Table Of Contents
Installing the Wall Mount Brackets for the
Cisco ONS 15310-CL
Product Name: 15310C-WALLKIT
This document explains how to install the Cisco ONS 15310-CL wall mount brackets. It also contains a description of the wall mount brackets, installation equipment and procedures, and a list of specifications. As appropriate, use this document in conjunction with the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide, the Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual, and the Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide when working with the wall mount brackets.
This document contains the following sections:
Wall-Mount Brackets Description
The wall-mount brackets allow you to mount a single ONS 15310-CL shelf assembly and associated cabling to a 3/4-inch plywood panel that is secured to a wall.
Note Cisco does not provide instructions for securing the plywood panel to the wall, but does provide a template for predrilling holes in the plywood. Secure the plywood according to your site plan instructions.
You can mount the shelf assembly in an east-west direction so that the front of the assembly faces either left or right, or in a north-south orientation, where the front of the shelf assembly faces upward. A drip pan is provided with the wall-mount bracket for installation sites where the ONS 15310-CL is installed over a combustible surface. Attachment points for the tie-bar (15310-TIE-BAR-19) are also provided to allow for cable management.
Figure 1 shows installed wall-mount brackets and ONS 15310-CL in an east-west orientation.
Figure 1 ONS 15310-CL Wall-Mount Brackets (East-West)
Figure 2 shows installed wall-mount brackets and ONS 15310-CL in a north-south orientation.
Note If installing the ONS 15310-CL in a north-south orientation, make sure you install it so the expansion slot faces upward. Do not install the chassis facing downward because the drip pan will physically interfere with cabling.
Figure 2 ONS 15310-CL Wall-Mount Brackets (North-South)
Figure 3 Wall-Mounted ONS 15310-CL and AC Power Supply (East-West)
Figure 4 Wall-Mounted ONS 15310-CL and DC Power Supply (East-West)
Wall-Mount Brackets Specifications
–Operating temperature: -40 to +65 degrees Celsius (-40 to 149 degrees Fahrenheit)
–Operating humidity: 5 to 90%, noncondensing
•Dimensions (this includes the shelf assembly)
–23.25 in. x 21.00 in. x 3.25 in. (59.06 cm x 53.34 cm x 8.255 cm)
–Weight (including shelf assembly and expansion card): Approximately 17 lbs. (7.71 kg)
Install the Wall-Mount Brackets and ONS 15310-CL
The following parts are included in the wall-mount bracket kit. Numerals in parentheses indicate the quantity of the item.
•Panhead screws, 8-32 x 0.315 in. (10)
•Hex wood screws, 1/4-14 x 0.75 in. (6)
•Wall-mount brackets (2)
•Drip pan (1)
•Wall-mount bracket template (1)
You will also need adhesive tape, a #2 Phillips screwdriver, an electric drill with a 5/32-inch drill bit, and a 3/8-inch nut driver.
Step 1 Line up the four screw holes on the left wall-mount bracket with the holes on the left side of the ONS 15310-CL chassis (Figure 1).
Step 2 Install and tighten four panhead screws.
Step 4 In the desired location on the plywood, use tape to secure the wall-mount bracket template to the plywood in the desired orientation (north-south or east-west).
Step 5 Drill the four screw holes using an electric drill, and remove the template from the plywood (Figure 4).
Figure 5 Template for Drilling Wall-Mount Bracket Holes
Step 6 Screw four hex wood screws into the plywood approximately halfway, using the 3/8-inch nut driver.
Step 7 Slide the keyholes on the brackets over the screws installed on the plywood, and tighten all four screws until secure.
Caution Because the ONS 15310-CL shelf assembly is not mounted in a standard rack, you must attach the shelf assembly to appropriate grounding, such as a grounding bar, as approved by your local electrical inspection authority.
Install the Drip Pan
To install the drip pan on a chassis in an east-west orientation, line up the drip pan with the two available holes on the bottom wall-mount bracket, and install and tighten two hex wood screws (Figure 1).
To install the drip pan on a chassis in a north-south orientation, line up the two holes on the outside rails of the drip pan with the lowest hole on each of the wall-mount brackets, and install and tighten two panhead screws (Figure 2). Install and tighten two hex wood screws in the holes on the face of the drip pan.
Install the Cable Tie-Bar
As necessary, install the cable tie-bar (15310-TIE-BAR-19) according to the instructions that ship with the cable-tie bar kit. The tie-bar is used for cable management.
Figure 6 shows the tie-bar installed on a left-facing ONS 15310-CL chassis in an east-west orientation.
Figure 6 Tie-Bar Installation on an East-West Wall-Mount Orientation
•Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide
•Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual
•Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
Subscribe to the What's New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2011 Cisco Systems, Inc. All rights reserved.