Cisco ASR 9000 Series Aggregation Services Router System Management Command Reference, Release 4.1
Hardware Redundancy and Node Administration Commands on the Cisco ASR 9000 Series Router
Downloads: This chapterpdf (PDF - 1.76MB) The complete bookPDF (PDF - 7.22MB) | Feedback

Hardware Redundancy and Node Administration Commands on the Cisco ASR 9000 Series Router

Contents

Hardware Redundancy and Node Administration Commands on the Cisco ASR 9000 Series Router

This module describes the commands used to manage the hardware redundancy, power, and administrative status of the nodes on a router running Cisco IOS XR software.

clear canbus

To clear the counters used for statistics regarding the CAN bus, use the clear canbus command in administration EXEC mode.

clear canbus { client-stats | controller-stats | server-stats } location { all | node-id }

Syntax Description

client-stats

Clears CAN bus client statistics.

controller-stats

Clears CAN bus controller statistics.

server-stats

Clears CAN bus server statistics.

location {all | node-id}

Clears the CAN bus statistics for a specific node or all nodes.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

Task ID

Task ID Operation

sysmgr

read

Examples

The following example illustrates how to use the clear canbus command:

RP/0/RSP0/CPU0:router(admin)# clear canbus server-stats location all

Related Commands
Related Information

Command

Description

show canbus

Displays the statistics regarding the CAN bus.

clear plugin slot counts

To clear the running counts of the backplane connector slot plugins, use the clear plugin slot counts command in administration EXEC mode.

clear plugin slot counts location node-id

Syntax Description

location node-id Clears plugin slot counts on the designated node. The node-id argument is expressed in the rack/slot/module notation.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.9.1

This command was introduced.

Usage Guidelines

The clear plugin slot counts command can be used only if the revised backplane ID card (BPID-02) is installed. If the BPID-02 card is not installed, the following error message is displayed:

0/1/CPU0 slot counts 'current' ...Response error: 'ENVMON' detected the 'warning' condition 'Hardware not available'

Task ID

Task ID Operation

sysmgr

execute

Examples

The following example illustrates how to use the clear plugin slot counts command:

RP/0/RSP0/CPU0:router(admin)# clear plugin slot counts location 0/FT1/SP

Fri Jan 15 10:15:55.388 pst

 0/FT1/SP slot counts 'current' ... cleared
RP/0/RSP0/CPU0:router(admin)# show plugin slot counts location 0/FT1/SP

Fri Jan 15 10:16:15.503 pst

Backplane connector slot plugin counters

                        Current         Cumulative
0/FT1/SP                0               14

Related Commands
Related Information

Command

Description

show plugin slot counts

Displays cumulative and running counts of card insertions per slot.

show canbus

Displays the statistics regarding the CAN bus.

fpd auto-upgrade

To enable the automatic upgrade of FPD images during a software upgrade, use the fpd auto-upgrade command in

administration configuration

mode. To disable automatic FPD upgrades, use the no form of this command.

fpd auto-upgrade

Syntax Description

This command has no keywords or arguments.

Command Default

FPD images are not automatically upgraded.

Command Modes

Administration configuration

Command History

Release Modification
Release 4.0.1

This command was introduced.

Usage Guidelines

By default automatic upgrades of the FPD images are not performed during a software upgrade. Once the fpd auto-upgrade command is enabled, when you upgrade the software and an FPD upgrade is required, the FPD upgrade is done automatically before the router is rebooted. The automatic FPD upgrade works only if the FPD image is upgraded together with the mini installation PIE. For example, use the install add and install activate commands as shown here:

(admin)# install add comp-hfr-mini.pie hfr-fpd.pie hfr-mpls-p.pie
(admin)# install activate disk0:/comp-hfr-mini.pie disk0:/hfr-fpd.piedisk0: hfr-mpls-p.pie
  

Task ID

Task ID Operation
system

read, write

Examples

The following example shows how to enable automatic FPD upgrades:

RP/0/RSP0/CPU0:router(admin-config)# fpd auto-upgrade 

Related Commands
Related Information

Command

Description

upgrade hw-module fpd

Manually upgrades the current field-programmable device (FPD) image package on a module.

install add

Adds the contents of a PIE file to a storage device .

hw-module location reload

To reset the power-cycle or reload the hardware for a specific node, or for all nodes installed in the router, use the hw-module location reload command in EXEC or administration EXEC mode.

hw-module location node-id reload { path | warm }

Syntax Description

node-id

Node whose hardware attributes you want to configure. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

path

TFTP or disk path to the image you want to download onto the specific node or nodes.

warm

Specifies a warm reload of the node.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To reset a specific node, use the hw-module location reload command in EXEC mode.

To reset a specific node or all nodes, use the hw-module location reload command in administration EXEC mode.


Note


Before reloading nodes, we recommend using the cfs check command to check the sanity of the configuration file system and attempt to recover from internal inconsistencies.


Task ID

Task ID

Operations

root-lr

execute (in EXEC mode)

sysmgr

execute (in EXEC mode and administration EXEC mode)

Examples

This example shows how to reset the hardware on a specific node from EXEC mode:

RP/0/RSP0/CPU0:router # hw-module location 0/1/CPU0 reload
                        

This example shows how to reset the hardware on a specific node from administration EXEC mode:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# hw-module location 0/3/CPU0 reload
       

This example shows how to reset the hardware on a specific fabric card node:

RP/0/RSP0/CPU0: router (admin) # hw module location 0/fc0/SP reload

Related Commands
Related Information

Command

Description

cfs check

Performs a check of the Configuration File System (CFS).

hw-module power location

To power on a specified line card, use the hw-module power location command in administration configuration mode. To power off a line card, use the no form of this command.

hw-module power location node-id

no hw-module power location node-id

Syntax Description

location node-id

Identifies the node to power on. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Power is on for all nodes.

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.0.0

The override option was removed.

Usage Guidelines

The hw-module power location command is available for line cards only; it is not available for route switch processor (RSP) cards.

Use the show platform command to view a summary of the nodes in the router, including status information.

By default, cards that do not have a power consumption value programmed on the manufacturing EEPROM cannot be powered up or booted. To correct an issue with such cards, that possibly is because of an incorrectly programmed EEPROM, you can use the hw-module power command with the override option.

Task ID

Task ID

Operations

root-system

read, write

root-lr

read, write

Examples

The following example shows how to power on a line card:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module power location 0/1/0
         

The following example shows how to disable the power-on feature for a line card:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module power disable location 0/SM3/SP
         

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.

hw-module power disable

To disable the node power-on feature on a specific line card, use the hw-module power disable command in administration configuration mode. To reenable the node power-on feature on a line card, use the no form of this command.

hw-module power disable location node-id

no hw-module power disable location node-id

Syntax Description

location node-id

Identifies the node whose power-on feature you want to disable. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Power is on for all nodes.

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 4.0.0

The override keyword was removed.

Usage Guidelines

Use the show platform command to view a summary of the nodes in the router, including status information.

The hw-module power disable command is available for line cards only; it is not available for RP cards.

Task ID

Task ID

Operations

sysmgr

read, write

root-lr

read, write

Examples

The following example shows how to disable the node power-on feature on a line card:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module power disable location 0/0/CPU0
         

The following example shows how to disable the node power-on feature on a fabric card:

RP/0/RSP0/CPU0:router (admin-config) # hw-module power disable location 0/fc0/SP

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.

hw-module profile feature

To enable a feature bundle on the router, use the hw-module profile feature command in administration configuration mode. To disable a feature bundle, use the no form of this command.

hw-module profile feature { default | l2 }

no hw-module profile feature { default | l2 }

Syntax Description

default

Feature profile that supports all features except provider backbone bridge (PBB).

l2

Feature profile that supports PBB, but does not support IPv6, reverse-path forwarding (RPF) and netflow.

Command Default

The default feature profile is default.

Command Modes

Administration configuration

Command History

Release Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

If you do not configure the feature profile, the default profile is active. The default feature profile does not support provider backbone bridge (PBB). If you need support for PBB, configure the L2 feature profile.

If you do not reload the line cards after configuring the feature profile, the configured profile is not active and this warning message is displayed. You must reload the affected line card so that the configured profile matches the active profile.

LC/0/1/CPU0:Nov 5 02:50:42.732 : prm_server[236]: Configured
'hw-module profile feature l2' does not match active 'hw-module
profile feature default'. You must reload this line card in order
to activate the configured profile on this card or you must change
the configured profile.
  

If you have configured features that are not supported in your active feature profile, this warning is displayed. You should either change the feature profile configuration, or remove the non-supported features.

LC/0/1/CPU0:Nov 5 02:50:42.732 : prm_server[236]: Active 'hw-module
profile feature l2' does not support IPv6, RPF, or Netflow
features. Please remove all unsupported feature configurations.
        

Task ID

Task ID Operation

system

read, write

root-lr

read, write

Examples

This example shows how to set the feature profile to L2:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module profile 
feature l2

Wed Dec  8 08:29:54.053 PST
L2 feature profile does NOT support the following features: 
IPv6, RPF, Netflow.
In order to activate this new memory resource profile,
you must manually reboot the line cards.
RP/0/RSP0/CPU0:router(admin-config)# commit
  

Related Commands
Related Information

Command

Description

show hw-module profile

Displays the active profiles.

hw-module profile scale

To specify a scale profile for the router, use the hw-module profile scale command in administration configuration mode.

hw-module profile scale { default | l3 | l3xl }

Syntax Description

default

Scale profile applicable for deployments that require large Layer 2 MAC tables (up to 512,000 entries) and a relatively small number of Layer 3 routes (less than 512,000).

l3

Scale profile applicable for deployments that require more Layer 3 routes (up to 1 million) and smaller Layer 2 MAC tables (less than 128,000 entries).

l3xl

Scale profile applicable for deployments that require a very large number of Layer 3 routes (up to 1.3 million) and minimal Layer 2 functionality.

Command Default

default is the default scale profile

Command Modes

Administration configuration

Command History

Release Modification

Release 3.9.1

This command was introduced.

Release 4.0.1

The l3xl keyword was introduced.

This command was moved to administration configuration mode.

Usage Guidelines

Use the hw-module profile scale command to configure the router to perform more efficiently depending on the use of the router.

  • Specify the scale profile to be default in situations where the router is used as a Layer 2 transport device that requires the router to support high Layer 2 scale numbers.
  • Specify the scale profile to be l3xl in situations where the router is used primarily as a Layer 3 box to provide Layer 3 VPN services. In this case, the router needs to support a high number of Layer 3 routes.

Note


When you upgrade to a release that supports the hw-module profile scale command in adminstration configuration mode, the non-administration configured settings are retained and used. Once you configure the scale profile in the administration plane, it has higher priority than the non-administration plane, and it replaces the non-administration scale profile configuration.


Task ID

Task ID Operation

system

read, write

root-lr

read, write

Examples

The following example shows how to set the scale profile to Layer 3:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module profile 
scale l3

Tue Aug 24 23:52:51.828 UTC
In order to activate this new memory resource profile, 
you must manually reboot the system.
RP/0/RSP0/CPU0:router(admin-config)# commit
  

Related Commands
Related Information

Command

Description

show hw-module profile

Displays the active profiles.

hw-module reset auto

To reset a specific node, use the hw-module reset auto command in administration configuration mode. To disable the reset feature on a specific node, use the no form of this command.

hw-module reset auto [disable] location node-id

no hw-module reset auto [disable] location node-id

Syntax Description

disable

Disables the node reset feature on the specified node.

location node-id

Identifies the node you want to reload. The node-id argument is entered in the rack/slot/module notation.

Command Default

The node reset feature is enabled for all nodes.

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

The hw-module reset auto command is used to reload Cisco IOS XR software on a specific node. The node reloads with the current running configuration and active software set for that node.

Task ID

Task ID

Operations

root-system

read, write

root-lr

read, write

Examples

The following example shows how to reload a node:
RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module reset auto location 0/2/CPU0
  
RP/0/RP0/CPU0:router# RP/0/RP0/CPU0:Apr  2 22:04:43.659 : shelfmgr[294]: 
%S HELFMGR-3-USER_RESET : Node 0/2/CPU0 is reset due to user reload request
  

hw-module subslot reload

To reload Cisco IOS XR software on a specific subslot, use the hw-module subslot reload command in EXEC mode.

hw-module subslot subslot-id reload

Syntax Description

subslot-id

Specifies the subslot to be restarted. The subslot-id argument is entered in the rack/slot/subslot notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

This command reloads Cisco IOS XR software on the specified shared port adapter (SPA) and restarts the SPA interfaces. The SPA reloads with the current running configuration and active software set for the SPA.

Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows how to restart the SPA in slot 2, subslot 1:

RP/0/RSP0/CPU0:router# hw-module subslot 0/2/1 reload
        

led mode

To change the message, mode or status of a router card LED display, use the led mode command in administration configuration mode. To revert to the default message, mode or status, use the no form of this command.

led mode { default | scroll } { lock | unlock } message location node-id

Syntax Description

{default | scroll}

Specifies the mode of the card LED display.

{lock | unlock}

Specifies the status of the card LED display.

message

Specifies the message to display on the card LED.

location node-id

Specifies the node for which to configure the LED information. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Mode: default; status: unlocked; message: according to the state of the software

Command Modes

Administration configuration

Command History

Release Modification

Release 3.8.0

This command was introduced.

Usage Guidelines

You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show led command to display the LED settings for a card or all cards.

Task ID

Task ID Operation

system

read, write

Examples

This example shows how to change the message displayed on the card LED and the subsequent display in the show led command output:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# led mode default unlock STBY_RP location 0/rp0/cpu0
RP/0/RSP0/CPU0:router(admin-config)# end

Uncommitted changes found, commit them? [yes]: 
RP/0/RSP0/CPU0:router(admin)# show led location all | i 0/RP0/CPU0

     LOCATION        MESSAGE        MODE      STATUS 
    ==================================================
        0/0/SP       IOX-RUN       DEFAULT   UNLOCKED
        0/1/SP       IOX-RUN       DEFAULT   UNLOCKED
    0/RP0/CPU0        STBY_RP      DEFAULT   UNLOCKED 
    0/RP1/CPU0       ACTV RP       DEFAULT   UNLOCKED
  

Related Commands

Command

Description

show led

Displays LED information for the router, or for a specific LED location.

power budget enforcement disable

To disable the power budget calculation and allow line cards to boot in an over-budget condition, use the power budget enforcement disable command in administration configuration mode. To enable the power budget calculation once again, use the no form of this command.

power budget enforcement disable

no power budget enforcement disable

Syntax Description

This command has no keywords or arguments.

Command Default

Power budget is enforced.

Command Modes

Administration configuration

Command History

Release Modification
Release 4.0.0

This command was introduced.

Usage Guidelines

The power manager automatically reads the required power supply values from the EEPROM on all cards and calculates the required power budget. The system can power up line cards only if there is sufficient power. Use the power budget enforcement disable command to disable the power budget calculation and to allow the system to boot cards in an over-budget condition.

Use the show environment command with the power option to display the current power current and draw.

If the system is running with a power budget deficiency and the power budget enforcement disable command is not configured, a reset of a line card powers down the line card. Beginning with Cisco IOS XR Release 4.3.1, if you configure the power budget enforcement disable command, behavior is normal even if the system has a power budget deficiency.

Task ID

Task ID Operation

root-system

read, write

Examples

The following example shows how to disable the power management calcuations:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# config
RP/0/RSP0/CPU0:router(admin-config)# power budget enforcement disable
  

Related Commands

Command

Description

show environment

Displays environmental monitor parameters for the system.  

power budget reservation

To release the standby route switch processor (RSP) power budget reservation, use the power budget reservation command in administration configuration mode. To re-reserve the standby RSP power budget reservation, use the no form of this command.

power budget reservation standby-rsp disable

no power budget reservation standby-rsp disable

Syntax Description

standby-rsp disable

Disables the power budget reservation for the standby RSP.

Command Default

Power is reserved for the standby RSP.

Command Modes

Administration configuration

Command History

Release Modification
Release 4.0.0

This command was introduced.

Usage Guidelines

Use the power budget reservation command to disable the power budget reservation for the standby RSP if you only have one RSP installed in the router and you need additional power for other cards. Use the show environment command with the power-supply keyword to view the available power budget on the system.

Task ID

Task ID Operation

root-system

read, write

Examples

The following example shows how to disable the power budget for the standby RSP:

RP/0/RSP1/CPU0:router(admin-config)# power budget reservation standby-rsp disable
  

Related Commands

Command

Description

show environment

Displays environmental monitor parameters for the system.  

redundancy switchover

To cause the primary (active) route processor (RP) to fail over to the redundant standby RP, use the redundancy switchover command in

EXEC or administration EXEC

mode. To disable the forced switchover, use the no form of this command.

redundancy switchover [ location node-id ]

no redundancy switchover [ location node-id ]

Syntax Description

location node-id

(Optional) Specifies the primary RP on which to force a switchover. The node-id argument is expressed in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

Use the redundancy switchover command to trigger a switchover from the primary RP to the standby RP. When the redundancy switchover command is issued, the running (committed) configuration is automatically saved and loaded during switchover, and the standby RP becomes the active primary RP, while the original primary RP becomes the standby RP.


Note


The redundancy switchover command can be used only if the standby RP is in the ready state. Use the show redundancy command to view the status of the RPs.


Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows partial output for a successful redundancy switchover operation:

RP/0/RSP0/CPU0:router# show redundancy
  
  Redundancy information for node 0/RP0/CPU0:
  ==========================================
  Node 0/RP0/CPU0 is in ACTIVE role
  Partner node (0/RP1/CPU0) is in STANDBY role
  Standby node in 0/RP1/CPU0 is ready
  
  Reload and boot info
  ----------------------
  RP reloaded Tue Mar 28 09:02:26 2006: 5 hours, 41 minutes ago
  Active node booted Tue Mar 28 09:02:56 2006: 5 hours, 41 minutes ago
  Last switch-over Tue Mar 28 09:09:26 2006: 5 hours, 34 minutes ago
  Standby node boot Tue Mar 28 09:10:37 2006: 5 hours, 33 minutes ago
  Standby node last went not ready Tue Mar 28 09:25:49 2006: 5 hours, 18 minutes
  go
  Standby node last went ready Tue Mar 28 09:25:51 2006: 5 hours, 18 minutes ago
  There has been 1 switch-over since reload
  ....
RP/0/RSP0/CPU0:router# redundancy switchover
  
  Initializing DDR SDRAM...found 2048 MB
  Initializing ECC on bank 0
  ...
  Turning off data cache, using DDR for first time
  
  Initializing NVRAM...
  Testing a portion of DDR SDRAM ...done
  Reading ID EEPROMs ...
  Initializing SQUID ...
  Initializing PCI ...
  
  PCI0 device[1]: Vendor ID 0x10ee
  
  Configuring MPPs ...
  Configuring PCMCIA slots ...
  --More--
    

If the standby RP is not in the ready state, the switchover operation is not allowed. The following example shows output for a failed redundancy switchover attempt:

RP/0/RSP0/CPU0:router# show redundancy
  
  This node (0/RP0/CPU0) is in ACTIVE role
  Partner node (0/RP1/CPU0) is in UNKNOWN role
  
RP/0/RSP0/CPU0:router# redundancy switchover
  
  Standby card not running; failover disallowed.
  

Related Commands

Command

Description

show redundancy

Displays the status of route processor redundancy.

show canbus

To display statistics regarding the CAN bus, use the show canbus command in administration EXEC mode.

show canbus { client-stats | controller-stats | server-stats } location { all | node-id }

Syntax Description

client-stats

Displays CAN bus client statistics.

controller-stats

Displays CAN bus controller statistics.

server-stats

Displays CAN bus server statistics.

location {all | node-id}

Displays the status of the CAN bus for a specific node or all nodes.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

Use the show canbus command with the server-stats keyword to determine if the revised backplane ID board (BPID-02) is installed in the router.

Task ID

Task ID Operation

sysmgr

read

Examples

The following example illustrates sample output from the show canbus command with the server-stats keyword:

RP/0/RSP0/CPU0:router(admin)# show canbus server-stats location all

       Slot   State Partition-A Rev Partition-B Rev Active-Partition
   0/0/CPU0  Online            2.01            2.02      Partition B
   0/1/CPU0  Online            2.01            2.02      Partition B
   0/2/CPU0 Offline --------------- --------------- ----------------
   0/3/CPU0 Offline --------------- --------------- ----------------
0/RSP0/CPU0  Online            1.01            1.02      Partition B
0/RSP1/CPU0  Online            1.01            1.02      Partition B
   … snip …
   0/FT0/SP  Online            4.00            4.00      Partition A
   0/FT1/SP  Online            4.00            4.00      Partition B
 0/BPID0/SP  Online            7.00            7.00      Partition B     
  

Related Commands

Command

Description

clear plugin slot counts

Clears the running counts of the backplane connector slot plugins.  

show plugin slot counts

Displays cumulative and running counts of card insertions per slot.  

show dsc

To display the current designated shelf controller (DSC) configuration for the shelf or for the system, enter the show dsc command in administration EXEC mode.

show dsc

Command Default

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

For more information about identifying and selecting a DSC on your router, see Cisco ASR 9000 Series Aggregation Services Router Getting Started Guide.

Task ID

Task ID

Operations

system

read

Examples

The following example shows sample output from the show dsc command:


RP/0/RSP0/CPU0:PE44_ASR-9010(admin)# show dsc

Thu Jul 30 02:51:59.628 DST
NODE         ROLE
========================
0/RSP0/CPU0  DSC
  

show environment

To display environmental monitor parameters for the system, use the show environment command in the appropriate mode.

EXEC Mode: show environment [ all | last | leds | table | temperatures | voltages ] [node-id]

Administration EXEC Mode: show environment [ all | fans | last | leds | power-supply | table | temperatures | trace | voltages ] [node-id]

Syntax Description

all

(Optional) Displays information for all environmental monitor parameters.

fans

(Optional) Displays information about the fans.

last

(Optional) Displays the environmental statistics at the time of the last shutdown.

leds

(Optional) Displays monitor parameters for LEDs on all cards in the node.

power

(Optional) Displays power supply voltage and current information.

table

(Optional) Displays environmental parameter ranges.

temperatures

(Optional) Displays system temperature information.

voltages

(Optional) Displays system voltage information.

node-id

(Optional) Node whose information you want to display. The node-id argument is expressed in the rack/slot/module notation.

Command Default

All environmental monitor parameters are displayed.

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

The show environment command displays information about the hardware that is installed in the system, including fans, LEDs, power supply voltage, and current information and temperatures.

Task ID

Task ID

Operations

system

read

Examples

The following example shows sample output from the show environment command with the temperatures keyword:

RP/0/RSP0/CPU0:router# show env temperatures

Sun Aug  8 23:18:15.153 ABC

R/S/I   Modules         Inlet           Hotspot
                        Temperature     Temperature
                        (deg C)         (deg C)
 
0/RSP0/*
        host              21.2           30.8         
0/RSP1/*
        host              20.5           30.3         
0/5/*
        host              23.2           30.9    
  

Table 1 describes the significant fields shown in the display.

Table 1  show environment temperatures Field Descriptions

Field

Description

R/S/I

Rack number, slot number, and interface for which information is displayed, in the format rack/slot/module.

Modules

Module for which temperature information is displayed.

Inlet Temperature (deg C)

Current temperature of the inlet sensor, in degrees Celsius.

Note   

The inlet temperature corresponds to the room air temperature entering the router.

Exhaust Temperature (deg C)

Current temperature of the exhaust sensor, in degrees Celsius.

Note   

The exhaust temperature corresponds to the air being exhausted from the router.

Hotspot Temperature (deg C)

Current temperature of the hotspot, in degrees Celsius.

RP/0/RSP0/CPU0:router# show env leds

Sun Aug  8 23:18:19.416 ABC
R/S/I   Modules LED             Status
0/RSP0/*
        host    Critical-Alarm  Off
        host    Major-Alarm     Off
        host    Minor-Alarm     Off
        host    ACO             Off
        host    Fail            Off
0/RSP1/*
        host    Critical-Alarm  On
        host    Major-Alarm     Off
        host    Minor-Alarm     Off
        host    ACO             Off
        host    Fail            Off
  

Table 2describes the significant fields shown in the display.

Table 2  show environment leds Field Descriptions

Field

Description

rack_num/slot_num/*:

Rack number and slot number where the node resides.

Module (host) LED status says:

Current LED status of the specified node.

The following example shows sample output from the show environment command the with the power-supply keyword:

RP/0/RSP0/CPU0:router(admin)# show environment power-supply

Wed Aug  4 23:38:25.033 DST
R/S/I   Modules         Capacity        Status
                        (W)
0/PM0/*
        host    PM      3000            Ok
0/PM1/*
        host    PM      3000            Ok
0/PM2/*
        host    PM      3000            Ok

R/S/I   Power Draw      Voltage         Current
        (W)             (V)             (A)
0/PM0/* 494.9           53.8            9.2
0/PM1/* 581.0           53.8            10.8
0/PM2/* 0.0             54.1            0.0
--------------
Total:  1075.9

Power Shelves Type: AC

Total Power Capacity:                           9000W
Usable Power Capacity:                          9000W
Supply Failure Protected Capacity:              6000W
Feed Failure Protected Capacity:                3000W
Worst Case Power Used:                          2720W

 Slot                                                      Max Watts
 ----                                                      ---------
 0/1/CPU0                                                        350
 0/RSP0/CPU0                                                     235
 0/RSP1/CPU0                                                     235  (default)
 0/4/CPU0                                                        350
 0/6/CPU0                                                        350
 0/FT0/SP                                                        600
 0/FT1/SP                                                        600

Worst Case Power Available:             6280W
Supply Protected Capacity Available:    3280W
Feed Protected Capacity Available:       280W
  
This table describes the significant fields shown in the display.

Table 3  show environment power-supply Field Descriptions

Field

Description

R/S/I

Rack number, slot number, and interface for which information is displayed, in the format PEM/Power Module/* (for example 0/PM0/*).

Modules

Module for which power information is displayed.

Capacity

Power capacity of each power module in Watts.

Status

Operational status of power modules.

Power Draw

Real (measured) power drawn from each power module.

Voltage

Real (measured) power module voltage.

Current

Real (measured) power module current draw.

Power Shelves Type

AC or DC.

Total Power Capacity

Sum of the power capacity of each of the modules installed in the chassis.

Usable Power Capacity

Sum of the power capacity of each of the powered and operational power modules installed in the chassis.

Supply Failure Protected Capacity

Protected power capacity of the chassis with power module redundancy (ASR 9010 AC 3+3, ASR 9010 DC 5+1, ASR 9006 AC 2+1, ASR 9010 DC 2+1).

Feed Failure Protected Capacity

Feed protected power capacity. This value applies to the ASR 9010 AC system only.

Worst Case Power Used

Sum of the estimated power draw of each of the load modules in the chassis. Load modules can be fan trays, RSPs and line cards.

Worst Case Power Available

Usable power capacity minus the worst case power used.

Supply Protected Capacity Available

Supply failure protected capacity minus the worst case power used.

Feed Protected Capacity Available

Feed failure protected capacity minus the worst case power used.

show fpd package

To display which shared port adapters (SPA) and SPA interface processors (SIPs) are supported with your current Cisco IOS XR software release, which field-programmable device (FPD) image you need for each SPA and SIP, and what the minimum hardware requirements are for the SPA and SIP modules, use the show fpd package command in administration EXEC mode.

show fpd package

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

If there are multiple FPD images for your card, use the show fpd package command to determine which FPD image to use if you only want to upgrade a specific FPD type.

Task ID

Task ID

Operations

sysmgr

read

Examples

The following example shows sample output from the show fpd package command:

RP/0/RP1/CPU0:router(admin)# show fpd package

Thu Jul  7 04:34:48.351 DST

=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                                                 SW      Min Req   Min Req
Card Type            FPD Description            Type Subtype   Version   SW Ver    HW Vers
==================== ========================== ==== ======= =========== ========  =========
A9K-40GE-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONA LC2                lc   rommonA     1.05        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-4T-B             Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-B         Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.09        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONA LC2                lc   rommonA     1.05        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-4T-E             Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-E         Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.09        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-B             Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-B          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-B          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-E             Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.0       0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-E          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-E          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-4T-L             Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-L         Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.09        0.0       0.1  
                     Tomcat LC2                 lc   fpga2       0.16        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-L             Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.0       0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-L          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-700          Can Bus Ctrl (CBC) LC5     lc   cbc         3.05        0.0       0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.0       0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.0       0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.22        0.0       0.1  
                     ROMMONA LC5                lc   rommonA     1.03        0.0       0.1  
                     ROMMONB LC5                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-500          Can Bus Ctrl (CBC) LC5     lc   cbc         3.05        0.0       0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.0       0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.0       0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.22        0.0       0.1  
                     ROMMONA LC5                lc   rommonA     1.03        0.0       0.1  
                     ROMMONB LC5                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-2G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.02        0.0       0.1  
                     CPUCtrl RSP2               lc   cpld2       1.17        0.0       0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.0       0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.0       0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.0       0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.0       0.1  
                     HSBI RSP2                  lc   hsbi        4.00        0.0       0.1  
                     ROMMONA RSP2               lc   rommonA     1.05        0.0       0.1  
                     ROMMONB RSP2               lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-4G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.02        0.0       0.1  
                     CPUCtrl RSP2               lc   cpld2       1.17        0.0       0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.0       0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.0       0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.0       0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.0       0.1  
                     HSBI RSP2                  lc   hsbi        4.00        0.0       0.1  
                     ROMMONA RSP2               lc   rommonA     1.05        0.0       0.1  
                     ROMMONB RSP2               lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-8G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.02        0.0       0.1  
                     CPUCtrl RSP2               lc   cpld2       1.17        0.0       0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.0       0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.0       0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.0       0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.0       0.1  
                     HSBI RSP2                  lc   hsbi        4.00        0.0       0.1  
                     ROMMONA RSP2               lc   rommonA     1.05        0.0       0.1  
                     ROMMONB RSP2               lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
ASR-9010-FAN         Can Bus Ctrl (CBC) FAN     lc   cbc         4.00        0.0       0.1  
----------------------------------------------------------------------------------------------
ASR-9006-FAN         Can Bus Ctrl (CBC) FAN     lc   cbc         5.00        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-10-SLOT    Can Bus Ctrl (CBC) BP2     lc   cbc         7.103       0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-6-SLOT     Can Bus Ctrl (CBC) BP2     lc   cbc         7.103       0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-ISM-100          Can Bus Ctrl (CBC) LC6     lc   cbc        18.05        0.0       0.1  
                     CPUCtrl LC6                lc   cpld1       0.01        0.0       0.1  
                     Maintenance LC6            lc   fpga2       1.00        0.0       0.1  
                     Amistad LC6                lc   fpga1       0.25        0.0       0.20 
                     ROMMONA LC6                lc   rommonA     1.02        0.0       0.1  
                     ROMMONB LC6                lc   rommon      1.02        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-B             CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-E             CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
----------------------------------------------------------------------------------------------
SPA-4XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.0       0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.0       0.100
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.100
----------------------------------------------------------------------------------------------
SPA-2XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.0       0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.0       0.100
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.100
----------------------------------------------------------------------------------------------
SPA-1XCHSTM1/OC3     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.08        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XCHOC48/DS3     SPA I/O FPGA               spa  fpga2       1.00        0.0       0.49 
                     SPA I/O FPGA               spa  fpga3       1.00        0.0       0.52 
                     SPA I/O FPGA               spa  fpga1       1.36        0.0       0.49 
                     SPA ROMMON                 spa  rommon      2.02        0.0       0.49 
----------------------------------------------------------------------------------------------
SPA-2XCHOC12/DS0     SPA FPGA2 swv1.00          spa  fpga2       1.00        0.0       0.0  
                     SPA FPGA swv1.36           spa  fpga1       1.36        0.0       0.49 
                     SPA ROMMON swv2.2          spa  rommon      2.02        0.0       0.49 
----------------------------------------------------------------------------------------------
SPA-8XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-8XCHT1/E1        SPA I/O FPGA               spa  fpga1       2.08        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.140
----------------------------------------------------------------------------------------------
SPA-OC192POS-XFP     SPA FPGA swv1.2 hwv2       spa  fpga1       1.02        0.0       2.0  
----------------------------------------------------------------------------------------------
SPA-2XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC3-POS        SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-10X1GE-V2        SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-V2      SPA FPGA swv1.9            spa  fpga1       1.09        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC3-POS-V2     SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-1X10GE-WL-V2     SPA FPGA swv1.9            spa  fpga1       1.09        0.0       0.0  
----------------------------------------------------------------------------------------------
  
This table describes the significant fields shown in the display:

Table 4  show fpd package Field Descriptions

Field

Description

Card Type

Module part number.

FPD Description

Description of all FPD images available for the SPA.

Type

Hardware type. Possible types can be:

  • spa—Shared port adapter
  • lc—Line card

Subtype

FPD subtype. These values are used in the upgrade hw-module fpd command to indicate a specific FPD image type to upgrade.

SW Version

FPD software version recommended for the associated module running the current Cisco IOS XR software.

Min Req SW Vers

Minimum required FPD image software version to operate the card. Version 0.0 indicates that a minimum required image was not programmed into the card.

Min Req HW Vers

Minimum required hardware version for the associated FPD image. A minimum hardware requirement of version 0.0 indicates that all hardware can support this FPD image version.

This example shows the output display for ASR9912 and ASR9922:

RP/0/RSP0/CPU0:router # show fpd package
=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                                                 SW      Min Req   Min Req
Card Type            FPD Description            Type Subtype   Version   SW Ver    HW Vers
==================== ========================== ==== ======= =========== ========  =========
ASR-9912-BPID2       Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-BPID2       Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-10-SLOT    Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-6-SLOT     Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-SFC110      Can Bus Ctrl (CBC) MTFC    fc   cbc        28.03        0.00      0.1  
                     Fabric Ctrl0 MTFC          fc   fpga7       1.01        0.00      0.1  
                     Can Bus Ctrl (CBC) MTFC    lc   cbc        28.03        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9912-SFC110      Can Bus Ctrl (CBC) SSFC    fc   cbc        32.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          fc   fpga7       1.01        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9010-FAN         Can Bus Ctrl (CBC) FAN     ft   cbc         4.02        0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc         4.02        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9006-FAN         Can Bus Ctrl (CBC) FAN     ft   cbc         5.02        0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc         5.02        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-FAN         Can Bus Ctrl (CBC) MFAN    ft   cbc        29.10        0.00      0.1  
                     Can Bus Ctrl (CBC) MFAN    lc   cbc        29.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9912-FAN         Can Bus Ctrl (CBC) SFAN    ft   cbc        31.03        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9010-FAN-V2      Can Bus Ctrl (CBC) FAN     ft   cbc        29.10        0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc        29.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9001-FAN         Can Bus Ctrl (CBC) FAN     ft   cbc        24.114       0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc        24.114       0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-4T-B             Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-B         Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.10        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-4T-E             Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-E         Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.10        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-B             Can Bus Ctrl (CBC) LC3     lc   cbc         6.07        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-B          Can Bus Ctrl (CBC) LC3     lc   cbc         6.08        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-E             Can Bus Ctrl (CBC) LC3     lc   cbc         6.07        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.00      0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-E          Can Bus Ctrl (CBC) LC3     lc   cbc         6.08        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-4T-L             Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-L         Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.10        0.00      0.1  
                     Tomcat LC2                 lc   fpga2       0.16        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-L             Can Bus Ctrl (CBC) LC3     lc   cbc         6.07        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.00      0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-L          Can Bus Ctrl (CBC) LC3     lc   cbc         6.08        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-700          Can Bus Ctrl (CBC) LC5     lc   cbc         3.06        0.00      0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.00      0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.00      0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.23        0.00      0.1  
                     ROMMONB LC5                lc   rommon      1.04        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-500          Can Bus Ctrl (CBC) LC5     lc   cbc         3.06        0.00      0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.00      0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.00      0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.23        0.00      0.1  
                     ROMMONB LC5                lc   rommon      1.04        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-700-8G       Can Bus Ctrl (CBC) LC5     lc   cbc         3.06        0.00      0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.00      0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.00      0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.23        0.00      0.1  
                     ROMMONB LC5                lc   rommon      1.35        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-2G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.03        0.00      0.1  
                     CPUCtrl RSP2               lc   cpld2       1.18        0.00      0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.00      0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.00      0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.00      0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.00      0.1  
                     ROMMONB RSP2               lc   rommon      1.06        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-4G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.03        0.00      0.1  
                     CPUCtrl RSP2               lc   cpld2       1.18        0.00      0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.00      0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.00      0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.00      0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.00      0.1  
                     ROMMONB RSP2               lc   rommon      1.06        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-8G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.03        0.00      0.1  
                     CPUCtrl RSP2               lc   cpld2       1.18        0.00      0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.00      0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.00      0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.00      0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.00      0.1  
                     ROMMONB RSP2               lc   rommon      1.06        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP440-TR        Can Bus Ctrl (CBC) RSP3    lc   cbc        16.115       0.00      0.1  
                     ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP440-SE        Can Bus Ctrl (CBC) RSP3    lc   cbc        16.115       0.00      0.1  
                     ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-RP-TR       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-RP-SE       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9900-RP-TR       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9900-RP-SE       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR9001-RP           Can Bus Ctrl (CBC) IMRP    lc   cbc        22.114       0.00      0.1  
                     MB CPUCtrl                 lc   fpga2       1.14        0.00      0.0  
                     ROMMONB IM RP              lc   rommon      1.36        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-24x10GE-SE       Can Bus Ctrl (CBC) LC6     lc   cbc        19.109       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.03        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.01        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.07        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-2x100GE-SE       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MOD80-SE         Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-MOD160-SE        Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-24x10GE-TR       Can Bus Ctrl (CBC) LC6     lc   cbc        19.109       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.03        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.01        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.07        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-2x100GE-TR       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MOD80-TR         Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-MOD160-TR        Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-TEST          Can Bus Ctrl (CBC) LC17    lc   cbc        17.214       0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       0.03        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.04        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-36x10GE-SE       Can Bus Ctrl (CBC) LC6     lc   cbc        15.101       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.01        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.00        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.03        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-36x10GE-TR       Can Bus Ctrl (CBC) LC6     lc   cbc        15.101       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.01        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.00        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.03        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-1x100GE-SE       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-1x100GE-TR       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
ASR9001-LC           Can Bus Ctrl (CBC) IMLC    lc   cbc        23.114       0.00      0.1  
                     DB CPUCtrl                 lc   fpga2       1.17        0.00      0.0  
                     EP Gambit                  lc   fpga3       0.08        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       2.07        0.00      0.0  
                     EP Rogue                   lc   fpga6       1.06        0.00      0.0  
                     EP Sage                    lc   fpga7       1.02        0.00      0.0  
                     ROMMONB IM LC              lc   rommon      1.36        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR9001-LC-S         Can Bus Ctrl (CBC) IMLC    lc   cbc        23.114       0.00      0.1  
                     DB CPUCtrl                 lc   fpga2       1.17        0.00      0.0  
                     EP Gambit                  lc   fpga3       0.08        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       2.07        0.00      0.0  
                     EP Rogue                   lc   fpga6       1.06        0.00      0.0  
                     EP Sage                    lc   fpga7       1.02        0.00      0.0  
                     ROMMONB IM LC              lc   rommon      1.36        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-ISM-100          Can Bus Ctrl (CBC) LC6     lc   cbc        18.06        0.00      0.1  
                     CPUCtrl LC6                lc   cpld1       0.01        0.00      0.1  
                     Maintenance LC6            lc   fpga2       2.13        0.00      0.1  
                     Amistad LC6                lc   fpga1       0.33        0.00      0.20 
                     ROMMONB LC6                lc   rommon      1.02        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-3G           ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-24G          ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
SPA-4XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.00      0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.00      0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.00      0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-4XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.00      0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.00      0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.00      0.100
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.100
----------------------------------------------------------------------------------------------
SPA-1XCHSTM1/OC3     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.00      0.0  
                     SPA I/O FPGA               spa  fpga1       1.08        0.00      0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-24CHT1-CE-ATM    SPA T3 Subrate FPGA        spa  fpga2       1.10        0.00      1.0  
                     SPA I/O FPGA               spa  fpga1       2.32        0.00      1.0  
                     SPA ROMMON                 spa  rommon      1.03        0.00      1.0  
----------------------------------------------------------------------------------------------
SPA-2CHT3-CE-ATM     SPA T3 Subrate FPGA        spa  fpga2       1.11        0.00      1.0  
                     SPA I/O FPGA               spa  fpga1       2.22        0.00      1.0  
                     SPA ROMMON                 spa  rommon      1.04        0.00      1.0  
----------------------------------------------------------------------------------------------
SPA-1CHOC3-CE-ATM    SPA OC3 Subrate FPGA       spa  fpga2       2.23        0.00      0.0  
                     SPA I/O FPGA               spa  fpga1       2.23        0.00      2.0  
                     SPA ROMMON                 spa  rommon      1.04        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1XCHOC48/DS3     SPA I/O FPGA               spa  fpga2       1.00        0.00      0.49 
                     SPA I/O FPGA               spa  fpga3       1.00        0.00      0.52 
                     SPA I/O FPGA               spa  fpga1       1.36        0.00      0.49 
                     SPA ROMMON                 spa  rommon      2.02        0.00      0.49 
----------------------------------------------------------------------------------------------
SPA-2XCHOC12/DS0     SPA FPGA2 swv1.00          spa  fpga2       1.00        0.00      0.0  
                     SPA FPGA swv1.36           spa  fpga1       1.36        0.00      0.49 
                     SPA ROMMON swv2.2          spa  rommon      2.02        0.00      0.49 
----------------------------------------------------------------------------------------------
A9K-MPA-20X1GE       EP I/O FPGA                spa  fpga3       0.08        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-2X10GE       EP I/O FPGA                spa  fpga6       1.06        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-4X10GE       EP I/O FPGA                spa  fpga6       1.06        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-2X40GE       EP Sage                    spa  fpga7       1.03        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-1X40GE       EP Sage                    spa  fpga7       1.03        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-8X10GE       EP I/O FPGA                spa  fpga8       0.07        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-8XCHT1/E1        SPA I/O FPGA               spa  fpga1       2.08        0.00      0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.140
----------------------------------------------------------------------------------------------
SPA-OC192POS-XFP     SPA FPGA swv1.2 hwv2       spa  fpga1       1.02        0.00      2.0  
----------------------------------------------------------------------------------------------
SPA-2XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC3-POS        SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-2XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-4XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-10X1GE-V2        SPA FPGA swv1.10           spa  fpga1       1.10        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-V2      SPA FPGA swv1.9            spa  fpga1       1.09        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC3-POS-V2     SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-1X10GE-WL-V2     SPA FPGA swv1.9            spa  fpga1       1.09        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-2XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-3XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC12-ATM-V2    SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------

Note


In the show fpd package command output, the “subtype” column shows the FPDs that correspond with each SPA image. To upgrade a specific FPD with the upgrade hw-module fpd command, replace the fpga-type argument with the appropriate FPD from the “subtype” column, as shown in the following example:

RP/0/RSP0/CPU0:router(admin)# upgrade hw-module fpd fpga2 location 0/3/1 reload


Related Commands

Command

Description

show hw-module fpd

Displays field-programmable device (FPD) compatibility for all modules or a specific module.

upgrade hw-module fpd

Manually upgrades the current field-programmable device (FPD) image package on a module.

show hw-module fpd

To display field-programmable device (FPD) compatibility for all modules or a specific module, use the show hw-module fpd command in the EXEC or administration EXE mode.

show hw-module fpd location { node-id | all }

Syntax Description

location{node-id | all}

Specifies the location of the module. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-port channelized OC-12/DS0 SPA.

Release 4.3.2

Support for Back-plane identification (BPID) nodes.

Usage Guidelines

Task ID

Task ID

Operations

sysmgr

read

root-lr

read

Examples

The following example shows how to display FPD compatibility for all modules in the router:

RP/0/RSP1/CPU0:router# show hw-module fpd location all 

Mon Jun 29 05:38:50.332 PST

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/RSP0/CPU0  A9K-RSP-4G                 4.8   lc   fpga3   0       1.13     No 
                                              lc   fpga1   0       1.5      No 
                                              lc   fpga2   0       1.14     No 
                                              lc   cbc     0       1.2      No 
                                              lc   fpga4   0       1.6      No 
                                              lc   rommon  0       1.0      No 
--------------------------------------------------------------------------------
0/RSP0/CPU0  ASR-9010-FAN               1.0   lc   cbc     1       4.0      No 
--------------------------------------------------------------------------------
0/RSP0/CPU0  ASR-9010-FAN               1.0   lc   cbc     2       4.0      No 
--------------------------------------------------------------------------------
0/1/CPU0     A9K-40GE-B                 1.0   lc   fpga1   0       0.38     No 
                                              lc   fpga2   0       0.8      No 
                                              lc   cbc     0       2.2      No 
                                              lc   cpld1   0       0.15     No 
                                              lc   rommon  0       1.0      No 
--------------------------------------------------------------------------------
0/1/CPU0     A9K-40GE-B                 1.0   lc   fpga1   1       0.38     No 
--------------------------------------------------------------------------------
0/4/CPU0     A9K-8T/4-B                 1.0   lc   fpga1   0       0.38     No 
                                              lc   fpga2   0       0.10     No 
                                              lc   cbc     0       2.2      No 
                                              lc   cpld2   0       0.7      No 
                                              lc   cpld1   0       0.15     No 
                                              lc   cpld3   0       0.3      No 
                                              lc   rommon  0       1.0      No 
                                              lc   fpga3   0      14.42     No 
--------------------------------------------------------------------------------
0/4/CPU0     A9K-8T/4-B                 1.0   lc   fpga1   1       0.38     No 
--------------------------------------------------------------------------------
0/6/CPU0     A9K-4T-B                   1.0   lc   fpga1   0       0.38     No 
                                              lc   fpga2   0       0.10     No 
                                              lc   cbc     0       2.2      No 
                                              lc   cpld2   0       0.7      No 
                                              lc   cpld1   0       0.15     No 
                                              lc   cpld3   0       0.3      No 
                                              lc   rommon  0       1.0      No 
                                              lc   fpga3   0      14.42     No 
--------------------------------------------------------------------------------
0/6/CPU0     A9K-4T-B                   1.0   lc   fpga1   1       0.38     No 
--------------------------------------------------------------------------------
  

BPID nodes can be used as location to display the BPID image information:

RP/0/RSP0/CPU0:router# sh hw-module fpd location 0/bpid0/sp


===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/BPID0/SP   ASR-9912-BPID2             1.0   bp   cbc     11      7.104    No

The following example shows how to display FPD compatibility for a specific module in the router:

RP/0/RSP1/CPU0:router# show hw-module fpd location 0/4/cpu0 

Thu Nov 19 21:43:49.599 UTC
===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/4/CPU0     A9K-SIP-700                1.13  lc   fpga1   0       0.22     No 
                                              lc   cbc     0       3.03     No 
                                              lc   hsbi    0       3.00     No 
                                              lc   rommon  0       1.02     No 
                                              lc   fpga2   0       5.14     No 
                                              lc   cpld1   0       0.14     No 
--------------------------------------------------------------------------------
  
Table 5 show hw-module fpd Field Descriptions

Field

Description

Location

Location of the module in the rack/slot/module notation.

Card Type

Module part number.

HW Version

Hardware model version for the module.

Type

Hardware type. Can be one of the following types:

  • spa—Shared port adapter
  • lc—Line card

Subtype

FPD type. Can be one of the following types:

  • fabldr—Fabric downloader
  • fpga1—Field-programmable gate array
  • fpga2—Field-programmable gate array 2
  • fpga3—Field-programmable gate array 3
  • fpga4—Field-programmable gate array 4
  • fpga5—Field-programmable gate array 5
  • rommonA—Read-only memory monitor A
  • rommon—Read-only memory monitor B

Inst

FPD instance. The FPD instance uniquely identifies an FPD and is used by the FPD process to register an FPD.

Current SW Version

Currently running FPD image version.

Upg/Dng?

Specifies whether an FPD upgrade or downgrade is required. A downgrade is required in rare cases when the version of the FPD image has a higher major revision than the version of the FPD image in the current Cisco IOS XR software package.


Related Commands

Command

Description

show fpd package

Displays which SPAs and SIPs are supported with your current Cisco IOS XR software release, which FPD image you need for each card, and what the minimum hardware requirements are for the various modules.

upgrade hw-module fpd

Manually upgrades the current field-programmable device (FPD) image package on a module.

show hw-module profile

To display the active profiles on the router, use the show hw-module profile command in EXEC mode.

show hw-module profile { all | feature | scale } [ location node-id ]

Syntax Description

all

Displays information regarding all active profiles.

feature

Displays information regarding active feature profiles.

scale

Displays information regarding active scale profiles.

location node-id

Displays the active profile for a particular node.

Command Modes

EXEC

Command History

Release Modification

Release 3.9.1

This command was introduced.

Release 4.0.1

The feature keyword was added.

Usage Guidelines

The show hw-module profile command displays only active profiles. If a profile has been configured and the line card has not be reloaded since the configuration, the profile is not active. Use the show running-config hw-module profile command to view configured profiles.

Task ID

Task ID Operation

root-lr

read

Examples

This example shows sample output from the show hw-module profiles command with the feature keyword:

RP/0/RSP0/CPU0router0# show hw-module profile feature

Thu Dec  9 03:30:42.633 PST

                Node: 0/0/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default

                Node: 0/1/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default

                Node: 0/4/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default

                Node: 0/6/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default
  

Related Commands

Command

Description

hw-module profile feature

Enables a feature bundle on the router.  

hw-module profile scale

Specifies a scale profile for the router.  


Related Commands
Related Information

Command

Description

hw-module profile feature

Enables a feature bundle on the router.

hw-module profile scale

Specifies a scale profile for the router.

show hw-module subslot brief

To display summary information related to a specified internal hardware device on a shared port adapter (SPA), use the show hw-module subslot brief command in

EXEC

mode.

show hw-module subslot [node-id] brief [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.
  • c2w—Displays Cisco-to-wire bus device information.
  • fpga—Displays SPA field-programmable gate array information.
  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)
  • hdlc—Displays SPA hdlc information, where applicable.
  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)
  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)
  • pluggable-optics—Displays pluggable-optics module information.
  • power-margining—Displays power-margining device information.
  • sar—Displays SPA ATM SAR information.
  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)
  • serdes—Displays SPA serializer/deserializer information.
  • spi4—Displays system packet interface level 4.2 bus device information.
  • temperature-sensor—Displays temperature sensor information.
device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot brief command to obtain summary diagnostic information about a device on an interface on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot brief command:

RP/0/RSP0/CPU0:router# show hw-module subslot 0/1/0 brief
  
  Subslot 0/1/0 brief info:
  -----------------------
  SPA inserted: YES
  SPA type:     4xOC3 POS SPA
  SPA operational state: READY
  SPA cfg admin up: YES
      
Table 6 show hw-module subslot config Field Descriptions

Field

Description

SPA inserted

Indicates if a SPA is currently detected in the subslot.

SPA type

Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single height, FHSPA—double height), and optics type.

SPA operational state

Current state of the SPA module.

SPA cfg admin up

Configured state of the SPA: YES—the SPA is not shut down; NO—the SPA is shut down.

show hw-module subslot config

To display information related to configuration of the specified internal hardware device on a shared port adapter (SPA), use the show hw-module subslot config command in EXEC mode.

show hw-module subslot [node-id] config [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.
  • c2w—Displays Cisco-to-wire bus device information.
  • fpga—Displays SPA field-programmable gate array information.
  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)
  • hdlc—Displays SPA hdlc information, where applicable.
  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)
  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)
  • pluggable-optics—Displays pluggable-optics module information.
  • power-margining—Displays power-margining device information.
  • sar—Displays SPA ATM SAR information.
  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)
  • serdes—Displays SPA serializer/deserializer information.
  • spi4—Displays system packet interface level 4.2 bus device information.
  • temperature-sensor—Displays temperature sensor information.
device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Release 5.0.0

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot config command to obtain diagnostic information about the configuration of an interface on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot config command:

RP/0/RSP0/CPU0:router# show hw-module subslot 0/6/cpu0 config

 Thu Feb 19 00:33:02.921 PST 

Subslot 0/6/0 config info:
------------------------
SPA inserted: YES
SPA cfg admin up: YES
SPA cfg power up: YES

Subslot 0/6/1 config info:
------------------------
SPA inserted: YES
SPA cfg admin up: YES
SPA cfg power up: YES

Subslot 0/6/2 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO

Subslot 0/6/3 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO

Subslot 0/6/4 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO

Subslot 0/6/5 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO
  
Table 7  show hw-module subslot config Field Descriptions

Field

Description

SPA inserted

Indicates if a SPA is currently detected in the subslot.

SPA cfg admin up

Configured state of the SPA: YES—the SPA is not shut down; NO—the SPA is shut down.

SPA cfg power up

Indicates whether the subslot is currently configured as powered or not.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot counters

To display statistics related to the processing of internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot counters command in EXEC mode.

show hw-module subslot [node-id] counters [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.
  • c2w—Displays Cisco-to-wire bus device information.
  • fpga—Displays SPA field-programmable gate array information.
  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)
  • hdlc—Displays SPA hdlc information, where applicable.
  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)
  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)
  • pluggable-optics—Displays pluggable-optics module information.
  • power-margining—Displays power-margining device information.
  • sar—Displays SPA ATM SAR information.
  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)
  • serdes—Displays SPA serializer/deserializer information.
  • spi4—Displays system packet interface level 4.2 bus device information.
  • temperature-sensor—Displays temperature sensor information.
device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot counters command to display statistics related to the processing by the specified internal hardware device.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot counters command:

RP/0/RSP0/CPU0:router# show hw-module subslot 0/1/cpu0 counters

Subslot 0/1/0 counts info:
------------------------
SPA inserted: YES
SPA type:     8xGE SPA
SPA operational state: READY
SPA insertion time:  Wed Jan 14 11:33:24 2009
SPA last time ready: Wed Jan 14 11:33:37 2009
SPA uptime [HH:MM:SS]: 852:54:24

Subslot 0/1/1 counts info:
------------------------
SPA inserted: YES
SPA type:     5xGE SPA
SPA operational state: READY
SPA insertion time:  Wed Jan 14 11:33:24 2009
SPA last time ready: Wed Jan 14 11:33:38 2009
SPA uptime [HH:MM:SS]: 852:54:23
 --More--
  
Table 8  show hw-module subslot counters Field Descriptions

Field

Description

SPA inserted

Indicates if a SPA is currently detected in the subslot.

SPA type

Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single height, FHSPA—double height), and optics type.

SPA operational state

Current state of the SPA module.

SPA insertion time

Time the SPA module was last physically inserted or power-cycled.

SPA last time ready

Time the SPA module last changed state to up or ready (the last time the module was loaded or reloaded).

SPA uptime

The time in service or amount of time since the module was last out of service due to a reload, power cycle, or configuration event.

The following example shows sample output for the show hw-module subslot counters command with the framer keyword:

RP/0/RSP0/CPU0:router# show hw-module subslot counters framer
  
  SPA device framer index 0 subindex 0 info:
  
  Milan Framer counters:
  STREAM 0
  Rx Bytes (48-bit) (#0x381fa078-0x883c): 163857232569448
  Rx Good Bytes (48-bit) (#0x381fa080-0x8840): 1964924
  Rx Good Packets (48-bit) (#0x381fa040-0x8820): 26234
  Tx Byte Cnt Reg (48-bit) (#0x381fe070-0xa838): 9375380
  Tx Good Bytes Cnt Reg (48-bit) (#0x381fe068-0xa834): 8909442
  Tx Transmitted Packet Cnt Reg (48-bit) (#0x381fe040-0xa820): 114692
  

show hw-module subslot errors

To display error information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot errors command in

EXEC

mode.

show hw-module subslot [node-id] errors [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.
  • c2w—Displays Cisco-to-wire bus device information.
  • fpga—Displays SPA field-programmable gate array information.
  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)
  • hdlc—Displays SPA hdlc information, where applicable.
  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)
  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)
  • pluggable-optics—Displays pluggable-optics module information.
  • power-margining—Displays power-margining device information.
  • sar—Displays SPA ATM SAR information.
  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)
  • serdes—Displays SPA serializer/deserializer information.
  • spi4—Displays system packet interface level 4.2 bus device information.
  • temperature-sensor—Displays temperature sensor information.
device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot errors command to display error information related to the specified internal hardware device on a SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows partial sample output for the show hw-module subslot errors command:

RP/0/RSP0/CPU0:router# show hw-module subslot 0/1/0 errors

Subslot 0/1/0 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     4xOC3 POS SPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
  Subslot 0/1/1 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     1x10GE XFP SPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
  Subslot 0/1/2 errors info:
  ------------------------
  SPA inserted: NO
  
  Subslot 0/1/3 errors info:
  ------------------------
  SPA inserted: NO
  
  Subslot 0/1/4 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     4xOC48 POS/RPR HHSPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
  Subslot 0/1/5 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     8xGE SPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
   --More--
    
Table 9  show hw-module subslot errors Field Descriptions

Field

Description

Subslot */*/* errors info

SPA for which error information is being displayed. The location of the SPA is expressed in the rack/slot/module notation.

SPA inserted

Indication if a SPA is currently detected in the subslot.

SPA type

Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single-height, FHSPA—double-height), and optics type.

SPA operational state

Current operational state of the SPA module.

SPA last reset reason

Reason for the most recent reset of this SPA.

SPA last failure reason

Reason for the last failure on this SPA.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot plim-subblock

To display SPA firmware information for a shared port adapter (SPA), use the show hw-module subslot plim-subblock command in

EXEC

mode.

show hw-module subslot [node-id] plim-subblock

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

Use the show hw-module subslot plim-subblock command to display SPA firmware information, both kernel and application information, as well as heartbeat and keepalive information. The show hw-module subslot plim-subblock command is mainly used for debugging purposes.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot plim-subblock command:

RP/0/0/CPU0:router# show hw-module subslot 0/5/0 plim-subblock 
   
  Subslot 0/5/0 Plim Subblock Info:
  -------------------------------------
   
  Firmware information: 
    SPA v4.10.1, ifs-spa_ppc_iox.elf
    Application v3.44.0, spa_ct3_pat_apps_iox.tar.gz
   
  SPA keepalive information: 
    Heartbeat check disabled : FALSE
    Keepalive seq 372638, seen 372637, Time since last ipc keep 1s
    

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot registers

To display register information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot registers command in

EXEC

mode.

show hw-module subslot [node-id] registers [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.
  • c2w—Displays Cisco-to-wire bus device information.
  • fpga—Displays SPA field-programmable gate array information.
  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)
  • hdlc—Displays SPA hdlc information, where applicable.
  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)
  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)
  • pluggable-optics—Displays pluggable-optics module information.
  • power-margining—Displays power-margining device information.
  • sar—Displays SPA ATM SAR information.
  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)
  • serdes—Displays SPA serializer/deserializer information.
  • spi4—Displays system packet interface level 4.2 bus device information.
  • temperature-sensor—Displays temperature sensor information.
device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

Use the command to display the nodes on the router.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot registers command to display register information for the specified internal hardware device on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot registers command:

RP/0/RSP0/CPU0:router# show hw-module subslot 0/1/cpu0 registers

 Thu Feb 19 00:38:32.908 PST 

Subslot 0/1/0 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/1 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/2 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/3 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/4 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/5 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A
  
Table 10  show hw-module subslot registers Field Descriptions

Field

Description

SPA hardware ID

SPA hardware identifier in hexadecimal format.

SPA SW FPGA rev.

SPA software field-programmable gate array (FPGA) revision number in hexadecimal format.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot status

To display status information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot status command in EXEC mode.

show hw-module subslot [node-id] status [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.
  • c2w—Displays Cisco-to-wire bus device information.
  • fpga—Displays SPA field-programmable gate array information.
  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)
  • hdlc—Displays SPA hdlc information, where applicable.
  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)
  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)
  • pluggable-optics—Displays pluggable-optics module information.
  • power-margining—Displays power-margining device information.
  • sar—Displays SPA ATM SAR information.
  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)
  • serdes—Displays SPA serializer/deserializer information.
  • spi4—Displays system packet interface level 4.2 bus device information.
  • temperature-sensor—Displays temperature sensor information.
device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.9.0

This command was introduced.

Usage Guidelines

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot status command to obtain status information about an interface on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot status command with the temperature-sensor option:

RP/0/RSP0/CPU0:router# show hw-module subslot 0/2/CPU0 status temperature-sensor
  
   SPA device temperature-sensor index 0 subindex 0 info:
  
  DS1631 (0x0803c2e4) device status:
  temperature = 0x1c80 (28.5 degree C)
  
   SPA device temperature-sensor index 0 subindex 0 info:
  
  DS1631 (0x08063bec) device status:
  temperature = 0x1e00 (30.0 degree C)
    
Table 11  show hw-module subslot status Field Descriptions

Field

Description

DS1631 (0x0803c2e4) device status

Device for which the temperature status is displayed.

temperature = 0x1c80 (28.5 degree C)

Current temperature of the specified device, in hexadecimal format and degrees Celsius.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show inventory

To retrieve and display information about all the Cisco products that are installed in the router, use the show inventory command in EXEC or administration EXEC mode.

EXEC Modeshow inventory [ node-id | all | location { node-id | all } | raw ]

Administration EXEC Modeshow inventory [ node-id | all | chassis | fans | location { node-id | all } | power-supply | raw ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

all

(Optional) Displays inventory information for all the physical entities in the chassis.

location {node-id|all}

(Optional) Displays inventory information for a specific node, or for all nodes in the chassis.

raw

(Optional) Displays raw information about the chassis for diagnostic purposes.

chassis

(Optional) Displays inventory information for the entire chassis.

fans

(Optional) Displays inventory information for the fans.

power-supply

(Optional) Displays inventory information for the power supply.

Command Default

All inventory information for the entire chassis is displayed.

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-port channelized OC-12/DS0 SPA.

Usage Guidelines

If a Cisco entity is not assigned a product ID (PID), that entity is not retrieved or displayed.

Enter the show inventory command with the raw keyword to display every RFC 2737 entity installed in the router, including those without a PID, unique device identifier (UDI), or other physical identification.


Note


The raw keyword is primarily intended for troubleshooting problems with the show inventory command itself.


If any of the Cisco products do not have an assigned PID, the output displays incorrect PIDs, and version ID (VID) and serial number (SN) elements may be missing.

For UDI compliance products, the PID, VID, and SN are stored in EEPROM and NVRAM. Use the show inventory command to display this information.

Examples

The following example shows partial sample output from the show inventory command with the raw keyword:


RP/0/RSP0/CPU0:router# show inventory raw

Tue Jul 28 08:49:14.080 DST
NAME: "module 0/RSP0/CPU0", DESCR: "A2K-RSP-4G-HDD="
PID: A2K-RSP-4G-HDD=   , VID: VP4, SN: FOC1230803H

NAME: "module 0/RSP0/CPU0", DESCR: "RSP Card host "
PID:                   , VID: N/A, SN: 

NAME: "temperature 0/RSP0/CPU0", DESCR: "Inlet Temperature Sensor"
PID:                   , VID: N/A, SN: 

NAME: "temperature 0/RSP0/CPU0", DESCR: "Hot Temperature Sensor"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 0.75VTT"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 0.9VTT_A"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 0.9VTT_B"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - IBV"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 5.0V"
PID:                   , VID: N/A, SN: 

NAME: "module 0/1/CPU0", DESCR: "Cisco ASR 9000 Series SPA Interface Processor-700"
PID: A9K-SIP-700       , VID: P3A, SN: FHH132800F6

NAME: "module 0/1/0"   , DESCR: "10-port 1 GbE Shared Port Adapter V2"
PID: SPA-2XOC12C       , VID: V02, SN: JAE1239W2AI
--More--
  

Table 1 describes the significant fields shown in the display.

Table 12  show inventory Field Descriptions

Field

Description

NAME

Hardware for which the inventory information is displayed. If you are displaying the chassis inventory, this field shows “chassis.” If you are displaying raw inventory, or all inventory information for all nodes in the chassis, this field shows the node name in partially qualified format. For a node, the NAME is expressed in rack/slot/module notation.

DESCR

Describes the chassis or the node.

Chassis descriptions provide the name of the chassis and its Gbps. Node descriptions provide the type of node and its software version.

PID

Physical model name of the chassis or node.

VID

Physical hardware revision of the chassis or node.

SN

Physical serial number for the chassis or node.

show led

To display LED information for the router, or for a specific LED location, use the show led command in EXEC or administration EXEC mode.

show led [ location { node-id | all } ]

Syntax Description

location {node-id | all}

(Optional) Specifies the node for which to display LED information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

Command Default

If no node is specified, information about all LEDs on the router is displayed.

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

Enter the show platform command to see the location of all nodes installed in the router.

Examples

The following example sample output from the show led command with the all keyword:


RP/0/RP0/CPU0:router# show led location all

Thu Jul 30 05:26:24.896 DST
    Location         Message     Mode     Status
  ===================================================
     0/RSP0/*            ACTV   DEFAULT  UNLOCKED
       
       
Table 13  show led location Field Descriptions

Field

Description

LOCATION

Location of the node. LOCATION is expressed in the rack/slot/module notation.

MESSAGE

Current message displayed by the LED.

MODE

Current operating mode of the specified node.

STATUS

Current status of the specified node.


Related Commands
Related Information

Command

Description

led mode

Changes the message, mode or status of a router card LED display.

show operational

To display all operational data provided as XML schema, use the show operational command in

EXEC or administration EXEC

mode.

show operational mda-class [mda-class] [mda-class/naming=value] [descriptive]

Syntax Description

mda-class

Name of the management data API (MDA) class to output. To specify a class name in hierarchy, all classes must be specified from the top of the class to the specific class name that you are interested in. MDA classes are case-sensitive.

To view all available MDA classes, use the question mark (?) online help function.

descriptive

Displays more descriptive information.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-Port Channelized OC-12/DS0 SPA.

Usage Guidelines

Although the show operational command uses the schema database, the command displays the information in a string format like the other show commands. No XML related setups or knowledge is required to use the command.

Task ID

Task ID

Operations

Depends on the MDA class for which you are displaying the information

read

Examples

The following example shows sample output from the show operational command. Not all the output is shown.

RP/0/RSP0/CPU0:router# show operational BGP DefaultVRF GlobalProcessInfo descriptive
[BGP DefaultVRF GlobalProcessInfo]
InStandaloneMode: true[Standalone or Distributed mode]
RouterID: 0.0.0.0[Router ID for the local system]
ConfiguredRouterID: 0.0.0.0[Configured router ID]
LocalAS: 10[Local autonomous system #]
RestartCount: 1[No of times BGP has started]
ISRedistributeIBGPToIGPsEnabled: false[Redistribute iBGP into IGPs enabled]
IsFastExternalFalloverEnabled: true[Fast external fallover enabled]
IsBestpathMissingMEDIsWorstEnabled: false[Bestpath: Treat missing MED as worst]
.
.
.
DefaultLocalPreference: 100[Default local preference]
KeepAliveTime: 60[Default keepalive timer (seconds)]
HoldTime: 180[Default hold timer (seconds)]
GenericScanPeriod: 60[Period (in seconds) of generic scanner runs]
.
.
.
VrfIsActive: true[VRF state ]
VrfName: "default"[Name of the VRF ]
    

This example shows sample output from the show operational command where only the top-level MDA class is specified. Not all of the output is shown.

RP/0/RSP0/CPU0:router# show operational Inventory

Thu Feb 19 00:54:41.251 PST 
[Inventory]
RackTable
  Rack/Number=0
    SlotTable
      Slot/Number=0
        CardTable
          Card/Number=0
            PortSlotTable
              PortSlot/Number=0
                Port
                  BasicAttributes
                    BasicInfo
                      Description: CPU_PORT_0
                      VendorType: 1.3.6.1.4.1.9.12.3.1.10
                      Name: 0/0/SP/0
                      IsFieldReplaceableUnit: false
                      CompositeClassCode: 983040
                BasicAttributes
                  BasicInfo
                    Description: CE Port Slot
                    VendorType: 1.3.6.1.4.1.9.12.3.1.5.115
                    Name: portslot 0/0/SP/0
                    IsFieldReplaceableUnit: false
                    CompositeClassCode: 0
            SensorTable
              Sensor/Number=0
                BasicAttributes
                  BasicInfo
                    Description: Temperature Sensor
                    VendorType: 1.3.6.1.4.1.9.12.3.1.8.42
                    Name: 0/0/* - host - Inlet0
                    CompositeClassCode: 720898
                    EnvironmentalMonitorPath: /admin/oper/inventory/
                     rack/0/entity/0/entity/0/entity/0/entity/0/attrib/
              Sensor/Number=1
                BasicAttributes
                  BasicInfo
                    Description: Temperature Sensor
                    VendorType: 1.3.6.1.4.1.9.12.3.1.8.42
                    Name: 0/0/* - host - Inlet1
                    CompositeClassCode: 720898
                    EnvironmentalMonitorPath: /admin/oper/inventory/
                     rack/0/entity/0/entity/0/entity/0/entity/1/attrib/
              Sensor/Number=2
                BasicAttributes
                  BasicInfo
                    Description: Temperature Sensor
                    VendorType: 1.3.6.1.4.1.9.12.3.1.8.42
                    Name: 0/0/* - host - Exhaust0
                    CompositeClassCode: 720898
 --More--
  

show platform

To display information and status for each node in the system, use the show platform command in EXEC or administration EXEC mode.

show platform [node-id]

Syntax Description

node-id

(Optional) Node for which to display information. The node-id argument is entered in the rack/slot/module notation.

Command Default

Status and information are displayed for all nodes in the system.

Command Modes

Administration EXEC

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-Port Channelized OC-12/DS0 SPA.

Usage Guidelines

The show platform command provides a summary of the nodes in the system, including node type and status.

Enter the show platform command in administration EXEC mode to display output for the entire system. Enter the show platform command in EXEC mode to display output for only those nodes that belong to the SDR on which the command is executed.

Examples

This example shows the sample display output for ASR9912 and ASR9922:

RP/0/RSP0/CPU0:router:router(admin) # show platform
Wed Jul  3 11:34:18.487 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RP0/CPU0      ASR-9922-RP-SE(Active)    IOS XR RUN       PWR,NSHUT,MON
0/RP1/CPU0      ASR-9922-RP-TR(Standby)   IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        FAN TRAY                  READY            
0/FT1/SP        FAN TRAY                  READY            
0/0/CPU0        A9K-36x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/1/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/2/CPU0        A9K-36x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/3/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/4/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/5/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/6/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/7/CPU0        A9K-36x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/8/CPU0        A9K-24x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/9/CPU0        A9K-24x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/PM0/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM1/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM2/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM3/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM4/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM5/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/FC0/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC1/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC2/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC3/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC4/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC5/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC6/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON

The following example shows sample output from the show platform command:

RP/0/RP0/CPU0:router# show platform

Thu Nov 19 21:44:49.274 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP-4G(Active)        IOS XR RUN       PWR,NSHUT,MON
0/RSP1/CPU0     A9K-RSP-4G(Standby)       IN-RESET         PWR,NSHUT,MON
0/1/CPU0        A9K-SIP-700               IOS XR RUN       PWR,NSHUT,NMON
0/1/0           SPA-10X1GE-V2             OK               PWR,NSHUT,MON
0/1/1           SPA-1X10GE-L-V2           OK               PWR,NSHUT,MON
0/3/CPU0        A9K-40GE-B                IOS XR RUN       PWR,NSHUT,MON
0/4/CPU0        A9K-SIP-700               IOS XR RUN       PWR,NSHUT,MON
0/4/1           SPA-2XCHOC12/DS0          OK               PWR,NSHUT,MON
  

The following is sample output for the show platform command with the node-id argument:

RP/0/RSP0/CPU0:router# show platform 0/1/cpu0

Mon Jul 27 22:30:04.752 DST
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/1/CPU0        A9K-40GE-B                IOS XR RUN       PWR,NSHUT,MON
  
This table describes the significant fields shown in the display.

Table 14  show platform Field Descriptions

Field

Description

Node

Identifier of the node in the rack/slot/module notation.

Type

Type of node.

State

Current state of the specified node.

Config State

Current status of the specified node.


Related Commands

Command

Description

show environment

Displays environmental monitor parameters for the system.

show plugin slot counts

To display cumulative and running counts of card inserts per slot, use the show plugin slot counts command in administration EXEC mode.

show plugin slot counts location { all | node-id }

Syntax Description

location {all node-id} Displays plugin slot counts on the designated node or all nodes. The node-id argument is expressed in the rack/slot/module notation.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.9.1

This command was introduced.

Usage Guidelines

Use the show plugin slot counts command to display the number of insertions that have been made to the router backplane for a specific line card or RSP. This command can be used only if the BPID-02 card is installed. If the BPID-02 card is not installed, the following error message is displayed:

Response error: 'ENVMON' detected the 'warning' condition 'Hardware not available'

Task ID

Task ID Operation

sysmgr

read

Examples

This example illustrates sample output from the show plugin slot counts command:

RP/0/RSP0/CPU0:router(admin)# show plugin slot counts location all        

Tue Oct  6 13:37:15.706 pst

Backplane connector slot plugin counters

             Current         Cumulative
0/0/CPU0         176                176
0/1/CPU0          11                 11
0/2/CPU0           0                  0
0/3/CPU0           0                  0
0/RSP0/CPU0        0                  0
0/RSP1/CPU0        1                  1
0/4/CPU0           9                  9
0/5/CPU0           0                  0
0/6/CPU0          12                 12
0/7/CPU0           0                  0
0/FT0/SP           4                  4
0/FT1/SP          14                 14
  

Related Commands

Command

Description

clear plugin slot counts

Clears the running counts of the backplane connector slot plugins.  

show canbus server-stats

Displays the statistics regarding the CAN bus.  

show redundancy

To display the status of route processor redundancy, use the show redundancy command in

EXEC

mode.

show redundancy [ location { node-id | all } | statistics | summary ]

Syntax Description

location {node-id | all}

(Optional) Specifies the node for which to display LED information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

statistics

(Optional) Displays redundancy statistics information.

summary

(Optional) Displays a summary of all redundant node pairs in the router.

Command Default

Route processor redundancy information is displayed for all nodes in the system.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

Use the show redundancy command to display the redundancy status of the route switch processors (RSPs). The show redundancy command also displays the boot and switchover history for the RSPs. To view the nonstop routing (NSR) status of the standby RSPs in the system, use the summary keyword.

Task ID

Task ID

Operations

system

read

basic-services

read (for statistics keyword)

Examples

The following example shows sample output from the show redundancy command:

RP/0/RSP0/CPU0:router# show redundancy location 0/rsp0/cpu0
Thu Jul 30 05:47:12.155 DST
Node 0/RSP0/CPU0 is in ACTIVE role
Node 0/RSP0/CPU0 has no valid partner

Reload and boot info
----------------------
A9K-RSP-4G reloaded Tue Jul 14 15:21:30 2009: 2 weeks, 1 day, 
14 hours, 25 minutes ago
Active node booted Tue Jul 14 15:21:30 2009: 2 weeks, 1 day, 
14 hours, 25 minutes ago

Active node reload "Cause: User initiated forced reload all"
 
Table 15  show redundancy Field Descriptions

Field

Description

Node */*/* is in XXX role

Current role of the primary route processor, where (*/*/*) is the route processor ID in the format rack/slot/module, and XXX is the role of the route processor (active or standby).

In the example, this field shows that the node with the ID 0/RP0/CPU0 is in active role.

Partner node (*/*/*) is in XXX role

Current role of the secondary (or partner) route processor, where (*/*/*) is the route processor ID in the rack/slot/module format, and XXX is the role of the route processor (active or standby).

In the example, this field shows that the node with the ID 0/RP1/CPU0 is in standby role.

Standby node in (*/*/*) is ready

Current state of the standby node, where (*/*/*) is the standby route processor ID.

In the example, the standby node is ready.

Standby node in (*/*/*) is NSR-ready

Current state of the standby node regarding nonstop routing (NSR), where (*/*/*) is the standby route processor ID.

In the example, the standby node is NSR-ready.

Reload and boot info

General overview of the active and standby route processors’ reload and boot history.


Related Commands

Command

Description

redundancy switchover

Causes the primary (active) route processor (RP) to fail over to the redundant standby RP.

show version

To display the configuration of the system hardware, the software version, the names and sources of configuration files, and the boot images, use the show version command in EXEC mode.

show version

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

The show version command displays a variety of system information, including hardware and software version, router uptime, boot settings (configuration register), and active software.

Task ID

Task ID

Operations

basic-services

read

Examples

This example shows partial output from the show version command:

RP/0/RSP0/CPU0:router# show version

Tue Jul 28 05:14:13.670 DST

Cisco IOS XR Software, Version 3.9.0.14I
Copyright (c) 2009 by Cisco Systems, Inc.

ROM: System Bootstrap, Version 1.1(20090521:183759) [ASR9K ROMMON],  

PE44_ASR-9010 uptime is 1 week, 6 days, 13 hours, 52 minutes
System image file is "bootflash:disk0/asr9k-os-mbi-3.9.0.14I/mbiasr9k-rp.vm"

cisco ASR9K Series (MPC8641D) processor with 4194304K bytes of memory.
MPC8641D processor at 1333MHz, Revision 2.2

2 Management Ethernet
12 TenGigE
40 GigabitEthernet
219k bytes of non-volatile configuration memory.
975M bytes of compact flash card.
33994M bytes of hard disk.
1605616k bytes of disk0: (Sector size 512 bytes).
1605616k bytes of disk1: (Sector size 512 bytes).

Configuration register on node 0/RSP0/CPU0 is 0x102
Boot device on node 0/RSP0/CPU0 is disk0:
Package active on node 0/RSP0/CPU0:
asr9k-scfclient, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-scfclient-3.9.0.14I
    Built on Mon Jul 13 08:28:45 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-adv-video, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-adv-video-3.9.0.14I
    Built on Mon Jul 13 10:13:23 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-fpd, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-fpd-3.9.0.14I
    Built on Mon Jul 13 08:44:47 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-diags, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-diags-3.9.0.14I
    Built on Mon Jul 13 08:28:48 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-k9sec, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-k9sec-3.9.0.14I
    Built on Mon Jul 13 08:43:40 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-mgbl, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-mgbl-3.9.0.14I
    Built on Mon Jul 13 10:11:41 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-mcast, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-mcast-3.9.0.14I
    Built on Mon Jul 13 08:40:57 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

 --More--
               
Table 16  show version Field Descriptions

Field

Description

Cisco IOS XR Software, Version #

Cisco IOS XR software version number currently running on the router.

ROM

System bootstrap version number currently running on the router.

router uptime

Number of uninterrupted days, hours, minutes, and seconds the system has been up and running.

System image file is

Location and name of the system image file currently running on the router.

Packet over SONET/SDH network interface(s)

Number of Packet-over-SONET/SDH interfaces available on the current router.

SONET/SDH Port controller(s)

Number of SONET or SDH1 interfaces available on the current router.

Ethernet/IEEE 802.3 interface(s)

Number of Ethernet or IEEE 802.3 interfaces available on the current router.

GigabitEthernet/IEEE interface(s)

Number of Gigabit Ethernet or IEEE 802.3 interfaces available on the current router.

bytes of non-volatile configuration memory

Available volatile configuration memory, in bytes.

bytes of ATA PCMCIA card at disk 0

ATA PCMCIA2 available on the card in disk 0, in bytes.

Package active on node 0/1/SP

Details about the current software package that is running on the SP node in slot 1.

1 SDH = Synchronous Digital Hierarchy
2 ATA PCMCIA = AT Attachment Personal Computer Memory Card Industry Association

upgrade hw-module fpd

To manually upgrade the current field-programmable device (FPD) image package on a module, use the upgrade hw-module fpd command in administration EXEC mode.

upgrade hw-module fpd { all | fabldr | fpga-type | rommon } [ force ] location [ node-id | all ]

Syntax Description

all

Upgrades all FPD images on the selected module.

fabldr

Upgrades the fabric-downloader FPD image on the module.

fpga-type

Upgrades a specific field-programmable gate array (FPGA) image on the module. Use the show fpd package command to view all available FPGA images available for a specific module.

rommon

Upgrades the ROMMON image on the module.

force

(Optional) Forces the update of the indicated FPD image package on a shared port adapter (SPA) that meets the minimum version requirements. Without this option, the manual upgrade upgrades only incompatible FPD images.

location {node-id |all}

Specifies the node for which to upgrade the FPD image. The node-id argument is expressed in the rack/slot/subslot notation. Use the all keyword to indicate all nodes.

Command Default

None

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines


Note


The use of the force option when doing a fpd upgrade is not recommended except under explicit direction from Cisco engineering or TAC.


During the upgrade procedure, the module must be offline (shut down but powered).

Naming notation for the node-id argument is rack/slot/subslot; a slash between values is required as part of the notation.

  • rack —Chassis number of the rack.
  • slot —Physical slot number of the SPA interface processor (SIP).
  • subslot —Subslot number of the SPA.

For more information about the syntax for the router, use the question mark (?) online help function.

When you start the FPD upgrade procedure or log into a router that is running the FPD upgrade procedure, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, reload/configuration change on those 
is not recommended as it might cause HW programming failure and result in RMA 
of the hardware.

 
If you enter administration mode while the FPD upgrade procedure is running, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, reload/configuration change on those 
is not recommended as it might cause HW programming failure and result in RMA 
of the hardware. Do you want to continue? [Confirm (y/n)]

 
If you enter global configuration mode while the FPD upgrade procedure is running, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, configuration change on those is not 
recommended as it might cause HW programming failure and result in RMA of the 
hardware. Do you want to continue? [Confirm (y/n)]

 
When the FPD upgrade global timer expires, the following warning message displayed to the screen.
FPD upgrade has exceeded the maximum time window, the process will terminate now. 
Please check the status of the hardware and reissue the upgrade command if required.

 

Examples

The following example shows how to upgrade the default FPGA on a SPA:


RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# upgrade hw-module fpd fpga location 0/1/4

% RELOAD REMINDER:
  - The upgrade operation of the target module will not interrupt its normal
    operation. However, for the changes to take effect, the target module
    will need to be manually reloaded after the upgrade operation. This can
    be accomplished with the use of "hw-module <target> reload" command.
  - If automatic reload operation is desired after the upgrade, please use
    the "reload" option at the end of the upgrade command.
  - The output of "show hw-module fpd location" command will not display
    correct version information after the upgrade if the target module is
    not reloaded.
Continue? [confirm] y
  
SP/0/1/SP:Dec 22 05:41:17.920 : upgrade_daemon[125]: programming...with file 
/net/node0_RP1_CPU0/asr9k-lc-3.3.83/fpd/ucode/fpga_gladiator_sw0.6.xsvf
SP/0/1/SP:Dec 22 05:41:28.900 : upgrade_daemon[125]: ...programming...
SP/0/1/SP:Dec 22 05:41:28.906 : upgrade_daemon[125]: ...it will take a while...
SP/0/1/SP:Dec 22 05:41:29.004 : upgrade_daemon[125]: ...it will take a while...
SP/0/1/SP:Dec 22 05:43:03.432 : upgrade_daemon[125]: ...programming...
SP/0/1/SP:Dec 22 05:43:03.438 : upgrade_daemon[125]: ...it will take a while...
Successfully upgraded spa fpga instance 4 on location 0/1/4.
  

Related Commands

Command

Description

show fpd package

Displays which SPAs and SIPs are supported with your current Cisco IOS XR software release, which FPD image you need for each card, and what the minimum hardware requirements are for the various modules.

show hw-module fpd

Displays field-programmable device (FPD) compatibility for all modules or a specific module.