Guest

Cisco ONS 15600 Series

Installing the Cisco ONS 15600 OC192/STM64 LR/LH 4 Port 1550 Card

  • Viewing Options

  • PDF (295.5 KB)
  • Feedback
Installing the Cisco ONS 15600 OC192/STM64 LR/LH 4 Port 1550 Card

Table Of Contents

Installing the Cisco ONS 15600 OC192/STM64 LR/LH 4 Port 1550 Card

OC192/STM64 LR/LH 4 Port 1550 Card

OC192/STM64 LR/LH 4 Port 1550 Card Features and Functions

OC192/STM64 LR/LH 4 Port 1550 Slots and Connectors

OC192/STM64 LR/LH 4 Port 1550 Performance Monitoring Thresholds

OC192/STM64 LR/LH 4 Port 1550 Faceplate and Block Diagram

OC192/STM64 LR/LH 4 Port 1550 Card-Level Indicators

OC192/STM64 LR/LH 4 Port 1550 Network-Level Indicators

OC192/STM64 LR/LH 4 Port 1550 Specifications

OC1928/STM64 LR/LH 4 Port 1550 Card OGI Connector Pinout

Replace an OC-192 Card

Force-Switch 1+1 Ports

Force-Switch Path Protection Paths

Clear a 1+1 Force Switch

Clear a Path Protection Force Switch

Related Documentation

Obtaining Documentation and Submitting a Service Request


Installing the Cisco ONS 15600 OC192/STM64 LR/LH 4 Port 1550 Card



Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.


Product Name: 15600-192L4-LR1550=

This document contains a description of OC192/STM64 LR/LH 4 Port 1550 card features, installation procedures, removal instructions, and technical specifications. Use this document in conjunction with the Cisco ONS 15600 Reference Manual, the Cisco ONS 15600 Procedure Guide, and the Cisco ONS 15600 Troubleshooting Guide when working with OC192/STM64 LR/LH 4 Port 1550 cards.

This document contains the following sections:

"OC192/STM64 LR/LH 4 Port 1550 Card" section

"OC192/STM64 LR/LH 4 Port 1550 Card Features and Functions" section

"Replace an OC-192 Card" section

"Related Documentation" section

"Obtaining Documentation and Submitting a Service Request" section

This document contains the following procedures:

"Replace an OC-192 Card" procedure


Note For information about circuits and card capacities, see the Cisco ONS 15600 Reference Manual.



Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.



Warning Read the installation instructions before you connect the system to its power source.



Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.



Warning Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock, keep hands and fingers out of the power supply bays and backplane areas.



Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not stare into the beam or view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.


OC192/STM64 LR/LH 4 Port 1550 Card

OC192/STM64 LR/LH 4 Port 1550 Card Features and Functions

The OC192/STM64 LR/LH 4 port 1550 card provides four long-range, Telcordia-compliant, GR-253 SONET OC-192 ports per card. The ports operate at 9953.28 Mbps over a single-mode fiber. The OC192/STM64 LR/LH 4 port 1550 card has four physical connector adapters with two fibers per connector adapter. The card supports STS-1 payloads and concatenated payloads at STS-3c, STS-12c, STS-24c, STS-48c, or STS-192c signal levels.

OC192/STM64 LR/LH 4 Port 1550 Slots and Connectors

You can install OC192/STM64 LR/LH 4 port 1550 cards in slots 1 through 4 and 11 through 14. The card provides four bidirectional OGI type connector adapters on the faceplate (angled downward), carrying two fiber strands (1 transmit and 1 receive). Only one transmit and receive pair is used per connector adapter. On a breakout cable, use port three, fiber 4 (transmit) and fiber 3 (receive).

OC192/STM64 LR/LH 4 Port 1550 Performance Monitoring Thresholds

Table 1 shows PM thresholds that apply to the OC192/STM64 LR/LH card.

Table 1 OC192/STM64 LR/LH Card Performance Monitoring Thresholds 

Performance Monitoring
Thresholds (15 min./1 day)
Near-End Line PMs for the OC192/STM64 LR/LH Card

CV-L

85040/850400

ES-L

87/864

FC-L

10/40

SES-L

1/4

UAS-L

3/10

PSC

1/5

PSD

300/600

Near-End Section PMs for the OC192/STM64 LR/LH Card

CV-S

10000/100000

ES-S

500/5000

SES-S

500/5000

SEFS-S

500/5000

Near-End Path PMs for the OC192/STM64 LR/LH Card

CV-P

75/750

ES-P

60/600

FC-P

10/10

SES-P

3/7

UAS-P

10/10

PPJC-Pdet

0/0

NPJC-Pdet

0/0

PPJC-Pgen

0/0

NPJC-Pgen

0/0

Far-End Line PMs for the OC192/STM64 LR/LH Card

CV-LFE

850400/85040

ES-LFE

864/87

FC-LFE

40/10

SES-LFE

4/1

UAS-LFE

10/3

Far-End Path PMs for the OC192/STM64 LR/LH Card

CV-PFE

75/750

ES-PFE

60/600

FC-PFE

10/10

SES-PFE

3/7

UAS-PFE

10/10

Physical PMs for the OC192/STM64 LR/LH Card

LBC-High

150%

LBC-Low

50%

OPT-High

120%

OPT-Low

80%

OPR-High

200%

OPR-Low

50%



Note SONET path PMs will not count unless IPPM is enabled. For additional information, see the Enabling Intermediate-Path Performance Monitoring section in the Cisco ONS 15600 Procedures Guide. To monitor SONET path PMs, log into the far-end node directly.


OC192/STM64 LR/LH 4 Port 1550 Faceplate and Block Diagram

Figure 1 shows the OC192/STM64 LR/LH 4 port 1550 faceplate and a block diagram of the card.

Figure 1 OC192/STM64 LR/LH 4 port 1550 faceplate and block diagram

OC192/STM64 LR/LH 4 Port 1550 Card-Level Indicators

Table 2 describes the functions of the card-level LEDs on the OC192/STM64 LR/LH card.

Table 2 OC192/STM64 LR/LH 4 port 1550 Card-Level Indicators  

Indicators
Color
Description
STAT LED

Red

Indicates a hardware fault; this LED is off during normal operation. Replace the unit if the STAT LED persists. During diagnostics, the LED will flash quickly during initialization and flash slowly during configuration synchronization.

SRV LED

Green

Indicates the service mode of the card. Green indicates the card is in use; off indicates when the card can be removed for service.

LASER ON

Green

The green LASER ON LED indicates that at least one of the card's lasers is active.


OC192/STM64 LR/LH 4 Port 1550 Network-Level Indicators

Table 3 describes the functions of the network-level LEDs on the OC192/STM64 LR/LH card.

Table 3 OC192/STM64 LR/LH 4 port 1550 Network-Level Indicators  

Indicators
Color
Description
SD LED

Blue

The blue SD LED indicates a signal degrade or condition such as a low signal level on at least one of the card's ports.

SF LED

Red

The red SF LED indicates a signal failure or condition such as LOS, LOF, or high BERs on at least one of the card's ports. The red SF LED also illuminates when the transmit and receive fibers are incorrectly connected. When the fibers are properly connected, the LED turns off.



Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not stare into the beam or view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.


OC192/STM64 LR/LH 4 Port 1550 Specifications

Table 4 shows the OC192/STM64 LR/LH card specifications.

Table 4 OC192/STM64 LR/LH 4 Port 1550 Card Specifications 

Specification Type
Description
Line

Bit Rate: 9.96 Gbps

Code: Scrambled NRZ

Fiber: 1550 nm Single Mode

Transmitter

Max. Transmitter Output Power: +7 dBm

Min. Transmitter Output Power: +4 dBm

Center Wavelength: 1530 nm to 1565 nm

Nominal Wavelength: 1550 nm

Transmitter: LN (Lithium Niobate) external modulator transmitter

Receiver

Max. Receiver Level: -9 dBm

Min. Receiver Level: -22 dBm

Receiver: APD/TIA

Link Loss Budget: 24 dB min., with no dispersion or 22 dB optical path loss at BER = 1- exp (-12) including dispersion

Loopback Mode

Payload

Note You must use a 19 to 24 dB (20 recommended) fiber attenuator when connecting a fiber loopback to an OC192/STM64 LR/LH 4 port 1550 card. Never connect a direct fiber loopback.

Connectors

OGI

Operating Temperature

23 to 122 degrees Fahrenheit (-5 to +50 degrees Celsius)

Operating Humidity

5 to 95%, non-condensing

Dimensions

Height: 16.50 in. (419 mm)

Width: 1.07 in. (27 mm)

Depth: 18.31 in. (465 mm)

Card Weight: 12.0 lbs (5.44 kg)

Compliance

Telcordia SONET, GR-253

When installed in a system, ONS 15600 cards comply with these safety standards: UL 60950, CSA C22.2 No. 950, EN 60950, IEC 60950

Eye Safety Compliance: Class 1 (21 CFR 1040.10 and 1040.11) and Class 1 (IEC 60825) laser products


OC1928/STM64 LR/LH 4 Port 1550 Card OGI Connector Pinout

Table 5 shows the OC192/STM64 LR/LH card OGI connector pinouts.

Table 5 OC192/STM64 LR/LH 4 Port 1550 Card OGI Connector Pinout

Connector
OGI Pin and Card Port

1

1

2

3

4

5

6

7

8

Transmit 1

Receive 1

2

1

2

3

4

5

6

7

8

Transmit 2

Receive 2

3

1

2

3

4

5

6

7

8

Transmit 3

Receive 3

4

1

2

3

4

5

6

7

8

Transmit 4

Receive 4


Replace an OC-192 Card

Purpose

This procedure is used to replace a faulty OC-192 card.

Tools/Equipment

Replacement OC-192 card

Prerequisite Procedures

None

Required/As Needed

As needed

Onsite/Remote

Onsite



Warning Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry could constitute an energy hazard.



Note Card removal raises an improper removal (IMPROPRMVL) alarm, but this clears after the card replacement is completed.



Step 1 Log into the node where you will replace the OC-192 card. If necessary, refer to the Cisco ONS 15600 Procedure Guide for a login procedure.

Step 2 Ensure that the card you are replacing does not carry traffic in a 1+1 group:

a. In the node view, click the Maintenance > Protection tabs.

b. Choose the first group listed under Protection Groups.

c. Verify that the slot number for the card you are replacing does not appear in the Selected Groups list. For example, if you are replacing the OC-192 card in slot 3, make sure that Selected Groups does not contain any entries that start with s3, regardless of the port.

d. Repeat Steps b and c for each protection group.

e. If any of the groups contain a port on the card you want to replace, perform the "Force-Switch 1+1 Ports" task.

Step 3 Ensure that the card you are replacing does carry path protection circuit traffic.


Note A port can be part of a 1+1 protection group or part of a path protection, but it cannot be configured for both. However, different ports on one card can be configured in different ways. If you move all of the traffic off some 1+1 ports, you still need to check whether the remaining ports are carrying path protection traffic.


a. In the CTC node view, click View > Go to Parent View.

b. Click the Circuits tab.

c. View the circuit source and destination ports and slots. If any circuits originate or terminate in the slot containing the card you are replacing, perform the "Force-Switch Path Protection Paths" task.


Note If the card you are replacing is not configured for any port or circuit protection, but does carry traffic, bridge and roll this traffic onto another card. Follow the "Bridge and Roll Traffic" procedure in the Cisco ONS 15600 Procedure Guide.


Step 4 Remove any fiber optic cables from the ports.

Step 5 Physically remove the card to be replaced from the ONS 15600 shelf:

a. Open the card ejectors.

b. Slide the card out of the slot.

Step 6 Physically replace the OC-192 card in the shelf:

a. Open the ejectors on the replacement card.

b. Slide the replacement card into the slot along the guide rails until it contacts the backplane.

c. Close the ejectors.


Note When you replace a card with an identical type of card, you do not need to make any changes to the database.


Step 7 Clear the Force switches.

To clear 1+1 Force switches, complete the "Clear a 1+1 Force Switch" task.

To clear Path Protection Force switches, complete the "Clear a Path Protection Force Switch" task.

Step 8 Once the card is placed in service and is receiving traffic, reset the card's physical receive power level threshold in CTC:

a. Double-click the newly installed card in CTC node view.

b. Click the Provisioning > Threshold tabs.

c. Click the Physical radio button.

d. Click Set OPM for each port on the card.


Force-Switch 1+1 Ports

Purpose

This procedure forces 1+1 protection group traffic from one port in the group to the other. It is used to remove traffic from a card for replacement.

Tools/Equipment

Installed OC-N cards

Prerequisite Procedures

Installed OC-192 card

Required/As Needed

As needed

Onsite/Remote

Onsite or remote



Note The Force switch is performed even if the destination path is degraded.



Step 1 In the CTC node view, click the Maintenance > Protection tabs.

Step 2 Select the protection group you want to Force-switch from Protection Groups.

Step 3 Under Selected Groups, choose the port belonging to the card you are replacing by clicking it. For example, if the card you are replacing contains the protect/standby port, click this port.

Step 4 Click the Force button.

Step 5 If the switch is successful, the group will say either FORCE TO WORKING or FORCE TO PROTECT.

Step 6 Return to the "Replace an OC-192 Card" procedure, or to your originating procedure.


Force-Switch Path Protection Paths

Purpose

This procedure forces all circuits in a path protection from one span to the other. It is used to remove traffic from a card that originates or terminates path protection circuits.

Tools/Equipment

Installed OC-192 cards

Prerequisite Procedures

None

Required/As Needed

As needed

Onsite/Remote

Onsite or remote



Note The Force switch is performed even if the destination path is degraded.



Step 1 In the CTC node view, click View > Go to Network View if this view is not already displayed.

Step 2 Click the Circuits tab.

Step 3 Note, print, or export the list of circuits from this tab, and mark the circuits involving the slot containing the card you are replacing.

For information about doing this from CTC, refer to the procedures in the Cisco ONS 15600 Procedures Guide.

Step 4 In the network map, right-click a circuit connected to the node where you are performing the Force switch. Choose Circuits from the shortcut menu.

The Circuits window is displayed.

Step 5 Verify that this list contains the same circuits that you marked in the list.

Step 6 Choose Force from the pull-down menu at the bottom of the window.

If the switch was successful, all circuits will show FORCE in the Switch State column.

Step 7 Return to the"Replace an OC-192 Card" procedure, or to your originating procedure.


Clear a 1+1 Force Switch

Purpose

This procedure clears a 1+1 protection group Force switch. It is used to revert traffic to the original port after the card has been serviced.

Tools/Equipment

None

Prerequisite Procedures

"Force-Switch 1+1 Ports" section

Required/As Needed

As needed

Onsite/Remote

Onsite or remote



Note If the ports terminating a span are configured as revertive, clearing a Manual or Force switch to protect (or working) moves traffic back to the working (or protect) port. If ports are not configured as revertive, clearing a Manual or Force switch to protect does not move traffic back.



Step 1 In the CTC node view, click the Maintenance > Protection tabs.

Step 2 Under Protection Groups, click the protection group containing the port you want to clear.

Step 3 Under Selected Group, click the port you want to clear.

Step 4 In the Inhibit Switching area, click Clear.

Step 5 Click Yes in the confirmation dialog box.

The lockout is cleared.

The Force switch is cleared. Traffic will revert to the original port if the group was configured for revertive switching.

Step 6 Return to the "Replace an OC-192 Card" procedure, or to your originating procedure.


Clear a Path Protection Force Switch

Purpose

This procedure clears a path protection circuit Force switch. It is used to revert traffic to the original circuits after the card has been serviced.

Tools/Equipment

None

Prerequisite Procedures

"Force-Switch Path Protection Paths" section

Required/As Needed

As needed

Onsite/Remote

Onsite or remote



Step 1 In the CTC node view, click View > Go to Network View if this view is not already displayed.

Step 2 In the network map, right-click the span that you Force switched. Choose Circuits from the shortcut menu.

The Circuits window is displayed.

Step 3 Choose Clear from the pull-down menu at the bottom of the window.

The Force switch is cleared.


Note Active circuits are displayed green in the Circuits window. Standby circuits are displayed purple in the window.



Note If these circuits are configured for revertive switching, they will revert to original paths after the revertive time expires. If they are not revertive, they will not move back unless you Force-switch them back. If the switch state is clear, you can complete the "Force-Switch Path Protection Paths" task again to force traffic back to the original path.


Step 4 Return to the"Replace an OC-192 Card" procedure, or to your originating procedure.


Related Documentation

DOC-7814303= Cisco ONS 15600 Procedure Guide

DOC-7814706= Cisco ONS 15600 Reference Manual

DOC-7814707= Cisco ONS 15600 Troubleshooting Guide

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.