Cisco ONS SDH TL1 Command Guide, Release 9.4
Chapter 10, DLT Commands
Downloads: This chapterpdf (PDF - 656.0KB) The complete bookPDF (PDF - 10.93MB) | Feedback

Table of Contents

DLT Commands

DLT Commands

This chapter provides delete (DLT) commands for the Cisco ONS 15454 SDH, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.


Note All commands supported on the Cisco ONS 15454 SDH platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.


10.1 DLT-<MOD1PAYLOAD>

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Delete 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, 5GIB, 8GFC, CHGRP, D1VIDEO, DV6000, DVBASI, ESCON, ETRCLO, FSTE,GIGE, HDTV, ISC1, ISC3PEER1G, ISC3PEER2G, ISC3PEER2R, ISCCOMPAT, OTU3, STM4, STM64, STM1, STM16, STM-256, 3GVIDEO, SDSDI , HDSDI, AUTO, OTU1, ISC3STP1G, or ISC3STP2G (DLT-<MOD1PAYLOAD>) command deletes the specified port.

 
Usage Guidelines

The command supports the 3GVIDEO, SDSDI , HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G modifiers.

See Table 27-1 for other supported modifiers by platform.

The ports must be in out of service (OOS) state and must not have any circuits on them while deleting.


Note This command supports ports with pluggable port modules (PPMs), for example, the ASAP card, the FC_MR-4 card and ONS 15454 dense wavelength division multiplexing (DWDM) cards.


Category

Ports

Security

Provisioning

Input Format

DLT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

Cisco ONS 15454 SDH

DLT-GIGE:PETALUMA:FAC-5-1-1-1:1;

DLT-OTU1: ROCCIANERA:VFAC-1-3-2-1:1;

Input Parameters

<AID>

Access identifier from the “FACILITY” sectionand “CHANNEL” section. The AR-MXP and AR-XP cards use the VFAC AID.

10.2 DLT-<MOD_RING>

(Cisco ONS 15454 SDH) The Delete MS-SPRing (DLT-<MOD_RING>) command deletes the multiplex section-shared protection ring (MS-SPRing) of the network element (NE).

 
Usage Guidelines

The following actions will return error messages:

  • If the system fails on getting the information object repository (IOR), a SROG (Status, Get IOR Failed) an error message is returned.
  • If the AID is invalid, an IIAC (Invalid AID) error message is returned.
  • If the MS-SPRing does not exist, a SRQN (MSSPR Does Not Exist) error message is returned.
  • The SROF (Facility Not Provisioned) or (Cannot Access MSSPR) error message is returned for an invalid query.
  • If the MS-SPRing is in use, a SROF (MSSPR In Use) error message is returned.
  • The SRQN (MSSPR Deletion Failed) error message is returned for an invalid deletion query.

Note The ALL AID is invalid for this command.



Note The list AID format has been supported since Release 4.6.


Category

MS-SPRing

Security

Provisioning

Input Format

DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::];

Input Example

DLT-MSSPR:PETALUMA:MSSPR-2:123;

Input Parameters

<AID>

Access identifier from the “AidUnionId1” section. Identifies the MS-SPRing of the NE. The ALL and MSSPR-ALL AIDs cannot be used when deleting MS-SPRings.

10.3 DLT-ALMTYPE

(Cisco ONS 15454 SDH) The Delete Alarm Type (DLT-ALMTYPE) command deletes only user-defined alarm types.

 
Usage Guidelines

ALMTYPE must not contain blank spaces or special characters other than hyphen (-). The maximum ALMTYPE length allowed is 20 characters.

Only one alarm type can be deleted at a time using this command. There is no option available to delete ALL user-defined alarm types.

Category

System

Security

Provisioning

Input Format

DLT-ALMTYPE:[<TID>]::<CTAG>:: <ALMTYPE>;

Input Example

DLT-ALMTYPE:::1::USERDEFINEDALARM;

Input Parameters

<ALMTYPE>

Specifies user-defined alarm types associated with virtual wires in environmental alarm inputs.

10.4 DLT-AUTO

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Delete Auto (DLT-AUTO) command deletes AUTO ports.

 
Usage Guidelines

The ports must be in OOS state and must not have any circuits on them while deleting.

Category

Ports

Security

Provisioning

Input Format

DLT-AUTO:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-AUTO::VFAC-1-3-2-1:1;

Input Parameters

<AID>

The AR-MXP and AR-XP cards use the VFAC AID.

10.5 DLT-BULKROLL-<STM_TYPE>

(Cisco ONS 15454 SDH) The Delete Bulkroll for STM4, STM64, STM1, or STM16 (DLT-BULKROLL-STM_TYPE) command deletes an attempted bulk rolling operation of a facility or completes an attempted rolling operation. This command is used for bulk line level rolling. Use DLT-ROLL-<MOD_PATH> for single path level rolling. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

DLT-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],WHY=<WHY>;

Input Example

DLT-BULKROLL-STM4:CISCO:FAC-1-1:6:::RFROMSTART=VC4-1-1-1,
RFROMEND=VC4-1-1-11,WHY=STOP;

Table 10-1 DLT-BULKROLL-STM_TYPE Command - Parameter Support

Input Parameters
Description

<FROM>

One of the endpoints. Access identifier from the “FACILITY” section for line level rolling and bulk rolling.

<RFROMSTART>

(Optional) The starting time slot in the source roll port. For bulk rolling only. The AID is from the “CrossConnectId1” section (VC or VC11).

<RFROMEND>

(Optional) The ending time slot in the source roll port. For bulk rolling only. The AID is from the “CrossConnectId1” section (VC or VC11).

<WHY>

The reason for deletion. The parameter type is WHY, which is the reason for deletion.

  • END

Drop the leg to be rolled; this leg is identified by the RFROM parameter in the ENT-ROLL or ENT-BULKROLL command.

  • STOP

The rolling operation will be aborted and reverted to the previous configuration.

10.6 DLT-BWP-ETH

(Cisco ONS 15454 SDH) The Delete Bandwidth Profile Ethernet (DLT-BWP-ETH) command deletes a bandwidth profile from the bandwidth profile database (BWP DB). The BWP DB is a collection of BWP used in a Network Element.

 
Usage Guidelines

Error conditions for deleting bandwidth profile can be:

  • Invalid AID. If the AID is invalid an IIAC (Invalid AID) error message is returned.
  • The “ALL” AID is invalid for this command.

Category

Ethernet

Security

Provisioning

Input Format

DLT-BWP-ETH:[<TID>]:<AID>:<CTAG>[::::];

Input Example

DLT-BWP-ETH:ROCKS:BWP-10000:1;

Input Parameters

Table 10-2 DLT-BWP-ETH Command - Parameter Support

Input Parameters
Description

<AID>

This AID is used to access BWP.

  • BWP-ALL

All AID for BWP.

  • BWP-{1-10000}

Single AID for BWP. The valid identifier ranges from 1 to 10000.

10.7 DLT-CPS

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Delete Control Plane Service (DLT-CPS) command deletes a Control Plane Service parameter.

 
Usage Guidelines

  • Specify only the source port to identify the CPS
  • Specify both the source AIDs, if the CPS is of type ADD 2WAY

Category

DWDM

Security

Provisioning

Input Format

DLT-CPS:[<TID>]:<SRC>:<CTAG>::[:CKTID=<CKTID>][:];

Input Example

DLT-CPS::PCHAN-1-2-RX&PCHAN-1-2-TX:8::;

Input Parameters

<SRC>

Source AID from the “CrossConnectId1” section.

<CKTID>

Circuit identification parameter can be used to filter this command

10.8 DLT-CRS-<PATH>

(Cisco ONS 15454 SDH) The Delete Cross-Connection for VC3, VC44C, VC38C, VC464C, VC48C, VC36C, VC4, VC416C, VC42C, VC43C, or VC12 (DLT-CRS-<PATH>) command deletes a cross-connection between VC paths. VC paths are specified using their VC AID. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

  • The fields after CTAG (including trailing colons) are optional.
  • For the one-way cross-connections, the AIDs must be in the same order as originally entered; for the two-way cross-connections, either order will work.
  • This command does not support deleting multiple VC cross-connections.
  • Using “&” in the AID field of this command can delete a subnetwork connection protection (SNCP) virtual container (VC) cross-connection.

The following command is used to delete a one-way selector or two-way selector and bridge with:

from points: F1, F2

to point: T1

DLT-CRS-{VC_PATH}:[<TID>]:F1&F2,T1:<CTAG>;

The following command is used to delete a one-way bridge or two-way selector and bridge with:

from point: F1

to points: T1, T2

DLT-CRS-{VC_PATH}:[<TID>]:F1,T1&T2:<CTAG>;

The following command is used to delete a one-way or two-way subtending SNCP connection with:

from points: F1, F2

to points: T1, T2

DLT-CRS-{VC_PATH}:[<TID>]:F1&F2,T1&T2:<CTAG>;

The AID format in the deletion command is the same as the AID format in the retrieved response message. For example, if the output of any retrieved AID is “F1&F2,T1:CCT,VC4”, the deletion command with the AID format F1&F2,T1 is required to delete this cross-connection.

The following command is used to delete a SNCP IDRI (integrated dual-ring interconnect) cross-connection:

DLT-CRS-{VC_PATH}:[<TID>]:A&B,C&D:<CTAG>;

A–Path on Ring X to which traffic from Ring Y is bridged

B–Path on Ring X to which traffic from the same ring is bridged

C–Path on Ring Y to which traffic from Ring X is bridged

D–Path on Ring Y to which traffic from the same ring is bridged

A, B, C, and D have a positional meaning. Connection type 2WAYDC is used for SNCP IDRI cross-connections.

The following command is used to delete an SNCP dual-ring interconnect (DRI) cross-connection:

DLT-CRS-{VC_PATH}:[<TID>]:A&B,C:<CTAG>;

A–Path on Ring X to which traffic from Ring Y is bridged

B–Path on Ring X to which traffic from the same ring is bridged

C–Traffic to and from Ring Y

A, B, and C have a positional meaning. Connection type 2WAYDC is used for SNCP DRI cross-connections.

  • All A&B AIDs in the TL1 cross-connection command are in the format of WorkingAID&ProtectAID.
  • You can experience some implementation behavior problems if additional drops have been added to the connection object.
  • The facility AID is only valid for slots holding the G1K-4 card.
  • The virtual facility AID (VFAC) is only valid on slots holding an ML-Series card.
  • CKTID is a string of ASCII characters. The maximum length of CKTID can be 48 characters. If the CKTID is EMPTY or NULL, the field will not appear.
  • The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to retrieve current values.

Category

Cross Connections

Security

Provisioning

Input Format

DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::CKTID=<CKTID>,]
[CMDMDE=<CMDMDE>];

Input Example

DLT-CRS-VC44C:VINBURG:VC4-1-1-1,VC4-12-1-1:102:::CKTID=XYZ,CMDMDE=NORM;

Table 10-3 DLT-CRS-<PATH> Command - Parameter Support

Input Parameters
Description

<SRC>

Source AID from the “CrossConnectId1” section.

<DST>

Destination AID from the “CrossConnectId1” section.

<CKTID>

(Optional) Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48. If CKTID is empty or null, the CKTID field will not be displayed.

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

  • FRCD

Force the system to override a state where the command would normally be denied.

  • NORM

Execute the command normally. Do not override any conditions that might make the command fail.

10.9 DLT-CRS-ETH

(Cisco ONS 15454SDH) The Delete Cross-Connect Ethernet (DLT-CRS-ETH) command deletes a cross connection between the ethernet paths. Ethernet paths are specified by using their ethernet facilities AID and SVLAN.

 
Usage Guidelines

This command deletes an ethernet connection between two or more ethernet connection end points inside an ethernet port. Specify all the ethernet connection end points associated in order to identify a unique cross-connection inside the node.

Category

DWDM

Security

Provisioning

Input Format

DLT-CRS-ETH:[<TID>]:<src>,<dst>:<CTAG>:::[CKTID=<cktid>],[CMDMDE=<cmdmde>];

Input Example

DLT-CRS-ETH:VA454-22:ETHID-1-3-2-1-15,ETH-1-3-21-1-15:116:::CKTID=CIRCUIT,CMDMDE=FRCD;

Input Parameters

Table 10-4 Parameter Support

Parameter
Description

<ALL>

The ALL aid is applicable for RTRV-only commands, basically the RTRV-rr type of commands.

  • ETHID[-{1-12}]-{1-5,12-16}-{1-22}-1-{1-20}

Ethernet connection end point aid for GE-XP card.

  • ETHID[-{1-12}]-{1-6,12-17}-{1-4}-1-{1-20}

Facility aid for 10GE-XP card.

<CKTID>

Circuit identification parameter contains the Common Language Circuit ID or other alias of the circuit being provisioned. Default value is - "NULL"

<CMDMDE>

Command Mode is used to force the system to execute a given irrespective of any standing conditions. Default value is -NORM

  • FRCD

Force the system to override a state in which the command would normally be denied.

  • NORM

Execute the command normally. Do not override any conditions that may make the command fail.

10.10 DLT-EQPT

(Cisco ONS 15454 SDH) The Delete Equipment (DLT-EQPT) command deletes a card from the NE. This command removes the card type and attributes that were entered for a particular slot. If any facilities are assigned, they are also deleted.

The DLT-EQPT command also deletes a shelf that is no longer used. A shelf can only be deleted if there is no equipment present or if the equipment and its attributes are not in use and can be deleted as well. Only one REPT DBCHG on SHELF-{1-8} will be reported in the latter case. The node controller shelf (the shelf whose shelf ID is 1) cannot be deleted.

 
Usage Guidelines

The command will be denied if the card is part of a protection group or has a cross-connect endpoint. To delete a card that is part of a protection group, it has to be removed from the protection group first using the ED-EQPT command.

The error message SPLD (Equipment In Use) will be returned in the following conditions:

  • The card is in a protection group.
  • The card has a cross-connection, a data communications channel (DCC), a generic communications channel (GCC), an optical service channel (OSC), or a provisionable patchcord termination.
  • Any of its facilities are being used as a synchronization source.

Note If a card is not provisioned, an error message is returned.


Category

Equipment

Security

Provisioning

Input Parameters

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::];

Input Example

DLT-EQPT:SONOMA:SLOT-1:104;

Input Parameters

<AID>

Access identifier from the “EQPT” section. Identifies an equipment unit (slot) to act on.

10.11 DLT-FFP-<MOD2DWDMPAYLOAD>

(Cisco ONS 15454 SDH) The Delete Facility Protection Group for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, 8GFC, D1VIDEO, DV6000, DVBASI, ETRCLO, FSTE, GIGE, HDTV, ISC1, ISC3, PASSTHRU, OCH, OTU3, OTU1, ISC3STP1G, or ISC3STP2G (DLT-FFP-<MOD2DWDMPAYLOAD>) command deletes Y-cable protection on client facilities.

 
Usage Guidelines

  • The command does not support 3GVIDEO, SDSDI, HDSDI, and AUTO payloads on AR-MXP and AR-XP cards.
  • The command deletes the facility protection group on that port.

Category

Protection

Security

Provisioning

Input Format

DLT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>,<DST>:<CTAG>[:::];

Input Example

DLT-FFP-HDTV:CISCO:FAC-1-1-1,FAC-2-1-1:100;

DLT-FFP-OTU1:ROCCIANERA:VFAC-2-1-1,VFAC-1-1-1:1;

Input Parameters

Table 10-5 DLT-FFP-<MOD2DWDMPAYLOAD> Command - Parameter Support

Input Parameters
Description

<SRC>

Source AID from the “FACILITY” section. The AR-MXP and AR-XP cards use working facility VFAC AID.

  • CHANNEL

The CHAN aid is used to access Optical Channels (OCH) layer of Optical Network/Client units. Value: CHAN[-{1-30}]-{1-6,12-17}-{1-4}-{1}, which is a Single Channel of an OTU2-XP card.

<DST>

Destination AID from the “FACILITY” section. The AR-MXP and AR-XP cards use protecting facility VFAC AID.

  • CHANNEL

The CHAN aid is used to access Optical Channels (OCH) layer of Optical Network/Client units. Value: CHAN[-{1-30}]-{1-6,12-17}-{1-4}-{1}, which is a Single Channel of an OTU2-XP card.

10.12 DLT-FFP-<STM_TYPE>

(Cisco ONS 15454 SDH) The Delete Facility Protection Group for STM4, STM64, STM1, or STM16 (DLT-FFP-<STM_TYPE>) command deletes an synchronous transfer mode (STM) facility protection group in a 1+1 architecture. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

If the protection group does not exist, an error message will be returned.

Category

Protection

Security

Provisioning

Input Format

DLT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::];

Input Example

DLT-FFP-STM1:PETALUMA:FAC-2-1,FAC-1-1:1;

Input Parameters

<WORK>

The working facility AID from the “FACILITY” section.

<PROTECT>

The protect facility AID from the “FACILITY” section.

10.13 DLT-FOG

(Cisco ONS 15454 SDH) The Delete Fan-Out-Group (DLT-FOG) command deletes the provisioned Fan-out-Group.

 
Usage Guidelines

  • Deletes the provisioned FOG.
  • If AID is invalid, an IIAC (Invalid AID) error message is returned.
  • An error message will be returned if the unprovisioned FOG AID is entered.

Category

Equipment

Security

Provisioning

Input Format

DLT-FOG:[<TID>]:<AID>:<CTAG>[:::];

Input Examples

DLT-FOG::FOG-1-37:1;

Input Parameters

<AID>

Access identifier of the Fan-out-group. The ALL AIDs are not allowed for deleting the FOGs. Access identifier from the “EQPT” section.

10.14 DLT-FTPSERVER

(Cisco ONS 15454 SDH) The Delete FTP Server (DLT-FTPSERVER) command deletes FTP server entries.

 
Usage Guidelines

None

Category

ENE

Security

Superuser

Input Format

DLT-FTPSERVER:[<TID>]::<CTAG>:::IPADDR=<IPADDR>;

Input Examples

1. DLT-FTPSERVER:[<TID>]::<CTAG>:::IPADDR=10.20.30.40;

2. DLT-FTPSERVER:TID::CTAG:::IPADDR=“[3ffe:0501:0008:0000:0260:97ff:fe40:efab]”;

Input Parameters

<IPADDR>

Specifies the IP address of the FTP Server entry to be deleted. IPADDR=ALL specifies that ALL entries are deleted from the list.

10.15 DLT-LMP-CTRL

(Cisco ONS 15454 SDH) The Delete Link Management Protocol Control Channel (DLT-LMP-CTRL) command deletes an LMP control channel.

 
Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

DLT-LMP-CTRL:[<TID>]:<SRC>:<CTAG>;

Input Example

DLT-LMP-CTRL:PETALUMA:CTRL-3:704;

Input Parameters

<SRC>

The LMP control channel.

  • CTRL-ALL

Specifies all the control channels.

  • CTRL-{1-4}

Specifies an individual control channel.

10.16 DLT-LMP-TLINK

(Cisco ONS 15454 SDH) The Delete Link Management Protocol Traffic Engineering (TE) Link (DLT-LMP-TLINK) command deletes an LMP TE link.

 
Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

DLT-LMP-TLINK:[<TID>]:<SRC>:<CTAG>;

Input Example

DLT-LMP-TLINK:PETALUMA:TLINK-3:704;

Table 10-6 DLT-LMP-TLINK Command - Parameter Support

Input Parameters
Description

<SRC>

LMP TE link.

TLINK-ALL

Specifies all the TE links.

TLINK-{1-256}

Specifies an individual TE link.

10.17 DLT-LMP-DLINK

(Cisco ONS 15454 SDH) The Delete Link Management Protocol Data Link (DLT-LMP-DLINK) command deletes an LMP data link.

 
Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

DLT-LMP-DLINK:[<TID>]:<SRC>:<CTAG>;

Input Example

DLT-LMP-DLINK:PETALUMA:FAC-14-1-1:704;

Input Parameters

<SRC>

Access identifier from the “FACILITY” section.

10.18 DLT-LNK

(Cisco ONS 15454 SDH) The Delete Optical Link for OCH, OMS, or OTS (DLT-LNK) command deletes an optical link between two optical connection points. The optical link is specified by using the AIDs of the involved optical connection points.

 
Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-LNK:[<TID>]:<FROM>,<TO>:<CTAG>;

Input Example

DLT-LNK:PENNGROVE:BAND-6-1-TX,BAND-13-1-RX:114;

Input Parameters

<FROM>

The identifier at one end of the optical link from the AID “BAND” section.

<TO>

The identifier at the other end of the optical link from the AID “BAND” section.

10.19 DLT-LNKTERM

(Cisco ONS 15454 SDH) The Delete a Provisionable Patchcord Termination (DLT-LNKTERM) command deletes a provisionable patchcord termination present on a node. All termination points of a link/provisionable patchcord have to be deleted for the link to be deleted fully.

 
Usage Guidelines

  • This command accepts multiple AIDs, but does not accept the ALL AID.
  • A suitable error message will be returned if the link termination does not exist.

Category

Provisionable Patchcords

Security

Provisioning

Input Format

DLT-LNKTERM:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-LNKTERM::LNKTERM-1:CTAG;

Input Parameters

<AID>

Access identifier from the “LNKTERM” section. Indicates a link (provisionable patchcord) termination on the local node.

10.20 DLT-MA-CFM

(Cisco ONS 15454 SDH) The Delete Maintenance Association Connectivity Fault Management (DLT-MA-CFM) command deletes the maintenance association present on the card.

 
Usage Guidelines

  • The “ALL” AID is invalid for this command.
  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Equipment

Security

Provisioning

Input Format

DLT-MA-CFM:[<TID>]:<AID>:<CTAG>:::MANAME=<MANAME>,SVLANID=<SVLANID>;

Input Example

DLT-MA-CFM:454-156:SLOT-1:1:::MANAME=MANAME,SVLANID=4;

Input Parameters

<AID>

Access identifier from the “EQPT” section.

<MANAME>

Maintenance Association Name. It is a string. The MA name length should not exceed more than 43 characters.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.21 DLT-MD-CFM

(Cisco ONS 15454 SDH) The Delete Maintenance Domain Connectivity Fault Management (DLT-MD-CFM) command deletes the maintenance domain present on the card.

 
Usage Guidelines

  • The “ALL” AID is invalid for this command.
  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Equipment

Security

Provisioning

Input Format

DLT-MD-CFM:[<TID>]:<AID>:<CTAG>:::MDNAME=<MANAME>,LEVEL=<LEVEL>;

Input Example

DLT-MD-CFM:454-156:SLOT-1:1:::MDNAME=MDNAME,LEVEL=5;

Input Parameters

<AID>

Access identifier from the “EQPT” section.

<MDNAME>

Maintenance Domain Name. It is a string. The MD name length should not exceed more than 43 characters.

<LEVEL>

This indicates the level of the maintenance domain. The value ranges from 0 to 7.

10.22 DLT-MDMAMAP-CFM

(Cisco ONS 15454 SDH) The Delete Maintenance Domain and Maintenance Association mapping Connectivity Fault Management (DLT-MDMAMAP-CFM) command deletes the maintenance domain and maintenance association mapping.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Equipment

Security

Configuration

Input Format

DLT-MDMAMAP-CFM:[<TID>]:<AID>:<CTAG>:::MDNAME=<MANAME>,MAPACTION=<MAPACTION>,[MANAME=<MANAME>],[SVLANID=<SVLANID>];

Input Example

DLT-MDMAMAP-CFM::SLOT-17:1:::MDNAME=CISCO,MAPACTION=DETACH,MANAME=MA1,SVLANID=10;

Input Parameters

<AID>

Access identifier from the “EQPT” section.

<MDNAME>

Maintenance Association Name. It is a string. The MA name length should not exceed more than 43 characters.

<MAPACTION>

Describes the mapping action while deleting the attached MAs with MDs.

  • DETACH

Deletes the specified MA.

  • DETACH-ALL

Deletes all the MAs attached to the MD.

<MANAME>

Maintenance Association Name. It is a string. The MA name length should not exceed more than 43 characters.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.23 DLT-MEP-CFM

(Cisco ONS 15454 SDH) The Delete Maintenance End Point Connectivity Fault Management (DLT-MEP-CFM) command deletes the maintenance end points on the port.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Ports

Security

Provisioning

Input Format

DLT-MEP-CFM:[<TID>]:<AID>:<CTAG>:::SVLANID=<SVLANID>,MDNAME=<MDNAME>,MPID=<MPID>;

Input Example

DLT-MEP-CFM::ETH-12-3-1:1:::SVLANID=100,MDNAME=MD2,MPID=20;

Input Parameters

<AID>

Access identifier from the “ETH” section.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

<MDNAME>

Maintenance Domain Name. It is a string. The MD name length should not exceed more than 43 characters.

<MPID>

Maintenance Point Identifier. It is an integer.

10.24 DLT-MIP-CFM

(Cisco ONS 15454 SDH) The Delete Maintenance Intermediate Point Connectivity Fault Management (DLT-MIP-CFM) command deletes the maintenance intermediate points on the port.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Ports

Security

Provisioning

Input Format

DLT-MIP-CFM:[<TID>]:<AID>:<CTAG>:::VLANID=<VLANID>;

Input Example

DLT-MIP-CFM::ETH-1-1-1:1:::VLANID=2;

Input Parameters

<AID>

Access identifier from the “ETH” section.

<VLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.25 DLT-NNI-ETH

(Cisco ONS 15454 SDH) The Delete Ethernet Network-to-Network Interface (DLT-NNI-ETH) command deletes the NNI S-VLAN ID for the NNI of an L2 Ethernet port.

 
Usage Guidelines

  • The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use the RTRV-ETH command to obtain the current value.
  • If the AID is invalid, an IIAC (Invalid AID) error message is returned.
  • The ALL AID is invalid for this command.

Category

Ethernet

Security

Provisioning

Input Format

DLT-NNI-ETH:[<TID>]:<AID>:<CTAG>::<SVLANID>[::];

Input Example

DLT-NNI-ETH:PETALUMA:ETH-1-1-1:1::1010;

Input Parameters

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the “ETH” section.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.26 DLT-NNI-CHGRP

(Cisco ONS 15454 SDH) The Delete Channel Group Network-to-Network Interface (DLT-NNI-CHGRP) command deletes the NNI S-VLAN ID for the NNI of a channel group.

 
Usage Guidelines

  • The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use the RTRV-ETH command to obtain the current value.
  • If the AID is invalid, an IIAC (Invalid AID) error message is returned.
  • The ALL AID is invalid for this command.

Category

Channel group

Security

Provisioning

Input Format

DLT-NNI-CHGRP:[<TID>]:<AID>:<CTAG>::<SVLANID>[::];

Input Example

DLT-NNI-CHGRP:CISCO:CHGRP-1-1:1::1010;

Input Parameters

<AID>

Access identifier from the “CHGRP” section.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.27 DLT-OPMODE

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Delete Operating Mode (DLT-OPMODE) command deletes the operating mode created on the trunk. Operating mode cannot be deleted when ports are provisioned.

 
Usage Guidelines

  • Enter the Trunkport on which you want to delete the operating mode
  • Need not enter clientport, ctmap, or rate for deleting any operating mode.
  • In protect operating modes, enter the working trunk port number to delete that operating mode.
  • Client should not be provisioned to delete any opmode.

Category

DWDM

Security

Provisioning

Input Format

DLT-OPMODE:[<TID>]:<AID>:<CTAG>:::TRUNKPORT=<TRUNKPORT>;

Input Example

DLT-OPMODE::SLOT-2:1:::TRUNKPORT=2;

Input Parameters

<AID>

SLOT Access Identifier.

<TRUNKPORT>

Trunk port number of the operating mode being deleted.

10.28 DLT-QNQ-ETH

(Cisco ONS 15454 SDH) The Delete Ethernet QinQ (DLT-QNQ-ETH) command deletes the IEEE 802.1Q tunneling (QinQ) relationship between the CE-VLAN and the S-VLAN for Gigabit Ethernet uniport provisioning associated to an L2 Ethernet port.

 
Usage Guidelines

The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use the RTRV-ETH command to obtain the current value.

Category

Ethernet

Security

Provisioning

Input Format

DLT-QNQ-ETH:[<TID>]:<AID>:<CTAG>::<FIRSTCEVLANID>,<LASTCEVLANID>,
<SVLANID>[::];

Input Example

DLT-QNQ-ETH:PETALUMA:ETH-1-1-1:1::10,11,100;

Input Parameters

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the “ETH” section.

<FIRSTCEVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

<LASTCEVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.29 DLT-OCHCC

(Cisco ONS 15454 SDH) The Delete Optical Channel Client Connection (DLT-OCHCC) command deletes the OCH client connection.

 
Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],[CMDMDE=<CMDMDE>];

Input Example

DLT-OCHCC:VA454-22:FAC-2-1-1:116:::CKTID=\”OCHCC-1\”,CMDMDE=FRCD;

Table 10-7 DLT-OCHCC Command - Parameter Support

Input Parameters
Description

<AID>

Access identifier from the “FACILITY” section.

<CKTID>

(Optional) The default is Blank or None. String of ASCII characters. Maximum length is 48. Circuit identification parameter contains the Common Language Circuit ID or other alias of the circuit being provisioned. Cannot contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

  • FRCD

Force the system to override a state in which the command would normally be denied.

  • NORM

Execute the command normally. Do not override any conditions that might make the command fail.

10.30 DLT-OCHNC

(Cisco ONS 15454 SDH) The Delete Optical Channel Network Connection (DLT-OCHNC) command deletes the optical channel (OCH) network connection.

 
Usage Guidelines

Two OCHNC endpoints must be specified in order to identify the wavelength channel inside the node.

Category

DWDM

Security

Provisioning

Input Format

DLT-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>],[CMDMDE=<CMDMDE>];

Input Example

DLT-OCHNC:VA454-22:CHANWL-1-3-TX-1530.33,
CHANWL-4-1-RX-1530.33:116:::CKTID=CIRCUIT,CMDMDE=FRCD;

Table 10-8 DLT-OCHNC Command - Parameter Support

Input Parameters
Description

<SRC>

Source access identifier from the “CHANNEL” section. In two-way wavelength connection sources, both directions need to be indicated.

<DST>

Destination access identifier from the “LINE” section. In a two-way wavelength connection destination, both directions need to be indicated.

<CKTID>

(Optional) Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48.

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

  • FRCD

Force the system to override a state in which the command would normally be denied.

  • NORM

Execute the command normally. Do not override any conditions that might make the command fail.

10.31 DLT-QNQ-CHGRP

(Cisco ONS 15454 SDH) The Delete Channel Group QinQ (DLT-QNQ-CHGRP) command deletes the IEEE 802.1Q tunneling (QinQ) relationship between the CE-VLAN and the S-VLAN for Gigabit Ethernet uniport provisioning associated to a channel group.

 
Usage Guidelines

The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use the RTRV-ETH command to obtain the current value.

Category

Channel Group

Security

Provisioning

Input Format

DLT-QNQ-CHGRP:[<TID>]:<AID>:<CTAG>::<FIRSTCEVLANID>,<LASTCEVLANID>,
<SVLANID>[::];

Input Example

DLT-QNQ-CHGRP:CISCO:CHGRP-1-1:1::10,11,100;

Input Parameters

<AID>

Access identifier from the “CHGRP” section.

<FIRSTCEVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

<LASTCEVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

<SVLANID>

VLAN identifier. A VLAN ID is a number between 1 and 4096. The value 0 is reserved for untagged VLANs. This identifier is used for customer VLAN IDs and service provider VLAN IDs.

10.32 DLT-REP

(Cisco ONS 15454 SDH) The Delete Resilient Ethernet Protocol (DLT-REP) command deletes the ethernet port from the Resilient Ethernet Protocol (REP) segment.

 
Usage Guidelines

  • This command deletes all REP configuration configured on ETH ports on the card.
  • This command is only applicable if the card is in ETH-L2 card mode.
  • This command is applicable only to GE_XP and 10GE_XP cards.
  • If the port is not part of any segment, the NE generates an error message.

Category

Ethernet

Security

Provisioning

Input Format

DLT-REP:[TID]:<AID>:<CTAG>[:::];

Input Example

DLT-REP:CISCO:ETH-1-1-1-1:123;

Input Parameters

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the “ETH” section.

10.33 DLT-RMONTH-<MOD2_RMON>

(Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6) The Delete Remote Monitoring Threshold for 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, 8GFC, CHGRP, ETH, FSTE, G1000, GFPOS, GIGE, HDLC, OCH, POS, SDSDI , HDSDI, OTU1, OTU2, ISC3STP1G, or ISC3STP2G (DLT-RMONT-<MOD2_RMON>) command deletes a threshold entry in the remote monitoring (RMON) alarm table. Because multiple thresholds can be created for a particular montype, you must specify all the necessary parameters for the specific threshold that you want to delete. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

The command supports the modifier SDSDI , HDSDI, OTU1, OTU2, ISC3STP1G, and ISC3STP2G.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

Protection

Security

Provisioning

Input Format

DLT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,<INTVL>:
RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE],[STARTUP=<STARTUP>][:];

Input Example

DLT-RMONTH-GIGE:CISCO:FAC-2-1:1234::etherStatsOctets,,,,100:RISE=1000,FALL=100
SAMPLE=DELTA,STARTUP=RISING;

DLT-RMONTH-ISC3STP1G:CISCO:VFAC-4-2-1:1234::mediaIndStatsRxLcvErrors,,,,10:rise=10,fall=1,sample=absolute;

 

Table 10-9 DLT-RMONT-<MOD2_RMON> Command - Parameter Support

Input Parameters
Description

<SRC>

Source access identifier from the “FACILITY” section. AID for the facility that manages the data statistics. AR-MXP and AR-XP cards use the VFAC AID.

<MONTYPE>

Monitored type. Type of RMON monitored data statistics. The parameter type is ALL_MONTYPE, which is the monitoring type list.

  • AISSP

Alarm Indication Signal Seconds Path

  • ALL

All possible values

  • BBEP

SDH Background Block Errors Path

  • BBE-PM

OTN—Background Block Errors—Path Monitor Point

  • BBER

SDH Background Block Error Ratio

  • BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as one tenth of a percentage

  • BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as one tenth of a percentage

  • BBE-SM

OTN—Background Block Errors—Section Monitor Point

  • BIEC

FEC—Bit Errors Corrected

  • CGV

8B10B—Code Group Violations

  • CVCPP

Coding Violations—CP-Bit Path

  • ESL

Errored Seconds—Line

  • ESP

Errored Seconds—Path

  • ES-PM

OTN—Errored Seconds—Path Monitor Point

  • ESR

Errored Second—Ratio

  • ESR-PM

Errored Seconds Ratio—Path Monitor Point expressed as one tenth of a percentage

  • ESR-SM

Errored Seconds Ratio—Section Monitor Point expressed as one tenth of a percentage

  • ESS

Errored Seconds—Section

  • ES-SM

OTN—Errored Seconds—Section Monitor Point

  • ESV

Errored Seconds—VC Path

  • etherStatsBroadcastPkts

The total number of good packets received that were directed to a multicast address

  • etherStatsCollisions

Number of transmit packets that are collisions

  • etherStatsCRCAlignErrors

The total number of packets received that have a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets

  • etherStatsDropEvents

Number of received frames dropped at the port level

  • etherStatsFragments

The total number of packets received that were less than 64 octets

  • etherStatsJabbers

The total number of packets received that are longer than 1518 octets

  • etherStatsOctets

The total number of octets of data

  • etherStatsOversizePkts

The total number of packets received that are longer than 1518 octets

  • etherStatsPkts

The total number of packets (including bad packets, broadcast packets, and multicast packets) received

  • etherStatsUndersizePkts

The total number of packets received that are less than 64 octets

  • FCP

Failure Count—Line

  • FC-PM

OTN—Failure Count—Path Monitor Point

  • FC-SM

OTN—Failure Count—Section Monitor Point

  • HP-AR

Availability Ratio

  • HP-BBE

High-Order Path Background Block Error

  • HP-BBER

High-Order Path Background Block Error Ratio

  • HP-EB

High-Order Path Errored Block

  • HP-ES

High-Order Path Errored Second

  • HP-ESA

High-Order Path Errored Seconds–A

  • HP-ESB

High-Order Path Errored Seconds–B

  • HP-ESR

High-Order Path Errored Second Ratio

  • HP-FC

High-Order Path Failure Count

  • HP-NPJC-PDET

High-Order Path Negative Pointer Justification Count, Path Detected

  • HP-NPJC-PGEN

High-Order Path Negative Pointer Justification Count, Path Generated

  • HP-OI

High-Order path Outage Intensity

  • HP-PJCDIFF

High-Order Path Pointer Justification Count Difference

  • HP-PJCS-PDET

High-Order Path Pointer Justification Count, Path Detected

  • HP-PPJC-PDET

High-Order Path Positive Pointer Justification Count, Path Generated

  • HP-PPJC-PGEN

High-Order Path Positive Pointer Justification Count, Path Generated

  • HP-SEPI

The number of SEP events in available time

  • HP-SES

High-Order Path Severely Errored Seconds

  • HP-SESR

High-Order Path Severely Errored Second Ratio

  • HP-UAS

High-Order Path Unavailable Seconds

  • ifInBroadcastPkts

Number of broadcast packets received since the last counter reset

  • ifInDiscards

The number of inbound packets

  • ifInErrorBytePktss

Receive Error Byte

  • ifInErrors

The number of inbound packets (or transmission units) that contained errors

  • ifInFramingErrorPkts

Receive Framing Error

  • ifInJunkInterPkts

Receive Interpacket Junk

  • ifInMulticastPkts

Number of multicast packets received since the last counter reset

  • ifInOctets

Number of bytes transmitted since the last counter reset

  • ifInUcastPkts

Number of unicast packets received since the last counter reset

  • ifOutBroadcastPkts

Number of broadcast packets transmitted

  • ifOutDiscards

The number of outbound packets

  • ifOutErrors

The number of outbound packets (or transmission units) that could not be transmitted because of errors

  • ifOutMulticastPkts

Number of multicast packets transmitted

  • ifOutPayloadCrcErrors

Received payload cyclic redundancy check (CRC) errors

  • ifOutUcastPkts

Number of unicast packets transmitted

  • IOS

8B10B–Idle Ordered Sets

  • IPC

Invalid Packet Count

  • LBCL-AVG

Average Laser Bias current in micro A

  • LBCL-MAX

Maximum Laser Bias current in micro A

  • LBCL-MIN

Minimum Laser Bias current in micro A

  • LBCN

Normalized Laser Bias Current for STM1-8

  • LBCN-HWT

Laser bias current

  • LBCN-LWT

Laser bias current

  • LOSSL

Loss of Signal Seconds—Line

  • LP-BBE

Low-Order Path Background Block Error

  • LP-BBER

Low-Order Path Background Block Error Ratio

  • LP-EB

Low-Order Path Errored Block

  • LP-ES

Low-Order Path Errored Second

  • LP-ESA

Low-Order Path Errored Seconds–A

  • LP-ESB

Low-Order Path Errored Seconds–B

  • LP-ESR

Low-Order Path Errored Second Ratio

  • LP-FC

Low-Order Path Failure Count

  • LP-NPJC-DET

Low-Order Path Negative Pointer Justification Count, Detected

  • LP-NPJC-GEN

Low-Order Path Negative Pointer Justification Count, Generated

  • LP-PPJC-DET

Low-Order Path Positive Pointer Justification Count, Detected

  • LP-PPJC-GEN

Low Order path Positive Pointer Justification Count, Generated

  • LP-SEP

A sequence of between 3 to 9 consecutive severely errored seconds (SES)

  • LP-SEPI

Low-Order Path Severely Errored Period Intensity

  • LP-SES

Low-Order Path Severely Errored Seconds

  • LP-UAS

Low-Order Path Unavailable Seconds

  • MS-PSC

Protection switch count

  • MS-PSD

Protection switch duration

  • NIOS

8B10B—Non Idle Ordered Sets

  • NPJC-PDET

Negative Pointer Justification Count, Path Detected

  • NPJC-PGEN

Negative Pointer Justification Count, Path Generated

  • OPR-AVG

Average Receive Power in tenths of a microwatt

  • OPR-MAX

Maximum Receive Power in tenths of a microwatt

  • OPR-MIN

Minimum Receive Power in tenths of a microwatt

  • OPRN

Normalized Optical Receive Power for STM1-8

  • OPRN-MAX

Maximum value for OPRN

  • OPRN-MIN

Minimum value for OPRN

  • OPT-AVG

Average Transmit Power in tenths of a microwatt

  • OPT-MAX

Maximum Transmit Power in tenths of a microwatt

  • OPT-MIN

Minimum Transmit Power in tenths of a microwatt

  • OPTN

Normalized value for Optical Power Transmitted for STM1-8 card

  • OPTN-MAX

Maximum value for OPTN

  • OPTN-MIN

Minimum value for OPTN

  • OPWR-AVG

Optical Power—Average Interval Value in one tenth of dBm

  • OPWR-MAX

Optical Power—Maximum Interval Value in one tenth of dBm

  • OPWR-MIN

Optical Power—Minimum Interval Value in one tenth of dBm

  • PPJC-PDET

Positive Pointer Justification, Path Detected

  • PPJC-PGEN

Positive Pointer Justification, Path Detected

  • PSC

Protection Switching Count

  • PSC-R

Protection Switching Count—Ring

  • PSC-S

Protection Switching Count—Span

  • PSC-W

Protection Switching Count—Working

  • PSD

Protection Switching Duration

  • PSD-R

Protection Switching Duration—Ring

  • PSD-S

Protection Switching Duration—Span

  • PSD-W

Protection Switching Duration—Working

  • SASCPP

Severely Errored Framing/AIS Second—CP-Bit Path

  • SASP

Severely Errored Framing/AIS Seconds Path

  • SEFS

Severely Errored Framing Seconds

  • SESCPP

Severely Errored Second—CP-Bit Path

  • SESL

Severely Errored Second—Line

  • SESP

Severely Errored Second—Path

  • SES-PM

OTN—Severely Errored Second—Path

  • SESR

Severely Errored Second—Ratio

  • SESR-PM

OTN—Severely Errored Second Ratio—Path Monitor Point expressed as one tenth of a percentage

  • SESR-SM

OTN—Severely Errored Second Ratio—Section Monitor Point expressed as one tenth of a percentage

  • SESS

Severely Errored Second—Section

  • SES-SM

OTN—Severely Errored Second—Section Monitor Point

  • SESV

Severely Errored Second—VC Path

  • UASCPP

Unavailable Second—CP-Bit Path

  • UASL

Unavailable Second—Line

  • UASP

Unavailable Second—Path

  • UAS-PM

OTN—Unavailable Second—Path Monitor Point

  • UAS-SM

OTN—Unavailable Second—Section Monitor Point

  • UASV

Unavailable Second—VC Path

  • UNC-WORDS

FEC—Uncorrectable Words

  • VPC

Valid Packet Count

<INTVL>

The interval in seconds over which the data is sampled and compared with the rising and falling threshold. A valid value is any integer larger than or equal to 10 (seconds).

<RISE>

The rising threshold for the sampled statistics. A valid value is any integer.

<FALL>

The falling threshold. A valid value is any integer smaller than the rising threshold.

<SAMPLE>

(Optional) The method of calculating the value to be compared to the thresholds. The parameter type is SAMPLE_TYPE, which describes how the data will be calculated during the sampling period.

  • ABSOLUTE

Comparing directly.

  • DELTA

Comparing with the current value of the selected variable subtracted by the last sample.

<STARTUP>

(Optional) Dictates whether an event will generate if the first valid sample is greater than or equal to the rising threshold, less than or equal to the falling threshold, or both. The parameter type is STARTUP_TYPE, which indicates whether an event will be generated when the first valid sample is crossing the rising or falling threshold.

  • FALLING

Generates the event when the sample is smaller than or equal to the falling threshold.

  • RISING

Generates the event when the sample is greater than or equal to the rising threshold.

  • RISING-OR-FALLING

Generates the event when the sample is crossing the rising threshold, or the falling threshold.

10.34 DLT-ROLL-<MOD_PATH>

(Cisco ONS 15454 SDH) The Delete Roll for VC44C, VC464C, VC48C, VC4, VC416C, VC42C, or VC43C (DLT-ROLL-<MOD_PATH>) command deletes or completes an attempted rolling operation. See Table 27-1 for supported modifiers by platform.

 
Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

DLT-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::WHY=<WHY>;

Input Example

DLT-ROLL-VC4:CISCO:VC4-1-1-1,VC4-2-1-1:6:::WHY=STOP;

 

Table 10-10 DLT-ROLL-<MOD_PATH> Command - Parameter Support

Input Parameters
Description

<FROM>

Source access identifier from the “VC” section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the FROM-AID termination point. Otherwise, FROM is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters.

<TO>

Destination AID from the “VC” section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the TO-AID termination point. Otherwise, the TO is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters.

<WHY>

The reason for the deletion. The parameter type is WHY, which is the reason for the deletion.

  • END

Drop the leg to be rolled; the leg that is identified by the RFROM in the ENT-ROLL command.

  • STOP

The rolling operation will be deleted and reverted to the previous configuration.

10.35 DLT-ROUTE

(Cisco ONS 15454 SDH) The Delete Route (DLT-ROUTE) command deletes static routes.

 
Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-ROUTE:[<TID>]::<CTAG>::<DESPID>;

Input Example

DLT-ROUTE:CISCO::123::10.64.72.57;

Input Parameters

<DESPID>

Destination IP. DESPID is a string.

10.36 DLT-ROUTE-GRE

(Cisco ONS 15454 SDH) The Delete Route Generic Routing Encapsulation (DLT-ROUTE-GRE) command deletes a GRE tunnel.

 
Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-ROUTE-GRE:[<TID>]::<CTAG>:::IPADDR=<IPADDR>,
IPMASK=<IPMASK>,NSAP=<NSAP>;

Input Example

DLT-ROUTE-GRE:CISCO::123:::IPADDR=10.64.72.57,IPMASK=255.255.255.0,
NSAP=39840F80FFFFFF0000DDDDAA000010CFB4910200;

 

Table 10-11 DLT-ROUTE-GRE Command - Parameter Support

Input Parameters
Description

<IPADDR>

IP address of the tunnel endpoint. IPADDR is a string.

<IPMASK>

Subnet mask for the tunnel endpoint. IPMASK is a string

<NSAP>

Network service access point (NSAP) address for the tunnel endpoint. NSAP is a string.

10.37 DLT-TADRMAP

(Cisco ONS 15454 SDH) The Delete TID Address Mapping (DLT-TADRMAP) command instructs a gateway NE to delete an entry in the TADRMAP table.

 
Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-TADRMAP:[<TID>]::<CTAG>:::[TIDNAME=<TIDNAME>],[ADDRTYPE=<ADDRTYPE>];

Input Example

DLT-TADRMAP:DXT::CTAG:::TIDNAME=ENENODENAME,ADDRTYPE=IP;

 

Table 10-12 DLT-TADRMAP Command - Parameter Support

Input Parameters
Description

<TIDNAME>

(Optional) TID of the entity to be removed from the TADRMAP. TIDNAME is a string.

<ADDRTYPE>

(Optional) Specifies to remove an IP, NSAP, or IP-AND-NSAP entry in the TADRMAP. The parameter type is ADDRTYPE, which specifies whether the address is an IP address or an NSAP address.

  • IP

IP address

  • IP-AND-NSAP

IP and NSAP address

  • NSAP

NSAP address

10.38 DLT-TRAPTABLE

(Cisco ONS 15454 SDH) The Delete Trap Table (DLT-TRAPTABLE) command deletes an SNMP (Simple Network Management Protocol) trap destination entry.

 
Usage Guidelines

Entering ALL will delete the whole table.

Category

System

Security

Provisioning

Input Format

DLT-TRAPTABLE:[<TID>]:<AID>:<CTAG>;

Input Examples

1. DLT-TRAPTABLE::1.2.3.4:1;

2. DLT-TRAPTABLE::“[3ffe:0501:0008:0000:0260:97ff:fe40:efab]”:1;

Input Parameters

<AID>

Access identifier from the “IPADDR” section. IP address identifies the trap destination. Only numeric IP addresses are allowed.

10.39 DLT-TUNNEL-FIREWALL

(Cisco ONS 15454 SDH) The Delete Tunnel Firewall (DLT-TUNNEL-FIREWALL) command deletes a firewall tunnel.

 
Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-TUNNEL-FIREWALL:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>],
[SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>];

Input Example

DLT-TUNNEL-FIREWALL:TID::CTAG:::SRCADDR=192.168.100.52,
SRCMASK=255.255.255.0,DESTADDR=192.168.101.14,DESTMASK=255.255.255.0;

Table 10-13 DLT-TUNNEL-FIREWALL Command - Parameter Support

Input Parameters
Description

<SRCADDR>

(Optional) Source IP address. SRCADDR is a string.

<SRCMASK>

(Optional) Source mask. SRCMASK is a string.

<DESTADDR>

(Optional) Destination IP address. DESTADDR is a string.

<DESTMASK>

(Optional) Destination mask. DESTMASK is a string.

10.40 DLT-TUNNEL-PROXY

(Cisco ONS 15454 SDH) The Delete Tunnel Proxy (DLT-TUNNEL-PROXY) command deletes a proxy tunnel.

 
Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-TUNNEL-PROXY:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>],
[SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>];

Input Example

DLT-TUNNEL-PROXY:TID::CTAG:::SRCADDR=192.168.100.52,
SRCMASK=255.255.255.0,DESTADDR=192.168.101.14,DESTMASK=255.255.255.0;

Table 10-14 DLT-TUNNEL-PROXY Command - Parameter Support

Input Parameters
Description

<SRCADDR>

(Optional) Source IP address. SRCADDR is a string.

<SRCMASK>

(Optional) Source mask. SRCMASK is a string.

<DESTADDR>

(Optional) Destination IP address. DESTADDR is a string.

<DESTMASK>

(Optional) Destination mask. DESTMASK is a string.

10.41 DLT-USER-SECU

(Cisco ONS 15454 SDH) The Delete User Security (DLT-USER-SECU) command deletes a user and can only be performed by a Superuser. Privilege levels are described in the ENT-USER-SECU command.

 
Usage Guidelines

This command cannot be used to delete a user that is currently logged on.

Syntax of the UID parameter is not checked. The user is deleted if the UID exists in the database.

Category

Security

Security

Superuser

Input Format

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>;

Input Example

DLT-USER-SECU:PETALUMA:CISCO15:123;

Input Parameters

 

<UID>

User identifier. Can be up to 10 alphanumeric characters. UID is a string.

10.42 DLT-VCG

(Cisco ONS 15454 SDH) The Delete Virtual Concatenated Group (DLT-VCG) command deletes a VCG object.

 
Usage Guidelines

None

Category

VCAT

Security

Provisioning

Input Format

DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:];

Input Example

DLT-VCG:NODE1:FAC-1-1:1234:::CMDMDE=FRCD;

 

Table 10-15 DLT-VCG Command - Parameter Support

Input Parameters
Description

<SRC>

Source AID from the “FACILITY” section. ML-Series cards use the VFAC AID and FC_MR-4 cards use the FAC AID.

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

FRCD

Force the system to override a state where the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that might make the command fail.

10.43 DLT-VLAN

(Cisco ONS 15454 SDH) The Delete Virtual LAN (DLT-VLAN) command deletes a VLAN from the VLAN database. The VLAN database is a collection of VLANs used in a NE.

 
Usage Guidelines

  • If the AID is invalid, an IIAC (Invalid AID) error message is returned.
  • The ALL AID is invalid for this command.

Category

Ethernet

Security

Provisioning

Input Format

DLT-VLAN:[<TID>]:<AID>:<CTAG>[::::];

Input Example

DLT-VLAN:PETALUMA:VLAN-4096:1;

Input Parameters

<AID>

The AID is used to access the VLAN.

  • VLAN-{0-4096}

The AID used for a single VLAN. VLAN ID 0 is reserved for untagged VLANs.

10.44 DLT-WDMANS

(Cisco ONS 15454 SDH) The Delete Wavelength Division Multiplexing Automatic Node Setup (DLT-WDMANS) command deletes the automatic optical node setup application attributes.

 
Usage Guidelines

  • If the AID is invalid, an IIAC (Invalid AID) error message is returned.
  • The ALL AID is invalid for this command.

Category

DWDM

Security

Maintenance

Input Format

DLT-WDMANS:[<TID>]:<AID>:<CTAG>::<PARAM>,[<WLEN>][::];

Input Example

DLT-WDMANS:PENNGROVE:WDMNODE:114::VOAATT,1530.33;

Input Parameters

<AID>

The AID is used to access the WDM node or a single port of the DWDM node.

  • WDMNODE

Indicates the WDM node of an MSTP and accesses the NTWTYPE and DITHERWDMANS node parameters.

  • LINE

The optical transport section port.

  • BAND

The optical multiplex section port.

  • CHAN

The optical channel port.

<WLEN>

(Optional) The parameter type is OPTICAL_WLEN, which indicates the optical wavelength.

  • 1310

Wavelength 1310

  • 1470

Wavelength 1470

  • 1490

Wavelength 1490

  • 1510

Wavelength 1510

  • 1528.77

Wavelength 1528.77

  • 1529.55

Wavelength 1529.55

  • 1529.94

Wavelength 1529.94

  • 1530

Wavelength 1530

  • 1530.33

Wavelength 1530.33

  • 1530.73

Wavelength 1530.73

  • 1531.12

Wavelength 1531.12

  • 1531.51

Wavelength 1531.51

  • 1531.90

Wavelength 1531.90

  • 1532.29

Wavelength 1532.29

  • 1532.68

Wavelength 1532.68

  • 1533.07

Wavelength 1533.07

  • 1533.47

Wavelength 1533.47

  • 1533.86

Wavelength 1533.86

  • 1534.25

Wavelength 1534.25

  • 1534.64

Wavelength 1534.64

  • 1535.04

Wavelength 1535.04

  • 1535.43

Wavelength 1535.43

  • 1535.82

Wavelength 1535.82

  • 1536.22

Wavelength 1536.22

  • 1536.61

Wavelength 1536.61

  • 1537

Wavelength 1537

  • 1537.40

Wavelength 1537.40

  • 1537.79

Wavelength 1537.79

  • 1538.19

Wavelength 1538.19

  • 1538.58

Wavelength 1538.58

  • 1538.98

Wavelength 1538.98

  • 1539.37

Wavelength 1539.37

  • 1539.77

Wavelength 1539.77

  • 1540.16

Wavelength 1540.16

  • 1540.56

Wavelength 1540.56

  • 1540.95

Wavelength 1540.95

  • 1541.35

Wavelength 1541.35

  • 1541.75

Wavelength 1541.75

  • 1542.14

Wavelength 1542.14

  • 1542.35

Wavelength 1542.35

  • 1542.54

Wavelength 1542.54

  • 1542.94

Wavelength 1542.94

  • 1543.33

Wavelength 1543.33

  • 1543.73

Wavelength 1543.73

  • 1544.13

Wavelength 1544.13

  • 1544.53

Wavelength 1544.53

  • 1544.92

Wavelength 1544.92

  • 1545.32

Wavelength 1545.32

  • 1545.72

Wavelength 1545.72

  • 1546.12

Wavelength 1546.12

  • 1546.52

Wavelength 1546.52

  • 1546.92

Wavelength 1546.92

  • 1547.32

Wavelength 1547.32

  • 1547.72

Wavelength 1547.72

  • 1548.12

Wavelength 1548.12

  • 1548.51

Wavelength 1548.51

  • 1548.92

Wavelength 1548.92

  • 1549.32

Wavelength 1549.32

  • 1549.71

Wavelength 1549.71

  • 1550

Wavelength 1500

  • 1550.12

Wavelength 1550.12

  • 1550.52

Wavelength 1550.52

  • 1550.92

Wavelength 1550.92

  • 1551.32

Wavelength 1551.32

  • 1551.72

Wavelength 1551.72

  • 1552.12

Wavelength 1552.12

  • 1552.52

Wavelength 1552.52

  • 1552.93

Wavelength 1552.93

  • 1553.33

Wavelength 1553.33

  • 1553.73

Wavelength 1553.73

  • 1554.13

Wavelength 1554.13

  • 1554.13

Wavelength 1554.13

  • 1554.94

Wavelength 1554.94

  • 1555.34

Wavelength 1555.34

  • 1555.75

Wavelength 1555.75

  • 1556.15

Wavelength 1556.15

  • 1556.55

Wavelength 1556.55

  • 1556.96

Wavelength 1556.96

  • 1557.36

Wavelength 1557.36

  • 1557.77

Wavelength 1557.77

  • 1558.17

Wavelength 1558.17

  • 1558.58

Wavelength 1558.58

  • 1558.98

Wavelength 1558.98

  • 1559.39

Wavelength 1559.39

  • 1559.79

Wavelength 1559.79

  • 1560.20

Wavelength 1560.20

  • 1560.61

Wavelength 1560.61

  • 1561.01

Wavelength 1561.01

  • 1561.42

Wavelength 1561.42

  • 1561.83

Wavelength 1561.83

  • 1570

Wavelength 1570

  • 1570.83

Wavelength 1570.83

  • 1571.24

Wavelength 1571.24

  • 1571.65

Wavelength 1571.65

  • 1572.06

Wavelength 1572.06

  • 1572.48

Wavelength 1572.48

  • 1572.89

Wavelength 1572.89

  • 1573.30

Wavelength 1573.30

  • 1573.71

Wavelength 1573.71

  • 1574.13

Wavelength 1574.13

  • 1574.54

Wavelength 1574.54

  • 1574.95

Wavelength 1574.95

  • 1575.37

Wavelength 1575.37

  • 1575.78

Wavelength 1575.78

  • 1576.20

Wavelength 1576.20

  • 1576.61

Wavelength 1576.61

  • 1577.03

Wavelength 1577.03

  • 1577.44

Wavelength 1577.44

  • 1577.86

Wavelength 1577.86

  • 1578.27

Wavelength 1578.27

  • 1578.69

Wavelength 1578.69

  • 1579.10

Wavelength 1579.10

  • 1579.52

Wavelength 1579.52

  • 1579.93

Wavelength 1579.93

  • 1580.35

Wavelength 1580.35

  • 1580.77

Wavelength 1580.77

  • 1581.18

Wavelength 1581.18

  • 1581.60

Wavelength 1581.60

  • 1582.02

Wavelength 1582.02

  • 1582.44

Wavelength 1582.44

  • 1582.85

Wavelength 1582.85

  • 1583.27

Wavelength 1583.27

  • 1583.69

Wavelength 1583.69

  • 1584.11

Wavelength 1584.11

  • 1584.53

Wavelength 1584.53

  • 1584.95

Wavelength 1584.95

  • 1585.36

Wavelength 1585.36

  • 1585.78

Wavelength 1585.78

  • 1586.20

Wavelength 1586.20

  • 1586.62

Wavelength 1586.62

  • 1587.04

Wavelength 1587.04

  • 1587.46

Wavelength 1587.46

  • 1587.88

Wavelength 1587.88

  • 1588.30

Wavelength 1588.30

  • 1588.73

Wavelength 1588.73

  • 1589.15

Wavelength 1589.15

  • 1589.57

Wavelength 1589.57

  • 1589.99

Wavelength 1589.99

  • 1590

Wavelength 1590

  • 1590.41

Wavelength 1590.41

  • 1590.83

Wavelength 1590.83

  • 1591.26

Wavelength 1591.26

  • 1591.68

Wavelength 1591.68

  • 1592.10

Wavelength 1592.10

  • 1592.52

Wavelength 1592.52

  • 1592.95

Wavelength 1592.95

  • 1593.37

Wavelength 1593.37

  • 1593.79

Wavelength 1593.79

  • 1594.22

Wavelength 1594.22

  • 1594.64

Wavelength 1594.64

  • 1595.06

Wavelength 1595.06

  • 1595.49

Wavelength 1595.49

  • 1596.34

Wavelength 1596.34

  • 1596.76

Wavelength 1596.76

  • 1597.19

Wavelength 1597.19

  • 1597.62

Wavelength 1597.62

  • 1598.04

Wavelength 1598.04

  • 1598.47

Wavelength 1598.47

  • 1598.89

Wavelength 1598.89

  • 1599.32

Wavelength 1599.32

  • 1599.75

Wavelength 1599.75

  • 1600.06

Wavelength 1600.06

  • 1601.03

Wavelength 1601.03

  • 1601.46

Wavelength 1601.46

  • 1601.88

Wavelength 1601.88

  • 1602.31

Wavelength 1602.31

  • 1602.74

Wavelength 1602.74

  • 1603.17

Wavelength 1603.17

  • 1603.60

Wavelength 1603.60

  • 1604.03

Wavelength 1604.03

  • 1610

Wavelength 1610

<VOAATTN>

The value of calibrated attenuation for the VOA expressed in dBm. The range is 0.0 to +30.0. VOAATTN is a float.

<POWEROSC>

WDM-ANS OSC power parameter.

<NTWTYPE>

WDM-ANS network type parameter.

<CHLOSS>

WDM-ANS channel loss parameter.

<GAIN>

WDM-ANS amplifier gain parameter.

<TILT>

WDM-ANS amplifier tilt parameter.

<CHPWR>

WDM-ANS channel power parameter.

<AMPLMODE

WDM-ANS amplifier mode parameter.

<RATIO>

WDM-ANS Raman amplifier pump ratio parameter.

<OSCLOSS>

WDM-ANS OSC channel loss parameter.

<DITHER>

WDM-ANS WXC dithering parameter.

<TOTALPWR>

WDM-ANS Raman amplifier total power in mW.

<HIGHSLVEXP>

Span loss verification—high value.

<LOWSLVEXP>

Span loss verification—low value.

10.45 DLT-WDMSIDE

(Cisco ONS 15454 SDH) The Delete Wavelength Division Multiplexing Side (DLT-WDMSIDE) command deletes a WDM side.

 
Usage Guidelines

  • If the AID is invalid, an IIAC (Invalid AID) error message is returned.
  • The ALL AID is invalid for this command.

Category

DWDM

Security

Maintenance

Input Format

DLT-WDMSIDE:[<TID>]:<AID>:<CTAG>[::::];

Input Example

DLT-WDMSIDE:PENNGROVE:WDMSIDE-A:114;

Input Parameters

<AID>

The AID used to access the WDM side of a Multiservice Transport Platform (MSTP) node.

  • WDMSIDE-{UNKNOWN,A,B,C,D,E,F,G,H}

MSTP side identifier.