Cisco ONS SDH TL1 Command Guide, Release 9.4
Chapter 21, RTRV Commands
Downloads: This chapterpdf (PDF - 4.41MB) The complete bookPDF (PDF - 10.93MB) | Feedback

Table of Contents

RTRV Commands

21.1 RTRV-CPS

21.2 RTRV-HOP-CPS

RTRV Commands

This chapter provides retrieve (RTRV) commands for the Cisco ONS 15454 SDH, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.


Note All commands supported on the Cisco ONS 15454 SDH platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.


21.1 RTRV-CPS

This command can be used to retrieve Control Plane Service parameter. The user needs to specify only the source port to identify the CPS. ALL and group AID are allowed.

 
Usage Guidelines

  • If the AID is invalid, an IIAC (invalid AID) error message is returned
  • The ALL AID and group AID are valid for this command
  • In case of ADD 2-WAY with two source AIDs use only one aid to avoid a double response: one for each AID specified
  • CLIENT cps type support FAC and VFAC AID type.
  • TRUNK cps type support CHAN AID type.
  • ADD cps type support CHAN, PCHAN, and LINEWL AID type.
  • In case of 1WAY, unidirectional connection, SRC and DST are single AIDs. In case of 2WAY, bidirectional connection, SRC and DST are double AIDs. However, in case of CLIENT or TRUNK cpstype, src and dst are single AID and the connection is of type 2WAY because of bidirectional ports hence this rule is not applicable.

Category

DWDM

Security

provisioning

Input Format

RTRV-CPS:[<TID>]:<SRC>:<CTAG>::[:CKTID=<CKTID>][:];

Input Example

RTRV-CPS::PCHAN-1-1-RX:8::;

Input Parameters

<SRC>

Source AID from the “CrossConnectId1” section.

<CKTID>

Circuit identification parameter can be used to filter this command

Output Format

SID DATE TIME

M CTAG COMPLD "<SRC>:<DSTADDR>,<DST>,<WCT>,<CPSTYPE>:[CKTID=<CKTID>],VALMODE=<VALMODE>,[VALZONE=<VALZONE>],[VALMODESEC=<VALMODESEC>],[VALZONESEC=<VALZONESEC>],CPSSTATUS=<CPSSTATUS>,ACTVALZONE=<ACTVALZONE>:<PST_PSTQ>,[<SSTQ>]";

Output Example

tcc232 2011-08-05 16:37:44

M 8 COMPLD "PCHAN-1-1-RX&PCHAN-1-1-TX:10.20.30.40,PCHAN-2-2-TX&PCHAN-2-2-RX,2WAY,ADD:CKTID=twoway_add-passive,VALMODE=FULL,VALZONE=RED,CPSSTATUS=INACTIVE,ACTVALZONE=UNKNOWN:OOS-MA,"

;

Output Parameters

<SRC>

Source access identifier from the “ALL” section. Listable.

<DSTADDR>

Identifies the destination node IP address.

<DST>

Destination AID from the “ALL” section.

<WCT>

Identifies the wavelength connection type.

  • 1WAY

A unidirectional connection from a source to a destination port. Deafult is 1WAY

  • 2WAY

A bidirectional connection between the two ports.

<CPSTYPE>

Identifies the type of CPS.

  • CLIENT

CPS End Point are client ports

  • TRUNK

CPS End Point are trunk ports

  • ADD

CPS Source End Point is an ADD port

  • DROP

Not applicable

  • TNA

Not applicable

<CKTID>

(Optional) Circuit identification parameter contains the Common Language Circuit ID or other alias of the circuit being provisioned. Does not contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<VALMODE>

Identifies the validation mode.

  • NONE

No Optical validation is performed.

  • FULL

The optical validation is performed as indicated in VALZONE parameter.

<VALZONE>

Identifies the validation operate zone.

  • UNKNOWN

Not evaluated

  • GREEN

Margin > 3 sigma

  • YELLOW

1 < margin < 3 sigma

  • ORANGE

0 < margin < 1 sigma

  • RED

-3 < margin < 0 sigma

  • OUT

Margin < -3 sigma

CPSSTATUS

Identifies the Control Plane Service status.

  • INACTIVE

CPS is not active

  • ACTIVE

CPS is active

  • ACTIVATING

CPS activation is started

  • DEACTIVATING

CPS deactivation is started

  • FAILED

CPS circuit failed (i.e. link down, node down)

  • DEGRADED

CPS trail failed (i.e. PSM working or protected is down or fail)

  • RECOVERING

temporary reboot status at CPS restart

  • HANDOVER

Not applicable

  • REPAIRING

CPS repair is started (i.e. node IP changed)

ACTVALZONE

Identifies the actual validation operate zone.

  • UNKNOWN

Not evaluated

  • GREEN

Margin > 3 sigma

  • YELLOW

1 < margin < 3 sigma

  • ORANGE

0 < margin < 1 sigma

  • RED

-3 < margin < 0 sigma

  • OUT

Margin < -3 sigma

<VALMODESEC>

Identifies the validation mode for secondary circuit

<VALZONESEC>

Identifies the validation operate zone for secondary circuit

21.2 RTRV-HOP-CPS

( Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Retrieve HOP Control Plane Service (RTRV-HOP-CPS) command is used to retrieve the HOPs route contraint of the Control Plane Services.

 
Usage Guidelines

  • Specify only the source port to identify the CPS.
  • ALL and group AID are allowed.
  • Optional parameters can be used as filter to the command.
  • CLIENT cps type support FAC and VFAC AID type.
  • TRUNK cps type support CHAN AID type.
  • ADD cps type support CHAN, PCHAN, and LINEWL AID type.
  • In case of 1WAY, unidirectional connection, SRC and DST are single AIDs. In case of 2WAY, bidirectional connection, SRC and DST are double AIDs. However, in case of CLIENT or TRUNK cpstype, src and dst are single AID and the connection is of type 2WAY because of bidirectional ports hence this rule is not applicable.

Category

DWDM

Security

Provisioning

Input Format

RTRV-HOP-CPS:[<TID>]:<SRC>:<CTAG>::[<CIRCUITTYPE>],[<ROUTETYPE>],[<HOPTYPE>],[<HOPNODE>],[<HOPSIDE>][::];

Input Example

> RTRV-HOP-CPS::ALL:333;

 

tcc232 2011-08-02 16:27:24

M 333 COMPLD

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,2,LOOSE,10.20.33.45,"

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,3,LOOSE,10.20.33.46,"

"VFAC-1-5-2:10.20.30.40,,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"

;

Input Parameters

<SRC>

Source AID from the “CrossConnectId1” section.

<CIRCUITTYPE>

Identifies the target circuit. Allowed values are PRIMARY, SECONDARY.

<ROUTETYPE>

Identifies the target circuit route. Allowed values are MAINROUTE and BRIDGEROUTE.

<POSITION>

Identifies the position of the hop in the item list. Default value is 0.

  • If action=ADD and position=0 than append at the end;
  • If action=REMOVE and position=0 than remove all matching items;
  • If action=REMOVE and position<>0 than hop values are ignored;
  • If action=MODIFY and position<>0 than replace the item in the position indicated;
  • If action=CLEARALL than clears the list ignoring position and other parameters;

<HOPTYPE>

Type of hop constraint. Allowed values are STRICT, LOOSE, EXCLUDE

  • STRICT

The next hop of the path must be the indicated node and side

  • LOOSE

The path must cross the indicated node and side

  • EXCLUDE

The path must exclude the indicated node

<HOPNODE>

IP address of the target node.

<HOPSIDE>

Hop constraint target WDM side.

Output Format

SID DATE TIME

M CTAG COMPLD

"<SRC>:<DSTADDR>,<DST>,<CIRCUITTYPE>,<ROUTETYPE>,<POSITION><HOPTYPE>,<HOPNODE>,<HOPSIDE>";

Output Example

tcc232 2011-08-02 16:27:24

M 333 COMPLD

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,2,LOOSE,10.20.33.45,"

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,3,LOOSE,10.20.33.46,"

"VFAC-1-5-2:10.20.30.40,,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"

;

tcc232 2011-08-02 16:27:37

M 333 COMPLD

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,1,LOOSE,10.20.33.44,"

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,2,LOOSE,10.20.33.45,"

"CHAN-1-15-10-RX&CHAN-1-14-10-TX:10.20.30.40,CHAN-10-1-10-TX&CHAN-10-1-10-RX,PRIMARY,MAINROUTE,3,LOOSE,10.20.33.46,"

;

Output Parameters

<SRC>

Source access identifier from the “ALL” section. Listable.

<DSTADDR>

Identifies the destination node IP address.

<DST>

Destination AID from the “ALL” section.

<CIRCUITTYPE>

Identifies the target circuit. Allowed values are PRIMARY,SECONDARY.

<ROUTETYPE>

Identifies the target circuit route. Allowed values are MAINROUTE, BRIDGEROUTE.

<POSITION>

Identifies the position of the hop in the item list.

<HOPTYPE>

Type of hop constraint. Allowed values are STRICT, LOOSE, EXCLUDE.

  • STRICT

The next hop of the path must be the indicated node and side.

  • LOOSE

The path must cross the indicated node and side.

  • EXCLUDE

The path must exclude the indicated node.

<HOPNODE>

IP address of the target node.

<HOPSIDE>

Hop constraint target WDM side.

21.3 RTRV-<MOD1FCPAYLOAD>

(Cisco ONS 15454 SDH) The Retrieve 1GFC, 2GFC, 4 GFC, 5GIB, 8GFC, or 10 GFC (RTRV-<MOD1FCPAYLOAD>) command retrieves the attributes related with the Fibre Channel port. SeeTable 27-1 for supported modifiers by platform.

 
Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-1GFC:CISCO:FAC-6-1:888;

Input Parameters

<AID>

Access identifier from the FACILITY.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:,,[<ROLE>],[<STATUS>]:LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>,
[LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>], [SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[SQUELCHMODE=<SQUELCHMODE>]:<PSTPSTQ>,[<SST>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“FAC-1-1:,,WORK,ACT:LINKRATE=1GFC,LINKSTATE=UP,LINKRCVRY=Y,
DISTEXTN=NONE,LINKCREDITS=0,MFS=2148,ENCAP=GFP-T,
NAME=\"FC PORT\",SOAK=32,SOAKLEFT=\"12-25\",FREQ=1550,
LOSSB=LR-1:LOCKED-ENABLED,MAINTENANCE”,
SQUELCHMODE=SQUELCH:OOS-MA,DSBLD"
;

 

Table 21-1 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “FACILITY” section.

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.

  • PROT

The entity is a protection unit in the protection group.

  • WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) The port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

  • ACT

The entity is the active unit in the shelf.

  • NA

Status is unavailable.

  • STBY

The entity is the standby unit in the shelf.

<LINKRATE>

(Optional) The actual rate running on the Fibre Channel port. It can differ from the payload type provisioned. The parameter type is LINKRATE, which is the link rate on a Fibre Channel port.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • UNKNOWN

The rate is unknown.

  • UNPLUGGED

The Small Form-factor Pluggable (SFP) is not plugged into the Fibre Channel port so the link rate cannot be detected.

<LINKSTATE>

(Optional) Link state. The parameter type is DIRN, which specifies the discriminating level for the requested monitored parameter.

  • DN

Monitored parameter with values equal to or greater than the level of LEV will be reported.

  • UP

Monitored parameter with values equal or less than the value of LEV will be reported.

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

<DISTEXTN>

(Optional) Distance extension. The parameter type is DISTANCE_EXTENSION (distance extension)

  • B2B

Buffer to buffer flow control

  • NONE

No distance extension

LINKCREDITS

(Optional) Number of link credits. LINKCREDITS is an integer.

MFS

(Optional) Maximum frame size. MFS is an integer.

ENCAP

(Optional) Frame encapsulation type. The parameter type is ENCAP, which is the frame encapsulation type.

  • GFP_F

Generic framing procedure (GFP) frame mode

  • GFP_T

GFP transparent mode

  • HDLC

High-level data link control (HDLC) frame mode

  • HDLC_LEX

HDLC LAN extension frame mode

  • HDLC_X86

HDLC X.86 frame mode

<NAME>

(Optional) Identifies the port name. NAME is a string.

<SOAK>

(Optional) Locked-Automatic In Service to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.

<SOAKLEFT>

(Optional) Time remaining for the transition from Locked-Automatic In Service to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. The rules for SOAKLEFT are:

  • When the port is in Locked, Locked_Maintenance or Unlocked state, the parameter will not appear.
  • When the port is in Locked_AutomaticInService but the countdown has not started due to fault signal, the value will be SOAKLEFT=NOT-STARTED.
  • When the port is in Locked_AutomaticInService state and the countdown has started, the value will be shown in HH-MM format.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

  • 1310

Wavelength 1310

  • 1470

Wavelength 1470

  • 1490

Wavelength 1490

  • 1510

Wavelength 1510

  • 1528.77

Wavelength 1528.77

  • 1529.55

Wavelength 1529.55

  • 1529.94

Wavelength 1529.94

  • 1530

Wavelength 1530

  • 1530.33

Wavelength 1530.33

  • 1530.73

Wavelength 1530.73

  • 1531.12

Wavelength 1531.12

  • 1531.51

Wavelength 1531.51

  • 1531.90

Wavelength 1531.90

  • 1532.29

Wavelength 1532.29

  • 1532.68

Wavelength 1532.68

  • 1533.07

Wavelength 1533.07

  • 1533.47

Wavelength 1533.47

  • 1533.86

Wavelength 1533.86

  • 1534.25

Wavelength 1534.25

  • 1534.64

Wavelength 1534.64

  • 1535.04

Wavelength 1535.04

  • 1535.43

Wavelength 1535.43

  • 1535.82

Wavelength 1535.82

  • 1536.22

Wavelength 1536.22

  • 1536.61

Wavelength 1536.61

  • 1537

Wavelength 1537

  • 1537.40

Wavelength 1537.40

  • 1537.79

Wavelength 1537.79

  • 1538.19

Wavelength 1538.19

  • 1538.58

Wavelength 1538.58

  • 1538.98

Wavelength 1538.98

  • 1539.37

Wavelength 1539.37

  • 1539.77

Wavelength 1539.77

  • 1540.16

Wavelength 1540.16

  • 1540.56

Wavelength 1540.56

  • 1540.95

Wavelength 1540.95

  • 1541.35

Wavelength 1541.35

  • 1541.75

Wavelength 1541.75

  • 1542.14

Wavelength 1542.14

  • 1542.35

Wavelength 1542.35

  • 1542.54

Wavelength 1542.54

  • 1542.94

Wavelength 1542.94

  • 1543.33

Wavelength 1543.33

  • 1543.73

Wavelength 1543.73

  • 1544.13

Wavelength 1544.13

  • 1544.53

Wavelength 1544.53

  • 1544.92

Wavelength 1544.92

  • 1545.32

Wavelength 1545.32

  • 1545.72

Wavelength 1545.72

  • 1546.12

Wavelength 1546.12

  • 1546.52

Wavelength 1546.52

  • 1546.92

Wavelength 1546.92

  • 1547.32

Wavelength 1547.32

  • 1547.72

Wavelength 1547.72

  • 1548.12

Wavelength 1548.12

  • 1548.51

Wavelength 1548.51

  • 1548.92

Wavelength 1548.92

  • 1549.32

Wavelength 1549.32

  • 1549.71

Wavelength 1549.71

  • 1550

Wavelength 1500

  • 1550.12

Wavelength 1550.12

  • 1550.52

Wavelength 1550.52

  • 1550.92

Wavelength 1550.92

  • 1551.32

Wavelength 1551.32

  • 1551.72

Wavelength 1551.72

  • 1552.12

Wavelength 1552.12

  • 1552.52

Wavelength 1552.52

  • 1552.93

Wavelength 1552.93

  • 1553.33

Wavelength 1553.33

  • 1553.73

Wavelength 1553.73

  • 1554.13

Wavelength 1554.13

  • 1554.13

Wavelength 1554.13

  • 1554.94

Wavelength 1554.94

  • 1555.34

Wavelength 1555.34

  • 1555.75

Wavelength 1555.75

  • 1556.15

Wavelength 1556.15

  • 1556.55

Wavelength 1556.55

  • 1556.96

Wavelength 1556.96

  • 1557.36

Wavelength 1557.36

  • 1557.77

Wavelength 1557.77

  • 1558.17

Wavelength 1558.17

  • 1558.58

Wavelength 1558.58

  • 1558.98

Wavelength 1558.98

  • 1559.39

Wavelength 1559.39

  • 1559.79

Wavelength 1559.79

  • 1560.20

Wavelength 1560.20

  • 1560.61

Wavelength 1560.61

  • 1561.01

Wavelength 1561.01

  • 1561.42

Wavelength 1561.42

  • 1561.83

Wavelength 1561.83

  • 1570

Wavelength 1570

  • 1570.83

Wavelength 1570.83

  • 1571.24

Wavelength 1571.24

  • 1571.65

Wavelength 1571.65

  • 1572.06

Wavelength 1572.06

  • 1572.48

Wavelength 1572.48

  • 1572.89

Wavelength 1572.89

  • 1573.30

Wavelength 1573.30

  • 1573.71

Wavelength 1573.71

  • 1574.13

Wavelength 1574.13

  • 1574.54

Wavelength 1574.54

  • 1574.95

Wavelength 1574.95

  • 1575.37

Wavelength 1575.37

  • 1575.78

Wavelength 1575.78

  • 1576.20

Wavelength 1576.20

  • 1576.61

Wavelength 1576.61

  • 1577.03

Wavelength 1577.03

  • 1577.44

Wavelength 1577.44

  • 1577.86

Wavelength 1577.86

  • 1578.27

Wavelength 1578.27

  • 1578.69

Wavelength 1578.69

  • 1579.10

Wavelength 1579.10

  • 1579.52

Wavelength 1579.52

  • 1579.93

Wavelength 1579.93

  • 1580.35

Wavelength 1580.35

  • 1580.77

Wavelength 1580.77

  • 1581.18

Wavelength 1581.18

  • 1581.60

Wavelength 1581.60

  • 1582.02

Wavelength 1582.02

  • 1582.44

Wavelength 1582.44

  • 1582.85

Wavelength 1582.85

  • 1583.27

Wavelength 1583.27

  • 1583.69

Wavelength 1583.69

  • 1584.11

Wavelength 1584.11

  • 1584.53

Wavelength 1584.53

  • 1584.95

Wavelength 1584.95

  • 1585.36

Wavelength 1585.36

  • 1585.78

Wavelength 1585.78

  • 1586.20

Wavelength 1586.20

  • 1586.62

Wavelength 1586.62

  • 1587.04

Wavelength 1587.04

  • 1587.46

Wavelength 1587.46

  • 1587.88

Wavelength 1587.88

  • 1588.30

Wavelength 1588.30

  • 1588.73

Wavelength 1588.73

  • 1589.15

Wavelength 1589.15

  • 1589.57

Wavelength 1589.57

  • 1589.99

Wavelength 1589.99

  • 1590

Wavelength 1590

  • 1590.41

Wavelength 1590.41

  • 1590.83

Wavelength 1590.83

  • 1591.26

Wavelength 1591.26

  • 1591.68

Wavelength 1591.68

  • 1592.10

Wavelength 1592.10

  • 1592.52

Wavelength 1592.52

  • 1592.95

Wavelength 1592.95

  • 1593.37

Wavelength 1593.37

  • 1593.79

Wavelength 1593.79

  • 1594.22

Wavelength 1594.22

  • 1594.64

Wavelength 1594.64

  • 1595.06

Wavelength 1595.06

  • 1595.49

Wavelength 1595.49

  • 1596.34

Wavelength 1596.34

  • 1596.76

Wavelength 1596.76

  • 1597.19

Wavelength 1597.19

  • 1597.62

Wavelength 1597.62

  • 1598.04

Wavelength 1598.04

  • 1598.47

Wavelength 1598.47

  • 1598.89

Wavelength 1598.89

  • 1599.32

Wavelength 1599.32

  • 1599.75

Wavelength 1599.75

  • 1600.06

Wavelength 1600.06

  • 1601.03

Wavelength 1601.03

  • 1601.46

Wavelength 1601.46

  • 1601.88

Wavelength 1601.88

  • 1602.31

Wavelength 1602.31

  • 1602.74

Wavelength 1602.74

  • 1603.17

Wavelength 1603.17

  • 1603.60

Wavelength 1603.60

  • 1604.03

Wavelength 1604.03

  • 1610

Wavelength 1610

  • USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

The parameter type is REACH, which is the reach value.

  • AUTOPROV

Autoprovisioning

  • CX

Reach CX

  • CX1

Reach CX1

  • DX

Reach DX

  • HX

Reach HX

  • I1

Reach I1

  • IR-1

Reach IR-1

  • IR-2

Reach IR-2

  • L1

Reach L1

  • L2

Reach L2

  • L3

Reach L3

  • LR-1

Reach LR-1

  • LR-2

Reach LR-2

  • LR-3

Reach LR-3

  • LX

Reach LX

  • S1

Reach S1

  • S2

Reach S2

  • SR

Reach SR

  • SR-1

Reach SR-1

  • SX

Reach SX

  • T

Reach T

  • TEN-GE-ER

10 GE extended range

  • TEN-GE-LR

10 GE long range

  • TEN-GE-SR

10 GE short range

  • VX

Reach VX

  • ZX

Reach ZX

<SQUELCHMODE>

Shuts down the far-end laser in response to certain defects.

  • SQUELCH

Squelch is enabled.

  • NONE

No Squelch.

  • NOS

Squelch is disabled.

<PSTPSTQ>

Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the primary state (PST) and primary state qualifier (PSTQ).

  • Unlocked-Enabled

In service and normal

  • Unlocked-Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SST>

(Optional) Secondary state of the entity. The parameter type is secondary state (SST), which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.4 RTRV-<MOD1FICONPAYLOAD>

(Cisco ONS 15454 SDH) The Retrieve 1GFICON, 2GFICON, or 4GFICON (RTRV-MOD1FICONPAYLOAD>) command returns Fibre-Channel-specific settings for ports that have been configured to carry fiber connectivity (FICON) traffic using the ENT-FICON command. The MXP_MR_2.5G and MXPP_MR_2.5G cards only support the GFP-T frame type. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-1GFICON:CISCO:FAC-1-1:123;

Input Parameters

<AID>

Access identifier from the “FACILITY” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:,,[<ROLE>],[<STATUS>]:[LINKRATE=<LINKRATE>],[LINKSTATE=<LINKSTATE>],
[LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>],
[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,<SST>”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“FAC-1-1:,,WORK,ACT:LINKRATE=1GFICON,LINKSTATE=UP,LINKRCVRY=Y,
DISTEXTN=NONE,LINKCREDITS=0,MFS=2148,ENCAP=GFP-T,NAME=\"FC PORT\",
SOAK=32,SOAKLEFT=\"12-25\",FREQ=1550,LOSSB=LR-1:LOCKED-ENABLED,
MAINTENANCE”
;

 

Table 21-2 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “FACILITY” section.

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.

  • PROT

The entity is a protection unit in the protection group.

  • WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

  • ACT

The entity is the active unit in the shelf.

  • NA

Status is unavailable.

  • STBY

The entity is the standby unit in the shelf.

<LINKRATE>

(Optional) The actual rate running on the Fibre Channel port. It can differ from the payload type provisioned. The parameter type is LINKRATE, which is the link rate on a Fibre Channel port.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • UNKNOWN

The rate is unknown.

  • UNPLUGGED

The SFP is not plugged into the Fibre Channel port, so the link rate cannot be detected.

<LINKSTATE>

(Optional) Link state. The parameter type is DIRN, which specifies the discriminating level for the requested monitored parameter.

  • DN

Monitored parameter with values equal to or greater than the level of LEV will be reported.

  • UP

Monitored parameter with values equal or less than the value of LEV will be reported.

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

<DISTEXTN>

(Optional) Distance extension. The parameter type is DISTANCE_EXTENSION (distance extension).

  • B2B

Buffer-to-buffer flow control

  • NONE

No distance extension

<LINKCREDITS>

(Optional) Number of link credits. LINKCREDITS is an integer.

<MFS>

(Optional) Maximum frame size. MFS is an integer.

<ENCAP>

(Optional) Frame encapsulation type. The parameter type is ENCAP, which is the frame encapsulation type.

  • GFP_F

GFP frame mode

  • GFP_T

GFP transparent mode

  • HDLC

HDLC frame mode

  • HDLC_LEX

HDLC LAN extension frame mode

  • HDLC_X86

HDLC X.86 frame mode

<NAME>

(Optional) Identifies the port name. NAME is a string.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.

<SOAKLEFT>

(Optional) Time remaining for the transition from Locked-AutomaticInService to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. Rules for <SOAKLEFT> are:

  • When the port is in Locked, Locked_Maintenance or Unlocked state, the parameter will not appear.
  • When the port is in Locked_AutomaticInService, but the countdown has not started due to fault signal, the value will be SOAKLEFT=NOT-STARTED.
  • When the port is in Locked_AutomaticInService state and the countdown has started, the value will be shown in HH-MM format.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

  • 1310

Wavelength 1310

  • 1470

Wavelength 1470

  • 1490

Wavelength 1490

  • 1510

Wavelength 1510

  • 1528.77

Wavelength 1528.77

  • 1529.55

Wavelength 1529.55

  • 1529.94

Wavelength 1529.94

  • 1530

Wavelength 1530

  • 1530.33

Wavelength 1530.33

  • 1530.73

Wavelength 1530.73

  • 1531.12

Wavelength 1531.12

  • 1531.51

Wavelength 1531.51

  • 1531.90

Wavelength 1531.90

  • 1532.29

Wavelength 1532.29

  • 1532.68

Wavelength 1532.68

  • 1533.07

Wavelength 1533.07

  • 1533.47

Wavelength 1533.47

  • 1533.86

Wavelength 1533.86

  • 1534.25

Wavelength 1534.25

  • 1534.64

Wavelength 1534.64

  • 1535.04

Wavelength 1535.04

  • 1535.43

Wavelength 1535.43

  • 1535.82

Wavelength 1535.82

  • 1536.22

Wavelength 1536.22

  • 1536.61

Wavelength 1536.61

  • 1537

Wavelength 1537

  • 1537.40

Wavelength 1537.40

  • 1537.79

Wavelength 1537.79

  • 1538.19

Wavelength 1538.19

  • 1538.58

Wavelength 1538.58

  • 1538.98

Wavelength 1538.98

  • 1539.37

Wavelength 1539.37

  • 1539.77

Wavelength 1539.77

  • 1540.16

Wavelength 1540.16

  • 1540.56

Wavelength 1540.56

  • 1540.95

Wavelength 1540.95

  • 1541.35

Wavelength 1541.35

  • 1541.75

Wavelength 1541.75

  • 1542.14

Wavelength 1542.14

  • 1542.35

Wavelength 1542.35

  • 1542.54

Wavelength 1542.54

  • 1542.94

Wavelength 1542.94

  • 1543.33

Wavelength 1543.33

  • 1543.73

Wavelength 1543.73

  • 1544.13

Wavelength 1544.13

  • 1544.53

Wavelength 1544.53

  • 1544.92

Wavelength 1544.92

  • 1545.32

Wavelength 1545.32

  • 1545.72

Wavelength 1545.72

  • 1546.12

Wavelength 1546.12

  • 1546.52

Wavelength 1546.52

  • 1546.92

Wavelength 1546.92

  • 1547.32

Wavelength 1547.32

  • 1547.72

Wavelength 1547.72

  • 1548.12

Wavelength 1548.12

  • 1548.51

Wavelength 1548.51

  • 1548.92

Wavelength 1548.92

  • 1549.32

Wavelength 1549.32

  • 1549.71

Wavelength 1549.71

  • 1550

Wavelength 1500

  • 1550.12

Wavelength 1550.12

  • 1550.52

Wavelength 1550.52

  • 1550.92

Wavelength 1550.92

  • 1551.32

Wavelength 1551.32

  • 1551.72

Wavelength 1551.72

  • 1552.12

Wavelength 1552.12

  • 1552.52

Wavelength 1552.52

  • 1552.93

Wavelength 1552.93

  • 1553.33

Wavelength 1553.33

  • 1553.73

Wavelength 1553.73

  • 1554.13

Wavelength 1554.13

  • 1554.13

Wavelength 1554.13

  • 1554.94

Wavelength 1554.94

  • 1555.34

Wavelength 1555.34

  • 1555.75

Wavelength 1555.75

  • 1556.15

Wavelength 1556.15

  • 1556.55

Wavelength 1556.55

  • 1556.96

Wavelength 1556.96

  • 1557.36

Wavelength 1557.36

  • 1557.77

Wavelength 1557.77

  • 1558.17

Wavelength 1558.17

  • 1558.58

Wavelength 1558.58

  • 1558.98

Wavelength 1558.98

  • 1559.39

Wavelength 1559.39

  • 1559.79

Wavelength 1559.79

  • 1560.20

Wavelength 1560.20

  • 1560.61

Wavelength 1560.61

  • 1561.01

Wavelength 1561.01

  • 1561.42

Wavelength 1561.42

  • 1561.83

Wavelength 1561.83

  • 1570

Wavelength 1570

  • 1570.83

Wavelength 1570.83

  • 1571.24

Wavelength 1571.24

  • 1571.65

Wavelength 1571.65

  • 1572.06

Wavelength 1572.06

  • 1572.48

Wavelength 1572.48

  • 1572.89

Wavelength 1572.89

  • 1573.30

Wavelength 1573.30

  • 1573.71

Wavelength 1573.71

  • 1574.13

Wavelength 1574.13

  • 1574.54

Wavelength 1574.54

  • 1574.95

Wavelength 1574.95

  • 1575.37

Wavelength 1575.37

  • 1575.78

Wavelength 1575.78

  • 1576.20

Wavelength 1576.20

  • 1576.61

Wavelength 1576.61

  • 1577.03

Wavelength 1577.03

  • 1577.44

Wavelength 1577.44

  • 1577.86

Wavelength 1577.86

  • 1578.27

Wavelength 1578.27

  • 1578.69

Wavelength 1578.69

  • 1579.10

Wavelength 1579.10

  • 1579.52

Wavelength 1579.52

  • 1579.93

Wavelength 1579.93

  • 1580.35

Wavelength 1580.35

  • 1580.77

Wavelength 1580.77

  • 1581.18

Wavelength 1581.18

  • 1581.60

Wavelength 1581.60

  • 1582.02

Wavelength 1582.02

  • 1582.44

Wavelength 1582.44

  • 1582.85

Wavelength 1582.85

  • 1583.27

Wavelength 1583.27

  • 1583.69

Wavelength 1583.69

  • 1584.11

Wavelength 1584.11

  • 1584.53

Wavelength 1584.53

  • 1584.95

Wavelength 1584.95

  • 1585.36

Wavelength 1585.36

  • 1585.78

Wavelength 1585.78

  • 1586.20

Wavelength 1586.20

  • 1586.62

Wavelength 1586.62

  • 1587.04

Wavelength 1587.04

  • 1587.46

Wavelength 1587.46

  • 1587.88

Wavelength 1587.88

  • 1588.30

Wavelength 1588.30

  • 1588.73

Wavelength 1588.73

  • 1589.15

Wavelength 1589.15

  • 1589.57

Wavelength 1589.57

  • 1589.99

Wavelength 1589.99

  • 1590

Wavelength 1590

  • 1590.41

Wavelength 1590.41

  • 1590.83

Wavelength 1590.83

  • 1591.26

Wavelength 1591.26

  • 1591.68

Wavelength 1591.68

  • 1592.10

Wavelength 1592.10

  • 1592.52

Wavelength 1592.52

  • 1592.95

Wavelength 1592.95

  • 1593.37

Wavelength 1593.37

  • 1593.79

Wavelength 1593.79

  • 1594.22

Wavelength 1594.22

  • 1594.64

Wavelength 1594.64

  • 1595.06

Wavelength 1595.06

  • 1595.49

Wavelength 1595.49

  • 1596.34

Wavelength 1596.34

  • 1596.76

Wavelength 1596.76

  • 1597.19

Wavelength 1597.19

  • 1597.62

Wavelength 1597.62

  • 1598.04

Wavelength 1598.04

  • 1598.47

Wavelength 1598.47

  • 1598.89

Wavelength 1598.89

  • 1599.32

Wavelength 1599.32

  • 1599.75

Wavelength 1599.75

  • 1600.06

Wavelength 1600.06

  • 1601.03

Wavelength 1601.03

  • 1601.46

Wavelength 1601.46

  • 1601.88

Wavelength 1601.88

  • 1602.31

Wavelength 1602.31

  • 1602.74

Wavelength 1602.74

  • 1603.17

Wavelength 1603.17

  • 1603.60

Wavelength 1603.60

  • 1604.03

Wavelength 1604.03

  • 1610

Wavelength 1610

  • USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

  • AUTOPROV

Autoprovisioning

  • CX

Reach CX

  • CX1

Reach CX1

  • DX

Reach DX

  • HX

Reach HX

  • I1

Reach I1

  • IR-1

Reach IR-1

  • IR-2

Reach IR-2

  • L1

Reach L1

  • L2

Reach L2

  • L3

Reach L3

  • LR-1

Reach LR-1

  • LR-2

Reach LR-2

  • LR-3

Reach LR-3

  • LX

Reach LX

  • S1

Reach S1

  • S2

Reach S2

  • SR

Reach SR

  • SR-1

Reach SR-1

  • SX

Reach SX

  • T

Reach T

  • TEN-GE-ER

10 GE extended range

  • TEN-GE-LR

10 GE long range

  • TEN-GE-SR

10 GE short range

  • VX

Reach VX

  • ZX

Reach ZX

<PSTPSTQ>

Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked-Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SST>

Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.5 RTRV-<MOD2DWDMPAYLOAD>

(Cisco ONS 15454 SDH) The Retrieve D1VIDEO, DV6000, DVBASI, ETRCLO, HDTV, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, PASSTHRU, 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G (RTRV-<MOD2DWDMPAYLOAD>) command retrieves the configuration parameter of a dense wavelength division multiplexing (DWDM) client. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

The command supports the modifier 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G.

Category

Ports

Security

Maintenance

Input Format

RTRV-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-SDSDI::VFAC-3-2-1:321;

Input Parameters

<AID>

Access identifier from the “FACILITY” section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.

Output Format

SID DATE TIME M CTAG COMPLD "<AIDUNIONID>,<AIDTYPE>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],[LBCL=<LBCL>], [OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],[SQUELCHMODE=,SQUELCHMODE.]:<PSTPSTQ>,[<SST>]" ;

Output Example

TID-000 1998-06-20 14:30:00

M 321 COMPLD

"VFAC-3-2-1,SDSDI:,,WORK,ACT:NAME=\"NY PORT\",LBCL=10.0,OPT=10.0,OPR=10.0, FREQ=1550,LOSSB=LR-1,SQUELCHMODE=SQUELCH:OOS-AU,AINS" ;

 

Table 21-3 Output Parameter Support

Parameter
Description

<AIDUNIONID>

Access identifier from the “AidUnionId” section.

<AIDTYPE>

A type of access identifier. The parameter type is MOD2DWDMPAYLOAD, which is the payload types applicable to DWDM ports.

  • 10GFC

10-Gigabit Fibre Channel payload

  • 10GIGE

10-Gigabit Ethernet

  • 40GIGE

40-Gigabit Ethernet

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • D1VIDEO

D1Video payload

  • DV6000

DV6000 payload

  • DVBASI

DVBASI payload

  • ETRCLO

ETRCLO payload

  • GIGE

Gigabit Ethernet payload

  • HDTV

HDTV payload

  • ISC1

ISC1 payload

  • ISC3

ISC3 payload

  • PASSTHRU

Any pass-through (2R) payload

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit has in the protection group.

  • PROT

The entity is a protection unit in the protection group.

  • WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

  • ACT

The entity is the active unit in the shelf.

  • NA

Status is unavailable.

  • STBY

The entity is the standby unit in the shelf.

<NAME>

(Optional) Identifies the port name. NAME is a string.

<LBCL>

(Optional) Displays the current value of the laser current. LBCL is a float.

<OPT>

(Optional) Displays the current value of the transmitted optical power. OPT is a float.

<OPR>

(Optional) Displays the current value of the received optical power. OPR is a float.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

  • 1310

Wavelength 1310

  • 1470

Wavelength 1470

  • 1490

Wavelength 1490

  • 1510

Wavelength 1510

  • 1528.77

Wavelength 1528.77

  • 1529.55

Wavelength 1529.55

  • 1529.94

Wavelength 1529.94

  • 1530

Wavelength 1530

  • 1530.33

Wavelength 1530.33

  • 1530.73

Wavelength 1530.73

  • 1531.12

Wavelength 1531.12

  • 1531.51

Wavelength 1531.51

  • 1531.90

Wavelength 1531.90

  • 1532.29

Wavelength 1532.29

  • 1532.68

Wavelength 1532.68

  • 1533.07

Wavelength 1533.07

  • 1533.47

Wavelength 1533.47

  • 1533.86

Wavelength 1533.86

  • 1534.25

Wavelength 1534.25

  • 1534.64

Wavelength 1534.64

  • 1535.04

Wavelength 1535.04

  • 1535.43

Wavelength 1535.43

  • 1535.82

Wavelength 1535.82

  • 1536.22

Wavelength 1536.22

  • 1536.61

Wavelength 1536.61

  • 1537

Wavelength 1537

  • 1537.40

Wavelength 1537.40

  • 1537.79

Wavelength 1537.79

  • 1538.19

Wavelength 1538.19

  • 1538.58

Wavelength 1538.58

  • 1538.98

Wavelength 1538.98

  • 1539.37

Wavelength 1539.37

  • 1539.77

Wavelength 1539.77

  • 1540.16

Wavelength 1540.16

  • 1540.56

Wavelength 1540.56

  • 1540.95

Wavelength 1540.95

  • 1541.35

Wavelength 1541.35

  • 1541.75

Wavelength 1541.75

  • 1542.14

Wavelength 1542.14

  • 1542.35

Wavelength 1542.35

  • 1542.54

Wavelength 1542.54

  • 1542.94

Wavelength 1542.94

  • 1543.33

Wavelength 1543.33

  • 1543.73

Wavelength 1543.73

  • 1544.13

Wavelength 1544.13

  • 1544.53

Wavelength 1544.53

  • 1544.92

Wavelength 1544.92

  • 1545.32

Wavelength 1545.32

  • 1545.72

Wavelength 1545.72

  • 1546.12

Wavelength 1546.12

  • 1546.52

Wavelength 1546.52

  • 1546.92

Wavelength 1546.92

  • 1547.32

Wavelength 1547.32

  • 1547.72

Wavelength 1547.72

  • 1548.12

Wavelength 1548.12

  • 1548.51

Wavelength 1548.51

  • 1548.92

Wavelength 1548.92

  • 1549.32

Wavelength 1549.32

  • 1549.71

Wavelength 1549.71

  • 1550

Wavelength 1500

  • 1550.12

Wavelength 1550.12

  • 1550.52

Wavelength 1550.52

  • 1550.92

Wavelength 1550.92

  • 1551.32

Wavelength 1551.32

  • 1551.72

Wavelength 1551.72

  • 1552.12

Wavelength 1552.12

  • 1552.52

Wavelength 1552.52

  • 1552.93

Wavelength 1552.93

  • 1553.33

Wavelength 1553.33

  • 1553.73

Wavelength 1553.73

  • 1554.13

Wavelength 1554.13

  • 1554.13

Wavelength 1554.13

  • 1554.94

Wavelength 1554.94

  • 1555.34

Wavelength 1555.34

  • 1555.75

Wavelength 1555.75

  • 1556.15

Wavelength 1556.15

  • 1556.55

Wavelength 1556.55

  • 1556.96

Wavelength 1556.96

  • 1557.36

Wavelength 1557.36

  • 1557.77

Wavelength 1557.77

  • 1558.17

Wavelength 1558.17

  • 1558.58

Wavelength 1558.58

  • 1558.98

Wavelength 1558.98

  • 1559.39

Wavelength 1559.39

  • 1559.79

Wavelength 1559.79

  • 1560.20

Wavelength 1560.20

  • 1560.61

Wavelength 1560.61

  • 1561.01

Wavelength 1561.01

  • 1561.42

Wavelength 1561.42

  • 1561.83

Wavelength 1561.83

  • 1570

Wavelength 1570

  • 1570.83

Wavelength 1570.83

  • 1571.24

Wavelength 1571.24

  • 1571.65

Wavelength 1571.65

  • 1572.06

Wavelength 1572.06

  • 1572.48

Wavelength 1572.48

  • 1572.89

Wavelength 1572.89

  • 1573.30

Wavelength 1573.30

  • 1573.71

Wavelength 1573.71

  • 1574.13

Wavelength 1574.13

  • 1574.54

Wavelength 1574.54

  • 1574.95

Wavelength 1574.95

  • 1575.37

Wavelength 1575.37

  • 1575.78

Wavelength 1575.78

  • 1576.20

Wavelength 1576.20

  • 1576.61

Wavelength 1576.61

  • 1577.03

Wavelength 1577.03

  • 1577.44

Wavelength 1577.44

  • 1577.86

Wavelength 1577.86

  • 1578.27

Wavelength 1578.27

  • 1578.69

Wavelength 1578.69

  • 1579.10

Wavelength 1579.10

  • 1579.52

Wavelength 1579.52

  • 1579.93

Wavelength 1579.93

  • 1580.35

Wavelength 1580.35

  • 1580.77

Wavelength 1580.77

  • 1581.18

Wavelength 1581.18

  • 1581.60

Wavelength 1581.60

  • 1582.02

Wavelength 1582.02

  • 1582.44

Wavelength 1582.44

  • 1582.85

Wavelength 1582.85

  • 1583.27

Wavelength 1583.27

  • 1583.69

Wavelength 1583.69

  • 1584.11

Wavelength 1584.11

  • 1584.53

Wavelength 1584.53

  • 1584.95

Wavelength 1584.95

  • 1585.36

Wavelength 1585.36

  • 1585.78

Wavelength 1585.78

  • 1586.20

Wavelength 1586.20

  • 1586.62

Wavelength 1586.62

  • 1587.04

Wavelength 1587.04

  • 1587.46

Wavelength 1587.46

  • 1587.88

Wavelength 1587.88

  • 1588.30

Wavelength 1588.30

  • 1588.73

Wavelength 1588.73

  • 1589.15

Wavelength 1589.15

  • 1589.57

Wavelength 1589.57

  • 1589.99

Wavelength 1589.99

  • 1590

Wavelength 1590

  • 1590.41

Wavelength 1590.41

  • 1590.83

Wavelength 1590.83

  • 1591.26

Wavelength 1591.26

  • 1591.68

Wavelength 1591.68

  • 1592.10

Wavelength 1592.10

  • 1592.52

Wavelength 1592.52

  • 1592.95

Wavelength 1592.95

  • 1593.37

Wavelength 1593.37

  • 1593.79

Wavelength 1593.79

  • 1594.22

Wavelength 1594.22

  • 1594.64

Wavelength 1594.64

  • 1595.06

Wavelength 1595.06

  • 1595.49

Wavelength 1595.49

  • 1596.34

Wavelength 1596.34

  • 1596.76

Wavelength 1596.76

  • 1597.19

Wavelength 1597.19

  • 1597.62

Wavelength 1597.62

  • 1598.04

Wavelength 1598.04

  • 1598.47

Wavelength 1598.47

  • 1598.89

Wavelength 1598.89

  • 1599.32

Wavelength 1599.32

  • 1599.75

Wavelength 1599.75

  • 1600.06

Wavelength 1600.06

  • 1601.03

Wavelength 1601.03

  • 1601.46

Wavelength 1601.46

  • 1601.88

Wavelength 1601.88

  • 1602.31

Wavelength 1602.31

  • 1602.74

Wavelength 1602.74

  • 1603.17

Wavelength 1603.17

  • 1603.60

Wavelength 1603.60

  • 1604.03

Wavelength 1604.03

  • 1610

Wavelength 1610

  • USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

  • AUTOPROV

Autoprovisioning

  • CX

Reach CX

  • CX1

Reach CX1

  • DX

Reach DX

  • HX

Reach HX

  • I1

Reach I1

  • IR-1

Reach IR-1

  • IR-2

Reach IR-2

  • L1

Reach L1

  • L2

Reach L2

  • L3

Reach L3

  • LR-1

Reach LR-1

  • LR-2

Reach LR-2

  • LR-3

Reach LR-3

  • LX

Reach LX

  • S1

Reach S1

  • S2

Reach S2

  • SR

Reach SR

  • SR-1

Reach SR-1

  • SX

Reach SX

  • T

Reach T

  • TEN-GE-ER

10 GE extended range

  • TEN-GE-LR

10 GE long range

  • TEN-GE-SR

10 GE short range

  • VX

Reach VX

  • ZX

Reach ZX

<SQUELCHMODE>

Shuts down the far-end laser in response to certain defects.

  • SQUELCH

Squelch is enabled.

  • NONE

No Squelch.

  • ODU-AIS

ODU AIS.

<PSTPSTQ>

Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked-Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SST>

(Optional) Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.6 RTRV-<MOD_RING>

(Cisco ONS 15454 SDH) The Retrieve Multiplex Section Shared Protection Ring (RTRV-<MOD_RING>) command retrieves the multiplex section-shared protection ring (MS-SPRing) information of the network element (NE). A two-fiber or four-fiber MS-SPRing can be retrieved.

 
Usage Guidelines

Error conditions:

  • Only ALL, NULL, MSSPR-ALL, or MSSPR-RINGID is allowed for this command.
  • A NULL AID defaults to the AID ALL.
  • The list AID format is supported.
  • If the system fails on getting information object repository (IOR), a Get IOR Failed (SROF) error message is returned.
  • If the AID is invalid, an Invalid AID (IIAC) error message is returned.
  • If the MS-SPRing does not exist, a MSSPR Does Not Exist (SRQN) error message is returned.

Category

MS-SPRing

Security

Retrieve

Input Format

RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::];

Input Example

RTRV-MSSPR:PETALUMA:ALL:123;

Input Parameters

<AID>

(Optional) Access identifier from the “AidUnionId1” section. Identifies the MS-SPRing of the NE. Only ALL, null or a list of MSSPR-# in AID are allowed. A null value is equivalent to ALL.

Output Format

SID DATE TIME
M CTAG COMPLD
“[<AID>]::[RINGID=<RINGID>],[NODEID=<NODEID>],[MODE=<MODE>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>],
[EASTWORK=<EASTWORK>],[WESTWORK=<WESTWORK>],[EASTPROT=<EASTPROT>],
[WESTPROT=<WESTPROT>]”
;

Output Example

  • 4F MS-SPRing

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“MSSPR-43::RINGID=43,NODEID=3,MODE=4F,RVRTV=Y,RVTM=5.0,
SRVRTV=Y,SRVTM=5.0,EASTWORK=FAC-5-1,WESTWORK=FAC-6-1,
EASTPROT=FAC-12-1,WESTPROT=FAC-13-1”
;

  • 2F MS-SPRing

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“MSSPR-N12EF::RINGID=N12EF,NODEID=2,MODE=2F,RVRTV=Y,RVTM=5.0,
EASTWORK=FAC-5-1,WESTWORK=FAC-6-1”
;

 

Table 21-4 Output Parameter Support

Parameter
Description

<AID>

(Optional) Access identifier from the “AidUnionId1” section. Identifies the MS-SPRing of the NE.

<RINGID>

(Optional) The MS-SPRing ID of the NE up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.

<NODEID>

(Optional) The MS-SPRing node ID of the NE. NODEID ranges from 0 to 31. NODEID is a string.

<MODE>

(Optional) Mode with which the command is to be implemented. Identifies the MS-SPRing mode; either two-fiber or four-fiber. The parameter type is MSSPR_MODE, which is the MS-SPRing mode.

  • 2F

Two-fiber MS-SPRing

  • 4F

Four-fiber MS-SPRing

<RVRTV>

(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Does not revert service to original line after restoration.

  • Y

Reverts service to original line after restoration.

<RVTM>

(Optional) Revertive time. RVTM is not allowed to be set while RVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).

  • 0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<SRVRTV>

(Optional) The span revertive mode for four-fiber MS-SPRing only. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

<SRVTM>

(Optional) The span revertive time for four-fiber MS-SPRing only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).

  • 0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<EASTWORK>

(Optional) East working facility. AID from the “FACILITY” section.

<WESTWORK>

(Optional) West working facility. AID from the “FACILITY” section.

<EASTPROT>

(Optional) East protecting facility. AID from the “FACILITY” section.

<WESTPROT>

(Optional) West protecting facility. AID from the “FACILITY” section.

21.7 RTRV-<PATH>

(Cisco ONS 15454 SDH) The Retrieve VC3, VC44C, VC38C, VC464C, VC48C, VC4-12C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (RTRV-<PATH>) command retrieves the attributes associated with an VC path. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

  • Supported AIDs are: ALL, SLOT-N (N=1,2,...,ALL), and VC-specific AIDs.
  • The SFBER, SDBER, RVRTV, RVTM, HOLDOFFTIMER, and SNCPPTHSTATE parameters only apply to subnetwork connection protection (SNCP).
  • The path trace message is a 64 character string including the terminating carriage return (CR) and line feed (LF) that is transported in the J1 byte of the SDH VC path overhead.
  • The EXPTRC indicates the contents of the expected incoming path trace that are provisioned by the user in the ED-VC_PATH command. The TRC indicates the contents of the outgoing path trace message. The INCTRC indicates the contents of the incoming path trace message.
  • The path trace mode has three modes: OFF, MANUAL, and AUTO. The mode defaults to OFF. The MANUAL mode compares the received string with the user-entered expected string. The AUTO mode compares the present received string with an expected string set to a previously received string. If there is a mismatch, the TIM-P alarm is raised. When the path trace mode is in OFF mode, there is no path trace processing, and all the alarm and state conditions are reset.

When the expected string is queried under the OFF path trace mode, the expected string is a copy of the provisioned string, or NULL. When an expected string is queried under the MANUAL path trace mode, the expected string is a copy of the user entered string. When an expected string is queried under the AUTO path trace mode, the expected string is either a copy of the acquired received string, or NULL if the string has not been acquired.

When the incoming string is queried under the OFF path trace mode, the incoming string is NULL. When an incoming string is queried under the MANUAL or AUTO path trace mode, the incoming string is either a copy of the received string, or NULL if the string has not been received.

  • J1 (EXPTRC) is implemented on the STM1, STM16AS, STM64, MRC-12, and STM64-XFP cards.
  • The optional parameter MSSPRPTHTYPE provides more options to retrieve J1/C2 of a particular MS-SPRing path. This field is valid only if the queried AID port has MS-SPRing. The MSSPRPTHTYPE defaults to NON-PCA path type if the MS-SPRing is switched, or defaults to PCA if there is no MS-SPRing switching.

Sending this command while MSSPRPTHTYPE=PCA, whether there is MS-SPRing switch or not, the protection channel access (PCA) path J1/C2 data will be returned (if there is PCA circuit on the AID). Sending this command with a VC AID without circuits and no MS-SPRing switched on the VC, will return and error message.

  • An optional output parameter MSSPRPTHSTATE is introduced into this command output on the Cisco ONS 15454 SDH platform only. Each J1/C2 output data of this command will include the MS-SPRing path state information.
  • After the MS-SPRing switching, the J1/IPPM/C2 data can be retrieved over the protection path. Provisioning J1 trace string, trace mode, or threshold is not allowed on the protection path.
  • HOLDOFFTIMER is not specific to a path. Instead, it is applicable to the SNCP selector.
  • To retrieve either the cross-connect points or the test access points (TAPs) on the DS3i-N-12 card, the RTRV-VC3 command with the appropriate AID must be used.
  • In LAN to WAN card mode, ALL aid is not supported for RTRV-VC464c.

Category

Paths

Security

Retrieve

Input Format

RTRV-<PATH>:[<TID>]:<AID>:<CTAG>:::[MSSPRPTHTYPE=<MSSPRPTHTYPE>][:];

Input Example

Cisco ONS 15454 SDH

RTRV-VC4:FERNDALE:VC4-2-1-4:238:::MSSPRPTHTYPE=NON-PCA;

 

Table 21-5 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “CrossConnectId1” section.

<MSSPRPTHTYPE>

(Optional) The MS-SPRing path type (only if the port is on the MS-SPRing). Defaults to NON-PCA. Applicable only to VC-level paths in SDH. A null value defaults to NON-PCA. The parameter type is MSSPR_PTH_TYPE, which is the MS-SPRing path type only if the port is on the MS-SPRing.

  • NON-PCA

The AID is on the working path, or the cross-connection card protection path.

  • PCA

The AID is on the MS-SPRing PCA path.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>::[LEVEL=<LEVEL>],[SFBER=<SFBER>],[SDBER=<SDBER>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[HOLDOFFTIMER=<HOLDOFFTIMER>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>],[INCTRC=<INCTRC>],
[TRCMODE=<TRCMODE>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[SNCPPTHSTATE=<SNCPPTHSTATE>],[C2=<C2>],
[MSSPRPTHSTATE=<MSSPRPTHSTATE>]:<PSTPSTQ>,[<SSTQ>]”
;

Output Example

Cisco ONS 15454 SDH

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“VC4-2-1-4::LEVEL=VC4,SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
HOLDOFFTIMER=2000,EXPTRC=“EXPTRCSTRING”,TRC=“TRCSTRING”,
INCTRC=“INCTRCSTRING”,TRCMODE=AUTO,TACC=8,TAPTYPE=DUAL,
SNCPPTHSTATE=ACT,C2=0X04,
MSSPRPTHSTATE=PROTPTHACT:UNLOCKED-DISABLED,AUTOMATICINSERVICE”

;

Table 21-6 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “CrossConnectId1” section.

<LEVEL>

(Optional) The rate of the cross-connected channel. Applicable only to High-Order paths (VC4). The parameter type is PATH, which is the modifier for path commands.

  • VC3

Synchronous Transport Signal/Module Level-1 (51 Mbps)

  • VC44C

Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps)

  • VC38C

Synchronous Transport Signal/Module Level-18 Concatenated (933 Mbps)

  • VC464C

Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps)

  • VC48C

Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps)

  • VC4

Synchronous Transport Signal/Module Signal Level-3 Concatenated (155 Mbps)

  • VC416C

Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps)

  • VC42C

Synchronous Transport Signal/Module level-6 (310 Mbps)

  • VC43C

Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps)

  • VC12

Virtual Tributary 2. Virtual Channel 12

  • VC11

Virtual Tributary 1. Virtual Channel 11

<SFBER>

(Optional) A VC path signal failure threshold that only applies to SNCP. Applicable only to High-Order paths. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

  • 1E-3

SFBER is 1E-3.

  • 1E-4

SFBER is 1E-4.

  • 1E-5

SFBER is 1E-5.

<SDBER>

(Optional) A VC path signal degrade threshold that only applies to SNCP. Applicable only High-Order paths. Defaults 1E-6. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

  • 1E-5

SDBER is 1E-5.

  • 1E-6

SDBER is 1E-6.

  • 1E-7

SDBER is 1E-7.

  • 1E-8

SDBER is 1E-8.

  • 1E-9

SDBER is 1E-9.

<RVRTV>

(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Does not revert service to original line after restoration.

  • Y

Reverts service to original line after restoration.

RVTM

(Optional) Revertive time. Only applies to SNCP. The parameter type is REVERTIVE_TIME (revertive time).

  • 0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

  • N

Disable an attribute.

  • Y

Enable an attribute.

<HOLDOFFTIMER>

(Optional) Hold off timer. HOLDOFFTIMER is an integer.

<EXPTRC>

(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR and LF. Applicable to VC-level paths (VCn). Defaults to NULL when SNCP path is created. EXPTRC is a string.

<TRC>

(Optional) The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. A null value defaults to the NE transmitting null characters (Hex 00). Applicable to VC-level paths (VCn). TRC is a string.

<INCTRC>

(Optional) The incoming path trace message contents. INCTRC is any combination of 64 characters. Applicable only to VC-level paths in (VCn). Defaults to Null when a SNCP path is created. INCTRC is a string.

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level paths (VCn). Defaults to OFF when a SNCP path is created. The parameter type is TRCMODE, which is the trace mode.

  • AUTO

Use the previously received path trace string as the expected string (not applicable to MXP_2.5G_10G and TXP_MR_10G cards).

  • AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP detected.

  • MAN

Use the provisioned expected string as the expected string.

  • MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP detected.

  • OFF

Turn off path trace capability. Nothing will be reported.

<TACC>

(Optional) Test access. Indicates whether the digroup being provisioned is to be used as a test access digroup. Defaults to N.

<TAPTYPE>

(Optional) TAP type. The parameter type is TAPTYPE, which is the test access point type.

  • DUAL

Dual facility access digroup (FAD).

  • SINGLE

Single FAD

<SNCPPTHSTATE>

(Optional) Indicates whether a given AID is the working or standby path of a SNCP cross-connect. The parameter type is STATUS, which is the status of the unit in the protection pair.

  • ACT

The entity is the active unit in the shelf.

  • NA

Status is unavailable.

  • STBY

The entity is the standby unit in the shelf.

<C2>

(Optional) The C2 byte hex code. Applicable only to VC-level paths (VCn). The parameter type is C2_BYTE, which is the C2 byte hex code.

  • 0X00

Unequipped

  • 0X01

Equipped-Non Specific payload

  • 0X02

VT-Structured VC-1 synchronous payload envelope (SPE)

  • 0X03

Locked Virtual Tributary (VT) mode

  • 0X04

Asynchronous Mapping for DS3

  • 0X12

Asynchronous Mapping for DS4 North American (NA)

  • 0X13

Mapping for asynchronous transfer mode (ATM)

  • 0X14

Mapping for distributed queue dual bus (DQDB)

  • 0X15

Asynchronous Mapping for fiber distributed data interface (FDDI)

  • 0X16

High-level data link control (HDLC)-Over-SDH Mapping

  • 0XE1

VT-structured VC4-1 SPE with 1VTx payload defect

  • 0XE2

VT-structured VC4-1 SPE with 2VTx payload defects

  • 0XE3

VT-structured VC4-1 SPE with 3VTx payload defects

  • 0XE4

VT-structured VC4-1 SPE with 4VTx payload defects

  • 0XE5

VT-structured VC4-1 SPE with 5VTx payload defects

  • 0XE6

VT-structured VC4-1 SPE with 6VTx payload defects

  • 0XE7

VT-structured VC4-1 SPE with 7VTx payload defects

  • 0XE8

VT-structured VC4-1 SPE with 8VTx payload defects

  • 0XE9

VT-structured VC4-1 SPE with 9VTx payload defects

  • 0XEA

VT-structured VC4-1 SPE with 10VTx payload defects

  • 0XEB

VT-structured VC4-1 SPE with 11VTx payload defects

  • 0XEC

VT-structured VC4-1 SPE with 12VTx payload defects

  • 0XED

VT-structured VC4-1 SPE with 13VTx payload defects

  • 0XEE

VT-structured VC4-1 SPE with 14VTx payload defects

  • 0XEF

VT-structured VC4-1 SPE with 15VTx payload defects

  • 0XF0

VT-structured VC4-1 SPE with 16VTx payload defects

  • 0XF1

VT-structured VC4-1 SPE with 17VTx payload defects

  • 0XF2

VT-structured VC4-1 SPE with 18VTx payload defects

  • 0XF3

VT-structured VC4-1 SPE with 19VTx payload defects

  • 0XF4

VT-structured VC4-1 SPE with 20VTx payload defects

  • 0XF5

VT-structured VC4-1 SPE with 21VTx payload defects

  • 0XF6

VT-structured VC4-1 SPE with 22VTx payload defects

  • 0XF7

VT-structured VC4-1 SPE with 23VTx payload defects

  • 0XF8

VT-structured VC4-1 SPE with 24VTx payload defects

  • 0XF9

VT-structured VC4-1 SPE with 25VTx payload defects

  • 0XFA

VT-structured VC4-1 SPE with 26VTx payload defects

  • 0XFB

VT-structured VC4-1 SPE with 27VTx payload defects

  • 0XFC

VT-structured VC4-1 SPE with 28VTx payload defects

  • 0XFE

O.181 Test Signal (TSS1 to TSS3) Mapping

  • 0XFF

Reserved. C2 is 0XFF if AIS-L is being generated by an optical card or cross-connect downstream.

<MSSPRPTHSTATE>

(Optional) The MS-SPRing path state only if the port is on the MS-SPRing. Applicable only to VC-level paths in SDH (VCn). The parameter type is MSSPR_PTH_STATE, which is the MS-SPRing path state only if the port is on the MS-SPRing.

  • PCAPTHACT

Indicates that the MS-SPRing switched and its PCA path is in the active state.

  • PCAPTHSTB

Indicates that the MS-SPRing switched and its PCA path is in the standby state.

  • PROTPTHACT

Indicates that the MS-SPRing switched and its protection path is in the active state.

  • WKGPTHACT

Indicates that the MS-SPRing switched and its working path is in the active state.

  • WKGPTHSTB

Indicates that the MS-SPRing switched and its working path is in the standby state.

<PSTPSTQ>

Administrative state in the PST_PSTQ format. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and the PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked-Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SSTQ>

(Optional) Secondary state of the entity. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.8 RTRV-<STM_TYPE>

(Cisco ONS 15454 SDH) The Retrieve (STM1, STM4, STM16, STM64) command retrieves the attributes (such as service parameters) and the state of an STM facility. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

  • Both RINGID and MSSPRTYPE identify the STM port connected with a MS-SPRing. These attributes are only presented for the STM4, STM16, and STM64 ports within a MS-SPRing connection. The RTRV-<MOD_RING> command with the AID MSSPR-RINGID, can provide more information on this MS-SPRing.
  • This command does not show the WVLEN attribute if the STM port has zero value on WVLEN.

Category

Ports

Security

Retrieve

Input Format

RTRV-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-STM16:PENNGROVE:FAC-6-1:236;

Input Parameters

<AID>

Access identifier from the “FACILITY” section.

Output Format

Cisco ONS 15454 SDH

SID DATE TIME
M CTAG COMPLD
“<AID>:,,[<ROLE>],[<STATUS>]:[RSDCC=<RSDCC>],[AREA=<AREA>],
[TMGREF=<TMGREF>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],
[PJMON=<PJMON>],[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],
[WVLEN=<WVLEN>],[RINGID=<RINGID>],[MSSPRTYPE=<MSSPRTYPE>],
[MUX=<MUX>],[UNIC=<UNIC>],[CCID=<CCID>],[NBRIX=<NBRIX>],[SOAK=<SOAK>],
[SOAKLEFT=<SOAKLEFT>],[SSMRCV=<SSMRCV>],[OSPF=<OSPF>],
[MSDCC=<MSDCC>],[NAME=<NAME>],[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>], [TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>], [SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>], [FOREIGNIPADDRESS=<FOREIGNIPADDRESS>],
[SQUELCHMODE=<SQUELCHMODE>], <PSTPSTQ>,[<SSTQ>]”
;

Output Example

Cisco ONS 15454 SDH

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“FAC-6-1:,,WORK,ACT:RSDCC=Y,AREA=10.92.63.1,TMGREF=N,SYNCMSG=N,SENDDUS=N,
PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,WVLEN=1310.00,RINGID=43,
MSSPRTYPE=WESTWORK,MUX=E2,UNIC=Y,CCID=8,NBRIX=2,SOAK=52,
SOAKLEFT=12-25,SSMRCV=STU_SDH,OSPF=Y,MSDCC=Y,NAME=\“STM PORT\”,
LBCL=10.0,OPT=10.0,OPR=10.0, EXPTRC=“AAA”,TRC=“AAA”,TRCMODE=MAN,
TRCFORMAT=16-BYTE,ADMSSM=G811, SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=Y,
FOREIGNIPADDRESS=10.92.63.44,UNLOCKED-DISABLED,AUTOMATICINSERVICE”;

 

Table 21-7 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “FACILITY” section.

<ROLE>

(Optional) An STM port role. The parameter type is SIDE, which is the role the unit is playing in the protection group.

  • PROT

The entity is a protection unit in the protection group.

  • ACT

The entity is the active unit in the shelf.

  • NA

Status is unavailable.

  • STBY

The entity is the standby unit in the shelf.

<RSDCC>

(Optional) Indicates whether or not the regenerator section DCC (RS-DCC) is to be used. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

  • N

The ring does not support the extended K1/K2/K3 protocol.

  • Y

The ring does support the extended K1/K2/K3 protocol.

<AREA>

(Optional) Area ID. Shows up only if the DCC is enabled. AREA is a string.

<TMGREF>

(Optional) The termination to be used, whether primary or secondary. Identifies if an STM port has a timing reference. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute)

  • N

Disable an attribute.

  • Y

Enable an attribute.

<SYNCMSG>

(Optional) Synchronization status message. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

  • N

The ring does not support the extended K1/K2/K3 protocol.

  • Y

The ring does support the extended K1/K2/K3 protocol.

<SENDDUS>

(Optional) The facility will send the Do Not Use for Synchronization (DUS) value in 0x0f bit pattern as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute)

  • N

Disable an attribute.

  • Y

Enable an attribute.

<PJMON>

(Optional) Identifies an STM port PJMON. Defaults to 0 (zero). PJMON is an integer. Set a valid VC4 number of the optical port.

Note The PJMON number displayed in TL1 interface does not correspond to the PJVC4MON number in CTC, but instead corresponds to the VC4 number of the optical port.

<SFBER>

(Optional) An STM port signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

  • 1E-3

SFBER is 1E-3.

  • 1E-4

SFBER is 1E-4.

  • 1E-5

SFBER is 1E-5.

<SDBER>

(Optional) An STM port signal degrade threshold. Defaults 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

  • 1E-5

SDBER is 1E-5.

  • 1E-6

SDBER is 1E-6.

  • 1E-7

SDBER is 1E-7.

  • 1E-8

SDBER is 1E-8.

  • 1E-9

SDBER is 1E-9.

<MODE>

(Optional) STM port mode. Defaults to SDH. The parameter type is OPTICAL_MODE, which is the facility’s optical mode.

  • SINGLESHELF

The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.

  • MULTISHELF

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.

  • MULTISHELFETH

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.

<WVLEN>

(Optional) An STM port wavelength, expressed in nanometers. For example, WVLEN=1310.00 means it operates at 1310 nm in the DWDM application. WVLEN is a float.

<RINGID>

(Optional) The MS-SPRing RINGID with which the port is connected. RINGID ranges from 0 to 9999. RINGID is an integer.

<MSSPRTYPE>

(Optional) The MS-SPRing type with which the port is connected. The parameter type is MSSPR_TYPE, which is the MS-SPRing type of an STM port.

  • EASTPROT

The STM port is an east protecting port.

  • EASTWORK

The STM port is an east working port.

  • WESTPROT

The STM port is an west protecting port.

  • WESTWORK

The STM port is an west working port.

<MUX>

(Optional) MS-SPRing extension byte. The parameter type is MUX_TYPE, which is the MS-SPRing extension byte.

  • E2

E2 byte (orderwire)

  • F1

F1 byte (user)

  • K3

K3 byte

  • Z2

Z2 byte

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.

<SOAKLEFT>

(Optional) Time remaining for the transition from Locked-AutomaticInService to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. Rules for <SOAKLEFT> are:

  • When the port is in Locked, Locked_Maintenance or Unlocked state, the parameter will not appear.
  • When the port is in Locked_AutomaticInService, but the countdown has not started due to fault signal the value will be SOAKLEFT=NOT-STARTED.
  • When the port is in Locked_AutomaticInService state and the countdown has started the value will be shown in HH-MM format.

<SSMRCV>

(Optional) Displays the quality of the individual port. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

  • DUS_SDH

Do Not Use For Synchronization

  • G811

G811 Standard

  • RES_SDH

Reserved For Network Synchronization Use

  • G812T

G812T Standard

  • STU_SDH

Synchronized, Traceability Unknown

  • G812TL

G812TL Standard

  • SETS

Synchronous Equipment Timing Source

<OSPF>

(Optional) The Open Shortest Path First discovery. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

<MS-DCC>

(Optional) The line DCC connection on the port. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

  • N

The ring does not support the extended K1/K2/K3 protocol.

  • Y

The ring does support the extended K1/K2/K3 protocol.

<NAME>

(Optional) Port Name. NAME is a string.

<LBCL>

(Optional) Displays the current value of the laser current. LBCL is a float.

<OPT>

(Optional) Displays the current value of the transmitted optical power. OPT is only displayed for DWDM cards. OPT is a float.

<OPR>

(Optional) Received optical power. OPR is a float.

<EXPTRC>

(Optional) Expected path trace content. EXPTRC is a string.

<TRC>

(Optional) Path trace message to be transmitted. TRC is a string.

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level Paths in SDH (VCn). Defaults to the OFF mode. The parameter type is TRCMODE (trace mode).

  • AUTO

Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.

  • AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected.

  • MAN

Use the provisioned expected string as the expected string.

  • MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected.

  • OFF

Turn off path trace capability. Nothing will be reported.

<TRCFORMAT>

(Optional) Trace message size. The parameter type is TRCFORMAT, which is the trace format.

  • 1-BYTE

1 byte trace message

  • 16-BYTE

16 byte trace message

  • 64-BYTE

64 byte trace message

  • Y

Enable an attribute

<ADMSSM>

(Optional) SSM selectable value. Only displayed when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

  • DUS_SDH

Do Not Use For Synchronization

  • G811

G811 Standard

  • RES_SDH

Reserved For Network Synchronization Use

  • G812T

G812T Standard

  • STU_SDH

Synchronized, Traceability Unknown

  • G812TL

G812TL Standard

  • SETS

Synchronous Equipment Timing Source

<SENDDUSFF>

(Optional) Indicates that the facility will send the DUS value in 0xff bits pattern as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute

  • Y

Enable an attribute

<AISONLPBK>

(Optional) The parameter type is AIS_ON_LPBK, which indicates if AIS should be sent on loopback.

  • AIS_ONLPBK_FACILITY

AIS is sent on facility loopback.

  • AIS_ON_LPBK_ALL

AIS is sent on all loopbacks.

  • AIS_ON_LPBK_OFF

AIS is not sent on loopback.

  • AIS_ON_LPBK_TERMINAL

AIS is sent on terminal loopback.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

  • 1310

Wavelength 1310

  • 1470

Wavelength 1470

  • 1490

Wavelength 1490

  • 1510

Wavelength 1510

  • 1529.55

Wavelength 1529.55

  • 1529.94

Wavelength 1529.94

  • 1530

Wavelength 1530

  • 1530.33

Wavelength 1530.33

  • 1530.73

Wavelength 1530.73

  • 1531.12

Wavelength 1531.12

  • 1531.51

Wavelength 1531.51

  • 1531.90

Wavelength 1531.90

  • 1532.29

Wavelength 1532.29

  • 1532.68

Wavelength 1532.68

  • 1533.07

Wavelength 1533.07

  • 1533.47

Wavelength 1533.47

  • 1533.86

Wavelength 1533.86

  • 1534.25

Wavelength 1534.25

  • 1534.64

Wavelength 1534.64

  • 1535.04

Wavelength 1535.04

  • 1535.43

Wavelength 1535.43

  • 1535.82

Wavelength 1535.82

  • 1536.22

Wavelength 1536.22

  • 1536.61

Wavelength 1536.61

  • 1537

Wavelength 1537

  • 1537.40

Wavelength 1537.40

  • 1537.79

Wavelength 1537.79

  • 1538.19

Wavelength 1538.19

  • 1538.58

Wavelength 1538.58

  • 1538.98

Wavelength 1538.98

  • 1539.37

Wavelength 1539.37

  • 1539.77

Wavelength 1539.77

  • 1540.16

Wavelength 1540.16

  • 1540.56

Wavelength 1540.56

  • 1540.95

Wavelength 1540.95

  • 1541.35

Wavelength 1541.35

  • 1541.75

Wavelength 1541.75

  • 1542.14

Wavelength 1542.14

  • 1542.35

Wavelength 1542.35

  • 1542.54

Wavelength 1542.54

  • 1542.94

Wavelength 1542.94

  • 1543.33

Wavelength 1543.33

  • 1543.73

Wavelength 1543.73

  • 1544.13

Wavelength 1544.13

  • 1544.53

Wavelength 1544.53

  • 1544.92

Wavelength 1544.92

  • 1545.32

Wavelength 1545.32

  • 1545.72

Wavelength 1545.72

  • 1546.12

Wavelength 1546.12

  • 1546.52

Wavelength 1546.52

  • 1546.92

Wavelength 1546.92

  • 1547.32

Wavelength 1547.32

  • 1547.72

Wavelength 1547.72

  • 1548.12

Wavelength 1548.12

  • 1548.51

Wavelength 1548.51

  • 1548.92

Wavelength 1548.92

  • 1549.32

Wavelength 1549.32

  • 1549.71

Wavelength 1549.71

  • 1550

Wavelength 1500

  • 1550.12

Wavelength 1550.12

  • 1550.52

Wavelength 1550.52

  • 1550.92

Wavelength 1550.92

  • 1551.32

Wavelength 1551.32

  • 1551.72

Wavelength 1551.72

  • 1552.12

Wavelength 1552.12

  • 1552.52

Wavelength 1552.52

  • 1552.93

Wavelength 1552.93

  • 1553.33

Wavelength 1553.33

  • 1553.73

Wavelength 1553.73

  • 1554.13

Wavelength 1554.13

  • 1554.13

Wavelength 1554.13

  • 1554.94

Wavelength 1554.94

  • 1555.34

Wavelength 1555.34

  • 1555.75

Wavelength 1555.75

  • 1556.15

Wavelength 1556.15

  • 1556.55

Wavelength 1556.55

  • 1556.96

Wavelength 1556.96

  • 1557.36

Wavelength 1557.36

  • 1557.77

Wavelength 1557.77

  • 1558.17

Wavelength 1558.17

  • 1558.58

Wavelength 1558.58

  • 1558.98

Wavelength 1558.98

  • 1559.39

Wavelength 1559.39

  • 1559.79

Wavelength 1559.79

  • 1560.20

Wavelength 1560.20

  • 1560.61

Wavelength 1560.61

  • 1561.01

Wavelength 1561.01

  • 1561.42

Wavelength 1561.42

  • 1561.83

Wavelength 1561.83

  • 1570

Wavelength 1570

  • 1570.83

Wavelength 1570.83

  • 1571.24

Wavelength 1571.24

  • 1571.65

Wavelength 1571.65

  • 1572.06

Wavelength 1572.06

  • 1572.48

Wavelength 1572.48

  • 1572.89

Wavelength 1572.89

  • 1573.30

Wavelength 1573.30

  • 1573.71

Wavelength 1573.71

  • 1574.13

Wavelength 1574.13

  • 1574.54

Wavelength 1574.54

  • 1574.95

Wavelength 1574.95

  • 1575.37

Wavelength 1575.37

  • 1575.78

Wavelength 1575.78

  • 1576.20

Wavelength 1576.20

  • 1576.61

Wavelength 1576.61

  • 1577.03

Wavelength 1577.03

  • 1577.44

Wavelength 1577.44

  • 1577.86

Wavelength 1577.86

  • 1578.27

Wavelength 1578.27

  • 1578.69

Wavelength 1578.69

  • 1579.10

Wavelength 1579.10

  • 1579.52

Wavelength 1579.52

  • 1579.93

Wavelength 1579.93

  • 1580.35

Wavelength 1580.35

  • 1580.77

Wavelength 1580.77

  • 1581.18

Wavelength 1581.18

  • 1581.60

Wavelength 1581.60

  • 1582.02

Wavelength 1582.02

  • 1582.44

Wavelength 1582.44

  • 1582.85

Wavelength 1582.85

  • 1583.27

Wavelength 1583.27

  • 1583.69

Wavelength 1583.69

  • 1584.11

Wavelength 1584.11

  • 1584.53

Wavelength 1584.53

  • 1584.95

Wavelength 1584.95

  • 1585.36

Wavelength 1585.36

  • 1585.78

Wavelength 1585.78

  • 1586.20

Wavelength 1586.20

  • 1586.62

Wavelength 1586.62

  • 1587.04

Wavelength 1587.04

  • 1587.46

Wavelength 1587.46

  • 1587.88

Wavelength 1587.88

  • 1588.30

Wavelength 1588.30

  • 1588.73

Wavelength 1588.73

  • 1589.15

Wavelength 1589.15

  • 1589.57

Wavelength 1589.57

  • 1589.99

Wavelength 1589.99

  • 1590

Wavelength 1590

  • 1590.41

Wavelength 1590.41

  • 1590.83

Wavelength 1590.83

  • 1591.26

Wavelength 1591.26

  • 1591.68

Wavelength 1591.68

  • 1592.10

Wavelength 1592.10

  • 1592.52

Wavelength 1592.52

  • 1592.95

Wavelength 1592.95

  • 1593.37

Wavelength 1593.37

  • 1593.79

Wavelength 1593.79

  • 1594.22

Wavelength 1594.22

  • 1594.64

Wavelength 1594.64

  • 1595.06

Wavelength 1595.06

  • 1595.49

Wavelength 1595.49

  • 1596.34

Wavelength 1596.34

  • 1596.76

Wavelength 1596.76

  • 1597.19

Wavelength 1597.19

  • 1597.62

Wavelength 1597.62

  • 1598.04

Wavelength 1598.04

  • 1598.47

Wavelength 1598.47

  • 1598.89

Wavelength 1598.89

  • 1599.32

Wavelength 1599.32

  • 1599.75

Wavelength 1599.75

  • 1600.06

Wavelength 1600.06

  • 1601.03

Wavelength 1601.03

  • 1601.46

Wavelength 1601.46

  • 1601.88

Wavelength 1601.88

  • 1602.31

Wavelength 1602.31

  • 1602.74

Wavelength 1602.74

  • 1603.17

Wavelength 1603.17

  • 1603.60

Wavelength 1603.60

  • 1604.03

Wavelength 1604.03

  • 1610

Wavelength 1610

  • USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

  • AUTOPROV

Autoprovisioning

  • CX

Reach CX

  • CX1

Reach CX1

  • DX

Reach DX

  • HX

Reach HX

  • I1

Reach I1

  • IR-1

Reach IR-1

  • IR-2

Reach IR-2

  • L1

Reach L1

  • L2

Reach L2

  • L3

Reach L3

  • LR-1

Reach LR-1

  • LR-2

Reach LR-2

  • LR-3

Reach LR-3

  • LX

Reach LX

  • S1

Reach S1

  • S2

Reach S2

  • SR

Reach SR

  • SR-1

Reach SR-1

  • SX

Reach SX

  • T

Reach T

  • TEN-GE-ER

10 GE extended range

  • TEN-GE-LR

10 GE long range

  • TEN-GE-SR

10 GE short range

  • VX

Reach VX

  • ZX

Reach ZX

<FOREIGNFEND>

(Optional) Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF (disable or enabled an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

<FOREIGNIP>

(Optional) The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGNIP is a string.

<SQUELCHMODE>

Shuts down the far-end laser in response to certain defects.

  • SQUELCH

Squelch is enabled.

  • NONE

No Squelch

  • G-AIS

Generic AIS

<PSTPSTQ>

(Optional) Administrative state in the PST_PSTQ format. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked -Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SSTQ>

(Optional) The secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.9 RTRV-10GIGE

(Cisco ONS 15454 SDH) The Retrieve 10GIGE (RTRV-10GIGE) command retrieves the 10-Gbps-specific parameters for a port that has been configured to support the Gigabit Ethernet payload with the ENT-10GIGE command.

 
Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-10GIGE:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-10GIGE:TID:FAC-1-1:100;

Input Parameters

<AID>

Access identifier from the “FACILITY” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],[MACADDR=<MACADDR>],
[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,[<SST>]”
;

Output Examples

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“FAC-6-1:,,WORK,ACT:NAME=\"NY PORT\",MACADDR=00-0E-AA-BB-CC-FF,LBCL=10.0,
OPT=10.0,OPR=10.0,FREQ=1550,LOSSB=SX:Unlocked-Disabled,AutomaticInService”
;

 

Table 21-8 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “FACILITY” section.

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.

  • STBY

The entity is the standby unit in the shelf.

<NAME>

(Optional) Port name. NAME is a string.

<MACADDR>

(Optional) The MAC address for the 10 Gigabit Ethernet payload. MACADDR is a string.

<LBCL>

(Optional) Displays the current value of the laser current. LBCL is a float.

<OPT>

(Optional) Displays the current value of the transmitted optical power. OPT is a float.

<OPR>

(Optional) Displays the current value of the received optical power. OPR is a float.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

  • 1310

Wavelength 1310

  • 1470

Wavelength 1470

  • 1490

Wavelength 1490

  • 1510

Wavelength 1510

  • 1528.77

Wavelength 1528.77

  • 1529.55

Wavelength 1529.55

  • 1529.94

Wavelength 1529.94

  • 1530

Wavelength 1530

  • 1530.33

Wavelength 1530.33

  • 1530.73

Wavelength 1530.73

  • 1531.12

Wavelength 1531.12

  • 1531.51

Wavelength 1531.51

  • 1531.90

Wavelength 1531.90

  • 1532.29

Wavelength 1532.29

  • 1532.68

Wavelength 1532.68

  • 1533.07

Wavelength 1533.07

  • 1533.47

Wavelength 1533.47

  • 1533.86

Wavelength 1533.86

  • 1534.25

Wavelength 1534.25

  • 1534.64

Wavelength 1534.64

  • 1535.04

Wavelength 1535.04

  • 1535.43

Wavelength 1535.43

  • 1535.82

Wavelength 1535.82

  • 1536.22

Wavelength 1536.22

  • 1536.61

Wavelength 1536.61

  • 1537

Wavelength 1537

  • 1537.40

Wavelength 1537.40

  • 1537.79

Wavelength 1537.79

  • 1538.19

Wavelength 1538.19

  • 1538.58

Wavelength 1538.58

  • 1538.98

Wavelength 1538.98

  • 1539.37

Wavelength 1539.37

  • 1539.77

Wavelength 1539.77

  • 1540.16

Wavelength 1540.16

  • 1540.56

Wavelength 1540.56

  • 1540.95

Wavelength 1540.95

  • 1541.35

Wavelength 1541.35

  • 1541.75

Wavelength 1541.75

  • 1542.14

Wavelength 1542.14

  • 1542.35

Wavelength 1542.35

  • 1542.54

Wavelength 1542.54

  • 1542.94

Wavelength 1542.94

  • 1543.33

Wavelength 1543.33

  • 1543.73

Wavelength 1543.73

  • 1544.13

Wavelength 1544.13

  • 1544.53

Wavelength 1544.53

  • 1544.92

Wavelength 1544.92

  • 1545.32

Wavelength 1545.32

  • 1545.72

Wavelength 1545.72

  • 1546.12

Wavelength 1546.12

  • 1546.52

Wavelength 1546.52

  • 1546.92

Wavelength 1546.92

  • 1547.32

Wavelength 1547.32

  • 1547.72

Wavelength 1547.72

  • 1548.12

Wavelength 1548.12

  • 1548.51

Wavelength 1548.51

  • 1548.92

Wavelength 1548.92

  • 1549.32

Wavelength 1549.32

  • 1549.71

Wavelength 1549.71

  • 1550

Wavelength 1500

  • 1550.12

Wavelength 1550.12

  • 1550.52

Wavelength 1550.52

  • 1550.92

Wavelength 1550.92

  • 1551.32

Wavelength 1551.32

  • 1551.72

Wavelength 1551.72

  • 1552.12

Wavelength 1552.12

  • 1552.52

Wavelength 1552.52

  • 1552.93

Wavelength 1552.93

  • 1553.33

Wavelength 1553.33

  • 1553.73

Wavelength 1553.73

  • 1554.13

Wavelength 1554.13

  • 1554.13

Wavelength 1554.13

  • 1554.94

Wavelength 1554.94

  • 1555.34

Wavelength 1555.34

  • 1555.75

Wavelength 1555.75

  • 1556.15

Wavelength 1556.15

  • 1556.55

Wavelength 1556.55

  • 1556.96

Wavelength 1556.96

  • 1557.36

Wavelength 1557.36

  • 1557.77

Wavelength 1557.77

  • 1558.17

Wavelength 1558.17

  • 1558.58

Wavelength 1558.58

  • 1558.98

Wavelength 1558.98

  • 1559.39

Wavelength 1559.39

  • 1559.79

Wavelength 1559.79

  • 1560.20

Wavelength 1560.20

  • 1560.61

Wavelength 1560.61

  • 1561.01

Wavelength 1561.01

  • 1561.42

Wavelength 1561.42

  • 1561.83

Wavelength 1561.83

  • 1570

Wavelength 1570

  • 1570.83

Wavelength 1570.83

  • 1571.24

Wavelength 1571.24

  • 1571.65

Wavelength 1571.65

  • 1572.06

Wavelength 1572.06

  • 1572.48

Wavelength 1572.48

  • 1572.89

Wavelength 1572.89

  • 1573.30

Wavelength 1573.30

  • 1573.71

Wavelength 1573.71

  • 1574.13

Wavelength 1574.13

  • 1574.54

Wavelength 1574.54

  • 1574.95

Wavelength 1574.95

  • 1575.37

Wavelength 1575.37

  • 1575.78

Wavelength 1575.78

  • 1576.20

Wavelength 1576.20

  • 1576.61

Wavelength 1576.61

  • 1577.03

Wavelength 1577.03

  • 1577.44

Wavelength 1577.44

  • 1577.86

Wavelength 1577.86

  • 1578.27

Wavelength 1578.27

  • 1578.69

Wavelength 1578.69

  • 1579.10

Wavelength 1579.10

  • 1579.52

Wavelength 1579.52

  • 1579.93

Wavelength 1579.93

  • 1580.35

Wavelength 1580.35

  • 1580.77

Wavelength 1580.77

  • 1581.18

Wavelength 1581.18

  • 1581.60

Wavelength 1581.60

  • 1582.02

Wavelength 1582.02

  • 1582.44

Wavelength 1582.44

  • 1582.85

Wavelength 1582.85

  • 1583.27

Wavelength 1583.27

  • 1583.69

Wavelength 1583.69

  • 1584.11

Wavelength 1584.11

  • 1584.53

Wavelength 1584.53

  • 1584.95

Wavelength 1584.95

  • 1585.36

Wavelength 1585.36

  • 1585.78

Wavelength 1585.78

  • 1586.20

Wavelength 1586.20

  • 1586.62

Wavelength 1586.62

  • 1587.04

Wavelength 1587.04

  • 1587.46

Wavelength 1587.46

  • 1587.88

Wavelength 1587.88

  • 1588.30

Wavelength 1588.30

  • 1588.73

Wavelength 1588.73

  • 1589.15

Wavelength 1589.15

  • 1589.57

Wavelength 1589.57

  • 1589.99

Wavelength 1589.99

  • 1590

Wavelength 1590

  • 1590.41

Wavelength 1590.41

  • 1590.83

Wavelength 1590.83

  • 1591.26

Wavelength 1591.26

  • 1591.68

Wavelength 1591.68

  • 1592.10

Wavelength 1592.10

  • 1592.52

Wavelength 1592.52

  • 1592.95

Wavelength 1592.95

  • 1593.37

Wavelength 1593.37

  • 1593.79

Wavelength 1593.79

  • 1594.22

Wavelength 1594.22

  • 1594.64

Wavelength 1594.64

  • 1595.06

Wavelength 1595.06

  • 1595.49

Wavelength 1595.49

  • 1596.34

Wavelength 1596.34

  • 1596.76

Wavelength 1596.76

  • 1597.19

Wavelength 1597.19

  • 1597.62

Wavelength 1597.62

  • 1598.04

Wavelength 1598.04

  • 1598.47

Wavelength 1598.47

  • 1598.89

Wavelength 1598.89

  • 1599.32

Wavelength 1599.32

  • 1599.75

Wavelength 1599.75

  • 1600.06

Wavelength 1600.06

  • 1601.03

Wavelength 1601.03

  • 1601.46

Wavelength 1601.46

  • 1601.88

Wavelength 1601.88

  • 1602.31

Wavelength 1602.31

  • 1602.74

Wavelength 1602.74

  • 1603.17

Wavelength 1603.17

  • 1603.60

Wavelength 1603.60

  • 1604.03

Wavelength 1604.03

  • 1610

Wavelength 1610

  • USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

  • AUTOPROV

Autoprovisioning

  • CX

Reach CX

  • CX1

Reach CX1

  • DX

Reach DX

  • HX

Reach HX

  • I1

Reach I1

  • IR-1

Reach IR-1

  • IR-2

Reach IR-2

  • L1

Reach L1

  • L2

Reach L2

  • L3

Reach L3

  • LR-1

Reach LR-1

  • LR-2

Reach LR-2

  • LR-3

Reach LR-3

  • LX

Reach LX

  • S1

Reach S1

  • S2

Reach S2

  • SR

Reach SR

  • SR-1

Reach SR-1

  • SX

Reach SX

  • T

Reach T

  • TEN-GE-ER

10 GE extended range

  • TEN-GE-LR

10 GE long range

  • TEN-GE-SR

10 GE short range

  • VX

Reach VX

  • ZX

Reach ZX

<PSTPSTQ>

Administrative state in the PSTPSTQ format. The parameter type is PSTPSTQ, which is the service state of the entity described by the PST and the PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked -Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SST>

(Optional) Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.10 RTRV-ALM-<MOD2ALM>

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Retrieve Alarm for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 5GIB, 8GFC, CHGRP, DS1, DS3I, DVBASI, E1, E100, E1000, E3, E4, EC1, ETH, FSTE, G1000, GFPOS, GIGE, HDLC, ILK, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, MSISC, OCH, OMS, OTS, OTU2, OTU3, POS, RPRIF, STM1E, VC3, VC4-4C, VC4-6C, VC4-8C, VC4-12C, VC4, VC4-16C, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-16c, VC4-64c, VCG, VC11, VC12, WLEN, 3GVIDEO, HDSDI, ISC3STP1G, ISC3STP2G, OTU1, or SDSDI (RTRV-ALRM-<MOD2ALM>) command retrieves and sends the current status of alarm conditions. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

The command supports the modifier 3GVIDEO, OTU1, SDSDI, HDSDI, ISC3STP1G, and ISC3STP2G.

  • VT1-n-n-n replaces PS_VC12-n-n-n for the VC12 alarm AID.
  • The [<AIDTYPE>] shows VC3 for VC alarms.

Category

Fault

Security

Retrieve

Input Format

RTRV-ALM-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],[<LOCN>],[<DIRN>][,];

Input Example

RTRV-ALM-OTU1::VFAC-5-3-1:1::MN,,NSA,NEND,RCV;

Table 21-9 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “AidUnionId” section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

(Optional) Condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME

M CTAG COMPLD

"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],

[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"

;

Output Example

tcc2 2011-08-18 16:16:18

M 1 COMPLD

"VFAC-5-3-1,OTU1:MN,HI-RXPOWER,NSA,08-18,12-56-40,NEND,RCV:\"Facility High Rx power\","

;

 

Table 21-10 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section.

<AIDTYPE>

(Optional) Type of access identifier. The parameter type is MOD2ALM, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 1GISC3

1-Gigabit ISC3 compatible

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Fibre Channel payload

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • CLNT

Client facility for MXP/TXP cards

  • CHGRP

Channel group

  • DS3I

DS3i-N-12 facility

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 facility

  • E100

E100 facility

  • E1000

E1000 facility

  • E3

E3 facility

  • E4

E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.

  • FSTE

Fast Ethernet port facility

  • G1000

G1000 facility

  • GFPOS

Generic framing protocol over packet over SDH virtual port facility

  • GIGE

Gigabit Ethernet port facility

  • HDSDI

1.5G HD-SDI video payload.

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • ML1000-2

(ONS 15454) ML-Series two port Gigabit Ethernet card

  • MSISC

MSISC

  • OCH

Optical channel

  • OCHTERM

OCH termination

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port facility

  • SDSDI

270M SDI video payload.

  • STM1

STM1 facility

  • STM1E

STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.

  • STM4

STM4 facility

  • STM16

STM16 facility

  • STM64

STM64 facility

  • VC11

VC11 path

  • VC12

VC12 path

  • VC3

VC3 path

  • VC38C

VC38C path

  • VC44C

VC44C path

  • VC464C

VC464C path

  • VC48C

VC48C path

  • VC4

VC4 path

  • VC416C

VC416C path

  • VC42C

VC42C path

  • VC43C

VC43C path

  • T3

T3 path

  • UDCDCC

UDCDCC path

  • UDCF

UCDF path

  • VCG

Virtual concatenation group alarm

  • WLEN

Wavelength path provisioning

<NTFCNCDE>

Two-letter notification code. the parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See the Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) The condition description.

21.11 RTRV-ALMTYPE

(Cisco ONS 15454 SDH) The Retrieve Alarm Type command retrieves all system and user-defined alarm types.

 
Usage Guidelines

None

Category

System

Security

Retrieve

Input Format

RTRV-ALMTYPE:[<TID>]::<CTAG>;

Input Example

RTRV-ALMTYPE:CISCONODE::1;

Input Parameters

None.

Output Format

SID DATE TIME
M CTAG COMPLD
"<TYPEOFALM>,<ALMTYPE>"
;

Output Examples

CISCONODE 2007-06-26 14:30:00
M 1 COMPLD
"SYSTEMDEFINED,AIRCOMPR"
;

 

Table 21-11 Output Parameter Support

Parameter
Description

<ALMTYPE>

Specifies user-defined alarm types associated with virtual wires in environmental alarm inputs.

<TYPEOFALM>

Specifies the type of alarm, i.e. system or user-defined.

  • SYSTEMDEFINED

Specifies a system-defined alarm type.

  • USERDEFINED

Specifies a user-defined alarm type.

21.12 RTRV-ALM-ALL

(Cisco ONS 15454 SDH) The Retrieve Alarm All (RTRV-ALM-ALL) command retrieves and sends the current status of all active alarm conditions. The alarm condition or severity to be retrieved is specified using the input parameters as a filter. To retrieve all the NE alarms, issue all of the following commands:

RTRV-ALM-ALL
RTRV-ALM-BITS
RTRV-ALM-ENV
RTRV-ALM-SYNCN

 
Usage Guidelines

None

Category

Fault

Security

Retrieve

Input Format

RTRV-ALM-ALL:[<TID>]:[<AID>]:<CTAG>::[<NTFCNCDE>],
[<CONDITION>],[<SRVEFF>],[<LOCN>],[<DIRN>],[,];

Input Example

RTRV-ALM-ALL:COTATI:ALL:229::MN,PWRRESTART,NSA,NEND,RCV;

 

Table 21-12 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section. A null value is equivalent to ALL. AID is a string.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

<CONDITION>

(Optional) The type of alarm condition. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<LOCN>],[<DIRN>]:
[<DESC>],[<AIDDET>]”

;

Output Examples

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SLOT-2,EQPT:MN,PWRRESTART,NSA,08-01,14-25-59,NEND,RCV:\"POWER FAIL RESTART\", DS1-14"
;

 

Table 21-13 Output Parameter Support

Parameter
Description

<AID>

(Optional) Access identifier from the “ALL” section.

<AIDTYPE>

(Optional) Type of facility, link, or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

Building integrated timing supply (BITS) alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 facility

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 facility

  • E3

E3 facility

  • E100

E100 facility

  • ETH

ETH facility

  • E1000

E1000 facility

  • E4

E4 facility

  • ENV

ENV facility

  • EQPT

EQPT facility

  • FSTE

Fast Ethernet port facility

  • G1000

G1000 facility

  • GIGE

Gigabit Ethernet port facility

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload

  • ISC3STP2G

ISC-3 STP 2G video payload

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • ML1000-2

(ONS 15454) ML-Series two port Gigabit Ethernet card

  • ML-100T-8

ML-Series 100T eight port Gigabit Ethernet card

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port facility

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 facility

  • STM1E

STM1E facility

  • STM4

STM4 facility

  • STM16

STM16 facility

  • STM64

STM64 facility

  • SYNCN

SYNCN facility

  • TCC

TCC facility

  • VC11

VC11 path

  • VC12

VC12 path

  • VC3

VC3 path

  • VC44C

VC44C path

  • VC38C

VC38C path

  • VC464C

VC464C path

  • VC48C

VC48C path

  • VC4

VC4 path

  • VC416C

VC416C path

  • VC42C

VC42C path

  • VC43C

VC43C path

  • T3

T3 path

  • UDCDCC

UDCDCC path

  • UDCF

UCDF path

  • VCG

Virtual concatenation group alarm

  • WLEN

Wavelength path provisioning

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<OCRDAT>

Date when the specific event or violation occurred, MM-DD.

<OCRTM>

Time when the specific event or violation occurred, HH-MM-SS.

<DESC>

(Optional) A condition description. DESC is a string.

<AIDDET>

(Optional) The supplementary equipment identification. AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed.

21.13 RTRV-ALM-BITS

(Cisco ONS 15454 SDH) The Retrieve Alarm Building Integrated Timing Supply (RTRV-ALM-BITS) command retrieves and sends the current status of alarm conditions associated with the BITS facility. The alarm condition or severity retrieved is specified using the input parameters as a filter.

 
Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],
[<LOCN>],[<DIRN>];

Input Example

Cisco ONS 15454 SDH

RTRV-ALM-BITS:ELVERANO:BITS-1:228::CR,LOS,SA;

 

Table 21-14 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “BITS” section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed

  • NR

The alarm is not reported

<CONDTYPE>

(Optional) The condition type for an alarm or reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an Cisco ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],[<LOCATION>],[<DIRECTION>]:[<DESC>],”

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“BITS-1,BITS:CR,LOS,SA,08-01,14-25-59,,:\“LOSS OF SIGNAL\”,”
;

 

Table 21-15 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “BITS” section.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

BITS alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 facility

  • E1

E1 facility

  • E3

E3 facility

  • E100

E100 facility

  • E1000

E1000 facility

  • E4

E4 facility

  • ENV

ENV facility

  • EQPT

EQPT facility

  • FSTE

Fast Ethernet port facility

  • G1000

G1000 facility

  • GIGE

Gigabit Ethernet port facility

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port facility

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 facility

  • STM1E

STM1E facility

  • STM4

STM4 facility

  • STM16

STM16 facility

  • STM64

STM64 facility

  • SYNCN

SYNCN facility

  • TCC

TCC facility

  • VC11

VC11 path

  • VC12

VC12 path

  • VC3

VC3 path

  • VC44C

VC44C path

  • VC38C

VC38C path

  • VC464C

VC464C path

  • VC48C

VC48C path

  • VC4

VC4 path

  • VC416C

VC416C path

  • VC42C

VC42C path

  • VC43C

VC43C path

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCATION>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRECTION>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

<DESC>

(Optional) A condition description. DESC is a string.

21.14 RTRV-ALM-ENV

(Cisco ONS 15454 SDH) The Retrieve Alarm Environment (RTRV-ALM-ENV) command retrieves the environmental alarms.

 
Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];

Input Example

RTRV-ALM-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]”

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“ENV-IN-1:MJ,OPENDR,08-01,14-25-59,\“OPEN DOOR\””
;

 

Table 21-16 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section.

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<ALMTYPE>

The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

  • AIRCOMPR

Air compressor failure

  • AIRCOND

Air conditioning failure

  • AIRDRYR

Air dryer failure

  • BATDSCHRG

Battery discharging

  • BATTERY

Battery failure

  • CLFAN

Cooling fan failure

  • CPMAJOR

Centralized power major failure

  • CPMINOR

Centralized power minor failure

  • ENGINE

Engine failure

  • ENGOPRG

Engine operating

  • ENGTRANS

Standby engine transfer

  • EXPLGS

Explosive gas

  • FIRDETR

Fire detector failure

  • FIRE

Fire

  • FLOOD

Flood

  • FUELLEAK

Fuel leak

  • FUSE

Fuse failure

  • GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

  • HATCH

CEV hatch fail

  • GEN

Generator failure

  • HIAIR

High air flow

  • HIHUM

High humidity

  • HITEMP

High temperature

  • HIWTR

High water

  • INTRUDER

Intrusion

  • LEVELCON

Level converter

  • LVDADSL

Secondary ADSL low voltage disconnect

  • LVDBYPAS

Low voltage disconnect bypass

  • LWBATVG

Low battery voltage

  • LWFUEL

Low fuel

  • LWHUM

Low humidity

  • LWPRES

Low cable pressure

  • LWTEMP

Low temperature

  • LWWTR

Low water

  • MISC

Miscellaneous

  • OPENDR

Open door

  • POWER

Commercial power failure

  • PUMP

Pump failure

  • PWR-48

48 V power supply failure

  • PWR-139

–139 V power converter

  • PWR-190

–190 V power converter

  • PWRMJ

Power supply major

  • PWRMN

Power supply minor

  • RECT

Rectifier failure

  • RECTHI

Rectifier high voltage

  • RECTLO

Rectifier low voltage

  • RINGGENMJ

Ringing generator major

  • RINGGENMN

Ringing generator minor

  • RTACADSL

AC or AC/rectifier power fail ADSL equipment

  • RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

  • RTACPWR

AC or AC/rectifier power fail DCL equipment

  • RTACPWRENG

Commercial AC fail, site equipped with standby engine

  • RTBAYPWR

AC power loss distributed power RT bay

  • RTRVENG

Retrieve standby engine, commercial AC restored

  • SMOKE

Smoke

  • TEMP

High-low temperature

  • TOXICGAS

Toxic gas

  • TREPEATER

T-repeater shelf

  • VENTN

Ventilation system failure

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<DESC>

(Optional) A condition description. DESC is a string.

21.15 RTRV-ALM-EQPT

(Cisco ONS 15454 SDH) The Retrieve Alarm Equipment (RTRV-ALM-EQPT) command retrieves and sends the current status of alarm conditions associated with the equipment units. The alarm condition or severity to be retrieved is specified using the input parameters as a filter.

 
Usage Guidelines

None

Category

Equipment

Security

Retrieve

Input Format

RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],
[<LOCN>],[<DIRN>];

Input Example

RTRV-ALM-EQPT:TWOROCK:SLOT-1:227::MJ,HITEMP,NSA;

 

Table 21-17 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “EQPT” section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

(Optional) The condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]”

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SLOT-3,EQPT:MJ,HITEMP,NSA,08-01,14-25-59,,:\“HI TEMPERATURE\”,”
;

 

Table 21-18 Output Parameter Support

Parameter
Description

<AID>

(Optional) Access identifier from the “EQPT” section.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

BITS alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 alarm

  • E1

E1 alarm

  • E3

(ONS 15310 MA SDH) E3 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 alarm

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet port alarm

  • G1000

G1000 alarm

  • GIGE

Gigabit Ethernet port alarm

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port alarm

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 alarm

  • STM1E

STM1E alarm

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • SYNCN

SYNCN alarm

  • TCC

TCC alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC44C

VC44C alarm

  • VC38C

VC38C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) A condition description. DESC is a string.

21.16 RTRV-ALM-SYNCN

(Cisco ONS 15454 SDH) The Retrieve Alarm Synchronization (RTRV-ALM-SYNCN) command retrieves and sends the current status of alarm conditions associated with a synchronization facility. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter.

 
Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>],[<LOCN>],[<DIRN>];

Input Example

RTRV-ALM-SYNCN:FULTON:SYNC-NE:226::CR,FAILTOSW,SA;

 

Table 21-19 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “SYNC_REF” section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

(Optional) The condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]”

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SYNC-NE,SYNCN:CR,FAILTOSW,SA,
08-01,14-25-59,,:\“FAILURE TO SWITCH TO PROTECTION\”,”
;

 

Table 21-20 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “SYN” section.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gbps fiber connection

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

BITS alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 alarm

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 alarm

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet port alarm

  • G1000

G1000 alarm

  • GIGE

Gigabit Ethernet port alarm

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port alarm

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 alarm

  • STM1E

STM1E alarm

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • SYNCN

SYNCN alarm

  • TCC

TCC alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC44C

VC44C alarm

  • VC38C

VC38C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) A condition description. DESC is a string.

21.17 RTRV-ALMTH-<MOD2>

(Cisco ONS 15454 SDH) The Retrieve Alarm Threshold for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 5GIB, 8GFC, D1VIDEO, DS1, DS3I, DV6000, DVBASI, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ILK, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OTU3, STM1, STM4, STM16, STM64, GIGE, POS, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c, VC4-64c, 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, or ISC3STP2G (RTRV-ALMTH-<MOD2>) command retrieves the alarm threshold values. The only applicable MOD2 values are OC3, OC12, OC48, OC192, OCH, OMS, and OTS.

 
Usage Guidelines

The command supports 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G modifiers.

Category

Fault

Security

Retrieve

Input Format

RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<ALMTHR>[,,::];

Input Example

RTRV-ALMTH-OTU1::VFAC-5-3-1:A::OPT-LOW;

 

Table 21-21 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.

<ALMTHR>

Alarm threshold. Must not be null. The parameter type is ALM_THR, which is the alarm threshold list for MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, MD-4-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

  • ADD-HDEG

ADD Power - High Degrade

  • ADD-HFAIL

ADD Power - High Failure

  • ADD-LDEG

ADD Power - Low Degrade

  • ADD-LFAIL

ADD Power - Low Failure

  • BATV-EHIGH

Battery Voltage—Extremely High

  • BATV-ELOW

Battery Voltage—Extremely Low

  • BATV-HIGH

Battery Voltage—High

  • BATV-LOW

Battery Voltage—Low

  • GAIN-HDEG

Gain not reached—High Degrade Threshold

  • GAIN-HFAIL

Gain not reached—High Failure Threshold

  • GAIN-LDEG

Gain not reached—Low Degrade Threshold

  • GAIN-LFAIL

Gain not reached—Low Failure Threshold

  • LBCL-HIGH

Laser Bias Current in microA as a tenth of a percentage of the High Warning Threshold, Low Warning Threshold. Measured value 0.0%, 100.0%.

  • OPR-HIGH

Receive power in 1tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPR-LOW

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-HIGH

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-LOW

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPWR-HDEG

Optical Power—High Degrade Threshold

  • OPWR-HFAIL

Optical Power—High Failure Threshold

  • OPWR-LDEG

Optical Power—Low Degrade Threshold

  • OPWR-LFAIL

Optical Power—Low Failure Threshold

  • VOA-HDEG

VOA Attenuation—High Degrade Threshold

  • VOA-HFAIL

VOA Attenuation—High Failure Threshold

  • VOA-LDEG

VOA Attenuation—Low Degrade Threshold

  • VOA-LFAIL

VOA Attenuation—Low Failure Threshold

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>”

;

Output Example

TCC2 2011-08-18 16:01:38

M A COMPLD

"VFAC-5-3-1,OTU1:OPT-LOW,,,-4.5,"

;

 

Table 21-22 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section.

<MOD>

AID type. The parameter type is MOD2, which is the line/path modifier.

  • 10GFC

10-Gigabit Fibre Channel payload

  • 10GFICON

10-Gigabit fiber connectivity payload

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 1GISC3

1-Gigabit ISC3 compatible

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 2GISC3

2-Gigabit ISC3 compatible

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • D1VIDEO

D1 video

  • DS1

DS1 line of a DS3XM card

  • DS3I

DS3I line

  • DV6000

DV6000

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • EC1

EC1 facility

  • ESCON

ESCON

  • ETRCLO

ETR_CLO

  • FSTE

FSTE facility

  • G1000

G1000 facility

  • GFPOS

GFP over POS. Virtual ports partitioned using GFP’s multiplexing capability.

  • GIGE

Gigabit Ethernet

  • HDSDI

1.5G HD-SDI video payload.

  • HDTV

HDTV

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • OC3

OC-3 facility

  • OC12

OC-12 facility

  • OC48

OC-48 facility

  • OC192

OC-192 facility

  • OC768

OC-768 facility

  • OCH

Optical Channel

  • OCHCC

OCH client connection

  • OCHNC

OCH network connection

  • OCHTERM

OCH termination

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port

  • SDSDI

270M SDI video payload

  • STS1

STS1 path

  • STS3C

STS3c path

  • STS6C

STS6c path

  • STS9C

STS9c path

  • STS18C

STS18c path

  • STS12C

STS12c path

  • STS24C

STS24c path

  • STS36C

STS36c path

  • STS48C

STS48c path

  • STS192C

STS192c path

  • T1

T1/DS1 facility/line

  • T3

T1/DS1 facility/line

  • VT1

VT1 path

  • VT2

VT2 path

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

  • BATV-EHIGH

Battery Voltage—Extremely High

  • BATV-ELOW

Battery Voltage—Extremely Low

  • BATV-HIGH

Battery Voltage—High

  • BATV-LOW

Battery Voltage—Low

  • GAIN-HDEG

Gain not reached—High Degrade Threshold

  • GAIN-HFAIL

Gain not reached—High Failure Threshold

  • GAIN-LDEG

Gain not reached—Low Degrade Threshold

  • GAIN-LFAIL

Gain not reached—Low Failure Threshold

  • LBCL-HIGH

Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold Measured value [0.0%, 100.0%]

  • OPR-HIGH

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPR-LOW

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-HIGH

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-LOW

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPWR-HDEG

Optical Power—High Degrade Threshold

  • OPWR-HFAIL

Optical Power—High Failure Threshold

  • OPWR-LDEG

Optical Power—Low Degrade Threshold

  • OPWR-LFAIL

Optical Power—Low Failure Threshold

  • VOA-HDEG

VOA Attenuation—High Degrade Threshold

  • VOA-HFAIL

VOA Attenuation—High Failure Threshold

  • VOA-LDEG

VOA Attenuation—Low Degrade Threshold

  • VOA-LFAIL

VOA Attenuation—Low Failure Threshold

<THLEVEL>

Threshold level. THLEVEL is a float.

21.18 RTRV-ALMTH-EQPT

(Cisco ONS 15454 SDH) The Retrieve Alarm Threshold Equipment (RTRV-ALMTH-EQPT) command retrieves the alarm thresholds for the power level monitoring on an NE.

 
Usage Guidelines

None

Category

Equipment

Security

Retrieve

Input Format

RTRV-ALMTH-EQPT:[<TID>]:[<AID]>:<CTAG>::[<CONDTYPE>][,,::];

Input Examples

RTRV-ALMTH-EQPT:::1::BATV-HIGH;

RTRV-ALMTH-EQPT::SHELF-2:1::BATV-HIGH;

 

Table 21-23 Input Parameter Support

Parameter
Description

<AID>

(Optional) The node or shelf access identifier from the “SHELF” section. If omitted, it addresses the node or first shelf of the node.

<CONDTYPE>

Alarm threshold. A null value is equivalent to ALL. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

  • BATV-EHIGH

Battery Voltage—Extremely High

  • BATV-ELOW

Battery Voltage—Extremely Low

  • BATV-HIGH

Battery Voltage—High

  • BATV-LOW

Battery Voltage—Low

  • GAIN-HDEG

Gain not reached—High Degrade Threshold

  • GAIN-HFAIL

Gain not reached—High Failure Threshold

  • GAIN-LDEG

Gain not reached—Low Degrade Threshold

  • GAIN-LFAIL

Gain not reached—Low Failure Threshold

  • LBCL-HIGH

Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold. Measured value [0.0%, 100.0%]

  • OPR-HIGH

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPR-LOW

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-HIGH

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-LOW

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPWR-HDEG

Optical Power—High Degrade Threshold

  • OPWR-HFAIL

Optical Power—High Failure Threshold

  • OPWR-LDEG

Optical Power—Low Degrade Threshold

  • OPWR-LFAIL

Optical Power—Low Failure Threshold

  • VOA-HDEG

VOA Attenuation—High Degrade Threshold

  • VOA-HFAIL

VOA Attenuation—High Failure Threshold

  • VOA-LDEG

VOA Attenuation—Low Degrade Threshold

  • VOA-LFAIL

VOA Attenuation—Low Failure Threshold

Output Format

SID DATE TIME
M CTAG COMPLD
“[<AID>],<MOD2B>:<CONDTYPE>,,,<DNFIELD>”

;

Output Examples

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SHELF-1,EQPT:BATV-HIGH,,,-52.0,”
;

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“,EQPT:BATV-HIGH,,,-52.0,"”
;

 

Table 21-24 Output Parameter Support

Parameter
Description

<AID>

(Optional) The node or shelf access identifier from the “SHELF” section. If omitted, it addresses the node or first shelf of the node.

<MOD2B>

Alarm type. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • BITS

BITS alarm

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 alarm

  • E1

E1 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 alarm

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet Port alarm

  • G1000

G1000 alarm

  • GIGE

Gigabit Ethernet port alarm

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • POS

POS port alarm

  • STM1

STM1 alarm

  • STM1E

STM1E alarm

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • SYNCN

SYNCN alarm

  • TCC

TCC alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC44C

VC44C alarm

  • VC38C

VC38C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

<CONDTYPE>

Alarm threshold. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

  • BATV-EHIGH

Battery Voltage—Extremely High

  • BATV-ELOW

Battery Voltage—Extremely Low

  • BATV-HIGH

Battery Voltage—High

  • BATV-LOW

Battery Voltage—Low

  • GAIN-HDEG

Gain not reached—High Degrade Threshold

  • GAIN-HFAIL

Gain not reached—High Failure Threshold

  • GAIN-LDEG

Gain not reached—Low Degrade Threshold

  • GAIN-LFAIL

Gain not reached—Low Failure Threshold

  • LBCL-HIGH

Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold. Measured value [0.0%, 100.0%].

  • OPR-HIGH

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPR-LOW

Receive power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-HIGH

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPT-LOW

Transmit power in tenths of a microW. Measured value –40.0 dBm, +30.0 dBm.

  • OPWR-HDEG

Optical Power—High Degrade Threshold

  • OPWR-HFAIL

Optical Power—High Failure Threshold

  • OPWR-LDEG

Optical Power—Low Degrade Threshold

  • OPWR-LFAIL

Optical Power—Low Failure Threshold

  • VOA-HDEG

VOA Attenuation—High Degrade Threshold

  • VOA-HFAIL

VOA Attenuation—High Failure Threshold

  • VOA-LDEG

VOA Attenuation—Low Degrade Threshold

  • VOA-LFAIL

VOA Attenuation—Low Failure Threshold

<DNFIELD>

DNFIELD is a float.

21.19 RTRV-ALS

(Cisco ONS 15454 SDH) The Retrieve Automatic Laser Shutoff (RTRV-ALS) command retrieves the ALS attributes of an STM facility and all the facilities that support the ALS feature. This command is used to retrieve the ALS parameter of the STM4, STM16, and STM64 ports on the MXP_2.5G_10E, TXP_MR_10E, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_2.5G_10G, and TXP_MR_10G cards.

 
Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-ALS:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-ALS:PENNGROVE:FAC-1-1:1;

Input Parameters

<AID>

Access identifier from the “AidUnionId” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,<AIDTYPE>::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>],[LSRSTAT=<LSRSTAT>],[OSRI=<OSRI>]”

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“FAC-6-1,STM64::ALSMODE=DISABLED,ALSRCINT=100,ALSRCPW=2.0,LSRSTAT=UP:”
;

 

Table 21-25 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “AidUnionId” section.

<AIDTYPE>

Type of access identifier. The parameter type is MOD2, which is the line/path modifier.

  • 10GFC

10-Gigabit Fibre Channel payload

  • 10GFICON

10-Gigabit fiber connectivity payload

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 1GISC3

1-Gigabit ISC3 compatible

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 2GISC3

2-Gigabit ISC3 compatible

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • D1VIDEO

D1 video

  • DS3I

DS3i-N-12 line

  • DV6000

DV6000

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1

  • E3

E3

  • E4

E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.

  • ESCON

ESCON

  • ETRCLO

ETRCLO

  • FSTE

FSTE facility

  • G1000

G1000 facility

  • GFPOS

Generic Framing Protocol over Packet Over SDH. Virtual ports partitioned using GFP's multiplexing capability.

  • GIGE

Gigabit Ethernet

  • HDTV

HDTV

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gigabit ISC3 Peer

  • ISC3PEER2G

2-Gigabit ISC3 Peer

  • ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

  • OCH

Optical Channel

  • OCHCC

OCH client connection

  • OCHNC

OCH network connection

  • OCHTERM

OCH termination

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • POS

POS port

  • STM1

STM1 facility

  • STM1E

STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card

  • STM4

STM4 facility

  • STM16

STM16 facility

  • STM64

STM64 facility

  • VC3

VC3 path

  • VC44C

VC4-4C path

  • VC38C

VC3-8C path

  • VC464C

VC4-64C path

  • VC48C

VC4-8C path

  • VC4

VC4 path

  • VC416C

VC4-16C path

  • VC42C

VC4-2C path

  • VC43C

VC4-3C path

  • VC11

VC11 path

  • VC12

VC12 path

<ALSMODE>

(Optional) ALS is enabled or disabled. The parameter type is ALS_MODE, which is the working mode for automatic laser shutdown.

  • AUTO

Automatic

  • DISABLED

Disabled

  • MAN

Manual

  • MAN-RESTART

Manual restart for test

<ALSRCINT>

(Optional) ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer.

<ALSRCPW>

(Optional) ALS recovery pulse width. The range is 2.0 to 100.00 seconds, in increments of 100 ms. ALSRCPW is a float.

<LSRSTAT>

(Optional) Status of the laser. The parameter type is LASER_STATUS, which is the status of laser.

  • APR

Laser is switched on but is working automatic power reduction.

  • OFF

Laser is switched off.

  • ON

Laser is switched on.

<OSRI>

(Optional) OSRI enabled or disabled. Present only on a port where the safety is supported. Defaults to off. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

21.20 RTRV-APC

(Cisco ONS 15454 SDH) The Operate Amplifier Power Control (RTRV-APC) command retrieves the APC application attributes.

 
Usage Guidelines

None

Category

DWDM

Security

Maintenance

Input Format

RTRV-APC:[<TID>]::<CTAG>;

Input Example

RTRV-APC:PENNGROVE:WDMSIDE-A:114;

Input Parameters

None

Output Format

SID DATE TIME
M CTAG COMPLD
“:[ROLE=<ROLE>],[APCENABLE=<APCENABLE>],[APCSTATE=<APCSTATE>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“::APCENABLE=Y,APCSTATE=WORKING”
;

 

Table 21-26 Output Parameter Support

Parameter
Description

<WDMSIDE>

The AID is used to access the WDM side of an MSTP node.

  • WDMSIDE-{UNKNOWN,A,B,C,D,E,F,G,H}

MSTP side identifier

<ROLE>

The role the unit is playing in the protection group.

  • PROT

The entity is the protection unit in the protection group.

  • WORK

The entity is the working unit in the protection group.

<APCENABLE>

(Optional) Enable or disable of the APC application. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

<APCSTATE>

(Optional) Indicates the status of the APC application. The parameter type is APC_STATE, which is the APC status.

  • DISABLE

The APC is disabled by the user and is not working.

  • FORCED-DISABLE

The APC has been internally disabled by the node and is not working.

  • WORKING

The APC is enabled by the user and is working.

  • PASSIVE

The APC is in the passive state.

21.21 RTRV-ATTR-CONT

(Cisco ONS 15454 SDH) The Retrieve Attribute Control (RTRV-ATTR-CONT) command retrieves and sends the attributes associated with an external control. These attributes are used when an external control is operated or released. To set these attributes, use the SET-ATTR-CONT command.

 
Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];

Input Example

RTRV-ATTR-CONT:CISCO:ENV-OUT-2:123::AIRCOND;

 

Table 21-27 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section. Identifies the external control for which attributes are being set.

<CONTTYPE>

(Optional) Environmental control type. A null value is equivalent to ALL. The parameter type is CONTTYPE, which is the environmental control type.

  • AIRCOND

Air conditioning

  • ENGINE

Engine

  • FAN

Fan

  • GEN

Generator

  • HEAT

Heat

  • LIGHT

Light

  • MISC

Miscellaneous

  • SPKLR

Sprinkler

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:[<CONTTYPE>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“ENV-OUT-2:AIRCOND”
;

 

Table 21-28 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section. Identifies the external control for which attributes are being set.

<CONTTYPE>

(Optional) Environmental control type. A null value is equivalent to ALL. The parameter type is CONTTYPE, which is the environmental control type.

  • AIRCOND

Air conditioning

  • ENGINE

Engine

  • FAN

Fan

  • GEN

Generator

  • HEAT

Heat

  • LIGHT

Light

  • MISC

Miscellaneous

  • SPKLR

Sprinkler

21.22 RTRV-ATTR-ENV

(Cisco ONS 15454 SDH) The Retrieve Attribute Environment (RTRV-ATTR-ENV) command retrieves the attributes associated with an environmental alarm.

 
Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];

Input Example

RTRV-ATTR-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;

 

Table 21-29 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section.

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

  • AIRCOMPR

Air compressor failure

  • AIRCOND

Air conditioning failure

  • AIRDRYR

Air dryer failure

  • BATDSCHRG

Battery discharging

  • BATTERY

Battery failure

  • CLFAN

Cooling fan failure

  • CPMAJOR

Centralized power major failure

  • CPMINOR

Centralized power minor failure

  • ENGINE

Engine failure

  • ENGOPRG

Engine operating

  • ENGTRANS

Standby engine transfer

  • EXPLGS

Explosive gas

  • FIRDETR

Fire detector failure

  • FIRE

Fire

  • FLOOD

Flood

  • FUELLEAK

Fuel leak

  • FUSE

Fuse failure

  • GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

  • HATCH

CEV hatch fail

  • GEN

Generator failure

  • HIAIR

High air flow

  • HIHUM

High humidity

  • HITEMP

High temperature

  • HIWTR

High water

  • INTRUDER

Intrusion

  • LEVELCON

Level converter

  • LVDADSL

Secondary ADSL low voltage disconnect

  • LVDBYPAS

Low voltage disconnect bypass

  • LWBATVG

Low battery voltage

  • LWFUEL

Low fuel

  • LWHUM

Low humidity

  • LWPRES

Low cable pressure

  • LWTEMP

Low temperature

  • LWWTR

Low water

  • MISC

Miscellaneous

  • OPENDR

Open door

  • POWER

Commercial power failure

  • PUMP

Pump failure

  • PWR-48

48 V power supply failure

  • PWR-139

–139 V power converter

  • PWR-190

–190 V power converter

  • PWRMJ

Power supply major

  • PWRMN

Power supply minor

  • RECT

Rectifier failure

  • RECTHI

Rectifier high voltage

  • RECTLO

Rectifier low voltage

  • RINGGENMJ

Ringing generator major

  • RINGGENMN

Ringing generator minor

  • RTACADSL

AC or AC/rectifier power fail ADSL equipment

  • RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

  • RTACPWR

AC or AC/rectifier power fail DCL equipment

  • RTACPWRENG

Commercial AC fail, site equipped with standby engine

  • RTBAYPWR

AC power loss distributed power RT bay

  • RTRVENG

Retrieve standby engine, commercial AC restored

  • SMOKE

Smoke

  • TEMP

High-low temperature

  • TOXICGAS

Toxic gas

  • TREPEATER

T-repeater shelf

  • VENTN

Ventilation system failure

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“ENV-IN-1:MJ,OPENDR,\“OPEN DOOR\””
;

 

Table 21-30 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section.

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. The parameter type is ENV_ALM, which is the environmental alarm type.

  • AIRCOMPR

Air compressor failure

  • AIRCOND

Air conditioning failure

  • AIRDRYR

Air dryer failure

  • BATDSCHRG

Battery discharging

  • BATTERY

Battery failure

  • CLFAN

Cooling fan failure

  • CPMAJOR

Centralized power major failure

  • CPMINOR

Centralized power minor failure

  • ENGINE

Engine failure

  • ENGOPRG

Engine operating

  • ENGTRANS

Standby engine transfer

  • EXPLGS

Explosive gas

  • FIRDETR

Fire detector failure

  • FIRE

Fire

  • FLOOD

Flood

  • FUELLEAK

Fuel leak

  • FUSE

Fuse failure

  • GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

  • HATCH

CEV hatch fail

  • GEN

Generator failure

  • HIAIR

High air flow

  • HIHUM

High humidity

  • HITEMP

High temperature

  • HIWTR

High water

  • INTRUDER

Intrusion

  • LEVELCON

Level converter

  • LVDADSL

Secondary ADSL low voltage disconnect

  • LVDBYPAS

Low voltage disconnect bypass

  • LWBATVG

Low battery voltage

  • LWFUEL

Low fuel

  • LWHUM

Low humidity

  • LWPRES

Low cable pressure

  • LWTEMP

Low temperature

  • LWWTR

Low water

  • MISC

Miscellaneous

  • OPENDR

Open door

  • POWER

Commercial power failure

  • PUMP

Pump failure

  • PWR-48

48 V power supply failure

  • PWR-139

–139 V power converter

  • PWR-190

–190 V power converter

  • PWRMJ

Power supply major

  • PWRMN

Power supply minor

  • RECT

Rectifier failure

  • RECTHI

Rectifier high voltage

  • RECTLO

Rectifier low voltage

  • RINGGENMJ

Ringing generator major

  • RINGGENMN

Ringing generator minor

  • RTACADSL

AC or AC/rectifier power fail ADSL equipment

  • RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

  • RTACPWR

AC or AC/rectifier power fail DCL equipment

  • RTACPWRENG

Commercial AC fail, site equipped with standby engine

  • RTBAYPWR

AC power loss distributed power RT bay

  • RTRVENG

Retrieve standby engine, commercial AC restored

  • SMOKE

Smoke

  • TEMP

High-low temperature

  • TOXICGAS

Toxic gas

  • TREPEATER

T-repeater shelf

  • VENTN

Ventilation system failure

<DESC>

(Optional) Alarm description. DESC is a string.

21.23 RTRV-AUDIT-LOG

(Cisco ONS 15454 SDH) The Retrieve Audit Log (RTRV-AUDIT-LOG) command retrieves the contents of the audit log stored in the NE. Audit records contain information for user operations such as login, logout, change of provisioning parameters and other changes a user might make when connected to the NE. Audit records do not store operations related to parameter retrieval.

 
Usage Guidelines

None

Category

Log

Security

Superuser

Input Format

RTRV-AUDIT-LOG:[<TID>]::<CTAG>;

Input Example

RTRV-AUDIT-LOG:::1;

Input Parameters

None

Output Format

SID DATE TIME
M CTAG COMPLD
“ <ENTRYNUM>,<OCRDAT>,<OCRTM>,<TASKID>,<TXSTATUS>,<DESCRIPTION>”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“17172,2004-10-05,09-52-44, TPROVMGR,COMPLD,\"DESCRIPTION\””
;

 

Table 21-31 Output Parameter Support

Parameter
Description

<ENTRYNUM>

Entry number. ENTRYNUM is an integer.

<OCRDAT>

Date when the specific event or violation occurred, MM-DD.

<OCRTM>

Time when the specific event or violation occurred, HH-MM-SS.

<TASKID>

Task ID. TASKID is a string.

<TXSTATUS>

The parameter type is TX_STATUS, which indicates the status of the transferred file.

  • COMPLD

The file transmission is completed.

  • IP

The file transmission is in process.

  • START

The file transmission is started.

<DESCRIPTION>

Description of event. The description format varies depending on the event and can include parameters used during the event. DESCRIPTION is a string.

21.24 RTRV-AUTO

( Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Retrieve Auto (RTRV-AUTO) command retrieves the AUTO ports provisioned. Port bandwidth changes to OC3/OC12/OC48 as per the incoming signal when auto sense is enabled. Default being OC48 when auto sense is disabled.

 
Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

RTRV-AUTO:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-AUTO:CISCO:VFAC-2-1-1:1;

Input Parameters

None that require description

Output Format

SID DATE TIME

M CTAG COMPLD

"<AID>,[DETECTEDPAYLOAD=<DETECTEDPAYLOAD>],[AUTOSENSE=<AUTOSENSE>]"

;

Output Example

M 1 COMPLD

"VFAC-15-1-1,DETECTEDPAYLOAD=OC48,AUTOSENSE=N"

;

Output Parameters

<AID>

The AR-MXP and AR-XP cards use the VFAC Access Identifier.

<DETECTEDPAYLOAD>

Payload detected.

  • 3GVIDEO

3G-SDI video payload.

  • AUTO

Auto.

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • HDSDI

1.5G HD-SDI video payload.

  • OTU1

Optical Transport Unit Level 1.

  • SDSDI

270M SDI video payload.

<AUTOSENSE>

Specifies if auto sense is enabled or disabled.

  • Y

Enable Autosensing.

  • N

Disable Autosensing.

21.25 RTRV-BITS

(Cisco ONS 15454 SDH) The Retrieve Building Integrated Timing Supply (RTRV-BITS) command retrieves the BITS configuration command.

 
Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-BITS:SONOMA:BITS-1:782;

Input Parameters

<AID>

Access identifier from the “BITS” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[IMPEDANCE=<IMPEDANCE>],[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>]:[<PST>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“BITS-1::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,AISTHRSHLD=G811,
SABIT=BYTE-4,IMPEDANCE=120-OHM,BITSFAC=E1,ADMSSM=G811:UNLOCKED”
;

 

Table 21-32 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “BITS” section.

<LINECDE>

(Optional) Line code. The parameter type is LINE_CODE (line code).

  • AMI

Line code value is AMI.

  • B8ZS

Line code value is B8ZS (bipolar with eight-zero substitution).

  • HDB3

Line Code HDB3. Only applicable to SDH E1 signal.

<FMT>

(Optional) Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.

  • E1-CRCMF

SDH E1 CRCMF frame format

  • E-CRC

SDH E1 CRC frame format

  • E1-MF

SDH E1 MF frame format

  • E1-UNFRAMED

SDH E1 unframed format

  • E1-FRAME

SDH E1 framed format

<LBO>

(Optional) BIS line build out settings. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line buildout).

  • 0–133

BITS line buildout range is 0 to 133.

  • 134–266

BITS line buildout range is 134 to 266.

  • 267–399

BITS line buildout range is 267 to 399.

  • 400–533

BITS line buildout range is 400 to 533.

  • 534–655

BITS line buildout range is 534 to 655.

<SYNCMSG>

(Optional) Indicates if the BITS facility supports synchronization status message. Default is on (Y). The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

  • N

The ring does not support the extended K1/K2/K3 protocol.

  • Y

The ring does support the extended K1/K2/K3 protocol.

<AISTHRSHLD>

(Optional) Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

  • DUS_SDH

Do Not Use For Synchronization

  • G811

ITU-T G.811 Standard

  • RES_SDH

Reserved For Network Synchronization Use

  • G812T

ITU-T G.812T Standard

  • STU_SDH

Synchronized, Traceability Unknown

  • G812TL

ITU-T G.812TL Standard

  • SETS

Synchronous Equipment Timing Source

<SABIT>

(Optional) When the frame format selection is E1, SABIT is the BIT used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).

  • BYTE-4

SABIT is BYTE-4.

  • BYTE-5

SABIT is BYTE-5.

  • BYTE-6

SABIT is BYTE-6.

  • BYTE-7

SABIT is BYTE-7.

  • BYTE-8

SABIT is BYTE-8.

<IMPEDANCE>

(Optional) When the frame format selection is E1, IMPEDANCE is the terminal impedance of the BITS-IN port. The parameter type is IMPEDANCE, which is the terminal impedance of the BITS-IN port.

  • 120-OHM

Impedance of 120 ohm

  • 75-OHM

Impedance of 75 ohm

<BITSFAC>

(Optional) BITS facility settings. The parameter type is BITS_FAC, which is the BITS facility rate. 64 k and 6 MHz are only applicable to SDH.

  • 2 M

2 MHz rate

  • 64 K

64 K rate

  • 6 M

6 MHz rate

  • E1

E1 rate

<ADMSSM>

(Optional) SSM selectable. Only applicable to BITS-IN when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

  • DUS_SDH

Do Not Use For Synchronization

  • G811

ITU-T G.811 Standard

  • RES_SDH

Reserved For Network Synchronization Use

  • G812T

ITU-T G.812T Standard

  • STU_SDH

Synchronized, Traceability Unknown

  • G812TL

ITU-T G.812TL Standard

  • SETS

Synchronous Equipment Timing Source

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

  • Unlocked

In service

  • Locked

Out of service

21.26 RTRV-BULKROLL-<STM_TYPE>

(Cisco ONS 15454 SDH) The Retrieve Bulkroll for STM4, STM64, STM1, or STM16 (RTRV-BULKROLL-STM_TYPE>) command retrieves roll data parameters on a line. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

None

Category

Bridge and Roll

Security

Retrieve

Input Format

RTRV-BULKROLL-<OCN_TYPE>:[<TID>]:<SRC>:<CTAG>:::[CRSTYPE=<CRSTYPE>];

Input Example

RTRV-BULKROLL-STM4:CISCO:FAC-3-1:1:::VC3;

Input Parameters

<SRC>

Source AID from the “FACILITY” section.

<CRSTYPE>

One of the values: VC3, VC44C, VC38C, VC464C, VC48C, VC4-12C, VC4, VC416C, VC42C, VC43C, VC11, or VC12

Output Format

SID DATE TIME
M CTAG COMPLD
“<FROM>:RFROM=<RFROM>,RTO=<RTO>,RMODE=<RMODE>,VLDSIG=<VLDSIG>”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“VC4-3-1-1:RFROM=VC4-3-1-1,RTO=VC4-5-1-1,RMODE=AUTO,VLDSIG=Y”
;

 

Table 21-33 Output Parameter Support

Parameter
Description

<FROM>

One of the endpoints. Access identifier from the “FACILITY” section for line level rolling and bulk rolling.

<RFROM>

The termination point of the existing cross-connect that is to be rolled. AID is from the “VC” section.

<RTO>

The the termination point that will become a leg of the new cross-connection. AID is from the “VC” section.

<RMODE>

(Optional) The rolling mode of operation. The parameter type is RMODE, which specifies the roll mode.

  • AUTO

Automatic. When a valid signal is available, the roll under AUTO mode will automatically delete the previous endpoint.

  • MAN

Manual. Enter the corresponding delete roll/bulkroll command to delete the previous endpoint.

<VLDSIG>

(Optional) The rolling mode of operation. The parameter type is ON_OFF (disable or enable an attribute).

  • N

Disable an attribute.

  • Y

Enable an attribute.

21.27 RTRV-BWP-ETH

(Cisco ONS 15454SDH)

This command is used to retrieve a BandWidth Profile entry in BWP DB. The BWP DB is a collection of BWP used in a Network Element.

 
Usage Guidelines

The “ALL” AID is supported by this command.

If the AID is invalid, an IIAC (Invalid AID) error message is returned.

Category

Ethernet

Security

Retrieve

Input Format

RTRV-BWP-ETH:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-BWP-ETH:ROCKS:BWP-10000:1;

Input Parameter

 

Table 21-34 Input Parameter Support

Parameter
Description

<AID>

This AID is used to access BWP.

  • BWP-ALL

All aid for BWP.

  • BWP-{1-10000}

Single AID for BWP. The valid identifiers ranges from 1 to 10000.

Output Format

SID DATE TIME

M CTAG COMPLD

"<AID>::[NAME=<NAME>],[CIR=<CIR>],[CBS=<CBS>],[PBS=<PBS>],[PIR=<PIR>],[CFMSTATE=<CFM_STATE>]:";

;

Output Example

TID-000 1998-06-20 14:30:00

M 001 COMPLD

"BWP-10000::NAME="MyBWP",CIR=10,CBS=1M,PBS=1M,PIR=20,CFMSTATE=Y:";
;

Output Parameters

Table 21-35 Output Parameter Support

Parameter
Description

<AID>

This AID is used to access BWP.

  • BWP-ALL

All aid for BWP.

  • BWP-{1-10000}

Single AID for BWP. The valid identifiers ranges from 1 to 10000.

<NAME>

The BWP name. BWP name is a String.

<CIR>

Ingress committed information rate. This is a value between 0 and 100. Default value is - 100.

<CBS>

Ingress committed burst bucket size.

  • 4K

4 Kbit bucket size

  • 8K

16 Kbit bucket size

  • 16K

32 Kbit bucket size

  • 32K

64 Kbit bucket size

  • 64K

128 Kbit bucket size

  • 128K

256 Kbit bucket size

  • 256K

512 Kbit bucket size

  • 512K

1 Mbit bucket size

  • 1M

2 Mbit bucket size

  • 2M

4 Mbit bucket size

  • 4M

8 Mbit bucket size

  • 8M

16 Mbit bucket size

  • 16M

16 Kbit bucket size

<PBS>

Ingress peak burst bucket size

  • 4K

4 Kbit bucket size

  • 8K

8 Kbit bucket size

  • 16K

16 Kbit bucket size

  • 32K

32 Kbit bucket size

  • 64K

64 Kbit bucket size

  • 128K

128 Kbit bucket size

  • 256K

256 Kbit bucket size

  • 512K

512 Kbit bucket size

  • 1M

1 Mbit bucket size

  • 2M

2 Mbit bucket size

  • 4M

4 Mbit bucket size

  • 8M

8 Mbit bucket size

  • 16M

16 Mbit bucket size

<PIR>

Peak information rate. This is a value between 0 and 100. Default value is - 100.

<CFMSTATE>

Link Integrity status

  • Y

Enabled

  • N

Disabled

21.28 RTRV-CFM

(Cisco ONS 15454 SDH) The Retrieve Connectivity Fault Management (RTRV-CFM) command retrieves the Connectivity Fault Management (CFM) protocol state at the port level.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Port

Security

Retrieve

Input Format

RTRV-CFM:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-CFM:454-156:ETH-1-1-1:1;

Input Parameter

Table 21-36

<AID>

Access identifier from the “ETH” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,<STATE>”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“ETH-7-1-1,STATE=ENABLE”
;

 

Table 21-37 Output Parameter Support

Parameter
Description

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the “ETH” section.

<CFM_STATE>

Indicates whether the CFM is enabled or disabled on the port.

  • ENABLE

Indicates the CFM is enabled on the port.

  • DISABLE

Indicates the CFM is disabled on the port.

21.29 RTRV-CHGRP

(Cisco ONS 15454 SDH) The Retrieve Channel Group (RTRV-CHGRP) command retrieves the layer 2 channel group information of GE_XP and 10GE_XP ethernet cards.

Category

Channel Group

Security

Retrieve

Input Format

RTRV-CHGRP:[<TID>]:<aid>:<CTAG>[::::];

Input Example

RTRV-CHGRP::CHGRP-1-2:1;

Input Parameters

<AID>

Access identifier from the “CHGRP” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:[LACPMODE=<LACPMODE>],[HASHINGALGO=<HASHINGALGO>],[NIMODE=<NIMODE>],[MACLEARNING=<MACLEARNING>],[INGRESSCOS=<INGRESSCOS>],[ETHERCETYPE=<ETHERCETYPE>],[ETHERSTYPE=>ETHERSTYPE>],[BPDU=<BPDU>],[QNQMODE=<QNQMODE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>],[SPEED=<SPEED>],[EXPSPEED=<EXPSPEED>],[CIR=<CIR>,[CBS=<CBS>],[EBS=<EBS>]:<PST>,[<SST>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“CHGRP-1-1:LACPMODE=ACTIVE,HASHINGALGO=HASHING_SA_DA_VLAN_INCOMING_PORT,NIMODE=UNI,MACLEARNING=N,INGRESSCOS=0,ETHERCETYPE=8100,ETHERSTYPE
=8100,BPDU=Y,QNQMODE=SELECTIVE,MTU=9700,FLOWCTRL=ASYMMETRIC,
SPEED=AUTO,EXPSPEED=AUTO,CIR=100,CBS=4K,EBS=4K:OOS-MA,DSBLD”
;

 

Table 21-38 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “CHGRP” section.

<NIMODE>

Identifies the Ethernet Network Interface Mode.

  • NNI

(Default) Network-Network Interface Mode

  • UNI

User-Network Interface Mode

<LACPMODE>

LACP mode values

  • ON

Manual mode of LACP

  • ACTIVE

Active mode of LACP

  • PASSIVE

Passive mode of LACP

<HASHINGALGO>

Hashing algorithm value

  • HASHING_SA_VLAN_INCOMING_PORT

The Hashing Algorithm value is HASHING_SA_VLAN_INCOMING_PORT.

  • HASHING_DA_VLAN_INCOMING_PORT

The Hashing Algorithm is HASHING_DA_VLAN_INCOMING_PORT.

  • HASHING_SA_DA_VLAN_INCOMING_PORT

The Hashing Algorithm is HASHING_SA_DA_VLAN_INCOMING_PORT.

  • HASHING_SRC_IP_TCP_UDP

The Hashing Algorithm is HASHING_SRC_IP_TCP_UDP.

  • HASHING_DST_IP_TCP_UDP

The Hashing Algorithm is HASHING_DST_IP_TCP_UDP

  • HASHING_SRC_DST_ IP_TCP_UDP

The Hashing Algorithm is HASHING_SRC_DST_IP_TCP_UDP.

<MTU>

(Optional) Maximum transport unit. The parameter type is MTU_TYPE, which indicates the maximum transport unit used by an Ethernet card. Defaults to 9600.

  • 10004

10004. Indicates jumbo size.

  • 1500

1500

  • 1548

1548

  • 9600

9600. Indicates jumbo size.

  • 64

64

  • 9700

9700. Indicates jumbo size.

<ATTACH >

Ethernet AID for the front end CE-MR-6 cards. Ethernet AID for the ethernet port on GE_XP and 10GE_XP card.

<DETACH>

To remove or detach the port.

<SPEED>

(Optional) The parameter type is ETHER_SPEED, which indicates Ethernet speed. Defaults to AUTO.

  • 100_MBPS

100 Megabits per second

  • 10_GBPS

10 Gigabits per second

  • 10_MBPS

10 Megabits per second

  • 1_GBPS

1 Gigabit per second

  • 40_GBPS

40 Gigabit per second

  • AUTO_FDX

Enable auto negotiation with full duplex.

<EXPSPEED>

(Optional) Ethernet speed. The parameter type is ETHER_SPEED, which is the Ethernet speed.

  • 100_MBPS

100 Megabits per second

  • 10_GBPS

10 Gigabits per second

  • 10_MBPS

10 Megabits per second

  • 1_GBPS

1 Gigabit per second

  • AUTO

Auto

<CIR>

Ingress committed information rate. The value ranges from 0 to 100. The default value is 100.

<CBS>

Ingress committed burst bucket size.

  • 4K

4 Kbit bucket size

  • 8K

16 Kbit bucket size

  • 16K

32 Kbit bucket size

  • 32K

64 Kbit bucket size

  • 64K

128 Kbit bucket size

  • 128K

256 Kbit bucket size

  • 256K

512 Kbit bucket size

  • 512K

1 Mbit bucket size

  • 1M

2 Mbit bucket size

  • 2M

4 Mbit bucket size

  • 4M

8 Mbit bucket size

  • 8M

16 Mbit bucket size

  • 16M

16 Kbit bucket size

<EBS>

Ingress excess burst bucket size.

<MACLEARNING>

MAC Address Learning Mode. This activates the MAC address learning on the interface to avoid packet broadcasting.

  • Y

Enables the MAC learning on the interface.

  • N

Disables the MAC learning on the interface.

<INGRESSCOS>

Identifies the COS value set in the S-VLAN tag.

  • 0 to 7

Set a Cos value

  • TRUST

Use the Customer COS

  • VLAN

The COS will be provisioned on CVLAN basis (QinQ selective mode)

<ETHERCETYPE>

Identifies a customer foreseen Ethernet type. If the customer uses a non-standard Ethernet type, the incoming packets will be accepted only if the CE-VLAN Ethernet type matches this parameter.

<ETHERSTYPE>

Identifies a customer foreseen Ethernet type. If the customer uses a non-standard Ethernet type, the incoming packets will be accepted only if the CE-VLAN Ethernet type matches this parameter.

<BPDU>

BPDU (Bridge Protocol Data Unit) management mode; Drop/Passthrough BPDU tagged packets.

  • Y

Enables the BPDU tag.

  • N

Disables the BPDU tag.

<QNQMODE>

This is used to represent the QinQ mode operations.

  • Selective

The S-VLAN tag is added only on specified CE-VLANs. The other packets are dropped.

  • Transparent

The S-VLAN tag is always performed where all packets having the S-VLAN-ID identified by TRNSPSVLAN parameter are allowed.

<TRNSPSVLAN>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

<NAME>

(Optional) NAME is a string. User-assigned port name.

21.30 RTRV-CMD-SECU

(Cisco ONS 15454 SDH) The Retrieve Command Security (RTRV-CMD-SECU) command retrieves the current command security level of the command specified in the AID field.

 
Usage Guidelines

None

Category

Security

Security

Superuser

Input Format

RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-CMD-SECU::INIT-REG:1;

Input Parameters

<AID>

Access identifier string. Identifies the entity in the NE to which the command pertains. It is the command verb along with verb modifier(s), as it currently exists. It can be a single command or a block of commands, where the block might include all commands. Only INIT-REG will be supported. AID is a string.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:<CAP>”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“INIT-REG:PROV”
;

 

Table 21-39 Output Parameter Support

Parameter
Description

<AID>

Access identifier. It can be a single command or a block of commands, where the block can include all commands. Only INIT-REG is supported. AID is a string.

<CAP>

Command access privilege. The parameter type is PRIVILEGE, which is the security level.

  • PROV

Provision security level

  • SUPER

Superuser security level

21.31 RTRV-COND-<MOD2ALM>

(Cisco ONS 15454 SDH) The Retrieve Condition for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 5GIB, 8GFC, CHGRP, DS1, DS3I, DVBASI, E1, E100, E1000, E3, E4, EC1, FSTE, G1000, ETH, GFPOS, GIGE, HDLC, ILK, ISCCOMPAT, ISC1, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, MSISC, OCH, OMS, OTS, OTU2, OTU3, POS, RPRIF, STM1, STM4, STM16, STM64, STM1E, VC3, VC4-4C, VC4-6C, VC4-64C, VC4-8C, VC4-12C, VC4, VC4-16C, VC4-2C, VC4-3C, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c,VC4-64c, VC11, VC12, VCG, VC11, VC12, WLEN, 3GVIDEO, HDSDI, ISC3STP1G, ISC3STP2G, OTU1, or SDSDI (RTRV-COND-<MOD2ALM>) command retrieves the current standing condition and state associated with an entity.

 
Usage Guidelines

The command supports the modifiers 3GVIDEO, OTU1, SDSDI, HDSDI, ISC3STP1G, and ISC3STP2G.

See Table 27-1 for supported modifiers by platform.

Category

Fault

Security

Retrieve

Input Format

RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

Cisco ONS 15454 SDH

RTRV-COND-OTU1::VFAC-14-3-1:1::OTUK-IAE;

 

Table 21-40 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section. The AR-MXP and AR-XP cards use the VFAC Access Identifier.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME

M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"

;

Output Example

tcc2 2011-08-18 16:11:55

M 1 COMPLD

"VFAC-14-3-1,OTU1:MN,OTUK-IAE,NSA,08-18,12-58-24,NEND,RCV,\"OTUK: INCOMING ALIGNMENT ERROR\""

;

 

Table 21-41 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section

<AIDTYPE>

(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2ALM—alarm type

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 1GISC3

1-Gigabit ISC3 compatible

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • CLNT

Client facility for MXP/TXP cards

  • CHGRP

Channel group

  • DS3I

DS3i-N-12 alarm

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 frame. Only applicable to STM1E port 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode

  • ETH

ETH facility

  • FSTE

Fast Ethernet port alarm

  • G1000

G1000 alarm

  • GFPOS

Generic framing protocol over packet over SDH virtual port alarm

  • GIGE

Gigabit Ethernet port alarm

  • HDSDI

1.5G HD-SDI video payload.

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gbps ISC3 Peer

  • ISC3PEER2G

2-Gbps ISC3 Peer

  • ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OCHTERM

OCH termination

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port alarm

  • REP

Resilient Ethernet Protocol

  • SDSDI

270M SDI video payload.

  • STM1

STM1 alarm

  • STM1E

STM1E facility, only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC38C

VC38C alarm

  • VC44C

VC44C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

  • UDCDCC

UDCDCC alarm

  • UDCF

UCDF alarm

  • VCG

Virtual concatenation group alarm

  • WLEN

Wavelength path provisioning

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<TYPEREP>

The condition itself. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRECTION>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.

21.32 RTRV-COND-ALL

(Cisco ONS 15454 SDH) The Retrieve Condition All (RTRV-COND-ALL) command retrieves the current standing condition for all entities .

 
Usage Guidelines

This command does not return all conditions that are returned by other, more specific RTRV-COND commands; RTRV-COND-ALL returns a subset of these conditions. Telcordia GR-253-CORE, Section 6.2.1.8.4 states that a retrieval that returns ALL conditions from a node (RTRV-COND-ALL) must omit any conditions that have the same root cause as other raised conditions. The section also states that any retrieval of a subset of the conditions from a node, regardless of how the subsetting occurs, should not omit these same-root-cause conditions. So, for example, RTRV-COND-VC3 includes the same-root-cause conditions in the set it returns and, RTRV-COND-ALL does not.

To retrieve all of the NE conditions, issue all of the following commands:

RTRV-COND-ALL
RTRV-COND-ENV
RTRV-COND-BITS
RTRV-COND-SYNCN

Category

Fault

Security

Retrieve

Input Format

RTRV-COND-ALL:[<TID>]:[<AID>]:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

Cisco ONS 15454 SDH

RTRV-COND-ALL:DXT:ALL:229::LOS;

 

Table 21-42 Input Parameter Support

Parameter
Description

<AID>

(Optional) Access identifier from the “ALL” section. AID is a string. A null value is equivalent to ALL.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>],[<DESC>]”
;

Output Example

Cisco ONS 15454 SDH

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“RPRIF-2-0,T3:MJ,FORCE-REQ,SA,01-01,16-00-20,NEND,RCV,\"FORCED SWITCH REQUEST\””
;

 

Table 21-43 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section for the entity that has an alarm condition.

<AIDTYPE>

(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

BITS alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 alarm

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 alarm

  • ETH

ETH facility

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet port alarm

  • G1000

G1000 alarm

  • GIGE

Gigabit Ethernet port alarm

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gbps ISC3 Peer

  • ISC3PEER2G

2-Gbps ISC3 Peer

  • ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port alarm

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 alarm

  • STM1E

STM1E alarm

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • SYNCN

SYNCN alarm

  • TCC

TCC alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC44C

VC44C alarm

  • VC38C

VC38C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed

  • NR

The alarm is not reported

<TYPEREP>

The type of condition to be retrieved. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRECTION>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.

21.33 RTRV-COND-BITS

(Cisco ONS 15454 SDH) The Retrieve Condition Building Integrated Timing Supply (RTRV-COND-BITS) command retrieves the standing conditions on BITS.

 
Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

RTRV-COND-BITS:TID:BITS-1:229::LOS;

 

Table 21-44 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “BITS” section.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>],[<DESC>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“BITS-1,BITS:CR,LOS,SA,01-01,16-02-15,,,\“LOS OF SIGNAL\””
;

 

 

Table 21-45 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “BITS” section.

<AIDTYPE>

(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

Bits facility

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • DS3I

DS3i-N-12 facility

  • E1

E1 facility

  • E3

E3 facility

  • E100

E100 facility

  • E1000

E1000 facility

  • E4

E4 facility

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet port facility

  • G1000

G1000 facility

  • GIGE

Gigabit Ethernet port facility

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC3PEER1G

1-Gbps ISC3 Peer

  • ISC3PEER2G

2-Gbps ISC3 Peer

  • ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port facility

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 facility

  • STM1E

STM1E facility

  • STM4

STM4 facility

  • STM16

STM16 facility

  • STM64

STM64 facility

  • TCC

TCC facility

  • VC11

VC11 path

  • VC12

VC12 path

  • VC3

VC3 path

  • VC44C

VC44C path

  • VC38C

VC38C path

  • VC464C

VC464C path

  • VC48C

VC48C path

  • VC4

VC4 path

  • VC416C

VC416C path

  • VC42C

VC42C path

  • VC43C

VC43C path

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.

21.34 RTRV-COND-ENV

(Cisco ONS 15454 SDH) The Retrieve Environmental Condition (RETRV-COND-ENV) command retrieves the environmental conditions.

 
Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>],[<LOCN>],
<DIRN>];

Input Example

RTRV-COND-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;

 

Table 21-46 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section.

Note For RTRV-ALM-ENV, only ENV-IN-{1-4} is a valid AID for ONS 15454 SDH. ENV-OUT-{1,6} is not a valid AID for RTRV-ALM-ENV.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

  • AIRCOMPR

Air compressor failure

  • AIRCOND

Air conditioning failure

  • AIRDRYR

Air dryer failure

  • BATDSCHRG

Battery discharging

  • BATTERY

Battery failure

  • CLFAN

Cooling fan failure

  • CPMAJOR

Centralized power major failure

  • CPMINOR

Centralized power minor failure

  • ENGINE

Engine failure

  • ENGOPRG

Engine operating

  • ENGTRANS

Standby engine transfer

  • EXPLGS

Explosive gas

  • FIRDETR

Fire detector failure

  • FIRE

Fire

  • FLOOD

Flood

  • FUELLEAK

Fuel leak

  • FUSE

Fuse failure

  • GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

  • HATCH

CEV hatch fail

  • GEN

Generator failure

  • HIAIR

High air flow

  • HIHUM

High humidity

  • HITEMP

High temperature

  • HIWTR

High water

  • INTRUDER

Intrusion

  • LEVELCON

Level converter

  • LVDADSL

Secondary ADSL low voltage disconnect

  • LVDBYPAS

Low voltage disconnect bypass

  • LWBATVG

Low battery voltage

  • LWFUEL

Low fuel

  • LWHUM

Low humidity

  • LWPRES

Low cable pressure

  • LWTEMP

Low temperature

  • LWWTR

Low water

  • MISC

Miscellaneous

  • OPENDR

Open door

  • POWER

Commercial power failure

  • PUMP

Pump failure

  • PWR-48

48 V power supply failure

  • PWR-139

–139 V power converter

  • PWR-190

–190 V power converter

  • PWRMJ

Power supply major

  • PWRMN

Power supply minor

  • RECT

Rectifier failure

  • RECTHI

Rectifier high voltage

  • RECTLO

Rectifier low voltage

  • RINGGENMJ

Ringing generator major

  • RINGGENMN

Ringing generator minor

  • RTACADSL

AC or AC/rectifier power fail ADSL equipment

  • RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

  • RTACPWR

AC or AC/rectifier power fail DCL equipment

  • RTACPWRENG

Commercial AC fail, site equipped with standby engine

  • RTBAYPWR

AC power loss distributed power RT bay

  • RTRVENG

Retrieve standby engine, commercial AC restored

  • SMOKE

Smoke

  • TEMP

High-low temperature

  • TOXICGAS

Toxic gas

  • TREPEATER

T-repeater shelf

  • VENTN

Ventilation system failure

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>],
[<DESC>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“ENV-IN-1:MJ,OPENDR,01-01,16-02-15,,,,\“OPEN DOOR\””
;

 

Table 21-47 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “ENV” section

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<ALMTYPE>

The alarm type for the environmental alarm. The parameter type is ENV_ALM, which is the environmental alarm type.

  • AIRCOMPR

Air compressor failure

  • AIRCOND

Air conditioning failure

  • AIRDRYR

Air dryer failure

  • BATDSCHRG

Battery discharging

  • BATTERY

Battery failure

  • CLFAN

Cooling fan failure

  • CPMAJOR

Centralized power major failure

  • CPMINOR

Centralized power minor failure

  • ENGINE

Engine failure

  • ENGOPRG

Engine operating

  • ENGTRANS

Standby engine transfer

  • EXPLGS

Explosive gas

  • FIRDETR

Fire detector failure

  • FIRE

Fire

  • FLOOD

Flood

  • FUELLEAK

Fuel leak

  • FUSE

Fuse failure

  • GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

  • HATCH

CEV hatch fail

  • GEN

Generator failure

  • HIAIR

High air flow

  • HIHUM

High humidity

  • HITEMP

High temperature

  • HIWTR

High water

  • INTRUDER

Intrusion

  • LEVELCON

Level converter

  • LVDADSL

Secondary ADSL low voltage disconnect

  • LVDBYPAS

Low voltage disconnect bypass

  • LWBATVG

Low battery voltage

  • LWFUEL

Low fuel

  • LWHUM

Low humidity

  • LWPRES

Low cable pressure

  • LWTEMP

Low temperature

  • LWWTR

Low water

  • MISC

Miscellaneous

  • OPENDR

Open door

  • POWER

Commercial power failure

  • PUMP

Pump failure

  • PWR-48

48 V power supply failure

  • PWR-139

–139 V power converter

  • PWR-190

–190 V power converter

  • PWRMJ

Power supply major

  • PWRMN

Power supply minor

  • RECT

Rectifier failure

  • RECTHI

Rectifier high voltage

  • RECTLO

Rectifier low voltage

  • RINGGENMJ

Ringing generator major

  • RINGGENMN

Ringing generator minor

  • RTACADSL

AC or AC/rectifier power fail ADSL equipment

  • RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

  • RTACPWR

AC or AC/rectifier power fail DCL equipment

  • RTACPWRENG

Commercial AC fail, site equipped with standby engine

  • RTBAYPWR

AC power loss distributed power RT bay

  • RTRVENG

Retrieve standby engine, commercial AC restored

  • SMOKE

Smoke

  • TEMP

High-low temperature

  • TOXICGAS

Toxic gas

  • TREPEATER

T-repeater shelf

  • VENTN

Ventilation system failure

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.

21.35 RTRV-COND-EQPT

(Cisco ONS 15454 SDH) The Retrieve Condition Equipment (RTRV-COND-EQPT) command retrieves the equipment conditions.

 
Usage Guidelines

None

Category

Equipment

Security

Retrieve

Input Format

RTRV-COND-EQPT:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

RTRV-COND-EQPT:TID:SLOT-1:229::LOS;

 

Table 21-48 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “EQPT” section of the entity for the entity that has an alarm condition.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],[<OCRTM>],
[<LOCN>],[<DIRN>],[<DESC>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SLOT-1,EQPT:CR,LOS,SA,01-01,16-02-15,NEND,RCV,\"LOS OF SIGNAL\"”
;

 

Table 21-49 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “EQPT” section for the entity that has an alarm condition.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

BITS alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 alarm

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 alarm

  • E3

(ONS 15310 MA SDH) E3 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 alarm

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet port alarm

  • G1000

G1000 alarm

  • GIGE

Gigabit Ethernet port alarm

  • HDLC

High-level data link control (HDLC) frame mode.

  • ML-100T-8

ML-Series 100T eight port Gigabit Ethernet Card

  • CE-100T-8

CE-Series 100T eight port Gigabit Ethernet Card

  • CE-MR-6

CE-Series MR six port Gigabit Ethernet Card

  • CTX-2500

CTX card

  • E1-21-DS3-E3-3,

21 channel WEB card

  • E1-63-DS3-E3-3,

63 channel WEB card

  • FILLER-CARD

Filler Card

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gbps ISC3 Peer

  • ISC3PEER2G

2-Gbps ISC3 Peer

  • ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port alarm

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 alarm

  • STM1E

STM1E alarm

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • SYNCN

SYNCN alarm

  • TCC

TCC alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC44C

VC44C alarm

  • VC38C

VC38C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<TYPEREP>

The type of condition to be retrieved. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRECTION>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.

21.36 RTRV-COND-SYNCN

(Cisco ONS 15454 SDH) The Retrieve Condition Synchronization (RTRV-COND-SYNCN) command retrieves the synchronization condition.

 
Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-COND-SYNCN:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

RTRV-COND-SYNCN:TID:SYNC-NE:229::LOS;

 

Table 21-50 Input Parameter Support

Parameter
Description

<AID>

Access identifier from the “SYNC_REF” section for the entity that has an alarm condition.

<TYPEREQ>

The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>],[<DESC>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SYNC-NE,SYNCN:MJ,FRNGSYNC,SA,01-01,16-02-15,,,
\“FREE RUNNING SYNCHRONIZATION MODE\””
;

 

Table 21-51 Output Parameter Support

Parameter
Description

<AID>

Access identifier from the “SYN” section for the entity that has an alarm condition.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The value is always SYNCN. The parameter type is MOD2B, which is the alarm type.

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • 40GIGE

40-Gigabit Ethernet

  • 5GIB

5Gbps InfiniBand (IB_5G) payload

  • 8GFC

8-Gigabit Fibre Channel payload

  • BITS

BITS alarm

  • CHGRP

Channel group

  • CLNT

Client facility for MXP/TXP cards

  • COM

Common alarm

  • DS3I

DS3i-N-12 alarm

  • DVBASI

Digital Video Broadband Asynchronous Serial Interface (DVBASI) payload

  • E1

E1 alarm

  • E3

(ONS 15310 MA SDH) E3 alarm

  • E100

E100 alarm

  • E1000

E1000 alarm

  • E3

E3 alarm

  • E4

E4 alarm

  • ENV

ENV alarm

  • EQPT

EQPT alarm

  • FSTE

Fast Ethernet port alarm

  • ML-100T-8

ML-Series 100T eight port Gigabit Ethernet Card

  • CE-100T-8

CE-Series 100T eight port Gigabit Ethernet Card

  • CE-MR-6

CE-Series MR six port Gigabit Ethernet Card

  • CTX-2500

CTX card

  • E1-21-DS3-E3-3,

21 channel WEB card

  • E1-63-DS3-E3-3,

63 channel WEB card

  • FILLER-CARD

Filler Card

  • G1000

G1000 alarm

  • GIGE

Gigabit Ethernet port alarm

  • HDLC

High-level data link control (HDLC) frame mode.

  • ISC1

InterSystem Channel, a protocol defined by IBM (ISC1) payload

  • ISC3PEER1G

1-Gbps ISC3 Peer

  • ISC3PEER2G

2-Gbps ISC3 Peer

  • ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G

ISC-3 STP 2G video payload.

  • ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

  • MSISC

MSISC

  • OCH

Optical channel

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • OTU1

Optical Transport Unit Level 1

  • OTU3

Optical Transport Unit Level 3

  • POS

POS port alarm

  • REP

Resilient Ethernet Protocol

  • STM1

STM1 alarm

  • STM1E

STM1E alarm

  • STM4

STM4 alarm

  • STM16

STM16 alarm

  • STM64

STM64 alarm

  • SYNCN

SYNCN alarm

  • TCC

TCC alarm

  • VC11

VC11 alarm

  • VC12

VC12 alarm

  • VC3

VC3 alarm

  • VC44C

VC44C alarm

  • VC38C

VC38C alarm

  • VC464C

VC464C alarm

  • VC48C

VC48C alarm

  • VC4

VC4 alarm

  • VC416C

VC416C alarm

  • VC42C

VC42C alarm

  • VC43C

VC43C alarm

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

  • CL

The condition causing the alarm has cleared.

  • CR

A critical alarm.

  • MJ

A major alarm.

  • MN

A minor alarm.

  • NA

The condition is not alarmed.

  • NR

The alarm is not reported.

<TYPEREP>

The type of condition to be retrieved. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

  • NSA

The condition is non-service affecting.

  • SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the far end of the facility.

  • NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

  • BTH

Both transmit and receive directions

  • RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.

21.37 RTRV-CONSOLE-PORT

(Cisco ONS 15454 SDH) The Retrieve Console Port (RTRV-CONSOLE-PORT) command retrieves the status of the console port from the ML-Series cards.

 
Usage Guidelines

None

Category

Security

Security

Retrieve

Input Format

RTRV-CONSOLE-PORT:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-CONSOLE-PORT:CISCONODE:SLOT-2:123;

Input Parameters

<AID>

Access identifier from the “EQPT” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<EQPT>:PORT=<PORT>”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“SLOT-2:PORT=ENABLED”
;

 

Table 21-52 Output Parameter Support

Parameter
Description

EQPT

Identifies the slot number for the data card. EQPT is a string.

PORT

(Optional) Status of the console port on the data card. The parameter type is PORTSTAT, which is the status of the console port on the card.

  • DISABLED

The port is disabled.

  • ENABLED

The port is enabled.

21.38 RTRV-COS-ETH

(Cisco ONS 15454 SDH) The Retrieve Cost of Service Ethernet (RTRV-COS-ETH) command retrieves the egress parameters of a CoS table associated to an L2 Ethernet port.

 
Usage Guidelines

None

Category

Ethernet

Security

Provisioning

Input Format

RTRV-COS-ETH:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-COS-ETH:TID:ETH-1-1-1:CTAG;

Input Parameters

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the “LINEWL” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<AID>::[QOSENABLED=<QOSENABLED>],[BW0=<BWO>],
[WEIGHT0=<WEIGHT0>],[BW1=<BW1>],[WEIGHT1=<WEIGHT1>],[BW2=<BW2>],
[WEIGHT2=<WEIGHT2>],[BW3=<BW3>],[WEIGHT3=<WEIGHT3>],[BW4=<BW4>],
[WEIGHT4=<WEIGHT4>],[BW5=<BW5>],[WEIGHT5=<WEIGHT5>],[BW6=<BW6>],
[WEIGHT6=<WEIGHT6>],[BW7=<BW7>],[WEIGHT7=<WEIGHT7>][:]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“ETH-5-1-1::QOSENABLED=Y,BW0=10,WEIGHT0=0,BW1=20,WEIGHT1=2,BW2=40,
WEIGHT2=4,BW3=60,WEIGHT3=6,BW4=70,WEIGHT4=8,BW5=80,WEIGHT5=10,BW6=85,
WEIGHT6=12,BW7=100,WEIGHT7=15:”
;

 

Table 21-53 Output Parameter Support

Parameter
Description

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the “ETH” section.

<QOSENABLED>

Used to enable or disable the egress quality of service (QoS) policy of an L2 Ethernet port.

  • N

Disable the service.

  • Y

Enable the service.

<BW0>

Bandwidth percentage, a value between 0 and 100

<WEIGHT0>

Value represents the weighted round-robin (WRR) weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW1>

Bandwidth percentage, a value between 0 and 100

<WEIGHT1>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW2>

Bandwidth percentage, a value between 0 and 100

<WEIGHT2>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW3>

Bandwidth percentage, a value between 0 and 100

<WEIGHT3>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW4>

Bandwidth percentage, a value between 0 and 100

<WEIGHT4>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW5>

Bandwidth percentage, a value between 0 and 100

<WEIGHT5>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW6>

Bandwidth percentage, a value between 0 and 100

<WEIGHT6>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

<BW7>

Bandwidth percentage, a value between 0 and 100

<WEIGHT7>

Value represents the WRR weight associated to the CoS values. It is an integer value ranging between 0 and 15.

21.39 RTRV-CRS

(Cisco ONS 15454 SDH) The Retrieve Cross-Connect (RTRV-CRS) command retrieves all the cross-connections based on the required PATH types.

 
Usage Guidelines

  • A NULL AID defaults to ALL (NE).
  • A NULL PATH defaults to all the existing cross-connections.
  • The LEVEL in the output field is an optional field, and is used to indicate the bandwidth of the PATH cross-connection.
  • Both DRITYPE and DRINODE optional fields are available to support MSSPR-DRI. DRITYPE is applied only if the cross-connect is a drop-and-continue connection (1WAYDC or 2WAYDC), and defaults to SNCP for the DRI. DRINODE must be specified only if at least one end of the connection is on the MS-SPRing, and defaults to NA.
  • CKTID is a string of ASCII characters. The maximum length of CKTID is 48. If the CKTID is EMPTY or NULL it will not appear.
  • VC values in CRS_TYPE are not supported in this command.

Category

Cross Connections

Security

Retrieve

Input Format

RTRV-CRS:[<TID>]:[<AID>]:<CTAG>[:::CRSTYPE=<CRSTYPE>][:];

Input Example

RTRV-CRS:CISCO:ALL:123:::CRSTYPE=VC4;

 

Table 21-54 Input Parameter Support

Parameter
Description

<AID>

(Optional) Access identifier from the “CrossConnectId” section that can be EQPT, Facility, VC or ALL. The ALL AID defaults to NE, which means it reports all the existing cross-connections on the NE. A null value is equivalent to ALL.

<CRSTYPE>

(Optional) The cross-connection type. Defaults to all existing cross-connections. A null value is equivalent to ALL. The parameter type is PATH, which is the modifier for path commands.

  • VC3

Synchronous Transport Signal/Module Level-1 (51 Mbps)

  • VC44C

Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps)

  • VC38C

Synchronous Transport Signal/Module Level-18 Concatenated (933 Mbps)

  • VC464C

Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps)

  • VC48C

Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps)

  • VC4

Synchronous Transport Signal/Module Signal Level-3 Concatenated (155 Mbps)

  • VC416C

Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps)

  • VC42C

Synchronous Transport Signal/Module level-6 (310 Mbps)

  • VC43C

Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps)

  • VC12

Virtual Tributary 2. Virtual Channel 12

Output Format

SID DATE TIME
M CTAG COMPLD
“<SRC>,<DST>:<CCT>,<CRSTYPE>:[DRITYPE=<DRITYPE>],[DRINODE=<SYNCSW>],
[CKTID=<CKTID>]:<PSTPSTQ>,[<SSTQ>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“VC4-5-1-2&VC4-6-1-2,VC4-12-1-2&VC4-13-1-2:1WAYDC,VC3:DRITYPE=MSSPR,
DRINODE=PRI,CKTID=CKTID:UNLOCKED-DISABLED,AUTOMATICINSERVICE”
;

 

Table 21-55 Output Parameter Support

Parameter
Description

<SRC>

Source access identifier from the “CrossConnectId” section. Indicates the source AID(s) of the cross-connection. SRC is listable.

<DST>

Destination AID of the cross-connection from the “CrossConnectId” section. DST is listable.

<CCT>

Type of connection. Used for specifying one or two-way connections. The parameter type is CCT, which is the type of cross-connect to be created.

  • 1WAY

A unidirectional connection from a source tributary to a destination tributary.

  • 1WAYDC

Subnetwork connection protection (SNCP) multicast drop (1-way continue)

  • 1WAYEN

SNCP multicast end node (1-way continue)

  • 1WAYMON

A bidirectional connection between the two tributaries

Note 1WAYMON is not supported with TL1. However, it is supported from CTC. Using CTC, you can create 1WAYMON cross-connects that can be retrieved through TL1.

  • 1WAYPCA

A unidirectional connection from a source tributary to a destination tributary on the protection path/fiber

  • 2WAY

A bidirectional connection between the two tributaries.

  • 2WAYDC

A bidirectional drop and continue connection applicable only to SNCP traditional and integrated DRIs.

  • 2WAYPCA

A bidirectional connection between the two tributaries on the extra protection path/fiber.

  • DIAG

Diagnostics cross-connect. Supports BERT (MS-SPRing PCA diagnostics cross-connect).

<CRSTYPE>

The cross-connection type. The parameter type is CRS_TYPE, which is the cross-connection type.

  • VC

Indicates all the VC cross-connections.

  • VC3

VC3 cross-connect

  • VC4

VC4 cross-connect

  • VC42C

VC42C cross-connect

  • VC43C

VC43C cross-connect

  • VC44C

VC44C cross-connect

  • VC 46C

VC46C cross-connect

  • VC48C

VC48C cross-connect

  • VC412C

VC412C cross-connect

  • VC416C

VC416C cross-connect

  • VC464C

VC464C cross-connect

  • VC12

VC12 cross-connect

<DRITYPE>

(Optional) The DRI connection type. It is applied only if the cross-connection is a drop-and-continue connection type (1WAYDC or 2WAYDC), and defaults to SNCP for the DRI configuration. The parameter type is DRITYPE (DRI type).

  • MSSPR

MS-SPRing DRI type

  • SNCP

SNCP DRI type

  • SNCP-MSSPR

SNCP-MS-SPRing hand off DRI type

<DRINODE>

(Optional) Synchronization switch AID from the “SYNCSW” section.

<CKTID>

(Optional) Circuit identification parameter that contains the a common language ID or other alias of the circuit being provisioned. It cannot contain blank spaces. CKTID is a string.

<PSTPSTQ>

Primary state and primary state qualifier separated by a colon. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked-Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SSTQ>

(Optional) One or more secondary states separated by &, in alphabetical order. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.40 RTRV-CRS-<PATH>

(Cisco ONS 15454 SDH) The Retrieve Cross-Connect for VC3, VC44C, VC38C, VC464C, VC48C, VC4-12C, VC4, VC416C, VC42C, VC43C, VC11, or VC1 (RTRV-CRS-<PATH>) command retrieves any connections associated with the entered AID(s) or AID range. The information on both ends is returned along with the type of connection. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

The SNCP VC cross-connection can be retrieved by using “&” in the AID fields of this command.

  • To retrieve a 1-way selector or 2-way selector and bridge cross-connection with:

from points: F1, F2

to points: T1

the output will be:

1-way:

“F1&F2,T1:CCT,VC4”

2-way:

If retrieved on point F1 or F2, the output format is the same as the 1-way output.

If retrieved on point T1, the output will be:

“T1,F1&F2:CCT,VC4”

  • To retrieve a 1-way bridge or 2-way selector and bridge cross-connection with:

from point: F1

to points: T1, T2

the output will be:

1-way:

“F1,T1&T2:CCT,VC4”

2-way:

“T1&T2,F1:CCT,VC4”

  • To retrieve a 1-way subtending SNCP connection or 2-way subtending SNCP cross-connection with:

from point: F1, F2

to points: T1, T2

the output will be:

1-way:

“F1&F2,T1&T2:CCT,VC4”

2-way:

If retrieved on point F1 or F2, the output format is the same as the 1-way output.

If retrieved on point T1 or T2, the output will be:

“T1&T2,F1&F2:CCT,VC4”

  • To retrieve a 2-way selector and bridge cross-connection with:

ENT-CRS-<PATH>::F1&F2,S1&S2:<CTAG>::2WAY;

from points: F1, F2 (F1 is the working side, F2 is the protect side)

selector: S1, S2 (s1 is the working side, S2 is the protect side)

If retrieved on point F1 or F2, the output will be:

“F1&F2,S1&S2:CCT,VC4”

If retrieved on selector S1 or S2, the output will be:

“S1&S2,F1&F2:CCT,VC4”

  • To retrieve a SNCP IDRI cross-connect with:

from points: F1, F2

to points: T1, T2

the output will be:

“F1&F2,T1&T2:CCT,VC4”

  • To retrieve a SNCP DRI cross-connect with:

from points: F1, F2

to points: T1

the output will be:

“F1&F2,T1:CCT,VC4”

The following rules apply:

  • All A&B AIDs in the TL1 cross-connection command are in the format of WorkingAID&ProtectAID.
  • <VC_PATH> does not include VC for the RTRV-CRS command because VC is not a standard designator as defined by Telcordia GR-833, Section A-2.
  • Both the 1WAYPCA and 2WAYPCA is used to specify a PCA cross-connection.
  • The facility AID is only valid on slots with a G1000-4 card.
  • The virtual facility AID (VFAC) is only valid on slots holding the ML-Series card.
  • Both DRITYPE and DRINODE optional fields are available to support MSSPR-DRI. DRITYPE is applied only if the cross-connect is a drop-and-continue connection (1WAYDC or 2WAYDC), and defaults to SNCP for the DRI. DRINODE must be specified only if at least one end of the connection is on the MS-SPRing, and defaults to NA.
  • Only RTRV-CRS-VC3 will be allowed on the DS3i-N-12 card. RTRV-CRS-VC4 is not allowed.

Category

Cross Connections

Security

Retrieve

Input Format

RTRV-CRS-<PATH>:[<TID>]:<SRC>:<CTAG>[::::];

Input Example

RTRV-CRS-VC4:KENWOOD:VC4-6-1-1:223;

Input Parameters

<SRC>

Source access identifier from the “CrossConnectId1” section.

Output Format

SID DATE TIME
M CTAG COMPLD
“<SRC>,<DST>:<CCT>,<MOD>:[DRITYPE=<DRITYPE>],[DRINODE=<DRINODE>],
[CKTID=<CKTID>]:<PSTPSTQ>,[<SSTQ>]”
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
“VC4-5-1-2&VC4-6-1-2,VC4-12-1-2&VC4-13-1-2:1WAYDC,VC4:DRITYPE=MSSPR,
DRINODE=PRI,CKTID=CKTID:UNLOCKED-DISABLED,AUTOMATICINSERVICE”
;

 

Table 21-56 Output Parameter Support

Parameter
Description

<SRC>

Source access identifier from the “CrossConnectId” section. Indicates the source AID(s) of the cross-connection. SRC is listable.

<DST>

Destination AID of the cross-connection from the “CrossConnectId” section. DST is listable.

<CCT>

Type of connection. Used for specifying one or two-way connections. The parameter type is CCT, which is the type of cross-connect to be created.

  • 1WAY

A unidirectional connection from a source tributary to a destination tributary.

  • 1WAYDC

SNCP multicast drop (1-way continue)

  • 1WAYEN

SNCP multicast end node (1-way continue)

  • 1WAYMON

A bidirectional connection between the two tributaries

Note 1WAYMON is not supported with TL1. However, it is supported from CTC. Using CTC, you can create 1WAYMON cross-connects that can be retrieved through TL1.

  • 1WAYPCA

A unidirectional connection from a source tributary to a destination tributary on the protection path/fiber.

  • 2WAY

A bidirectional connection between the two tributaries.

  • 2WAYDC

A bidirectional drop and continue connection applicable only to SNCP traditional and integrated DRIs.

  • 2WAYPCA

A bidirectional connection between the two tributaries on the extra protection path/fiber.

  • DIAG

Diagnostics cross-connect. Supports BERT (MS-SPRing PCA diagnostics cross-connect).

<MOD>

The connection path bandwidth. The parameter type is MOD2, which is the line/path modifier.

  • 10GFC

10-Gigabit Fibre Channel payload

  • 10GIGE

10-Gigabit Ethernet

  • 1GFC

1-Gigabit Fibre Channel payload

  • 1GFICON

1-Gigabit fiber connectivity payload

  • 2GFC

2-Gigabit Fibre Channel payload

  • 2GFICON

2-Gigabit fiber connectivity payload

  • 3GVIDEO

3G-SDI video payload.

  • 4GFC

4-Gigabit Fibre Channel payload

  • 4GFICON

4-Gigabit fiber connectivity payload

  • D1VIDEO

D1 video

  • DS3I

DS3i-N-12 line

  • DV6000

DV6000

  • E1

E1

  • E3

E3

  • E4

E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.

  • ESCON

ESCON

  • ETRCLO

ETRCLO

  • FSTE

FSTE facility

  • G1000

G1000 facility

  • GFPOS

Generic Framing Protocol over Packet Over SDH. Virtual ports partitioned using GFP's multiplexing capability

  • GIGE

Gigabit Ethernet

  • HDTV

HDTV

  • ISC3PEER1G

1-Gbps ISC3 Peer

  • ISC3PEER2G

2-Gbps ISC3 Peer

  • ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

  • ISC3STP1G

ISC-3 STP 1G video payload.

  • ISC3STP2G
  • ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

  • STM1

STM1 facility

  • STM4

STM4 facility

  • STM16

STM16 facility

  • STM64

STM64 facility

  • OCH

Optical channel

  • OCHCC

OCH client connection

  • OCHNC

OCH network connection

  • OCHTERM

OCH termination

  • OMS

Optical Multiplex Section

  • OTS

Optical Transport Section

  • POS

POS port

  • STM1E

STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.

  • VC3

VC3 path

  • VC4

VC4 path

  • VC42C

VC42C path

  • VC43C

VC43C path

  • VC44C

VC44C path

  • VC 46C

VC46C path

  • VC48C

VC48C path

  • VC412C

VC412C path

  • VC416C

VC416C path

  • VC464C

VC464C path

  • VC11

VC11 path

  • VC12

VC12 path

<DRITYPE>

(Optional) The DRI connection type. It is applied only if the cross-connection is a drop-and-continue connection type (1WAYDC or 2WAYDC), and defaults to SNCP for the DRI configuration. The parameter type is DRITYPE (DRI type).

  • MSSPR

MS-SPRing DRI type

  • SNCP

SNCP DRI type

  • SNCP-MSSPR

SNCP-MS-SPRing hand off DRI type

<SYNCSW>

(Optional) Synchronization switch AID from the “SYNCSW” section.

<CKTID>

(Optional) A string of ASCII characters. Maximum length is 48. CKTID is a string.

<PSTPSTQ>

Primary state and primary state qualifier separated by a colon. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

  • Unlocked-Enabled

In service and normal

  • Unlocked-Disabled

Out of service and autonomous

  • Locked-Disabled

Out of service, autonomous and management

  • Locked-Enabled

Out of service and management

<SSTQ>

(Optional) One or more secondary states separated by &, in alphabetical order. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

  • AutomaticInService

Automatic in service

  • Disabled

Disabled

  • Loopback

Loopback

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

  • Maintenance

Maintenance mode

  • OutOfGroup

Out of group

  • SoftwareDownload

Software downloading

  • Unassigned

Unassigned

  • NotInstalled

Unequipped

21.41 RTRV-CRS-ETH

(Cisco ONS 15454 SDH)

This command retrieve an Ethernet Connection between two or more ethernet connection end points within ethernet facilities.

 
Usage Guidelines

This command accept the AL