface type. For more information, use the question mark (?) online help function.

interface-path-id

Physical interface or a virtual interface.

Note   

Use the show interfaces command to see a list of all possible interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (?) online help function.

PW-Ether

(Optional) Configures an Ethernet Interface.

PW-IW

(Optional) Configures an IP Interworking Interface.

Command Default

None

Command Modes

p2p configuration submode

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.2.1

The following keywords were added:

  • PW-Ether
  • PW-IW

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to configure an attachment circuit on a TenGigE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group gr1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p p001
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# interface TenGigE 1/1/1/1

Related Commands

Command

Description

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

interworking ipv4

To configure IPv4 interworking, use the interworking ipv4 command in the p2p configuration submode. To return to the default behavior, use the no form of this command.

interworking ipv4

no interworking ipv4

Syntax Description

ipv4

Sets IPv4 interworking.

Command Default

None

Command Modes

p2p configuration submode

Command History

Release

Modification

Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to configure an attachment circuit on a TenGigE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group gr1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p gr1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# interworking ipv4
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)#

Related Commands

Command

Description

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

ipv4 source

To configure source IP address for the pseudowire class with encapsulation mpls, use the ipv4 source command in the L2VPN pseudowire class encapsulation mpls configuration mode.

ipv4 source source-ip-address

Syntax Description

source-ip-address

Source IP address.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation mpls configuration

Command History

Release Modification
Release 4.2.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to configure the source ip address:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)#l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)#pw-class kant1
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)#encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)#ipv4 source 112.22.1.4

Related Commands

Command

Description

pw-class encapsulation mpls

Configures MPLS pseudowire encapsulation.  

l2tp static

To enable the Layer 2 Tunneling Protocol (L2TP) static submode, and perform L2TP pseudowire configurations, use the l2tp static command in p2p pseudowire configuration submode. To disable the L2TP static submode, use the no form of this command.

l2tp static [ local { cookie { secondary size | size } { 0 | 4 | 8 } value value | session session id } | remote { cookie size { 0 | 4 | 8 } value value | session session id } ]

no l2tp static [ local { cookie { secondary size | size } { 0 | 4 | 8 } value cookie value | session session id } | remote { cookie size { 0 | 4 | 8 } value cookie value | session session id } ]

Syntax Description

local

(Optional) Configures local cookies and sessions.

cookie

Sets L2TP pseudowire static local or remote cookie.

secondary size

Sets L2TP pseudowire static local cookie secondary size.

size

Sets L2TP pseudowire static local cookie size.

value

Sets the value of the cookie.

cookie value

Value of the cookie.

The cookie values are specified based on the configured cookie size:

  • Cookie size 0—No cookie value is set.
  • Cookie size 4—Lower 4 bytes value (<0x0-0xffffffff>) is set.
  • Cookie size 8—Lower 4 bytes value and higher 4 bytes values (<0x0-0xffffffff> <0x0-0xffffffff> ) are set.
session

Sets L2TP pseudowire static local or remote session.

session id

Session ID. Range is from 1 to 65535.

remote

(Optional) Configures remote cookies and sessions.

Command Default

None

Command Modes

p2p pseudowire configuration

Command History

Release Modification
Release 4.3.1

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to enter the l2tp static configuration sub mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static

This example shows how to configure local and remote session-id:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static local session 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote session 1

This example shows how to configure cookie size and values:

This example is with cookie size 0:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie size 0
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote cookie size 0

This example is with cookie size 4:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie size 4 value <0x0-0xffffffff>
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote cookie size 4 value <0x0-0xffffffff>

This example is with cookie size 8 (lower 4 bytes entered first and then higher 4 bytes):

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie size 8 value <0x0-0xffffffff> <0x0-0xffffffff>
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote cookie size 8 value <0x0-0xffffffff> <0x0-0xffffffff>

This example show how to configure a secondary local cookie:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie secondary size 8 value <0x0-0xffffffff> <0x0-0xffffffff>

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

xconnect group

Configures cross-connect groups.  

neighbor (L2VPN)

Configures a pseudowire for a cross-connect.  

ip-source-guard

To enable source IP address filtering on a layer 2 port, use the ip-source-guard command in l2vpn bridge group bridge domain configuration mode. To disable source IP address filtering, use the no form of this command.

ip-source-guard logging

no ip-source-guard logging

Syntax Description

logging

(Optional) Enables logging.

Command Default

IP Source Guard is disabled.

Command Modes

l2vpn bridge group bridge domain configuration

Command History

Release

Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to enable ip source guard on bridge bar:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group b1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# ip-source-guard
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-ipsg)#

This example shows how to enable ip source guard logging on bridge bar:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group b1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# ip-source-guard logging
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd-ipsg)#

Related Commands

Command

Description

bridge-domain (VPLS)

Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.  

bridge group (VPLS)

Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.  

l2vpn

Enters L2VPN configuration mode.  

l2transport

To configure a physical interface to operate in Layer 2 transport mode, use the l2transport command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport

no l2transport

This command has no arguments or keywords.

Command Default

None

Command Modes

Interface configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The l2transport command and these configuration items are mutually exclusive:

  • IPv4 address and feature (for example, ACL) configuration
  • IPv4 enable, address and feature (for example, ACL) configuration
  • Bundle-enabling configuration
  • L3 subinterfaces
  • Layer 3 QoS Policy

Note


After an interface or connection is set to Layer 2 switched, commands such as ipv4 address are not usable. If you configure routing commands on the interface, l2transport is rejected.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to configure an interface or connection as Layer 2 switched under several different modes:

Ethernet Port Mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RSP0/CPU0:router(config-if)# l2transport

Ethernet VLAN Mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.900 l2transport
RP/0/RSP0/CPU0:router(config-if)# encapsulation dot1q 100do1q vlan 999

Ethernet VLAN Mode (QinQ):

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.900 l2transport
RP/0/RSP0/CPU0:router(config-if)# encapsulation dot1q 20 second-dot1q 10vlan 999 888

Ethernet VLAN Mode (QinAny):

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.900 l2transport
RP/0/RSP0/CPU0:router(config-if)# encapsulation dot1q 30 second-dot1q do1q vlan 999 any

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

l2transport l2protocol

To configure Layer 2 protocol handling, use the l2transport l2protocol command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport l2protocol cpsv { reverse-tunnel | tunnel }

no l2transport l2protocol cpsv { reverse-tunnel | tunnel }

Syntax Description

cpsv

Enables L2PT for the interface. L2PT is enabled for the following protocols only:

  • CDP
  • STP
  • VTP
Note   

STP includes all Spanning Tree protocol derivatives (RSTP, MSTP, etc.)

tunnel

Performs L2PT encapsulation on frames as they enter the interface. Also, performs L2PT de-encapsulation on frames as they exit they interface.

L2PT encapsulation rewrites the destination MAC address with the L2PT destination MAC address. L2PT deencapsulation replaces the L2PT destination MAC address with the original destination MAC address.

reverse-tunnel

Performs L2PT encapsulation on frames as they exit the interface. Also, perform L2PT deencapsulation on frames as they enter the interface.

Command Default

None

Command Modes

Interface configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

These L2 protocols are available:

  • Cisco Discovery Protocol (CDP)—CDP is protocol-independent and is used to obtain protocol addresses, platform information, and other data about neighboring devices.
  • PVST maintains a spanning tree instance for each VLAN configured in the network and permits a VLAN trunk to be forwarding for some VLANs and not for others. It can also load balance Layer 2 traffic by forwarding some VLANs on one trunk and other VLANs n others.
  • Spanning-Tree Protocol (STP)—STP is a link management protocol that provides path redundancy in the network. For Ethernet networks to function properly, only one active path can exist between two stations.
  • VLAN Trunk Protocol (VTP)—VTP is a Cisco-proprietary protocol that reduces administration in a switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain.

Task ID

Task ID

Operations

l2vpn

read, write

atm

read, write

Examples

The following example shows how to configure Layer 2 protocol handling:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RSP0/CPU0:router(config-if)# l2transport l2protocol cpsv reverse-tunnelstp drop

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

l2transport propagate

To propagate Layer 2 transport events, use the l2transport propagate command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport propagate remote-status

no l2transport propagate remote-status

Syntax Description

remote-status

Propagates remote link status changes.

Command Default

None

Command Modes

Interface configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The l2transport propagate command provides a mechanism for the detection and propagation of remote link failure for port mode EoMPLS.

To display the state of l2transport events, use the show controller internal command in Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Configuration Guide

For more information about the Ethernet remote port shutdown feature, see Cisco ASR 9000 Series Aggregation Services Router MPLS Configuration Guide.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to propagate remote link status changes:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RSP0/CPU0:router(config-if)# l2transport propagate remote remote-status

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

l2transport service-policy

To configure a Layer 2 transport quality of service (QoS) policy, use the l2transport service-policy command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport service-policy { input policy-name | output policy-name }

no l2transport service-policy { input policy-name | output policy-name }

Syntax Description

input policy-name

Configures the direction of service policy application: input.

output policy-name

Configures the direction of service policy application: output.

Command Default

None

Command Modes

Interface configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

atm

read, write

Examples

The following example shows how configure an L2 transport quality of service (QoS) policy:

RP/0/RSP0RP00/CPU0:router# configure
RP/0/RSP0RP00/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RSP0RP00/CPU0:router(config-if)# l2transport service-policy input sp_0001

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

l2vpn

To enter L2VPN configuration mode, use the l2vpn command in global configuration mode. To return to the default behavior, use the no form of this command.

l2vpn

no l2vpn

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Global configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configuration can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to enter L2VPN configuration mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)#

Related Commands

Command

Description

show l2vpn forwarding

Displays forwarding information from the layer2_fib manager on the line card.  

load-balancing flow

To enable all bundle EFPs and PW to use either L2 flow based or L3 flow based balancing, use the load-balancing flow command in L2VPN configuration mode.

load-balancing flow [ src-dst-mac | src-dst-ip ]

Syntax Description

src-dst-mac

Enables global flow load balancing hashed on source and destination MAC addresses.

src-dst-ip

Enables global flow load balancing hashed on source and destination IP addresses.

Command Default

None

Command Modes

L2VPN configuration

Command History

Release

Modification

Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to set the bridge ID:

RP/0/RSP0/CPU0:router# configure 
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# load-balancing flow src-dst-ip

load-balancing flow-label

To balance the load based on flow-labels, use the load-balancing flow label command in l2vpn pseudowire class mpls configuration mode. To undo flow-label based load-balancing, use the no form of this command.

load-balancing flow-label { both | code | receive | transmit } [ static ]

no load-balancing flow-label { both | code | receive | transmit } [ static ]

Syntax Description

both

Inserts or discards flow labels on transmit or receive.

code

Specifies the flow label TLV (type-length-value) code. The code value is 17.

receive

Discards flow label on receive.

transmit

Inserts flow label on transmit.

static

Sets flow label parameters statically.

Command Default

None

Command Modes

L2vpn pseudowire class mpls configuration mode

Command History

Release Modification
Release 4.2.1

This command was introduced.

Release 4.3.2

The code keyword was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

In the draft-ietf-pwe3-fat-pw document, the flow label sub-TLV identifier for the Flow Aware Transport Pseudowire (FAT PW) was 0x11. This value has been changed to 0x17, which is also the sub-TLV identifier assigned by the Internet Assigned Numbers Authority (IANA).

Use the load-balancing flow label code command to toggle between the sub-TLV identifiers—0x11 and 0x17. If there is a mismatch between two endpoints in the load-balancing flow label code, then the PWs will have a mismatched TLV value resulting in a loadbalancing failure.

The no form of the load-balancing flow label code command uses the flow label sub-TLV identifier 0x11.

Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows the output of the load-balancing flow-label command of the both keyword.

RP/0/RSP0/CPU0:router#config
RP/0/RSP0/CPU0:router(config)#l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)#pw-class p1
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)#encapsulation
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)#encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing flow-label
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing flow-label both
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing flow-label both static

Related Commands

Command

Description

pw-class encapsulation mpls

Configures MPLS pseudowire encapsulation.  

load-balancing pw-label

To enable all pseudowires using the defined class to use virtual circuit based load balancing, use the load-balancing pw-label command in pseudowire class configuration mode.

load-balancing pw-label

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Pseudowire class configuration

Command History

Release

Modification

Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to set the bridge ID:

RP/0/RSP0/CPU0:router# configure 
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class abc
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-mpls)# load-balancing pw-label

logging (l2vpn)

To enable cross-connect logging, use the logging command in L2VPN configuration submode. To return to the default behavior, use the no form of this command.

logging pseudowire status

no logging pseudowire status

Syntax Description

pseudowire status

Enables pseudowire state change logging.

Command Default

None

Command Modes

L2VPN configuration submode

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configuration can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to enable cross-connect logging:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# logging pseudowire status

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

logging nsr

To enable non-stop routing logging, use the logging nsr command in L2VPN configuration submode. To return to the default behavior, use the no form of this command.

logging nsr

no logging nsr

Syntax Description

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN configuration submode

Command History

Release Modification
Release 4.3.0

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configuration can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to enable non-stop routing logging:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# logging nsr

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

monitor-session (l2vpn)

To attach a traffic monitoring session as one of the segments for a cross connect, use the monitor-session command in point-to-point cross connect configuration mode. To remove the association between a traffic mirroring session and a cross connect, use the no form of this command.

monitor-session session-name

no monitor-session session-name

Syntax Description

session-name

Name of the monitor session to configure.

Command Default

No default behavior or values

Command Modes

Point-to-point cross connect configuration

Command History

Release

Modification

Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Before you can attach a traffic mirroring session to a cross connect, you must define it using the monitor-session global configuration command. Once the traffic mirroring session is defined, use the monitor-session point-to-point cross connect configuration command to attach this session as one of the segments for the cross connect. Once attached, all traffic replicated from the monitored interfaces (in other words, interfaces that are associated with the monitor-session) is replicated to the pseudowire that is attached to the other segment of the cross-connect.

The session-name argument should be different than any interface names currently used in the system.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to attach a traffic mirroring session as segment for the xconnect:

RP/0/RSP0/CPU0:router(config)# l2vpn 
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group g1 
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p xcon1 
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# monitor-session mon1 
   

This example shows how an EFP is associated to a monitor session:

RP/0/RSP0/CPU0:router(config)# interface Gi0/0/0/4.2 l2transport 
RP/0/RSP0/CPU0:router(config-subif)# monitor-session customer-foo 
 

This example shows how L2 SPAN is supported on L3 interfaces, but the whole L2 frame is mirrored:

RP/0/RSP0/CPU0:router(config)# interface Gi0/0/0/4.2 l2transport 
RP/0/RSP0/CPU0:router(config-subif)# ipv6 address 1111:3333::cdef
RP/0/RSP0/CPU0:router(config-subif)# monitor-session customer-foo 
 

This example shows how SPAN is also supported on main interfaces:

RP/0/RSP0/CPU0:router(config)# interface Gi0/0/0/4.2 l2transport 
RP/0/RSP0/CPU0:router(config-subif)# l2transport
RP/0/RSP0/CPU0:router(config-subif)# monitor-session customer-foo 
 

This example shows creation of xconnect between the monitor-session and a L2TPv3 over IPv6 tunnel:

RP/0/RSP0/CPU0:router(config)# l2vpn 
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group span 
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p span-foo 
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# monitor-session customer-foo
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor ipv6 1111:3333::cdef pw-id 1001 
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# pw-class ts
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# source 1111:3333::abcd
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# l2tp static local cookie size 8 value 0xabcd 0x1234
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# l2tp static remote cookie size 8 value 0xcdef 0x5678

Related Commands

Command

Description

monitor-session

Defines a traffic mirroring session and enter monitor session configuration mode.  

mpls static label (L2VPN)

To configure static labels for MPLS L2VPN, use the mpls static label command in L2VPN cross-connect P2P pseudowire configuration mode. To have MPLS assign a label dynamically, use the no form of this command.

mpls static label local label remote value

no mpls static label local label remote value

Syntax Description

local label

Configures a local pseudowire label. Range is 16 to 15999.

remote value

Configures a remote pseudowire label. Range is 16 to 15999.

Command Default

The default behavior is a dynamic label assignment.

Command Modes

L2VPN cross-connect P2P pseudowire configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to configure static labels for MPLS L2VPN:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.2 pw-id 1000
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# mpls static label local 800 remote 500

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

neighbor (L2VPN)

Configures a pseudowire for a cross-connect.  

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

xconnect group

Configures cross-connect groups.  

neighbor (L2VPN)

To configure a pseudowire for a cross-connect, use the neighbor command in p2p configuration submode. To return to the default behavior, use the no form of this command.

neighbor { A.B.C.D | ipv4 ipv4 address | ipv6 ipv6 address } pw-id value [ backup | l2tp static | mpls | | pw-class | source ipv6 address | tag-impose ]

no neighbor { A.B.C.D | ipv4 ipv4 address | ipv6 ipv6 address } pw-id value [ backup | l2tp static | mpls | | pw-class | source ipv6 address | tag-impose ]

Syntax Description

A.B.C.D

IP address of the cross-connect peer.

ipv4 ipv4 address

Assigns the IPv4 address of the cross-connect peer.

ipv6 ipv6 address

Assigns the IPv6 address of the cross-connect peer.

pw-id value

Configures the pseudowire ID and ID value. Range is 1 to 4294967295.

backup

(Optional) Specifies the backup pseudowire for the cross-connect.

l2tp static

(Optional) Configures the L2TP pseudowire static

mpls

(Optional) Configures an MPLS static label.

pw-class

(Optional) Configures the pseudowire class template name to use for this cross-connect.

source ipv6 address

(Optional) Specifies the source IPv6 address of the pseudowire. This option is available only for the IPv6 neighbor.

tag-impose

(Optional) Specifies a tag during a VLAN ID configuration

Command Default

None

Command Modes

p2p configuration submode

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.2.1

The keyword tag-impose was introduced.

Release 4.3.1

The following keywords were added:

  • ipv4
  • ipv6
  • l2tp static
  • source

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

A cross-connect may have two segments:

  1. An Attachment Circuit (AC)
  2. An second AC or a pseudowire

Note


The pseudowire is identified by two keys: neighbor and pseudowire ID. There may be multiple pseudowires going to the same neighbor. It is not possible to configure only a neighbor.


All L2VPN configurations can be deleted using the no l2vpn command.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows a point-to-point cross-connect configuration (including pseudowire configuration):

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.2 pw-id 1000 pw-class class12
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.3 pw-id 1001 pw-class class13
RP/0/RSP0/CPU0:router(config-xc)# p2p rtrC_to_rtrD
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 10.2.2.3 pw-id 200 pw-class class23
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 10.2.2.4 pw-id 201 pw-class class24

This example shows a point-to-point cross-connect configuration (including pseudowire configuration):

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.2 pw-id 1000 pw-class foo
RP/0/RSP0/CPU0:router(config-xc)# p2p rtrC_to_rtrD
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor 20.2.2.3 pw-id 200 pw-class bar1

This example shows a point-to-point IPv6 cross-connect configuration:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1

This example shows how to set a source IPv6 address to a point-to-point IPv6 cross-connect :

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-xc-p2p-pw)# source 1111:2222::abcd

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

xconnect group

Configures cross-connect groups.  

nsr (L2VPN)

To configure non-stop routing, use the nsr command in L2VPN configuration submode. To return to the default behavior, use the no form of this command.

nsr

no nsr

Syntax Description

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN configuration submode

Command History

Release Modification
Release 4.3.0

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configuration can be deleted using the no l2vpn command.


Task ID

Task ID Operation

l2vpn

read, write

Examples

The following example shows how to configure non-stop routing:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# nsr

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

preferred-path

To configure an MPLS TE tunnel to be used for L2VPN traffic, use the preferred-path command in Encapsulation MPLS configuration mode. To delete the preferred-path, use the no form of this command.

preferred-path interface { tunnel-ip | tunnel-te | tunnel-tp } value [ fallback disable ]

no preferred-path interface { tunnel-ip | tunnel-te | tunnel-tp } value [ fallback disable ]

Syntax Description

interface

Interface for the preferred path.

tunnel-ip

IP tunnel interface name for the preferred path.

value

Tunnel number for preferred path.

fallback disable

(Optional) Disables fallback for preferred path tunnel settings.

tunnel te

Specifies the TE tunnel interface name for the preferred path.

tunnel tp

Specifies the TP tunnel interface name for the preferred path.

Command Default

None

Command Modes

Encapsulation MPLS configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.2.0

The keyword tunnel-tp was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The preferred-path command is applicable only to pseudowires with MPLS encapsulation.

Use the show l2vpn xconnect detail command to show the status of fallback (that is, enabled or disabled).


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to configure preferred-path tunnel settings:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-tp 345 
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-tp 345 fallback disable

Related Commands

Command

Description

show l2vpn xconnect

Displays brief information on configured cross-connects.  

protocol l2tpv3

To configure Layer 2 Tunneling Protocol Version 3 (L2TPv3) as the signaling protocol for a pseudowire class, use the protocol l2tpv3 command in L2VPN pseudowire class encapsulation L2TPv3 configuration mode. To disable L2TPv3 as the signaling protocol for a pseudowire class, use the no form of this command.

protocol l2tpv3 [ class class_name ]

no protocol l2tpv3 [ class class_name ]

Syntax Description

class

Specifies the L2TPv3 class.

class_name

The L2TPv3 class name.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation L2TPv3 configuration

Command History

Release Modification
Release 4.3.1

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to set the encapsulation and protocol to L2TPv3:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

pw-class encapsulation l2tpv3

Configures L2TPv3 pseudowire encapsulation.  

pw-class (L2VPN)

To enter pseudowire class submode to define a pseudowire class template, use the pw-class command in L2VPN configuration submode. To delete the pseudowire class, use the no form of this command.

pw-class class-name

no pw-class class-name

Syntax Description

class-name

Pseudowire class name.

Command Default

None

Command Modes

L2VPN configuration submode

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to define a simple pseudowire class template:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group l1vpn
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor 10.1.1.2 pw-id 1000
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# pw-class kanata01

Related Commands

Command

Description

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

pw-class encapsulation l2tpv3

To configure L2TPv3 pseudowire encapsulation, use the pw-class encapsulation l2tpv3 command in L2VPN pseudowire class configuration mode. To return to the default behavior, use the no form of this command.

pw-class class name encapsulation l2tpv3 [ cookie size { 0 | 4 | 8 } | dfbit set | ipv4 source address | pmtu max 68-65535 | protocol l2tpv3 class name | sequencing both [ resync ] | tos { reflect value 0-255 | value 0-255 } | transport-mode { ethernet vlan } | ttl value ]

no pw-class class name encapsulation l2tpv3 [ cookie size { 0 | 4 | 8 } | dfbit set | ipv4 source address | pmtu max 68-65535 | protocol l2tpv3 class name | sequencing both [ resync ] | tos { reflect value 0-255 | value 0-255 } | transport-mode { ethernet vlan } | ttl value ]

Syntax Description

class name

Configures an encapsulation class name.

cookie size {0 | 4 | 8}

(Optional) Configures the L2TPv3 cookie size setting:

  • 0—Cookie size is 0 bytes.
  • 4—Cookie size is 4 bytes.
  • 8—Cookie size is 8 bytes.
dfbit set

(Optional) Sets the Don't Fragment Bit (DFBIT)

ipv4 source address

(Optional) Configures the local source IPv4 address.

pmtu max 68-65535

(Optional) Configures the value of the maximum allowable session MTU.

protocol l2tpv3 class name

(Optional) Configures L2TPv3 as the signaling protocol for the pseudowire class.

sequencing both

(Optional) Configures sequencing on both transmit and receive side

resync

(Optional) Sets the threshold for out-of-sequence packets before resync

transport-mode

(Optional) Configures the remote transport mode

ethernet

Sets the transport mode as ethernet port mode

vlan

Sets the transport mode as vlan tagged mode

tos {reflect value 0-255 | value 0-255}

(Optional) Configures TOS and the TOS value. Range is 0 to 255.

ttl value

Configures the Time-to-live (TTL) value. Range is 1 to 255.

Command Default

None

Command Modes

L2VPN pseudowire class configuration

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to define L2TPV3 pseudowire encapsulation:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3

The following example shows how to set the encapsulation and protocol to L2TPV3:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

pw-class encapsulation mpls

Configures MPLS pseudowire encapsulation.  

pw-class encapsulation mpls

To configure MPLS pseudowire encapsulation, use the pw-class encapsulation mpls command in L2VPN pseudowire class configuration mode. To undo the configuration, use the no form of this command.

pw-class class-name encapsulation mpls { control word | ipv4 | load-balancing flow-label | preferred-path | protocol ldp | redundancy one-way | sequencing | switching tlv | tag-rewrite | transport-mode | vccv verification-type none }

no pw-class class-name encapsulation mpls { control word | ipv4 | load-balancing flow-label | preferred-path | protocol ldp | redundancy one-way | sequencing | switching tlv | tag-rewrite | transport-mode | vccv verification-type none }

Syntax Description

class-name

Encapsulation class name.

control word

Disables control word for MPLS encapsulation. Disabled by default.

ipv4

Sets the local source IPv4 address.

load-balancing flow-label

Sets flow label-based load balancing.

preferred-path

Configures the preferred path tunnel settings.

protocol ldp

Configures LDP as the signaling protocol for this pseudowire class.

redundancy one-way

Configures one-way PW redundancy behavior in the Redundancy Group.

sequencing

Configures sequencing on receive or transmit.

switching tlv

Configures switching TLV to be hidden or not.

tag-rewrite

Configures VLAN tag rewrite.

transport-mode

Configures transport mode to be either Ethernet or VLAN.

vccv none

Enables or disables the VCCV verification type.

Command Default

None

Command Modes

L2VPN pseudowire class configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

The following keywords were added:

  • preferred-path
  • sequencing
  • switching tlv
  • tag-rewrite
  • transport-mode
Release 4.2.0

The keyword redundancy one-way was introduced.

Release 4.3.0

The keyword load-balancing flow-label was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to define MPLS pseudowire encapsulation:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01 
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

pw-ether

To configure a PWHE Ethernet interface, use the pw-ether command in global configuration mode or in p2p configuration submode. To return to the default behavior, use the no form of this command.

pw-ether value

no pw-ether value

Syntax Description

value

Value of the PWHE Ethernet interface. The range is from 1 to 32768.

Command Default

None

Command Modes

Global configuration

p2p configuration

Command History

Release Modification
Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

interface (global configuration)

read, write

l2vpn (p2p configuration)

read, write

Examples

This example shows the sample output of a PWHE Ethernet interface configuration in global configuration mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)#  attach generic-interface-list interfacelist1

This example shows the sample output of a PWHE Ethernet interface configuration in p2p configuration submode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group xc1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)#p2p grp1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)#interface pw-ether 78

This example shows the sample output of L2 overhead configuration for the PW-HE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)# l2overhead 32

This example shows the sample output of Load-interval configuration for the PW-HE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)# load-interval 60

This example shows the sample output of how to set logging of interface state change for the PW-HE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)# logging events link-status

This example shows the sample output of MAC address configuration for the PW-HE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)# mac-address 44-37-E6-89-C3-93

This example shows the sample output of MTU configuration for the PW-HE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)# mtu 128

This example shows the sample output of bandwidth configuration for the PW-HE interface:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# interface pw-ether 78
RP/0/RSP0/CPU0:router(config-if)# bandwidth 256

Related Commands

Command

Description

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

pw-grouping

To enable Pseudowire Grouping, use the pw-grouping command in L2vpn configuration submode. To return to the default behavior, use the no form of this command.

pw-grouping

no pw-grouping

Syntax Description

pw-grouping

Enables Pseudowire Grouping.

Command Default

PW-grouping is disabled by default.

Command Modes

L2VPN configuration submode

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows the sample output of pw-grouping configuration in L2VPN configuration submode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-grouping

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

show l2vpn

Displays L2VPN information  

p2p

To enter p2p configuration submode to configure point-to-point cross-connects, use the p2p command in L2VPN xconnect mode. To return to the default behavior, use the no form of this command.

p2p xconnect-name

no p2p xconnect-name

Syntax Description

xconnect-name

(Optional) Configures the name of the point-to-point cross- connect.

Command Default

None

Command Modes

L2VPN xconnect

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The name of the point-to-point cross-connect string is a free format description string.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows a point-to-point cross-connect configuration (including pseudowire configuration):

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group group 1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p xc1

Related Commands

Command

Description

interface (p2p)

Configures an attachment circuit.  

sequencing (L2VPN)

To configure L2VPN pseudowire class sequencing, use the pw-class sequencing command in L2VPN pseudowire class encapsulation mode. To return to the default behavior, use the no form of this command.

sequencing { both | receive | transmit {resynch 5-65535} }

no sequencing { both | receive | transmit {resynch 5-65535} }

Syntax Description

both

Configures transmit and receive side sequencing.

receive

Configures receive side sequencing.

transmit

Configures transmit side sequencing.

resynch 5-65535

Configures the threshold for out-of-sequence packets before resynchronization. Range is 5 to 65535.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation mode

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Do not configure sequence resynch on high speed circuits. On low speed circuits, do not configure a threshold lower than 10 to 20 seconds of traffic.


Note


This command is not supported on the Cisco ASR 9000 Series Aggregation Services Router.



Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to configure L2VPN pseudowire class sequencing:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pw)# encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-encap-mpls)# sequencing both

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

show generic-interface-list

To display information about interface-lists, use the show generic-interface-list in EXEC mode.

show generic-interface-list [ location | name | retry | standby ]

Syntax Description

location

(Optional) Displays information about interface-lists for the specified location.

name

(Optional) Displays information about interface-lists for the specified interface list name.

retry

(Optional) Displays retry-list information.

standby

(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

The following example displays output for the show generic-interface-list command:

RP/0/RSP0/CPU0:router# show generic-interface-list
				Thu Aug  2 13:48:57.462 CDT
				generic-interface-list: nsrIL (ID: 1, interfaces: 2)
				   Bundle-Ether2 - items pending 0, downloaded to FIB
				   GigabitEthernet0/0/0/1 - items pending 0, downloaded to FIB
				 Number of items: 400
				 List is downloaded to FIB

The following example displays output for the show generic-interface-list retry private command:

RP/0/RSP0/CPU0:router# show generic-interface-list retry private
				Thu Aug  2 14:20:42.883 CDT
				total: 0 items

The following example displays output for the show generic-interface-list standby command:

RP/0/RSP0/CPU0:router# show generic-interface-list standby
				Thu Aug 2 14:25:01.749 CDT
				generic-interface-list: nsrIL (ID: 0, interfaces: 2)
				Bundle-Ether2 - items pending 0, NOT downloaded to FIB
				GigabitEthernet0/0/0/1 - items pending 0, NOT downloaded to FIB
				Number of items: 0
				List is not downloaded to FIB

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

show l2vpn

To display L2VPN information, use the show l2vpn command in EXEC mode.

show l2vpn

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

The following example displays output for the show l2vpn command. The output provides an overview of the state of the globally configured features.

RP/0/RSP0/CPU0:router# show l2vpn
	Mon May  7 15:01:17.963 BST
	PW-Status: disabled
	PW-Grouping: disabled
	Logging PW: disabled
	Logging BD state changes: disabled
	Logging VFI state changes: disabled
	Logging NSR state changes: disabled
	TCN propagation: disabled
	PWOAMRefreshTX: 30s			
				          

Examples

This example displays output for the show l2vpn command. The output provides an overview of the state of the globally configured features.
RP/0/RSP0/CPU0:router# show l2vpn
Tue Oct 16 14:34:36.116 BST
PW-Status: enabled
PW-Grouping: disabled
Logging PW: disabled
Logging BD state changes: disabled
Logging VFI state changes: disabled
Logging NSR state changes: disabled
TCN propagation: disabled
PW OAM transmit time: 30s
Multicast P2MP: enabled

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

pw-grouping

Enables Pseudowire Grouping  

show l2vpn atom-db

To display AToM database information, use the show l2vpn atom-db command in EXEC mode.

show l2vpn atom-db [ detail | l2-rid | ldp-rid | local-gid | neighbor | preferred-path | remote-gid | source ]

Syntax Description

detail

Specifies the details of the database.

l2-rid

Specifies the AToM database walking the L2 RID thread.

ldp-rid

Specifies the AToM database walking the LDP RID thread.

local-gid

Specifies the AToM database walking the Local GID thread.

neighbor

Specifies the details of the neighbor database.

preferred-path

Specifies the preferred path (tunnel) of the database

remote-gid

Specifies the AToM database walking the Remote GID thread.

source

Specifies the details of the source database.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

This example shows the sample output of the show l2vpn atom-db source 1.1.1.1 command:
RP/0/RSP0/CPU0:router# show l2vpn atom-db source 1.1.1.1
Peer ID         Source        VC ID      Encap    Signaling   FEC     Discovery 
2.2.2.2         1.1.1.1       1          MPLS     LDP         128     none      
This example shows the sample output of the show l2vpn atom-db source 1.1.1.1 detail command:
RP/0/RSP0/CPU0:router# show l2vpn atom-db source 1.1.1.1 detail
  PW: neighbor 2.2.2.2, PW ID 1, state is down ( provisioned )
    PW class class1, XC ID 0x1
    Encapsulation MPLS, protocol LDP
    Source address 1.1.1.1
    PW type Ethernet, control word disabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set

      MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        16000                          unknown                       
      Group ID     0x20000060                     0x0                           
      Interface    GigabitEthernet0/0/0/1.1       unknown                       
      MTU          1504                           unknown                       
      Control word disabled                       unknown                       
      PW type      Ethernet                       unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x6                            0x0                           
                                                  (none)                        
                   (router alert label)                                         
                   (TTL expiry)                                                 
      ------------ ------------------------------ -----------------------------
    MIB cpwVcIndex: 4278194081
    Create time: 13/12/2010 15:28:26 (20:32:27 ago)
    Last time status changed: 13/12/2010 15:28:26 (20:32:27 ago)
    Configuration info:
      PW class: class1
      Peer ID = 2.2.2.2, pseudowire ID = 1
      Control word is not set
      Transport mode: not set
        Configured (Static) Encapsulation: not set
        Provisioned Encapsulation: MPLS
      Static tag rewrite: not set
      MTU: 1504
      Tunnel interface: None
      IW type: 0
      PW type: Dynamic
      Pref path configured: No
      Bridge port: No
      BP learning disabled: No
      BP ucast flooding disabled: No
      BP bcast flooding disabled: No
      CW is mandatory: No
      Label: local unassigned, remote unassigned
      L2 Router-ID: 0.0.0.0
      LDP Router-ID: 0.0.0.0
      GR stale: No
    LDP Status: local established, remote unknown
    LDP tag rewrite: not set
    Force switchover: inactive
    MAC trigger: inactive
    VC sane: Yes
    Use PW Status: No
    Local PW Status: Up(0x0); Remote PW Status: Up(0x0)
    Peer FEC Failed: No
    LSP: Down
    Operational state: 
      LDP session state: down
      TE tunnel transport: No
      VC in gr mode: No
      Peer state: up
      Transport LSP down: Yes
      Advertised label to LDP: No
      Received a label from LSD: Yes
      Need to send standby bit: No
      VC created from rbinding: No
      PW redundancy dampening on : No
      Notified up : No
    Detailed segment state: down
     PW event trace history [Total events: 8]
     -----------------------------------------
     Time                Event                          Value           
     ====                =====                          ===========     
     12/13/2010 15:28:26 LSP Down                       0         
     12/13/2010 15:28:26 Provision                      0         
     12/13/2010 15:28:26 LSP Down                       0         
     12/13/2010 15:28:26 Connect Req                    0         
     12/13/2010 15:28:26 Rewrite create                 0x100000  
     12/13/2010 15:28:26 Got label                      0x3e80    
     12/13/2010 15:28:26 Local Mtu                      0x5e0 
    12/13/2010 15:28:26 Peer Up                        0

show l2vpn collaborators

To display information about the state of the interprocess communications connections between l2vpn_mgr and other processes, use the show l2vpn collaborators command in EXEC mode.

show l2vpn collaborators

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows sample output for the show l2vpn collaborators command:

RP/0/RSP0/CPU0:router# show l2vpn collaborators
L2VPN Collaborator stats:
Name                  State       Up Cnts      Down Cnts  
--------------------  ----------  -----------  -----------
IMC                    Down          0            0
LSD                    Up            1            0

This table describes the significant fields shown in the display.

Table 1 show l2vpn collaborators Field Descriptions

Field

Description

Name

Abbreviated name of the task interacting with l2vpn_mgr.

State

Indicates if l2vpn_mgr has a working connection with the other process.

Up Cnts

Number of times the connection between l2vpn_mgr and the other process has been successfully established.

Down Cnts

Number of times that the connection between l2vpn_mgr and the other process has failed or been terminated.

Related Commands

Command

Description

clear l2vpn collaborators

Clears the state change counters for L2VPN collaborators.  

show l2vpn database

To display L2VPN database, use the show l2vpn database command in EXEC mode.

show l2vpn database { ac | node }

Syntax Description

ac

Displays L2VPN Attachment Circuit (AC) database

node

Displays L2VPN node database.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

The following example displays output for the show l2vpn database ac command:

RP/0/RSP0/CPU0:router# show l2vpn database ac
				Bundle-Ether1.1:
				      Other-Segment MTU: 0
				      Other-Segment status flags: 0x0
				      Signaled capability valid: No
				      Signaled capability flags: 0x0
				      Configured capability flags: 0x0
				      XCID: 0xffffffff
				      PSN Type: Undefined
				      ETH data:
				          Xconnect tags: 0
				          Vlan rewrite tag: 0
				    AC defn:
				        ac-ifname: Bundle-Ether1.1
				        capabilities: 0x00368079
				        extra-capabilities: 0x00000000
				        parent-ifh: 0x020000e0
				        ac-type: 0x15
				        interworking: 0x00
				    AC info:
				        seg-status-flags: 0x00000000
				        segment mtu/l2-mtu: 1504/1518
				
				GigabitEthernet0/0/0/0.4096:
				      Other-Segment MTU: 0
				      Other-Segment status flags: 0x0
				      Signaled capability valid: No
				      Signaled capability flags: 0x0
				      Configured capability flags: 0x0
				      XCID: 0x0
				      PSN Type: Undefined
				      ETH data:
				          Xconnect tags: 0
				          Vlan rewrite tag: 0
				    AC defn:
				        ac-ifname: GigabitEthernet0_0_0_0.4096
				        capabilities: 0x00368079
				        extra-capabilities: 0x00000000
				        parent-ifh: 0x040000c0
				        ac-type: 0x15
				        interworking: 0x00
				    AC info:
				        seg-status-flags: 0x00000003
				        segment mtu/l2-mtu: 1504/1518

The following example displays output for the show l2vpn database node command:

RP/0/RSP0/CPU0:router# show l2vpn database node
				0/RSP0/CPU0
				    MA: vlan_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:31 Replay end rcvd                2               0
				
				
				    MA: ether_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:31 Replay end rcvd                0               0
				
				
				
				0/0/CPU0
				    MA: vlan_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:40 Replay end rcvd                6006            6001
				
				
				    MA: ether_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:31 Replay end rcvd                1               0

show l2vpn discovery

To display discovery label block information, use the show l2vpn discovery command in EXEC mode.

show l2vpn discovery { bridge-domain | xconnect | summary | private }

Syntax Description

bridge-domain

Displays bridge domain related forwarding information.

xconnect

Displays VPWS edge information.

summary

Displays summary information.

private

Displays private log or trace information.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following examples display output for the show l2vpn discovery command with bridge-domain filter:

RP/0/RSP0/CPU0:router#show l2vpn discovery bridge-domain

Service Type: VPLS,  Connected
  List of VPNs (8001 VPNs):

  Bridge group: bg1, bridge-domain: bg1_bd1, id: 0, signaling protocol: LDP
    VPLS-ID: (auto) 1:101
    Local L2 router id: 10.10.10.10
    List of Remote NLRI (3 NLRIs):
    Local Addr      Remote Addr     Remote L2 RID   Time Created   
    --------------- --------------- --------------- -------------------
    10.10.10.10     20.20.20.20     20.20.20.20     03/13/2010 21:27:05
    10.10.10.10     30.30.30.30     30.30.30.30     03/13/2010 21:27:05
    10.10.10.10     40.40.40.40     40.40.40.40     03/13/2010 21:27:05

The following examples display output for the show l2vpn discovery summary command:

RP/0/RSP0/CPU0:router#show l2vpn discovery summary 
Sun Mar 14 15:13:31.240 EDT
BGP: connected=yes,  active=yes,  stdby=yes
Services
  Bridge domain: registered=yes, Num VPNs=8001
   Num Local Edges=8001, Num Remote Edges=24001, Num Received NLRIs=24001
  Xconnect: registered=yes, Num VPNs=0
   Num Local Edges=0, Num Remote Edges=0, Num Received NLRIs=0

Related Commands

Command

Description

show l2vpn bridge-domain (VPLS)

Display information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains.  

show l2vpn forwarding

To display forwarding information from the layer2_fib manager on the line card, use the show l2vpn forwarding command in EXEC mode.

show l2vpn forwarding { bridge-domain | counter | debug | detail | dhcp binding | ethernet ring g8032 | gsp | hardware | inconsistent | interface | l2tp | l2tpv2 | location [node-id] | message | monitor-session | mstp | neighbor | object-queues | pbb | private | protection | resource | retry-list | summary | unresolved }

Syntax Description

bridge-domain

Displays bridge domain related forwarding information.

counter

Displays the cross-connect counters.

debug

Displays debug information.

detail

Displays detailed information from the layer2_fib manager.

dhcp binding

Displays DHCP binding related forwarding information

ethernet ring g8032

Displays Ethernet associated configuration information.

gsp

Displays GSP related forwarding information.

hardware

Displays hardware-related layer2_fib manager information.

inconsistent

Displays inconsistent entries only.

interface

Displays the match AC subinterface.

l2tp

Displays L2TPv3 related forwarding information.

l2tpv2

Displays l2tpv2 related forwarding information.

location node-id

Displays layer2_fib manager information for the specified location. The node-id argument is entered in the rack/slot/module notation.

message

Displays messages exchanged with collaborators.

monitor-session

Displays the match Monitor-session.

mstp

Displays multi-spanning tree related forwarding information.

neighbor

Displays the match neighbor IP address.

object-queues

Displays object queues related information.

pbb

Displays l2vpn provider backbone bridge information.

private

Output includes private information.

protection

Displays protection associated interfaces related forwarding information.

resource

Displays resource availability information in the layer2_fib manager.

retry-list

Displays retry list related information.

summary

Displays summary information about cross-connects in the layer2_fib manager.

unresolved

Displays unresolved entries only.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.3.0
The following keywords were introduced:
  • debug
  • dhcp binding
  • ethernet ring g8032
  • gsp
  • l2tpv2
  • monitor-session
  • neighbor
  • object-queues
  • pbb
  • private
  • protection
   

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

The following sample output is from the show l2vpn forwarding bridge detail location command:

RP/0/RSP0/CPU0:router# show l2vpn forwarding location 0/2/cpu0
Bridge-domain name: bg1:bd1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 IGMP snooping: disabled, flooding: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 1
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0

  GigabitEthernet0/1/0/1.2, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0 


Bridge-domain name: bg1:bd2, id: 1, state: up
  Type:  pbb-edge, I-SID: 1234
  Core-bridge: pbb-bd2
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 IGMP snooping: disabled, flooding: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 0
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0

 PBB Edge, state: up
    Number of MAC: 0
 GigabitEthernet0/1/0/1.3, state: oper up
    Number of MAC: 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0 

Bridge-domain name: bg1:bd3, id: 2, state: up
  Type:  pbb-core 
  Number of associated pbb-edge BDs: 1

MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 IGMP snooping: disabled, flooding: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 0
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0

  PBB Core, state: up
  Vlan-id: 1
 
  GigabitEthernet0/1/0/1.4, state: oper up
    Number of MAC: 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0 

The following sample outputs shows the backup pseudowire information:

RP/0/RSP0/CPU0:router#show l2vpn forwarding detail location 0/2/CPU0
Local interface: GigabitEthernet0/2/0/0.1, Xconnect id: 0x3000001, Status: up
  Segment 1
    AC, GigabitEthernet0/2/0/0.1, Ethernet VLAN mode, status: Bound
    RG-ID 1, active
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Segment 2
    MPLS, Destination address: 101.101.101.101, pw-id: 1000, status: Bound
    Pseudowire label: 16000
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Backup PW
    MPLS, Destination address: 102.102.102.102, pw-id: 1000, status: Bound
    Pseudowire label: 16001
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
RP/0/RSP0/CPU0:router#show l2vpn forwarding bridge-domain detail location 0/2/CPU0
Bridge-domain name: bg1:bd1, id: 0, state: up
….
  GigabitEthernet0/2/0/0.4, state: oper up
    RG-ID 1, active
    Number of MAC: 0
    …..

  Nbor 101.101.101.101 pw-id 5000
    Backup Nbor 101.101.101.101 pw-id 5000
    Number of MAC: 0
….

The following sample outputs displays the SPAN segment information of the xconnect:

RP/0/RSP0/CPU0:router# show l2vpn forwarding counter location 0/7/CPU0 
Legend: ST = State, DN = Down

Segment 1                             Segment 2           ST     Byte
                                                                                Switched
----------------------------- -----------------------    --      ---------
pw-span-test (Monitor-Session) mpls  2.2.2.2  UP       0
RP/0/RSP0/CPU0:router #Show l2vpn forwarding monitor-session location 0/7/CPU0
Segment 1                            Segment 2                            State
------------------------------------ ------------------------------------ ------
pw-span-test(monitor-session)  mpls    2.2.2.2                      UP
pw-span-sess(monitor-session)  mpls    3.3.3.3                      UP
RP/0/RSP0/CPU0:router #Show l2vpn forwarding monitor-session pw-span-test location 0/7/CPU0
Segment 1                                 Segment 2                            State
------------------------------------ ------------------------------------ ------
pw-span-test(Monitor-Session) mpls    2.2.2.2                      UP


Example 4:
RP/0/RSP0/CPU0:router #show l2vpn forwarding detail location 0/7/CPU0
  Xconnect id: 0xc000001, Status: up
  Segment 1
    Monitor-Session, pw-span-test, status: Bound
  Segment 2
    MPLS, Destination address: 2.2.2.2, pw-id: 1, status: Bound
    Pseudowire label: 16001
    Statistics:
      packets: received 0, sent 11799730
      bytes: received 0, sent 707983800

Example 5:
show l2vpn forwarding private location 0/11/CPU0
  Xconnect ID 0xc000001
  Xconnect info:
   Base info: version=0xaabbcc13, flags=0x0, type=2, reserved=0
    xcon_bound=TRUE, switching_type=0, data_type=3

  AC info:
   Base info: version=0xaabbcc11, flags=0x0, type=3, reserved=0
    xcon_id=0xc000001, ifh= none, subifh= none, ac_id=0, ac_type=SPAN,
    ac_mtu=1500, iw_mode=none, adj_valid=FALSE, adj_addr none
    

  PW info:
   Base info: version=0xaabbcc12, flags=0x0, type=4, reserved=0
    pw_id=1, nh_valid=TRUE, sig_cap_flags=0x20, context=0x0,
     MPLS, pw_label=16001
    Statistics:
      packets: received 0, sent 11799730
      bytes: received 0, sent 707983800

   Object: NHOP
   Event Trace History [Total events: 5]
--------------------------------------------------------------------
     Time                Event                Flags
     ====                =====                =====
   

--------------------------------------------------------------------


  Nexthop info:
   Base info: version=0xaabbcc14, flags=0x10000, type=5, reserved=0
    nh_addr=2.2.2.2, plat_data_valid=TRUE, plat_data_len=128, child_count=1

   Object: XCON
   Event Trace History [Total events: 16]
--------------------------------------------------------------------
     Time                Event                Flags
     ====                =====                =====

 -------------------------------------------------------------------
RP/0/RSP0/CPU0:router #show l2vpn forwarding summary location 0/7/CPU0
 Major version num:1, minor version num:0
Shared memory timestamp:0x31333944cf
Number of forwarding xconnect entries:2
  Up:2  Down:0
  AC-PW:1 (1 mpls)  AC-AC:0  AC-BP:0  AC-Unknown:0
  PW-BP:0  PW-Unknown:0 Monitor-Session-PW:1
Number of xconnects down due to:
  AIB:0  L2VPN:0  L3FIB:0
Number of p2p xconnects: 2
Number of bridge-port xconnects: 0
Number of nexthops:1
  MPLS:   Bound:1  Unbound:0  Pending Registration:0
Number of bridge-domains: 0
Number of static macs: 0
Number of locally learned macs: 0
Number of remotely learned macs: 0
Number of total macs: 0

The following sample output is from the show l2vpn forwarding command:

RP/0/RSP0/CPU0:router# show l2vpn forwarding location 0/2/cpu0

ID   Segment 1         Segment 2   
-----------------------------------
1    Gi0/2/0/0 1       1.1.1.1   9)

The following sample output shows the MAC information in the layer2_fib manager summary:

RP/0/RSP0/CPU0:router# show l2vpn forwarding summary location 0/3/CPU0

Major version num:1, minor version num:0
Shared memory timestamp:0x66ff58e894
Number of forwarding xconnect entries:2
  Up:1  Down:0
  AC-PW:0  AC-AC:0  AC-BP:1 PW-BP:1
Number of xconnects down due to:
  AIB:0  L2VPN:0  L3FIB:0
Number of nexthops:1
Number of static macs: 5
Number of locally learned macs: 5
Number of remotely learned macs: 0
Number of total macs: 10
This example shows the sample output of a configured flow label:
RP/0/RSP0/CPU0:router# show l2vpn forwarding detail location 0/0/cPU0
Local interface: GigabitEthernet0/0/1/1, Xconnect id: 0x1000002, Status: up
  Segment 1
    AC, GigabitEthernet0/0/1/1, Ethernet port mode, status: Bound
    Statistics:
      packets: received 24849, sent 24847
      bytes: received 1497808, sent 1497637
  Segment 2
    MPLS, Destination address: 3.3.3.3, pw-id: 2, status: Bound, Active
    Pseudowire label: 16004    Control word disabled
    Backup PW
      MPLS, Destination address: 2.2.2.2, pw-id: 6, status: Bound
      Pseudowire label: 16000
    Flow label enabled
    Statistics:
      packets: received 24847, sent 24849
      bytes: received 1497637, sent 1497808
					Xconnect id: 0xff000014, Status: down
  Segment 1
    MPLS, Destination address: 2.2.2.2, pw-id: 1, status: Not bound
		Pseudowire label: UNKNOWN    Control word disabled
    Flow label enabled
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Segment 2
    Bridge id: 0, Split horizon group id: 0
    Storm control: disabled
    MAC learning: enabled
    MAC port down flush: enabled
    Flooding:
      Broadcast & Multicast: enabled
      Unknown unicast: enabled
    MAC aging time: 300 s, Type: inactivity
    MAC limit: 4000, Action: none, Notification: syslog
    MAC limit reached: no
    Security: disabled
    DHCPv4 snooping: profile not known on this node, disabled
    IGMP snooping profile: profile not known on this node 
    Router guard disabled
This example shows sample output for the show l2vpn forwarding location command:
RP/0/RSP0/CPU0:router# show l2vpn forwarding location 0/1/CPU0
LC/0/1/CPU0:JSegment 1                            Segment 2               State 
------------------------------------ ------------------------------------ ---
PBB Edge                             Bridge id 0, SHG id 0                 UP     
Gi0/1/0/1.1(Eth VLAN)                Bridge id 0, SHG id 0                 UP     
Gi0/1/0/1.2(Eth VLAN)                Bridge id 0, SHG id 0                 UP     
mpls    1.2.3.4,22                   Bridge id 1, SHG id 0                 DN     
PBB Core                             Bridge id 2, SHG id 0                 UP     
This example shows sample output for the show l2vpn forwarding summary location command:
RP/0/RSP0/CPU0:router# show l2vpn forwarding summary location 0/0/CPU0
Major version num:1, minor version num:0
Shared memory timestamp:0x4005e57a0
Number of forwarding xconnect entries:4
  Up:4  Down:0
  AC-PW:0  AC-AC:0  AC-BP:0  AC-Unknown:0
  PW-BP:0  PW-Unknown:0
  PBB-BP:4  PBB-Unknown:0
Number of xconnects down due to:
  AIB:0  L2VPN:0  L3FIB:0
Number of p2p xconnects: 0
Number of bridge-port xconnects: 4
Number of nexthops:0
Number of bridge-domains: 5
Number of static macs: 0
Number of locally learned macs: 0
Number of remotely learned macs: 0
Number of total macs: 0                                            
This example shows sample output for the show l2vpn forwarding detail location command:
RP/0/RSP0/CPU0:router# show l2vpn forwarding detail location 0/1/CPU0
Local interface: PBB Edge, Xconnect id: 0x2000001, Status: up
  Segment 1
    PBB Edge
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Segment 2
    Bridge id: 0, Split horizon group id: 0
    Storm control: disabled
    MAC learning: enabled
    Flooding:
      Broadcast & Multicast: enabled
      Unknown unicast: enabled
    MAC aging time: 300 s, Type: inactivity
    MAC limit: 4294967295, Action: none, Notification: syslog
    MAC limit reached: no
    Security: disabled
    DHCPv4 snooping: profile not known on this node, disabled
    IGMP snooping profile: profile not known on this node 
    Router guard disabled
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0 

Local interface: PBB Core, Xconnect id: 0x2000001, Status: up
  Segment 1
    PBB Core
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Segment 2
    Bridge id: 0, Split horizon group id: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
   

The following sample output is from the show l2vpn forwarding command:

RP/0/RSP0/CPU0:router# show l2vpn for location 0/0/CPU0

Fri May 18 13:56:35.957 EDT
Segment 1 Segment 2 State
------------------------------------ ------------------------------------ ------
Gi0/0/0/4.2(Eth VLAN) l2tpv3 UP
1111:2222::cdef
Gi0/0/0/4.3(Eth VLAN) mpls 1.2.3.4 DN

The following sample output is from the show l2vpn forwarding neighbor ipv6 command:

RP/0/RSP0/CPU0:router# show l2vpn forwarding neighbor ipv6 1111:2222::cdef detail loc 0/0/cpu0

Fri May 18 13:58:14.720 EDT
Local interface: GigabitEthernet0/0/0/4.2, Xconnect id: 0x2, Status: up
Segment 1
AC, GigabitEthernet0/0/0/4.2, Ethernet VLAN mode, status: Bound
Statistics:
packets: received 0, sent 0
bytes: received 0, sent 0
Segment 2
L2TPv3-IPV6, Destination address: 1111:2222::cdef, status: Bound
Source address: 1111:2222::abcd
Local session:
Session ID: -1
Cookie: size 0 bytes
Remote session:
Session ID: -1
Cookie: size 0 bytes
Control word disabled
Sequencing not set
TOS 40 (reflect disabled), TTL 255, DF bit not set
Path MTU: disabled
Statistics:
packets: received 0, sent 0
bytes: received 0, sent 0
packets dropped: out of sequence 0, other 0
This example shows sample output for the show l2vpn forwarding detail location command with P2MP PW enabled on the PW BP.
RP/0/RSP0/CPU0:router# show l2vpn forwarding detail location 
Xconnect id: 0xfffc0003, Status: up
  Segment 1
    MPLS, Destination address: 2.2.2.2, pw-id: 101, status: Bound
    Pseudowire label: 16002    Control word disabled
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Segment 2
    Bridge id: 0, Split horizon group id: 1
    Storm control: disabled
    MAC learning: enabled
    MAC port down flush: enabled
    Flooding:
      Broadcast & Multicast: enabled
      Unknown unicast: enabled
    MAC aging time: 300 s, Type: inactivity
    MAC limit: 4000, Action: none, Notification: syslog
    MAC limit reached: no
    MAC Secure: disabled, Logging: disabled
    DHCPv4 snooping: profile not known on this node, disabled
    Dynamic ARP Inspection: disabled, Logging: disabled
    IP Source Guard: disabled, Logging: disabled
    IGMP snooping profile: profile not known on this node 
    Router guard disabled
    P2MP PW enabled

This example shows sample output for the show l2vpn forwarding summary location command displaying number of bridge-domains with P2MP PW enabled.
RP/0/RSP0/CPU0:router# show l2vpn forwarding summary location
Mon Sep 9 22:07:54.000 EDT
Major version num:1, minor version num:0
Shared memory timestamp:0x547395c50
Global configuration:
Number of forwarding xconnect entries:5
  Up:0  Down:5
  AC-PW(atom):1 AC-PW(l2tpv2):0 AC-PW(l2tpv3):0
 (1 mpls)  AC-AC:0  AC-BP:0  AC-Unknown:0
  PW-BP:4  PW-Unknown:0
  PBB-BP:0  PBB-Unknown:0
  Monitor-Session-PW:0  Monitor-Session-Unknown:0
Number of xconnects down due to:
  AIB:0  L2VPN:5  L3FIB:0  VPDN:0
Number of xconnect updates dropped due to:
  Invalid XID: 0 VPWS PW, 0 VPLS PW, 0 Virtual-AC, 0 PBB
  Exceeded max allowed: 0 VPLS PW, 0 Bundle-AC
Number of p2p xconnects: 1
Number of bridge-port xconnects: 4
Number of nexthops:2
  MPLS:   Bound:2  Unbound:0  Pending Registration:0
  P2MP MLDP: Bound:1  Unbound:0  Pending Registration:0
  P2MP TE:   Bound:1  Unbound:0  Pending Registration:0
Number of bridge-domains: 2 (0 with routed interface, 2 with P2MP enabled)
Number of bridge-domain updates dropped: 0
Number of static macs: 0
Number of routed macs: 0
Number of locally learned macs: 0
Number of remotely learned macs: 0
Number of total macs: 0
Number of total P2MP Ptree entries: 2
  MLDP:1 (LMRIB:1) RSVP-TE:0 (LMRIB:0)

Related Commands

Command

Description

clear l2vpn forwarding counters

Clears L2VPN forwarding counters.  

show l2vpn forwarding message counters

To display L2VPN forwarding messages exchanged with L2FIB Collaborators, use the show l2vpn forwarding message counters command in EXEC mode.

show l2vpn forwarding message counters { hardware | location node-id }

Syntax Description

hardware

Displays message counter information from hardware.

location node-id

Displays message counter information for the specified location.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

The following examples shows the output from the show l2vpn forwarding message counters location command:
RP/0/RSP0/CPU0:router# show l2vpn forwarding message counters location 0/1/CPU0
Messages exchanged with L2FIB Collaborators:
-----------------------------------------------------------------------------------
     Message                                            Count       Info1        Info2        Time               
     =======                                            =====       =====        =====        ====               
     l2vpn provision messages received:                  0          0x0          0x0          -                  
     l2vpn unprovision messages received:                0          0x0          0x0          -                  
     l2vpn bridge provision messages received:           2          0x1          0x0          Jan  8 14:49:19.283
     l2vpn bridge unprovision messages received:         0          0x0          0x0          -                  
     l2vpn bridge main port update messages received:    1          0x2000300    0x0          Jan  8 12:02:15.628
     l2vpn bridge main port update w/ action=MSTI_DELETE 0          0x0          0x0          -                  
     l2vpn bridge main port update ACK sent:             1          0x2000300    0x0          Jan  8 12:02:15.628
     l2vpn bridge port provision messages received:      1          0x2000002    0x0          Jan  8 12:02:15.629
     l2vpn bridge port unprovision messages received:    0          0x0          0x0          -                  
     l2vpn shg provision messages received:              0          0x0          0x0          -                  
     l2vpn shg unprovision messages received:            0          0x0          0x0          -                  
     l2vpn static mac provision messages received:       1          0x0          0x0          Jan  9 08:41:36.668
     l2vpn static mac unprovision messages received:     1          0x0          0x0          Jan  9 08:44:24.208
     l2vpn dynamic mac local learning messages received: 0          0x0          0x0          -                  
     l2vpn dynamic mac remote learning messages received 0          0x0          0x0          -                  
     l2vpn dynamic mac refresh messages received:        0          0x0          0x0          -                  
     l2vpn dynamic mac unprovision messages received:    0          0x0          0x0          -                  
     AIB update messages received:                       4          0x2000102    0x2000300    Jan  8 12:02:15.622
     AIB delete messages received:                       0          0x0          0x0          -                  
     FIB nhop registration messages sent:                0          0x0          0x0          -                  
     FIB nhop unregistration messages sent:              0          0x0          0x0          -                  
     FIB ecd ldi update messages received:               0          0x0          0x0          -                  
     FIB invalid NHOP prov messages received:            0          0x0          0x0          -                  
     Backbone-source-mac prov messages received:         0          0x0          0x0          -          
     Backbone-source-mac unprov messages received:       0          0x0          0x0          -

Related Commands

Command

Description

clear l2vpn forwarding message counters

Clears L2VPN forwarding message counters.  

show l2vpn generic-interface-list

To display all the L2VPN virtual interfaces, use the show l2vpn generic-interface-list command in EXEC mode.

show l2vpn generic-interface-list { detail | name | private | summary }

Syntax Description

detail

Specifies the details of the interface.

name

Specifies the name of the interface.

private

Specifies the private details of the interface.

summary

Specifies the summary information of the interface.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

This example shows the sample output of the show l2vpn generic-interface-list command:
RP/0/RSP0/CPU0:router# show l2vpn generic-interface-list
generic-interface-list: l1 (ID: 2, interfaces: 2)  Number of items: 20
generic-interface-list: l2 (ID: 3, interfaces: 4)  Number of items: 15
This example shows the sample output of the show l2vpn generic-interface-list detail command:
RP/0/RSP0/CPU0:router# show l2vpn generic-interface-list detail
generic-interface-list: l1 (ID: 2, interfaces: 2)
   GigabitEthernet0/1/0/0 - items pending 2
   GigabitEthernet0/1/0/1 - items pending 4
   Number of items: 27
    PW-Ether: 1-10, 12-21
    PW-IW: 1-7

generic-interface-list: l2 (ID: 3, interfaces: 4)
   GigabitEthernet0/1/0/0 - items pending 2
   GigabitEthernet0/1/0/1 - items pending 4
   GigabitEthernet0/1/0/2 - items pending 1
   GigabitEthernet0/1/0/3 - items pending 0
   Number of items: 20
    PW-Ether: 1-15
    PW-IW: 1-7
This example shows the sample output of the show l2vpn generic-interface-list name | detail command:
RP/0/RSP0/CPU0:router# show l2vpn generic-interface-list name 11 detail
generic-interface-list: l1 (ID: 2, interfaces: 2)
   GigabitEthernet0/1/0/0 - items pending 2
   GigabitEthernet0/1/0/1 - items pending 4
   Number of items: 20
    PW-Ether 1-10, 12-21

show l2vpn index

To display statistics about the index manager, use the show l2vpn index command in EXEC mode.

show l2vpn index [ location | private | standby ]

Syntax Description

location

(Optional) Displays index manager statistics for the specified location.

private

(Optional) Detailed information about all indexes allocated for each pool.

standby

(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 4.2.1

This command was introduced.

Release 4.3.0

The following keywords are introduced:

  • location
  • standby

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

This example shows the sample output of the show l2vpn index command:
RP/0/RSP0/CPU0:router# show l2vpn index
			Pool id: 0x4, App: RD 
   Pool size: 32767
   zombied IDs: 0
   allocated IDs: 0

   Pool id: 0x5, App: IFLIST 
   Pool size: 65535
   zombied IDs: 0
   allocated IDs: 2

   Pool id: 0xff000001, App: PW/PBB/Virtual AC 
   Pool size: 40960
   zombied IDs: 0
   allocated IDs: 1

   Pool id: 0xff000002, App: BD 
   Pool size: 4095
   zombied IDs: 0
   allocated IDs: 2

   Pool id: 0xff000003, App: MP2MP 
   Pool size: 65535
   zombied IDs: 0
   allocated IDs: 1
This example shows the sample output of the show l2vpn index standby command:
RP/0/RSP0/CPU0:router# show l2vpn index standby
			 Pool id: 0xfffc0000, App: Global
			   Max number of ID mgr instances: 1
			   ID mgr instances in use: 1
			   Pool size: 98304
			   zombied IDs: 0
			   allocated IDs: 0
			
			 Pool id: 0xfffc0002, App: BD
			   Max number of ID mgr instances: 1
			   ID mgr instances in use: 1
			   Pool size: 8192
			   zombied IDs: 0
			   allocated IDs: 0
			
			 Pool id: 0xfffc0003, App: MP2MP
			   Max number of ID mgr instances: 1
			   ID mgr instances in use: 1
			   Pool size: 65535
			   zombied IDs: 0
			   allocated IDs: 0

show l2vpn nsr

To configure non-stop routing, use the show l2vpn nsr command in EXEC mode.

show l2vpn nsr [ location | private | standby ]

Syntax Description

location

(Optional) Displays non-stop routing information for the specified location.

private

(Optional) Displays detailed non-stop routing information.

standby

(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

The following example displays output for the show l2vpn nsr command:

RP/0/RSP0/CPU0:router# show l2vpn nsr
				L2VPN NSR state is Declared Ready
				Number of LDP sessions synced           : 505
				Number of LDP sessions not synced       : 0
				Number of LDP sessions sync not required: 0

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

nsr (L2VPN)

Configures non-stop routing.  

show l2vpn provision queue

To display L2VPN configuration provisioning queue information, use the show l2vpn provision queue command in EXEC mode.

show l2vpn provision queue [ location | standby ]

Syntax Description

location

(Optional) Displays L2VPN configuration provisioning queue information for the specified location.

standby

(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

The following example displays output for the show l2vpn provision queue command:

RP/0/RSP0/CPU0:router# show l2vpn provision queue
				
				Legend: P/P/R = Priority/Provisioned/Require Provisioning.
				Configuration Item         Object Type              Class                  P/P/R Object Key
				-------------------------- ------------------------ ---------------------- ----- ----------
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS01
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS02
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS03

The following example displays output for the show l2vpn provision queue standby command:

RP/0/RSP0/CPU0:router# show l2vpn provision queue standby
				Legend: P/P/R = Priority/Provisioned/Require Provisioning.
				Configuration Item         Object Type              Class                  P/P/R Object Key
				-------------------------- ------------------------ ---------------------- ----- ----------
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS01
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS02
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS03
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS04
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS05
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS06
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS07
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS08
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS09
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS010

Related Commands

Command

Description

l2vpn

Enters L2VPN configuration mode.  

show l2vpn pw-class

To display L2VPN pseudowire class information, use the show l2vpn pw-class command in EXEC mode.

show l2vpn pw-class [ detail | location | name class name | standby ]

Syntax Description

detail

(Optional) Displays detailed information.

location

(Optional) Displays location specific information.

name class-name

(Optional) Displays information about a specific pseudowire class name.

standby

(Optional) Displays standby node specific information.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.3.0

The keywords location and standby were introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

The following example shows sample output for the show l2vpn pw-class command:

RP/0/RSP0/CPU0:router# show l2vpn pw-class

Name                        Encapsulation     Protocol       
-------------------------   ----------        ----------     
mplsclass_75                MPLS              LDP 
l2tp-dynamic                L2TPv3            L2TPv3         
This example shows sample output for the show l2vpn pw-class detail command:
RP/0/RSP0/CPU0:router# show l2vpn pw-class detail
				Encapsulation MPLS, protocol LDP
    Transport mode not set, control word unset (default)
    Sequencing not set
    Static tag rewrite not set
    PW Backup disable delay: 0 sec 
    MAC withdraw message is sent over PW: no
    IPv4 source address 1.1.1.1 

This table describes the significant fields shown in the display.

Table 2  show l2vpn pw-class Command Field Descriptions

Field

Description

Name

Displays the name of the pseudowire class.

Encapsulation

Displays the encapsulation type.

Protocol

Displays the protocol type.

Related Commands

Command

Description

clear l2vpn forwarding counters

Clears L2VPN forwarding counters.  

show l2vpn pwhe

To display the pseudowire headend (PWHE) information, use the show l2vpn pwhe command in EXEC mode.

show l2vpn pwhe { detail | interface | summary }

Syntax Description

detail

Specifies the details of the interface.

interface

Specifies the name of the interface.

summary

Specifies the summary information of the interface.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

This example show the sample output for show l2vpn pwhe detail command:
RP/0/RSP0/CPU0:router# show l2vpn pwhe detail
Interface: PW-Ether1   Interface State: Down, Admin state: Up
  Interface handle 0x20000070
  MTU:  1514
  BW:   10000 Kbit
  Interface MAC addresses: 0279.96e9.8205
  Label: 16000
  L2-overhead: 0
  VC-type: 5
  CW: N
  Generic-interface-list: ifl1 (id: 1)
   Gi0/2/0/1, in bundle BE3, state: Up, replication: success
   Gi0/2/0/0, in bundle BE5, state: Up, replication: success
   Gi0/2/0/2, in bundle BE5, state: Up, replication: success
   Gi0/2/0/3, state: Up, replication: success

Interface: PW-IW1   Interface State: Up, Admin state: Up
  Interface handle 0x20000070
  MTU:  1514
  BW:   10000 Kbit
  VC-type: 11
  CW: N
  Generic-interface-list: ifl2 (id: 2)
   Gi0/3/0/1, in bundle BE6, state: Up, replication: success
   Gi0/3/0/0, in bundle BE6, state: Up, replication: success
   Gi0/3/0/2, state: Up, replication: success
   Gi0/3/0/3, state: Up, replication: success
This example show the sample output for show l2vpn pwhe summary command:
RP/0/RSP0/CPU0:router# show l2vpn pwhe summary
		Number of PW-HE interface: 1600
  Up: 1300 Down: 300 Admindown: 0
  Number of PW-Ether interfaces: 900
  Up: 700  Down: 200  Admindown: 0
  Number of PW-IW interfaces: 700
  Up: 600  Down: 100  Admindown: 0

show l2vpn resource

To display the memory state in the L2VPN process, use the show l2vpn resource command in EXEC mode.

show l2vpn resource

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read

Examples

The following example shows sample output for the show l2vpn resource command:

RP/0/RSP0/CPU0:router# show l2vpn resource

Memory: Normal

describes the significant fields shown in the display.Table 1

Table 3 show l2vpn resource Command Field Descriptions

Field

Description

Memory

Displays memory status.

show l2vpn trace

To display trace data for L2VPN, use the show l2vpn trace command in EXEC mode.

show l2vpn trace [ checker | file | hexdump | last | location | reverse | stats | tailf | unique | usec | verbose | wide | wrapping ]

Syntax Description

checker

Displays trace data for the L2VPN Uberverifier.

file

Displays trace data for the specified file.

hexdump

Display traces data in hexadecimal format.

last

Display last <n> entries

location

Displays trace data for the specified location.

reverse

Display latest traces first

stats

Display trace statistics

tailf

Display new traces as they are added

unique

Display unique entries with counts

usec

Display usec details with timestamp

verbose

Display internal debugging information

wide

Display trace data excluding buffer name, node name, tid

wrapping

Display wrapping entries

Command Default

None

Command Modes

EXEC

Command History

Release Modification
Release 4.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

l2vpn

read

Examples

This example displays output for the show l2vpn trace command:

RP/0/RSP0/CPU0:router# show l2vpn trace
				310 unique entries (1775 possible, 0 filtered)
				Jul 27 14:39:51.786 l2vpn/fwd-detail 0/RSP0/CPU0 2# t1  FWD_DETAIL:415: l2tp session table rebuilt
				Jul 27 14:39:52.106 l2vpn/issu 0/RSP0/CPU0 1# t1  ISSU:788: ISSU - iMDR init called; 'infra/imdr' detected the 'informational' condition 'the service is not supported in the node'
				Jul 27 14:39:52.107 l2vpn/issu 0/RSP0/CPU0 1# t1  ISSU:428: ISSU - attempt to start COLLABORATOR wait timer while not in ISSU mode
				Jul 27 14:39:54.286 l2vpn/fwd-common 0/RSP0/CPU0 1# t1  FWD_COMMON:3257: show edm thread initialized
				Jul 27 14:39:55.270 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC|ERR:783: Mac aging init
				Jul 27 14:39:55.286 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:1765: l2vpn_gsp_cons_init returned No error
				Jul 27 14:39:55.340 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:1792: Client successfully joined gsp group
				Jul 27 14:39:55.340 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:779: Initializing the txlist IPC thread
				Jul 27 14:39:55.341 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:2971: gsp_optimal_msg_size = 4832 (real: True)
				Jul 27 14:39:55.351 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:626: Entering mac aging timer init

This example displays output with MIRP-Lite entries for the show l2vpn trace command:

RP/0/RSP0/CPU0:router# show l2vpn trace
				310 unique entries (1775 possible, 0 filtered)
				Jul 27 14:39:51.786 l2vpn/fwd-detail 0/RSP0/CPU0 2# t1  FWD_DETAIL:415: l2tp session table rebuilt
				Jul 27 14:39:52.106 l2vpn/issu 0/RSP0/CPU0 1# t1  ISSU:788: ISSU - iMDR init called; 'infra/imdr' detected the 'informational' condition 'the service is not supported in the node'
				Jul 27 14:39:52.107 l2vpn/issu 0/RSP0/CPU0 1# t1  ISSU:428: ISSU - attempt to start COLLABORATOR wait timer while not in ISSU mode
				Jul 27 14:39:54.286 l2vpn/fwd-common 0/RSP0/CPU0 1# t1  FWD_COMMON:3257: show edm thread initialized
				Jul 27 14:39:55.270 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC|ERR:783: Mac aging init
				Jul 27 14:39:55.286 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:1765: l2vpn_gsp_cons_init returned No error
				Jul 27 14:39:55.340 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:1792: Client successfully joined gsp group
				Jul 27 14:39:55.340 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:779: Initializing the txlist IPC thread
				Jul 27 14:39:55.341 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:2971: gsp_optimal_msg_size = 4832 (real: True)
				Jul 27 14:39:55.351 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:626: Entering mac aging timer init
				Jul 27 14:39:55.361 l2vpn/fwd-common 0/RSP0/CPU0 t1  FWD_COMMON:1522: #############MIRP_LITE_SPIO
				Jul 27 14:39:55.362 l2vpn/fwd-common 0/RSP0/CPU0 t1  FWD_COMMON:1561: MIRP-lite init finished
				Jul 27 14:39:55.362 l2vpn/fwd-common 0/RSP0/CPU0 t1  FWD_COMMON:1563: MIRP-lite

show l2vpn xconnect

To display brief information on configured cross-connects, use the show l2vpn connect command in EXEC mode.

show l2vpn xconnect [ brief | detail | encapsulation | group | groups | interface | location | mp2mp | neighbor | pw-class | standby | state | summary | type { ac-pw | locally-switched | monitor-session-pw | ms-pw } ]

Syntax Description

brief

(Optional) Displays encapsulation brief information.

detail

(Optional) Displays detailed information.

encapsulation

(Optional) Filters on encapsulation type.

group

(Optional) Displays all cross-connects in a specified group.

groups

(Optional) Displays all groups information.

interface

(Optional) Filters on interface and subinterface.

location

(Optional) Displays location specific information.

mp2mp

(Optional) Displays MP2MP information.

mpsw

(Optional) Displays ms_pw information.

neighbor

(Optional) Filters on neighbor.

private

(Optional) Displays private information.

pw-class

(Optional) Filters on pseudowire class

standby

(Optional) Displays standby node specific information.

state

(Optional) Filters the following xconnect state types:

  • up
  • down
summary

(Optional) Displays AC information from the AC Manager database.

type

(Optional) Filters the following xconnect types:

  • ac-pw
  • locally switched
  • monitor-session-pw
  • ms-pw

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.3.0
The following keywords were introduced:
  • location
  • standby

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If a specific cross-connect is specified in the command (for instance, AC_to_PW1) then only that cross-connect will be displayed; otherwise, all cross-connects are displayed.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows sample output for the show l2vpn xconnect command:

RP/0/RSP0/CPU0:router# show l2vpn xconnect

Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
              LU = Local Up, RU = Remote Up, CO = Connected

XConnect                   Segment 1                   Segment 2                
Group      Name       ST   Description            ST   Description            ST
----------------------------   ---------------------------   -------------------------
g1           x1        UP   pw-span-test           UP   2.2.2.2          1      UP

siva_xc    siva_p2p   UP   Gi0/4/0/1              UP   10.1.1.1         1      UP
                                                       Backup                   
                                                       10.2.2.2         2      UP
--------------------------------------------------------------------------------

The following sample output shows that the backup is in standby mode for the show l2vpn xconnect detail command:

RP/0/RSP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is up; Interworking none
  Monitor-Session: pw-span-test, state is configured
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: send 90
      byte totals: send 19056
  PW: neighbor 10.1.1.1, PW ID 1, state is up ( established )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          16003                         
      Group ID     0x5000300                      0x5000400                     
      Interface    GigabitEthernet0/4/0/1         GigabitEthernet0/4/0/2 
       Interface   pw-span-test                 GigabitEthernet0/3/0/1 
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:07 (00:49:18 ago)
    Last time status changed: 20/11/2007 21:45:11 (00:49:14 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

  Backup PW:
  PW: neighbor 2.2.2.2, PW ID 2, state is up ( established )
    Backup for neighbor 1.1.1.1 PW ID 1 ( standby )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 10.1.1.1 PW ID 1
    Create time: 20/11/2007 21:45:45 (00:48:40 ago)
    Last time status changed: 20/11/2007 21:45:49 (00:48:36 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

The following sample output shows that the backup is active for the show l2vpn xconnect detail command:

RP/0/RSP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is down; Interworking none
  Monitor-Session: pw-span-test, state is configured
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: send 98
      byte totals: send 20798
  PW: neighbor 10.1.1.1, PW ID 1, state is down ( local ready )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          unknown                       
      Group ID     0x5000300                      0x0                           
      Interface    GigabitEthernet0/4/0/1         unknown   
       Interface     pw-span-test                      GigabitEthernet0/3/0/1
      MTU          1500                           unknown                       
      Control word enabled                        unknown                       
      PW type      Ethernet                       unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x3                            0x0                           
                                                  (none)                        
                    (control word)                                               
                   (router alert label)                                         
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:06 (00:53:31 ago)
    Last time status changed: 20/11/2007 22:38:14 (00:00:23 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

  Backup PW:
  PW: neighbor 10.2.2.2, PW ID 2, state is up ( established )
    Backup for neighbor 10.1.1.1 PW ID 1 ( active )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 10.1.1.1 PW ID 1
    Create time: 20/11/2007 21:45:44 (00:52:54 ago)
    Last time status changed: 20/11/2007 21:45:48 (00:52:49 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

The following sample output displays the xconnects with switch port analyzer (SPAN) as one of the segments:

Show l2vpn xconnect type minotor-session-pw
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
        LU = Local Up, RU = Remote Up, CO = Connected

XConnect                         Segment 1                    Segment 2                
Group             Name       ST     Description           ST   Description            ST
-----------------------------   ---------------------------  --------------------------
g1                x1        UP    pw-span-test          UP   2.2.2.2         1      UP
--------------------------------------------------------------------------------------

The following sample output shows that one-way redundancy is enabled:

Group g1, XC x2, state is up; Interworking none
  AC: GigabitEthernet0/2/0/0.2, state is up, active in RG-ID 1
    Type VLAN; Num Ranges: 1
    VLAN ranges: [2, 2]
    MTU 1500; XC ID 0x3000002; interworking none
    Statistics:
      packets: received 103, sent 103
      bytes: received 7348, sent 7348
      drops: illegal VLAN 0, illegal length 0
  PW: neighbor 101.101.101.101, PW ID 2000, state is up ( established )
    PW class class1, XC ID 0x3000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet VLAN, control word disabled, interworking none
PW backup disable delay 0 sec
One-way PW redundancy mode is enabled
    Sequencing not set
…..
    Incoming Status (PW Status TLV):
      Status code: 0x0 (Up) in Notification message
    Outgoing Status (PW Status TLV):
      Status code: 0x0 (Up) in Notification message
…..
  Backup PW:
  PW: neighbor 102.102.102.102, PW ID 3000, state is standby ( all ready )
    Backup for neighbor 101.101.101.101 PW ID 2000 ( inactive )
    PW class class1, XC ID 0x3000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet VLAN, control word disabled, interworking none
    Sequencing not set
…..
    Incoming Status (PW Status TLV):
      Status code: 0x26 (Standby, AC Down) in Notification message
    Outgoing Status (PW Status TLV):
      Status code: 0x0 (Up) in Notification message

The following example shows sample output for the show l2vpn xconnect command:

RP/0/RSP0/CPU0:router# show l2vpn xconnect

Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
              LU = Local Up, RU = Remote Up, CO = Connected

XConnect                   Segment 1                   Segment 2                
Group      Name       ST   Description            ST   Description            ST
----------------------------   ---------------------------   -------------------------
siva_xc    siva_p2p   UP   Gi0/4/0/1              UP   1.1.1.1         1      UP
                                                       Backup                   
                                                       2.2.2.2         2      UP
--------------------------------------------------------------------------------

The following sample output shows that the backup is in standby mode for the show l2vpn xconnect detail command:

RP/0/RSP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is up; Interworking none
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: received 90, sent 90
      byte totals: received 19056, sent 19056
  PW: neighbor 1.1.1.1, PW ID 1, state is up ( established )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          16003                         
      Group ID     0x5000300                      0x5000400                     
      Interface    GigabitEthernet0/4/0/1         GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:07 (00:49:18 ago)
    Last time status changed: 20/11/2007 21:45:11 (00:49:14 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

  Backup PW:
  PW: neighbor 2.2.2.2, PW ID 2, state is up ( established )
    Backup for neighbor 1.1.1.1 PW ID 1 ( standby )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 1.1.1.1 PW ID 1
    Create time: 20/11/2007 21:45:45 (00:48:40 ago)
    Last time status changed: 20/11/2007 21:45:49 (00:48:36 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

The following sample output shows that the backup is active for the show l2vpn xconnect detail command:

RP/0/RSP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is down; Interworking none
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: send 98
      byte totals: send 20798
  PW: neighbor 1.1.1.1, PW ID 1, state is down ( local ready )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          unknown                       
      Group ID     0x5000300                      0x0                           
      Interface    GigabitEthernet0/4/0/1         unknown                       
      MTU          1500                           unknown                       
      Control word enabled                        unknown                       
      PW type      Ethernet                       unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x3                            0x0                           
                                                  (none)                        
                    (control word)                                               
                   (router alert label)                                         
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:06 (00:53:31 ago)
    Last time status changed: 20/11/2007 22:38:14 (00:00:23 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

  Backup PW:
  PW: neighbor 2.2.2.2, PW ID 2, state is up ( established )
    Backup for neighbor 1.1.1.1 PW ID 1 ( active )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 1.1.1.1 PW ID 1
    Create time: 20/11/2007 21:45:44 (00:52:54 ago)
    Last time status changed: 20/11/2007 21:45:48 (00:52:49 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

This example shows that the PW type changes to Ethernet, which is Virtual Circuit (VC) type 5, on the interface when a double tag rewrite option is used.
RP/0/RSP0/CPU0:router# show l2vpn xconnect pw-class pw-class1 detail

Group VPWS, XC ac3, state is up; Interworking none
AC: GigabitEthernet0/7/0/5.3, state is up
Type VLAN; Num Ranges: 1
VLAN ranges: [12, 12]
MTU 1508; XC ID 0x2440096; interworking none
Statistics:
packets: received 26392092, sent 1336
bytes: received 1583525520, sent 297928
drops: illegal VLAN 0, illegal length 0
PW: neighbor 3.3.3.3, PW ID 3, state is up ( established )
PW class VPWS1, XC ID 0x2440096
Encapsulation MPLS, protocol LDP
PW type Ethernet, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set

Preferred path tunnel TE 3, fallback disabled
PW Status TLV in use
						MPLS         Local                          Remote
						------------ ------------------------------ -----------------------------
						Label        16147                          21355
						Group ID     0x120001c0                     0x120001c0
      Interface    GigabitEthernet0/7/0/5.3       GigabitEthernet0/7/0/5.3
      MTU          1508                           1508
      Control word disabled                       disabled
      PW type      Ethernet                       Ethernet                    
      VCCV CV type 0x2                            0x2
                   (LSP ping verification)        (LSP ping verification)
      VCCV CC type 0x6                            0x6
                   (router alert label)           (router alert label)
                   (TTL expiry)                   (TTL expiry)
      ------------ ------------------------------ -----------------------------
Incoming Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Outgoing Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
MIB cpwVcIndex: 4294705365
Create time: 21/09/2011 08:05:01 (00:14:01 ago)
Last time status changed: 21/09/2011 08:07:01 (00:12:01 ago)
Statistics:
packets: received 1336, sent 26392092
bytes: received 297928, sent 1583525520

This example shows the sample output of a pseudowire headend (PWHE) cross connect:
RP/0/RSP0/CPU0:router#  show l2vpn xconnect interface pw-ether 67 detail
Group g1, XC xc1, state is down; Interworking none
  AC:PW-Ether1, state is up
    Type PW-Ether 
    Interface-list: interfacelist1
    Replicate status:
      Gi0/2/0/1: success 
      Gi0/3/0/1: pending
      Gi0/4/0/1: failed
    MTU 1500; interworking none
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  PW: neighbor 130.130.130.130, PW ID 1234, state is down ( provisioned )
    PW class not set
    Encapsulation MPLS, protocol LDP
    PW type Ethernet VLAN, control word disabled, interworking none
    Sequencing not set
    Internal label: 16008
    VLAN id imposed: 101

      MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        16001                          unknown                       
      Group ID     0x2000600                      0x0                           
      Interface    PW-Ether1       				   unknown                       
      MTU          1500                           unknown                       
      Control word disabled                       unknown                       
      PW type      Ethernet VLAN                  unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x6                            0x0                           
                                                  (none)                        
                   (router alert label)                                         
                   (TTL expiry)                                                 
      ------------ ------------------------------ -----------------------------
    MIB cpwVcIndex: 2
    Create time: 19/02/2010 23:13:01 (1w2d ago)
    Last time status changed: 19/02/2010 23:13:16 (1w2d ago)
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
This example shows the sample output of a configured flow label:
RP/0/RSP0/CPU0:router#  show l2vpn xconnect detail
Group g1, XC p1, state is up; Interworking none
  AC: GigabitEthernet0/0/1/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x1000002; interworking none
    Statistics:
      packets: received 24688, sent 24686
      bytes: received 1488097, sent 1487926
  PW: neighbor 3.3.3.3, PW ID 2, state is up ( established )
    PW class class1, XC ID 0x1000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word disabled, interworking none
    PW backup disable delay 0 sec
Sequencing not set
Flow label flags configured (Rx=1,Tx=1), negotiated (Rx=0,Tx=1)

This table describes the significant fields shown in the display.

Table 4 show l2vpn xconnect Command Field Descriptions

Field

Description

XConnect Group

Displays a list of all configured cross-connect groups.

Group

Displays the cross-connect group number.

Name

Displays the cross-connect group name.

Description

Displays the cross-connect group description. If no description is configured, the interface type is displayed.

ST

State of the cross-connect group: up (UP) or down (DN).

This example shows the output of the show l2vpn xconnect command with IPv6 addresses listed:
RP/0/RSP0/CPU0:router# show l2vpn xconnect

Fri May 18 10:25:48.279 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc1 DN Gi0/0/0/4.3 UP 1.2.3.4 1 DN
----------------------------------------------------------------------------------------
g1 xc2 UR Gi0/0/0/4.1 DN 1 UR
aaaa:bbbb::cdef
----------------------------------------------------------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
g1 xc4 UR Gi0/0/0/4.4 DN 1 UR
1111:3333::4444
----------------------------------------------------------------------------------------

This example shows the output of the show l2vpn xconnect interface command:
RP/0/RSP0/CPU0:router# show l2vpn xconnect interface Gi0/0/0/4.4 detail

Fri May 18 10:34:28.263 EDT
Group g1, XC xc4, state is unresolved; Interworking none
Not provisioned reason(s):
IPv6 not supported for this service
AC: GigabitEthernet0/0/0/4.4, state is down (Segment-down)
Type VLAN; Num Ranges: 1
VLAN ranges: [4, 4]
MTU 1500; XC ID 0x4; interworking none
PW: neighbor 1111:3333::4444, PW ID 1, state is unresolved

This example shows the output of the show running-config l2vpn xconnect group command with IPv6 neighbor information:
RP/0/RSP0/CPU0:router# show running-config l2vpn xconnect group g1 p2p xc4

Fri May 18 10:35:51.734 EDT
l2vpn
xconnect group g1
p2p xc4
interface GigabitEthernet0/0/0/4.4
neighbor ipv6 1111:3333::4444 pw-id 1
!
This example shows the output of the show l2vpn xconnect neighbor ipv4 command:
RP/0/RSP0/CPU0:router# show l2vpn xconnect neighbor ipv4 1.2.3.4

Fri May 18 10:28:22.289 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc1 DN Gi0/0/0/4.3 UP 1.2.3.4 1 DN
----------------------------------------------------------------------------------------
This example shows the output of the show l2vpn xconnect neighbor ipv6 command:
RP/0/RSP0/CPU0:router# show l2vpn xconnect neighbor ipv6 1111:2222::cdef

Fri May 18 10:32:46.332 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
This example shows the output of the show l2vpn xconnect neighbor ipv6 command:
RP/0/RSP0/CPU0:router# show l2vpn xconnect neighbor ipv6 1111:2222::cdef

Fri May 18 10:32:46.332 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
RP/0/RSP0/CPU0:router# show l2vpn xconnect neighbor ipv6 1111:2222::cdef detail

Fri May 18 10:33:57.813 EDT
Group g1, XC xc3, state is up; Interworking none
AC: GigabitEthernet0/0/0/4.2, state is up
Type VLAN; Num Ranges: 1
VLAN ranges: [2, 2]
MTU 1500; XC ID 0x2; interworking none
Statistics:
packets: received 0, sent 0
bytes: received 0, sent 0
drops: MTU exceeded 0, other 0
PW: neighbor 1111:2222::cdef, PW ID 1, state is up
PW class ts, XC ID 0x2
Encapsulation L2TPv3, protocol none
Source address 1111:2222::abcd
PW type Ethernet VLAN, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
L2TP class not set, IPv6 source address 1111:2222::abcd
TOS 40 (reflect disabled), TTL 255, DF bit not set
Path MTU: disabled
L2TPv3 Local Remote
------------ ------------------------------ -----------------------------
Session 1 1
Cookie size 0 bytes 0 bytes
Cookie unassigned unassigned
------------ ------------------------------ -----------------------------
Create time: 18/05/2012 07:40:08 (04:12:49 ago)
Last time status changed: 18/05/2012 07:40:08 (04:12:49 ago)
Statistics:
packets: received 0, sent 0
bytes: received 0, sent 0
drops: out of sequence 0, other 0
This example shows the output of the show l2vpn xconnect state commands:
RP/0/RSP0/CPU0:router# show l2vpn xconnect state up

Fri May 18 10:36:45.913 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc3 UP Gi0/0/0/4.2 UP 1 UP
1111:2222::cdef
----------------------------------------------------------------------------------------
RP/0/RSP0/CPU0:router# show l2vpn xconnect state down

Fri May 18 10:37:25.113 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc1 DN Gi0/0/0/4.3 UP 1.2.3.4 1 DN
----------------------------------------------------------------------------------------
RP/0/RSP0/CPU0:router# show l2vpn xconnect state unresolved

Fri May 18 10:37:30.610 EDT
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready, (PP) = Partially Programmed
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------ ----------------------------- ---------------------------------------
g1 xc2 UR Gi0/0/0/4.1 DN 1 UR
aaaa:bbbb::cdef
----------------------------------------------------------------------------------------
g1 xc4 UR Gi0/0/0/4.4 DN 1 UR
1111:3333::4444
----------------------------------------------------------------------------------------

Related Commands

Command

Description

xconnect group

Configures cross-connect groups.  

source (p2p)

To configure source IPv6 address of the pseudowire, use the source command in p2p pseudowire configuration mode. To disable the source IPv6 address configuration, use the no form of this command.

source ipv6_address

no source ipv6_address

Syntax Description

ipv6_address

Source IPv6 address of pseudowire

Command Default

None

Command Modes

p2p pseudowire configuration

Command History

Release Modification
Release 4.3.1

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to set a source IPv6 address to a point-to-point IPv6 cross-connect:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group g1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p xc3
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# interface GigabitEthernet0/0/0/4.2
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)# source 1111:2222::abcd

Related Commands

Command

Description

p2p

Enters p2p configuration submode to configure point-to-point cross-connects.  

neighbor (L2VPN)

Configures a pseudowire for a cross-connect.  

tag-impose

To specify a tag for a VLAN ID configuration, use the tag-impose command in l2vpn configuration submode. To remove the tag, use the no form of this command.

tag-impose vlan value

no tag-impose vlan value

Syntax Description

vlan

VLAN in tagged mode.

value

Tag value. The range is from 1 to 4094. The default value is 0.

Command Default

None

Command Modes

L2VPN configuration

Command History

Release

Modification

Release 4.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to specify a tag for a VLAN:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group xc1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)#p2p grp1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)#neighbor 10.1.1.2 pw-id 78
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p-pw)#tag-impose vlan 8

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

tos (l2vpn)

To configure Type of Service (TOS) reflection or to set TOS value, use the tos command in L2VPN pseudowire class encapsulation L2TPv3 configuration mode. To reset the TOS value, use the no form of this command.

tos { reflect [ value tos value ] | value tos value [ reflect ] }

no tos { reflect [ value tos value ] | value tos value [ reflect ] }

Syntax Description

reflect

Enables TOS reflection.

value

Sets the TOS value for L2TPv3 pseudowire class.

tos value

Value of the TOS.

Command Default

By default, the TOS is copied over, from the class of service (COS) fields of the VLAN header. If the underlying packet is not an IPv4 or IPv6 packet, the COS fields are copied from the VLAN header, even if TOS reflection is configured.

Command Modes

L2VPN pseudowire class encapsulation L2TPv3 configuration

Command History

Release Modification
Release 4.3.1

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to configure TOS reflection:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# tos reflect

The following example shows how to set a TOS value:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# tos value 64

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

pw-class encapsulation l2tpv3

Configures L2TPv3 pseudowire encapsulation.  

transport mode (L2VPN)

To configure L2VPN pseudowire class transport mode, use the transport mode command in L2VPN pseudowire class MPLS encapsulation mode. To disable the L@VPN pseudowire class transport mode configuration, use the no form of this command.

transport mode { ethernet | vlan passthrough }

no transport mode { ethernet | vlan passthrough }

Syntax Description

ethernet

Configures Ethernet port mode.

vlan

Configures VLAN tagged mode.

passthrough

Enables the pseudowires to pass through the incoming tags.

Command Default

None

Command Modes

L2VPN pseudowire class MPLS encapsulation

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.1.0

The variable passthrough was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to configure Ethernet transport mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pw)# encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-encap-mpls)# transport-mode ethernet

Examples

The following example shows how to configure pseudowires in a VLAN tagged mode with the passthrough variable:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class pwc1
RP/0/RSP0/CPU0:router(config-l2vpn-pw)# encapsulation mpls
RP/0/RSP0/CPU0:router(config-l2vpn-encap-mpls)# transport-mode vlan passthrough

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

transport mode vlan passthrough

To configure L2VPN bridge domain transport mode, use the transport mode vlan passthrough command in L2VPN bridge domain configuration mode. To disable the L2VPN bridge domain transport mode configuration, use the no form of this command.

transport mode vlan passthrough

no transport mode vlan passthrough

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN bridge domain configuration

Command History

Release

Modification

Release 4.3.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

This example shows how to configure transport mode vlan passthrough:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group bg1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bd1
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# transport mode vlan passthrough

Related Commands

Command

Description

bridge-domain (VPLS)

Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.  

ttl (l2vpn)

To configure Time to Live (TTL) for Pseudowire class, use the ttl command in L2VPN pseudowire class encapsulation L2TPv3 configuration mode. To disable the TTL configuration, use the no form of this command.

ttl ttl _value

no ttl ttl_value

Syntax Description

ttl_value

The TTL Value. Range is from 1 to 255.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation L2TPv3 configuration

Command History

Release Modification
Release 4.3.1

This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


All L2VPN configurations can be deleted using the no l2vpn command.


Task ID

Task ID Operation

l2vpn

read, write

Examples

This example shows how to configure TTL:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RSP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3
RP/0/RSP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# ttl 40

Related Commands

Command

Description

pw-class (L2VPN)

Enters pseudowire class submode to define a pseudowire class template.  

pw-class encapsulation l2tpv3

Configures L2TPv3 pseudowire encapsulation.  

xconnect group

To configure cross-connect groups, use the xconnect group command in L2VPN configuration mode. To return to the default behavior, use the no form of this command.

xconnect group group-name

no xconnect group group-name

Syntax Description

group-name

Configures a cross-connect group name using a free-format 32-character string.

Command Default

None

Command Modes

L2VPN configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


You can configure up to a maximum of 16K cross-connects per box.


Task ID

Task ID

Operations

l2vpn

read, write

Examples

The following example shows how to group all cross -connects for customer_atlantic:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group customer_atlantic

Related Commands

Command

Description

show l2vpn xconnect

Displays brief information on configured cross-connects.