Cisco ONS SDH TL1 Command Guide, Release 9.8.x
Chapter 26, Conditions
Downloads: This chapterpdf (PDF - 256.0KB) The complete bookPDF (PDF - 11.07MB) | Feedback

Table of Contents

Conditions

Conditions

This chapter lists the conditions for TL1 commands and autonomous messages for the Cisco ONS 15454 SDH, Cisco ONS 15454 M2, and Cisco ONS 15454 M6, Release 9.4. These conditions are listed below.

Conditions include any problem detected on an Cisco ONS 15454 SDH, Cisco ONS 15454 M2, or Cisco ONS 15454 M6 shelf. They can include standing or transient notifications. A snapshot of all current raised, standing conditions on the network, node, or card can be retrieved in the Cisco Transport Controller (CTC) Conditions window or using the RTRV-COND commands. (In addition, some but not all cleared conditions are also found in the History tab in CTC.)


Note The Condition that apply to Cisco ONS 15454 SDH also applies to Cisco ONS 15454 M2 and Cisco ONS 15454 M6.


 

Table 26-1 Conditions

Condition
Description

AIS

Alarm Indication Signal

AIS-L

Alarm Indication Signal—Line

ALS

Automatic Laser Shutdown

AMPLI-INIT

Optical Amplifier Initialization

APC-DISABLED

Automatic Power Control Disabled

APC-FAIL

Automatic Power Control Failure

APSB

Byte Failure

APSC-IMP

Improper Automatic Protection Switch (APS) Code

APSCDFLTK

Default K Byte

APSCINCON

Inconsistent APS Code

APSCM

Protection Switching Channel Match Failure

APSCNMIS

Node ID Mismatch

APSIMP

APS Invalid Mode

APSMM

APS Mode Mismatch

AS-CMD

Alarms Suppressed By User Command

AS-MT

Alarms Suppressed For Maintenance

AU-AIS

AIS—Administration Unit—Alarm Indication Signal

AU-LOF

LOF—Administration Unit—Loss of Multi Frame

AU-LOP

LOP—Administration Unit—Loss of Pointer

AUD-LOG-LOSS

Audit Log 100 Percent Full—Oldest records will be lost

AUD-LOG-LOW

Audit Log 80 Percent Full

AUTOLSROFF

Automatic Laser Shutoff Due To High Temperature

AUTORESET

Automatic System Reset

AUTOSW-AIS-SNCP

Automatic SNCP Switch caused by AIS

AUTOSW-LOP-SNCP

Automatic SNCP Switch Caused By LOP

AUTOSW-PDI-SNCP

Automatic SNCP Switch Caused By PDI

AUTOSW-SDBER-SNCP

Automatic SNCP Switch Caused By SDBER

AUTOSW-SFBER-SNCP

Automatic SNCP Switch Caused By SFBER

AUTOSW-UNEQ-SNCP

Automatic SNCP Switch Caused By UNEQ

AWG-DEG

AWG Temperature Degrade

AWG-FAIL

AWG Temperature Failure

AWG-OVERTEMP

AWG Over-Temperature

AWG-WARM-UP

AWG Warm Up

BAT-FAIL

Battery Failure

BAT-HGH-VLT

High Volt

BAT-LOW-VLT

Low Volt

BKUPMEMP

Primary Non-Volatile Backup Memory Failure

CARLOSS

Carrier Loss On The LAN

CASETEMP-DEG

Case Temperature Degrade

CKTDOWN

Signaling unable to set up circuit

CLDRESTART

Cold Restart

COMIOXC

IO Slot To XCON Communication Failure

COMM-FAIL

Plug-in Module Communication Failure

CONTBUS-A-18

TCC A To DCC A Processor Communication Failure

CONTBUS-B-18

TCC B To DCC B Processor Communication Failure

CONTBUS_A

Controller A To Shelf Slot Communication Failure

CONTBUS_B

Controller B To Shelf Slot Communication Failure

CTNEQPT-MISMATCH

Connection Equipment Mismatch

CTNEQPT-PBPROT

Interconnection Equipment Failure—Protect XC Payload Bus

CTNEQPT-PBWORK

Interconnection Equipment Failure—Working XC Payload Bus

DATAFLT

Software Fault—Data Integrity Fault

DBOSYNC

Standby Database Out of Sync

DS3-MISM

DS3 Frame Format Mismatch

DSP-COMM-FAIL

DSP Communication Failure

DSP-FAIL

DSP Failure

DUP-IPADDR

IP address already in use within the same DCC Area

DUP-NODENAME

Node name already in use within the same DCC area

E-W-MISMATCH

Both Ends Of Fiber Provisioned As East Or Both As West

E3-ISD

E3 Idle Condition

EHIBATVG

Extreme High Volt

ELWBATVG

Extreme Low Volt

EOC

RS-DCC Termination Failure

EQPT

Equipment Failure

EQPT-MISS

Replaceable Equipment/Unit is Missing

ERFI-P-CONN

Enhanced Remote Failure Indication—Path—Connectivity

ERFI-P-PAYLD

Enhanced Remote Failure Indication—Path—Payload

ERFI-P-SRVR

Enhanced Remote Failure Indication—Path—Server

ERROR-CONFIG

Error in Startup Configuration

ETH-LINKLOSS

Rear Panel Ethernet Link Removed

EXCCOL

Excess Collisions On The LAN

EXERCISE-RING-FAIL

Exercise Request on Ring Failed

EXERCISE-RING-REQ

Exercise Request on Ring

EXERCISE-SPAN-FAIL

Exercise Request on Span Failed

EXERCISE-SPAN-REQ

Exercise Request on Span

EXT

Failure Detected External To The NE

EXTRA-TRAF-PREEMPT

Extra Traffic Preempted

FAILTOSW

Failure To Switch To Protection

FAILTOSW-HO

Failure To Switch To Protection—High Order Path

FAILTOSW-LO

Failure To Switch To Protection—Low Order Path

FAILTOSWR

Failure To Switch To Protection—Ring

FAILTOSWS

Failure To Switch To Protection—Span

FAN

Fan Failure

FANDEGRADE

Partial Fan Failure

FE-AIS

Far End AIS

FE-DS1-MULTLOS

Far End Multiple DS1 LOS Detected On DS3

FE-DS1-NSA

Far End DS1 Equipment Failure—Non Service Affecting

FE-DS1-SA

Far End DS1 Equipment Failure—Service Affecting

FE-DS1-SNGLLOS

Far End Single DS1 LOS

FE-DS3-NSA

Far End DS3 Equipment Failure—Non Service Affecting

FE-DS3-SA

Far End DS3 Equipment Failure—Service Affecting

FE-E1-MULTLOS

Far end multiple E1 LOS detected on E3

FE-E1-NSA

Far end E1 eqpt fail non service affecting

FE-E1-SA

Far end E1 eqpt fail service affecting

FE-E1-SNGLLOS

Far end signal E1 LOS

FE-E3-NSA

Far end E3 eqpt fail non service affecting

FE-E3-SA

Far end E3 eqpt fail service affecting

FE-EQPT-NSA

Far End Common Equipment Failure—Non Service Affecting

FE-EXERCISING-RING

Far End Exercising Ring

FE-EXERCISING-SPAN

Far End Exercising Span

FE-FRCDWKSWPR-RING

Far End Working Facility Forced To Switch To Protection—Ring

FE-FRCDWKSWPR-SPAN

Far End Working Facility Forced To Switch To Protection—Span

FE-IDLE

Far End IDLE

FE-LOCKOUTOFPR-ALL

Far End Lockout Of Protection—All Spans

FE-LOCKOUTOFPR-RING

Far End Lockout Of Protection—Ring

FE-LOCKOUTOFPR-SPAN

Far End Lockout Of Protection—Span

FE-LOCKOUTOFWK-RING

Far End Lockout Of Working—Ring

FE-LOCKOUTOFWK-SPAN

Far End Lockout Of Working—Span

FE-LOF

Far End LOF

FE-LOS

Far End LOS

FE-MANWKSWPR-RING

Far End Manual Switch Of Working Facility To Protection—Ring

FE-MANWKSWPR-SPAN

Far End Manual Switch Of Working Facility To Protection—Span

FE-SDPRLF

APS Channel—Far End Protection Line Signal Degrade

FEC-MISM

FEC Mismatch

FEPRLF

Far End Protection Line Failure

FIBERTEMP-DEG

Fiber Temperature Degrade

FORCED-REQ

Forced Switch Request

FORCED-REQ-RING

Forced Switch Request On Ring

FORCED-REQ-SPAN

Forced Switch Request On Span

FRCDSWTOINT

Forced Switch To Internal Clock

FRCDSWTOPRI

Forced Switch To Primary Reference

FRCDSWTOSEC

Forced Switch To Second Reference

FRCDSWTOTHIRD

Forced Switch To Third Reference

FRNGSYNC

Free Running Synchronization Mode

FSTSYNC

Fast Start Synchronization Mode

FULLPASSTHR-BI

Bidirectional Full Pass Through Is Active

GAIN-HDEG

Optical Amplifier Gain Degrade High

GAIN-HFAIL

Optical Amplifier Gain Failure High

GAIN-LDEG

Optical Amplifier Gain Degrade Low

GAIN-LFAIL

Optical Amplifier Gain Failure Low

GCC-EOC

GCC Termination Failure

GE-OOSYNC

Gigabit Ethernet Out of Sync

HI-LASERBIAS

Equipment High Laser Bias

HI-RXPOWER

Equipment High Receive Power

HI-TXPOWER

Equipment High Transmit Power

HITEMP

High Temperature

HLDOVRSYNC

Holdover Synchronization Mode

HP-RFI

Remote Failure Indication—High Order—Remote Failure/Alarm Indication

HP-TIM

High Order—Trace Identifier Mismatch Failure

HP-UNEQ

Signal Label Mismatch Failure (SLMF)—Unequipped High Order—Path Unequipped

I-HITEMP

Industrial High Temperature

IMPROPRMVL

Improper Removal

INC-GFP-OUTOFFRAME

Out Of Frame Detected by Generic Framing Protocol (GFP) Receiver

INC-GFP-SIGLOSS

Client Signal Loss Frames Detected by GFP Receiver

INC-ISD

DS3 Idle Condition

INC-SIGLOSS

Incoming Signal Loss on Fibre Channel Interface

INC-SYNCLOSS

Incoming Synchronization Loss on Fibre Channel Interface

INC_GFP_SYNCLOSS

Client Synchronization Loss Frames Detected by GFP Receiver

INHSWPR

Inhibit Switch To Protect Request On Equipment

INHSWWKG

Inhibit Switch To Working Request On Equipment

INTRUSION-PSWD

Security Intrusion Attempt Detected—See Audit Log

INVMACADR

Invalid MAC Address

IOSCFGCOPY

Ios Config Copy In Progress

KB-PASSTHR

K Bytes Pass-Through Is Active

KBYTE-APS-CHANNEL-FAILURE

Kbyte Channel Failure

LAN-POL-REV

Lan Connection Polarity Reversed

LASER-APR

Laser Auto Power Reduction

LASERBIAS-DEG

Laser Bias Degrade

LASERBIAS-FAIL

Laser Bias Failure

LASEREOL

Laser Approaching End of Life

LASERTEMP-DEG

Laser Temperature Degrade

LKOUTPR-R

Lockout Of Protection—Ring

LKOUTPR-S

Lockout Of Protection—Span

LKOUTWK-R

Lockout Of Working—Ring

LKOUTWK-S

Lockout Of Working—Span

LMP-HELLODOWN

Link Management Protocol (LMP) Hello FSM to Control Channel down

LMP-NDFAIL

LMP Neighbor Discovery has failed

LO-RXPOWER

Equipment Low Receive Power

LO-TXPOWER

Equipment Low Transmit Power

LOA

Loss of Alignment

LOC

Loss of Channel

LOCKOUT-REQ

Lockout Switch Request On Facility or Equipment

LOCKOUT-REQ-RING

Lockout Switch Request On Ring

LOCKOUTOFPR

Lockout Of Protection

LOF

Loss Of Frame

LOM

Loss of Multi-Frame

LOS

Loss Of Signal

LOS-CONT

Loss Of Continuity

LP-PLM

Signal Label Mismatch Failure (SLMF)—PLM Low Order—Path Label Mismatch

LP-RFI

RFI—Low Order—Remote Failure/Alarm Indication

LP-TIM

TIM Low Order—Trace Identifier Mismatch Failure

LP-UNEQ

Signal Label Mismatch Failure (SLMF)—Unequipped Low Order—Path Unequipped

LPBKCRS

Cross-connect Loopback

LPBKDS1FEAC

DS1 Loopback Due To Far End Alarm and Control (FEAC) Command

LPBKDS3FEAC

DS3 Loopback Due To FEAC Command

LPBKDS3FEAC-CMD

DS3 Loopback Command Sent To Far End

LPBKE1FEAC

E1 loopback due to FEAC command

LPBKE3FEAC

E3 loopback due to FEAC command

LPBKE3FEAC-CMD

E3 loopback command sent to far end

LPBKFACILITY

Facility Loopback

LPBKTERMINAL

Terminal Loopback

MAN-REQ

Manual Switch Request

MANRESET

Manual System Reset

MANSWTOINT

Manual Switch To Internal Clock

MANSWTOPRI

Manual Switch To Primary Reference

MANSWTOSEC

Manual Switch To Second Reference

MANSWTOTHIRD

Manual Switch To Third Reference

MANUAL-REQ-RING

Manual Switch Request On Ring

MANUAL-REQ-SPAN

Manual Switch Request On Span

MEA

Mismatch Of Equipment And Attributes

MEM-GONE

Free Memory On Card Near Zero

MEM-LOW

Free Memory On Card Very Low

MFGMEM

Manufacturing Data Memory (EEPROM Failure)

MS-AIS

AIS—Multiplex Section—Alarm Indication Signal

MS-EOC

Multiplex Section DCC Termination Failure

MS-RFI

RFI—Multiplex Section—Remote Failure/Alarm Indication

MSSP-OOSYNC

Procedural Error—MS-SPRing out of sync

NO-CONFIG

No Startup Configuration

NTWTPINC

Network Topology Incomplete

OCHNC-ACTIV-FAIL

Optical Channel Activation Failure

OCHNC-DEACTIV-FAIL

Optical Channel Deactivation Failure

OCHNC-FAIL

Optical Channel Connection Failure

OCHNC-INC

Optical Channel Incomplete

ODUK-AIS-PM

ODUk: Alarm Indication Signal

ODUK-BDI-PM

ODUk: PM Backward Defect Indication

ODUK-LCK-PM

ODUk: Locked Defect —Performance Monitoring (PM)

ODUK-OCI-PM

ODUk: Open Connection Indication

ODUK-SD-PM

ODUk: Signal Degrade

ODUK-SF-PM

ODUk: Signal Failure

ODUK-TIM-PM

ODUk: Trail Trace Identifier Mismatch

OOU-TPT

Out of Use—Transport Failure

OPTNTWMIS

Optical Network Type Mismatch

OPWR-HDEG

Optical Power Degrade High

OPWR-HFAIL

Optical Power Failure High

OPWR-LDEG

Optical Power Degrade Low

OPWR-LFAIL

Optical Power Failure Low

OTUK-AIS

OTUk: Alarm Indication Signal

OTUK-BDI

OTUk: Backward Defect Indication

OTUK-LOF

OTUk: Loss Of Frame

OTUK-SD

OTUk: Signal Degrade

OTUK-SF

OTUk: Signal Failure

OTUK-TIM

OTUk: Trail Trace Identifier Mismatch

OUT-OF-SYNC

8B10B Out of Sync

PDI-P

Payload Defect Indication—Path

PEER-NORESPONSE

Peer Card Not Responding

PORT-CODE-MISM

Pluggable port security code mismatch

PORT-COMM-FAIL

Module Communication Failure

PORT-MISMATCH

Pluggable port rate mismatch

PORT-MISSING

Pluggable port missing

PRC-DUPID

Duplicate Node ID

PROTNA

Protection Unit Not Available

PTIM

Payload Type Identifier Mismatch

PWR-REDUN

Redundant Power Capability Lost

RAI

Remote Alarm Indication

RCVR-MISS

Facility Termination Equipment—Receiver Missing

RFI

Remote Failure Indication

RFI-L

Remote Failure Indication—Line

RING-ID-MIS

Ring Id Mismatch

RING-MISMATCH

Far End Of Fiber Is Provisioned With Different Ring ID

RING-SW-EAST

Ring Switch Is Active On The East Side

RING-SW-WEST

Ring Switch Is Active On The West Side

RSVP-HELLODOWN

RSVP Hello FSM to Neighbor down

RUNCFG-SAVENEED

Need to Save Running Config

SD

Signal Degrade

SD-L

Bit Error Rate (BER) Threshold Exceeded For Signal Degrade—Line

SDBER-EXCEED-HO

BER Threshold Exceeded For Signal Degrade—High Order

SF

Signal Failure

SF-L

BER Threshold Exceeded For Signal Failure—Line

SFBER-EXCEED-HO

BER Threshold Exceeded For Signal Failure—High Order

SFTWDOWN

Software Download In Progress

SH-INS-LOSS-VAR-DEG-HIGH

Shutter Insertion Loss Variation Degrade High

SH-INS-LOSS-VAR-DEG-LOW

Shutter Insertion Loss Variation Degrade Low

SHUTTER-OPEN

Shutter Open

SNTP-HOST

Simple Network time Protocol (SNTP) Host Failure

SPAN-SW-EAST

Span Switch Is Active On The East Side

SPAN-SW-WEST

Span Switch Is Active On The West Side

SQM

Sequence Mismatch

SQUELCH

Ring Is Squelching Traffic

SQUELCH-PATH

Squelching Path

SQUELCHED

Equipment Squelched

SSM-DUS

Do Not Use For Synchronization

SSM-FAIL

Failed To Receive Synchronization Status Message

SSM-LNC

ITU-T G.812—Local Node Clock traceable

SSM-OFF

Synchronization Status Messages Are Disabled On This Interface

SSM-PRC

ITU-T G.811—Primary Reference Clock traceable

SSM-PRS

Stratum 1 Primary Reference Source Traceable

SSM-RES

Reserved For Network Synchronization Use

SSM-SDH-TN

ITU-T G.812—Transit Node Clock traceable

SSM-SETS

ITU-T G.813—Synchronous Equipment Timing Source traceable

SSM-SMC

SDH Minimum Clock Traceable

SSM-ST2

Stratum 2 Traceable

SSM-ST3

Stratum 3 Traceable

SSM-ST3E

Stratum 3E Traceable

SSM-ST4

Stratum 4 Traceable

SSM-STU

Synchronized—Traceability Unknown

SSM-TNC

Transit Node Clock Traceable

SWMTXMOD

Switching Matrix Module Failure

SWTOPRI

Switch To Primary Reference

SWTOSEC

Switch To Second Reference

SWTOTHIRD

Switch To Third Reference

SYNC-FREQ

Synchronization Reference Frequency Out Of Bounds

SYNCPRI

Primary Synchronization Reference Failure

SYNCSEC

Secondary Synchronization Reference Failure

SYNCTHIRD

Third Synchronization Reference Failure

SYSBOOT

System Reboot

TIM

TIM Section—Trace Identifier Mismatch Failure

TIM-MON

TIM Section Monitor—Trace Identifier Mismatch Failure

TPTFAIL

Transport layer failure

TRMT

Transmit Failure

TRMT-MISS

Facility Termination Equipment—Transmitter Missing

TU-AIS

AIS—Tributary Unit—Alarm Indication Signal

TU-LOP

LOP—Tributary Unit—Loss of Pointer

TUNDERRUN

Ethernet Transmit First In First Out Underrun

TX-AIS

Alarm Indication Signal in TX

TX-RAI

Remote Alarm Indication in TX

UNC-WORD

FEC Uncorrected Word

VCG-DEG

VCAT Group Degraded

VCG-DOWN

VCAT Group Down

VOA-HDEG

Variable Optical Attenuator Degrade High

VOA-HFAIL

Variable Optical Attenuator Failure High

VOA-LDEG

Variable Optical Attenuator Degrade Low

VOA-LFAIL

Variable Optical Attenuator Failure Low

WKSWPR

Switched To Protection

WTR

Wait To Restore

WVL-MISMATCH

Equipment Wavelength Mismatch