Guest

Cisco Services Modules

Connecting the Cisco 6-port GE SFP Service to the Network

  • Viewing Options

  • PDF (710.8 KB)
  • Feedback

Table Of Contents

Connecting the Cisco 6-port GE SFP Service Modules to the Network

Contents

About the Cisco Cisco 6-port GE SFP Service Module

Service Module GE Ports

Service Module LEDs

Conventions

Safety Warnings

Installing and Removing the Cisco SM-X-6X1G on Cisco 4451-X Integrated Services Routers

Software Requirements for the Cisco SM-X-6X1G

Removing the Cisco SM-X-6X1G from a Cisco ISR 4451-X Router

Installing the Cisco SM-X-6X1G in the Cisco ISR 4451-X Router

Verifying Cisco SM-X-6X1G Installation in a Cisco ISR 4451-X Router

Additional References

Related Documents

Technical Assistance


Connecting the Cisco 6-port GE SFP Service Modules to the Network


Last Updated: December 5, 2013
OL-30169-01
  

This document describes how to install a Cisco 6-port GE SFP Service Module and how to connect the service module to your network.

Contents

This guide contains the following sections:

About the Cisco Cisco 6-port GE SFP Service Module

Service Module GE Ports

Service Module LEDs

Conventions

Safety Warnings

Installing and Removing the Cisco SM-X-6X1G on Cisco 4451-X Integrated Services Routers

Additional References

About the Cisco Cisco 6-port GE SFP Service Module

The Cisco SM-X-6X1G are multi gigabit ethernet service modules for the Cisco 4451-X Integrated Services Routers (Cisco ISR 4451-X).

The SM-X-6X1G provides six 1 GB ethernet routing ports. The service module provides the following external interfaces:

Six 10/100/1000 Mbps RJ45 interface with Speed and Link LEDs

Six 1GB SFP interface with Speed and EN LEDs

One SFP+ interface with LNK/ACT and EN LEDs

LED signaling:

Enable LED

Port Link/Status LEDs

Front panel Gigabit Ethernet port

Online insertion and removal (OIR) support

This service module is available in the following SKU:

SM-X-6x1GE—6 port GE SFP Service Module

Figure 1-1 shows the faceplate of the Cisco SM-X-6X1G service module.

Figure 1-1 Cisco SM-X-6X1G Service Module

1. Screws to connect to router chassis

3. LEDs

2. GE Ports

 

Service Module GE Ports

Figure 1-2 shows the various GE ports on the Cisco SM-X-6X1G:

Figure 1-2 Front Ports on the SM-X-6X1G

1. SFP0

8. GE5

2. GE0

9. GE3

3. SFP2

10. SFP3

4. GE2

11. GE1

5. GE4

12. SFP1

6. SFP4

13. LEDs

7. SFP5

 

Service Module LEDs

The Cisco SM-X-6X1G enhanced service module includes several indicator LEDs. Figure 1-4 and Figure 1-4 show the LEDs available on the service module. Table 1 describes the LEDs on the Cisco SM-X-6X1G.

Figure 1-3

Cisco SM-X-6X1G LEDs

Figure 1-4

Cisco SM-X-6X1G LEDs

Table 1 Cisco SM-X-6X1G Service Module LEDs

LED
Color
Description

EN

Solid Green

The module is powered on and is functioning correctly.

Solid Amber

Module has some failure.

Off

Default when module is powered on for the first time. Persistent until changed by the host software.

10/100/1000 GigE link status

Off

No link.

Solid green

Ethernet cable present and link established with the other side.

10/100/1000 GigE link speed

Off

No link.

Blinking

Blink frquency indicates port speed:

1 blink—10 Mbps

2 blinks—100 Mbps

3 blinks—1000 Mbps

SFP S

Off

No link.

Blinking

Blink frquency indicates port speed:

1 blink—10 Mbps

2 blinks—100 Mbps

3 blinks—1000 Mbps

LNK/ACT LED

Off

No link activity

Green

Link is stable with no activity.

Amber

Active media type is SFP, but SFP type is not valid or there is an error in the SFP.

Enable LED Status

Off

One of the following:

Active media type is not SFP

Active media type is SFP but SFP is not present

Solid green

Active media type is SFP, SFP typoe is valid, and there is no error in the SFP.

Blinking green

Link is stable with activity (constant blinking).


Conventions


Note Means reader take note. Notes contain helpful suggestions or references to additional information and material.



Caution This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.


Tip Means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver.



Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning statement to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Safety Warnings


Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Statement 1043

Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Statement 1

Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026

Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037

Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038

Warning To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039

Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Statement 1015

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Warning No user-serviceable parts inside. Do not open. Statement 1073

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection.

T3, E3 Statement 1044

Installing and Removing the Cisco SM-X-6X1G on Cisco 4451-X Integrated Services Routers

This section describes the following tasks for the Cisco SM-X-6X1G enhanced service module:

Software Requirements for the Cisco SM-X-6X1G

Removing the Cisco SM-X-6X1G from a Cisco ISR 4451-X Router

Installing the Cisco SM-X-6X1G in the Cisco ISR 4451-X Router

Verifying Cisco SM-X-6X1G Installation in a Cisco ISR 4451-X Router


Caution Always wear an electrostatic discharge (ESD)-preventive wrist strap and ensure that it makes good contact with your skin when you remove or install a service module (SM). Connect the equipment end of the wrist strap to the metal part of the chassis.


Caution Handle service modules (SMs) by the edges only. SMs are ESD-sensitive components and can be damaged by mishandling.


Caution To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, connect the Gigabit Ethernet ports only to intra-building or unexposed wiring or cable. The intrabuilding cable must be shielded and the shield must be grounded at both ends. The intra-building port(s) of the equipment or subassembly must not be metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.

Software Requirements for the Cisco SM-X-6X1G

Cisco IOS XE Release 3.11S or later release is required to operate the SM-X-6X1G enhanced service module on Cisco ISR 4451-X routers.

To determine the version of Cisco IOS software that is running on your router, log in to the router and enter the show version command:

Router> show version
 
 
Cisco IOS XE Software, Version BLD_V154_1_S_XE311_THROTTLE_LATEST_20131010_070120-std
Cisco IOS Software, ISR4400 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental 
Version 15.4(20131010:090800) 
[v154_1_s_xe311_throttle-BLD-BLD_V154_1_S_XE311_THROTTLE_LATEST_20131010_070120-ios 174]
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 10-Oct-13 05:33 by mcpre
 
 
 
 

Removing the Cisco SM-X-6X1G from a Cisco ISR 4451-X Router

Use the following procedure to remove the Cisco SM-X-6X1G from a Cisco ISR 4451-X Router:


Step 1 Read the "Safety Warnings" section before you perform any module replacement.

Step 2 Locate the service module (SM) to be removed.

Step 3 Using a number 1 Phillips or flat-blade screwdriver, unscrew the captive mounting screws on the module faceplate. See Figure 1-5.

Figure 1-5 Removing a module from the Cisco ISR 4451-X

1. Mounting screws on the module faceplate

 

Step 4 Pull the Cisco SM-X-6X1G out of the chassis.

Step 5 Place the SM in an antistatic bag to protect it from electrostatic discharge (ESD) damage.


Installing the Cisco SM-X-6X1G in the Cisco ISR 4451-X Router

Use the following procedure to install the Cisco SM-X-6X1G on a Cisco ISR 4451-X Router:


Step 1 Read the "Safety Warnings" section before you perform any module replacement.

Step 2 Remove the blank faceplates installed over the slot you intend to use.

Step 3 Push the Cisco SM-X-6X1G into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.

Step 4 Using a number 1 Phillips or flat-blade screwdriver, tighten the captive mounting screws on the module faceplate.


Verifying Cisco SM-X-6X1G Installation in a Cisco ISR 4451-X Router

Use the show diag command to verify that the Cisco SM-X-6X1G has been installed correctly. In the following example, the SM-X-6X1G service module is recognized by the system.

router#show diag ?
  all      All related information
  chassis  Chassis related information
  slot     Slot location information for this command
  subslot  Subslot location information for this command
 
 
Router#show diag subslot 1/0 eeprom detail 
SPA EEPROM data for subslot 1/0:
        EEPROM version           : 4
        Compatible Type          : 0xFF
        Controller Type          : 3012
        Hardware Revision        : 1.0
        PCB Part Number          : 73-15667-04
        Top Assy. Part Number    : 800-40597-01
        Board Revision           : 01
        Deviation Number         : 138372
        Fab Part Number          : 28-11352-04
        Fab Version              : 04
        PCB Serial Number        : FOC173618MY
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product Identifier (PID) : SM-X-6X1G       
        Version Identifier (VID) : V00 
        CLEI Code                : 
        Base MAC Address         : A4 4C 11 CB 13 16 
        MAC Address block size   : 10
        Environment Monitor Data : 40 0B E3 43 00 4B 
        Platform features        : 02 01 01 4B 00 01 01 00 
                                   01 03 00 
 
 

Additional References

Related Documents

Technical Assistance

Related Documents

Related Topic
Document Title

Configuring Cisco SM-X-6X1G Software

Software Configuration Guide for the Cisco 6-port GE SFP Service Module

Regulatory compliance and safety information

Cisco Service Module Regulatory Compliance and Safety Information

Documentation roadmap for the Cisco ISR 4451-X

Documentation Roadmap for the Cisco 4451-X Integrated Services Router


Technical Assistance

Description
Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html