Cisco ONS SDH TL1 Command Guide, Release 9.3
Chapter 20, RST Commands
Downloads: This chapterpdf (PDF - 322.0KB) The complete bookPDF (PDF - 12.47MB) | Feedback

Table of Contents

RST Commands

RST Commands

This chapter provides restore (RST) commands for the Cisco ONS 15454 SDH, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.


Note All commands supported on the Cisco ONS 15454 SDH platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.


20.1 RST-<MOD2>

(Cisco ONS 15454 SDH) The Restore 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 5GIB, 8GFC, CLNT, D1VIDEO, DS3I, DV6000, DVBASI, E1, E3, E4, ESCON, ETRCLO, ETH, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, OCH, OMS, OTS, OTU3, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, STS36C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (RST-<MOD2>) command provisions a facility as In Service (IS).

 
Usage Guidelines

See Table 27-1 for supported modifiers by platform.


Note This command can only be executed when the port is in the Locked and Maintenance state.


Category

Ports

Security

Maintenance

Input Format

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];

Input Example

RST-E1:CISCO:FAC-1-1:1::::UNLOCKED,AUTOMATICINSERVICE;

 

Table 20-1 Parameter Support

Parameter
Description
Cisco ONS 15454 SDH

<AID>

Access identifier from the “ALL” section.

Y

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

  • Unlocked

In service

Y

  • Locked

Out of service

Y

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

  • AutomaticInService

Automatic in service

Y

  • Disabled

Disabled

Y

  • Loopback

Loopback

Y

  • MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

  • Maintenance

Maintenance mode

Y

  • OutOfGroup

Out of group

Y

  • SoftwareDownload

Software downloading

Y

  • Unassigned

Unassigned

Y

  • NotInstalled

Unequipped

Y

20.2 RST-EQPT

(Cisco ONS 15454 SDH) The Restore Equipment (RST-EQPT) command provisions equipment into the In-Service state from the Maintenance state.

 
Usage Guidelines

This command is only applicable to equipment that is in transition from the Maintenance state to the In-Service state.

Category

Equipment

Security

Maintenance

Input Format

RST-EQPT:[<TID>]:<AID>:<CTAG>[::];

Input Example

RST-EQPT:CISCO:SLOT-1:1;

Input Parameters

<AID>

Access identifier from the “EQPT” section.