Cisco 7600-ES20 Ethernet Line Card Configuration Guide
Command Summary for the Cisco 7600 Series Ethernet Services 20G Line Card
Downloads: This chapterpdf (PDF - 99.0KB) The complete bookPDF (PDF - 4.4MB) | Feedback

Command Summary for the Cisco 7600 Series Ethernet Services 20G Line Card

Table Of Contents

Command Summary for the Cisco 7600 Series Ethernet Services 20G Line Card


Command Summary for the Cisco 7600 Series Ethernet Services 20G Line Card


Table A-1 provides an alphabetical list of some of the related commands to monitor and maintain the Cisco 7600 Series Ethernet Services 20G (ES20) line card. Table A-2 provides an alphabetical list of the EVC commands used with the ES20 line card.


Note keepalive command in the interface configuration mode is not supported in a ES20 line card.


For more information about the commands used in this chapter, see the Cisco IOS Release 12.2SR Command References at http://www.cisco.com/en/US/products/ps6922/prod_command_reference_list.html.

If a command is not located in those publications, refer to the Cisco IOS command reference and master index publications.

Table A-1 Monitoring Command Summary 

Command
Purpose

Router# hw-module module slot reset

Turns power off and on to the ES20 line card in the specified chassis slot.

Router(config)# no power enable module slot

Powers down an ES20 line card in the specified chassis slot.

Router(config)# power enable module slot

Powers on an ES20 line card in the specified chassis slot.

Router# show diagbus slot

Displays information about the ES20 line card installed in the specified chassis slot, and status of any small form-factor pluggable (SFP or XFP) optical transceivers. hardware installed in that ES20 line card.

Router# show hw-module slot slot align [cpu {0 | 1}]

Displays alignment data for an ES20 line card in the specified chassis slot.

Router# show hw-module slot slot logging [cpu {0 | 1}]

Displays logging information for an ES20 line card in the specified chassis slot.

Router# show hw-module slot slot proc cpu [cpu {0 | 1}]

Displays CPU utilization for each process on an ES20 line card in the specified chassis slot.

Router# show hw-module slot slot tech-support [cpu {0 | 1}]

Displays system information to troubleshoot a problem for an ES20 line card in the specified chassis slot.

Router# show idprom module slot [clei]

Displays IDPROM information for an ES20 line card in the specified chassis slot, and optionally any Common Language Equipment Identification (CLEI) information for the ES20 line card.

Router# show module [slot | all | version]

Displays status and information for an ES20 line card in the specified chassis slot.


Table A-2 EVC Command Summary 

Command
Purpose

Router(config-if-srv)# [bridge-domain bridge-id

Binds the service instance to a bridge-domain instance.

Router(config-if-srv)# connect evc-name interface1 efp-id1 interface2 efp-id2

Creates a direct and transparent connection between two service instances.

Router#debug ethernet service evc [id evc-id]

Enables Ethernet virtual connection (EVC) debugging. If no EVC ID is specified, debugging is enabled for all EVCs on the system.

Router#debug ethernet service instance [id instance-id interface interface-id | interface interface-id]

Enables service instance debugging. If no options are specified, debugging for all service instances is enabled. If a service instance ID and interface are specified, only debug messages for the associated service instance are output. If only an interface is specified, debug messages for all service instances on that interface are displayed.

Router#debug ethernet service interface [interface-id]

Enables Port Data Block (PDB) debugging.

Router#debug ethernet service api

Enables debugging between Ethernet Services Infrastructure and its clients.

Router#debug ethernet service oam-mgr

Enables OAM Manager debugging, to debug OAM inter-working.

Router#debug ethernet service error

Enables ethernet service error debugging.

Router#debug ethernet service all

Enables all EI debugging messages for all PDBs, EVCs and service instances.

Router#ethernet evc service-name

Creates an EVC (or a Customer Service Instance) on global configuration mode. It sets the device into the config-srv submode.

Router(config-if-srv)#encapsulation untagged

Defines the matching criteria to be used in order to map untagged Ethernet frames ingress on an interface to the appropriate service instance.

Router(config-if-srv)#encapsulation default

Configures the default service instance on a port. Anything that does not meet the criteria of other service instances on the same physical interface falls into this service instance

Router(config-if-srv)#encapsulation dot1q vlan-id[,vlan-id[-vlain-id]] [native]

Defines the matching criteria to be used in order to map dot1q frames ingress on an interface to the appropriate service instance. The criteria for this command are: single VLAN, range of VLANs and lists of the previous two.

Router(config-if-srv)#encapsulation dot1ad vlan-id[,vlan-id[-vlain-id]] [native]

Defines the matching criteria to be used in order to map single-tagged 802.1ad frames ingress on an interface to the appropriate service instance. The criteria for this command are: single VLAN, range of VLANs and lists of the previous two.

Router(config-if-srv)#encapsulation dot1q <vlan-id> second-dot1q {any | vlan-id[,vlan-id[-vlain-id]]}

Defines the matching criteria to be used in order to map QinQ frames ingress on an interface to the appropriate service instance. The criteria for this command are: outer tag must be unique and inner tag may be single VLAN, range of VLANs or lists of the previous two.

Router(config-if-srv)#encapsulation dot1ad <vlan-id> dot1q {any | vlan-id[,vlan-id[-vlain-id]]}

Defines the matching criteria to be used in order to map double-tagged 802.1ad frames ingress on an interface to the appropriate service instance. The criteria for this command are: outer tag must be unique and inner tag may be single VLAN, range of VLANs or lists of the previous two.

Router(config-if-srv)#rewrite ingress tag {push {dot1q vlan-id | dot1q vlan-id second-dot1q vlan-id | dot1ad vlan-id dot1q vlan-id} | pop {1 | 2} | translate {1-to-1 {dot1q vlan-id | dot1ad vlan-id}| 2-to-1 dot1q vlan-id | dot1ad vlan-id}| 1-to-2 {dot1q vlan-id second-dot1q vlan-id | dot1ad vlan-id dot1q vlan-id} | 2-to-2 {dot1q vlan-id second-dot1q vlan-id | dot1ad vlan-id dot1q vlan-id}} [symmetric]

Specifies the encapsulation adjustment that is to be performed on the frame ingress to the service instance.

Router(config-if-srv)#service instance id {Ethernet [service-name]}

Creates an service instance (instantiation of an EVC) on an interface. It sets the device into the config-if-srv sub-mode.

Router#show ethernet service evc [id evc-id | interface interface-id] [detail]

Displays information pertaining to a specific EVC if an EVC ID is specified, or pertaining to all EVCs on an interface if an interface is specified. The detailed option provides additional information on the EVC.

Router#show ethernet service instance [id <instance-id> interface interface-id | interface interface-id] [detail]

Displays information about one or more service instances: If a service instance ID and interface are specified, only data pertaining to that particular service instance will be displayed. If only an interface ID is specified, this command will display data for all service instances on the given interface.

Router#show ethernet service interface [interface-id] [detail]

Displays information in the PDB.

Router(config-if-srv)#xconnect peer-id vc-id encapsulation mpls

Configures scalable EoMPLS on a service instance. On the ingress side, after proper encapsulation manipulations, the packet is tunneled in a EoMPLS VC and transmitted on the core.