Cisco ASR 9000 Series Aggregation Services Router Hardware Installation Guide
Preface
Downloads: This chapterpdf (PDF - 188.0KB) The complete bookPDF (PDF - 53.81MB) | Feedback

Table of Contents

Preface

Audience

Document Conventions

Related Documentation

Changes to This Document

Obtaining Additional Information and Support

Preface

This guide describes how to install a Cisco ASR 9000 Series Aggregation Services Router and its components.

Audience

This guide is written for hardware installers and system administrators of Cisco routers.

This publication assumes that the user has a substantial background in installing and configuring router and switch-based hardware. The reader should also be familiar with electronic circuitry and wiring practices, and have experience as an electronic or electromechanical technician.

Document Conventions


Note Means take note. Notes contain helpful suggestions or references to materials not contained in this manual.



Timesaver Means that the described action saves time. You can save time by performing the action described in the paragraph.



Caution Means be careful. You are capable of doing something that might result in equipment damage or loss of data.


Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, see the Regulatory Compliance and Safety Information document that accompanied this device. Statement 1071


Related Documentation

For more information on the Cisco ASR 9000 Series Aggregation Services Router, refer to the addtional documents at: http://www.cisco.com/c/en/us/support/routers/asr-9000-series-aggregation-services-routers/products-installation-guides-list.html

Changes to This Document

Table 1 lists the technical changes made to this document since it was first created.

 

Table 1 Changes to This Document

Date
Change Summary

October 2012

Information added for Cisco ASR 9922 version 2 fan tray.

June 2014

Information added about installing optional air baffles on the Cisco ASR 9006 Aggregation Services Router.

September 2013

Information added about the Cisco ASR 9904 Aggregation Services Router.

August 2013

Information added about the Cisco ASR 9912 Aggregation Services Router.

May 2013

Information added about the Cisco ASR 9000v satellite shelf adding support for the Cisco CRS Line Card Chassis in either the 8-slot or 16-slot variation.

February 2013

Updates and corrections made to various portions of the document.

December 2012

Information added about the Cisco ASR 9000v satellite shelf adding support for the Cisco ASR 9922 Aggregation Services Router and the Cisco ASR 9001 Aggregation Services Router. Also, information added about the Cisco ASR 901 Series Aggregation Services Router as a satellite shelf and the Cisco ASR 903 Series Aggregation Services Router as a satellite shelf.

September 2012

Information added about the new 1-port 40GE Modular Port Adapter (MPA), 36-port 10GE line card, 1-port 100GE line card, Cisco ASR 9922 Aggregation Services Router, RP card, FC card, and Cisco ASR 9000v satellite shelf (adding support for the A9K-36X10GE-TR [36-port 10GE line card, Packet Transport Optimized] and A9K-36X10GE-SE [36-port 10GE line card, Service Edge Optimized]).

May 2012

Information added about the new Cisco ASR 9000v (a satellite system with the Cisco ASR 9000).

The Cisco ASR 9000v satellite shelf provides 44 1GE SFP ports and 4 10GE SFP+ ports.

December 2011

Information added about the new RSP-440 Route Processor card, the new 24-port 10GE fixed line card, the 2-port 100GE fixed line card, and the modular line card supporting the 20-port 1GE MPA, the 4-port 10GE MPA, and the 2-port 10GE MPA.

Information added about the new version 2 power system. The Cisco ASR 9006 Router and Cisco ASR 9010 Router now support version 1 and version 2 power systems.

May 2010

Added power consumption specifications for the new 16-port 10GE SFP+ line card. Updates and corrections made to various portions of the document.

December 2009

Updates and corrections made to various portions of the document.

March 2009

Initial release of this document.

Obtaining Additional Information and Support

For information on obtaining documentation, submitting a service request to obtain support, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed, and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service, and Cisco currently supports RSS Version 2.0.