Cisco 3900 Series, 2900 Series, and 1900 Series Integrated Services Routers Software Configuration Guide
Configuring Ethernet CFM and Y.1731 Performance Monitoring on Layer 3 Interfaces
Downloads: This chapterpdf (PDF - 538.0KB) | Feedback

Table Of Contents

Configuring Ethernet CFM and Y.1731 Performance Monitoring on Layer 3 Interfaces

Configuring a Network Interface Device on the L3 Interface

Configuring the NID

Configuration Example

Verifying the NID Configuration

Troubleshooting the NID Configuration

Ethernet Data Plane Loopback

Restrictions for Configuring External Ethernet Data Plane Loopback

Configuring External Ethernet Data Plane Loopback

Configuration Examples for Ethernet Data Plane Loopback

Verifying the Ethernet Data Plane Loopback Configuration

Troubleshooting the Ethernet Data Plane Loopback Configuration

CFM Support on Routed Port and Port MEP

Restrictions for Configuring Ethernet CFM

Configuring Ethernet CFM (Port MEP)

Configuration Example for Ethernet CFM (Port MEP)

Verifying the Ethernet CFM Configuration on a Port MEP

Configuring Ethernet CFM (Single-Tagged Packets)

Configuration Example for Ethernet CFM (Single-Tagged Packets)

Verifying the Ethernet CFM Configuration for Single-Tagged Packets

Configuring Ethernet CFM (Double-Tagged Packets)

Configuration Example for Ethernet CFM (Double-Tagged Packets)

Verififying the Ethernet CFM Configuration for Double-Tagged Packets

Troubleshooting Ethernet CFM Configuration

Support for Y.1731 Performance Monitoring on a Routed Port (L3 Subinterface)

Frame Delay

Restrictions for Configuring Two-Way Delay Measurement

Configuring Two-Way Delay Measurement

Configuration Examples for Two-Way Delay Measurement

Verifying Two-Way Delay Measurement Configuration

Troubleshooting Two-Way Delay Measurement Configuration


Configuring Ethernet CFM and Y.1731 Performance Monitoring on Layer 3 Interfaces


This chapter provides procedures for configuring the network interface device functionality, Ethernet data plane loopback, IEEE connectivity fault management, and Y.1731 performance monitoring, and contains the following sections:

Configuring a Network Interface Device on the L3 Interface

Ethernet Data Plane Loopback

CFM Support on Routed Port and Port MEP

Support for Y.1731 Performance Monitoring on a Routed Port (L3 Subinterface)

Configuring a Network Interface Device on the L3 Interface

Configuring a Network Interface Device (NID) enables support for the NID functionality on the router without including a NID hardware in the network. This feature combines the Customer-Premises Equipment (CPE) and the NID functionality into a physical device. The following are the advantages of configuring the NID functionality:

Eliminates a physical device.

Supports both the managed CPE feature set and the NID requirements.


Note This feature is supported only if you have purchased the DATA technology package functionality (datak9) licensing package. For more information about managing software activation licenses on the Cisco ISR and Cisco ISR G2 platforms, see http://www.cisco.com/en/US/docs/routers/access/sw_activation/SA_on_ISR.html.


Configuring the NID

The following steps describe how to configure the NID:

SUMMARY STEPS


Step 1 enable

Step 2 configure terminal

Step 3 interface gigabitethernet slot/port

Step 4 port-tagging

Step 5 encapsulation dot1q vlan-id

Step 6 set cos cos-value

Step 7 end

DETAILED STEPS

 
Command
Purpose

Step 1 

enable

Example:

Router>enable

Enables the privileged EXEC mode.

Enter your password when prompted.

Step 2 

configure terminal

Example:

Router#configure terminal

Enters the global configuration mode.

Step 3 

interface gigabitethernet slot/port

Example:

Router(config)#interface gigabitethernet 0/2

Specifies an interface and enters the interface configuration mode.

Step 4 

port-tagging

Example:

Router(config-if)#port-tagging

Inserts the VLAN ID into a packet header to identify which Virtual Local Area Network (VLAN) the packet belongs to.

Step 5 

encapsulation dot1q vlan-id

Example:

Router(config-if-port-tagging)#encaps ulation dot1q 10

Defines the encapsulation format as IEEE 802.1Q (dot1q), and specifies the VLAN identifier.

Step 6 

set cos cos-value

Example:

Router(config-if-port-tagging)#set cos 6

Sets the Layer 2 class of service (CoS) value to an outgoing packet end.

Step 7 

end

Example:

Router(config-if-port-tagging)#end

Exits the interface configuration mode.

Configuration Example

This configuration example shows how to configure the NID:

Router>enable
Router#configure terminal
Router(config)#interface gigabitethernet 0/2
Router(config-if)#port-tagging
Router(config-if-port-tagging)#encapsulation dot1q 10
Router(config-if-port-tagging)#set cos 6
Router(config-if-port-tagging)#end

Verifying the NID Configuration

Use the following commands to verify the port tagging sessions:

show run int

ping

Use the show run int command to display the port tagging sessions:

Router#show run int gi0/2
Building configuration...
Current configuration : 10585 bytes
!
interface GigabitEthernet0/2
 no ip address
 duplex auto
 speed auto
 port-tagging
  encapsulation dot1q 10
  set cos 6
  exit
end
!
interface GigabitEthernet0/2.1101
encapsulation dot1Q 100 
ip address 132.1.101.4 255.255.255.0
!
interface GigabitEthernet0/2.1102
encapsulation dot1Q 100
ip address 132.1.102.4 255.255.255.0
!
 
 

Use the ping command to verify the connectivity with port tagging configured:

Router#ping 132.1.101.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 132.1.101.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
router#

Troubleshooting the NID Configuration

Table 1 lists the debug commands to troubleshoot the issues pertaining to the NID functionality.

The Cisco IOS Master Command List at

http://www.cisco.com/en/US/docs/ios/mcl/allreleasemcl/all_book.html provides more information about these commands.


Caution Because debugging output is assigned high priority in the CPU process, it can diminish the performance of the router or even render it unusable. For this reason, use debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff.


Note Before you run any of the debug commands listed in the following table, ensure that you run the logging buffered debugging command, and then turn off console debug logging using the no logging console command.


Table 1 debug Commands for NID Configuration 

debug Command
Purpose

debug ethernet nid configuration

Enables debugging of configuration-related issues.

debug ethernet nid packet egress

Enables debugging of packet processing (VLAN tag push) on the egress side.

debug ethernet nid packet ingress

Enables debugging of packet processing (VLAN tag pop) on the ingress side.


Ethernet Data Plane Loopback

The Ethernet Data Plane Loopback feature provides a means for remotely testing the throughput of an Ethernet port. You can verify the maximum rate of frame transmission with no frame loss.


Note This feature is supported only if you have purchased the DATA technology package functionality (datak9) licensing package. For more information about managing software activation licenses on the Cisco ISR and Cisco ISR G2 platforms, see http://www.cisco.com/en/US/docs/routers/access/sw_activation/SA_on_ISR.html.



Note Internal Ethernet data plane loopback is not supported.


Restrictions for Configuring External Ethernet Data Plane Loopback

Follow the guidelines and take note of the restrictions listed here when configuring Ethernet data plane loopback on a Layer 3 interface:

Only external loopback (packets coming from the wire side) on the L3 dot1q subinterface and (untagged) main interface are supported.

To perform a MAC swap, the destination address and source address must be swapped for the packets that are looped back. If the destination address is broadcast or multicast, the MAC address is used as the source address for the packets that are looped back.

Loopback operations are supported at line rate.

Untagged frames are not supported on a subinterface. However, the frames for dot1q and qinq are supported on a subinterface.

dot1ad is not supported on the main interface. However, untagged frames are supported on the main interface.

Single VLAN is supported as a filtering option for a subinterface, but VLAN list and VLAN range are not supported.

Only MAC address is supported as a filtering option for the main interface.

For the filtering option, the destination MAC cannot be combined with inner VLAN or outer VLAN.

There is no support for L3 and L4 loopback. Source and destination IP address or source and destination ports will not be swapped.

Connectivity Fault Management (CFM) packets are transparent to the data plane loopback configuration and cannot be looped back.

Packets coming from the other side of the wire where loopback is configured and having the same destination MAC address are dropped.

The broadcast and multicast IP addresses of the broadcast and multicast IP frames that are received cannot be used as the source IP address of the frame when it is sent back to the initiator. In such a case, the IP address of the subinterface is used as the source IP address of the frame when it is sent back to the initiator.

Configuring External Ethernet Data Plane Loopback

Configuring external Ethernet data plane loopback is permitted on a Layer 3 main interface and subinterfaces.

Figure 1 represents a sample topology to configure Ethernet data plane loopback.

Figure 1

Sample Topology

The following steps show how to configure external Ethernet data plane loopback on a subinterface using single and double tagging. (The procedure to configure external Ethernet data plane loopback on the main interface is similar to this procedure.)

SUMMARY STEPS


Step 1 enable

Step 2 configure terminal

Step 3 interface gigabitethernet slot/port.sub-port

Step 4 encapsulation dot1q vlan-id

or

encapsulation dot1q vlan-id second-dot1q inner vlan-id

Step 5 ethernet loopback permit external

Step 6 end

DETAILED STEPS

 
Command
Purpose

Step 1 

enable

Example:

Router>enable

Enables the privileged EXEC mode.

Enter your password when prompted.

Step 2 

configure terminal

Example:

Router#configure terminal

Enters the global configuration mode.

Step 3 

interface gigabitethernet slot/port.sub-port

Example:

Router(config)#interface gigabitethernet 0/2.1101

Specifies the subnterface and enters the subinterface configuration mode.

Step 4 

encapsulation dot1q vlan-id

or

encapsulation dot1q vlan-id second-dot1q inner vlan-id

Example:

Router(config-subif)#encapsulation dot1q 100

or

Router(config-subif)#encapsulation dot1q 100 second-dot1q 1101

Defines the encapsulation format as IEEE 802.1Q (dot1q), and specifies the VLAN identifier.

For double tagging, use the second-dot1q keyword and the inner vlan-id argument to specify the VLAN tag.

Step 5 

ethernet loopback permit external

Example:

Router(config-subif)#ethernet loopback permit external

Configures Ethernet external loopback on the subinterface.

Step 6 

end

Example:

Router(config-subif)#end

Exits the subinterface configuration mode.

To start Ethernet data plane loopback, run the following command:

 
Command
Purpose

Step 1 

ethernet loopback start local interface gigabitethernet slot/port.sub-port external timeout none

Example:

Router#ethernet loopback start local interface gigabitethernet 0/2.1101 external timeout none

Starts Ethernet external loopback on a subinterface.

Enter timeout as none to have no time out period for the loopback.

To stop Ethernet data plane loopback, perform the following steps:

 
Command
Purpose

Step 1 

ethernet loopback stop local interface gigabitethernet slot/port.sub-port id session-id

Example:

Router#ethernet loopback stop local interface gigabitethernet 0/2.1101 id 1

Stops Ethernet external loopback on a subinterface.

Enter the value of the loopback session ID to specify the loopback session that you want to stop.

Step 2 

show ethernet loopback active

Example:

Router#show ethernet loopback active

Displays information to verify if the loopback session has ended.

Configuration Examples for Ethernet Data Plane Loopback

This example shows how to configure Ethernet data plane loopback using single tagging:

Router>enable
Router#configure terminal
Router(config)#interface gigabitethernet 0/2.1101
Router(config-subif)#encapsulation dot1q 100
Router(config-subif)#ethernet loopback permit external
Router(config-subif)#end

This example shows how to configure Ethernet data plane loopback using double tagging:

Router>enable
Router#configure terminal
Router(config)#interface gigabitethernet 0/2.1101
Router(config-subif)#encapsulation dot1q 100 second-dot1q 1101
Router(config-subif)#ethernet loopback permit external
Router(config-subif)#end

This example shows how to start an Ethernet data plane loopback:

Router#ethernet loopback start local interface gigabitethernet 0/2.1101 external timeout 
none
This is an intrusive loopback and the packets matched with the service will not be able to 
pass through. Continue? (yes/[no]):
Enter yes to continue.
 
 

This example shows how to stop an Ethernet data plane loopback:

Router#ethernet loopback stop local interface gigabitethernet 0/2.1101 id 1
Router#*Oct 21 10:16:17.887: %E_DLB-6-DATAPLANE_LOOPBACK_STOP: Ethernet Dataplane Loopback 
Stop on interface GigabitEthernet0/2 with session id 1
Router#show ethernet loopback active
Total Active Session(s): 0
Total Internal Session(s): 0
Total External Session(s): 0

Verifying the Ethernet Data Plane Loopback Configuration

Use the following commands to verify the Ethernet data plane loopback configuration:

show ethernet loopback permitted

show ethernet loopback active

 
 

Use the show ethernet loopback permitted command to view the loopback capabilities per interface:

Router#show ethernet loopback permitted
--------------------------------------------------------------------------------
Interface                               SrvcInst Direction            
Dot1q/Dot1ad(s)                         Second-Dot1q(s)
--------------------------------------------------------------------------------
Gi0/2.1101                              N/A      External 
100                                     1101                                   
 
 

Use the show ethernet loopback active command to display the summary of the active loopback sessions on a subinterface:

Router#show ethernet loopback active
Loopback Session ID     : 1
Interface               : GigabitEthernet0/2.1101
Service Instance        : N/A
Direction               : External
Time out(sec)           : none
Status                  : on
Start time              : *10:17:46.930 UTC Mon Oct 21 2013
Time left               : N/A
Dot1q/Dot1ad(s)         : 100
Second-dot1q(s)         : 1101
Source Mac Address      : Any
Destination Mac Address : Any
Ether Type              : Any
Class of service        : Any
Llc-oui                 : Any
 
 
 
 
Total Active Session(s): 1
Total Internal Session(s): 0
Total External Session(s): 1
 
 

Use the show ethernet loopback active command to display the summary of the active loopback sessions on the main interface:

Router#show ethernet loopback permitted
Loopback Session ID     : 1
Interface               : GigabitEthernet0/2
Service Instance        : N/A
Direction               : External
Time out(sec)           : none
Status                  : on
Start time              : *10:14:23.507 UTC Mon Oct 21 2013
Time left               : N/A
Dot1q/Dot1ad(s)         : 1-100
Second-dot1q(s)         : 1-1101
Source Mac Address      : Any
Destination Mac Address : Any
Ether Type              : Any
Class of service        : Any
Llc-oui                 : Any
 
 
 
 
Total Active Session(s): 1
Total Internal Session(s): 0
Total External Session(s): 1

Troubleshooting the Ethernet Data Plane Loopback Configuration

Table 2 lists the debug commands to troubleshoot issues pertaining to the Ethernet Data Plane Loopback feature.

The Cisco IOS Master Command List at

http://www.cisco.com/en/US/docs/ios/mcl/allreleasemcl/all_book.html provides more information about these commands.


Caution Because debugging output is assigned high priority in the CPU process, it can diminish the performance of the router or even render it unusable. For this reason, use debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff.


Note Before you run any of the debug commands listed in the following table, ensure that you run the logging buffered debugging command, and then turn off console debug logging using the no logging console command.


Table 2 debug Commands for Ethernet Data Plane Loopback Configuration 

debug Command
Purpose

debug elb-pal-pd all

Displays all the debugging information about the Ethernet data plane loopback configuration.

debug elb-pal-pd error

Displays debugging information about Ethernet data plane loopback configuration errors.

debug elb-pal-pd event

Displays debugging information about Ethernet data plane loopback configuration changes.


CFM Support on Routed Port and Port MEP

IEEE Connectivity Fault Management (CFM) is an end-to-end per-service Ethernet-layer Operations, Administration, and Maintenance (OAM) protocol. CFM includes proactive connectivity monitoring, fault verification, and fault isolation for large Ethernet metropolitan-area networks (MANs) and WANs.


Note This feature is supported only if you have purchased the DATA technology package functionality (datak9) licensing package. For more information about managing software activation licenses on the Cisco ISR and Cisco ISR G2 platforms, see http://www.cisco.com/en/US/docs/routers/access/sw_activation/SA_on_ISR.html.


Restrictions for Configuring Ethernet CFM

A specific domain must be configured. If it is not, an error message is displayed.

Multiple domains (different domain names) having the same maintenance level can be configured. However, associating a single domain name with multiple maintenance levels is not permitted.

Configuring Ethernet CFM (Port MEP)

Complete these steps to configure and enable Ethernet CFM on a port Maintenance End Point (MEP):

SUMMARY STEPS


Step 1 enable

Step 2 configure terminal

Step 3 ethernet cfm ieee

Step 4 ethernet cfm global

Step 5 ethernet cfm domain domain-name level value

Step 6 service service-name port

Step 7 continuity-check interval value

Step 8 end

Step 9 configure terminal

Step 10 interface gigabitethernet slot/port

Step 11 ethernet cfm mep domain domain-name mpid mpid-value service service-name

Step 12 end

DETAILED STEPS

 
Command
Purpose

Step 1 

enable

Example:

Router>enable

Enables the privileged EXEC mode.

Enter your password when prompted.

Step 2 

configure terminal

Example:

Router#configure terminal

Enters the global configuration mode.

Step 3 

ethernet cfm ieee

Example:

Router(config)#ethernet cfm ieee

Enables the IEEE version of CFM.

Step 4 

ethernet cfm global

Example:

Router(config)#ethernet cfm global

Enables CFM processing globally on the router.

Step 5 

ethernet cfm domain domain-name level value

Example:

Router(config-ecfm)#ethernet cfm domain carrier level 2

Defines a CFM maintenance domain at a specified level, and enters the Ethernet CFM configuration mode.

level can be any value from 0 to 7.

Step 6 

service service-name port

Example:

Router(config-ecfm)#service carrier port

Creates a service on the interface and sets the config-ecfm-srv submode.

Step 7 

continuity-check interval value

Example:

Router(config-ecfm-srv)#continuity-ch eck interval 100m

Enables sending continuity check messages at the set interval.

Step 8 

end

Example:

Router(config-ecfm-srv)#end

Returns the router to the privileged EXEC mode.

Step 9 

configure terminal

Example:

Router#configure terminal

Enters the global configuration mode.

Step 10 

interface gigabitethernet slot/port

Example:

Router(config)#interface gigabitethernet 0/2

Specifies an interface and enters the interface configuration mode.

Step 11 

ethernet cfm mep domain domain-name mpid mpid-value service service-name

Example:

Router(config-if)#ethernet cfm mep domain carrier mpid 44 service carrier

Sets a port to a maintenance domain and defines it as an MEP.

Note The values for domain and service must be the same as the values configured for CFM.

Step 12 

end

Example:

Router(config-if-ecfm-mep)#end

Returns the router to the privileged EXEC mode.

Configuration Example for Ethernet CFM (Port MEP)

This example shows how to configure Ethernet CFM on a port MEP:

Router>enable
Router#configure terminal
Router(config)#ethernet cfm ieee
Router(config)#ethernet cfm global
Router(config-ecfm)#ethernet cfm domain carrier level 2
Router(config-ecfm)#service carrier port
Router(config-ecfm-srv)#continuity-check interval 100m
Router(config-ecfm-srv)#end
Router#configure terminal
Router(config)#interface gigabitethernet 0/2
Router(config-if)#ethernet cfm mep domain carrier mpid 44 service carrier
Router(config-if-ecfm-mep)#end

Verifying the Ethernet CFM Configuration on a Port MEP

Use the following commands to verify Ethernet CFM configured on a port MEP:

show ethernet cfm domain

show ethernet cfm maintenance-points local

show ethernet cfm maintenance-points remote

ping ethernet mpid mpid-value domain domain-name service service-name cos value

traceroute ethernet mpid mpid-value domain domain-name service service-name

show ethernet cfm error configuration

 
 

Use the show ethernet cfm domain command to view details about CFM maintenance domains:

Router#show ethernet cfm domain carrier
Domain Name: carrier
Level: 2 
Total Services: 1
  Services:
  Type Id   Dir CC CC-int Static-rmep Crosscheck MaxMEP Source  MA-Name 
  Port none Dwn Y  100ms  Disabled    Disabled   100    Static  carrier
Router#
 
 

Use the show ethernet cfm maintenance-points local command to view the MEPs that are configured locally on a router. The following is a sample output of the show ethernet cfm maintenance-points local command:

Router#show ethernet cfm maintenance-points local 
Local MEPs:
--------------------------------------------------------------------------------
MPID Domain Name                                 Lvl   MacAddress     Type  CC  
Ofld Domain Id                                   Dir   Port           Id        
     MA Name                                           SrvcInst       Source    
     EVC name                                                                   
--------------------------------------------------------------------------------
44   carrier                                     2     5657.a844.04fa Port  Y
No   carrier                                     Down  Gi0/2          none 
     carrier                                           N/A            Static 
     N/A                                                                        
 
 
 
 
Total Local MEPs: 1
 
 
Local MIPs: None
 
 

Use the show ethernet cfm maintenance-points remote command to display information about remote maintenance point domains or levels. In the following example, carrier, Provider, and customer are the maintenance point domains that are configured.

 
 
On router 1:
 
 
Router1#show ethernet cfm maintenance-points remote 
--------------------------------------------------------------------------------
MPID  Domain Name                                 MacAddress          IfSt  PtSt
 Lvl  Domain ID                                   Ingress                       
 RDI  MA Name                                     Type Id             SrvcInst  
      EVC Name                                                        Age       
      Local MEP Info                                                            
--------------------------------------------------------------------------------
43    carrier                                     5657.a86c.fa92      Up    N/A 
 2    carrier                                     Gi0/2                         
 -    carrier                                     Port none           N/A       
      N/A                                                             0s
      MPID: 44 Domain: carrier MA: carrier
33    Provider                                    5657.a86c.fa92      Up    Up  
 5    Provider                                    Gi0/2.100                     
 -    Provider                                    Vlan 100            N/A       
      N/A                                                             0s
      MPID: 34 Domain: Provider MA: Provider
3101  customer                                    5657.a86c.fa92      Up    Up  
 7    customer                                    Gi0/2.1101                    
 -    customer1101                                S,C  100,1101       N/A       
      N/A                                                             0s
      MPID: 4101 Domain: customer MA: customer1101
3102  customer                                    5657.a86c.fa92      Up    Up  
 7    customer                                    Gi0/2.1102                    
 -    customer1102                                S,C  100,1102       N/A       
      N/A                                                             0s
      MPID: 4102 Domain: customer MA: customer1102
 
 
Total Remote MEPs: 4
 
 

Use the show ethernet cfm maintenance-points remote command to view the details of a remote maintenance point domain:

 
 
On router 1:
 
 
Router1#show ethernet cfm maintenance-points remote domain carrier service carrier
--------------------------------------------------------------------------------
MPID  Domain Name                                 MacAddress          IfSt  PtSt
 Lvl  Domain ID                                   Ingress                       
 RDI  MA Name                                     Type Id             SrvcInst  
      EVC Name                                                        Age       
      Local MEP Info                                                            
--------------------------------------------------------------------------------
43    carrier                                     5657.a86c.fa92      Up    Up  
 2    carrier                                     Gi0/2                    
 -    carrier                                     S,C  100,1101       N/A       
      N/A                                                             0s
      MPID: 44 Domain: carrier MA: carrier
Total Remote MEPs: 1

On router 2:

Router2#show ethernet cfm maintenance-points remote domain carrier service carrier
--------------------------------------------------------------------------------
MPID  Domain Name                                 MacAddress          IfSt  PtSt
 Lvl  Domain ID                                   Ingress                       
 RDI  MA Name                                     Type Id             SrvcInst  
      EVC Name                                                        Age       
      Local MEP Info                                                            
--------------------------------------------------------------------------------
44    carrier                                     5657.g945.04fa      Up    Up  
 2    carrier                                     Gi0/2                    
 -    carrier                                     S,C  100,1101       N/A       
      N/A                                                             0s
      MPID: 43 Domain: carrier MA: carrier

Use the ping command to verify if Loopback Messages (LBM) and Loopback Replies (LBR) are successfully sent and received between the routers:

Router1#ping ethernet mpid 44 domain carrier service carrier cos 5          
Type escape sequence to abort.
Sending 5 Ethernet CFM loopback messages to 5657.a86c.fa92, timeout is 5 seconds:!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
Router1#

Use the traceroute command to send the Ethernet CFM traceroute messages:

Router#traceroute ethernet mpid 44 domain carrier service carrier
Type escape sequence to abort. TTL 64. Linktrace Timeout is 5 seconds
Tracing the route to 5657.a86c.fa92 on Domain carrier, Level 2, service carrier
Traceroute sent via Gi0/2
 
 
B = Intermediary Bridge
! = Target Destination
* = Per hop Timeout
--------------------------------------------------------------------------------
                             MAC      Ingress        Ingr Action  Relay Action  
  Hops   Host             Forwarded   Egress         Egr Action   Previous Hop  
--------------------------------------------------------------------------------
! 1                    5657.a86c.fa92 Gi0/2          IngOk        RlyHit:MEP    
                       Not Forwarded                              5657.g945.04fa
Router#

Configuring Ethernet CFM (Single-Tagged Packets)

Complete these steps to configure and enable Ethernet CFM for single-tagged packets:

SUMMARY STEPS


Step 1 enable

Step 2 configure terminal

Step 3 ethernet cfm ieee

Step 4 ethernet cfm global

Step 5 ethernet cfm domain domain-name level level-id

Step 6 service service-name vlan vlan-id direction down

Step 7 continuity-check

Step 8 interface gigabitethernet slot/port

Step 9 ethernet cfm mep domain domain-name mpid value service service-name

Step 10 interface gigabitethernet slot/port.subinterface

Step 11 encapsulation dot1q vlan-id

Step 12 end

DETAILED STEPS

 
Command
Purpose

Step 1 

enable

Example:

Router>enable

Enables the privileged EXEC mode.

Enter your password when prompted.

Step 2 

configure terminal

Example:

Router#configure terminal

Enters the global configuration mode.

Step 3 

ethernet cfm ieee

Example:

Router(config)#ethernet cfm ieee

Enables the IEEE version of CFM.

Step 4 

ethernet cfm global

Example:

Router(config)#ethernet cfm global

Enables CFM processing globally on the router.

Step 5 

ethernet cfm domain domain-name level value

Example:

Router(config)#ethernet cfm domain customer level 7

Defines a CFM maintenance domain at a specified level, and enters the Ethernet CFM configuration mode.

level can be any value from 0 to 7.

Step 6 

service service-name vlan vlan-id direction down

Example:

Router(config-ecfm)#service customer1101 vlan 100 direction down

Enters the CFM service configuration mode.

vlan—Specifies the VLAN.

Step 7 

continuity-check

Example:

Router(config-ecfm-srv)#continuity-ch eck

Enables sending continuity check messages.

Step 8 

interface gigabitethernet slot/port

Example:

Router(config-ecfm-srv)#interface gigabitethernet 0/2

Specifies an interface and enters the interface configuration mode.

Step 9 

ethernet cfm mep domain domain-name mpid mpid-value service service-name

Example:

Router(config-if)#ethernet cfm mep domain customer mpid 100 service customer1101

Sets a port to a maintenance domain and defines it as an MEP.

Note The values for domain and service must be the same as the values that were configured for CFM.

Step 10 

interface gigabitethernet slot/port.subinterface

Example:

Router(config-if-ecfm-mep)#interface gigabitethernet 0/2.1

Specifies a subinterface and enters the subinterface configuration mode.

Step 11 

encapsulation dot1q vlan-id

Example:

Router(config-subif)#encapsulation dot1q 100

Defines the encapsulation format as IEEE 802.1Q (dot1q), and specifies the VLAN identifier.

Step 12 

end

Example:

Router(config-subif)#end

Returns the router to the privileged EXEC mode.

Configuration Example for Ethernet CFM (Single-Tagged Packets)

This example shows how to configure Ethernet CFM for single-tagged packets:

Router>enable
Router#configure terminal
Router(config)#ethernet cfm ieee
Router(config)#ethernet cfm global
Router(config)#ethernet cfm domain customer level 7
Router(config-ecfm)#service customer1101 vlan 100 direction down
Router(config-ecfm-srv)#continuity-check
Router(config)#interface gigabitethernet 0/2
Router(config-if)#ethernet cfm mep domain customer mpid 100 service customer1101
Router(config-if-ecfm-mep)#interface gigabitethernet 0/2.1
Router(config-subif)#encapsulation dot1q 100
Router(config-subif)#end

Verifying the Ethernet CFM Configuration for Single-Tagged Packets

Use the following commands to verify Ethernet CFM configured for single-tagged packets:

show ethernet cfm domain

show ethernet cfm maintenance-points local

show ethernet cfm maintenance-points remote

show ethernet cfm error configuration

Use the show ethernet cfm domain command to display the maintenance point domains configured in the network. In the following example, customer, enterprise, and carrier maintenance point domains are configured:

Router#show ethernet cfm domain
Domain Name: customer
Level: 7
Total Services: 1
  Services:
  Type Id   Dir CC CC-int Static-rmep Crosscheck MaxMEP Source  MA-Name
  Vlan 100  Dwn Y  10s    Disabled    Disabled   100    Static  customer1101
 
 
Domain Name: enterprise
Level: 6
Total Services: 1
  Services:
  Type Id   Dir CC CC-int Static-rmep Crosscheck MaxMEP Source  MA-Name
  Vlan 110  Dwn Y  10s    Disabled    Disabled   100    Static  custservice
 
 
Domain Name: carrier
Level: 2
Total Services: 1
  Services:
  Type Id   Dir CC CC-int Static-rmep Crosscheck MaxMEP Source  MA-Name
  Vlan 200  Dwn Y  10s    Disabled    Disabled   100    Static  carrier
Router#

Use the show ethernet cfm maintenance-points local command to view the local MEPs. The following is a sample output of the show ethernet cfm maintenance-points local command:

Router#show ethernet cfm maintenance-points local
--------------------------------------------------------------------------------
MPID Domain Name                                 Lvl   MacAddress     Type  CC
Ofld Domain Id                                   Dir   Port           Id
     MA Name                                           SrvcInst       Source
     EVC name
--------------------------------------------------------------------------------
100  customer                                    7     70ca.9b4d.a400 Vlan  Y
No   customer                                    Down  Gi0/2          100
     customer1101                                      N/A            Static
     N/A
400  enterprise                                  6     70ca.9b4d.a400 Vlan  I
No   enterprise                                  Down  Gi0/1          110
     custservice                                       N/A            Static
     N/A
44   carrier                                     2     70ca.9b4d.a400 Vlan  N
No   carrier                                     Down  Gi0/2          200
     carrier                                           N/A            Static
     N/A
 
 
Total Local MEPs: 3
 
 
Local MIPs: None
Router#
 
 

Use the show ethernet cfm maintenance-points remote command to display information about remote maintenance point domains or levels.

The following example displays the continuity check messages exchanged between remote MEPs:
 
 
On router 1:
 
 
Router1#show ethernet cfm maintenance-points remote
-----------------------------------------------------------------------------------------
MPID Domain Name             MacAddress           IfSt               PtSt
 Lvl Domain                  Ingress
 RDI MA                      Type Id              SrvcInst
     EVC Name                                     Age
     Local MEP Info
-----------------------------------------------------------------------------------------
110  customer                70ca.9b4d.a400       Up                  Up
 7   customer                Gi0/2
 -   customer1101            Vlan 100             N/A
     N/A                                          12s
     MPID: 100 Domain: customer MA: customer1101
 
 
410  enterprise              70ca.9b4d.a400       Up                  Up
 6   enterprise              Gi0/1
 -   custservice             Vlan 110             N/A
     N/A                                          12s
     MPID: 400 Domain: enterprise MA: custservice
 
 
43   carrier                 70ca.9b4d.a400       Up                  Up
 2   carrier                 Gi0/2
 -   carrier                 Vlan 200             N/A
     N/A                                          12s
     MPID: 44  Domain: carrier MA: carrier
 
 
Total Remote MEPs: 3
Router1#
 
 

On router 2:

Router2#show ethernet cfm maintenance-points remote
-----------------------------------------------------------------------------------------
MPID Domain Name             MacAddress           IfSt               PtSt
 Lvl Domain                  Ingress
 RDI MA                      Type Id              SrvcInst
     EVC Name                                     Age
     Local MEP Info
-----------------------------------------------------------------------------------------
100  customer                0026.99f7.0b41       Up                  Up
 7   customer                Gi0/2
 -   customer1101            Vlan 100             N/A
     N/A                                          2s
     MPID: 110 Domain: customer MA: customer1101
 
 
400  enterprise              0026.99f7.0b41       Up                  Up
 6   enterprise              Gi0/1
 -   custservice             Vlan 110             N/A
     N/A                                          2s
     MPID: 410 Domain: enterprise MA: custservice
 
 
44   carrier                 0026.99f7.0b41       Up                  Up
 2   carrier                 Gi0/2
 -   carrier                 Vlan 200             N/A
     N/A                                          2s
     MPID: 43  Domain: carrier MA: carrier
 
 
Total Remote MEPs: 3
Router2#
 
 

Use the show ethernet cfm error configuration command to view Ethernet CFM configuration errors (if any). The following is a sample output of the show ethernet cfm error configuration command:

Router#show ethernet cfm error configuration
--------------------------------------------------------------------------------
CFM Interface      Type  Id       Level    Error type
--------------------------------------------------------------------------------
Gi0/2              S,C   100      5        CFMLeak

Configuring Ethernet CFM (Double-Tagged Packets)

Complete these steps to configure and enable Ethernet CFM for double-tagged packets:

SUMMARY STEPS


Step 1 enable

Step 2 configure terminal

Step 3 ethernet cfm ieee

Step 4 ethernet cfm global

Step 5 ethernet cfm domain domain-name level value

Step 6 service service-name vlan vlan-id inner-vlan inner-vlan-id direction down

Step 7 continuity-check

Step 8 interface gigabitethernet slot/port

Step 9 ethernet cfm mep domain domain-name mpid mpid-value service service-name

Step 10 interface gigabitethernet slot/port.subinterface

Step 11 encapsulation dot1q vlan-id second-dot1q inner vlan-id

Step 12 end

DETAILED STEPS

 
Command
Purpose

Step 1 

enable

Example:

Router>enable

Enables the privileged EXEC mode.

Enter your password when prompted.

Step 2 

configure terminal

Example:

Router#configure terminal

Enters the global configuration mode.

Step 3 

ethernet cfm ieee

Example:

Router(config)#ethernet cfm ieee

Enables the IEEE version of CFM.

Step 4 

ethernet cfm global

Example:

Router(config)#ethernet cfm global

Enables CFM processing globally on the router.

Step 5 

ethernet cfm domain domain-name level 0 to 7

Example:

Router(config-ecfm)#ethernet cfm domain customer level 7

Defines a CFM maintenance domain at a specified level, and enters Ethernet CFM configuration mode.

level can be any value from 0 to 7.

Step 6 

service service-name vlan vlan-id inner-vlan inner vlan-id direction down

Example:

Router(config-ecfm)#service customer1101 vlan 100 inner-vlan 30 direction down

Enters the CFM service configuration mode.

The following are the parameters:

vlan—Specifies the VLAN.

inner-vlan—The inner-vlan keyword and the inner vlan-id argument specify the VLAN tag for double-tagged packets.

Step 7 

continuity-check

Example:

Router(config-ecfm-srv)#continuity-ch eck

Enables sending continuity check messages.

Step 8 

interface gigabitethernet slot/port

Example:

Router(config-ecfm-srv)#interface gigabitethernet 0/2

Specifies an interface and enters the interface configuration mode.

Step 9 

ethernet cfm mep domain domain-name mpid mpid-value service service-name

Example:

Router(config-if)#ethernet cfm mep domain customer mpid 100 service customer1101

Sets a port to a maintenance domain and defines it as an MEP.

Note The values for domain and service must be the same as the values configured for CFM.

MPID—Specifies the maintenance endpoint identifier.

Step 10 

interface gigabitethernet slot/port.subinterface

Example:

Router(config-if-ecfm-mep)#interface gigabitethernet 0/2.1101

Specifies a subinterface and enters the subinterface configuration mode.

Step 11 

encapsulation dot1q vlan-id second-dot1q inner vlan-id

Example:

Router(config-subif)#encapsulation dot1q 100 second-dot1q 30

Defines the encapsulation format as IEEE 802.1Q (dot1q), and specifies the VLAN identifier.

Use the second-dot1q keyword and the inner vlan-id argument to specify the VLAN tag.

Step 12 

end

Example:

Router(config-subif)#end

Returns the router to the privileged EXEC mode.

Configuration Example for Ethernet CFM (Double-Tagged Packets)

This example shows how to configure Ethernet CFM for double-tagged packets:

Router>enable
Router#configure terminal
Router(config)#ethernet cfm ieee
Router(config)#ethernet cfm global
Router(config-ecfm)#ethernet cfm domain customer level 7
Router(config-ecfm)#service customer1101 vlan 100 inner-vlan 30 direction down
Router(config-ecfm-srv)#continuity-check
Router(config-ecfm-srv)#interface gigabitethernet 0/2
Router(config-if)#ethernet cfm mep domain customer mpid 100 service customer1101
Router(config-if-ecfm-mep)#interface gigabitethernet 0/2.1101
Router(config-subif)#encapsulation dot1q 100 second-dot1q 30
Router(config-subif)#end

Verififying the Ethernet CFM Configuration for Double-Tagged Packets

Use the following commands to verify Ethernet CFM configured for double-tagged packets:

show ethernet cfm maintenance-points local

show ethernet cfm maintenance-points remote

ping ethernet mpid mpid-value domain domain-name service service-name cos value

traceroute ethernet mpid mpid-value domain domain-name service service-name

show ethernet cfm error configuration

Use the show ethernet cfm maintenance-points local command to view the local MEPs. The following is a sample output of the show ethernet cfm maintenance-points local command:

Router#show ethernet cfm maintenance-points local
----------------------------------------------------------------------------------
MPID Domain Name          MacAddress                 IfSt                   PtSt
 Lvl Domain ID	          Ingress
 RDI MA Name              Type Id                    SrvcInst
     EVC Name                              Age
     Local MEP Info	
----------------------------------------------------------------------------------
100  customer             8843.e154.6f01             Up                     Up
 7   customer             Gi0/2.1101
 -   customer1101         S, C 100, 30               N/A
     N/A                                   58s
     MPID: 100 Domain: customer MA: customer1101
Router#

Use the show ethernet cfm maintenance-points remote command to display the remote maintenance point domains. In the following example, customer, carrier, and enterprise are the maintenance point domains that are configured:

On router 1:

 
 
Router1#show ethernet cfm maintenance-points remote
----------------------------------------------------------------------------------
MPID Domain Name          MacAddress                 IfSt                   PtSt
 Lvl Domain ID	          Ingress
 RDI MA Name              Type Id                    SrvcInst
     EVC Name                                        Age
     Local MEP Info	
----------------------------------------------------------------------------------
110  customer             8843.e154.6f01             Up                     Up
 7   customer             Gi0/2.1101
 -   customer1101         S, C 100, 30               N/A
     N/A                                             58s
     MPID: 100 Domain: customer MA: customer1101
 
 
43   carrier             8843.e154.6f01              Up                     Up
 2   carrier             Gi0/2.2
 -   carrier             S, C 50, 20                 N/A
     N/A                                             58s
     MPID: 44 Domain: carrier MA: carrier
 
 
410  enterprise          8843.e154.6f01              Up                     Up
 6   enterprise          Gi0/1.1
 -   custservice         S, C 200, 70                N/A
     N/A                                             58s
     MPID: 400 Domain: enterprise MA: custservice
 
 
Router1#
 
 

On router 2:

 
 
Router2#show ethernet cfm maintenance-points remote
----------------------------------------------------------------------------------
MPID Domain Name          MacAddress                 IfSt                   PtSt
 Lvl Domain ID	          Ingress
 RDI MA Name              Type Id                    SrvcInst
     EVC Name                                        Age
     Local MEP Info	
----------------------------------------------------------------------------------
100  customer             0026.99f7.0b41             Up                     Up
 7   customer             Gi0/2.1101
 -   customer1101         S, C 100, 30               N/A
     N/A                                             40s
     MPID: 110 Domain: customer MA: customer1101
 
 
44   carrier             0026.99f7.0b41              Up                     Up
 2   carrier             Gi0/2.2
 -   carrier             S, C 50, 20                 N/A
     N/A                                             40s
     MPID: 43 Domain: carrier MA: carrier
 
 
400  enterprise          0026.99f7.0b41              Up                     Up
 6   enterprise          Gi0/1.1
 -   custservice         S, C 200, 70                N/A
     N/A                                             40s
     MPID: 410 Domain: enterprise MA: custservice
 
 
Router2#
 
 

Use the ping command to verify if Ethernet CFM loopback messages are successfully sent and received between the routers:

Router#ping ethernet mpid 100 domain customer service customer1101  cos 5          
Type escape sequence to abort.
Sending 5 Ethernet CFM loopback messages to 8843.e154.6f01, timeout is 5 seconds:!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
Router#
 
 

Use the traceroute command to send the Ethernet CFM traceroute messages:

Router#traceroute ethernet mpid 100 domain customer service customer1101
Type escape sequence to abort. TTL 64. Linktrace Timeout is 5 seconds
Tracing the route to 8843.e154.6f01 on Domain customer, Level 7, service customer1101, 
vlan 100 inner-vlan 30
Traceroute sent via Gi0/2.1101
 
 
B = Intermediary Bridge
! = Target Destination
* = Per hop Timeout

--------------------------------------------------------------------------------

                             MAC      Ingress        Ingr Action  Relay Action  
  Hops   Host             Forwarded   Egress         Egr Action   Previous Hop  
--------------------------------------------------------------------------------
! 1                    8843.e154.6f01 Gi0/2.1101 IngOk        RlyHit:MEP    
                       Not Forwarded                              5657.a86c.fa92
 
 

Use the show ethernet cfm error configuration command to view Ethernet CFM configuration errors (if any). The following is a sample output of the show ethernet cfm error configuration command:

Router#show ethernet cfm error configuration
--------------------------------------------------------------------------------
CFM Interface      Type  Id         Level    Error type
--------------------------------------------------------------------------------
Gi0/2              S,C   100,30     5        CFMLeak
Gi0/2              S,C   100,30     1        CFMLeak

Troubleshooting Ethernet CFM Configuration

Table 3 lists the debug commands to troubleshoot issues pertaining to the Ethernet CFM configuration.

The Cisco IOS Master Command List at

http://www.cisco.com/en/US/docs/ios/mcl/allreleasemcl/all_book.html provides more information about these commands.


Caution Because debugging output is assigned high priority in the CPU process, it can diminish the performance of the router or even render it unusable. For this reason, use debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff.


Note Before you run any of the debug commands listed in the following table, ensure that you run the logging buffered debugging command, and then turn off console debug logging using the no logging console command.


Table 3 debug Commands for Ethernet CFM Configuration 

debug Command
Purpose

debug ethernet cfm all

Enables all Ethernet CFM debug messages.

debug ethernet cfm diagnostic

Enables low-level diagnostic debugging of Ethernet CFM general events or packet-related events.

debug ethernet cfm error

Enables debugging of Ethernet CFM errors.

debug ethernet cfm packets

Enables debugging of Ethernet CFM message packets.

debug ecfmpal all

Enables debug messages for all Ethernet CFM platform events.

debug ecfmpal api

Displays debug messages for all Ethernet CFM platform API events.

debug ecfmpal common

Displays debug messages for all Ethernet CFM platform common events.

debug ecfmpal ecfmpal

Enables debugging of all Ethernet CFM platform events.

debug ecfmpal epl

Enables debugging of all Ethernet CFM platform endpoint list (EPL) events.

debug ecfmpal isr

Enables debugging of all Ethernet CFM platform interrupt service request (ISR) events.


Support for Y.1731 Performance Monitoring on a Routed Port (L3 Subinterface)

Y.1731 Performance Monitoring (PM) provides a standard Ethernet PM function that includes measurement of Ethernet frame delay, frame delay variation, frame loss, and frame throughput measurements specified by the ITU-T Y-1731 standard and interpreted by the Metro Ethernet Forum (MEF) standards group.


Note This feature is supported only if you have purchased the DATA technology package functionality (datak9) licensing package. For more information about managing software activation licenses on the Cisco ISR and Cisco ISR G2 platforms, see http://www.cisco.com/en/US/docs/routers/access/sw_activation/SA_on_ISR.html.


Frame Delay

Ethernet frame delay measurement is used to measure frame delay and frame delay variations. Ethernet frame delay is measured using the Delay Measurement Message (DMM) method.

Restrictions for Configuring Two-Way Delay Measurement

Follow the guidelines and restrictions listed here when you configure two-way delay measurement:

Y.1731 PM measurement works only for a point-to-point network topology.

The granularity of the clock for delay measurement is in seconds and nanoseconds.

CFM Y.1731 packets work with a maximum of two VLAN tags. The expected behavior is not observed with more VLAN tags. Also, CFM Y.1731 packets do not work with untagged cases.

Configuring Two-Way Delay Measurement

The following steps show how to configure two-way delay measurement. Both single and double tagging methods are included in the steps listed below.

SUMMARY STEPS


Step 1 enable

Step 2 configure terminal

Step 3 ip sla operation number

Step 4 ethernet y1731 delay DMM domain value vlan vlan-id mpid value cos value source mpid value

or

ethernet y1731 delay DMM domain value vlan vlan-id inner-vlan inner vlan-id mpid value cos value source mpid value

Step 5 aggregate interval seconds

Step 6 exit

Step 7 ip sla schedule operation number start-time {start time | now}

Step 8 end

DETAILED STEPS

 
Command
Purpose

Step 1 

enable

Example:

Router> enable

Enables the privileged EXEC mode.

Enter your password when prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters the global configuration mode.

Step 3 

ip sla operation number

Example:

Router(config)# ip sla 1101

Enables the IP SLA configuration.

operation-number—The IP SLA operation you want to configure.

Step 4 

ethernet y1731 delay DMM domain value vlan vlan-id mpid value cos value source mpid value

or

ethernet y1731 delay DMM domain value vlan vlan-id inner-vlan inner vlan-id mpid value cos value source mpid value

Example:

Router(config-ip-sla)# ethernet y1731 delay DMM domain customer vlan 100 mpid 3101 cos 1 source mpid 4101

or

Router(config-ip-sla)# ethernet y1731 delay DMM domain customer vlan 100 inner-vlan 1101 mpid 3101 cos 1 source mpid 4101

Configures a two-way delay measurement.

Note Both single tagging and double tagging are supported.

The following are the parameters:

delay—Specifies the delay distribution parameter.


Note DMM is the only supported delay distribution parameter.


vlan—Specifies the VLAN.

inner-vlan—The inner-vlan keyword and the inner vlan-id argument specify the VLAN tag for double-tagged packets.

cos—Specifies the CoS. The value can be any number between 0 and 7.


Note For double-tagged packets, the cos value corresponds to the value specified for the outer tag.


mpid—Specifies the destination MPID.

source—Specifies the source MPID.

Step 5 

aggregate interval seconds

Example:

Router(config-sla-y1731-delay)# aggregate interval 30

Configures the Y.1731 aggregation parameter, where aggregate interval refers to the interval at which the packets are sent.

seconds—Specifies the length of time, in seconds.

Step 6 

exit

Example:

Router(config-sla-y1731-delay)# exit

Exits the router configuration mode.

Step 7 

ip sla schedule operation number life {value | forever} start-time value

Example:

Router(config)#ip sla schedule 1101 life forever start-time now

Schedules the two-way delay measurement.

life—Specifies a period of time (in seconds) to execute. The value can also be set as forever.

start-time—Specifies the time at which to start the entry. The options available are after, hh:mm, hh:mm:ss, now, and pending.

Step 8 

end

Example:

Router(config)#end

Exits the router configuration mode and returns to the privileged EXEC mode.

Configuration Examples for Two-Way Delay Measurement

This example shows how to configure two-way delay measurement using single tagging:

router>enable
router#configure terminal
router(config)#ip sla 1101
router(config-ip-sla)#ethernet y1731 delay DMM domain customer vlan 100 mpid 3101 cos 1 
router(config-sla-y1731-delay)#aggregate interval 30
router(config-sla-y1731-delay)#exit
router(config)#ip sla schedule 1102 life forever start-time now
router(config)#end
 
 

This example shows how to configure two-way delay measurement using double tagging:

router>enable
router#configure terminal
router(config)#ip sla 1101
router(config-ip-sla)#ethernet y1731 delay DMM domain customer vlan 100 inner-vlan 1101 
mpid 3101 cos 1 source mpid 4101
router(config-sla-y1731-delay)#aggregate interval 30
router(config-sla-y1731-delay)#exit
router(config)#ip sla schedule 1101 life forever start-time now
router(config)#end

Verifying Two-Way Delay Measurement Configuration

Use the following commands to verify the performance-monitoring sessions:

show run | sec ip sla

show ip sla summary

show ip sla statistics entry-number

show ip sla configuration entry-number

show ethernet cfm pm session summary

show ethernet cfm pm session detail session-id

show ethernet cfm pm session db session-id

The following are the sample outputs of the commands listed above:

Router#show run | sec ip sla
ip sla auto discovery
ip sla 1101
 ethernet y1731 delay DMM domain customer vlan 100 inner-vlan 1101 mpid 3101 cos
 1 source mpid 4101
ip sla schedule 1101 life forever start-time now
 
 
Router#show ip sla summary
IPSLAs Latest Operation Summary
Codes: * active, ^ inactive, ~ pending
 
 
ID           Type        Destination       Stats       Return      Last
                                           (ms)        Code        Run 
-----------------------------------------------------------------------
*1101        y1731-delay Domain:customer V -           OK          27 seconds ag
                         lan:100 CVlan:110                         o            
                         1 Mpid:3101                                            
 
 
Router#show ip sla statistics 
IPSLAs Latest Operation Statistics
 
 
IPSLA operation id: 1101
Delay Statistics for Y1731 Operation 1101
Type of operation: Y1731 Delay Measurement
Latest operation start time: *10:43:12.930 UTC Mon Oct 21 2013
Latest operation return code: OK
Distribution Statistics:
Interval
 Start time:  *10:43:12.930 UTC Mon Oct 21 2013
 Elapsed time: 15 seconds
 Number of measurements initiated: 7
 Number of measurements completed: 7
 Flag: OK
 
 
Router#show ip sla configuration 1101
IP SLAs Infrastructure Engine-III
Entry number: 1101
Owner: 
Tag: 
Operation timeout (milliseconds): 5000
Ethernet Y1731 Delay Operation
Frame Type: DMM
Domain: customer
Vlan: 100
CVlan: 1101
Target Mpid: 3101
Source Mpid: 4101
CoS: 1
   Max Delay: 5000
   Request size (Padding portion): 64
   Frame Interval: 1000
   Clock: Not In Sync
Threshold (milliseconds): 5000
Schedule:
   Operation frequency (seconds): 30  (not considered if randomly scheduled)
   Next Scheduled Start Time: Start Time already passed
   Group Scheduled : FALSE
   Randomly Scheduled : FALSE
   Life (seconds): Forever
   Entry Ageout (seconds): never
   Recurring (Starting Everyday): FALSE
   Status of entry (SNMP RowStatus): Active
Statistics Parameters
  Frame offset: 1
  Distribution Delay Two-Way: 
   Number of Bins 10
   Bin Boundaries: 5000,10000,15000,20000,25000,30000,35000,40000,45000,-1
  Distribution Delay-Variation Two-Way: 
   Number of Bins 10
   Bin Boundaries: 5000,10000,15000,20000,25000,30000,35000,40000,45000,-1
  Aggregation Period: 30
History
  Number of intervals: 2
 
 
Router#show ethernet cfm pm session summary
Number of Configured Session : 150
Number of Active Session: 2
Number of Inactive Session: 148
Router#
 
 
Router(config)#show ethernet cfm pm session detail 0
Session ID: 0
Sla Session ID: 1101
Level: 7
Service Type: S,C
Service Id: 100,1101
Direction: Down
Source Mac: 5352.a824.04fr
Destination Mac: 5067.a87c.fa92
Session Version: 0
Session Operation: Proactive
Session Status: Active
MPID: 4101
Tx active: yes
Rx active: yes
RP monitor Tx active: yes
RP monitor Rx active: yes
Timeout timer: stopped
Last clearing of counters: *00:00:00.000 UTC Mon Jan 1 1900
DMMs:
   Transmitted: 117       
DMRs:
   Rcvd: 117               
1DMs:
   Transmitted: 0         
   Rcvd: 0                 
LMMs:
   Transmitted: 0         
LMRs:
   Rcvd: 0                 
VSMs:
   Transmitted: 0         
VSRs:
   Rcvd: 0                 
SLMs:
   Transmitted: 0         
SLRs:
   Rcvd: 0                 
Test ID 0
Router1#
 
 
Router#show ethernet cfm pm session db 0
----------------------------------------------------------------------------
      TX Time FWD                   RX Time FWD                             
      TX Time BWD                   RX Time BWD              Frame Delay    
      Sec:nSec                      Sec:nSec                  Sec:nSec      
----------------------------------------------------------------------------
Session ID: 0
****************************************************************************
3591340722:930326034           3591340663:866791722 
3591340663:866898528           3591340722:930707484            0:274644    
****************************************************************************
3591340723:927640626           3591340664:864091056 
3591340664:864182604           3591340723:927976302            0:244128    
****************************************************************************
3591340724:927640626           3591340665:864091056 
3591340665:864167346           3591340724:927961044            0:244128    
****************************************************************************
3591340725:927671142           3591340666:864121572 
3591340666:864213120           3591340725:928006818            0:244128    
****************************************************************************
3591340726:927655884           3591340667:864106314 
3591340667:864197862           3591340726:927991560            0:244128    
****************************************************************************
3591340727:927732174           3591340668:864167346 
3591340668:864533538           3591340727:928327236            0:228870    
****************************************************************************
3591340728:927655884           3591340669:864121572 
3591340669:864197862           3591340728:928006818            0:274644    
****************************************************************************
3591340729:927671142           3591340670:864121572 
3591340670:864197862           3591340729:927991560            0:244128    
****************************************************************************

Troubleshooting Two-Way Delay Measurement Configuration

Table 4 lists the debug commands to troubleshoot issues pertaining to the two-way delay measurement configuration. The Cisco IOS Master Command List at

http://www.cisco.com/en/US/docs/ios/mcl/allreleasemcl/all_book.html provides more information about these commands.


Caution Because debugging output is assigned high priority in the CPU process, it can diminish the performance of the router or even render it unusable. For this reason, use debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff.


Note Before you run any of the debug commands listed in the following table, ensure that you run the logging buffered debugging command, and then turn off console debug logging using the no logging console command.


Table 4 debug Commands for Two-Way Delay Measurement Configuration 

debug Command
Purpose

debug epmpal all

Enables debugging of all Ethernet performance monitoring (PM) events.

debug epmpal api

Enables debugging of Ethernet PM API events.

debug epmpal rx

Enables debugging of Ethernet PM packet-receive events.

debug epmpal tx

Enables debugging of Ethernet PM packet-transmit events.