Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide
Safety Warnings, Recommendations, and Tools Required
Downloads: This chapterpdf (PDF - 170.0KB) The complete bookPDF (PDF - 11.67MB) | Feedback

Safety Warnings, Recommendations, and Tools Required

Table Of Contents

Safety Warnings, Recommendations, and Tools Required

General Safety

Maintaining Safety with Electricity

Preventing Electrostatic Discharge

Required Tools and Equipment

Where to Go Next


Safety Warnings, Recommendations, and Tools Required


This chapter describes the safety warnings, recommendations, and tools required to install feature cards in the chassis. This chapter contains the following sections:

General Safety

Maintaining Safety with Electricity

Preventing Electrostatic Discharge

Required Tools and Equipment

Where to Go Next

General Safety

Any device that uses electricity must be handled carefully; follow these guidelines to ensure general safety:

Keep the chassis area clear and dust-free during and after installation.

Put the removed chassis cover in a safe place.

Keep tools away from walk areas where you and others could fall over them.

Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves.

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.


Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040


Maintaining Safety with Electricity


Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43


Follow these guidelines when you work on equipment powered by electricity.

Locate the emergency power-OFF switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn OFF the power.

Before working on the system, unplug the power cord.

Disconnect all power before doing the following:

Installing or removing a feature card

Working near power supplies


Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046


Do not work alone if potentially hazardous conditions exist.

Never assume that power is disconnected from a circuit. Always check.


Warning Read the installation instructions before connecting the system to the power source. Statement 1004


Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, frayed power cords, and missing safety ground connections.

If an electrical accident occurs, proceed as follows:

Use caution; do not become a victim yourself.

Turn OFF power to the system.

If possible, send another person to get medical aid. Otherwise, assess the condition of the victim and then call for help.

Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.


Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors). Statement 13


Preventing Electrostatic Discharge

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures.

Always follow ESD-prevention procedures when you remove and replace components. Ensure that the chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the grounding clip to an unpainted surface of the chassis frame to safely ground unwanted ESD voltages. To guard against ESD damage and shocks, the wrist strap and cord must operate properly. If no wrist strap is available, ground yourself by touching the metal part of the chassis.

For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohm (Mohm).

Required Tools and Equipment

The following items are provided with each universal gateway:

RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL)

RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL)

RJ-45-to-DB-25 male DCE adapter (labeled MODEM)

RJ-45-to-RJ-45 rollover console cable

ESD-preventive wrist strap

Nylon cable tie

Cable tie holder

Grounding lug

Alarm connector

You might need the following equipment, which is not provided with the universal gateway:

Straight-through RJ-45-to-RJ-45 cable for an Ethernet connection

Ethernet hub or PC with a network interface card for Ethernet LAN connections

One breakout cable consisting of a 36-pin connector connected to eight RJ-45 adapters for CT1 or CE1 connections

Straight-through RJ-45-to-RJ-45 cable for CT1 or CE1 connections

75-ohm coaxial cable for a CT3 connection

PC that is running terminal emulation software for local administrative access

Modem for remote administrative access

ESD-preventive mat

Blank feature card panel

Where to Go Next

The remaining chapters of this guide provide information about installing and troubleshooting feature cards and about building cables.

Chapter 2, "Feature Card and Carrier Card Guidelines"

Chapter 3, "T1 and E1 Feature Cards"

Chapter 4, "Channelized T3 Feature Card"

Chapter 5, "Universal Port and Dial-Only Feature Cards"

Chapter 6, "Voice Feature Card"

Chapter 7, "Troubleshooting"

Appendix A, "Cabling Specifications"