Cisco 10008 Router Hardware Installation Guide
Technical Specifications
Downloads: This chapterpdf (PDF - 354.0KB) | Feedback

Technical Specifications

Table Of Contents

Technical Specifications


Technical Specifications


Table A-1 lists the specifications for the Cisco 10008 router.

Table A-1 Cisco 10008 Router System Specifications 

Description
Specifications

Physical specifications

Weight: 130 lb (59.02 kg) fully configured chassis

Height: 21.75 in. (55.2 cm)

Width: 17.5 in. (44.4 cm)

Depth: 12.0 in. (30.4 cm)

Chassis depth with front cover: 13.75 in. (34.9 cm)

Mounting: 19 in. or 23 in. rack mountable (front or mid),
3 units per 7 ft rack

Temperature range

Operating: 41 degrees F to 104 degrees F (5 degrees C to 40 degrees C)
Short-term operating temperature is limited to 131 degrees F (55 degrees C) in compliance with Bellcore GR-63

Storage: -40 degrees F to 158 degrees F (-40 degrees C to 70 degrees C)

Relative humidity

Operating—nominal: 5 percent to 85 percent

Operating—short term: 5 percent to 90 percent

Storage: 5 percent to 95 percent

Operating altitude

-197 ft to 13,123 ft (-60 m to 4000 m)

Airflow

150 cfm1 through the system blower module

200 cfm through the system blower module if the exhaust temperature exceeds 45 degrees C

Power entry modules

DC PEM

Supports up to two separate -48 VDC input feeds by means of built-in two-position terminal blocks

Part Number: ESR-PWR-DC (Primary)
Part Number: ESR-PWR-DC\R (Redundant)

DC input voltage: -48 to -60 VDC

DC input current: 20A @ -48 VDC

Power consumption: 1200W maximum

Heat dissipation: 3768 Btu2 /hr

AC PEM

Part Number: ESR-PWR-AC (Primary)
Part Number: ESR-PWR-AC\R (Redundant)

AC inlet power connector: IEC 320 C20

AC input voltage: 100 to 240 VAC, 50/60 Hz, single phase

AC input current: 15 to 7 A

Power consumption: 1400W maximum

Heat dissipation: 4760 Btu/hr

Performance routing engine (PRE)

Part Number: ESR-PRE1 (Primary)
Part Number: ESR-PRE1/R (Redundant)

Power: 80W

Max per chassis: 2

Weight: 7.5 lb (3.41 kg)
Height: 16.0 in. (40.64 cm)
Depth: 9.97 in. (25.32 cm)
Width: 1.91 in. (4.84 cm)

Three Interface ports:

RJ-45 IEEE 802.3 Ethernet 100BASE-T

RJ-45 auxiliary (AUX) port for modem access

RJ-45 console (CON) port for terminal access

Two PCMCIA Flash card slots:

Slot 0

Slot 1

PRE PCMCIA Flash disk card options

40 MB—Part Number: ESR-PRE-MEM-FD40

128 MB—Part Number: ESR-PRE-MEM-FD128

PRE DRAM memory options

256 MB—Part Number: ESR-PRE-MEM-256M

512 MB—Part Number: ESR-PRE-MEM-512M

1 cfm = cubic feet per minute

2 Btu = British thermal units


For Specifications for Operating and Nonoperating Environments, see "Site Environmental Requirements" section on page 2-2.

For technical specifications for the Cisco 10008 line cards, see the Cisco 10000 Line Card Hardware Installation Guide.

For regulatory compliance and safety information, see the Regulatory Compliance and Safety Information for the Cisco 10000 Series Routers document.