Guest

Cisco ONS 15300 Series

Installing the CE-100T-8 Card in the Cisco ONS 15310-CL and Cisco ONS 15310-MA

  • Viewing Options

  • PDF (669.1 KB)
  • Feedback
Installing the CE-100T-8 Card in the Cisco ONS 15310-CL and Cisco ONS 15310-MA

Table Of Contents

Installing the CE-100T-8 Card in the Cisco ONS 15310-CL and Cisco ONS 15310-MA

CE-100T-8 Card Description

Faceplate and Block Diagram

Card-Level Indicators

Port-Level Indicators

CE-100T-8 Card Specifications

Install the CE-100T-8 Card in the Cisco ONS 15310-CL

Install the CE-100T-8 Card in the Cisco ONS 15310-MA

Related Documentation

Obtaining Documentation and Submitting a Service Request


Installing the CE-100T-8 Card in the Cisco ONS 15310-CL and Cisco ONS 15310-MA


Product Name: 15310-CE-100T-8, 15310-P-CE-100T-8

This document provides a card description, specifications, and installation procedure for the Cisco ONS 15310-CL and Cisco ONS 15310-MA CE-100T-8 card. As appropriate use this document in conjunction with the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide, the Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual, and the Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide.

This document contains the following sections:

CE-100T-8 Card Description

CE-100T-8 Card Specifications

Install the CE-100T-8 Card in the Cisco ONS 15310-CL

Install the CE-100T-8 Card in the Cisco ONS 15310-MA

Related Documentation

Obtaining Documentation and Submitting a Service Request

CE-100T-8 Card Description

This section describes the features and functions of the Layer 1 Ethernet card, the CE-100T-8. The card is compatible with both the ONS 15310-CL and the ONS 15310-MA.


Note The CE-100T-8 card with product ID (PID) 15310-CE-100T-8 is not compatible with the ONS 15310-MA. The 15310-P-CE-100T-8 is compatible with both the ONS 15310-MA and ONS 15310-CL shelf assemblies. If you install a 15310-CE-100T-8 in an ONS 15310-MA shelf assembly, you will receive a mismatched equipment alarm (MEA). You can view the PID under the node view Inventory tab in CTC.


The CE-100T-8 card maps 8-port 10/100-Mbps Ethernet-encapsulated traffic into SONET payloads, making use of low-order (VT1.5) virtual concatenation (VCAT), high-order (STS-1, STS-3c) VCAT, generic framing procedure (GFP), and Point-to-Point Protocol/high-level data link control (PPP/HDLC) framing protocols. It also supports the link capacity adjustment scheme (LCAS), which allows hitless dynamic adjustment of SONET link bandwidth. The CE-100T-8 card provides eight RJ-45 10/100-Mbps Ethernet ports on the faceplate of the card. An inactive RJ-11 console port is also on the faceplate.

The circuit types supported are:

STS-1 and STS-3c CCAT

STS-1-Nv VCAT (N = 1-3)

STS-1-Nv LCAS (N = 1-3)

STS-1-2v software LCAS (SW-LCAS) (compatible with ML-Series cards only)

VT1.5-Nv VCAT (N = 1-64)

VT1.5-Nv LCAS (N = 1-64)

Each 10/100 Ethernet port can be mapped to a SONET channel in increments of VT1.5 or STS-1 granularity. There are eight backend packet-over-SONET (POS) ports (VCAT groups [VCGs]) available on the CE-100T-8 card. Additionally, the CE-100T-8 card supports packet processing, classification, quality of service (QoS)-based queuing, and traffic scheduling.

Faceplate and Block Diagram

Figure 1 shows the CE-100T-8 card faceplate and block diagram.

Figure 1 CE-100T-8 Faceplate and Block Diagram

Card-Level Indicators

The CE-100T-8 card faceplate has two card-level LED indicators, described in Table 1.

Table 1 CE-100T-8 Card-Level Indicators  

Card-Level LEDs
Description

SF LED (Red)

The red FAIL LED indicates that the card processor is not ready or that a catastrophic software failure occurred on the CE-100T-8 card. As part of the boot sequence, the FAIL LED blinks until the software deems the card operational, then it turns off.

ACT LED (Green)

The ACT LED provides the operational status of the CE-100T-8. When the ACT LED is green, it indicates that the CE-100T-8 card is active and the software is operational; otherwise, it is off.


Port-Level Indicators

The CE-100T-8 card has two LEDs embedded into each of the eight Ethernet-port RJ-45 connectors. The LEDs are described in Table 2.

Table 2 CE-100T-8 Port-Level Indicators

Port-Level Indicators
Description

ACT LED (Amber)

A steady amber LED indicates a link is detected, but there is an issue inhibiting traffic. A blinking amber LED means traffic is flowing.

LINK LED (Green)

A steady green LED indicates that a link is detected, but there is no traffic. A blinking green LED flashes at a rate proportional to the level of traffic being received and transmitted over the port.

Both ACT and LINK LED OFF

Unlit green and amber LEDs indicate no traffic.


CE-100T-8 Card Specifications

The CE-100T-8 card has the following specifications.

Environmental

Operating temperature

C-Temp: 0 to +55 degrees Celsius (32 to 131 degrees Fahrenheit)

Operating humidity: 5 to 95%, noncondensing

Power consumption: 1.10A, 35W

Dimensions

Height: 176 mm (6.93 in.)

Width: 34.29 mm (1.35 in.)

Depth: 238.25 mm (9.38 in.)

Weight (not including clam shell): 0.499 kg (1.1 lb)

Install the CE-100T-8 Card in the Cisco ONS 15310-CL

Use this section if you are installing the CE-100T-8 card in an ONS 15310-CL expansion slot for the first time. After you become familiar with ONS 15310-CL card installation and bootup, use this section as a reference.


Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Caution Do not install the CE-100T-8 card in an ONS 15310-CL if the ambient temperature exceeds 131 degrees Fahrenheit (55 degrees Celsius).


Step 1 Install the CE-100T-8 card in the expansion slot (Figure 2):

a. Open the card ejector.

b. Slide the card along the guide rails into the slot.

c. Close the ejector by pushing it to the right.

d. Lock the cards into place by tightening the ejector locking screws.


Note The CE-100T-8 cards are hot-pluggable, so they may be inserted or removed without turning off the power to the ONS 15310-CL.


Figure 2 Installing the Cisco ONS 15310-CL CE-100T-8 Card

Step 2 Verify the CE-100T-8 card LED activity:

a. Verify that the red FAIL LED is off

b. Verify that the green ACT LED is on.

Step 3 If you remove power from the ONS 15310-CL chassis, and then restore it, check the chassis LED activity:

a. Verify that the chassis red FAIL LED blinks for 20 to 30 seconds, then turns off.

b. Verify that the chassis ALARM LED is off.

c. Verify the chassis green PWR LED is on. (It is amber only if one DC power source is on and operating.)

d. Verify that the chassis green SYNC LED is on.

Step 4 When you log into CTC, verify that the card appears properly on the CTC node view screen.


Install the CE-100T-8 Card in the Cisco ONS 15310-MA

Use this section if you are installing the CE-100T-8 card in an ONS 15310-MA expansion slot for the first time. After you become familiar with ONS 15310-MA card installation and bootup, use this section as a reference.


Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Caution Do not install the CE-100T-8 card in an ONS 15310-MA if the ambient temperature exceeds 131 degrees F (55 degrees C).


Step 1 Install the CE-100T-8 card in a traffic card slot:

a. Open the card ejector.

b. Use the ejector at the top of the card and firmly slide the card along the guide rails until the card plugs into the receptacle at the back of the slot.

c. Verify that the card is inserted correctly and close the ejector on the card.


Note The CE-100T-8 cards are hot-pluggable, so they can be inserted or removed without turning off the power to the ONS 15310-MA.


Step 2 Verify the CE-100T-8 card LED activity:

a. Verify that the red FAIL LED is off.

b. Verify that the green ACT LED is on.

Step 3 When you log into CTC, verify that the card appears properly in CTC node view.

Stop. You have completed this procedure.


Related Documentation

Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide

Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.


This document is to be used in conjunction with the documents listed in the "Related Documentation" section.