Guest

Cisco 7200 Series Routers

Cisco 7200 Regulatory Compliance and Safety Information

  • Viewing Options

  • PDF (5.9 MB)
  • Feedback
Regulatory Compliance and Safety Information for Cisco 7200 Series Routers

Table Of Contents

Regulatory Compliance and Safety Information for Cisco 7200 Series Routers

Document Revision History

Translated Safety Warnings

Statement 2—Chassis Warning—Disconnecting Telephone-Network Cables

Statement 10—Installation Warning

Statement 12—Power Supply Disconnection Warning

Statement 14—Electric Shock Warning

Statement 22—SELV Circuit Warning

Statement 33—Battery Handling Warning

Statement 37—Restricted Area Warning

Statement 42—Ground Connection Warning

Statement 70—Invisible Laser Radiation Warning

Statement 83—Power Cord Caution

Statement 94—Wrist Strap Warning

Statement 122—Exposed DC Power Wire Warning

Statement 140—Chassis Power Connection

Statement 163—Chassis Lifting Warning

Statement 164—Two Person Lifting Requirement

Statement 188—AC Power Supply Warning

Statement 200—Safety Information Referral Warning

Statement 202—Ground Connection Warning

Statement 212—Unit Connection Warning

Statement 322—DC Power Off Warning

Statement 1001—Work During Lightning Activity

Statement 1003—DC Power Disconnection

Statement 1005—Circuit Breaker

Statement 1008—Class 1 Laser Product

Statement 1021—SELV Circuit

Statement 1024—Ground Conductor

Statement 1027—Class 1 LED Product

Statement 1028—More Than One Power Supply

Statement 1030—Equipment Installation

Statement 1040—Product Disposal

Statement 1046—Installing or Replacing the Unit

Statement 1050—Power Module

Statement 1051—Laser Radiation

Statement 1071—Warning Definition

Statement 1074—Comply with Local and National Electrical Codes

Japanese Electric Appliance and Radio Laws

Statement 371—Power Cable and AC Adapter

European Directives

Statement 275—Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as Amended by Directive 93/68/EEC

Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein

California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)

Regulatory Standards Compliance

EMC Environmental Conditions for Products Installed in the European Union

EMC Class A Statements/Warnings

FCC Class A

Canada - Class A

Statement 191—VCCI Class A Warning for Japan

Statement 256—Class A Warning for Hungary

Statement 257—Class A Notice for Taiwan and Other Traditional Chinese Markets

Statement 294—Class A Warning for Korea

Statement 340—Class A Warning for CISPR22

Network Equipment Building System (NEBS)

Telecom Approvals Listing

FCC Part 68 Notice

Canada - CS-03 Certification

Japan - JATE Certification

Korea - RRL Certification

Site Preparation and Safety Information

Preparing Your Site for Installation

Choosing a Site for Installation

Ensuring Overcurrent Protection

Grounding the System

Creating a Safe Environment

Rack-Mounting the System

Ensuring Proper Airflow

Stabilizing the System

Lifting the System

Power Considerations

AC Power

DC Power

Redundant Power

Preventing ESD

Installing and Servicing the System

Disconnecting Power

Working with WAN Interfaces

Working with Lasers

Preventing EMI

Covering Empty Slots

Disposing of the System

Related Documentation

Obtaining Documentation and Submitting a Service Request


Regulatory Compliance and Safety Information for Cisco 7200 Series Routers


Read this document before installing or servicing the following Cisco 7200 series routers:

Cisco 7201

Cisco 7202

Cisco 7204

Cisco 7206

Cisco 7204VXR

Cisco 7206VXR

Document Revision History

The Document Revision History below, beginning with online part number 78-3419-15, records technical changes to this document.

Revision
Date
Change Summary

78-3419-19

March 2008

Updated NEBS information.

78-3419-18

April, 2007

Added Cisco 7201 information and updated Telecom information.

78-3419-17

December, 2007

Added PA-MC-T3-EC information changes.

78-3419-16

November, 2006

Updated updates safety information to Table 1, ETS EN 300 386 to Table 2, and Statement 371.

78-3419-15

May, 2006

Added NPE-G2 memory information.



Note The Cisco 7206 can be used as a router shelf in a Cisco AS5800 Universal Access Server. References to Cisco 7200 series routers in this document include the Cisco 7206 router shelf, unless indicated otherwise.



Note Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS 3260) should install, replace, or service the equipment. Install the system in accordance with the U.S. National Electric Code if you are in the United States.



Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.


This document includes the following sections:

Translated Safety Warnings

Japanese Electric Appliance and Radio Laws

European Directives

California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)

Regulatory Standards Compliance

EMC Environmental Conditions for Products Installed in the European Union

EMC Class A Statements/Warnings

Network Equipment Building System (NEBS)

Telecom Approvals Listing

Site Preparation and Safety Information

Related Documentation

Obtaining Documentation and Submitting a Service Request

Translated Safety Warnings

This section repeats, in multiple languages, the warnings in this document. In addition, this section contains translated warnings that can be used with other documentation related to Cisco 7200 series routers, such as the documents for Cisco 7200 series routers field-replaceable units.

The following translated safety warnings are in this section:

Statement 2—Chassis Warning—Disconnecting Telephone-Network Cables

Statement 10—Installation Warning

Statement 12—Power Supply Disconnection Warning

Statement 14—Electric Shock Warning

Statement 22—SELV Circuit Warning

Statement 33—Battery Handling Warning

Statement 37—Restricted Area Warning

Statement 42—Ground Connection Warning

Statement 70—Invisible Laser Radiation Warning

Statement 83—Power Cord Caution

Statement 94—Wrist Strap Warning

Statement 122—Exposed DC Power Wire Warning

Statement 140—Chassis Power Connection

Statement 163—Chassis Lifting Warning

Statement 164—Two Person Lifting Requirement

Statement 188—AC Power Supply Warning

Statement 200—Safety Information Referral Warning

Statement 202—Ground Connection Warning

Statement 212—Unit Connection Warning

Statement 322—DC Power Off Warning

Statement 1001—Work During Lightning Activity

Statement 1003—DC Power Disconnection

Statement 1005—Circuit Breaker

Statement 1008—Class 1 Laser Product

Statement 1021—SELV Circuit

Statement 1024—Ground Conductor

Statement 1027—Class 1 LED Product

Statement 1028—More Than One Power Supply

Statement 1030—Equipment Installation

Statement 1040—Product Disposal

Statement 1046—Installing or Replacing the Unit

Statement 1050—Power Module

Statement 1051—Laser Radiation

Statement 1071—Warning Definition

Statement 1074—Comply with Local and National Electrical Codes

Statement 2—Chassis Warning—Disconnecting Telephone-Network Cables

Warning


Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages.

Waarschuwing

Voordat u het frame opent, dient u de verbinding met het telefoonnetwerk te verbreken door de kabels te ontkoppelen om zo contact met telefoonnetwerk-spanningen te vermijden.

Varoitus

Vältä joutumista kosketuksiin puhelinverkostojännitteiden kanssa irrottamalla puhelinverkoston kaapelit ennen asennuspohjan aukaisemista.

Attention

Avant d'ouvrir le châssis, débrancher les câbles du réseau téléphonique afin d'éviter tout contact avec les tensions d'alimentation du réseau téléphonique.

Warnung

Bevor Sie das Chassis öffnen, ziehen Sie die Telefonnetzkabel aus der Verbindung, um Kontakt mit Telefonnetzspannungen zu vermeiden.

Figyelem!

Mielõtt kinyitná a készülék házát, a telefonhálózati feszültséggel való érintkezés elkerülése érdekében távolítsa el a csatlakozókból a telefonhálózati kábeleket.

Avvertenza

Prima di aprire il telaio, scollegare i cavi della rete telefonica per evitare di entrare in contatto con la tensione di rete.

Advarsel

Før kabinettet åpnes, skal kablene for telenettet kobles fra for å unngå å komme i kontakt med spenningen i telenettet.

Aviso

Antes de abrir o chassis, desligue os cabos da rede telefónica para evitar contacto com a tensão da respectiva rede.

¡Advertencia!

Antes de abrir el chasis, desconectar el cableado dirigido a la red telefónica para evitar contacto con voltajes de la propia red.

Varning!

Koppla loss ledningarna till telefonnätet innan du öppnar chassit så att kontakten med telefonnätsspänningen bryts.

 



Statement 10—Installation Warning

Warning


Read the installation instructions before you connect the system to its power source.

Waarschuwing

Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt.

Varoitus

Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.

Warnung

Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschließen.

Avvertenza

Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.

Advarsel

Les installasjonsinstruksjonene før systemet kobles til strømkilden.

Aviso

Leia as instruções de instalação antes de ligar o sistema à sua fonte de energia.

¡Advertencia!

Ver las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

Varning!

Läs installationsanvisningarna innan du kopplar systemet till dess strömförsörjningsenhet.

 



Statement 12—Power Supply Disconnection Warning

Warning


Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units.

Waarschuwing

Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen de stekker van het netsnoer uit het stopcontact te halen; voor gelijkstroom toestellen dient u de stroom uit te schakelen bij de stroomverbreker.

Varoitus

Kytke irti vaihtovirtalaitteiden virtajohto ja katkaise tasavirtalaitteiden virta suojakytkimellä, ennen kuin teet mitään asennuspohjalle tai työskentelet virtalähteiden läheisyydessä.

Attention

Avant de travailler sur un châssis ou à proximité d'une alimentation électrique, débrancher le cordon d'alimentation des unités en courant alternatif ; couper l'alimentation des unités en courant continu au niveau du disjoncteur.

Warnung

Bevor Sie an einem Chassis oder in der Nähe von Netzgeräten arbeiten, ziehen Sie bei Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei Gleichstromeinheiten den Strom am Unterbrecher ab.

Figyelem!

Mielõtt elkezdene dolgozni a házon vagy tápegységek közelében, húzza ki a váltóáramú készülékek tápkábelét; egyenáramú készülék esetén szakítsa meg az áramot az árammegszakítónál

Avvertenza

Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle unità CA; scollegare l'alimentazione all'interruttore automatico sulle unità CC.

Advarsel

Før det utføres arbeid på kabinettet eller det arbeides i nærheten av strømforsyningsenheter, skal strømledningen trekkes ut på vekselstrømsenheter og strømmen kobles fra ved strømbryteren på likestrømsenheter.

Aviso

Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de energia, desligue o cabo de alimentação nas unidades de corrente alternada; desligue a corrente no disjuntor nas unidades de corrente contínua.

¡Advertencia!

Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentación, desenchufar el cable de alimentación en los equipos de corriente alterna (CA); cortar la alimentación desde el interruptor automático en los equipos de corriente continua (CC).

Varning!

Innan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du för växelströmsenheter dra ur nätsladden och för likströmsenheter bryta strömmen vid överspänningsskyddet.

 



Statement 14—Electric Shock Warning

Warning This unit might have more than one power cord. To reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit.

Waarschuwing

Dit toestel kan meer dan één netsnoer hebben. Om het risico van een elektrische schok te verminderen, dient u de stekkers van de twee netsnoeren uit het stopcontact te halen voordat u het toestel een servicebeurt geeft.

Varoitus

Tässä laitteessa saattaa olla useampi kuin yksi virtajohto. Irrota molemmat virtalähteestä tulevat johtimet ennen laitteen huoltamista, jotta vältät sähköiskun vaaran.

Attention

Il est possible que cette unité soit munie de plusieurs cordons d'alimentation. Pour éviter les risques d'électrocution, débrancher les deux cordons d'alimentation avant de réparer l'unité.

Warnung

Diese Einheit hat möglicherweise mehr als ein Netzkabel. Zur Verringerung der Stromschlaggefahr trennen Sie beide Netzgerätekabel ab, bevor Sie die Einheit warten.

Avvertenza

Questa unità potrebbe essere dotata di più di un cavo di alimentazione. Per ridurre il rischio di scossa elettrica, scollegare i due cavi di alimentazione prima di procedere alla manutenzione dell'unità.

Advarsel

Denne enheten kan være utstyrt med mer enn én strømledning. Koble fra de to strømledningene før det utføres reparasjonsarbeid på enheten for å redusere faren for elektriske støt.

Aviso

Esta unidade poderá ter mais do que um cabo de alimentação. Para reduzir o risco de choque eléctrico, desligue os dois cabos de alimentação antes de efectuar reparações na unidade.

¡Advertencia!

Puede ser que este equipo posea más de un cable de alimentación. Para reducir el riesgo de descarga eléctrica, desenchufar los dos cables antes de proceder al mantenimiento de la unidad.

Varning!

Denna enhet kan vara försedd med mer än en nätsladd. För att minska risken för elektriska stötar skall båda nätsladdarna dras ur innan du utför underhållsarbete på enheten.


Statement 22—SELV Circuit Warning

Warning


The ports labeled "Ethernet," "10BaseT," "Token Ring," "Console," and "AUX" are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits.

Waarschuwing

De poorten die "Ethernet", "10BaseT", "Token Ring", "Console" en "AUX" zijn gelabeld, zijn veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage). SELV-circuits mogen alleen met andere SELV-circuits verbonden worden. Omdat de BRI-circuits op dezelfde manier als telefoonnetwerkspanning behandeld worden, mag u het SELV-circuit niet verbinden met de telefoonnetwerkspanning (TNV) circuits.

Varoitus

Portit, joissa on nimet "Ethernet", "10BaseT", "Token Ring", "Console" ja "AUX", ovat erityisen pienen jännityksen omaavia turvallisuuspiirejä (SELV-piirejä). Tällaiset SELV-piirit tulee yhdistää ainoastaan muihin SELV-piireihin. Koska perusluokan liitäntöjen (Basic Rate Interface- eli BRI-liitännät) jännite vastaa puhelinverkoston jännitettä, vältä SELV-piirin yhdistämistä puhelinverkoston jännitepiireihin (TNV-piireihin).

Attention

Les ports étiquetés « Ethernet », « 10BaseT », « Token Ring », « Console » et « AUX » sont des circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV). Les circuits SELV ne doivent être interconnectés qu'avec d'autres circuits SELV. Comme les circuits BRI sont considérés comme des sources de tension de réseau téléphonique, éviter de connecter un circuit SELV à un circuit de tension de réseau téléphonique (telephone network voltage ou TNV).

Warnung

Die mit "Ethernet", "10BaseT", "Token Ring", "Console" und "AUX" beschrifteten Buchsen sind Sicherheitskreise mit Sicherheitskleinspannung (Safety Extra-Low Voltage, SELV). SELV-Kreise sollten ausschließlich an andere SELV-Kreise angeschlossen werden. Da die BRI-Kreise wie Telefonnetzspannungen behandelt werden, ist der SELV-Kreis nicht an Telefonnetzspannungskreise (TNV) anzuschließen.

Avvertenza

Le porte contrassegnate da "Ethernet", "10BaseT", "TokenRing", "Console" e "AUX" sono circuiti di sicurezza con tensione molto bassa (SELV). I circuiti SELV devono essere collegati solo ad altri circuiti SELV. Dato che i circuiti BRI vengono trattati come tensioni di rete telefonica, evitare di collegare il circuito SELV ai circuiti in cui è presente le tensione di rete telefonica (TNV).

Advarsel

Utgangene merket "Ethernet", "10BaseT", "Token Ring", "Console" og "AUX" er lavspentkretser (SELV) for ekstra sikkerhet. SELV-kretser skal kun kobles til andre SELV-kretser. Fordi BRI-kretsene håndteres som telenettspenning, unngå å koble SELV-kretsen til kretser for telenettspenning (TNV).

Aviso

As portas "Ethernet", "10BaseT", "Token Ring", "Console", and "AUX" são circuitos de segurança de baixa tensão (SELV). Estes circuitos deverão ser apenas ligados a outros circuitos SELV. Devido ao facto de os circuitos BRI (Interface de Ritmo Básico) serem tratados como sendo de tensão equivalente à da rede telefónica, evite ligar o circuito SELV aos circuitos TNV (tensão de rede telefónica).

¡Advertencia!

Los puertos "Ethernet", "10BaseT", "Token Ring", "Console" y "AUX" son circuitos de muy baja señal que garantizan ausencia de peligro (Safety Extra-Low Voltage = SELV). Estos circuitos SELV deben ser conectados exclusivamente con otros también de tipo SELV. Puesto que los circuitos tipo BRI se comportan como aquéllos con voltajes de red telefónica, debe evitarse conectar circuitos SELV con circuitos de voltaje de red telefónica (TNV).

Varning!

De portar som är märkta "Ethernet", "10BaseT", "Token Ring", "Console" och "AUX" är SELV-kretsar, d.v.s. skyddskretsar med extra låg spänning (SELV: Safety Extra-Low Voltage = skyddsklenspänning). SELV-kretsar får endast anslutas till andra SELV-kretsar. Eftersom BRI-kretsar behandlas liksom telefonnätsspänning bör SELV-kretsen inte anslutas till telefonnätsspänningskretsar (TNV-kretsar).



Statement 33—Battery Handling Warning

Warning


There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Waarschuwing

Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden.

Varoitus

Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä vaihtamiseen ainoastaan saman- tai vastaavantyyppistä akkua, joka on valmistajan suosittelema. Hävitä käytetyt akut valmistajan ohjeiden mukaan.

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant.

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Avvertenza

Pericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.

Advarsel

Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.

Aviso

Existe perigo de explosão se a bateria for substituída incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas conforme as instruções do fabricante.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.

Varning!

Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med samma batterityp som rekommenderas av tillverkaren eller motsvarande. Följ tillverkarens anvisningar vid kassering av använda batterier.



Statement 37—Restricted Area Warning

Warning


This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.

Waarschuwing

Dit toestel is bedoeld voor installatie op plaatsen met beperkte toegang. Een plaats met beperkte toegang is een plaats waar toegang slechts door servicepersoneel verkregen kan worden door middel van een speciaal instrument, een slot en sleutel, of een ander veiligheidsmiddel, en welke beheerd wordt door de overheidsinstantie die verantwoordelijk is voor de locatie.

Varoitus

Tämä laite on tarkoitettu asennettavaksi paikkaan, johon pääsy on rajoitettua. Paikka, johon pääsy on rajoitettua, tarkoittaa paikkaa, johon vain huoltohenkilöstö pääsee jonkin erikoistyökalun, lukkoon sopivan avaimen tai jonkin muun turvalaitteen avulla ja joka on paikasta vastuussa olevien toimivaltaisten henkilöiden valvoma.

Attention

Cet appareil est à installer dans des zones d'accès réservé. Ces dernières sont des zones auxquelles seul le personnel de service peut accéder en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout autre moyen de sécurité. L'accès aux zones de sécurité est sous le contrôle de l'autorité responsable de l'emplacement.

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Ein Bereich mit beschränktem Zutritt ist ein Bereich, zu dem nur Wartungspersonal mit einem Spezialwerkzeugs, Schloß und Schlüssel oder anderer Sicherheitsvorkehrungen Zugang hat, und der von dem für die Anlage zuständigen Gremium kontrolliert wird.

Avvertenza

Questa unità deve essere installata in un'area ad accesso limitato. Un'area ad accesso limitato è un'area accessibile solo a personale di assistenza tramite un'attrezzo speciale, lucchetto, o altri dispositivi di sicurezza, ed è controllata dall'autorità responsabile della zona.

Advarsel

Denne enheten er laget for installasjon i områder med begrenset adgang. Et område med begrenset adgang gir kun adgang til servicepersonale som bruker et spesielt verktøy, lås og nøkkel, eller en annen sikkerhetsanordning, og det kontrolleres av den autoriteten som er ansvarlig for området.

Aviso

Esta unidade foi concebida para instalação em áreas de acesso restrito. Uma área de acesso restrito é uma área à qual apenas tem acesso o pessoal de serviço autorizado, que possua uma ferramenta, chave e fechadura especial, ou qualquer outra forma de segurança. Esta área é controlada pela autoridade responsável pelo local.

¡Advertencia!

Esta unidad ha sido diseñada para instalarse en áreas de acceso restringido. Área de acceso restringido significa un área a la que solamente tiene acceso el personal de servicio mediante la utilización de una herramienta especial, cerradura con llave, o algún otro medio de seguridad, y que está bajo el control de la autoridad responsable del local.

Varning!

Denna enhet är avsedd för installation i områden med begränsat tillträde. Ett område med begränsat tillträde får endast tillträdas av servicepersonal med ett speciellt verktyg, lås och nyckel, eller annan säkerhetsanordning, och kontrolleras av den auktoritet som ansvarar för området.



Statement 42—Ground Connection Warning

Warning


When installing the unit, always make the ground connection first and disconnect it last.

Waarschuwing

Bij de installatie van het toestel moet de aardverbinding altijd het eerste worden gemaakt en het laatste worden losgemaakt.

Varoitus

Laitetta asennettaessa on maahan yhdistäminen aina tehtävä ensiksi ja maadoituksen irti kytkeminen viimeiseksi.

Attention

Lors de l'installation de l'appareil, la mise à la terre doit toujours être connectée en premier et déconnectée en dernier.

Warnung

Der Erdanschluß muß bei der Installation der Einheit immer zuerst hergestellt und zuletzt abgetrennt werden.

Figyelem!

A készülék üzembe helyezése közben mindig a földelõvezetéket kell elsõként csatlakoztatni és azt kell utolsóként leválasztani.

Avvertenza

In fase di installazione dell'unità, eseguire sempre per primo il collegamento a massa e disconnetterlo per ultimo.

Advarsel

Når enheten installeres, må jordledningen alltid tilkobles først og frakobles sist.

Aviso

Ao instalar a unidade, a ligação à terra deverá ser sempre a primeira a ser ligada, e a última a ser desligada.

¡Advertencia!

Al instalar el equipo, conectar la tierra la primera y desconectarla la última.

Varning!

Vid installation av enheten måste jordledningen alltid anslutas först och kopplas bort sist.

 



Statement 70—Invisible Laser Radiation Warning

Warning


Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures.

Waarschuwing

Omdat er onzichtbare laserstraling uit de opening van de poort geëmitteerd kan worden wanneer er geen kabel aangesloten is, dient men om blootstelling aan laserstraling te vermijden niet in de open openingen te kijken.

Varoitus

Kun porttiin ei ole kytketty kaapelia, portin aukosta voi vuotaa näkymätöntä lasersäteilyä. Älä katso avoimiin aukkoihin, jotta et altistu säteilylle.

Attention

Etant donné qu'un rayonnement laser invisible peut être émis par l'ouverture du port quand aucun câble n'est connecté, ne pas regarder dans les ouvertures béantes afin d'éviter tout risque d'exposition au rayonnement laser.

Warnung

Aus der Öffnung des Ports kann unsichtbare Laserstrahlung austreten, wenn kein Kabel angeschlossen ist. Kontakt mit Laserstrahlung vermeiden und nicht in offene Öffnungen blicken.

Avvertenza

Poiché quando nessun cavo è collegato alla porta, da quest'ultima potrebbe essere emessa radiazione laser invisibile, evitare l'esposizione a tale radiazione e non fissare con gli occhi porte a cui non siano collegati cavi.

Advarsel

Usynlige laserstråler kan sendes ut fra åpningen på utgangen når ingen kabel er tilkoblet. Unngå utsettelse for laserstråling og se ikke inn i åpninger som ikke er tildekket.

Aviso

Evite uma exposição à radiação laser e não olhe através de aberturas expostas, porque poderá ocorrer emissão de radiação laser invisível a partir da abertura da porta, quando não estiver qualquer cabo conectado.

¡Advertencia!

Cuando no esté conectado ningún cable, pueden emitirse radiaciones láser invisibles por el orificio del puerto. Evitar la exposición a radiaciones láser y no mirar fijamente los orificios abiertos.

Varning!

Osynliga laserstrålar kan sändas ut från öppningen i porten när ingen kabel är ansluten. Undvik exponering för laserstrålning och titta inte in i ej täckta öppningar.



Statement 83—Power Cord Caution


Caution This unit might have more than one power cord. To reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit.

 



Statement 94—Wrist Strap Warning

Warning


During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.

Waarschuwing

Draag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.

Varoitus

Käytä tämän toimenpiteen aikana maadoitettuja rannesuojia estääksesi kortin vaurioitumisen sähköstaattisen purkauksen vuoksi. Älä kosketa taustalevyä suoraan kädelläsi tai metallisella työkalulla sähköiskuvaaran takia.

Attention

Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n'endommagent la carte. Pour éviter l'électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique.

Warnung

Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder einem metallenen Werkzeug besteht Elektroschockgefahr.

Figyelem!

Az elektromos kisülés okozta meghibásodás elkerülése érdekében az eljárás során viseljen földelõ csuklópántot. Se kézzel, se fém eszközzel ne érjen hozzá a kártya hátlapjához, mert különben áramütést szenvedhet.

Avvertenza

Durante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da un'eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, né con le mani né con un qualsiasi utensile metallico, perché esiste il pericolo di folgorazione.

Advarsel

Bruk jordingsarmbånd under prosedyren for å unngå ESD-skader på kortet. Unngå direkte berøring av bakplanet med hånden eller metallverktøy, slik at di ikke får elektrisk støt.

Aviso

Durante este procedimento e para evitar danos ESD causados à placa, use fitas de ligação à terra para os pulsos. Para evitar o risco de choque eléctrico, não toque directamente na parte posterior com a mão ou com qualquer ferramenta metálica.

¡Advertencia!

Usartiras conectadas a tierra en las muñecas durante este procedimiento para evitar daños en la tarjeta causados por descargas electrostáticas. No tocar el plano posterior con las manos ni con ninguna herramienta metálica, ya que podría producir un choque eléctrico.

Varning!

Använd jordade armbandsremmar under denna procedur för att förhindra elektrostatisk skada på kortet. Rör inte vid baksidan med handen eller metallverktyg då detta kan orsaka elektrisk stöt.

 



Statement 122—Exposed DC Power Wire Warning

Warning


An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug.

Waarschuwing

Een blootgestelde verbindingsdraad van een ingangsgelijkstroombron kan gevaarlijke elektriciteitsniveaus geleiden. Zorg ervoor dat geen blootgesteld deel van het draad van de ingangsgelijkstroombron zich uitstrekt vanuit het aansluitblok van de terminal.

Varoitus

Tasavirtalähteestä tuleva avoin johto voi johtaa vaarallisen määrän sähköä. Varmista, ettei kaapelikengän pistokkeesta tule esille lainkaan tasavirtajohdon avointa osaa.

Attention

Pour éviter tout risque de choc électrique, vérifiez que les câbles d'alimentation secteur sont protégés par une gaine. Aucun fil dénudé ne doit apparaître hors du bloc d'alimentation du terminal.

Warnung

Eine ungeschützte Kabelleitung von einer Gleichstrom-Eingangsspannungsquelle kann schädliche Elektrizitätslevel führen. Achten Sie darauf, daß von dem Klemmleistenstecker aus kein ungeschütztes Eingangsgleichstromkabel freiliegt.

Figyelem!

Az egyenáramú tápegység egyik hozzáférhetõ vezetéke veszélyes áramerõsségû lehet. Gyõzõdjön meg róla, hogy az egyenáramú tápegység egyik vezetéke sem lóg ki a sorkapocsból.

Avvertenza

Un cavo elettrico scoperto proveniente da un alimentatore DC-INPUT può trasmettere scariche elettriche ad elevata tensione. Assicuratevi che i cavi in uscita dall'alimentatore DC-input non presentino punti scoperti.

Advarsel

En avdekket ledning fra en likestrømskilde kan lede farlig elektrisitet. Kontroller at ingen avdekkede deler av ledningen til likestrømskilden stikker ut av terminalens koblingsblokk.

Aviso

Um fio condutor exposto de uma unidade de entrada de DC (corrente contínua) pode transportar níveis perigosos de electricidade. Certifique-se de que nenhuma secção exposta de um fio condutor da fonte de energia de entrada de DC se extende a partir da ficha da placa de terminais.

¡Advertencia!

Un cable desnudo de una fuente de entrada de alimentación de corriente directa (DC) puede conducir niveles de electricidad peligrosos. Asegúrese de que ninguna parte del cable de la fuente de alimentación de DC de entrada sale del enchufe del bloque de terminal.

Varning!

En blottad trådledning från en likströmsförsörjningsenhet kan utgöra en ledare för skadliga elektricitetsnivåer. Se till att inte någon blottad ledningsdel från likströmsförsörjningsenheten sticker ut från stiftplinten.

 



Statement 140—Chassis Power Connection

Warning Before connecting or disconnecting ground or power wires to the chassis, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.

Waarschuwing

Voordat u aarddraden of elektriciteitsdraden op het frame aansluit of van het frame neemt, dient u te controleren of de stroom naar het gelijkstroomcircuit uitgeschakeld is. Om u ervan te verzekeren dat alle stroom UIT is geschakeld, kiest u op het schakelbord de stroomverbreker die het gelijkstroomcircuit bedient, draait de stroomverbreker naar de UIT positie en plakt de schakelaarhendel van de stroomverbreker met plakband in de UIT positie vast.

Varoitus

Varmista, että tasavirtapiirissä ei ole virtaa ennen maadoitus- tai virtajohtojen kytkemistä asennuspohjaan tai ennen niiden irrottamista. Varmistaaksesi, että virta on KATKAISTU täysin, paikanna tasavirrasta huolehtivassa kojetaulussa sijaitseva suojakytkin, käännä suojakytkin KATKAISTU-asentoon ja teippaa suojakytkimen varsi niin, että se pysyy KATKAISTU-asennossa.

Attention

Avant de connecter ou de déconnecter les câbles d'alimentation (pôles et terre) du châssis, vérifiez que le circuit de courant continu est hors tension : localisez le disjoncteur sur le panneau de commande du circuit de courant continu, poussez-le sur la position fermée (OFF) et, à l'aide d'un ruban adhésif, bloquez sa poignée sur cette position.

Warnung

Gleichstrom-Unterbrechung Bevor Sie Erdungs- oder Stromkabel an das Chassis anschließen oder von ihm abtrennen, ist sicherzustellen, daß der Gleichstrom-Stromkreis unterbrochen ist. Um sicherzustellen, daß sämtlicher Strom AUS ist, machen Sie auf der Schalttafel den Unterbrecher für die Gleichstromschaltung ausfindig, stellen Sie den Unterbrecher auf OFF, und kleben Sie den Schaltergriff des Unterbrechers mit Klebeband in der AUS-Stellung fest.

Avvertenza

Prima di collegare o distaccare i cavi elettrici o di messa a terra dallo chassis, assicuratevi che il circuito DC non sia alimentato. Per verificare che tutta l'alimentazione sia scollegata (OFF), individuare l'interruttore automatico sul quadro strumenti che alimenta il circuito CC, mettere l'interruttore in posizione OFF e fissarlo con nastro adesivo in tale posizione.

Advarsel

Før til- eller frakobling av jord- og strømledninger til kabinettet, kontroller at strømmen er frakoblet likestrømkretsen. Sørg for at all strøm er slått AV. Dette gjøres ved å lokalisere strømbryteren på brytertavlen som betjener likestrømkretsen, slå strømbryteren AV og teipe bryterhåndtaket på strømbryteren i AV-stilling.

Aviso

Antes de conectar ou desconectar a ligação à terra ou a alimentação do chassis, certifique-se de que desligou a fonte de alimentação de energia do circuito de corrente contínua. Para se assegurar que toda a corrente foi DESLIGADA, localize o disjuntor no painel que serve o circuito de corrente contínua e coloque-o na posição OFF (Desligado), segurando nessa posição a manivela do interruptor do disjuntor com fita isoladora.

¡Advertencia!

Antes de conectar o desconectar el circuito de tierra o de alimentación del chasis, asegúrese que la alimentación del circuito CC esté cortada (OFF). Para asegurarse de que toda la alimentación esté cortada (OFF), localice el interruptor automático en el panel que alimenta el circuito de corriente continua, cambie el interruptor automático a la posición de apagado (OFF) y sujete con cinta la palanca del interruptor automático en posición de apagado (OFF).

Varning!

Innan du kopplar jord- eller elledningar till eller från chassit måste du kontrollera att strömförsörjningen till likströmskretsen är bruten. Kontrollera att all strömförsörjning är BRUTEN genom att slå AV det överspänningsskydd som skyddar likströmskretsen och tejpa fast överspänningsskyddets omkopplare i FRÅN-läget.


Statement 163—Chassis Lifting Warning

Warning


To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge.

Waarschuwing

Om persoonlijk letsel of schade aan het chassis te voorkomen, dient u het chassis nooit aan de handvatten op de modules (zoals stroomvoorzieningen, ventilators of kaarten) op te tillen of te kantelen; deze handvatten zijn niet ontworpen om het gewicht van de eenheid te dragen. Til de eenheid alleen op aan de handvatten die een integraal deel uitmaken van het chassis of door het chassis bij zijn onderste rand vast te grijpen.

Varoitus

Henkilövaurioiden ja asennuspohjan vahingoittumisen estämiseksi ei asennuspohjaa saa nostaa tai kallistaa moduulien kahvoista (esim. virtalähteiden, tuulettimien tai korttien kahvoista). Nämä kahvat eivät kestä koko laitteen painoa. Nosta laite ainoastaan asennuspohjan kahvoista tai tarttumalla kiinni asennuspohjan alalaidasta.

Attention

Pour éviter tout risque d'accident corporel et/ou de dommage matériel, n'essayez jamais de soulever ou de faire pivoter le châssis par les poignées des différents modules (blocs d'alimentation, ventilateurs ou cartes). Celles-ci ne sont pas conçues pour supporter le poids de l'unité. Soulevez l'unité uniquement par les poignées du châssis lui-même ou en portant celui-ci par le bord inférieur.

Warnung

Um Verletzungen und Beschädigung des Chassis zu vermeiden, sollten Sie das Chassis nicht an den Henkeln auf den Elementen (wie z.B. Stromanschlüsse, Kühlungen oder Karten) heben oder kippen; diese Henkel sind nicht dazu eingerichtet, das Gewicht der Einheit zu halten. Heben Sie das Chassis nur unter Verwendung von Griffen, die integraler Bestandteil des Chassis sind, oder indem Sie es unterhalb der Unterkante packen.

Avvertenza

Onde evitare il rischio di lesioni personali o danni al chassis, non tentare mai di sollevare o inclinare il chassis usando le maniglie dei vari moduli (alimentazioni, ventole o schede); tali maniglie infatti non supportano tutto il peso dell'unità. Sollevare l'unità servendosi eclusivamente delle apposite maniglie del chassis o prendendo il chassis da sotto la sua estremità inferiore.

Advarsel

Unngå personskade eller skade på kabinettet. Prøv aldri å løfte eller vippe kabinettet etter håndtakene på modulene (som f.eks. strømforsyninger, vifter eller kort). Disse håndtakene er ikke beregnet på å tåle vekten av enheten. Løft bare enheten etter håndtakene som er en del av kabinettet, eller ved å ta tak under den nederste kanten på kabinettet.

Aviso

Para evitar lesões pessoais ou danos ao chassis, nunca tente levantar ou inclinar o chassis utilizando as asas nos módulos (tais como fontes abastecedoras de energia, ventiladores, ou placas); estes tipos de asas não são concebidas para sustentar o peso da unidade. Levante a unidade utilizando apenas as asas que fazem parte integral do chassis, ou agarre o chassis por debaixo da sua borda inferior.

¡Advertencia!

Para prevenir cualquier tipo de lesión o dañar el chasis, no intente nunca levantar o ladear el chasis usando las manillas en los módulos (tales como fuentes de energía, ventiladores o tarjetas); estos tipos de manillas no fueron diseñadas para aguantar el peso de la unidad. Levante la unidad solamente usando las manillas que forman parte integral del chasis, o agarrando el chasis por debajo de su canto inferior.

Varning!

För att förhindra personskada eller skada på chassit får du aldrig försöka att lyfta eller luta chassit med användning av modulhandtag (t ex tillbehör, fläktar eller kort); sådana handtag är inte avsedda att bära upp enhetens vikt. Lyft enheten endast med användning av handtag som utgör en del av chassit, eller genom att gripa i chassit under dess nedre kant.



Statement 164—Two Person Lifting Requirement

Warning


Two people are required to lift the chassis. To prevent injury, keep your back straight and lift with your legs, not your back.

Waarschuwing

Er zijn twee personen nodig om het chassis op te tillen. Om letsel te voorkomen dient u uw rug recht te houden en met uw benen te tillen in plaats van met uw rug.

Varoitus

Asennuspohjan nostamiseen tarvitaan kaksi henkilöä. Nosta jalkojen (ei selän) avulla pitäen selkäsi suorana, jotta välttäisit loukkaantumista.

Attention

Le châssis doit être soulevé par au minimum deux personnes. Pour éviter tout risque d'accident, maintenez le dos droit et poussez sur vos jambes. Ne soulevez pas l'unité avec votre dos.

Warnung

Um das Chassis anzuheben, sind zwei Leute erforderlich. Um Verletzungsgefahr auszuschalten, halten Sie den Rücken gerade und heben Sie mit den Beinen, nicht dem Rücken.

Avvertenza

Per sollevare il chassis occorre l'intervento di due persone. Onde evitare il rischio di lesioni personali, tenere sempre ben dritta la schiena e piegare solo le gambe durante il sollevamento in modo da scaricare il peso sulle gambe e non sulla schiena.

Advarsel

Det er nødvendig at to personer løfter kabinettet. Hold ryggen rett og løft med beina - ikke ryggen - for å unngå personskade.

Aviso

São necessárias duas pessoas para levantar o chassis. Para evitar lesões, mantenha as costas direitas e levante o peso com ambas as pernas, sem forçar as costas.

¡Advertencia!

Se requieren dos personas para elevar el chasis. Para evitar lesiones, mantenga su espalda en posición recta y levante con sus piernas, no con su espalda.

Varning!

Det krävs två personer för att lyfta chassit. För att undvika skador ska du hålla ryggen rak och lyfta med benen, inte ryggen.



Statement 188—AC Power Supply Warning

Warning The AC power supply for the Cisco 7204 ,Cisco 7206, and Cisco 7200 VXR has double pole/neutral fusing.

Waarschuwing

De wisselstroom voeding voor de Cisco 7204 en Cisco 7206 heeft tweepolige/neutrale zekeringen.

Varoitus

Cisco 7204:n ja Cisco 7206:n vaihtovirtalähteessä on kaksinapainen/nollajohtimellinen liitäntä.

Attention

L'alimentation en courant alternatif du Cisco 7204 et du Cisco 7206 est munie de doubles fusibles pôle/neutre.

Warnung

Das Wechselstrom-Netzgerät für den Cisco 7204 und Cisco 7206 ist mit zweipoliger/neutraler Sicherung ausgestattet.

Avvertenza

L'alimentatore CA per il Cisco 7204 ed il Cisco Cisco 7206 èdotato di fusibili a polo doppio/neutro.

Advarsel

Vekselstrømsforsyningsenheten for Cisco 7204 og Cisco 7206 har både topolede og nøytrale sikringer.

Aviso

O fornecimento de corrente alternada ao Cisco 7204 e ao o Cisco 7206 possui fusão bipolar/neutra.

¡Advertencia!

La fuente de alimentación de corriente alterna (CA) para los equipos Cisco 7204 y Cisco 7206 posee doble fusible, para el polo activo y el neutro.

Varning!

Strömförsörjningsenheten för växelström för Cisco 7204 och Cisco 7206 har dubbel pol-/neutralsäkring.


Statement 200—Safety Information Referral Warning

Warning Before you install, operate, or service the system, read the Site Preparation and Safety Guide. This guide contains important safety information you should know before working with the system.

Waarschuwing

Lees de handleiding Voorbereiding en veiligheid van de locatie Handleiding voordat u het systeem installeert of gebruikt of voordat u onderhoud aan het systeem uitvoert. Deze handleiding bevat belangrijke beveiligingsvoorschriften waarvan u op de hoogte moet zijn voordat u met het systeem gaat werken.

Varoitus

Ennen kuin asennat järjestelmän tai käytät tai huollat sitä, lue Asennuspaikan valmistelu-jaturvaopas -opasta. Tässä oppaassa on tärkeitä turvallisuustietoja, jotka tulisi tietää ennen järjestelmän käyttämistä.

Attention

Avant d'installer le système, de l'utiliser ou d'assurer son entretien, veuillez lire le Guide de sécurité et de préparation du site. Celui-ci présente des informations importantes relatives à la sécurité, dont vous devriez prendre connaissance.

Warnung

Warnhinweis Bevor Sie das System installieren, in Betrieb setzen oder warten, lesen Sie die Anleitung zur Standortvorbereitung und Sicherheitshinweise. Dieses Handbuch enthält wichtige Informationen zur Sicherheit, mit denen Sie sich vor dem Verwenden des Systems vertraut machen sollten.

Avvertenza

Prima di installare, mettere in funzione o effettuare interventi di manutenzione sul sistema, leggere le informazioni contenute nella documentazione sulla Guida alla sicurezza. Tale guida contiene importanti informazioni che è necessario acquisire prima di iniziare qualsiasi intervento sul sistema.

Advarsel

Før du installerer, tar i bruk eller utfører vedlikehold på systemet, må du lese Veiledning for stedsklargjøring og sikkerhet. Denne håndboken inneholder viktig informasjon om sikkerhet som du bør være kjent med før du begynner å arbeide med systemet.

Aviso

Antes de instalar, funcionar com, ou prestar assistência ao sistema, leia o Guia de Preparação e Segurança do Local. Este guia contém informações de segurança importantes que deve conhecer antes de trabalhar com o sistema.

¡Advertencia!

Antes de instalar, manejar o arreglar el sistema, le aconsejamos que consulte la Guía de prevención y preparación de una instalación. Esta guía contiene importante información para su seguridad que debe saber antes de comenzar a trabajar con el sistema.

Varning!

Innan du installerar, använder eller utför service på systemet ska du läsa Förberedelser och säkerhet Handbok. Denna handbok innehåller viktig säkerhetsinformation som du bör känna till innan du arbetar med systemet.


Statement 202—Ground Connection Warning

Warning When installing the unit, the ground connection must always be made first and disconnected last.

Waarschuwing

Bij de installatie van het toestel moet de aardverbinding altijd het eerste worden gemaakt en het laatste worden losgemaakt.

Varoitus

Laitetta asennettaessa on maahan yhdistäminen aina tehtävä ensiksi ja maadoituksen irti kytkeminen viimeiseksi.

Attention

Lors de l'installation de l'appareil, la mise à la terre doit toujours être connectée en premier et déconnectée en dernier.

Warnung

Der Erdanschluß muß bei der Installation der Einheit immer zuerst hergestellt und zuletzt abgetrennt werden.

Avvertenza

In fase di installazione dell'unità, eseguire sempre per primo il collegamento a massa e disconnetterlo per ultimo.

Advarsel

Når enheten installeres, må jordledningen alltid tilkobles først og frakobles sist.

Aviso

Ao instalar a unidade, a ligação à terra deverá ser sempre a primeira a ser ligada, e a última a ser desligada.

¡Advertencia!

Al instalar el equipo, conectar la tierra la primera y desconectarla la última.

Varning!

Vid installation av enheten måste jordledningen alltid anslutas först och kopplas bort sist.


Statement 212—Unit Connection Warning

Warning


To be installed and maintained by service personnel as defined by AS/NZS 60950. Incorrect connection of this or connected equipment to a General Purpose Outlet could result in a hazardous situation. The telecommunication lines must be disconnected before unplugging the main power connection and while the housing is open.

Waarschuwing

Installatie en onderhoud mag alleen worden uitgevoerd door servicepersoneel zoals gedefinieerd in AS/NZS 60950. Als de apparatuur of de daarmee verbonden apparaten niet correct worden aangesloten op een geaard stopcontact, kan dit leiden tot een potentieel gevaarlijke situatie. Kabels voor telecommunicatie moeten worden losgekoppeld voordat de hoofdstekker uit het stopcontact wordt gehaald en als de behuizing is geopend.

Varoitus

Huoltohenkilökunnan asennettava ja huollettava AS/NZS 60950:n mukaisesti. Tämän tai liitetyn laitteiston virheellinen liitäntä pistorasiaan voi aiheuttaa vaaratilanteen. Tietoliikennelinjat on kytkettävä irti ennen päävirtaliitäntää ja kun kotelo on auki.

Attention

L'installation et l'entretien doivent être exécutés par un électricien qualifié (AS/NZS 60950. Une mauvaise connexion ou une connexion à une prise ordinaire présente un risque d'accident électrique. Il importe que les lignes de télécommunication soient déconnectées et le boîtier ouvert avant de débrancher la source d'alimentation principale.

Warnung

Installation und Instandhaltung durch Wartungspersonal, wie durch AS/NZS 60950 definiert. Unsachgemäßes Anschließen dieser oder verbundener Geräte an eine Universalsteckdose stellt eine potentielle Gefahrenquelle dar. Die Telekommunikationsleitungen müssen getrennt werden, bevor die Hauptstromverbindung ausgesteckt wird und während das Gehäuse offen ist.

Avvertenza

Installazione da effettuarsi solamente da parte del personale addetto in base alle norme AS/NZS 60950. Il collegamento inadeguato di questo dispositivo o il collegamento dello stesso ad una presa generica può provocare situazioni di rischio. È necessario scollegare le linee per le telecomunicazioni prima di togliere l'alimentazione di corrente a dispositivo aperto.

Advarsel

Må installeres og vedlikeholdes av servicepersonell slik AS/NZS 60950 definerer. Feil tilkobling av denne eller tilkoblet utstyr til et vanlig strømuttak kan føre til en farlig situasjon. Telelinjene må frakobles før strømforsyningen og mens kabinettet er åpent.

Aviso

Para ser instalado e mantido pelo pessoal técnico, tal como definido pela AS/NZS 60950. A ligação incorrecta deste equipamento ou de outro equipamento ligado a uma tomada multi-usos pode ter como resultado uma situação perigosa. As linhas de telecomunicações devem ser desligadas antes de ser desactivada a ligação da corrente de alimentação e enquanto o invólucro estiver aberto.

¡Advertencia!

La instalación y el mantenimiento debe realizarlos el personal de servicio, según lo dispuesto en la norma AS/NZS 60950. La conexión incorrecta de este equipo a un enchufe de uso general puede dar lugar a situaciones de peligro. Las líneas de telecomunicación deben estar desconectadas antes de desenchufar la toma de corriente principal mientras la carcasa esté abierta.

Varning!

Måste installeras och underhållas av servicepersonal i enlighet med AS/NZS 60950. Felaktig anslutning av denna eller tillhörande utrustning till ett växelströmsuttag kan resultera i en farlig situation. Telekommunikationslinjer måste frånkopplas innan det skyddsjordade kontaktdonet dras ur och medan höljet är öppet.



Statement 322—DC Power Off Warning

Warning


Before performing any of the following procedures, ensure that power is removed from the DC circuits. To ensure that all power is removed, locate the circuit breakers or fuses on the DC power lines that service the DC circuits. Turn OFF the DC power line circuit breakers and remove the DC power line fuses.

Waarschuwing

Zorg dat de stroom van de gelijkstroomcircuits is verwijderd voordat u een van de volgende procedures verricht. Zoek naar de stroomonderbrekers of zekeringen op de wisselstroomleidingen die stroom leveren naar de gelijkstroomcircuits om te zorgen dat alle stroom verwijderd is. Zet de stroomonderbrekers van de gelijkstroomleiding UIT en verwijder de zekeringen van de gelijkstroomleiding.

Varoitus

Ennen kuin suoritat mitään seuraavista toimenpiteistä, varmista, ettei tasasähköpiireissä ole virtaa. Varmista virrattomuus etsimällä tasasähköpiireihin tulevissa tasasähkölinjoissa olevat virrankatkaisimet tai sulakkeet. Käännä tasasähkölinjan virrankatkaisimet POIS PÄÄLTÄ ja irrota tasasähkölinjan sulakkeet.

Attention

Avant d'effectuer l'une des procédures suivantes, veillez à interrompre l'alimentation électrique des circuits de cc. Pour vérifier que tout le courant est bien désactivé, identifiez les coupe-circuits ou fusibles des lignes d'alimentation en cc qui desservent les circuits cc. Désactivez (position OFF) les coupe-circuits de la ligne d'alimentation en cc, puis retirez les fusibles de la ligne d'alimentation en cc.

Warnung

Stellen Sie sicher, dass an den Gleichstromkreisen kein Strom anliegt, bevor Sie einen der folgenden Vorgänge durchführen. Ermitteln Sie die Schutzschalter oder Sicherungen an den Gleichstromleitungen, die die Gleichstromkreise beliefern, um sicherzugehen, dass kein Strom mehr anliegt. Schalten Sie die Schutzschalter der Gleichstromleitungen AUS, und entfernen Sie die Sicherungen aus der Gleichstromleitung.

Avvertenza

Prima di eseguire una delle procedure seguenti, assicurarsi di aver disattivato l'alimentazione dei circuiti CC. A questo scopo, individuare gli interruttori automatici o i fusibili sulle linee di alimentazione CC che alimentano i circuiti CC. Disattivare gli interruttori automatici e rimuovere i fusibili delle linee di alimentazione CC.

Advarsel

Før du foretar noen av følgende prosedyrer må du påse at strømmen er fjernet fra likestrømkretsene. For å være sikkert på at all strøm er fjernet, finn vernebryterne eller sikringene på likestrømlinjene som går til likestrømkretsene. Slå AV vernebryteren for likestrømlinjen og fjern linjesikringene for likestrøm.

Aviso

Antes de executar qualquer dos procedimentos a seguir, assegure que a energia esteja removida dos circuitos CC. Para assegurar que toda a energia está removida, localize os disjuntores ou fusíveis nas linhas de energia CC que servem os circuitos CC. DESLIGUE os disjuntores da linha de energia CC e remova os fusíveis dessa linha.

¡Advertencia!

Antes de llevar a cabo cualquiera de los siguientes procedimientos, asegúrese de que los circuitos de CC no reciban alimentación eléctrica. Para estar seguro de que se ha retirado toda la alimentación eléctrica, localice los disyuntores o fusibles de las líneas de CC que alimentan los circuitos de CC. Coloque los disyuntores de la línea de alimentación de CC en posición de apagado (OFF) y retire los fusibles de la línea de alimentación de CC.

Varning!

Innan någon av följande åtgärder utförs ska man se till att strömmen är bortkopplad från likströmskretsarna. För att se till att all ström är bortkopplad, leta reda på brytarna eller säkringarna på likströmskablarna som leder till likströmskretsarna. Slå AV likströmsledningens brytare och ta bort likströmsledningens säkringar.



Statement 1001—Work During Lightning Activity

Warning


Do not work on the system or connect or disconnect cables during periods of lightning activity.

Waarschuwing

Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.

Varoitus

Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.

Attention

Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.

Warnung

Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.

Avvertenza

Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.

Advarsel

Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.

Aviso

Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).

¡Advertencia!

No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera.

Varning!

Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.

 



Statement 1003—DC Power Disconnection

Warning


Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Waarschuwing

Voordat u een van de onderstaande procedures uitvoert, dient u te controleren of de stroom naar het gelijkstroom circuit uitgeschakeld is.

Varoitus

Varmista, että tasavirtapiirissä ei ole virtaa ennen seuraavien toimenpiteiden suorittamista.

Attention

Avant de pratiquer l'une quelconque des procédures ci-dessous, vérifier que le circuit en courant continu n'est plus sous tension.

Warnung

Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß die Gleichstromschaltung keinen Strom erhält.

Avvertenza

Prima di svolgere una qualsiasi delle procedure seguenti, verificare che il circuito CC non sia alimentato.

Advarsel

Før noen av disse prosedyrene utføres, kontroller at strømmen er frakoblet likestrømkretsen.

Aviso

Antes de executar um dos seguintes procedimentos, certifique-se que desligou a fonte de alimentação de energia do circuito de corrente contínua.

¡Advertencia!

Antes de proceder con los siguientes pasos, comprobar que la alimentación del circuito de corriente continua (CC) esté cortada (OFF).

Varning!

Innan du utför någon av följande procedurer måste du kontrollera att strömförsörjningen till likströmskretsen är bruten.

Aviso

Antes de executar qualquer um dos procedimentos a seguir, verifique se a energia foi removida do circuito DC.

Advarsel

Før du udfører nogen af følgende procedurer, skal du sikre dig, at der ikke er strøm til jævnstrømskredsløbet.

 



Statement 1005—Circuit Breaker

Warning


This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 20A U.S. (240 VAC, 10A international)

Waarschuwing

Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan:
120 VAC, 20A U.S. (240 VAC, 10A international) is.

Varoitus

Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli:
120 VAC, 20A U.S. (240 VAC, 10A international)

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à :
120 VAC, 20A U.S. (240 VAC, 10A international)

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als:
120 VAC, 20A U.S. (240 VAC, 10A international) beträgt.

Avvertenza

Questo prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a:
120 VAC, 20A U.S. (240 VAC, 10A international)

Advarsel

Dette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse. Påse at verneenheten ikke er merket høyere enn:
120 VAC, 20A U.S. (240 VAC, 10A international)

Aviso

Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a:
120 VAC, 20A U.S. (240 VAC, 10A international)

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a:
120 VAC, 20A U.S. (240 VAC, 10A international)

Varning!

Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd). Kontrollera att skyddsanordningen inte har högre märkvärde än:
120 VAC, 20A U.S. (240 VAC, 10A international)

120 VAC, 20A U.S. (240 VAC, 10A international)

120 VAC, 20A U.S. (240 VAC, 10A international)

120 VAC, 20A U.S. (240 VAC, 10A international)

120 VAC, 20A U.S. (240 VAC, 10A international)



Statement 1008—Class 1 Laser Product

Warning


Class 1 laser product.

Waarschuwing

Klasse-1 laser produkt.

Varoitus

Luokan 1 lasertuote.

Attention

Produit laser de classe 1.

Warnung

Laserprodukt der Klasse 1.

Avvertenza

Prodotto laser di Classe 1.

Advarsel

Laserprodukt av klasse 1.

Aviso

Produto laser de classe 1.

¡Advertencia!

Producto láser Clase I.

Varning!

Laserprodukt av klass 1.

Aviso

Produto a laser de classe 1.

Advarsel

Klasse 1 laserprodukt.

 



Statement 1021—SELV Circuit

Warning


To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Waarschuwing

Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45 connectors. Ga voorzichtig te werk wanneer u kabels verbindt.

Varoitus

Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä (TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.

Attention

Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.

Warnung

Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise) nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln.

Avvertenza

Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione quando si collegano cavi.

Advarsel

Unngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du kobler kabler.

Aviso

Para evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado ao conectar os cabos.

¡Advertencia!

Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage = TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al conectar los cables.

Varning!

För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning (SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar.

 



Statement 1024—Ground Conductor

Warning


This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Waarschuwing

Deze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden gesteld en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is.

Varoitus

Laitteiden on oltava maadoitettuja. Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein asennettua maajohdinta. Ota yhteys sähkötarkastusviranomaiseen tai sähköasentajaan, jos olet epävarma maadoituksen sopivuudesta.

Attention

Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute sur la mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la sécurité électrique ou à un électricien.

Warnung

Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige Inspektionsbehörde oder einen Elektriker.

Avvertenza

Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si è certi della disponibilità di un adeguato collegamento di messa a terra, richiedere un controllo elettrico presso le autorità competenti o rivolgersi a un elettricista.

Advarsel

Dette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er usikker på om det finnes velegnet jordning.

Aviso

Este equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem um aterramento adequadamente instalado. Em caso de dúvida com relação ao sistema de aterramento disponível, entre em contato com os serviços locais de inspeção elétrica ou um eletricista qualificado.

¡Advertencia!

Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el equipo si no hay un conductor de tierra instalado correctamente. Póngase en contacto con la autoridad correspondiente de inspección eléctrica o con un electricista si no está seguro de que haya una conexión a tierra adecuada.

Varning!

Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.

 



Statement 1027—Class 1 LED Product

Warning


Class 1 LED product.

Waarschuwing

Klasse 1 LED-product

Varoitus

Luokan 1 valodiodituote

Attention

Alarme de produit LED Class I

Warnung

Class 1 LED-Produktwarnung

Avvertenza

Avvertenza prodotto LED di Classe 1

Advarsel

LED-produkt i klasse 1

Aviso

Produto de classe 1 com LED

¡Advertencia!

Aviso sobre producto LED de Clase 1

Varning!

Lysdiodprodukt av klass 1

 



Statement 1028—More Than One Power Supply

Warning


This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

Waarschuwing

Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen ontkoppeld te worden om de eenheid te ontkrachten.

Varoitus

Tässä laitteessa voi olla useampia kuin yksi virtakytkentä. Kaikki liitännät on irrotettava, jotta jännite poistetaan laitteesta.

Attention

Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées.

Warnung

Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein Strom zugeführt wird, müssen alle Verbindungen entfernt werden.

Avvertenza

Questa unità può avere più di una connessione all'alimentazione elettrica. Tutte le connessioni devono essere staccate per togliere la corrente dall'unità.

Advarsel

Denne enheten kan ha mer enn én strømtilførselskobling. Alle koblinger må fjernes fra enheten for å utkoble all strøm.

Aviso

Esta unidade poderá ter mais de uma conexão de fonte de energia. Todas as conexões devem ser removidas para desligar a unidade.

¡Advertencia!

Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar por completo el suministro de energía, deben desconectarse todas las conexiones.

Varning!

Denna enhet har eventuellt mer än en strömförsörjningsanslutning. Alla anslutningar måste tas bort för att göra enheten strömlös.

Aviso

Esta unidade pode ter mais de uma conexão de fonte de alimentação. Todas as conexões devem ser removidas para interromper a alimentação da unidade.

Advarsel

Denne enhed har muligvis mere end en strømforsyningstilslutning. Alle tilslutninger skal fjernes for at aflade strømmen fra enheden.

 



Statement 1030—Equipment Installation

Warning


Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel.

Varoitus

Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkilökunta.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés.

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden.

Avvertenza

Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale competente.

Advarsel

Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette utstyret.

Aviso

Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revisão deste equipamento.

¡Advertencia!

Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.

Varning!

Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera denna utrustning.

Aviso

Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento.

Advarsel

Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.

 



Statement 1040—Product Disposal

Warning


Ultimate disposal of this product should be handled according to all national laws and regulations.

Waarschuwing

Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.

Varoitus

Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.

Avvertenza

Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.

Advarsel

Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser.

Aviso

Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.

Varning!

Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.

Aviso

O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais.

Advarsel

Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.

 



Statement 1046—Installing or Replacing the Unit

Warning


When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Waarschuwing

Bij installatie of vervanging van het toestel moet de aardverbinding altijd het eerste worden gemaakt en het laatste worden losgemaakt.

Varoitus

Laitetta asennettaessa tai korvattaessa on maahan yhdistäminen aina tehtävä ensiksi ja maadoituksen irti kytkeminen viimeiseksi.

Attention

Lors de l'installation ou du remplacement de l'appareil, la mise à la terre doit toujours être connectée en premier et déconnectée en dernier.

Warnung

Der Erdanschluß muß bei der Installation oder beim Austauschen der Einheit immer zuerst hergestellt und zuletzt abgetrennt werden.

Avvertenza

In fase di installazione o sostituzione dell'unità, eseguire sempre per primo il collegamento a massa e disconnetterlo per ultimo.

Advarsel

Når enheten installeres eller byttes, må jordledningen alltid tilkobles først og frakobles sist.

Aviso

Ao instalar ou substituir a unidade, a ligação à terra deverá ser sempre a primeira a ser ligada, e a última a ser desligada.

¡Advertencia!

Al instalar o sustituir el equipo, conecte siempre la toma de tierra al principio y desconéctela al final.

Varning!

Vid installation eller utbyte av enheten måste jordledningen alltid anslutas först och kopplas bort sist.

Aviso

Ao instalar ou substituir a unidade, a conexão terra sempre deve ser executada primeiro e desconectada em seguida.

Advarsel

Ved installation og genmontering af enheden, skal jordforbindelsen altid installeres først og afinstalleres sidst.

 



Statement 1050—Power Module

Warning


Never install an AC power module and a DC power module in the same chassis.

Waarschuwing

Een voedingsmodule met wisselstroom mag nooit samen met een gelijkstroomvoedingsmodule in het chassis geïnstalleerd worden.

Varoitus

Älä koskaan asenna vaihtosähkötehomoduulia ja tasasähkötehomoduulia samaan asennuspohjaan.

Attention

N'installez jamais un module d'alimentation AC et un module d'alimentation DC dans le même châssis.

Warnung

Ein Wechelstromsmodul und ein Gleichstrommodul dürfen niemals in demselben Chassis installiert werden.

Avvertenza

Non installare un modulo di alimentazione in corrente alternata e un modulo di alimentazione in corrente continua nello stesso chassis.

Advarsel

En vekselstrømmodul og en likestrømmodul må aldri installeres i samme chassis.

Aviso

Nunca instale um modulo de corrente CA (corrente alternada) e um modulo CC (corrente contínua) no mesmo chassis.

¡Advertencia!

Nunca instale un módulo de potencia de corriente alterna (CA) en un módulo de potencia de corriente continua (CC) en el mismo chasis.

Varning!

Installera aldrig en växelströms- och en likströmskraftenhet i samma chassi.

 



Statement 1051—Laser Radiation

Warning


Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.

Waarschuwing

Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze glasvezels of aansluitingen.

Varoitus

Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso niitä suoraan optisilla välineillä.

Attention

Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil. Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments optiques.

Warnung

Unterbrochene Fasern oder Steckerverbindungenkönnen unsichtbare Laserstrahlung abgeben. Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.

Avvertenza

Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici.

Advarsel

Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte inn i strålene eller se på dem direkte gjennom et optisk instrument.

Aviso

Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe diretamente para os feixes ou com instrumentos ópticos.

¡Advertencia!

Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los rayos ni examine éstos con instrumentos ópticos.

Varning!

Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i strålar och titta aldrig direkt på dem med hjälp av optiska instrument.

Aviso

Radiação laser invisível pode ser emitida a partir de fibras ou conectores desconectados. Não fixe o olhar nos feixes e nem olhe diretamente com instrumentos ópticos.

Advarsel

Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte med optiske instrumenter.

 



Statement 1071—Warning Definition

Warning


IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

 



Statement 1074—Comply with Local and National Electrical Codes

Warning


Installation of the equipment must comply with local and national electrical codes.

Waarschuwing

Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.

Varoitus

Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti.

Attention

L'équipement doit être installé conformément aux normes électriques nationales et locales.

Warnung

Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

Avvertenza

L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.

Advarsel

Installasjon av utstyret må samsvare med lokale og nasjonale elektrisitetsforskrifter.

Aviso

A instalação do equipamento tem de estar em conformidade com os códigos eléctricos locais e nacionais.

¡Advertencia!

La instalación del equipo debe cumplir con las normativas de electricidad locales y nacionales.

Varning!

Installation av utrustningen måste ske i enlighet med gällande elinstallationsföreskrifter.

 



Japanese Electric Appliance and Radio Laws

Statement 371—Power Cable and AC Adapter

European Directives

This section includes the Telecom directives for the European Community:

Statement 275— Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as Amended by Directive 93/68/EEC

Statement 287—Declaration of Conformity to R&TTE Directives for the European Community, Swiutzerland, Norway, Iceland and Liechtenstein 1999/5/EC.

Statement 275—Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as Amended by Directive 93/68/EEC

For specifics about which standards have been applied, refer to the Declaration of Conformity.

English:

This equipment is in compliance with the essential requirements and other provisions of Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC.

Dansk:

Dette udstyr er i overensstemmelse med de ufravigelige hensyn og andre bestemmelser i direktiv 73/23/EEC og 89/336/EEC som ændred i direktiv 93/68/EEC.

Deutsch:

Dieses Gerät entspricht den wesentlichen Anforderungen und weiteren Bestimmungen der Richtlinien 73/23/EWG und 89/336/EWG mit der Ergänzung durch Richtlinie 93/68/EWG.

Español:

Este equipo cumple con los requisitos esenciales y otras disposiciones de las Directrices 73/23/EEC y 89/336/EEC de acuerdo a las modificaciones de la Directriz 93/68/EEC.

Français:

Cet appareil remplit les principales conditions requises et autres dispositions des Directives 73/23/EEC et 89/336/EEC, modifiées par la Directive 93/68/EEC.

Íslenska:

Þessir búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipana 73/23/EBE og 89/336/EBE, með breytingum skv. tilskipun 93/68/EBE.

Italiano:

Questa apparecchiatura è conforme ai requisiti essenziali e altre disposizioni delle Direttive 73/23/EEC e 89/336/EEC modificate con la Direttiva 93/68/EEC.

Nederlands:

Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijnen 73/23/EEC en 89/336/EEC zoals gewijzigd door richtlijn 93/68/EEC.

Norsk:

Dette utstyret samsvarer med de vesentligste kravene og andre regler i direktivene 73/23/EEC og 89/336/EEC samt i tilleggsdirektiv 93/68/EEC.

Português:

Este equipamento satisfaz os requisitos essenciais e outras provisões das Directivas 73/23/EEC e 89/336/EEC, conforme amendados pela Directiva 93/68/EEC.

[Product_Name]

Suomalainen:

Tämä laite on direktiivien 73/23/ETY ja 89/336/ETY (kuten muutettu direktiivissä 93/68/ETY) keskeisten vaatimusten ja määräysten mukainen.

Svenska:

Denna utrustning uppfyller de väsentliga kraven och andra villkor i direktiven 73/23/EEC och 89/336/EEC enligt ändringarna i direktiv 93/68/EEC.


Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein

English:

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

[Bulgarian]:    

[Czech]:   

Dansk
[Danish]:

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.

Deutsch
[German]:

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

Eesti
[Estonian]:    

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

Español
[Spanish]:

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.

[Greek]:  

Français
[French]:

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.

Íslenska
[Icelandic]:

Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.

Italiano
[Italian]:

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.

 

Latviski
[Latvian]:   

[Lithuanian]:    

Nederlands
[Dutch]:

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.

 

Malti
[Maltese]:    

 

Magyar
[Hungarian]:    

Norsk
[Norwegian]:

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.

 

Polski
[Polish]:    

Português
[Portuguese]:

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.

[Romanian]:    

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.

Slovensko
[Slovenian]:    

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Slovensky
[Slovak]:    

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.

 

Suomi
[Finnish]:    

 

 

Svenska
[Swedish]: 


You can check on the approval status of your product at the following URL:

http://tools.cisco.com/cse/prdapp/jsp/
externalsearch.do?action=externalsearch&page=EXTERNAL_SEARCH

California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)

The battery inside this product might contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchlorate-containing substances, see http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.

Regulatory Standards Compliance

This section includes Regulatory, Safety, EMC, Telecom, and NEBS standards. The Cisco 7200 series routers are in compliance with national and international standards as described in Table 1.

Table 1 Regulatory Compliance 

Regulatory Standards Compliance
Specification
Description
Safety

CAN/CSA-C22.2 No. 60950-1-03
EN 60950-1
IEC 60950-1
AS/NZS 60950.1
UL60950-1

EMC

FCC Part 15 (CFR 47) Class A

ICES-003 Class A

EN55022 Class A

CISPR22 Class A

AS/NZS CISPR 22 Class A

VCCI Class A

EN55024 Information Technology Equipment (Immunity)

EN50082-1/EN61000-6-1 Generic Immunity Standard

EN61000-3-2 Power Line Harmonics

EN61000-3-3 Voltage Fluctuations and Flicker

ETS/EN 300386 Telecommunications Network Equipment (EMC)

The following four EMC certification levels, while applying to other Cisco 7200 series routers, do not apply to the Cisco 7201 router

EN55022 Class B w/STP1

CISPR22 Class B w/STP1

AS/NZS CISPR Class B w/STP1

VCCI Class B with STP cables1

IP Phones

FCC Part 68 HAC
CS-03-HAC
AS/ACIF S004
AS/ACIF S040
NZ PTC 220 DR

Telecom (Cable Modem)

AS/ACIF S003:2001
IDA TS CM2

Telecom (Analog Modem)

AS/ACIF S002:2001
EIA/TIA-968-A
IC CS-03
HKTA 2011
PTC200
IDA TS PSTN1
PSTN01
CTR21 (98/482/EC)
Jate Blue Book

Telecom (Analog FXO)

AS/ACIF S002:2001
AS/ACIF S003:2001
EIA/TIA-968-A
IC CS-03
HKTA 2011
PTC200
IDA TS PSTN1
PSTN01
CTR21 (98/482/EC)
NET001/92
Jate Blue Book

Telecom (Analog FXS)

AS/ACIF S003:2001
EIA/TIA-968-A
IC CS-03
PTC200
Jate Blue Book

Telecom (Analog E&M)

AS/ACIF S003:2001
EIA/TIA-968-A
IC CS-03
PTC107
IDA TS PSTN1
CTR15 97/486/EC 1997
CTR17 97/487/EC 1997
Jate Blue Book

Telecom (Analog DID)

AS/ACIF S002:2001
AS/ACIF S003:2001
EIA/TIA-968-A
IC CS-03
IDA TS PSTN1
HKTA 2013
Jate Blue Book

Telecom (Serial—X.25)

CTR1 (97/544/EC)
CTR2 (97/545/EC)
Jate Green Book

Telecom (BRI)

EIA/TIA-968-A
IC CS-03
AS/ACIF S031:2001
CTR3 (98/515/EC)
CTR33 (98/521/EC)
HKTA 2014
IDA TS ISDN1 & 3
IS6100
Jate Green Book

Telecom (PRI)

EIA/TIA-968-A
IC CS-03
AS/ACIF S038:2001
CTR4 (98/520/EC)
CTR34 (98/518/EC)
HKTA 2015
IDA TS ISDN2
IS6100
Jate Green Book

Telecom (E1)

AS/ACIF S016:2001
CTR12 (97/520/EC)
CTR13 (97/521/EC)
TNA 117
IDA TS DCLN1
Jate Green Book

Telecom (T1)

EIA/TIA-968-A
IC CS-03
ID002
Jate Green Book

Telecom (E3)

AS/ACIF S016:2001
CTR24 (97/639/EC)

Telecom (Optical)

AS/ACIF S026:2001
IDA RS SDH1, 2 & 3
Jate Green Book

Telecom (DSL)

FCC Part 15.247 (CFR 47)
301-489-1
301-489-17
RSS-210
EN 300.328
ENG 132943
Std 33a
DGT LP0002
NOM-121
AS/NZS 4771

Radio
 

CDMA/GSM/UMTS systems

824-849 MHz
869-894 MHz

890-960 MHz

902-928 MHz

1710-1880 MHz

1850-1990 MHz

1910-1930 MHz

2110-2170 MHz

2.4 GHz 802.11 systems

47 CFR Part 2
47 CFR, Part (15.247)
47 CFR 15.249 (RFID)
RSS-210 Rev 6
RSS-Gen Rev 1
EN 300.328
Std 66
DGT LP0002
NOM-121 Rev 2.7
AS/NZS 4268
ETSI EN 300 440-1 V1.3.1
ETSI EN 300 328-1 V1.3.1

4.9 GHz Public Safety

5150-5350, 5470-5725 MHz 802.11 systems

47 CFR Part 15 (E)
RSS-210 Rev 6
RSS-GEN
DGT LP0002
EN 301.893
ITU-R Resolution 5/16
SP-5150 Rev 2
RSP-100 Rev 8
STD71
CNC Resolution 288-2
ANATEL Resolution 365
AS/NZS 4268 in the title, as in force from time to time
ETSI EN 300 440-1 V1.3.1
ETSI EN 300 328-1 V1.3.1

5725-5850 MHz systems

47 CFR, 2003 Part 15.247
RSS-210 Rev 6
RSS-GEN
NOM-121 Rev 2.7
CNC Resolution 288-2
ANATEL Resolution 365
AS/NZS 4268 in the title, as in force from time to time
ETSI EN 300 328-1 V1.3.1
ETSI EN 300 440-1 V1.3.1

1 CISPR22/EN55022 Class B, AS/NZS Class B, and VCCI Class B require the use of shielded twisted pair (STP) cables on copper I/O ports. Class A requires unshielded twisted pair (UTP) cables. These certification levels do not apply tothe Cisco 7201 router.


The Cisco 7201, 7202, Cisco 7204, Cisco 7206, Cisco 7204VXR, and Cisco 7206VXR are designed to meet the industry EMC, safety, and environmental standards described in Table 2. (Qualifications are complete or are in progress.)

Table 2 Industry EMC, Safety, and Environmental Standards

Specification
Description

NEBS1

GR-1089-CORE: EMC and Safety (NEBS Level 3)

GR-63-CORE: Physical Protection (NEBS Level 3)

SR-3580: NEBS Criteria Levels (Level 3)

ETSI2

ETS 300 019 Storage Class 1.1

ETS 300 019 Transportation Class 2.3

ETS 300 019 Stationary Use Class 3.1

ETS EN 300 386

1 NEBS = Network Equipment Building Systems

2 ETSI = European Telecommunications Standards Institute


Table 3 Cisco 7201 Industry, EMC, and Environmental Standards

Specification
Description

NEBS

Designed to meet GR-63-CORE NEBS Level 3
Designed to meet GR-1089-CORE NEBS Level 3

ETSI

Designed to meet ETS 300 019-1-1, Class 1.2 Storage
Designed to meet ETS 300 019-1-2, Class 2.3 Transportation
Designed to meet ETS 300 019-1-3, Class 3.2 Stationary Use


EMC Environmental Conditions for Products Installed in the European Union

This section applies to products to be installed in the European Union.

The equipment is intended to operate under the following environmental conditions with respect to EMC:

A separate defined location under user's control.

Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.

AC power distribution shall be one of the following types, where applicable: TN-S and TN-C as defined in IEC 364-3.

In addition, if equipment is operated in a domestic environment, interference may occur.

EMC Class A Statements/Warnings

This section includes the EMC Class A warnings for the Cisco 7201, 7202, Cisco 7204, Cisco 7206, Cisco 7204VXR, and Cisco 7206VXR. The following Class A warnings are included:

FCC Class A

Canada - Class A

Statement 191—VCCI Class A Warning for Japan

Statement 256—Class A Warning for Hungary

Statement 257—Class A Notice for Taiwan and Other Traditional Chinese Markets

Statement 294—Class A Warning for Korea

Statement 340—Class A Warning for CISPR22

FCC Class A

Modifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense.

Canada - Class A

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Statement 191—VCCI Class A Warning for Japan

Warning


This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

 



Statement 256—Class A Warning for Hungary

Warning


This equipment is a Class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used.

 



Statement 257—Class A Notice for Taiwan and Other Traditional Chinese Markets

Warning


This is a Class A Information Product, when used in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures.

 



Statement 294—Class A Warning for Korea

Warning


This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type.

 



Statement 340—Class A Warning for CISPR22

Warning


This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Waarschuwing

Dit is een product van klasse A. In een woonomgeving kan dit product radiostoring veroorzaken. In dat geval moet de gebruiker de juiste maatregelen nemen.

Varoitus

Tämä on A-luokan tuote. Kotona käytettynä tämä tuote voi aiheuttaa radiotaajuushäiriöitä, jolloin käyttäjän tulisi ryhtyä vaadittaviin toimenpiteisiin häiriöiden ehkäisemiseksi.

Attention

Il s'agit d'un produit de classe A. Dans un environnement local, ce produit peut entraîner des perturbations radioélectriques, auquel cas l'utilisateur devra éventuellement prendre des mesures adéquates.

Warnung

Dies ist ein Produkt der Klasse A. Bei der Verwendung dieses Produkts im Haus- oder Wohnungsbereich kann es zu Funkstörungen kommen. In diesem Fall muss der Benutzer u. U. angemessene Maßnahmen ergreifen.

Avvertenza

Prodotto di classe A. È possibile che il prodotto generi interferenze radio in un ambienti chiusi. In questo caso l'utente deve intraprendere le misure adeguate per risolvere il problema.

Advarsel

Dette er et produkt i klasse A. I et hjemmemiljø kan dette produktet forårsake radioforstyrrelser, og brukeren kan da være nødt til å ta de nødvendige forholdsregler.

Aviso

Este é um produto de classe A. Em um ambiente doméstico, este produto pode causar interferência de rádio. Nesse caso, talvez o usuário precise tomar as medidas adequadas.

¡Advertencia!

Este es un producto de clase A. En el ámbito doméstico, este producto puede causar radiointerferencias, lo que puede hacer necesaria la puesta en marcha de medidas adecuadas.

Varning!

Detta är en klass A-produkt. Denna produkt kan orsaka radiostörningar inomhus. Det kan då vara ett krav att användaren vidtar lämpliga åtgärder.

 



Network Equipment Building System (NEBS)

The Cisco 7200 Series Routers adhere to the following NEBS GR-1089-Core requirements:

To comply with GR-1089-Core Intra-building Lighting requirements, all 10Mbps, 100 Mbps, and 1000 Mbps copper Ethernet interfaces shall be connected with shielded cable with the shield grounded at each end of the cable.

To comply with GR-1089-Core grounding requirements, all Cisco 7200 Series Routers are provided with a provision to attach a two-hole ground lug that accepts a #6 AWG conductor. Refer to the specific router hardware installation and configuration guide for details of the grounding provision.

To comply with GR-1089-Core Bonding and Grounding documentation requirements, all Cisco 7200 Series Routers use the DC-I (DC-isolated) grounding architecture. The DC input return and frame ground are isolated from one another.

Grounding connectors shall be NRTL Listed.

The Cisco 7200 Series Routers can be installed in network telecommunications facilities.

The intra-building port(s) of the equipment or subassembly is suitable for connection to intra-building or unexposed wiring or cabling only. The intra-building port(s) of the equipment or subassembly must not be metallically connected to interfaces which connect to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE, Issue 4) and require isolation from the exposed OSP cabling. The addition of primary protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.

The Cisco 7200 Series Routers have AC power ports that are intended for deployments where an external Surge Protective Device (SPD) is utilized at the AC power service equipment (see definition in National Electric Code).

The Cisco 7200 Series Routers are designed for a Common Bonding Network (CBN) installation.

Telecom Approvals Listing

The Cisco 7201, 7202, Cisco 7204, Cisco 7206, Cisco 7204VXR, and Cisco 7206VXR meet the requirements listed in this section for telecommunications equipment.

FCC Part 68 Notice

The Cisco 7201, 7202, Cisco 7204, Cisco 7206, Cisco 7204VXR, and Cisco 7206VXR equipment complies with Part 68 of the FCC rules. A label on the bottom of the chassis contains the FCC registration number among other information. If requested, this information must be provided to the telephone company.

This equipment cannot be used on telephone company-provided coin services. Connection to the Party Line Service is subject to state tariffs.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify you as soon as possible. You will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that might affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.

If you experience trouble with this equipment, please contact Cisco for repair and warranty information. If the problem is causing harm to the telephone network, the telephone company might request that you remove the equipment from the network until the problem is resolved. All repairs should be handled by authorized Cisco Systems service personnel.

We recommend that you install an AC surge arrestor in the AC outlet to which this device is connected. This action will help to avoid damage to the equipment caused by local lightning strikes and other electrical surges.

This equipment uses the Uniform Service Order Code (USOC) jacks described in Table 4.

.

Table 4 USOC Jacks 

Model Name
Facility Interface Code
Service Order Code
Jack Type

PA-2CT1/PRI

04DU9-BN/DN/1KN/1SN/1ZN

6.0N

Use registered CSU

PA-4B-U

02IS5

6.0N

RJ-49C/CA-A11

PA-8B-S/T

02IS5

6.0N

RJ-48C/CB-1D

PA-A3-8T1IMA

04DU9-BN/DN/1KN/1SN/1ZN

6.0N/F

RJ-48C

PA-MC-2T1

04DU9-BN/DN/1KN/1SN/1ZN

6.0N/F

RJ-48C

PA-MC-4T1

04DU9-BN/DN/1KN/1SN/1ZN

6.0N/F

RJ-48C

PA-MC-8DSX1

04DU9-BN/DN/1KN/1SN/1ZN

6.0N/F

RJ-48C

PA-MC-8TE1+

04DU9-1SN

6. 0N

RJ-48C

PA-MC-8T1

04DU9-BN/DN/1KN/1SN/1ZN

6.0N/F

RJ-48C

PA-MCX-2TE1

04DU9-1SN

6.0Y

RJ-48C

PA-MCX-4TE1

04DU9-1SN

6.0Y

RJ-48C

PA-MCX-8TE1

04DU9-1SN

6.0Y

RJ-48C

PA-VXA-1TE1-24+

04DU9-BN/1KN/1SN

6.0Y

RJ-48C

PA-VXA-1TE1-30+

04DU9-BN/1KN/1SN

6.0Y

RJ-48C

PA-VXB-2TE1

04DU9-BN/1KN/1SN

6.0Y

RJ-48C

PA-VXB-2TE1+

04DU9-BN/1KN/1SN

6.0Y

RJ-48C

PA-VXC-2TE1

04DU9-BN/1KN/1SN

6.0Y

RJ-48C

PA-VXC-2TE1+

04DU9-BN/1KN/1SN

6.0Y

RJ-48C


Canada - CS-03 Certification

The Cisco 7201, 7202, Cisco 7204, Cisco 7206, Cisco 7204VXR and Cisco 7206VXR meet the requirements of the Industry Canada label (CS-03) for telecommunications equipment. Table 5 lists the CS-03 approval numbers for the equipment.

Table 5 CS-03 Approval 

Model Number
Approval Number

PA-2CT1/PRI

2461 7791 A

PA-4B-U

2461 8057A

PA-8B-S/T

2461 7920A

PA-A3-8T1IMA

2461 9914 A

PA-MC-2T1

2461 9227 A

PA-MC-4T1

2461 9227 A

PA-MC-8DSX1

2461 9227 A

PA-MC-8T1

2461 9227 A

PA-MC-8TE1+

2461 11246 A

PA-MCX-2TE1

2461 10722 A

PA-MCX-4TE1

2461 10722 A

PA-MCX-8TE1

2461 10722 A

PA-VXA-1TE1-24+

2461 10101 A

PA-VXA-1TE1-30+

2461 10101 A

PA-VXB-2TE1

2461 10101 A

PA-VXB-2TE1+

2461 10101 A

PA-VXC-2TE1

2461 10101 A

PA-VXC-2TE1+

2461 10101 A


Observe the following general information and safety precautions:

The industry Canada label identifies CS-03 certified equipment. This certification means that the equipment meets certain telecommunications network protection, operation, and safety requirements as described in the appropriate terminal equipment requirements documents. The department does not guarantee the equipment will operate to the user's satisfaction.

Before installing the equipment, check that you have permission to connect it to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or any equipment malfunctions, may cause the telecommunications company to request that the user disconnect the equipment.

Ensure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.


Warning Do not attempt to make such connections yourself. Contact the appropriate electric inspection authority or electrician as appropriate.


Japan - JATE Certification

The Cisco 7201, 7202, Cisco 7204, Cisco 7206, Cisco 7204VXR, and Cisco 7206VXR meet the requirements of the Japan Approvals Institute for Telecommunications Equipment (JATE). Table 6 lists the JATE approval details.

Table 6 JATE Approval 

Applicant
Model Number
Approval Number

Nihon Cisco Systems

PA-A2-4T1C-OC3SM

N97-K063-0

Nihon Cisco Systems

PA-A2-4T1C-T3ATM

N96-K063-0

Nihon Cisco Systems

PA-A3-8T1IMA

D99-0385JP

Nihon Cisco Systems

PA-A3-T3

N98-N324-0

Nihon Cisco Systems

PA-A3-OC3SMI

N98-3009-0

Nihon Cisco Systems

PA-A3-OC3SML

N98-3010-0

Nihon Cisco Systems

PA-A4-OC12SMI

L99-1292

Nihon Cisco Systems

PA-A6-OC3SMI

D02-0549JP

Nihon Cisco Systems

PA-A6-OC3SML

D02-0549JP

Nihon Cisco Systems

PA-A6-OC3MM

D02-0549JP

Nihon Cisco Systems

PA-2CT1/PRI

N97-K005-0

Nihon Cisco Systems

PA-CT3/4T1

N98-N060-0

Nihon Cisco Systems

PA-MC-2T3+

L99-1065

Nihon Cisco Systems

PA-MC-2T1

C99-0657JP,
L99-1159

Nihon Cisco Systems

PA-MC-4T1

T98-6318-0

Nihon Cisco Systems

PA-MC-8T1

T98-6317-0

Nihon Cisco Systems

PA-MC-8DSX1

T98-6317-0

Nihon Cisco Systems

PA-MC-8TE1+

CD00-0558JP, L00-0142

Nihon Cisco Systems

PA-MC-T3

N98-N325-0

Nihon Cisco Systems

PA-SRP-OC12SMI

L99-1291

Nihon Cisco Systems

PA-T3

N98-N325-0

Nihon Cisco Systems

PA-T3+

N98-N358-0

Nihon Cisco Systems

PA-2T3

N98-N326-0

Nihon Cisco Systems

PA-2T3+

N98-N359-0

Nihon Cisco Systems

PA-4T

N98-K058-0

Nihon Cisco Systems

PA-4T+

N97-K012-0

Nihon Cisco Systems

PA-8B-S/T

T97-5318-0

Nihon Cisco Systems

PA-8T-232

M96-N218-0

Nihon Cisco Systems

PA-8T-V35

N97-K064-0

Nihon Cisco Systems

PA-8T-X21

N96-N158-0

Nihon Cisco Systems

PA-MCX-2TE1

CD00-0556JP, L00-0140

Nihon Cisco Systems

PA-MCX-4TE1

CD00-0557JP, L00-0141

Nihon Cisco Systems

PA-MCX-8TE1

CD00-0558JP, L00-0142

Nihon Cisco Systems

PA-VXA-1TE1-24+

CD01-0783JP, L01-0254

Nihon Cisco Systems

PA-VXA-1TE1-30+

CD01-0783JP, L01-0254

Nihon Cisco Systems

PA-VXB-2TE1

CD00-0021JP, L00-0011

Nihon Cisco Systems

PA-VXB-2TE1+

CD00-0021JP, L00-0011

Nihon Cisco Systems

PA-VXC-2TE1

CD00-0021JP, L00-0011

Nihon Cisco Systems

PA-VXC-2TE1+

CD00-0021JP, L00-0011


Korea - RRL Certification

The following equipment meets the requirements of the Director General of Radio Research Lab (RRL) Ministry of Information and Communication (MIC), Republic of Korea. Refer to Table 7 for RRL approval details.

Table 7 Korea RRL Approval 

Model Number
Approval Number

Cisco 7206VXR

1-WD-USA-C31-99-0885

Cisco 7206VXR-CH

E-E011-01-4095 (A)

Cisco 7206VXR/400/2 FE

E-E011-01-4101 (A)

Cisco 7204VXR

T-C31-00-0182

Cisco 7204VXR/225

T-C31-01-1075

Cisco 7204VXR-CH

E-E011-01-4099(A)

Cisco 7201

Approval pending


Site Preparation and Safety Information


Note Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS 3260) should install, replace, or service the equipment. Install the system in accordance with the U.S. National Electric Code if you are in the United States.



Warning The instructions in this guide warn you about situations that could cause bodily injury. Before working on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.


Preparing Your Site for Installation

To ensure normal system operation, plan your site configuration and prepare your site before installation.

Choosing a Site for Installation

Install the system in a restricted access area, where access can be gained only by service personnel through the use of a special tool, lock and key, or other means of security.

Choose a site with a dry, clean, well-ventilated and air-conditioned area.

Choose a site that maintains an ambient temperature of 32 to 104oF (0 to 40oC).

Ensuring Overcurrent Protection

The system relies on the protective devices in the building installation for protection against short-circuit, overcurrent, and earth (grounding) fault. Ensure that the protective devices in the building installation are properly rated to protect the system, and that they comply with national and local codes.

Grounding the System

Do not defeat the ground conductor on an AC plug.

Connect AC-powered systems to grounded power outlets.

Connect the system to earth (ground).

Creating a Safe Environment

Keep tools and chassis components off the floor and away from foot traffic.

Clear the area of possible hazards, such as moist floors, ungrounded power extension cables, and missing safety grounds.

Keep the area around the chassis free from dust and foreign conductive material (such as metal flakes from nearby construction activity).

Rack-Mounting the System

A rack-mount kit and cable-management brackets come with the system. The kit is not suitable for racks with obstructions (such as a power strip) that could impair access to system components. Allow sufficient clearance around the rack for system maintenance.

Ensuring Proper Airflow

Install the system in an open rack whenever possible. If installation in an enclosed rack is unavoidable, ensure that the rack has adequate ventilation.

Maintain ambient airflow to ensure normal operation. If the airflow is blocked or restricted, or if the intake air is too warm, an overtemperature condition can occur.

Allow at least 6 inches (15.24 cm) of clearance around the ventilation openings of the chassis.

Avoid placing the system in an overly congested rack or directly next to another equipment rack. Heat exhaust from other equipment can enter the inlet air vents and cause an overtemperature condition.

Equipment near the bottom of a rack might generate excessive heat that is drawn upward and into the intake ports of the equipment above. The warm air can cause an overtemperature condition in the equipment above.

Ensure that cables from other equipment do not obstruct the airflow through the chassis or impair access to the power supplies or cards. Route cables away from field-replaceable components to avoid disconnecting cables unnecessarily for equipment maintenance or upgrades.

Stabilizing the System

Install any stabilizers that came with your equipment rack before mounting or servicing the system in the rack.

Load the rack from the bottom to the top, with the heaviest system at the bottom.

Do not stack the system on top of any other equipment. If the system falls, it can cause severe bodily injury and damage the equipment.

If you are using an equipment shelf, ensure that the shelf is constructed to support the weight and dimensions of the chassis.

If you are using a 2-post rack, ensure that the weight of the chassis does not make the rack unstable. Secure the 2-post rack with ceiling brackets if the rack is populated with heavy equipment.

Bolt the rack to the floor for stability.

Figure 1 Standard Equipment Rack Dimensions

Lifting the System

Figure 2 Safely Lifting the System

Disconnect all power and external cables before lifting the system.

Ensure that your footing is solid and the weight of the system is evenly distributed between your feet.

Lift the system slowly, keeping your back straight. Lift with your legs, not with your back. Bend at the knees, not at the waist.

Do not attempt to lift the system with the handles on the power supplies or on any of the cards. These handles are not designed to support the weight of the system.

Depending on the weight of the system, more than one person might be required to lift it.

Power Considerations

AC and DC power supplies, and an optional redundant (second) power supply, are available for most systems.


Note Refer to your hardware installation guide for AC and DC power specifications and for redundant power supply availability.


Be careful when connecting systems to the supply circuit so that wiring is not overloaded.

AC Power

The system is designed for connection to TN power systems. A TN power system is a power distribution system with one point connected directly to earth (ground). The exposed conductive parts of the installation are connected to that point by protective earth conductors.

Ensure that the plug-socket combination is accessible at all times, because it serves as the main disconnecting device.

DC Power

Connect DC-input power supplies only to a DC power source that complies with the safety extra-low voltage (SELV) requirements in the UL60950-1, CAN/CSA-C22.2 No. 60950-1-03, AS/NZS 60950-1
EN/IEC 60825-1, 21 CFR 1040, EN 60950-1, and IEC 60950-1 standards.

Incorporate a readily accessible two-poled disconnect device in the fixed wiring.

Ensure that power is removed from the DC circuit before installing or removing power supplies. Tape the switch handle of the DC circuit breaker in the off position.

Use only copper conductors to connect to a DC terminal block.

Use approved wiring terminations, such as closed-loop or spade-type with upturned lugs, when stranded wiring is required. These terminations should be the appropriate size for the wires and should clamp both the insulation and the conductor.

Ensure that no exposed portion of the DC-input power source wire extends from the terminal block plug. An exposed wire can conduct a harmful level of electricity.

Redundant Power

If your system includes an optional redundant (second) power supply, connect each of the two power supplies to different input power sources. Failure to do so makes the system susceptible to total power failure in the event that one of the power supplies fails.

Preventing ESD

Electrostatic discharge (ESD) damage occurs when electronic cards or components are mishandled and can result in complete or intermittent failures. Note the following guidelines before you install or service the system:

Always wear an ESD-preventive wrist or ankle strap when handling electronic components. Connect one end of the strap to an ESD jack or an unpainted metal component on the system (such as a captive installation screw).

Handle cards by the faceplates and edges only; avoid touching the printed circuit board and connector pins.

Place any removed component on an antistatic surface or in a static shielding bag.

Avoid contact between the cards and clothing. The wrist strap only protects the card from ESD voltages on the body; ESD voltages on clothing can still cause damage.


Note For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms (Mohms).


Installing and Servicing the System

Disconnect all power and external cables before installing the system.

Install the system in compliance with your local and national electrical codes:

United States: National Fire Protection Association (NFPA) 70; United States National Electrical Code.

Canada: Canadian Electrical Code, Part I, CSA C22.1.

Other countries: If local and national electrical codes are not available, refer to IEC 364, Part 1 through Part 7.

Do not work alone under potentially hazardous conditions.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Do not touch the backplane or midplane with your hand or metal tools.

Remove all jewelry (including rings and chains) or other items that could get caught in the system or heat up and cause serious burns.

Disconnecting Power

Locate the emergency power-off switch for the room before working with the system.

Turn off the power and disconnect the power from the circuit when working with components that are not hot-swappable or when working near the system backplane or midplane. If the system does not have an on/off switch, unplug the power cord.

To completely de-energize the system, disconnect the power connection to all power supplies.

For DC power supplies, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the off position, and tape the switch handle of the circuit breaker in the off position.

Do not touch the power supply when the power cord is connected. Line voltages are present within the power supply even when the power switch is off and the power cord is connected.

Working with WAN Interfaces

Use caution when installing or modifying telephone lines to prevent electric shock.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Do not touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Hazardous network voltages are present in WAN ports regardless of whether power to the system is off or on. When detaching cables, detach the end away from the system first.

Do not use a telephone (unless it is the cordless type) during an electrical storm.

Do not use a telephone to report a gas leak in the vicinity of the leak.

Do not install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Working with Lasers

Fiber-optic ports (for example, FDDI, OC-3, OC-12, OC-48, ATM, GBIC, and 100BaseFX) are considered Class 1 laser or Class 1 LED ports.

These products have been tested and found to comply with Class 1 limits of IEC 60825-1, IEC 60825-2, EN 60825-1, EN 60825-2, and 21CFR1040.

To avoid exposure to radiation, do not stare into the aperture of a fiber-optic port. Invisible radiation might be emitted from the aperture of the port when no fiber cable is connected.

Figure 3, Figure 4, and Figure 5 show examples of Class 1 laser and LED labels. The smaller labels shown in Figure 3and Figure 4 usually appear on field-replaceable cards. Or the larger label shown in Figure 5 appears on the chassis.

Figure 3 Class 1 Laser Label for a Single-Mode Fiber Port

Figure 4 Class 1 LED Label for a Multimode Fiber Port

Figure 5 Class 1 Laser Label for a Chassis

Preventing EMI

When you run wires for any significant distance in an electromagnetic field, electromagnetic interference (EMI) can occur between the field and the signals on the wires.

Note that:

Bad plant wiring can result in radio frequency interference (RFI).

Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers and receivers in the system, and can even create an electrical hazard by conducting power surges through lines and into the system.

To predict and remedy strong EMI, consult RFI experts.

Covering Empty Slots

Ensure that all cards, faceplates, and covers are in place. Blank faceplates and cover panels are used to:

Prevent exposure to hazardous voltages and currents inside the chassis

Help contain electromagnetic interference (EMI) that might disrupt other equipment

Direct the flow of cooling air through the chassis

Disposing of the System

Dispose of the system and its components (including batteries) as specified by all national laws and regulations.

Related Documentation

Your router and the Cisco IOS software running on it contain extensive features and functionality, which are documented in the following resources:

For hardware installation and maintenance information on Cisco 7200 series routers, refer to the following installation and configuration guides or the quick start guides.

Cisco 7200 VXR Installation and Configuration Guide at:
http://www.cisco.com/univercd/cc/td/doc/product/core/7200vx/72vxicg/index.htm

Cisco 7200 VXR Routers Quick Start Guide at:
http://www.cisco.com/en/US/products/hw/routers/ps341/products_quick_start09186a00801e5279.html

Cisco 7206 Installation and Configuration Guide at:
http://www.cisco.com/univercd/cc/td/doc/product/core/7206/7206ig/index.htm

Cisco 7206 Quick Start Guide at:
http://www.cisco.com/en/US/products/hw/routers/ps341/products_quick_start09186a00800a85fe.html

Cisco 7204 Installation and Configuration Guide at:
http://www.cisco.com/univercd/cc/td/doc/product/core/7204/7204ig/index.htm

Cisco 7202 Installation and Configuration Guide at:
http://www.cisco.com/univercd/cc/td/doc/product/core/7202/7202icg/index.htm

Cisco 7201 Installation and Configuraiton Guide at:
http://www.cisco.com/en/US/customer/products/hw/routers/ps341/products_installation_and_configuration_guide_book09186a00807f7036.html

Cisco 7201 Router Quick Start Guide at:
http://www.cisco.com/en/US/customer/products/hw/routers/ps341/prod_quick_installation_guide09186a00807f654c.html

For other documentation, see the following online master indexes for a listing of all documents related to the Cisco 7200 series routers:

Cisco 7200 Series Routers Documentation Roadmap at: http://www.cisco.com/en/US/products/hw/routers/ps341/products_documentation_roadmap09186a00801c0915.html

Cisco 7201 Documentation Roadmap at:
http://www.cisco.com/en/US/customer/products/hw/routers/ps341/products_documentation_roadmap09186a00807f635a.html

Cisco 7200 Series Routers Port Adapter Documentation Roadmap at: http://www.cisco.com/en/US/products/hw/routers/ps341/products_documentation_roadmap09186a00801c0a32.html

Cisco 7201 Port Adapter Documentation Roadmap at:
http://www.cisco.com/en/US/customer/products/hw/routers/ps341/products_documentation_roadmap09186a00807f704f.html

For troubleshooting information, see the following online master index:

Cisco 7200 Series Routers Troubleshooting Documentation Roadmap at: http://www.cisco.com/univercd/cc/td/doc/product/core/7200vx/ol3518.htm

Cisco 7201 Troubleshooting Documentation Roadmap at:
http://www.cisco.com/en/US/customer/products/hw/routers/ps341/prod_quick_installation_guide09186a00807f654c.html

For Cisco IOS software configuration information and support, refer to the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware. See http://www.cisco.com/en/US/products/sw/iosswrel/tsd_products_support_category_home.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.