Cisco ONS SDH TL1 Command Guide, Release 9.4
Chapter 15, INIT Commands
Downloads: This chapterpdf (PDF - 372.0KB) The complete bookPDF (PDF - 10.93MB) | Feedback

Table of Contents

INIT Commands

INIT Commands

This chapter provides initialize (INIT) commands for the Cisco ONS 15454 SDH, and Cisco ONS 15454 M2, Cisco ONS 15454 M6.


Note All commands supported on the Cisco ONS 15454 SDH platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.


15.1 INIT-REG-<MOD2>

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Initialize Register for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 5GIB, 8GFC, CHGRP, CLNT, D1VIDEO, DS3I, DV6000, DVBASI, E1, E3, E4, ESCON, ETH, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDLC, HDTV, ISC1, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OTU3, STM4, STM64, STM1, STM16, OCH, OMS, OTS, POS, STM1E, T3, VC3, VC44C, VC38C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC12, 3GVIDEO, SDSDI , HDSDI, AUTO, OTU1, ISC3STP1G, or ISC3STP2G (INIT-REG-<MOD2>) command initializes the performance monitoring (PM) registers.

 
Usage Guidelines

The command supports the modifier 3GVIDEO, SDSDI , HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G.

See Table 27-1 for supported modifiers by platform.

  • The time period is always the current time period, and the previous time period counts are not cleared; therefore, both <MONDAT> and <MONTM> are not supported in this command.
  • All cards support only the receive (RCV) direction. BTH is not supported for this command.
  • INIT-REG-<MOD2> can also be used to initialize the remote monitoring (RMON) managed raw data.

Category

Performance

Security

Provisioning

Input Format

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LOCN>],[<DIRN>],[<TMPER>]
[,,];

Input Example

Cisco ONS 15454 SDH

INIT-REG-OTU1:CISCO:VFAC-1-2-1:1234::CVL,,NEND,BTH,15-MIN;

 

Table 15-1 Parameter Support

Parameter
Description

<AID>

Access identifier from the “ALL” section. All of the STS, VT1, Facility, and DS1 AIDs are supported. The AR-MXP and AR-XP cards use the VFAC AID.

<MONTYPE>

Monitored type. The parameter type is ALL_MONTYPE, which is the monitoring type list.

  • AISSP

Alarm Indication Signal Seconds Path

  • ALL

All possible values

  • BBEP

SDH Background Block Errors Path

  • BBE-PM

OTN—Background Block Errors—Path Monitor Point

  • BBER

SDH Background Block Error Ratio

  • BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as one tenth of a percentage.

  • BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as one tenth of a percentage.

  • BBE-SM

OTN—Background Block Errors—Section Monitor Point

  • BIEC

FEC—Bit Errors Corrected

  • BIT-EC

The number of bit errors corrected by the FEC algorithm

  • CGV

8B10B—Code Group Violations

  • CVCPP

Coding Violations—CP-Bit Path

  • CVL

Coding Violations—Line

  • CVP

Coding Violations—Path

  • CVS

Coding Violations—Section

  • CVV

Coding Violations—Section

  • DCG

8B10B—Data Code Groups

  • ESCPP

Errored Seconds—CP Bit Path

  • ESL

Errored Seconds—Line

  • ESP

Errored Seconds—Path

  • ES-PM

OTN—Errored Seconds—Path Monitor Point

  • ESR

Errored Second—Ratio

  • ESR-PM

Errored Seconds Ratio—Path monitor Point expressed as tenths of a percentage

  • ESR-SM

Errored Seconds Ratio—Section monitor Point expressed as tenths of a percentage

  • ESS

Errored Seconds—Section

  • ES-SM

OTN—Errored Seconds—Section Monitor Point

  • ESV

Errored Seconds—VC Path

  • etherStatsBroadcastPkts

The total number of good packets received that were directed to a multicast address

  • etherStatsCollisions

Number of transmit packets that are collisions

  • etherStatsCRCAlignErrors

The total number of packets received that have a length (excluding framing bits, but including frame check sequence [FCS] octets) of between 64 and 1518 octets

  • etherStatsDropEvents

Number of received frames dropped at the port level

  • etherStatsFragments

The total number of packets received that were less than 64 octets

  • etherStatsJabbers

The total number of packets received that are longer than 1518 octets

  • etherStatsOctets

The total number of octets of data

  • etherStatsOversizePkts

The total number of packets received that are longer than 1518 octets

  • etherStatsPkts

The total number of packets (including bad packets, broadcast packets, and multicast packets) received

  • etherStatsUndersizePkts

The total number of packets received that are less than 64 octets

  • FCP

Failure Count—Line

  • FC-PM

OTN—Failure Count—Path Monitor Point

  • FC-SM

OTN—Failure Count—Section Monitor Point

  • HP-AR

Availability Ratio

  • HP-BBE

High-Order Path Background Block Error

  • HP-BBER

High-Order Path Background Block Error Ratio

  • HP-EB

High-Order Path Errored Block

  • HP-ES

High-Order Path Errored Second

  • HP-ESA

High-Order Path Errored Seconds–A

  • HP-ESB

High-Order Path Errored Seconds–B

  • HP-ESR

High-Order Path Errored Second Ratio

  • HP-FC

High-Order Path Failure Count

  • HP-NPJC-PDET

High Order Path Negative Pointer Justification Count

  • HP-NPJC-PGEN

High Order Path Pointer Justification Count Seconds

  • HP-OI

Outage Intensity

  • HP-PJCDIFF

High Order Path Pointer Justification Count Difference

  • HP-PJCS-PDET

High Order Path Pointer Justification Count

  • HP-PPJC-PDET

High Order Path Positive Pointer Justification Count

  • HP-PPJC-PGEN

High Order Path, Positive Pointer Justification Count

  • HP-SEPI

The number of Severely Errored Period Intensity events in available time

  • HP-SES

High-Order Path Severely Errored Seconds

  • HP-SESR

High-Order Path Severely Errored Second Ratio

  • HP-UAS

High-Order Path Unavailable Seconds

  • ifInBroadcastPkts

Number of broadcast packets received since the last counter reset

  • ifInDiscards

The number of inbound packets

  • ifInErrorBytePktss

Receive Error Byte

  • ifInErrors

The number of inbound packets (or transmission units) that contained errors

  • ifInFramingErrorPkts

Receive Framing Error

  • ifInJunkInterPkts

Receive Interpacket Junk

  • ifInMulticastPkts

Number of multicast packets received since the last counter reset

  • ifInOctets

Number of bytes transmitted since the last counter reset

  • ifInUcastPkts

Number of unicast packets received since the last counter reset

  • ifOutBroadcastPkts

Number of broadcast packets transmitted

  • ifOutDiscards

The number of outbound packets

  • ifOutErrors

The number of outbound packets (or transmission units) that could not be transmitted because of errors

  • ifOutMulticastPkts

Number of multicast packets transmitted

  • ifOutPayloadCrcErrors

Received payload cyclic redundancy check (CRC) errors

  • ifOutUcastPkts

Number of unicast packets transmitted

  • IOS

8B10B–Idle Ordered Sets

  • IPC

Invalid Packet Count

  • LBCL-AVG

Average Laser Bias current in micro A

  • LBCL-MAX

Maximum Laser Bias current in micro A

  • LBCL-MIN

Minimum Laser Bias current in micro A

  • LBCN

Normalized Laser Bias Current for STM1-8

  • LBCN-HWT

Laser Bias current

  • LBCN-LWT

Laser Bias current

  • LOSSL

Loss of Signal Seconds—Line

  • LP-BBE

Low-Order Path Background Block Error

  • LP-BBER

Low-Order Path Background Block Error Ratio

  • LP-EB

Low-Order Path Errored Block

  • LP-ES

Low-Order Path Errored Second

  • LP-ESA

Low-Order Path Errored Seconds–A

  • LP-ESB

Low-Order Path Errored Seconds–B

  • LP-ESR

Low-Order Path Errored Second Ratio

  • LP-FC

Low-Order Path Failure Count

  • LP-NPJC-DET

Low Order Negative Pointer Justification Count, Detected

  • LP-NPJC-GEN

Low Order Negative Pointer Justification Count, Generated

  • LP-PPJC-DET

Low Order Positive Pointer Justification Count, Detected

  • LP-PPJC-GEN

Low Order Positive Pointer Justification Count, Generated

  • LP-SEP

A sequence of between 3 to 9 consecutive severely errored seconds (SES)

  • LP-SEPI

Low-Order Path Severely Errored Period Intensity

  • LP-SES

Low-Order Path Severely Errored Seconds

  • LP-UAS

Low-Order Path Unavailable Seconds

  • MS-PSC

Multiplex Section-Protection switch count

  • MS-PSD

Multiplex Section-Protection switch duration

  • NIOS

8B10B—Non Idle Ordered Sets

  • NPJC-PDET

Negative Pointer Justification Count, Path Detected

  • NPJC-PGEN

Negative Pointer Justification Count, Path Generated

  • OPR-AVG

Average Receive Power in tenths of a micro W

  • OPR-MAX

Maximum Receive Power in tenths of a micro W

  • OPR-MIN

Minimum Receive Power in tenths of a micro W

  • OPRN

Normalized Optical Receive Power for STM1-8

  • OPRN-MAX

Maximum value for OPRN

  • OPRN-MIN

Minimum value for OPRN

  • OPT-AVG

Average Transmit Power in tenths of a micro W

  • OPT-MAX

Maximum Transmit Power in tenths of a micro W

  • OPT-MIN

Minimum Transmit Power in tenths of a micro W

  • OPTN

Normalized value for Optical Power Transmitted for STM1-8 card

  • OPTN-MAX

Maximum value for OPTN

  • OPTN-MIN

Minimum value for OPTN

  • OPWR-AVG

Optical Power—Average Interval Value in tenths of a dBm

  • OPWR-MAX

Optical Power—Maximum Interval Value in tenths of a dBm

  • OPWR-MIN

Optical Power—Minimum Interval Value in tenths of a dBm

  • PPJC-PDET

Positive Pointer Justification Count, Path Detected

  • PPJC-PGEN

Positive Pointer Justification Count, Path Generated

  • PSC

Protection Switching Count

  • PSC-R

Protection Switching Count—Ring

  • PSC-S

Protection Switching Count—Span

  • PSC-W

Protection Switching Count—Working

  • PSD

Protection Switching Duration

  • PSD-R

Protection Switching Duration—Ring

  • PSD-S

Protection Switching Duration—Span

  • PSD-W

Protection Switching Duration—Working

  • SASCPP

Severely Errored Framing/AIS Second—CP-Bit Path

  • SASP

Severely Errored Framing/AIS Seconds Path

  • SEFS

Severely Errored Framing Seconds

  • SESCPP

Severely Errored Second—CP-Bit Path

  • SESL

Severely Errored Second—Line

  • SESP

Severely Errored Second—Path

  • SES-PM

OTN—Severely Errored Second—Path

  • SESR

Severely Errored Second—Ratio

  • SESR-PM

OTN—Severely Errored Second Ratio—Path Monitor Point expressed as tenths of a percentage

  • SESR-SM

OTN—Severely Errored Second Ratio—Section Monitor Point expressed as tenths of a percentage

  • SESS

Severely Errored Second—Section

  • SES-SM

OTN—Severely Errored Second—Section Monitor Point

  • SESV

Severely Errored Second—VC Path

  • UASCPP

Unavailable Second—CP-Bit Path

  • UASL

Unavailable Second—Line

  • UASP

Unavailable Second—Path

  • UAS-PM

OTN—Unavailable Second—Path Monitor Point

  • UAS-SM

OTN—Unavailable Second—Section Monitor Point

  • UASV

Unavailable Second—VC Path

  • UNC-WORDS

FEC—Uncorrectable Words

  • VPC

Valid Packet Count

<LOCN>

(Optional) Location associated with a particular command in reference to the entity identified by the AID. The parameter type is LOCATION, which is the location where the action is to take place.

  • FEND

Action occurs on the Far End of the facility.

  • NEND

Action occurs on the Near End of the facility.

<DIRN>

(Optional) Direction relative to the entity identified by the AID. Defaults to ALL, which means that the command initializes all of the registers irrespective of the PM direction. The parameter type is DIRECTION (transmit and receive directions).

  • RCV

Receive direction only

<TMPER>

(Optional) Accumulation time period for performance counters. A null value defaults to 15-MIN. Defaults to 15-MIN. The parameter type is TMPER, which is the accumulation time period for the performance management center.

  • 1-DAY

Performance parameter accumulation interval length; every 24-hours. For SDH PM data only one day of history data is available. For RMON managed PM data seven days of history data are available.

  • 1-HR

Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available.

  • 1-MIN

Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available.

  • 15-MIN

Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length.

  • RAW-DATA

Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs.

15.2 INIT-SYS

(Cisco ONS 15454 SDH) The Initialize System (INIT-SYS) command initializes the specified card and its associated subsystem(s).

 
Usage Guidelines

  • This command cannot be executed if the network is in a M ultiplex-Section Shared Protection Ring (MS-SPRing)
  • The SLOT-ALL AID and the list AID are not allowed in this command.
  • Only one level of reset is supported in this command.
  • It is important that the standby TCC2/TCC2P/TCC3, TNC, TSC, and CTX cards should be up and running fully standby before this command is sent on the active TCC2/TCC2P/TCC3, TNC, TSC, and CTX cards for a period of time. During this time, the system is vulnerable to traffic outages caused by timing disruptions or other causes.
  • Before a card is hard reset, it must be in one of the following state:ADMIN STATE - LOCKED,MAINTENANCE & SERVICE STATE - LOCKED-ENABLED, MAINTENANCE.

Category

System

Security

Maintenance

Input Format

INIT-SYS:[<TID>]:<AID>:<CTAG>::<PH>[,<CMDMDE=CMDMDE>];

Input Example

INIT-SYS:HOTWATER:SLOT-1:201::1,CMDMDE=FRCD;

 

Table 15-2 Parameter Support

Parameter
Description

<AID>

Access identifier from the “EQPT” section.

<PH>

The phase. 1=soft reset; 2=hard reset. PH is an integer.

The PH parameter is supported on the CE-100T-8 and CE-MR-10 cards on the ONS 15454.

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

  • FRCD

Force the system to override a state in which the command would normally be denied.

  • NORM

Execute the command normally. Do not override any conditions that could make the command fail.