Cisco ASR 9000 Series Aggregation Services Router IP Addresses and Services Command Reference, Release 4.3.x
LPTS Commands
Downloads: This chapterpdf (PDF - 1.6MB) The complete bookPDF (PDF - 6.93MB) | Feedback

LPTS Commands

LPTS Commands

This chapter describes the Cisco IOS XR software commands used to monitor Local Packet Transport Services (LPTS) on the Cisco ASR 9000 Series Aggregation Services Router.

For detailed information about LPTS concepts, configuration tasks, and examples, refer to the Cisco ASR 9000 Series Aggregation Services Router IP Addresses and Services Configuration Guide.

clear lpts ifib statistics

To clear the Internal Forwarding Information Base (IFIB) statistics, use the clear lpts ifib statistics command in EXEC mode.

clear lpts ifib statistics [ location node-id ]

Syntax Description

location node-id

(Optional) Clears the IFIB statistics for the designated node. The node-id argument is entered in standard rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If you do not specify a node with the location keyword and node-id argument, the clear lpts ifib statistics command clears the IFIB statistics for the node on which the command is run.

Task ID

Task ID

Operations

lpts

execute

Examples

The following example shows how to clear the IFIB statistics for the RP:


RP/0/RSP0/CPU0:router# clear lpts ifib statistics
 

Related Commands

Command

Description

show lpts ifib statistics

Displays the LPTS IFIB statistics.

clear lpts pifib hardware statistics

To clear the Pre-Internal Forwarding Information Base (Pre-IFIB) hardware statistics, use the clear lpts pifib hardware statistics command in EXEC mode.

clear lpts pifib hardware statistics location node-id

Syntax Description

location node-id

Clears the Pre-IFIB hardware statistics for the designated node. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If you do not specify a node with the location keyword and node-id argument, this command clears the Pre-IFIB hardware statistics for the node on which the command is run.

Task ID

Task ID

Operations

lpts

execute

Examples

The following example shows how to display the sample output from the show lpts hardware police command and then clears the Pre-IFIB hardware statistics for the RP:


RP/0/RSP0/CPU0:router# show lpts pifib hardware police location 0/1/CPU0

-------------------------------------------------------------
                Node 0/1/CPU0:
-------------------------------------------------------------
 Burst = 100ms for all flow types 
-------------------------------------------------------------
FlowType               Policer Type    Cur. Rate  Def. Rate  Accepted             Dropped             
---------------------- ------- ------- ---------- ---------- -------------------- --------------------
unconfigured-default   100     Static  2500       2500       0                    0                   
Fragment               101     Static  2500       2500       0                    0                   
OSPF-mc-known          102     Static  1500       1500       0                    0                   
OSPF-mc-default        103     Static  2000       2000       0                    0                   
OSPF-uc-known          104     Static  1000       1000       0                    0                   
OSPF-uc-default        105     Static  2000       2000       0                    0                   
ISIS-known             143     Static  1500       1500       0                    0                   
ISIS-default           144     Static  2000       2000       0                    0                   
BGP-known              106     Static  1500       1500       0                    0                   
BGP-cfg-peer           107     Static  2000       2000       0                    0                   
BGP-default            108     Static  2500       2500       0                    0                   
PIM-mcast              109     Static  2000       2000       0                    0                   
PIM-ucast              110     Static  1500       1500       0                    0                   
IGMP                   111     Static  500        500        0                    0                   
ICMP-local             112     Static  1500       1500       0                    0                   
ICMP-app               112     Static  1500       1500       0                    0                   
na                     140     Static  1000       1000       0                    0                   
ICMP-default           112     Static  1500       1500       0                    0                   
LDP-TCP-known          113     Static  1500       1500       0                    0                 


RP/0/RSP0/CPU0:router# show lpts pifib hardware police location 0/2/CPU0


-------------------------------------------------------------
                Node 0/2/CPU0:
-------------------------------------------------------------
 Burst = 100ms for all flow types 
-------------------------------------------------------------
FlowType               Policer Type    Cur. Rate  Def. Rate  Accepted   Dropped   
---------------------- ------- ------- ---------- ---------- ---------- ----------
unconfigured-default   100     Static  500        500        0          0         
Fragment               106     Static  1000       1000       0          0         
OSPF-mc-known          107     Static  20000      20000      4285       0         
OSPF-mc-default        111     Static  5000       5000       1          0         
OSPF-uc-known          161     Static  5000       5000       0          0         
OSPF-uc-default        162     Static  1000       1000       0          0         
ISIS-known             108     Static  20000      20000      0          0         
ISIS-default           112     Static  5000       5000       0          0         
BGP-known              113     Static  25000      25000      891        0         
BGP-cfg-peer           114     Static  10000      10000      6          0         
BGP-default            115     Static  10000      10000      2          0         
PIM-mcast              116     Static  23000      23000      0          0         
PIM-ucast              117     Static  10000      10000      0          0         
IGMP                   118     Static  3500       3500       0          0         
ICMP-local             119     Static  2500       2500       0          0         
ICMP-app               120     Static  2500       2500       0          0 


RP/0/RSP0/CPU0:router# clear lpts pifib hardware statistics location 0/2/CPU0

Clear "show controllers statistics" counters on this location [confirm]

RP/0/RSP0/CPU0:router# show lpts pifib hardware police location 0/2/CPU0

-------------------------------------------------------------
                Node 0/2/CPU0:
-------------------------------------------------------------
 Burst = 100ms for all flow types 
-------------------------------------------------------------
FlowType               Policer Type    Cur. Rate  Def. Rate  Accepted   Dropped   
---------------------- ------- ------- ---------- ---------- ---------- ----------
unconfigured-default   100     Static  500        500        0          0         
Fragment               106     Static  1000       1000       0          0         
OSPF-mc-known          107     Static  20000      20000      14         0         
OSPF-mc-default        111     Static  5000       5000       0          0         
OSPF-uc-known          161     Static  5000       5000       0          0         
OSPF-uc-default        162     Static  1000       1000       0          0         
ISIS-known             108     Static  20000      20000      0          0         
ISIS-default           112     Static  5000       5000       0          0         
BGP-known              113     Static  25000      25000      1          0         
BGP-cfg-peer           114     Static  10000      10000      0          0         
BGP-default            115     Static  10000      10000      0          0         
PIM-mcast              116     Static  23000      23000      0          0         
PIM-ucast              117     Static  10000      10000      0          0         
IGMP                   118     Static  3500       3500       0          0         
ICMP-local             119     Static  2500       2500       0          0         
ICMP-app               120     Static  2500       2500       0          0 

Related Commands

Command

Description

show lpts pifib hardware police

Displays the policer configuration value set.

clear lpts pifib statistics

To clear the Pre-Internal Forwarding Information Base (Pre-IFIB) statistics, use the clear lpts pifib statistics command in EXEC mode.

clear lpts pifib statistics [ location node-id ]

Syntax Description

location node-id

Clears the Pre-IFIB statistics for the designated node. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If you do not specify a node with the location keyword and node-id argument, this command clears the Pre-IFIB statistics for the node on which the command is run.

Task ID

Task ID

Operations

lpts

execute

Examples

The following example shows how to clear the Pre-IFIB statistics for the RP:


RP/0/RSP0/CPU0:router# clear lpts pifib statistics

Related Commands

Command

Description

show lpts pifib statistics

Displays the LPTS PIFIB statistics.

flow (LPTS)

To configure the policer for the Local Packet Transport Services (LPTS) flow type, use the flow command in pifib policer global configuration mode or pifib policer per-node configuration mode. To disable this feature, use the no form of this command.

flow flow-type rate rate

no flow flow-type rate rate

Syntax Description

flow-type

List of supported flow types.

rate rate

Specifies the rate in packets per seconds (PPS). The range is from 0 to 4294967295.

Command Default

The default behavior is to load the policer values from the static configuration file that is platform dependant.

Command Modes

Pifib policer global configuration

Pifib policer per-node configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The table lists the supported flow types and the parameters that are used to define a policer.

This table lists the supported flow types and the parameters that are used to define a policer.

Table 1 List of Supported Flow Types

Flow Type

Description

Default Packet Rate (Recommended)

all-routers

Packets sent to all-routers multicast addresses, which include multicast LDP UDP packet.

1000

bgp-cfg-peer

Packets from a configured BGP peer.

2000

bgp-default

Packets from unconfigured, newly configured, or wildcard BGP peers.

2500

bgp-known

Packets from established BGP peering sessions.

1500

css-default

Packets from a new or newly established CSS session.

200

css-known

Packets from an established CSS session.

200

default-flow

Default flow type.

2500

eigrp

EIGRP packets for configured interfaces.

1500

gre

Generic Routing Encapsulation packets

1000

fragment

Fragmented packets.

2500

http-default

Packets from a new or newly established HTTP session.

400

http-known

Packets from an established HTTP session.

200

icmp-app

ICMP or ICMPv6 packets of interest to applications.

1500

icmp-default

Other ICMP or ICMPv6 packets.

1500

icmp-local

ICMP or ICMPv6 packets with local interest.

1500

igmp

IGMP packets.

500

ike

IKE packets.

100

ipsec-default

AH or ESP packets with unknown or newly configured SPIs.

100

ipsec-known

AH or ESP packets with known SPIs.

400

ip-sla

IP SLA packets (this is a hidden flow type)

1000

isis-default

IS-IS packets for unconfigured (or newly, configured) interfaces.

2000

isis-known

IS-IS packets for configured interfaces.

1500

ldp-tcp-cfg-peer

Packets from a configured LDP TCP peer (SYNs or newly, established sessions).

2000

ldp-tcp-default

Packets from an unconfigured, newly configured, or wildcard LDP TCP peer.

2500

ldp-tcp-known

Packets from an established LDP peering session.

1500

ldp-udp

Unicast LDP UPD packets.

2000

lmp-tcp-cfg-peer

Packets from a configured LMP TCP peer (SYNs or newly established sessions).

2000

lmp-tcp-default

Packets from an unconfigured, newly configured, or wild-card LMP TCP peer.

2500

lmp-tcp-known

Packets from an established LMP peering session.

1500

lmp-udp

Unicast LMP UDP packets.

2000

msdp-cfg-peer

Packets from a configured MSDP peer.

200

msdp-default

Packets from an unconfigured, newly configured, or wildcard MSDP peer.

300

msdp-known

Packets from an established MSDP session.

100

multicast-default

Packets for unconfigured or newly configured multicast groups.

2500

multicast-known

Packets for configured multicast groups.

2000

ntp-known

Packets from an established NTP session.

500

ntp-default

Packets from a new or newly established NTP session.

500

ospf-mc_default

OSPF multicast packets for unconfigured (or newly configured) interfaces.

2000

ospf-mc-known

OSPF multicast packets for configured interfaces.

1500

ospf-uc-default

OSPF unicast packets for unconfigured (or newly configured) interfaces.

2000

ospf-uc-known

OSPF unicast packets for configured interfaces.

1000

pim-multicast

PIM multicast packets.

2000

pim-unicast

PIM unicast packets.

1500

rip

RIP packets.

1500

rsh-default

Packets from a new or newly established RSH session.

200

rsh-known

Packets from an established RSH session.

200

rsvp

RSVP packets.

2000

rsvp-udp

RSVP UDP packets.

2000

raw-default

Packets for unconfigured or newly configured IPv4 or IPv6 protocols.

2500

raw-listen

Packets for configured IP protocols.

2500

shttp-default

Packets from a new or newly established SSHTP session.

400

shttp-known

Packets from an established SHTTP session.

200

snmp

SNMP packets.

300

ssh-default

Packets from a new or newly established SSH session.

300

ssh-known

Packets from an established SSH session.

200

tcp-cfg-peer

Packets for configured TCP peers.

2000

tcp-default

Packets for unconfigured or newly configured TCP services.

2500

tcp-known

Packets for established TCP sessions.

2000

tcp-listen

Packets for configured TCP services.

2500

telnet-default

Packets from a new or newly established Telnet session.

200

telnet-known

Packets from an established Telnet session.

200

udp-cfg-peer

Packets for configured UDP-based protocol sessions.

2500

udp-default

Packets for unconfigured or newly configured UDP services.

2500

udp-known

Packets for established UDP sessions.

2000

udp-listen

Packets for configured UDP services.

2500

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to configure the LPTS policer for the bgp-known flow type for all line cards:


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# lpts pifib hardware police
RP/0/RSP0/CPU0:router(config-pifib-policer-global)# flow bgp-known rate 20000

The following example shows how to configure LPTS policer for the Intermediate System-to-Intermediate System (IS-IS)-known flow type for a specific line card:


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:routerconfig)# lpts pifib hardware police location 0/2/CPU0
RP/0/RSP0/CPU0:router(config-pifib-policer-per-node)# flow isis-known rate 22222

lpts pifib hardware police

To configure the ingress policers and to enter pifib policer global configuration mode or pifib policer per-node configuration mode, use the lpts pifib hardware police command in global configuration mode. To set the policer to the default value, use the no form of this command.

lpts pifib hardware police [ location node-id ] [ flow flow-type { default | known } [ rate rate ] [ precedence { number | name} ] ]

no lpts pifib hardware police [ location node-id ] [ flow flow-type { default | known } [ rate rate ] [ precedence { number | name} ] ]

Syntax Description

location node-id

(Optional) Designated node. The node-id argument is entered in the rack/slot/module notation.

flow flow-type rate rate

Lpts flow type and the policer rate in packets per second (PPS).

default

Indicates generic flows which are policed with default-rate. For example, BGP (*, 179), any packet with port:179 policed with default rate.

known

Indicates specific flows which are policed with known-rate.

precedence {number |name}

Sets Type of Service (TOS) precedence value. You can specify either a precedence number or name. The range of argument number is between 0 to 7.

The name argument has following keywords:

  • routine—Match packets with routine precedence ( 0)
  • priority—Match packets with priority precedence (1)
  • immediate—Match packets with immediate precedence (2)
  • flash—Match packets with flash precedence (3)
  • flash-override—Match packets with flash override precedence (4)
  • critical—Match packets with critical precedence (5)
  • internet—Match packets with internetwork control precedence (6)
  • network—Match packets with network control precedence (7)

Command Modes

Global configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.2.0

New flow types such as dns, radius, tacacs, ntp known, rsvp known and pim multicast known flow types were added.

Release 4.3.1

The precedence keyword was added.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

You can configure the IP precedence for a specific node or globally for all nodes.

Task ID

Task ID

Operations

lpts

read, write

config-services

read, write

Examples

This example shows how to configure the lpts pifib hardware police command for all line cards:


RP/0/RSP0/CPU0:router(config)# lpts pifib hardware police
RP/0/RSP0/CPU0:router(config-pifib-policer-global)#

This example shows how to configure the lpts pifib hardware police command for a specific line card:


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# lpts pifib hardware police location 0/2/CPU0 flow dns rate 10

This example shows how to configure the TOS precedence globally (applies to all line cards at once) using the lpts pifib hardware police command:
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# lpts pifib hardware police flow telnet default precedence internet network 

This example shows how to configure the TOS precedence for the 0/2/CPU0 location using the lpts pifib hardware police command:
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# lpts pifib hardware police location 0/2/CPU0 flow telnet default precedence 5 3 6

Related Commands

Command

Description

flow (LPTS)

Configures the policer for the LPTS flow type.

show lpts pifib hardware police

Displays the policer configuration value set.

show lpts bindings

To display the binding information in the Port Arbitrator, use the show lpts bindings command in EXEC mode.

show lpts bindings [ location node-id ] [ client-id { clnl | ipsec | ipv4-io | ipv6-io | mpa | tcp | test | udp | raw } ] [brief] [ vrf vrf-name ]

Syntax Description

location node-id

(Optional) Displays information for the specified node. The node-id argument is entered in the rack/slot/module notation.

client-id

(Optional) Type of client. It can be one of the following values:

  • clnl —ISO connectionless protocol (used by IS-IS)
  • ipsec —Secure IP
  • ipv4-io —Traffic processed by the IPv4 stack
  • ipv6-io —Traffic processed by the IPv6 stack
  • mpa —Multicast Port Arbitrator (multicast group joins)
  • tcp —Transmission Control Protocol
  • test —Test applications
  • udp —User Datagram Protocol
  • raw —Raw IP

brief

(Optional) Displays summary output.

vrf vrf-name

(Optional) Name of assigned VRF.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show lpts bindings command displays the Local Packet Transport Services (LPTS) bindings (requests to receive traffic of a particular type). Bindings are aggregated into flows by the LPTS Port Arbitrator; flows are then programmed into the Internal Forwarding Information Base (IFIB) and Pre-IFIB to direct packets to applications.

If you specify the optional client-id keyword and type of client, only bindings from that client are shown. If you specify the optional location keyword and node-id argument, only bindings from clients on that node are displayed.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts bindings command, displaying bindings for all client ID types:

RP/0/RSP0/CPU0:router# show lpts bindings

@ - Indirect binding; Sc - Scope

------------------------------------------
Location   :0/1/CPU0
Client ID  :IPV4_IO
Cookie     :0x00000001
Clnt Flags :
Layer 3    :IPV4
Layer 4    :ICMP
Local Addr :any
Remote Addr:any
Local Port :any
Remote Port:any
Filters    :Type / Intf or Pkt Type / Source Addr / Location
 INCLUDE_TYPE / type 8
 INCLUDE_TYPE / type 13
 INCLUDE_TYPE / type 17
------------------------------------------
Location   :0/2/CPU0
Client ID  :IPV4_IO
Cookie     :0x00000001
Clnt Flags :
Layer 3    :IPV4
Layer 4    :ICMP
Local Addr :any
Remote Addr:any
Local Port :any
Remote Port:any
Filters    :Type / Intf or Pkt Type / Source Addr / Location
 INCLUDE_TYPE / type 8
 INCLUDE_TYPE / type 13
 INCLUDE_TYPE / type 17
------------------------------------------
Location   :0/RP1/CPU0
Client ID  :TCP
Cookie     :0x4826f1f8
Clnt Flags :REUSEPORT
Layer 3    :IPV4
Layer 4    :TCP
Local Addr :any
Remote Addr:any
Local Port :7
Remote Port:any
------------------------------------------
Location   :0/RP1/CPU0
Client ID  :TCP
Cookie     :0x4826fa0c
Clnt Flags :REUSEPORT
Layer 3    :IPV4
Layer 4    :TCP
Local Addr :any
Remote Addr:any
Local Port :9
Remote Port:any
------------------------------------------
Location   :0/RP1/CPU0
Client ID  :TCP
Cookie     :0x482700d0
Clnt Flags :REUSEPORT
Layer 3    :IPV4
Layer 4    :TCP
Local Addr :any
Remote Addr:any
Local Port :19
Remote Port:any
------------------------------------------
Location   :0/RP1/CPU0
Client ID  :IPV4_IO
Cookie     :0x00000001
Clnt Flags :
Layer 3    :IPV4
Layer 4    :ICMP
Local Addr :any
Remote Addr:any
Local Port :any
Remote Port:any
Filters    :Type / Intf or Pkt Type / Source Addr / Location
 INCLUDE_TYPE / type 8
 INCLUDE_TYPE / type 13
 INCLUDE_TYPE / type 17

This table describes the significant fields shown in the display.



Table 2 show lpts bindings Command Field Descriptions

Field

Description

Location

Node location, in the format of rack/slot/module.

Client ID

LPTS client type.

Cookie

Client’s unique tag for the binding.

Clnt Flags

REUSEPORT -- client has set the SO_REUSEPORT or SO_REUSEADDR socket option.

Layer 3

Layer 3 protocol (IPv4, IPv6, CLNL).

Layer 4

Layer 4 protocol (TCP, UDP).

Local Addr

Local (destination) address.

Remote Addr

Remote (source) address.

Local Port

Local (destination) TCP or UDP port, or ICMP/IGMP packet type, or IPsec SPI.

Remote Port

Remote (source) TCP or UDP port.

The following sample output is from the show lpts bindings brief command:

RP/0/RSP0/CPU0:router# show lpts bindings brief

@ - Indirect binding; Sc - Scope

 Location   Clnt Sc L3   L4    VRF-ID   Local,Remote Address.Port  Interface
 ---------- ---- -- ---- ----- -------- -------------------------- ------------
 0/1/CPU0   IPV4 LO IPV4 ICMP  *        any.ECHO any               any         
 0/1/CPU0   IPV4 LO IPV4 ICMP  *        any.TSTAMP any             any         
 0/1/CPU0   IPV4 LO IPV4 ICMP  *        any.MASKREQ any            any         
 0/1/CPU0   IPV6 LO IPV6 ICMP6 *        any.ECHOREQ any            any         
 0/3/CPU0   IPV4 LO IPV4 ICMP  *        any.ECHO any               any         
 0/3/CPU0   IPV4 LO IPV4 ICMP  *        any.TSTAMP any             any       

This table describes the significant fields shown in the display.



Table 3 show lpts bindings brief Command Field Descriptions

Field

Description

Location

Node location, in the format of rack/slot/module.

Clnt ID

LPTS client type.

Sc

Scope (LR = Logical-Router, LO = Local).

Layer 3

Layer 3 protocol.

Layer 4

Layer 4 protocol.

VRF-ID

VPN routing and forwarding (VRF) identification (vrfid) number.

Local,Remote Address.Port

Local (destination) and Remote (source) addresses and ports or packet types.

Interface

Inbound interface.

Related Commands

Command

Description

show lpts clients

Displays the client information for the Port Arbitrator.

show lpts flows

Displays information about LPTS flows.

show lpts clients

To display the client information for the Port Arbitrator, use the show lpts clients command in EXEC mode.

show lpts clients [times]

Syntax Description

times

(Optional) Displays information about binding request rates and service times.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show lpts clients command displays the clients connected to the local packet transport services (LPTS) port arbitrator (PA).

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts clients command:

RP/0/RSP0/CPU0:router# show lpts clients

o_flgs - open flags ; clid - client id
clid            loc             flags   o_flgs
RAW(3)          0/RP1/CPU0      0x1     0x2
TCP(1)          0/RP1/CPU0      0x1     0x2
IPV4_IO(5)      0/1/CPU0        0x3     0x2
IPV4_IO(5)      0/2/CPU0        0x3     0x2
IPV4_IO(5)      0/RP1/CPU0      0x3     0x2
MPA(7)          0/RP1/CPU0      0x3     0x0

This table describes the significant fields shown in the display.



Table 4 show lpts clients Command Field Descriptions

Field

Description

Clid

LPTS client ID.

Loc

Node location, in the format rack/slot/module.

Flags

Client flags.

Note   

The client flags are used only for debugging purposes.

o_flags

Open flags.

Note   

The open flags are used only for debugging purposes.

The following sample output is from the show lpts clients times command. The output shows samples for the last 30 seconds, 1 minute, 5 minutes, 10 minutes, and a total (if nonzero). The number of transactions, number of updates, and the minimum/average/maximum time in milliseconds to process each transaction is shown.

RP/0/RSP0/CPU0:router# show lpts clients times

o_flgs - open flags ; clid - client id
clid            loc     flags   o_flgs
RAW(3)          0/RP1/CPU0      0x1     0x2
   30s:2 tx 2 upd 2/2/3ms/tx
    1m:2 tx 2 upd 2/2/3ms/tx
    5m:2 tx 2 upd 2/2/3ms/tx
   10m:2 tx 2 upd 2/2/3ms/tx
 total:2 tx 2 upd 2/-/3ms/tx
TCP(1)          0/RP1/CPU0      0x1     0x2
 total:3 tx 3 upd 1/-/1ms/tx
IPV4_IO(5)      0/1/CPU0        0x3     0x2
 total:1 tx 1 upd 0/-/0ms/tx
IPV4_IO(5)      0/2/CPU0        0x3     0x2
 total:1 tx 1 upd 1/-/1ms/tx
IPV4_IO(5)      0/RP1/CPU0      0x3     0x2
 total:1 tx 1 upd 3/-/3ms/tx
MPA(7)          0/RP1/CPU0      0x3     0x0

Related Commands

Command

Description

show lpts bindings

Displays the binding information in the port arbitrator.

show lpts flows

Displays information about LPTS flows.

show lpts flows

To display information about Local Packet Transport Services (LPTS) flows, use the show lpts flows command in EXEC mode.

show lpts flows [brief]

Syntax Description

brief

(Optional) Displays summary output.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show lpts flows command is used to display LPTS flows, which are aggregations of identical binding requests from multiple clients and are used to program the LPTS Internal Forwarding Information Base (IFIB) and Pre-IFIB.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts flows command:

RP/0/RSP0/CPU0:router# show lpts flows

------------------------------------------
L3-proto    : IPV4(2)
L4-proto    : ICMP(1)
VRF-ID      : * (000000000)
Local-IP    : any
Remote-IP   : any
Pkt-Type    : 8
Remote-Port : any
Interface   : any (0x0)
Flow-type   : ICMP-local
Min-TTL     : 0
Slice       : RAWIP4_FM
Flags       : 0x20 (in Pre-IFIB)
Location    : (drop)
Element References
location / count / scope
* / 3 / LOCAL

This table describes the significant fields shown in the display.



Table 5 show lpts flows Command Field Descriptions

Field

Description

L3-proto

Layer 3 protocol (IPv4, IPv6, CLNL).

L4-proto

Layer 4 protocol (TCP, UDP, and so on).

VRF-ID

VPN routing and forwarding (VRF) identification (vrfid) number.

Local-IP

Local (destination) IP address.

Remote-IP

Remote (source) IP address.

Pkt-Type

ICMP or IGMP packet type.

Remote-Port

Remote (source) TCP or UDP port.

Interface

Ingress interface.

Flow-type

Flow classification for hardware packet policing.

Min-TTL

Minimum time-to-live value expected from in the incoming packet. Any packet received with a lower TTL value will be dropped.

Slice

IFIB slice.

Flags

  • Has FGID: Delivered to multiple destinations.
  • No IFIB entry: IFIB entry suppressed.
  • Retrying FGID allocation.
  • In Pre-IFIB: Entry is in Pre-IFIB as well.
  • Deliver to one: If multiple bindings, will deliver to only one.

Location

rack/slot/module to deliver to.

Element References

  • location: rack/slot/module of client.
  • count: number of clients at that location.
  • scope: binding scope (LR:Logical Router, LOCAL:Local).

The following sample output is from the show lpts flows brief command:

RP/0/RSP0/CPU0:router# show lpts flows brief

+ - Additional delivery destination; L - Local interest; P - In Pre-IFIB

 L3   L4    VRF-ID   Local, Remote Address.Port      Interface    Location    LP
 ---- ----- -------- ------------------------------- ------------ ----------- --
 IPV4 ICMP  *        any.ECHO any                    any          (drop)      LP
 IPV4 ICMP  *        any.TSTAMP any                  any          (drop)      LP
 IPV4 ICMP  *        any.MASKREQ any                 any          (drop)      LP
 IPV6 ICMP6 *        any.ECHOREQ any                 any          (drop)      LP
 IPV4 any   default  224.0.0.2 any                   Gi0/1/0/1    0/5/CPU0     P

This table describes the significant fields shown in the display.



Table 6 show lpts flows brief Command Field Descriptions

Field

Description

L3

Layer 3 protocol (IPv4, IPv6, CLNL).

L4

Layer 4 protocol.

VRF-ID

VPN routing and forwarding (VRF) identification (vrfid) number.

Local, Remote Address.Port

Local (destination) and remote (source) IP addresses and TCP or UDP ports, or ICMP/IGMP packet types, or IPSec Security Parameters Indices.

Interface

Ingress interface.

Location

Delivery location:

  • rack/slot/moduleIndividual location.
  • [0xNNNNN]—Multiple locations (platform-dependent value).
  • (drop)—Do not deliver to any application.

LP

Local interest (to be processed by IPv4 or IPv6 stack directly) or entry is resident in Pre-IFIB.

Related Commands

Command

Description

show lpts bindings

Displays the binding information in the Port Arbitrator .

show lpts clients

Displays the client information for the Port Arbitrator .

show lpts ifib

To display the entries in the Internal Forwarding Information Base (IFIB), use the show lpts ifib command in EXEC mode.

show lpts ifib [entry] [ type { bgp4 | bgp6 | isis | mcast4 | mcast6 | ospf-mc4 | ospf-mc6 | ospf4 | ospf6 | raw4 | raw6 | tcp4 | tcp6 | udp4 | udp6 } | all ] [ brief [statistics] ] [slices] [times] [ location node-id ]

Syntax Description

entry

(Optional) Displays the IFIB entries.

type

(Optional) Displays the following protocol types.

  • bgp4 —IPv4 Border Gateway Protocol (BGP) slice
  • bgp6 —IPv6 BGP slice
  • isis —Intermediate System-to-Intermediate System (IS-IS) slice
  • mcast4 —IPv4 multicast slice
  • mcast6 —IPv6 multicast slice
  • ospf-mc4 —IPv4 Open Shortest Path First (OSPF) multicast slice
  • ospf-mc6 —IPv6 OSPF multicast slice
  • ospf4 —IPv4 OSPF slice
  • ospf6 —IPv6 OSPF slice
  • raw4 —IPv4 raw IP
  • raw6 —IPv6 raw IP
  • tcp4 —IPv4 Transmission Control Protocol (TCP) slice
  • tcp6 —IPv6 TCP slice
  • udp4 —IPv4 UDP slice
  • udp6 —IPv6 UDP slice

all

Displays all IFIB types.

brief

(Optional) Displays the IFIB entries in brief format.

statistics

(Optional) Displays the IFIB table with statistics information.

slices

(Optional) Displays IFIB slices.

times

(Optional) Displays the IFIB update transaction times.

location node-id

(Optional) Specifies the location of the Flow Manager. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use this command to display detailed information about the entries in an IFIB slice. This command is useful for debugging problems with delivering packets to applications.

When the statistics keyword is used, detailed statistics are displayed for packet count, number of entries in each slice, and a total entries count.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts ifib command:

RP/0/RSP0/CPU0:routershow lpts ifib

O - Opcode; A - Accept Counter; D - Drop Counter; F - Flow Type; L - Listener Tag; 
I - Local Flag; Y - SYN; T - Min TTL; DV - Deliver; DP - Drop; RE - Reassemble; na - Not Applicable
----------------------------------------------------
VRF-ID           : default (0x60000000)
Port/Type        : any
Source Port      : any
Dest IP          : any
Source IP        : any
Layer 4          : 88 (88)
Interface        : any (0x0)
O/A/D/F/L/I/Y/T  : DELIVER/0/0/EIGRP/IPv4_STACK/0/0/0
Deliver List     : 0/5/CPU0
----------------------------------------------------

This table describes the significant fields shown in the display.



Table 7 show lpts ifib entries Command Field Descriptions

Field

Description

VRF-ID

VPN routing and forwarding (VRF) identification (vrfid) number.

Port/Type

Destination (local) TCP or UDP port number, or ICMP/IGMP packet type, or IPSec Security Parameters Index.t2222.

Source Port

Source (remote) TCP or UDP port.

Dest IP

Destination (local) IP address.

Source IP

Source (remote) IP address.

Layer 4

Layer 4 protocol number (6 = TCP).

Note   

Only the common Layer 4 protocol names are displayed.

Interface

Ingress interface name.

O/S/P/R/L/I/Y

  • O: Opcode (DELIVER, DROP, or REASSEMBLE
  • S: Stats counter
  • P: Packet forwarding priority (LO, MED, or HIGH)
  • R: Rate limit (LO, MED, or HIGH)
  • L: Listener tag (IPv4_STACK, IPv6_STACK, or CLNL_STACK)
  • I: Local-interest flag (0 or 1)
  • Y: TCP SYN flag (0 or 1)

Deliver List

  • (drop)—Drop packet
  • rack/slot/module—Deliver to single destination
  • [0xNNNN]—Deliver to multiple destinations (platform-dependent format)

The following sample output is from the show lpts ifib brief command:

RP/0/RSP0/CPU0:router# show lpts ifib brief

 Slice    Local, Remote Address.Port            L4    Interface    Dlvr
 -------- ------------------------------------- ----- ------------ -----------
 TCP4     any.7 any                             TCP   any          0/RP1/CPU0
 TCP4     any.9 any                             TCP   any          0/RP1/CPU0

The following sample output is from the show lpts ifib brief statistics command:

RP/0/RSP0/CPU0:router# show lpts ifib brief statistics

 Slice    Local, Remote Address.Port            L4    Interface    Accept/Drop
 -------- ------------------------------------- ----- ------------ -----------
 TCP4     any.7 any                             TCP   any          0/0
 TCP4     any.9 any                             TCP   any          0/0
 TCP4     any.19 any                            TCP   any          0/0

 Slice    Num. Entries Accepts/Drops
 -------- ------------ -------------
TCP4     3            0/0
Total    3            0/0

Related Commands

Command

Description

show lpts ifib slices

Displays IFIB slice information.

show lpts ifib slices

To display Internal Forwarding Information Base (IFIB) slice information, use the show lpts ifib slices command in EXEC mode.

show lpts ifib slices [ type { bgp4 | bgp6 | isis | mcast4 | mcast6 | ospf-mc4 | ospf-mc6 | ospf4 | ospf6 | raw4 | raw6 | tcp4 | tcp6 | udp4 | udp6 } ] [all] [statistics] [times]

Syntax Description

type

(Optional) Enter protocol types.

  • bgp4 —IPv4 Border Gateway Protocol (BGP) slice
  • bgp6 —IPv6 BGP slice
  • isis —Intermediate System-to-Intermediate System (IS-IS) slice
  • mcast4 —IPv4 multicast slice
  • mcast6 —IPv6 multicast slice
  • ospf-mc4 —IPv4 Open Shortest Path First (OSPF) multicast slice
  • ospf-mc6 —IPv6 OSPF multicast slice
  • ospf4 —IPv4 OSPF slice
  • ospf6 —IPv6 OSPF slice
  • raw4 —IPv4 raw IP
  • raw6 —IPv6 raw IP
  • tcp4 —IPv4 Transmission Control Protocol (TCP) slice
  • tcp6 —IPv6 TCP slice
  • udp4 —IPv4 UDP slice
  • udp6 —IPv6 UDP slice

all

(Optional) Displays all entries.

statistics

(Optional) Displays the statistics for slice lookups.

times

(Optional) Displays the IFIB update transaction times.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show lpts ifib slices command when troubleshooting IFIB entries and slice assignments. This command is especially useful when troubleshooting problems with delivering packets to applications.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts ifib slices command:

RP/0/RSP0/CPU0:router# show lpts ifib slices 

Slice    L3   L4     Port  Location
-------- ---- ------ ----- --------
RAWIP4   IPV4 any    any   0/RP1/CPU0
RAWIP6   IPV6 any    any   0/RP1/CPU0
OSPF4    IPV4 OSPF   any   0/RP1/CPU0
OSPF6    IPV6 OSPF   any   0/RP1/CPU0
OSPF_MC4 IPV4 any    any   0/RP1/CPU0
OSPF_MC6 IPV6 any    any   0/RP1/CPU0
BGP4     IPV4 TCP    179   0/RP1/CPU0
BGP6     IPV6 TCP    179   0/RP1/CPU0

UDP4     IPV4 UDP    any   0/RP1/CPU0
UDP6     IPV6 UDP    any   0/RP1/CPU0
TCP4     IPV4 TCP    any   0/RP1/CPU0
TCP6     IPV6 TCP    any   0/RP1/CPU0
ISIS     CLNS -      any   0/RP1/CPU0
MCAST4   IPV4 any    any   0/RP1/CPU0
MCAST6   IPV6 any    any   0/RP1/CPU0

The following sample output is from the show lpts ifib slices times command:

RP/0/RSP0/CPU0:router# show lpts ifib slices times

Slice    L3   L4     Port  Location
-------- ---- ------ ----- --------
RAWIP4   IPV4 any    any   0/RP1/CPU0
RAWIP6   IPV6 any    any   0/RP1/CPU0
OSPF4    IPV4 OSPF   any   0/RP1/CPU0
OSPF6    IPV6 OSPF   any   0/RP1/CPU0
OSPF_MC4 IPV4 any    any   0/RP1/CPU0
OSPF_MC6 IPV6 any    any   0/RP1/CPU0
BGP4     IPV4 TCP    179   0/RP1/CPU0
BGP6     IPV6 TCP    179   0/RP1/CPU0

UDP4     IPV4 UDP    any   0/RP1/CPU0
UDP6     IPV6 UDP    any   0/RP1/CPU0
TCP4     IPV4 TCP    any   0/RP1/CPU0
TCP6     IPV6 TCP    any   0/RP1/CPU0
ISIS     CLNS -      any   0/RP1/CPU0
MCAST4   IPV4 any    any   0/RP1/CPU0
MCAST6   IPV6 any    any   0/RP1/CPU0
  Flow Manager 0/RP1/CPU0:
   total:5 tx 13 upd 1/-/1ms/tx

The following sample output is from the show lpts ifib slices statistics command:

RP/0/RSP0/CPU0:router# show lpts ifib slices all statistics

Slice    L3   L4     Port  Location   Lookups RmtDlvr Rejects RLDrops NoEntry
-------- ---- ------ ----- ---------- ------- ------- ------- ------- -------
RAWIP4   IPV4 any    any   0/0/CPU0   5       0       0       0       0
RAWIP6   IPV6 any    any   0/0/CPU0   0       0       0       0       0
OSPF4    IPV4 OSPF   any   0/0/CPU0   0       0       0       0       0
OSPF6    IPV6 OSPF   any   0/0/CPU0   0       0       0       0       0
OSPF_MC4 IPV4 any    any   0/0/CPU0   0       0       0       0       0
OSPF_MC6 IPV6 any    any   0/0/CPU0   0       0       0       0       0
BGP4     IPV4 TCP    179   0/0/CPU0   0       0       0       0       0
BGP6     IPV6 TCP    179   0/0/CPU0   0       0       0       0       0

UDP4     IPV4 UDP    any   0/0/CPU0   3704    0       979     0       0
UDP6     IPV6 UDP    any   0/0/CPU0   0       0       0       0       0
TCP4     IPV4 TCP    any   0/0/CPU0   0       0       0       0       0
TCP6     IPV6 TCP    any   0/0/CPU0   0       0       0       0       0
ISIS     CLNS -      any   0/0/CPU0   0       0       0       0       0
MCAST4   IPV4 any    any   0/0/CPU0   0       0       0       0       0
MCAST6   IPV6 any    any   0/0/CPU0   0       0       0       0       0
  Flow Manager 0/0/CPU0:
   Packets in: 3792
   Packets delivered locally without lookups: 83
   Slice lookups: 3709
     Rejects: 979

This table describes the significant fields shown in the display.



Table 8 show lpts ifib slices statistics Command Field Descriptions

Field

Description

Slice

Slice number.

L3-proto

Layer 3 protocol (IPv4, IPv6, CLNL).

L4-proto

Layer 4 protocol (TCP, UDP, and others).

Port

Local (destination) TCP or UDP port.

Location

Node location, in the format rack/slot/module.

Related Commands

Command

Description

show lpts ifib

Displays entries in the IFIB.

show lpts ifib statistics

To display Internal Forwarding Information Base (IFIB) statistics, use the show lpts ifib statistics command in EXEC mode.

show lpts ifib statistics [ location node-id ]

Syntax Description

location node-id

(Optional) Displays IFIB statistics for the designated node. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts ifib statistics command:

RP/0/RSP0/CPU0:router# show lpts ifib statistics

Flow Manager 0/RP1/CPU0:
   Packets in:254
   Packets delivered locally without lookups:0
   Slice lookups:254
     Post-lookup error drops:
      Failed ipv4_netio_input:1
     Rejects:254
    Packets delivered locally:0
    Packets delivered remotely:0

This table describes the significant fields shown in the display.



Table 9 show lpts ifib statistics Command Field Descriptions

Field

Description

Packets in

Packets presented to the LPTS decaps node in netio.

Packets delivered locally without lookups

Packets previously resolved on a LC delivered directly to L3.

Slice lookups

Packets requiring slice lookups.

Post-lookup error drops

Packets dropped after a slice lookup.

Rejects

Packets that caused a TCP RST or ICMP Port/Protocol Unreachable.

Packets delivered locally

Packets delivered to local applications after slice lookups.

Packets delivered remotely

Packets delivered to applications on remote RPs.


Note


The sample output is an example only and displays only those fields showing a value. No display exists for nonzero values. This command may show other values depending on your router configuration.


Related Commands

Command

Description

show lpts ifib

Displays the entries in an IFIB slice.

show lpts ifib times

To display Internal Forwarding Information Base (IFIB) update transaction times, use the show lpts ifib times command in EXEC mode.

show lpts ifib times [ location node-id ]

Syntax Description

location node-id

(Optional) Displays IFIB update transaction times for the designated node. The node-id argument is entered in the rack/slot/module notation.

Command Modes

EXEC

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts ifib times command:

RP/0/RSP0/CPU0:router# show lpts ifib times

Slice    L3   L4     Port  Location
-------- ---- ------ ----- --------
RAWIP4   IPV4 any    any   0/RP1/CPU0
RAWIP6   IPV6 any    any   0/RP1/CPU0
OSPF4    IPV4 OSPF   any   0/RP1/CPU0
OSPF6    IPV6 OSPF   any   0/RP1/CPU0
OSPF_MC4 IPV4 any    any   0/RP1/CPU0
OSPF_MC6 IPV6 any    any   0/RP1/CPU0
BGP4     IPV4 TCP    179   0/RP1/CPU0
BGP6     IPV6 TCP    179   0/RP1/CPU0
UDP4     IPV4 UDP    any   0/RP1/CPU0
UDP6     IPV6 UDP    any   0/RP1/CPU0
TCP4     IPV4 TCP    any   0/RP1/CPU0
TCP6     IPV6 TCP    any   0/RP1/CPU0
ISIS     CLNS -      any   0/RP1/CPU0
MCAST4   IPV4 any    any   0/RP1/CPU0
MCAST6   IPV6 any    any   0/RP1/CPU0
Flow Manager 0/RP1/CPU0:
 total:5 tx 13 upd 1/-/1ms/tx

This table describes the significant fields shown in the display.



Table 10 show lpts ifib times Command Field Descriptions

Field

Description

Slice

Slice number.

L3 Protocol

Layer 3 protocol (IPv4, IPV6, CLNL).

L4 Protocol

Layer 4 protocol (TCP, UDP, and so on).

Port

Local (destination) TCP or UDP port.

Location

Node location, in the format rack/slot/module.

Related Commands

Command

Description

show lpts ifib

Displays detailed information about entries in an IFIB slice.

show lpts mpa groups

To display aggregate information about multicast bindings for groups, use the show lpts mpa groups command in EXEC mode.

show lpts mpa groups type interface-path-id

Syntax Description

type

Interface type. For more information, use the question mark (?) online help function.

interface-path-id

Either a physical interface instance or a virtual interface instance as follows:

  • Physical interface instance. Naming notation is rack/slot/module/port and a slash between values is required as part of the notation.
    • rack: Chassis number of the rack.
    • slot: Physical slot number of the modular services card or line card.
    • module: Module number. A physical layer interface module (PLIM) is always 0.
    • port: Physical port number of the interface.
    Note   

    In references to a Management Ethernet interface located on a route processor card, the physical slot number is alphanumeric (RSP0 ) and the module is CPU0. Example: interface MgmtEth0/RSP0 /CPU0/0.

  • Virtual interface instance. Number range varies depending on interface type.

For more information about the syntax for the router, use the question mark (?) online help function.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show lpts mpa groups command is used to aggregate information about the multicast groups joined on a specified interface. This command also displays the filter mode and source list associated with the groups joined on a specified interface.

Task ID

Task ID

Operations

lpts

read

network

read

Examples

The following sample output is from the show lpts mpa groups command:

RP/0/RSP0/CPU0:router# show lpts mpa groups gigabitethernet 0/0/0/0 

  224.0.0.2 : includes 0, excludes 1, mode EXCLUDE
    <no source filter>
  224.0.0.13 : includes 0, excludes 1, mode EXCLUDE
    <no source filter>
  224.0.0.22 : includes 0, excludes 1, mode EXCLUDE
    <no source filter>

This table describes the significant fields shown in the display.



Table 11 show lpts mpa groups Command Field Descriptions

Field

Description

Includes

Displays the number of sockets that have set up an INCLUDE mode filter for that group and if there are any source-specific filters.

Excludes

Displays the number of sockets that have set up an EXCLUDE mode filter for that group and if there are any source-specific filters.

show lpts pifib

To display Pre-Internal Forwarding Information Base (Pre-IFIB) entries, use the show lpts pifib command in EXEC mode.

show lpts pifib [entry] [hardware { entry | police } [type {isis | ipv4 | ipv6} { frag | ixmp | mcast | tcp | udp | ipsec | raw | all } [ entry ] brief [statistics][location node-id]

Syntax Description

entry

(Optional) Pre-IFIB entry.

hardware

(Optional) Displays hardware for Pre-IFIB.

entry

(Optional) Displays the entries for Pre-IFIB.

police

(Optional) Displays the policer values that are being use.

type

(Optional) Protocol type.

isis

(Optional) Intermediate System-to-Intermediate System (IS-IS) sub Pre-IFIB type.

ipv4

(Optional) IPv4 sub Pre-IFIB type. Possible values include frag , ixmp , mcast , tcp , udp , ipsec , and raw .

ipv6

(Optional) IPv6 sub Pre-IFIB type. Possible values include frag , icmp , ixmp , mcast , tcp , udp , ipsec, and raw .

frag

(Optional) IPv4 or IPv6 fragment.

icmp

(Optional) IPv4 or IPv6 IXMP and Internet Group Management Protocol (IGMP).

ixmp

(Optional) IPv4 or IPv6 IXMP (ICMP and Internet Group Management Protocol [IGMP]).

mcast

(Optional) IPv4 or IPv6 Multicast.

tcp

(Optional) IPv4 or IPv6 Transmission Control Protocol (TCP).

udp

(Optional) IPv4 or IPv6 User Datagram Protocol (UDP).

ipsec

(Optional) Secure IP.

raw

(Optional) IPv4 orIPv6 raw IP.

all

(Optional) All sub Pre-IFIBs.

brief

(Optional) Pre-IFIB entries in brief format.

statistics

(Optional) Pre-IFIB table with statistics information.

location node-id

(Optional) The node-id argument is entered in the rack/slot/module notation (for example, 0/7/CPU0).

Command Default

By default, all entries are displayed.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show lpts pifib command with the brief keyword to perform the following functions:

  • Display entries of all or part of a Pre-IFIB.
  • Display a short description of each entry in the LPTS Pre-IFIB, optionally displaying packet counts for each entry.

    Note


    These statistics are used only for packets that are processed by a line card, route processor, or distributed route processor.


    Pre-IFIB statistics for packets processed by line card hardware are counted separately.

By default, all the defaults are displayed.

Task ID

Task ID

Operations

lpts

read

Examples

The following is sample output for the show lpts pifib command:

RP/0/RSP0/CPU0:routershow lpts pifib 

O - Opcode; F - Flow Type; L - Listener Tag; I - Local Flag; T - Min TTL;
na - Not Applicable
----------------------------------------------------
L3 Protocol       : CLNS
L4 Protocol       : -
VRF-ID            : default (0x60000000)
Destination IP    : any
Source IP         : any
Port/Type         : any
Source Port       : any
Is Fragment       : 0
Is SYN            : 0
Interface         : any (0x0)
O/F/L/I/T         : DELIVER/ISIS-default/CLNS_STACK/0/0
Deliver List      : FGID 11935
Accepts/Drops     : 0/0
Is Stale          : 0

The following is sample output for the show lpts pifib type command using the ipv4 and tcp keywords.

RP/0/RSP0/CPU0:routershow lpts pifib type ipv4 tcp

O - Opcode; F - Flow Type; L - Listener Tag; I - Local Flag; T - Min TTL;
na - Not Applicable
----------------------------------------------------
L3 Protocol       : IPV4
L4 Protocol       : TCP
VRF-ID            : default (0x60000000)
Destination IP    : any
Source IP         : any
Port/Type         : Port:23
Source Port       : any
Is Fragment       : 0
Is SYN            : 0
Interface         : any (0x0)
O/F/L/I/T         : DELIVER/TELNET-default/IPv4_LISTENER/0/0
Deliver List      : 0/RSP0

/CPU0
Accepts/Drops     : 0/0
Is Stale          : 0
----------------------------------------------------

The following is sample output from the show lpts pifib command with the entry and brief keywords added :

RP/0/RSP0/CPU0:router# show lpts pifib entry brief

* - Critical Flow; I - Local Interest;
X - Drop; R - Reassemble;

 Type       VRF-ID   Local, Remote Address.Port L4    Interface    Deliver
 ---------- -------- -------------------------- ----- ------------ -------------

 ISIS       *        - -                        -     any          0/0/CPU0
 IPv4_frag  *        any any                    any   any          R
 IPv4_IXMP  *        any.ECHO any               ICMP  any          XI
 IPv4_IXMP  *        any.TSTAMP any             ICMP  any          XI
 IPv4_IXMP  *        any.MASKREQ any            ICMP  any          XI
 IPv4_IXMP  *        any any                    ICMP  any          0/0/CPU0
 IPv4_IXMP  *        any any                    IGMP  any          0/0/CPU0
 IPv4_mcast *        224.0.0.5 any              any   any          0/0/CPU0
 IPv4_mcast *        224.0.0.6 any              any   any          0/0/CPU0
 IPv4_mcast *        224.0.0.0/4 any            any   any          0/0/CPU0

 IPv4_TCP   *        any.179 any                TCP   any          0/0/CPU0
 IPv4_TCP   *        any any.179                TCP   any          0/0/CPU0
 IPv4_TCP   *        any any                    TCP   any          0/0/CPU0
 IPv4_UDP   *        any any                    UDP   any          0/0/CPU0
 IPv4_IPsec *        any any                    ESP   any          0/0/CPU0
 IPv4_IPsec *        any any                    AH    any          0/0/CPU0
 IPv4_rawIP *        any any                    OSPF  any          0/0/CPU0
 IPv4_rawIP *        any any                    any   any          0/0/CPU0
 IPv6_frag  *        any any                    any   any          R
 IPv6_ICMP  *        any.na any                 ICMP6 any          XI
 IPv6_ICMP  *        any any                    ICMP6 any          0/0/CPU0
 IPv6_mcast *        ff02::5 any                any   any          0/0/CPU0
 IPv6_mcast *        ff02::6 any                any   any          0/0/CPU0
 IPv6_mcast *        ff00::/8 any               any   any          0/0/CPU0
 IPv6_TCP   *        any.179 any                TCP   any          0/0/CPU0
 IPv6_TCP   *        any any.179                TCP   any          0/0/CPU0
 IPv6_TCP   *        any any                    TCP   any          0/0/CPU0
 IPv6_UDP   *        any any                    UDP   any          0/0/CPU0
 IPv6_IPsec *        any any                    ESP   any          0/0/CPU0
 IPv6_IPsec *        any any                    AH    any          0/0/CPU0
 IPv6_rawIP *        any any                    OSPF  any          0/0/CPU0
 IPv6_rawIP *        any any                    any   any          0/0/CPU0

The following sample output is from the show lpts pifib command with the entry, brief, and entry brief statistics keywords added :

RP/0/RSP0/CPU0:router# show lpts pifib entry brief statistics

* - Critical Flow; I - Local Interest;
X - Drop; R - Reassemble;

 Type       VRF-ID   Local, Remote Address.Port L4    Interface    Accepts/Drops

 ---------- -------- -------------------------- ----- ------------ -------------

 ISIS       *        - -                        -     any          0/0
 IPv4_frag  *        any any                    any   any          0/0
 IPv4_IXMP  *        any.ECHO any               ICMP  any          0/0
 IPv4_IXMP  *        any.TSTAMP any             ICMP  any          0/0
 IPv4_IXMP  *        any.MASKREQ any            ICMP  any          0/0
 IPv4_IXMP  *        any any                    ICMP  any          5/0
 IPv4_IXMP  *        any any                    IGMP  any          0/0
 IPv4_mcast *        224.0.0.5 any              any   any          0/0
 IPv4_mcast *        224.0.0.6 any              any   any          0/0
 IPv4_mcast *        224.0.0.0/4 any            any   any          0/0
 IPv4_TCP   *        any.179 any                TCP   any          0/0
 IPv4_TCP   *        any any.179                TCP   any          0/0
 IPv4_TCP   *        any any                    TCP   any          0/0
 IPv4_UDP   *        any any                    UDP   any          4152/0
 IPv4_IPsec *        any any                    ESP   any          0/0
 IPv4_IPsec *        any any                    AH    any          0/0
 IPv4_rawIP *        any any                    OSPF  any          0/0

------------------------

statistics:

Type            Num. Entries         Accepts/Drops

------          ------------         -------------
ISIS            1                    0/0
IPv4_frag       1                    0/0
IPv4_IXMP       5                    5/0
IPv4_mcast      3                    0/0
IPv4_TCP        3                    0/0
IPv4_UDP        1                    4175/0
IPv4_IPsec      2                    0/0
IPv4_rawIP      2                    0/0
IPv6_frag       1                    0/0
IPv6_ICMP       2                    0/0
IPv6_mcast      3                    0/0
IPv6_TCP        3                    0/0
IPv6_UDP        1                    0/0
IPv6_IPsec      2                    0/0
IPv6_rawIP      2                    0/0
Total           32

Packets into Pre-IFIB: 4263
Lookups: 4263
Packets delivered locally: 4263
Packets delivered remotely: 0

This table describes the significant fields shown in the display for the show lpts pifib command with the brief and statistics keywords .



Table 12 show lpts pifib Command Field Descriptions

Field

Description

Type

Hardware entry type.

VRF ID

VPN routing and forwarding (VRF) identification (vrfid) number.

Local, Remote Address. Port

Indicates local address (in the form of local port and type) and remote address (remote port).

L4

Layer 4 protocol of the entry.

Interface

Interface for this entry.

Accepts/Drops

Number of packets sent to DestAddr/Number of packets dropped due to policing.

Num. Entries

Number of pre-ifib entries of the listed type.

Packets into Pre-IFIB

Packets presented for pre-IFIB lookups.

Lookups

Packets looked up.

Packets delivered locally

Packets delivered to local applications or the local stack (n duplicated) packets duplicated for delivery to applications and the local stack.

Packets delivered remotely

Packets delivered to applications or for lookup on other RPs.

show lpts pifib hardware context

To display the context for the Local Packet Transport Services (LPTS) pre-IFIB hardware-related data structures, use the show lpts pifib hardware context command in EXEC mode.

show lpts pifib hardware context [ location { all | } ]

Syntax Description

location node-id

(Optional) Displays pre-Internal Forwarding Information Base (IFIB) information for the designated node. The node-id argument is entered in the rack/slot/module notation.

all

Specifies all locations.

Command Default

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts pifib hardware context command with the location keyword:

RP/0/RSP0/CPU0:router# show lpts pifib hardware context location 0/1/0

Node: 0/1/CPU0:
----------------------------------------
ACL ID for block 0: 3
Batching mode: No batching
TCAM Mgr ready: Yes
Mstats Mgr ready: Yes
Metro Driver ready: Yes
Resource sync: Yes
Sweep invoked: Yes
Initialization phase: Done
Queue for TCAM Batching:
    Size: 0 Head ptr: 0x0
Queue for Entry Processing:
    Size: 0 Head ptr: 0x0
Queue for Resources Releasing:
    Size: 0 Head ptr: 0x0
--------
IPv4 Region:
Block [0]: 
    # of TCAM entries: 56 block created: Yes
    first entry in the block: 0x482a055c
Last non mandatory entry: 0x482c1a08
Queue for Mandatory entries not in TCAM:
    Size: 0 Head ptr: 0x0
Queue for Non Mandatory entries not in TCAM:
    Size: 0 Head ptr: 0x0
1st entry to be programmed: 0x0
Max. of entries: 15999
# of entries in shadow list: 54
1st entry in shadow list: 0x482a055c
last entry in shadow list: 0x48303534
--------
IPv6 Region:
Block [0]: 
    # of TCAM entries: 20 block created: Yes
    first entry in the block: 0x482c1720
Last non mandatory entry: 0x482c1b00
Queue for Mandatory entries not in TCAM:
    Size: 0 Head ptr: 0x0
Queue for Non Mandatory entries not in TCAM:
    Size: 0 Head ptr: 0x0
1st entry to be programmed: 0x0
Max. of entries: 15999
# of entries in shadow list: 20
1st entry in shadow list: 0x482c1720
last entry in shadow list: 0x482e2344
--------
ISIS Region:
Block [0]: 
    # of TCAM entries: 1 block created: Yes
    first entry in the block: 0x482e2cf4
Last non mandatory entry: 0xfd30d088
Queue for Mandatory entries not in TCAM:
    Size: 0 Head ptr: 0x0
Queue for Non Mandatory entries not in TCAM:
    Size: 0 Head ptr: 0x0
1st entry to be programmed: 0x0
Max. of entries: 15999
# of entries in shadow list: 1
1st entry in shadow list: 0x482e2cf4
last entry in shadow list: 0x482e2cf4
# of TCAM Insert: 0
# of TCAM Delete: 0
# of TCAM Update: 0
# of resource leaks: 0

show lpts pifib hardware entry

To display entries in the Local Packet Transport Services (LPTS) pre-IFIB hardware table, use the show lpts pifib hardware entry command in EXEC mode.

show lpts pifib hardware entry [ type { ipv4 | ipv6 | isis } ] [ start-index number num-entries number ] [ brief | statistics ] [ location { all | node_id } ]

Syntax Description

type

(Optional) Specifies the hardware entry type. Enter one of the following types:

  • ipv4 —Specifies IPv4 entries.
  • ipv6 —Specifies IPv6 entries.
  • isis —Specifies ISIS entries.

start-index number

(Optional) Starting index number.

num-entries number

(Optional) Maximum entries permitted.

brief

(Optional) Displays summary hardware entry information.

statistics

(Optional) Displays hardware entry accept or drop statistics for each summary entry.

location all

(Optional) Specifies all locations.

location node-id

(Optional) Displays pre-Internal Forwarding Information Base (IFIB) information for the designated node. The node-id argument is entered in the rack/slot/module notation.

Command Default

Displays hardware entry information in brief.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts pifib hardware entry command with the location keyword:

RP/0/RSP0/CPU0:router# show lpts pifib hardware entry location 0/1/CPU0

Node: 0/0/CPU0:
----------------------------------------
M - Fabric Multicast;
L - Listener Tag; T - Min TTL;
F - Flow Type;
DestNode - Destination Node;
DestAddr - Destination Fabric queue;
SID - Stream ID;
Po - Policer; Ct - Stats Counter;
Lp - Lookup priority; Sp - Storage Priority;
Ar - Average rate limit; Bu - Burst;
HAr - Hardware Average rate limit; HBu - Hardware Burst;
Cir - Committed Information rate in HAL
Rsp - Relative sorting position;
Rtp - Relative TCAM position;
na - Not Applicable or Not Available
----------------------------------------------------
VRF ID            : any
Destination IP    : any
Source IP         : any
Is Fragment       : 0
Interface         : any
M/L/T/F           : 0/ISIS_FM/0/ISIS-default
DestNode          : 48
DestAddr          : 48
SID               : 9
L4 Protocol       : -
Source port       : any
Destination Port  : any
Ct                : 0xd84da
Accepted/Dropped  : 0/0
Lp/Sp             : 0/0
# of TCAM entries : 1
HPo/HAr/HBu/Cir   : 1879638/2000pps/2000ms/2000pps
State             : Entry in TCAM
Rsp/Rtp           : 0/2

             Node: 0/1/CPU0:
----------------------------------------
V - Vital; M - Fabric Multicast;
C - Moose Congestion Flag; L - Listener Tag; T - Min TTL;
F - Flow Type;
DestNode - Destination Node;
DestAddr - Destination Fabric Address;
Sq - Ingress Shaping Queue; Dq - Destination Queue;
Po - Policer; Ct - Stats Counter;
Lp - Lookup priority; Sp - Storage Priority;
Ar - Average rate limit; Bu - Burst;
Rsp - Relative sorting position;
----------------------------------------------------
L4 Protocol       : any
VRF ID            : any
Source IP         : any
Port/Type         : any
Source Port       : any
Is Fragment       : 1
Is SYN            : any
Interface         : any
V/M/C/L/T/F       : 0/0/0/IPv4_REASS/0/Fragment
DestNode          : Local
DestAddr          : Punt
Sq/Dq/Ct          : 4/na/0x24400
Accepted/Dropped  : 0/0
Lp/Sp             : 0/0
# of TCAM entries : 1
Po/Ar/Bu          : 101/1000pps/100ms
State             : Entry in TCAM
Rsp/Rtp           : 0/0
----------------------------------------------------

This table describes the significant fields shown in the display.



Table 13 show lpts pifib hardware entry Command Field Descriptions

Field

Description

L4 Protocol

Layer 4 protocol of the entry.

VRF ID

VPN routing and forwarding (VRF) identification (vrfid) number.

Source IP

Source IP address for this entry.

Port/Type

Port or Internet Control Message Protocol (ICMP) type for this entry.

Source Port

Source port for this entry.

Is Fragment

Indicates if this entry applies to IP fragments.

Is SYN

Indicates if this entry applies to TCP SYNs.

Interface

Interface for this entry.

V/M/C/L/T/F

  • V—vital
  • M—fabric multicast
  • C—moose congestion flag
  • L—listener tag
  • T—minimum time-to-live
  • F—flow type

DestNode

Destination node to which to send the packet.

DestAddr

Destination address to which to send the packet.

Sq/Dq/Ct

  • Sq—Ingress Shaping Queue
  • Dq—Destination Queue
  • Ct—Stats Counter

Accepted/Dropped

Number of packets sent to DestAddr/Number of packets dropped due to policing.

show lpts pifib hardware police

To display the policer configuration value set, use the show lpts pifib hardware police command in EXEC mode.

show lpts pifib hardware police [ location { all | node-id } ]

Syntax Description

location node-id

(Optional) Displays pre-Internal Forwarding Information Base (IFIB) information for the designated node. The node-id argument is entered in the rack/slot/module notation.

all

Specifies all locations.

Command Default

If no policer is configured, the default value is the configured rate.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

This sample output is from the show lpts pifib hardware police command with the location keyword for 0/2/CPU0:

RP/0/RSP0/CPU0:router#show lpts pifib hardware police location 0/2/CPU0 


-------------------------------------------------------------
                Node 0/2/CPU0:
-------------------------------------------------------------
 Burst = 100ms for all flow types 
-------------------------------------------------------------
FlowType               Policer Type    Cur. Rate Def. Rate Accepted   Dropped  
---------------------- ------- ------- --------- --------- ---------- ---------
unconfigured-default   100     Static  500       500       0          0        
Fragment               106     Static  1000      1000      0          0        
OSPF-mc-known          107     Static  20000     20000     0          0        
OSPF-mc-default        111     Static  5000      5000      0          0        
OSPF-uc-known          161     Static  5000      5000      0          0        
OSPF-uc-default        162     Static  1000      1000      0          0        
ISIS-known             108     Static  20000     20000     0          0        
ISIS-default           112     Static  5000      5000      0          0        
BFD-known              170     Static  8500      8500      0          0        
BFD-default            171     Static  8500      8500      0          0        
BFD-MP-known           177     Static  8400      8400      0          0        
BFD-MP-0               178     Static  128       128       0          0        
BGP-known              113     Static  25000     25000     0          0        
BGP-cfg-peer           114     Static  10000     10000     0          0        
BGP-default            115     Static  1500      1500      0          0        
PIM-mcast-default      116     Static  23000     23000     0          0        
PIM-mcast-known        176     Static  23000     23000     0          0        
PIM-ucast              117     Static  10000     10000     0          0        
IGMP                   118     Static  3500      3500      0          0        
ICMP-local             119     Static  2500      2500      0          0        
ICMP-app               120     Static  2500      2500      0          0        
ICMP-control           164     Static  2500      2500      0          0        
ICMP-default           121     Static  2500      2500      0          0        
LDP-TCP-known          122     Static  25000     25000     0          0        
LDP-TCP-cfg-peer       152     Static  10000     10000     0          0        
LDP-TCP-default        154     Static  10000     10000     0          0        
LDP-UDP                158     Static  2500      2500      0          0        
All-routers            160     Static  10000     10000     0          0        
LMP-TCP-known          123     Static  25000     25000     0          0        
LMP-TCP-cfg-peer       153     Static  10000     10000     0          0        
LMP-TCP-default        155     Static  10000     10000     0          0        
LMP-UDP                159     Static  2500      2500      0          0        
RSVP-UDP               124     Static  7000      7000      0          0        
RSVP-default           125     Static  500       500       0          0        
RSVP-known             126     Static  7000      7000      0          0        
IKE                    127     Static  1000      1000      0          0        
IPSEC-known            129     Static  3000      3000      0          0        
IPSEC-default          128     Static  1000      1000      0          0        
MSDP-known             130     Static  1000      1000      0          0        
MSDP-cfg-peer          131     Static  1000      1000      0          0        
MSDP-default           132     Static  1000      1000      0          0        
SNMP                   133     Static  2000      2000      0          0        
SSH-known              135     Static  1000      1000      0          0        
SSH-default            136     Static  1000      1000      0          0        
HTTP-known             137     Static  1000      1000      0          0        
HTTP-default           138     Static  1000      1000      0          0        
SHTTP-known            139     Static  1000      1000      0          0        
IFIB_FT_SHTTP_DEFAULT  140     Static  1000      1000      0          0        
TELNET-known           141     Static  1000      1000      0          0        
TELNET-default         142     Static  1000      1000      0          0        
CSS-known              143     Static  1000      1000      0          0        
CSS-default            144     Static  1000      1000      0          0        
RSH-known              145     Static  1000      1000      0          0        
RSH-default            146     Static  1000      1000      0          0        
UDP-known              147     Static  25000     25000     0          0        
UDP-listen             156     Static  4000      4000      0          0        
UDP-cfg-peer           157     Static  4000      4000      0          0        
UDP-default            101     Static  500       500       0          0        
TCP-known              148     Static  25000     25000     0          0        
TCP-listen             149     Static  25000     25000     0          0        
TCP-cfg-peer           150     Static  25000     25000     0          0        
TCP-default            102     Static  500       500       0          0        
Mcast-known            151     Static  25000     25000     0          0        
Mcast-default          103     Static  500       500       0          0        
Raw-listen             104     Static  500       500       0          0        
Raw-default            105     Static  500       500       0          0        
Ip-Sla                 163     Static  10000     10000     0          0        
EIGRP                  109     Static  20000     20000     0          0        
RIP                    110     Static  20000     20000     0          0        
L2TPv3                 165     Static  25000     25000     0          0        
PCEP                   166     Static  100       100       0          0        
GRE                    167     Static  1000      1000      0          0        
VRRP                   168     Static  1000      1000      0          0        
HSRP                   169     Static  400       400       0          0        
MPLS-oam               172     Static  100       100       0          0        
L2TPv2                 179     Static  25000     25000     0          0        
DNS                    173     Static  500       500       0          0        
RADIUS                 174     Static  7000      7000      0          0        
TACACS                 175     Static  500       500       0          0        
NTP-default            134     Static  500       500       0          0        
NTP-known              180     Static  500       500       0          0        

------------------------
statistics:
Packets accepted by deleted entries: 0
Packets dropped by deleted entries: 0
Run out of statistics counter errors: 0

This table describes the significant fields shown in the display.



Table 14 show lpts pifib hardware police Command Field Descriptions

FIeld

Description

FlowType

Type of flow that is binding between a tuple and a destination.

Rate (PPS)

Policer rate in packets per second (PPS).

Accept

Number of packets that are accepted by this policer.

Drop

Number of packets that are dropped by this policer.

Related Commands

Command

Description

flow (LPTS)

Configures the policer for the LPTS flow type.

lpts pifib hardware police

Configures the ingress policers and enters pifib policer global configuration mode.

show lpts pifib hardware usage

To display hardware table usage, use the show lpts pifib hardware usage command in EXEC mode.

show lpts pifib hardware usage [ type { ipv4 | ipv6 | isis } ] [ location { node-id | all } ]

Syntax Description

type

(Optional) Specifies the hardware entry type. Enter one of the following types:

  • ipv4 —Specifies IPv4 entries.
  • ipv6 —Specifies IPv6 entries.
  • isis —Specifies ISIS entries.

location node-id

(Optional) Displays pre-Internal Forwarding Information Base (IFIB) information for the designated node. The node-id argument is entered in the rack/slot/module notation.

a ll

(Optional) Specifies all locations.

Command Default

Without the optional parameters, the show lpts pifib hardware usage command displays a brief summary of hardware entry information.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts pifib hardware usage command with the location keyword:

RP/0/RSP0/CPU0:router# show lpts pifib hardware usage location 0/1/cpu0

Type       Size            Used            Used(%)
---------- --------------- --------------- -------
ipv4       6000            21              0.35
ipv6       4000            15              0.38
isis       4000            1               0.03

This table describes the significant fields shown in the display.



Table 15 show lpts pifib hardware usage Command Field Descriptions

Field

Description

Type

Type of pre-IFIB entry.

Size

Maximum number of entries (72-bits) allowed for the type.

Used

Number of entries in use.

Used(%)

Percentage of total entries in use.

show lpts pifib statistics

To display Pre-Internal Forwarding Information Base (Pre-IFIB) statistics, use the show lpts ifib statistics command in EXEC mode.

show lpts pifib statistics [ location node-id ]

Syntax Description

location node-id

(Optional) Displays Pre-IFIB statistics for the designated node. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced .

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts pifib statistics command:

RP/0/RSP0/CPU0:routershow lpts pifib statistics

Packets into Pre-IFIB:80
Lookups:80
Packets delivered locally:80
Packets delivered remotely:0

This table describes the significant fields shown in the display.



Table 16 show lpts pifib statistics Command Field Descriptions

Field

Description

Packets into Pre-IFIB

Packets presented for pre-IFIB lookups.

Lookups

Packets looked up.

Packets delivered locally

Packets delivered to local applications or the local stack (n duplicated) packets duplicated for delivery to applications and the local stack.

Packets delivered remotely

Packets delivered to applications or for lookup on other RPs.

Related Commands

Command

Description

show lpts pifib

Displays information about pre-IFIB entries.

show lpts port-arbitrator statistics

To display local packet transport services (LPTS) port arbitrator statistics, use the show lpts port-arbitrator statistics command in EXEC mode.

show lpts port-arbitrator statistics

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts port-arbitrator statistics command:

RP/0/RSP0/CPU0:routershow lpts port-arbitrator statistics

LPTS Port Arbitrator statistics:
 PA FGID-DB library statistics:
  0 FGIDs in use, 512 cached, 0 pending retries
  0 free allocation slots, 0 internal errors, 0 retry attempts
  1 FGID-DB notify callback, 0 FGID-DB errors returned
  FGID-DB permit mask: 0x7 (alloc mark rack0)
  PA API calls:
            1 init              1 realloc_done
            8 alloc             8 free
           16 join             16 leave
            8 detach
  FGID-DB API calls:
            1 register          1 clear_old
            1 alloc             0 free
           16 join             16 leave
            0 mark              1 mark_done

show lpts vrf

To display the Local Packet Transport Services (LPTS) VPN routing and forwarding (VRF) instance identification numbers and names, use the show lpts vrf command in EXEC mode.

show lpts vrf

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

lpts

read

Examples

The following sample output is from the show lpts vrf command:

RP/0/RSP0/CPU0:routershow lpts vrf

VRF-ID      VRF-NAME
0x00000000  *
0x60000000  default

This table describes the significant fields shown in the display.



Table 17 show lpts vrf Command Field Descriptions

Field

Description

VRF-ID

VPN routing and forwarding (VRF) identification (vrfid) number.

VRF-NAME

Name given to the VRF.