Cisco 4000 Series ISRs Software Configuration Guide
Managing Cisco Enhanced Services and Network Interface Modules
Downloads: This chapterpdf (PDF - 1.42 MB) The complete bookPDF (PDF - 4.38 MB) | Feedback

Managing Cisco Enhanced Services and Network Interface Modules

Contents

Managing Cisco Enhanced Services and Network Interface Modules

The router supports Cisco Enhanced Services Modules (SMs) and Cisco Network Interface Modules (NIMs). The modules are inserted into the router using an adapter, or carrier card, into various slots. For more information, see the Hardware Installation Guide for the Cisco 4000 Series Integrated Services Routers.

The following sections are included in this chapter:

Information About Cisco Enhanced Services and Network Interface Modules

The router configures, manages, and controls the supported Cisco Enhanced Services Modules (SMs) and Network Interface Modules (NIMs) using the module management facility built in its architecture. This new centralized module management facility provides a common way to control and monitor all the modules in the system regardless of their type and application. All Cisco Enhanced Service and Network Interface Modules supported on your router use standard IP protocols to interact with the host router. Cisco IOS software uses alien data path integration to switch between the modules.

Modules Supported

For information about the interfaces and modules supported by the Cisco ISR 4400 series and Cisco ISR 4300 series routers, see http:/​/​www.cisco.com/​c/​en/​us/​products/​routers/​4000-series-integrated-services-routers-isr/​relevant-interfaces-and-modules.html.

Network Interface Modules

Cisco Fourth-Generation T1/E1 Voice and WAN Network Interface Module

The Cisco Fourth-Generation T1/E1 Voice and WAN Network Interface Module (NIM) is inserted into the NIM slot of the router and provides data and voice support on T1/E1 trunks. To support voice-related and other DSP features, the Cisco PVDM4 (Cisco Packet Voice Digital Signal Processor Module) is also required. See the following documents for more information:

Cisco SSD/HDD Carrier Card NIM

The router supports a single Cisco SSD and HDD Carrier Card NIM, which must be placed in slot 0 and subslot 1, 2, or 3.

A Cisco SSD/HDD Carrier Card NIM can be one of the following:

  • Cisco SSD Carrier Card NIM—Supports one or two Solid-State Drives (SSDs).

  • Cisco HDD Carrier Card NIM—Supports one Hard Disk Drive (HDD).

For more information on the hardware characteristics of the SSD/HDD Carrier Card NIM, see the Hardware Installation Guide for the Cisco 4000 Series Integrated Services Routers.

For more information on deactivating or reactivating a SSD/HDD Carrier Card NIM, see Deactivating and Reactivating an SSD/​HDD Carrier Card NIM.

Cisco 1-, 2-, and 4-Port Serial NIM

The Cisco 1-, 2-, and 4-port Serial NIMs are multi-protocol synchronous serial network interface modules (NIMs) supported on the Cisco 4400 Series ISRs. The Cisco 1-, 2-, and 4-port Serial NIMs expand the capabilities of the router to provide connectivity for synchronous interfaces in a wide range of applications including up to 8Mbps data rate for high speed high-level data link control (HDLC). These capabilities can be utilized as Point-to-Point Cisco HDLC WAN interface or frame relay interface. The Cisco 1-, 2-, and 4-port Serial NIMs have their own serial communication controllers (SCC) and they do not rely on the host router for SCCs. For further information on configuring this NIM, see the Configuring the Cisco 1-, 2-, and 4-port Serial Network Interface Modules for the Cisco 4400 Series ISRs document.

Upgrading the SSD or HDD Firmware

You can upgrade the firmware for the SSD or HDD using the upgrade hw-programmable module filename bootflash:filename slot/sub-slot command.

A typical filename has the form: nim_ssd_manufacturer_firmware-version-number.bin

The firmware file can also be available in other locations other than bootflash:

For example, you can provide any one of the following locations in place of bootflash:filename:

  • flash:filename

  • harddisk:filename

  • usb1:filename


Note


For a Cisco SSD carrier card NIM or Cisco HDD carrier card NIM, only slot 0 and one of the subslots 1, 2, or 3 must be used.


The following example shows how to upgrade a Micron P400m disk to firmware revision 200 using the upgrade hw-programmable module filename bootflash:filename slot/sub-slot command:

Router# upgrade hw-programmable module filename bootflash:nim_ssd_Micr nP400m_E200.bin
Info: Trying to upgrade Module in 0/3 with nim_ssd_MicronP400m_E200.bin
Info: Current NIM-SSD disk config.
Info: Disk1: rev: 0200 model: MicronP400m-MTFDDAK200MAN
Info: Disk2: rev: 0200 model: MicronP400m-MTFDDAK200MAN
/dev/sde:
fwdownload: xfer_mode=3 min=1 max=255 size=512
............................................................................................................ Done.
/dev/sdf:
fwdownload: xfer_mode=3 min=1 max=255 size=512
............................................................................................................. Done.
Info: Performing post upgrade check ......
Info: Upgrade to Firmware version E200 on disk1 successful.
Info: Upgrade to Firmware version E200 on disk2 successful.
Info: Current NIM-SSD disk config.
Info: Disk1: rev: E200 model: MicronP400m 

Error Monitoring

The drives in the Cisco SDD/HDD Carrier Card NIM are monitored for SMART errors. If a SMART error occurs, a Cisco IOS error message is displayed, as shown in the following example:

%IOSXE-5-PLATFORM:logger: INFO:/dev/sde:SMART error present:please do 
'more bootflash:/tracelogs/smart_errors.log'.

You can find additional information in the error log at: bootflash:/tracelogs/smart_errors.log

Enhanced Service Modules

Cisco SM-1 T3/E3 Service Module

Cisco UCS E-Series Server

For more information, see the documentation listed in the Cisco UCS E-Series Server Roadmap.

Cisco SM-X Layer 2/3 EtherSwitch Service Module

This module provides the following features:

  • Integration of Layer 2 and Layer 3 switching features and the ability of the router to use the Cisco SM-X Layer 2/3 ESM (16-port and 24-port) as an independent Layer 3 switch.

  • 1 Gbps connection to the multigigabit fabric (MGF) for intermodule communication without burdening the CPU of the router.

  • Up to 30 watts of power per port with the robust Power over Ethernet Plus (PoE+) feature along with IEEE 802.3AE Media Access Control Security (MACSec) port-based, hop-to-hop, encryption, and Cisco TrustSec.

For more information, see the following documents:

Cisco 6-Port GE SFP Service Module

The Cisco 6-port GE SFP service module is a Gigabit Ethernet module that can be inserted into the router's SM slot to provide Gigabit Ethernet features on routable external interfaces. For more information about configuring this service module, see the Software Configuration Guide for the Cisco 6-port GE SFP Service Module.

Cisco 4-port GE SFP and 1-port 10 GE SFP Service Module

The Cisco 4-port GE SFP and 1-port 10 GE SFP Service Module (SM-X-4x1GE-1x10GE) is software-configurable high-speed connectivity routing port service module for the Cisco ISR 4400 Series routers. This service module provides increased density of Ethernet interfaces on the Cisco ISR 4400 Series routers. For further information on configuring this service module, see: the Software Configuration Guide for the Cisco 6-port GE SFP Service Module and Cisco 4-port GE SFP and 1-port 10 GE SFP Service Module

Cisco 1GE-CU-SFP and 2GE-CU-SFP Network Interface Modules

The Cisco 1GE-CU-SFP and 2GE-CU-SFP Network Interface Modules (NIMs) are software-configurable high-speed connectivity routing port network interface modules for the Cisco 4000 and Cisco ISR 4300 Series Integrated Services Routers (ISR). These network interface modules provide increased density of Ethernet interfaces on the Cisco 4000 ISR. For further information on configuring this NIM, see the Configuring the Cisco 1GE-CU-SFP and 2GE-CU-SFP Network Interface Modules in Cisco 4000 Series Integrated Services Routers.

Implementing SMs and NIMs on Your Router

Downloading the Module Firmware

Module firmware must be loaded to the router to be able to use a service module. For more information, see Installing a Firmware Subpackage.

The modules connect to the RP via the internal eth0 interface to download the firmware. Initially, the module gets an IP address for itself via BOOTP. The BOOTP also provides the address of the TFTP server used to download the image. After the image is loaded and the module is booted, the module provides an IP address for the running image via DHCP.

Installing SMs and NIMs

For more information, see "Installing and Removing NIMs and SMs" in the Hardware Installation Guide for the Cisco 4000 Series Integrated Services Routers.

Accessing Your Module Through a Console Connection or Telnet

Before you can access the modules, you must connect to the host router through the router console or through Telnet. After you are connected to the router, you must configure an IP address on the Gigabit Ethernet interface connected to your module. Open a session to your module using the hw-module session command in privileged EXEC mode on the router.

To establish a connection to the module, connect to the router console using Telnet or Secure Shell (SSH) and open a session to the switch using the hw-module session slot/subslot command in privileged EXEC mode on the router.

Use the following configuration examples to establish a connection:

  • The following example shows how to open a session from the router using the hw-module session command:

    Router# hw-module session slot/card
    Router# hw-module session 0/1 endpoint 0
     
    Establishing session connect to subslot 0/1
  • The following example shows how to exit a session from the router, by pressing Ctrl-A followed by Ctrl-Q on your keyboard:

    type ^a^q
    picocom v1.4
    
    port is        : /dev/ttyDASH2
    flowcontrol    : none
    baudrate is    : 9600
    parity is      : none
    databits are   : 8
    escape is      : C-a
    noinit is      : no
    noreset is     : no
    nolock is      : yes
    send_cmd is    : ascii_xfr -s -v -l10
    receive_cmd is : rz -vv

Online Insertion and Removal

The router supports online insertion and removal (OIR) of Cisco Enhanced Services Modules and Cisco Network Interface Modules. You can perform the following tasks using the OIR function:

Preparing for Online Removal of a Module

The router supports the OIR of a module, independent of removing another module installed in your router. This means that an active module can remain installed in your router, while you remove another module from one of the subslots. If you are not planning to immediately replace a module, ensure that you install a blank filler plate in the subslot.

Deactivating a Module

A module can be removed from the router without first being deactivated. However, we recommend that you perform a graceful deactivation (or graceful power down) of the module before removing it. To perform a graceful deactivation, use the hw-module subslot slot/subslot stop command in EXEC mode.


Note


When you are preparing for an OIR of a module, it is not necessary to independently shut down each of the interfaces before deactivating the module. The hw-module subslot slot/subslot stop command in EXEC mode automatically stops traffic on the interfaces and deactivates them along with the module in preparation for OIR. Similarly, you do not have to independently restart any of the interfaces on a module after OIR.


The following example shows how to use the show facility-alarm status command to verify if any critical alarm is generated when a module is removed from the system:

Router# show facility-alarm status
System Totals  Critical: 5  Major: 1  Minor: 0

Source                  Severity      Description [Index]
------                  --------      -------------------
Power Supply Bay 1      CRITICAL      Power Supply/FAN Module Missing [0]
GigabitEthernet0/0/0    CRITICAL      Physical Port Link Down [1]
GigabitEthernet0/0/1    CRITICAL      Physical Port Link Down [1]
GigabitEthernet0/0/2    CRITICAL      Physical Port Link Down [1]
GigabitEthernet0/0/3    CRITICAL      Physical Port Link Down [1]
xcvr container 0/0/0    INFO          Transceiver Missing [0]
xcvr container 0/0/1    INFO          Transceiver Missing [0]
xcvr container 0/0/2    INFO          Transceiver Missing [0]
xcvr container 0/0/3    INFO          Transceiver Missing [0]
V: 1.0v PCH R0/18       MAJOR         Volt Above Normal [3]

Note


A critical alarm (Active Card Removed OIR Alarm) is generated even if a module is removed after performing graceful deactivation.


Deactivating Modules and Interfaces in Different Command Modes

You can deactivate a module and its interfaces using the hw-module subslot command in one of the following modes:

  • If you choose to deactivate your module and its interfaces by executing the hw-module subslot slot/subslot shutdown unpowered command in global configuration mode, you are able to change the configuration in such a way that no matter how many times the router is rebooted, the module does not boot. This command is useful when you need to shut down a module located in a remote location and ensure that it does not boot automatically when the router is rebooted.

  • If you choose to use the hw-module subslot slot/subslot stop command in EXEC mode, you cause the module to gracefully shut down. The module is rebooted when the hw-module subslot slot/subslot start command is executed.

To deactivate a module and all of its interfaces before removing the module, use one of the following commands in global configuration mode.

     Command or ActionPurpose
    Step 1 hw-module subslot slot/subslot shutdown unpowered


    Example:
    Router# hw-module subslot 0/2 shutdown unpowered
     

    Deactivates the module located in the specified slot and subslot of the router, where:

    • slot—Specifies the chassis slot number where the module is installed.

    • subslot—Specifies the subslot number of the chassis where the module is installed.

    • shutdown—Shuts down the specified module.

    • unpowered—Removes all interfaces on the module from the running configuration and the module is powered off.

     
    Step 2 hw-module subslot slot/subslot [reload | stop | start]


    Example:
    Router# hw-module subslot 0/2 stop
     

    Deactivates the module in the specified slot and subslot, where:

    • slot—Specifies the chassis slot number where the module is installed.

    • subslot—Specifies the subslot number of the chassis where the module is installed.

    • reload—Stops and restarts the specified module.

    • stop—Removes all interfaces from the module and the module is powered off.

    • start—Powers on the module similar to a physically inserted module in the specified slot. The module firmware reboots and the entire module initialization sequence is executed in the IOSd and Input/Output Module daemon (IOMd) processes.

     

    Deactivating and Reactivating an SSD/HDD Carrier Card NIM

    The following restrictions apply:

    • Deactivating or reactivating an SSD/HDD Carrier Card NIM without an SSD or HDD disk is not supported.

    • Only a single (SSD or HDD) Carrier Card NIM can be plugged into a bay. If you plug an additional (SSD or HDD) Carrier Card NIM into another bay, the module powers down and kernel, log, or error messages are displayed on the Cisco IOS console. In rare cases, the file system may get corrupted on the additional drive.


    Caution


    Deactivation of an SSD/HDD Carrier Card NIM may cause loss of data.

    To deactivate an SSD/HDD Carrier Card NIM, perform the following steps:

       Command or ActionPurpose
      Step 1 virtual-service name


      Example:
      Router(config)# virtual-service my-kwaas-instance
       

      Identifies the kWAAS service (by name), supported on your router, in preparation for the router to be shut down by the no activate command. We recommend that you use this command before reseating or replacing an SSD or HDD.

       
      Step 2 no activate


      Example:
      Router(config-virt-serv)# no activate
       

      Shuts down the kWAAS instance on your router. kWAAS services remain installed. The service will have to be reactivated after the HDD/SSD NIM (module) is restarted.

       
      Step 3 hw-module subslot slot/subslot [reload | stop | start]


      Example:
      Router# hw-module subslot 0/2 stop
      Proceed with stop of module? [confirm]
      Router#
      *Mar 6 15:13:23.997: %SPA_OIR-6-OFFLINECARD: SPA (NIM-SSD) offline in subslot 0/2
      ...
       

      Deactivates or reactivates the module in the specified slot and subslot.

      • slot—The chassis slot number where the module is installed.

      • subslot—The subslot number of the chassis where the module is installed.

      • reload—Deactivates and reactivates (stops and restarts) the specified module.

      • stop—Removes all interfaces from the module and the module is powered off.

      • start—Powers on the module similar to a physically inserted module in the specified slot. The module firmware reboots and the entire module initialization sequence is executed in the IOSd and IOMd processes.

       
      Step 4 Wait for the EN (Enable) LED to turn off, and then remove the SSD/HDD Carrier Card NIM.    

      Reactivating a Module

      If, after deactivating a module using the hw-module subslot slot/subslot stop command, you want to reactivate it without performing an OIR, use one of the following commands (in privileged EXEC mode):

      • hw-module subslot slot/subslot start

      • hw-module subslot slot/subslot reload

      Verifying the Deactivation and Activation of a Module

      When you deactivate a module, the corresponding interfaces are also deactivated. This means that these interfaces will no longer appear in the output of the show interface command.

      1. To verify the deactivation of a module, enter the show hw-module subslot all oir command in privileged EXEC configuration mode.

        Observe the "Operational Status" field associated with the module that you want to verify. In the following example, the module located in subslot 1 of the router is administratively down.

        Router# show hw-module subslot all oir
         
        Module         Model              Operational Status
        
        -------------- ------------------ -------------------------
        
        subslot 0/0    ISR4451-4X1GE      ok
        subslot 1/0    SM-X-T1/E1         ok
        
      2. To verify activation and proper operation of a module, enter the show hw-module subslot all oir command and observe "ok" in the Operational Status field as shown in the following example:

        Router# show hw-module subslot all oir
         
        Module         Model               Operational Status
        
        -------------- ------------------  -------------------------
        
        subslot 0/1    NIM-8MFT-T1/E1      ok
        subslot 1/0    SM-X T1/E1          ok
        
        Router# show platform hardware backplaneswitch-manager R0 status
        slot  bay   port   enable   link status   speed(Mbps)   duplex   autoneg   pause_tx   pause_rx   mtu
        ------------------------------------------------------------------------------------------------------------
        0      0     CP     True      Up           1000          Full    ENABLED    ENABLED    ENABLED   10240
        1      0     GE1    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
        1      0     GE0    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
        2      0     GE1    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
        2      0     GE0    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      1     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      1     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      2     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      2     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      3     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      3     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      4     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      4     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
        0      0     FFP    True       Up         10000          Full    ENABLED    DISABLED   DISABLED  10240
        slot  bay   port            mac    vid   modid     flags - Layer 2
        ------------------------------------------------------------------------------
        0      0    FFP  2c54.2dd2.661b   2351       1              0x20  
        0      0    FFP  2c54.2dd2.661b   2352       1              0x20  
        0      0     CP  2c54.2dd2.661e   2351       0              0xC60  
        0      0     CP  2c54.2dd2.661e   2352       0              0x20  
        1      0    GE0  58bf.ea3a.00f6   2350       0              0x460  
        0      0    FFP  2c54.2dd2.661b   2350       1              0x20  
        1      0    GE0  58bf.ea3a.00f6   2352       0              0x20  
        0      0     CP  2c54.2dd2.661e   2350       0              0x20  
        1      0    GE0  58bf.ea3a.00f6   2351       0              0xC60
        Port block masks: rows=from port, columns=to port, u=unknown unicast, m=unknown multicast, b=broadcast, A=all
        
                   CP    FFP  1/0/1  1/0/0  2/0/1  2/0/0  0/1/1  0/1/0  0/2/1  0/2/0  0/3/1  0/3/0  0/4/1 0/4/0 drops
        -------------------------------------------------------------------------------------------------------------
        CP          -     A     um     um     um     um     um     um     um     um     um     um     um     um     1
        FFP         A     -     -       -      -      -      -      -      -      -      -      -      -      -     0
        1/0/1      um    umb    -     umb    umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     0
        1/0/0      um    umb   umb     -     umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     6
        2/0/1      um    umb   umb    umb     -     umb    umb    umb    umb    umb    umb    umb    umb    umb     0
        2/0/0      um    umb   umb    umb    umb     -     umb    umb    umb    umb    umb    umb    umb    umb     6
        0/1/1      um    umb   umb    umb    umb    umb     -     umb    umb    umb    umb    umb    umb    umb     0
        0/1/0      um    umb   umb    umb    umb    umb    umb      -    umb    umb    umb    umb    umb    umb     0
        0/2/1      um    umb   umb    umb    umb    umb    umb    umb     -     umb    umb    umb    umb    umb     0
        0/2/0      um    umb   umb    umb    umb    umb    umb    umb    umb    -      umb    umb    umb    umb     0
        0/3/1      um    umb   umb    umb    umb    umb    umb    umb    umb    umb     -     umb    umb    umb     0
        0/3/0      um    umb   umb    umb    umb    umb    umb    umb    umb    umb    umb     -     umb    umb     0
        0/4/1      um    umb   umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     -     umb     0
        0/4/0      um    umb   umb    umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     -      0
        
        Port VLAN membership: [untagged vlan] U=untagged T=tagged <VLAN range begin>-<VLAN range end>
        
            CP [2352] U:0001-0001 T:0002-2351 U:2352-2352 T:2353-4095
           FFP [2352] T:0001-4095
         1/0/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         1/0/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         2/0/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         2/0/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/1/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/1/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/2/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/2/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/3/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/3/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/4/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
         0/4/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
        
      show platform hardware backplaneswitch-manager rp active ffp statistics: Example
      Router# show platform hardware backplaneswitch-manager rp active ffp statistics
      Broadcom 10G port(e.g: FFP) status:
                                Rx pkts         Rx Bytes          Tx Pkts         Tx Bytes
      -----------------------------------------------------------------------------------------
      All                             0                0                0                0
        =64                           0                                 0
        65~127                        0                                 0
        128~255                       0                                 0
        256~511                       0                                 0
        512~1023                      0                                 0
        1024~1518                     0                                 0
        1519~2047                     0                                 0
        2048~4095                     0                                 0
        4096~9216                     0                                 0
        9217~16383                    0                                 0
        Max                           0                                 0
      Good                            0                                 0
        CoS 0                                                           0                0
        CoS 1                                                           0                0
        CoS 2                                                           0                0
        CoS 3                                                           0                0
        CoS 4                                                           0                0
        CoS 5                                                           0                0
        CoS 6                                                           0                0
        CoS 7                                                           0                0
        Unicast                       0                                 0
        Multicast                     0                                 0
        Broadcast                     0                                 0
        Control                       0
      Errored
        FCS                           0                                 0
        Undersize                     0
        Ether len                     0
        Fragment                      0                                 0
        Jabber                        0
        MTU ck, good                  0
        MTU ck, bad                   0
        Tx underflow                                                                     0
        err symbol                    0
        frame err                     0
        junk                          0
      Drops
        CoS 0                                                           0                0
        CoS 1                                                           0                0
        CoS 2                                                           0                0
        CoS 3                                                           0                0
        CoS 4                                                           0                0
        CoS 5                                                           0                0
        CoS 6                                                           0                0
        CoS 7                                                           0                0
        STP                           0
        backpress                     0
        congest                       0                0
        purge/cell                    0
        no destination                0
      Pause PFC                       0                                 0
        CoS 0                         0
        CoS 1                         0
        CoS 2                         0
        CoS 3                         0
        CoS 4                         0
        CoS 5                         0
        CoS 6                         0
        CoS 7                         0
      

      Managing Modules and Interfaces

      The router supports various modules. For a list of supported modules, see Modules Supported. The module management process involves bringing up the modules so that their resources can be utilized. This process consists of tasks such as module detection, authentication, configuration by clients, status reporting, and recovery. For detailed information about module configuration, see the module documentation referred to in the Documentation Roadmap for the Cisco 4000 Series Integrated Services Routers.

      For a list of small-form-factor pluggable (SFP) modules supported on your router, see the "Installing and Upgrading Internal Modules and FRUs" section in the Hardware Installation Guide for the Cisco 4000 Series Integrated Services Routers.

      The following sections provide additional information on managing the modules and interfaces:

      Managing Module Interfaces

      After a module is in service, you can control and monitor its module interface. Interface management includes configuring clients with shut or no shut commands and reporting on the state of the interface and the interface-level statistics.

      Monitor the module status and other statistical information using the show commands listed in Monitoring and Troubleshooting Modules and Interfaces.

      Managing Modules and Interfaces Using Backplane Switch

      Backplane Ethernet Switch

      The backplane Ethernet switch on your router provides connectivity to Enhanced Service Modules and Network Interface Modules (NIMs). The backplane Ethernet switch facilitates all packet transfers between the host router and its pluggable modules.

      The backplane Ethernet switch act as a manager for the host router and controls the module and exchanges logical flow-control information with the module to ensure accurate feedback to the router features. See Managing Modules and Interfaces for more information. The backplane Ethernet switch also facilitates control plane traffic flow from the host router to the modules. The backplane switch manages modules and interface cards and is used to communicate with the modules. Module drivers integrate with the backplane switch to configure packet flow and control traffic buffering.

      You are not required to perform any configuration tasks on the backplane switch; all the configurations are performed from the module, which may or may not lead to changes on the backplane switch. For more information on installing an adapter, see the Hardware Installation Guide for the Cisco ISR 4000 Series Integrated Services Routers.


      Note


      Layer 2 protocols, such as the IEEE 802.1D Spanning Tree Protocol (STP), are not supported in the backplane Ethernet switch.


      Viewing Module and Interface Card Status on a Router

      You can view the module and interface card details using the show platform command in privileged EXEC mode.

      The following example shows the sample output for the show platform command:

      Router# show platform
      Chassis type: ISR4451/K9
      
      Slot      Type                State                 Insert time (ago)
      --------- ------------------- --------------------- -----------------
      0         ISR4451/K9          ok                    15:57:33
       0/0      ISR4451-4X1GE       ok                    15:55:24
       0/3      NIM-SSD             ok                    15:55:24
      1         ISR4451/K9          ok                    15:57:33
       1/0      SM-1T3/E3           ok                    15:55:24
      2         ISR4451/K9          ok                    15:57:33
       2/0      SM-1T3/E3           ok                    15:55:24
      R0        ISR4451/K9          ok, active            15:57:33
      F0        ISR4451-FP          ok, active            15:57:33
      P0        Unknown             ps, fail              never
      P1        XXX-XXXX-XX         ok                    15:56:58
      P2        ACS-4450-ASSY       ok                    15:56:58
      
      Slot      CPLD Version        Firmware Version
      --------- ------------------- ---------------------------------------
      0         12090323            15.3(01r)S            [ciscouser-ISRRO...
      1         12090323            15.3(01r)S            [ciscouser-ISRRO...
      2         12090323            15.3(01r)S            [ciscouser-ISRRO...
      R0        12090323            15.3(01r)S            [ciscouser-ISRRO...
      F0        12090323            15.3(01r)S            [ciscouser-ISRRO...
      

      Viewing Backplane Switch Statistics

      Statistics reports for each slot show incoming and outgoing packets or bytes. You can use the information to check traffic flow on the various ports of the backplane switch. The following example shows a sample output for the show platform hardware backplaneswitch-manager rp active summary command:

      Router# show platform hardware backplaneswitch-manager rp active summary
      slot     bay       port         InBytes          InPkts         OutBytes         OutPkts  
      ----------------------------------------------------------------------------------------
         0       0         CP            6242         9361008             6241          403209  
         1       0        GE1               0               0                0               0  
         1       0        GE0            6306          407477             6241         9360934  
         2       0        GE1               0               0                0               0  
         2       0        GE0               0               0                0               0  
         0       1        GE1               0               0                0               0  
         0       1        GE0               0               0                0               0  
         0       2        GE1               0               0                0               0  
         0       2        GE0               0               0                0               0  
         0       3        GE1               0               0                0               0  
         0       3        GE0               0               0                0               0  
         0       4        GE1               0               0                0               0  
         0       4        GE0               0               0                0               0  
         0       0        FFP               0               0                0               0  
         0       0        FFP               0               0                0               0                

      Viewing Backplane Switch Port Statistics

      You can view statistical information related to the port connected to the backplane switch using the show platform hardware backplaneswitch-manager rp active subslot GEO statistics command. The following example displays statistical information related to the backplane switch and ports connected to it:

      Router# show platform hardware backplaneswitch-manager rp active subslot 1/0 GE0 statistics
      Broadcom 1G port(e.g: NIM, ESM, CP) status:
                                Rx pkts         Rx Bytes          Tx Pkts         Tx Bytes
      -----------------------------------------------------------------------------------------
      All                          6306           407477             6241          9360934
        =64                        6237                                72
        65~127                       66                                 3
        128~255                       0                                 0
        256~511                       1                                 3
        512~1023                      2                                 0
        1024~1518                     0                              6163
        1519~2047                     0                                 0
        2048~4095                     0                                 0
        4096~9216                     0                                 0
      Good                         6306                              6241
        CoS 0                                                        6171          9356426
        CoS 1                                                           0                0
        CoS 2                                                           0                0
        CoS 3                                                           0                0
        CoS 4                                                           0                0
        CoS 5                                                           0                0
        CoS 6                                                          70             4508
        CoS 7                                                           0                0
        Unicast                    6294                              6241
        Multicast                     6                                 0
        Broadcast                     6                                 0
        Control                       0                                 0
        VLAN                          0                                 0
      Errored
        FCS                           0                                 0
        Runts                         0                0
        Undersize                     0
        Ether len                     0
        Fragment                      0                                 0
        Jabber                        0                                 0
        MTU                           0
      Drops     
        CoS 0                                                           0                0
        CoS 1                                                           0                0
        CoS 2                                                           0                0
        CoS 3                                                           0                0
        CoS 4                                                           0                0
        CoS 5                                                           0                0
        CoS 6                                                           0                0
        CoS 7                                                           0                0
        STP                           0
        backpress                     0
        congest                       0                0
        purge/cell                    0
        no destination               65
      Pause                           0                                 0
                

      Viewing Slot Assignments

      Use the show inventory command in privileged EXEC mode to view the slot assignments, as shown in the following example:

      Router# show inventory
      NAME: "Chassis", DESCR: "Cisco ISR4451 Chassis"
      PID: ISR4451/K9        , VID: V01, SN: FGL163910CM
      
      NAME: "Power Supply Module 1", DESCR: "Cisco 4451-X ISR 450W AC Power Supply"
      PID: XXX-XXXX-XX       , VID: XXX, SN: DCA1623X05N
      
      NAME: "Fan Tray", DESCR: "Cisco 4451-X ISR Fan tray"
      PID: ACS-4450-FANASSY  , VID:    , SN:            
      
      NAME: "module 0", DESCR: "Cisco ISR4451 Built-In NIM controller"
      PID: ISR4451/K9        , VID:    , SN:          
        
      NAME: "NIM subslot 0/1", DESCR: " NIM-1MFT-T1/E1 - T1/E1 Serial Module"
      PID:  NIM-1MFT-T1/E1  , VID: V01, SN: FOC16254E71
      
      NAME: "subslot 0/1 db module 0", DESCR: "PVDM4-TDM-280 Voice DSP Module"
      PID: PVDM4-TDM-280     , VID: V01, SN: FOC16290GRT
      
      NAME: "NIM subslot 0/0", DESCR: "Front Panel 4 ports Gigabitethernet Module"
      PID: ISR4451-X-4x1GE   , VID: V01, SN: JAB092709EL
      
      NAME: "module 1", DESCR: "Cisco ISR4451 Built-In SM controller"
      PID: ISR4451/K9        , VID:    , SN:            
      
      NAME: "module 2", DESCR: "Cisco ISR4451 Built-In SM controller"
      PID: ISR4451/K9        , VID:    , SN:            
      
      NAME: "SM subslot 2/0", DESCR: "SM-X-1T3/E3 - Clear T3/E3 Serial Module"
      PID: SM-1T3/E3         , VID: V01, SN: FOC15495HSE
      
      NAME: "module R0", DESCR: "Cisco ISR 4451-X Route Processor"
      PID: ISR4451/K9        , VID: V01, SN: FOC163679GH
      
      NAME: "module F0", DESCR: "Cisco ISR4451-X Forwarding Processor"
      PID: ISR4451/K9        , VID:    , SN:            
       

      Monitoring and Troubleshooting Modules and Interfaces

      Use the following commands in global configuration mode to monitor and troubleshoot the modules and interfaces:

      • show platform

      • show platform software backplaneswitch-manager RP [active [detail]]

      • show platform hardware backplaneswitch-manager RPactive CP statistics

      • show platform hardware backplaneswitch-manager RP active summary

      • show platform hardware backplaneswitch-manager [R0 [status] | RP]

      • show diag all eeprom details

      show platform

      Router# show platform
      Chassis type: ISR4451/K9
      
      Slot      Type                State                 Insert time (ago)
      --------- ------------------- --------------------- -----------------
      0         ISR4451/K9          ok                    15:57:33
       0/0      ISR4451-4X1GE       ok                    15:55:24
      1         ISR4451/K9          ok                    15:57:33
       1/0      SM-1T3/E3           ok                    15:55:24
      2         ISR4451/K9          ok                    15:57:33
       2/0      SM-1T3/E3           ok                    15:55:24
      R0        ISR4451/K9          ok, active            15:57:33
      F0        ISR4451-FP          ok, active            15:57:33
      P0        Unknown             ps, fail              never
      P1        XXX-XXXX-XX         ok                    15:56:58
      P2        ACS-4450-FANASSY    ok                    15:56:58
      
      Slot      CPLD Version        Firmware Version
      --------- ------------------- ---------------------------------------
      0         12090323            15.3(01r)S            [ciscouser-ISRRO...
      1         12090323            15.3(01r)S            [ciscouser-ISRRO...
      2         12090323            15.3(01r)S            [ciscouser-ISRRO...
      R0        12090323            15.3(01r)S            [ciscouser-ISRRO...
      F0        12090323            15.3(01r)S            [ciscouser-ISRRO...
      Table 1  show platform Field Descriptions

      Field

      Description

      Slot

      Slot number

      Type

      Type of module

      State

      Status of module

      Insert Time

      Time since the module has been up and running

      show platform software backplaneswitch-manager RP [active [detail]]

      Router# show platform software backplaneswitch-manager RP active detail
      BSM Software Display
      
       module port   port type  alien type    traf type  
      -------------------------------------------------
             0/1/0        NGIO       TRUNK         NGIO  
             0/1/1        NGIO       TRUNK         NGIO  
             0/2/0        NGIO       TRUNK         NGIO  
             0/2/1        NGIO       TRUNK         NGIO  
             0/3/0        NGIO       TRUNK         NGIO  
             0/3/1       ALIEN       TRUNK         NGIO  
             0/4/0        NGIO       TRUNK         NGIO  
             0/4/1        NGIO       TRUNK         NGIO  
             1/0/0        NGIO       TRUNK         NGIO  
             1/0/1        NGIO       TRUNK         NGIO  
             2/0/0        NGIO       TRUNK         NGIO  
             2/0/1        NGIO       TRUNK         NGIO  
      

      show platform hardware backplaneswitch-manager RPactive CP statistics

      Router# show platform hardware backplaneswitch-manager RP active CP statistics
      Broadcom 1G port(e.g:  NIM, NGSM, CP) status:
                                Rx pkts         Rx Bytes          Tx Pkts         Tx Bytes
      -----------------------------------------------------------------------------------------
      All                          6242          9361008             6241           403209
        =64                          72                              6178
        65~127                        4                                60
        128~255                       0                                 0
        256~511                       3                                 1
        512~1023                      0                                 2
        1024~1518                  6163                                 0
        1519~2047                     0                                 0
        2048~4095                     0                                 0
        4096~9216                     0                                 0
      Good                         6242                              6241
        CoS 0                                                           0                0
        CoS 1                                                           0                0
        CoS 2                                                           0                0
        CoS 3                                                        6241           403209
        CoS 4                                                           0                0
        CoS 5                                                           0                0
        CoS 6                                                           0                0
        CoS 7                                                           0                0
        Unicast                    6241                              6235
        Multicast                     1                                 0
        Broadcast                     0                                 6
        Control                       0                                 0
        VLAN                          0                                 0
      Errored
        FCS                           0                                 0
        Runts                         0                0
        Undersize                     0
        Ether len                     0
        Fragment                      0                                 0
        Jabber                        0                                 0
        MTU                           0
      Drops     
        CoS 0                                                           0                0
        CoS 1                                                           0                0
        CoS 2                                                           0                0
        CoS 3                                                           0                0
        CoS 4                                                           0                0
        CoS 5                                                           0                0
        CoS 6                                                           0                0
        CoS 7                                                           0                0
        STP                           0
        backpress                     0
        congest                       0                0
        purge/cell                    0
        no destination                1
      Pause                           0                                 0

      show platform hardware backplaneswitch-manager RP active summary

      Router# show platform hardware backplaneswitch-manager RP active summary
        slot     bay          port           InBytes            InPkts         OutBytes  OutPkts  
      ------------------------------------------------------------------------------------------
           0       0            CP               242                 0                 0   0  
           1       0           GE1                 0                 0                 0   0  
           1       0           GE0                 0                 0                 0   0  
           2       0           GE1                 0                 0                 0   0  
           2       0           GE0                 0                 0                 0   0  
           0       1           GE1                 0                 0                 0   0  
           0       1           GE0                 0                 0                 0   0  
           0       2           GE1                 0                 0                 0   0  
           0       2           GE0                 0                 0                 0   0  
           0       3           GE1                 0                 0                 0   0  
           0       3           GE0                 0                 0                 0   0  
           0       4           GE1                 0                 0                 0   0  
           0       4           GE0                 0                 0                 0   0  
           0       0           FFP                 0                 0                 0   0  

      show platform hardware backplaneswitch-manager [R0 [status] | RP]

      Router# show platform hardware backplaneswitch-manager R0 status
      slot  bay   port   enable   link status   speed(Mbps)   duplex   autoneg   pause_tx   pause_rx   mtu
      ------------------------------------------------------------------------------------------------------------
      0      0     CP     True      Up           1000          Full    ENABLED    ENABLED    ENABLED   10240
      1      0     GE1    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
      1      0     GE0    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
      2      0     GE1    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
      2      0     GE0    True      Up           1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      1     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      1     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      2     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      2     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      3     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      3     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      4     GE1    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      4     GE0    True     Down          1000          Full    DISABLED   ENABLED    ENABLED   10240
      0      0     FFP    True       Up         10000          Full    ENABLED    DISABLED   DISABLED  10240
      slot  bay   port            mac    vid   modid     flags - Layer 2
      ------------------------------------------------------------------------------
      0      0    FFP  2c54.2dd2.661b   2351       1              0x20  
      0      0    FFP  2c54.2dd2.661b   2352       1              0x20  
      0      0     CP  2c54.2dd2.661e   2351       0              0xC60  
      0      0     CP  2c54.2dd2.661e   2352       0              0x20  
      1      0    GE0  58bf.ea3a.00f6   2350       0              0x460  
      0      0    FFP  2c54.2dd2.661b   2350       1              0x20  
      1      0    GE0  58bf.ea3a.00f6   2352       0              0x20  
      0      0     CP  2c54.2dd2.661e   2350       0              0x20  
      1      0    GE0  58bf.ea3a.00f6   2351       0              0xC60
      Port block masks: rows=from port, columns=to port, u=unknown unicast, m=unknown multicast, b=broadcast, A=all
      
                 CP    FFP  1/0/1  1/0/0  2/0/1  2/0/0  0/1/1  0/1/0  0/2/1  0/2/0  0/3/1  0/3/0  0/4/1 0/4/0 drops
      -------------------------------------------------------------------------------------------------------------
      CP          -     A     um     um     um     um     um     um     um     um     um     um     um     um     1
      FFP         A     -     -       -      -      -      -      -      -      -      -      -      -      -     0
      1/0/1      um    umb    -     umb    umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     0
      1/0/0      um    umb   umb     -     umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     6
      2/0/1      um    umb   umb    umb     -     umb    umb    umb    umb    umb    umb    umb    umb    umb     0
      2/0/0      um    umb   umb    umb    umb     -     umb    umb    umb    umb    umb    umb    umb    umb     6
      0/1/1      um    umb   umb    umb    umb    umb     -     umb    umb    umb    umb    umb    umb    umb     0
      0/1/0      um    umb   umb    umb    umb    umb    umb      -    umb    umb    umb    umb    umb    umb     0
      0/2/1      um    umb   umb    umb    umb    umb    umb    umb     -     umb    umb    umb    umb    umb     0
      0/2/0      um    umb   umb    umb    umb    umb    umb    umb    umb    -      umb    umb    umb    umb     0
      0/3/1      um    umb   umb    umb    umb    umb    umb    umb    umb    umb     -     umb    umb    umb     0
      0/3/0      um    umb   umb    umb    umb    umb    umb    umb    umb    umb    umb     -     umb    umb     0
      0/4/1      um    umb   umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     -     umb     0
      0/4/0      um    umb   umb    umb    umb    umb    umb    umb    umb    umb    umb    umb    umb     -      0
      
      Port VLAN membership: [untagged vlan] U=untagged T=tagged <VLAN range begin>-<VLAN range end>
      
          CP [2352] U:0001-0001 T:0002-2351 U:2352-2352 T:2353-4095
         FFP [2352] T:0001-4095
       1/0/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       1/0/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       2/0/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       2/0/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/1/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/1/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/2/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/2/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/3/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/3/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/4/1 [2352] T:0002-2351 U:2352-2352 T:2353-4095
       0/4/0 [2352] T:0002-2351 U:2352-2352 T:2353-4095
      

      show diag all eeprom details

      Router# show diag all eeprom details
      MIDPLANE EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              PCB Serial Number        : FOC15520B7L
              Controller Type          : 1902
              Hardware Revision        : 1.0
              PCB Part Number          : 73-13854-02
              Top Assy. Part Number    : 800-36894-01
              Board Revision           : 05
              Deviation Number         : 123968
              Fab Version              : 02
              Product Identifier (PID) : ISR4451/K9
              Version Identifier (VID) : V01
              CLEI Code                : TDBTDBTDBT
              Processor type           : D0
              Chassis Serial Number    : FGL1601129D
              Chassis MAC Address      : 30f7.0d53.c7e0
              MAC Address block size   : 144
              Manufacturing Test Data  : 00 00 00 00 00 00 00 00
              Asset ID                 : P1B-R2C
      Power/Fan Module P0 EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              Controller Type          : 1509
              Unknown Field (type 00DF): 1.85.1.236.1
              Deviation Number         : 0
              PCB Serial Number        : DCA1547X037
              RMA Test History         : 00
              RMA Number               : 0-0-0-0
              RMA History              : 00
              Version Identifier (VID) : XXX
              Product Identifier (PID) : XXX-XXXX-XX
              CLEI Code                : 0000000000
              Environment Monitor Data : 41 01 C2 42 00 05 F8 00
                                         50 01 F4 1B 58 03 E8 1F
                                         4A 05 DC 21 34 07 D0 21
                                         FC 09 C4 22 60 0B B8 22
                                         92 0D AC 22 D8 0F A0 22
                                         F8 11 94 22 F6 13 88 23
                                         3C 15 7C 23 28 17 70 23
                                         00 19 64 22 D8 1B 58 22
                                         C4 1D 4C 22 BA 1F 40 22
                                         A6 21 34 22 9C 23 28 22
                                         92 25 1C 22 88 27 10 22
                                         60
              Board Revision           : P0
      Power/Fan Module P1 EEPROM data is not initialized
      
      Power/Fan Module P2 EEPROM data is not initialized
      
      Slot R0 EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              PCB Serial Number        : FOC15520B7L
              Controller Type          : 1902
              Hardware Revision        : 1.0
              PCB Part Number          : 73-13854-02
              Top Assy. Part Number    : 800-36894-01
              Board Revision           : 05
              Deviation Number         : 123968
              Fab Version              : 02
              Product Identifier (PID) : ISR4451/K9
              Version Identifier (VID) : V01
              CLEI Code                : TDBTDBTDBT
              Processor type           : D0
              Chassis Serial Number    : FGL1601129D
              Chassis MAC Address      : 30f7.0d53.c7e0
              MAC Address block size   : 144
              Manufacturing Test Data  : 00 00 00 00 00 00 00 00
              Asset ID                 : P1B-R2C
              Asset ID                 :
      Slot F0 EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              Controller Type          : 3567
              Hardware Revision        : 4.1
              PCB Part Number          : 73-12387-01
              MAC Address block size   : 15
              Chassis MAC Address      : aabb.ccdd.eeff
              Product Identifier (PID) : ISR4451-FP
              Version Identifier (VID) : V00
              PCB Serial Number        : FP123456789
              Asset ID                 :
      Slot 0 EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              Controller Type          : 1612
              Hardware Revision        : 4.1
              PCB Part Number          : 73-12387-01
              MAC Address block size   : 15
              Chassis MAC Address      : aabb.ccdd.eeff
              Product Identifier (PID) : ISR4451-NGSM
              Version Identifier (VID) : V00
              PCB Serial Number        : NGSM1234567
              Asset ID                 :
      Slot 1 EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              Controller Type          : 1612
              Hardware Revision        : 4.1
              PCB Part Number          : 73-12387-01
              MAC Address block size   : 15
              Chassis MAC Address      : aabb.ccdd.eeff
              Product Identifier (PID) : ISR4451-NGSM
              Version Identifier (VID) : V00
              PCB Serial Number        : NGSM1234567
              Asset ID                 :
      Slot 2 EEPROM data:
      
              EEPROM version           : 4
              Compatible Type          : 0xFF
              Controller Type          : 1612
              Hardware Revision        : 4.1
              PCB Part Number          : 73-12387-01
              MAC Address block size   : 15
              Chassis MAC Address      : aabb.ccdd.eeff
              Product Identifier (PID) : ISR4451-NGSM
              Version Identifier (VID) : V00
              PCB Serial Number        : NGSM1234567
              Asset ID                 :
      SPA EEPROM data for subslot 0/0:
      
              EEPROM version           : 5
              Compatible Type          : 0xFF
              Controller Type          : 1902
              Hardware Revision        : 2.2
              Boot Timeout             : 400 msecs
              PCB Serial Number        : JAB092709EL
              PCB Part Number          : 73-8700-01
              PCB Revision             : A0
              Fab Version              : 01
              RMA Test History         : 00
              RMA Number               : 0-0-0-0
              RMA History              : 00
              Deviation Number         : 78409
              Product Identifier (PID) : ISR4451-4X1GE
              Version Identifier (VID) : V01
              Top Assy. Part Number    : 68-2236-01
              Top Assy. Revision       : A0
              IDPROM Format Revision   : 36
              System Clock Frequency   : 00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00
              CLEI Code                : CNUIAHSAAA
              Base MAC Address         : 00 00 00 00 00 00
              MAC Address block size   : 0
              Manufacturing Test Data  : 00 00 00 00 00 00 00 00
              Field Diagnostics Data   : 00 00 00 00 00 00 00 00
              Calibration Data         : Minimum: 0 dBmV, Maximum: 0 dBmV
                    Calibration values :
              Power Consumption        : 13100 mWatts (Maximum)
              Environment Monitor Data : 03 30 0C E4 46 32 09 C4
                                         46 32 05 DC 46 32 05 DC
                                         46 32 00 00 00 00 00 00
                                         00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00 00 00
                                         00 00 FE 02 F9 6E
              Processor Label          : 00 00 00 00 00 00 00
              Platform features        : 00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00 00 00
                                         00 00 00 00 00 00 00
              Asset ID                 :
              Asset Alias              :
      SPA EEPROM data for subslot 0/1 is not available
      
      SPA EEPROM data for subslot 0/2 is not available
      
      SPA EEPROM data for subslot 0/3 is not available
      
      SPA EEPROM data for subslot 0/4 is not available
      
      SPA EEPROM data for subslot 1/0 is not available
      
      SPA EEPROM data for subslot 1/1 is not available
      
      SPA EEPROM data for subslot 1/2 is not available
      
      SPA EEPROM data for subslot 1/3 is not available
      
      SPA EEPROM data for subslot 1/4 is not available
      
      SPA EEPROM data for subslot 2/0 is not available
      
      SPA EEPROM data for subslot 2/1 is not available
      
      SPA EEPROM data for subslot 2/2 is not available
      
      SPA EEPROM data for subslot 2/3 is not available
      
      SPA EEPROM data for subslot 2/4 is not available

      Configuration Examples

      This section provides examples of deactivating and activating modules.

      Deactivating a Module Configuration: Example

      You can deactivate a module to perform OIR of that module. The following example shows how to deactivate a module (and its interfaces) and remove power to the module. In this example, the module is installed in subslot 0 of the router.

      Router(config)# hw-module slot 1 subslot 1/0 shutdown unpowered

      Activating a Module Configuration: Example

      You can activate a module if you have previously deactivated it. If you have not deactivated a module and its interfaces during OIR, then the module is automatically reactivated upon reactivation of the router.

      The following example shows how to activate a module. In this example, the module is installed in subslot 0, located in slot 1 of the router:

      Router(config)# hw-module slot 1 subslot 1/0 start