Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
Appendix A - Technical Specifications
Downloads: The complete bookPDF (PDF - 12.89MB) | Feedback

Technical Specifications

Table Of Contents

Technical Specifications

Router Specifications


Technical Specifications


This appendix lists the Cisco 12010, Cisco 12410 and Cisco 12810 router specifications.

Router Specifications

The Cisco 12010, Cisco 12410, and Cisco 12810 series routers specifications are presented in four tables:

Table A-1, "Physical Specifications"

Table A-2, "AC Electrical Specifications"

Table A-3, "DC Electrical Specifications"

Table A-4, "Environmental Specifications"

Table A-1 Physical Specifications

Description
Value

Chassis height

37.5 in. (95.2 cm)

Chassis width

17.25 in. (43.8 cm)
19.0 in. (48.3 cm) including chassis rack-mount flanges and front door width

Chassis depth

22.0 in. (55.9 cm)
26.5 in (67.3 cm) including cable management system and front cover

Weight

chassis only

chassis: fully configured using all card slots and 2 AC input power supplies

125 lb (56.7 kg)

287 lb (130.2 kg)


Table A-2 AC Electrical Specifications

Description
Value

Power

2791 VA (volt-amps) per AC power supply
(2 AC power supplies per system)—original series

3000 VA (volt-amps) per AC power supply
(2 AC power supplies per system)—original series

Rated input voltage1

200-240 VAC nominal (range: 180 to 264 VAC)
220-240 VAC (UK)

Rated input line frequency1

50/60 Hz nominal (range: 47 to 63 Hz)
50/60 Hz UK

Input current rating1

15 A maximum @ 200 VAC
13 A maximum @220 to 240 VRMS (UK)

Source AC service requirement1

20 A North America; 16 A international; 13 A UK

Heat dissipation
(total maximum)

2800 W@9,544 BTU/hour

Redundancy

2 AC power supply modules required for 2N redundancy

1 For each AC power supply module.



Caution To ensure that the chassis configuration complies with the required power budgets, use the on-line power calculator. Failure to properly verify the configuration may result in an unpredictable state if one of the power units fails. Contact your local sales representative for assistance.

Table A-3 DC Electrical Specifications

Description
Value

Power

2400 W per DC power entry module (original series)
2800 W per DC power entry module (enhanced series)

Rated input voltage1

-48 VDC nominal in North America
-60 VDC nominal in the European Community
(range: -40.5 to -72 VDC (-75 VDC FOR 5mS))

-40 VDC to -72 VDC steady-state input voltage

Input current rating1

60 A maximum (1x)—Original series

40 A maximum (2x)—Enhanced series

Source DC service requirement1

Sufficient to supply the rated input current. Local codes apply.

Redundancy

2 DC power entry modules required for 2N redundancy

1 For each DC power entry module.



Caution To ensure that the chassis configuration complies with the required power budgets, use the on-line power calculator. Failure to properly verify the configuration may result in an unpredictable state if one of the power units fails. Contact your local sales representative for assistance.

Table A-4 Environmental Specifications

Description
Value

Temperature

Operating: 32° to 104°F (0° to 40°C)

Nonoperating: -4° to 149°F (-20° to 65°C)

Humidity

Operating: 10 to 85% noncondensing

Nonoperating: 5 to 95% noncondensing

Altitude

Operating: 0 to 10,000 ft (0 to 3,000 m)

Nonoperating: 0 to 15,000 ft (0 to 4,570 m)

Heat dissipation

8,296 BTU/hr maximum (original series)

9,554 BTU/hr maximum (enhanced series)

Acoustic noise

70 dBa maximum

Shock

Operating (halfsine): 21 in/sec (0.53 m/sec)

Nonoperating (trapezoidal pulse): 20 G1 , 52 in/sec (1.32 m/sec)

Vibration

Operating: 0.35 Grms2 from 3 to 500 Hz

Nonoperating: 1.0 Grms from3 to 500 Hz

1 G is a value of acceleration, where 1G equals 32.17 ft/sec2 (9.81 m/sec2).

2 Grms is the root mean square value of acceleration.