Cisco ONS SDH TL1 Command Guide, Releases 9.2.1 and 9.2.2
Chapter 26, Conditions
Downloads: This chapterpdf (PDF - 484.0KB) The complete bookPDF (PDF - 13.19MB) | Feedback

Table of Contents

Conditions

Conditions

This chapter lists the conditions for TL1 commands and autonomous messages for the Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6, and Cisco ONS 15600 SDH, Release 9.2.1. These conditions are listed below.

Conditions include any problem detected on an Cisco ONS 15454 SDH, Cisco ONS 15454 M2, Cisco ONS 15454 M6, or Cisco ONS 15600 SDH shelf. They can include standing or transient notifications. A snapshot of all current raised, standing conditions on the network, node, or card can be retrieved in the Cisco Transport Controller (CTC) Conditions window or using the RTRV-COND commands. (In addition, some but not all cleared conditions are also found in the History tab in CTC.)


Note The Condition that apply to Cisco ONS 15454 SDH also applies to Cisco ONS 15454 M2 and Cisco ONS 15454 M6.


 

Table 26-1 Conditions

Condition
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH

AIS

Alarm Indication Signal

Y

Y

AIS-L

Alarm Indication Signal—Line

Y

Y

ALS

Automatic Laser Shutdown

Y

Y

AMPLI-INIT

Optical Amplifier Initialization

Y

Y

APC-DISABLED

Automatic Power Control Disabled

Y

Y

APC-FAIL

Automatic Power Control Failure

Y

Y

APSB

Byte Failure

Y

Y

APSC-IMP

Improper Automatic Protection Switch (APS) Code

Y

Y

APSCDFLTK

Default K Byte

Y

Y

APSCINCON

Inconsistent APS Code

Y

Y

APSCM

Protection Switching Channel Match Failure

Y

Y

APSCNMIS

Node ID Mismatch

Y

Y

APSIMP

APS Invalid Mode

Y

Y

APSMM

APS Mode Mismatch

Y

Y

AS-CMD

Alarms Suppressed By User Command

Y

Y

AS-MT

Alarms Suppressed For Maintenance

Y

Y

AU-AIS

AIS—Administration Unit—Alarm Indication Signal

Y

Y

AU-LOF

LOF—Administration Unit—Loss of Multi Frame

Y

Y

AU-LOP

LOP—Administration Unit—Loss of Pointer

Y

Y

AUD-LOG-LOSS

Audit Log 100 Percent Full—Oldest records will be lost

Y

Y

AUD-LOG-LOW

Audit Log 80 Percent Full

Y

Y

AUTOLSROFF

Automatic Laser Shutoff Due To High Temperature

Y

Y

AUTORESET

Automatic System Reset

Y

Y

AUTOSW-AIS-SNCP

Automatic SNCP Switch caused by AIS

Y

Y

AUTOSW-LOP-SNCP

Automatic SNCP Switch Caused By LOP

Y

Y

AUTOSW-PDI-SNCP

Automatic SNCP Switch Caused By PDI

Y

Y

AUTOSW-SDBER-SNCP

Automatic SNCP Switch Caused By SDBER

Y

Y

AUTOSW-SFBER-SNCP

Automatic SNCP Switch Caused By SFBER

Y

Y

AUTOSW-UNEQ-SNCP

Automatic SNCP Switch Caused By UNEQ

Y

Y

AWG-DEG

AWG Temperature Degrade

Y

Y

AWG-FAIL

AWG Temperature Failure

Y

Y

AWG-OVERTEMP

AWG Over-Temperature

Y

Y

AWG-WARM-UP

AWG Warm Up

Y

Y

BAT-FAIL

Battery Failure

Y

Y

BAT-HGH-VLT

High Volt

Y

Y

BAT-LOW-VLT

Low Volt

Y

Y

BKUPMEMP

Primary Non-Volatile Backup Memory Failure

Y

Y

CARLOSS

Carrier Loss On The LAN

Y

Y

CASETEMP-DEG

Case Temperature Degrade

Y

Y

CKTDOWN

Signaling unable to set up circuit

Y

Y

CLDRESTART

Cold Restart

Y

Y

COMIOXC

IO Slot To XCON Communication Failure

Y

Y

COMM-FAIL

Plug-in Module Communication Failure

Y

Y

CONTBUS-A-18

TCC A To DCC A Processor Communication Failure

Y

Y

CONTBUS-B-18

TCC B To DCC B Processor Communication Failure

Y

Y

CONTBUS_A

Controller A To Shelf Slot Communication Failure

Y

Y

CONTBUS_B

Controller B To Shelf Slot Communication Failure

Y

Y

CTNEQPT-MISMATCH

Connection Equipment Mismatch

Y

Y

CTNEQPT-PBPROT

Interconnection Equipment Failure—Protect XC Payload Bus

Y

Y

CTNEQPT-PBWORK

Interconnection Equipment Failure—Working XC Payload Bus

Y

Y

DATAFLT

Software Fault—Data Integrity Fault

Y

Y

DBOSYNC

Standby Database Out of Sync

Y

Y

DS3-MISM

DS3 Frame Format Mismatch

Y

Y

DSP-COMM-FAIL

DSP Communication Failure

Y

Y

DSP-FAIL

DSP Failure

Y

Y

DUP-IPADDR

IP address already in use within the same DCC Area

Y

Y

DUP-NODENAME

Node name already in use within the same DCC area

Y

Y

E-W-MISMATCH

Both Ends Of Fiber Provisioned As East Or Both As West

Y

Y

E3-ISD

E3 Idle Condition

Y

Y

EHIBATVG

Extreme High Volt

Y

Y

ELWBATVG

Extreme Low Volt

Y

Y

EOC

RS-DCC Termination Failure

Y

Y

EQPT

Equipment Failure

Y

Y

EQPT-MISS

Replaceable Equipment/Unit is Missing

Y

Y

ERFI-P-CONN

Enhanced Remote Failure Indication—Path—Connectivity

Y

Y

ERFI-P-PAYLD

Enhanced Remote Failure Indication—Path—Payload

Y

Y

ERFI-P-SRVR

Enhanced Remote Failure Indication—Path—Server

Y

Y

ERROR-CONFIG

Error in Startup Configuration

Y

Y

ETH-LINKLOSS

Rear Panel Ethernet Link Removed

Y

Y

EXCCOL

Excess Collisions On The LAN

Y

Y

EXERCISE-RING-FAIL

Exercise Request on Ring Failed

Y

Y

EXERCISE-RING-REQ

Exercise Request on Ring

Y

Y

EXERCISE-SPAN-FAIL

Exercise Request on Span Failed

Y

Y

EXERCISE-SPAN-REQ

Exercise Request on Span

Y

Y

EXT

Failure Detected External To The NE

Y

Y

EXTRA-TRAF-PREEMPT

Extra Traffic Preempted

Y

Y

FAILTOSW

Failure To Switch To Protection

Y

Y

FAILTOSW-HO

Failure To Switch To Protection—High Order Path

Y

Y

FAILTOSW-LO

Failure To Switch To Protection—Low Order Path

Y

Y

FAILTOSWR

Failure To Switch To Protection—Ring

Y

Y

FAILTOSWS

Failure To Switch To Protection—Span

Y

Y

FAN

Fan Failure

Y

Y

FANDEGRADE

Partial Fan Failure

Y

Y

FE-AIS

Far End AIS

Y

Y

FE-DS1-MULTLOS

Far End Multiple DS1 LOS Detected On DS3

Y

Y

FE-DS1-NSA

Far End DS1 Equipment Failure—Non Service Affecting

Y

Y

FE-DS1-SA

Far End DS1 Equipment Failure—Service Affecting

Y

Y

FE-DS1-SNGLLOS

Far End Single DS1 LOS

Y

Y

FE-DS3-NSA

Far End DS3 Equipment Failure—Non Service Affecting

Y

Y

FE-DS3-SA

Far End DS3 Equipment Failure—Service Affecting

Y

Y

FE-E1-MULTLOS

Far end multiple E1 LOS detected on E3

Y

Y

FE-E1-NSA

Far end E1 eqpt fail non service affecting

Y

Y

FE-E1-SA

Far end E1 eqpt fail service affecting

Y

Y

FE-E1-SNGLLOS

Far end signal E1 LOS

Y

Y

FE-E3-NSA

Far end E3 eqpt fail non service affecting

Y

Y

FE-E3-SA

Far end E3 eqpt fail service affecting

Y

Y

FE-EQPT-NSA

Far End Common Equipment Failure—Non Service Affecting

Y

Y

FE-EXERCISING-RING

Far End Exercising Ring

Y

Y

FE-EXERCISING-SPAN

Far End Exercising Span

Y

Y

FE-FRCDWKSWPR-RING

Far End Working Facility Forced To Switch To Protection—Ring

Y

Y

FE-FRCDWKSWPR-SPAN

Far End Working Facility Forced To Switch To Protection—Span

Y

Y

FE-IDLE

Far End IDLE

Y

Y

FE-LOCKOUTOFPR-ALL

Far End Lockout Of Protection—All Spans

Y

Y

FE-LOCKOUTOFPR-RING

Far End Lockout Of Protection—Ring

Y

Y

FE-LOCKOUTOFPR-SPAN

Far End Lockout Of Protection—Span

Y

Y

FE-LOCKOUTOFWK-RING

Far End Lockout Of Working—Ring

Y

Y

FE-LOCKOUTOFWK-SPAN

Far End Lockout Of Working—Span

Y

Y

FE-LOF

Far End LOF

Y

Y

FE-LOS

Far End LOS

Y

Y

FE-MANWKSWPR-RING

Far End Manual Switch Of Working Facility To Protection—Ring

Y

Y

FE-MANWKSWPR-SPAN

Far End Manual Switch Of Working Facility To Protection—Span

Y

Y

FE-SDPRLF

APS Channel—Far End Protection Line Signal Degrade

Y

Y

FEC-MISM

FEC Mismatch

Y

Y

FEPRLF

Far End Protection Line Failure

Y

Y

FIBERTEMP-DEG

Fiber Temperature Degrade

Y

Y

FORCED-REQ

Forced Switch Request

Y

Y

FORCED-REQ-RING

Forced Switch Request On Ring

Y

Y

FORCED-REQ-SPAN

Forced Switch Request On Span

Y

Y

FRCDSWTOINT

Forced Switch To Internal Clock

Y

Y

FRCDSWTOPRI

Forced Switch To Primary Reference

Y

Y

FRCDSWTOSEC

Forced Switch To Second Reference

Y

Y

FRCDSWTOTHIRD

Forced Switch To Third Reference

Y

Y

FRNGSYNC

Free Running Synchronization Mode

Y

Y

FSTSYNC

Fast Start Synchronization Mode

Y

Y

FULLPASSTHR-BI

Bidirectional Full Pass Through Is Active

Y

Y

GAIN-HDEG

Optical Amplifier Gain Degrade High

Y

Y

GAIN-HFAIL

Optical Amplifier Gain Failure High

Y

Y

GAIN-LDEG

Optical Amplifier Gain Degrade Low

Y

Y

GAIN-LFAIL

Optical Amplifier Gain Failure Low

Y

Y

GCC-EOC

GCC Termination Failure

Y

Y

GE-OOSYNC

Gigabit Ethernet Out of Sync

Y

Y

HI-LASERBIAS

Equipment High Laser Bias

Y

Y

HI-RXPOWER

Equipment High Receive Power

Y

Y

HI-TXPOWER

Equipment High Transmit Power

Y

Y

HITEMP

High Temperature

Y

Y

HLDOVRSYNC

Holdover Synchronization Mode

Y

Y

HP-RFI

Remote Failure Indication—High Order—Remote Failure/Alarm Indication

Y

Y

HP-TIM

High Order—Trace Identifier Mismatch Failure

Y

Y

HP-UNEQ

Signal Label Mismatch Failure (SLMF)—Unequipped High Order—Path Unequipped

Y

Y

I-HITEMP

Industrial High Temperature

Y

Y

IMPROPRMVL

Improper Removal

Y

Y

INC-GFP-OUTOFFRAME

Out Of Frame Detected by Generic Framing Protocol (GFP) Receiver

Y

Y

INC-GFP-SIGLOSS

Client Signal Loss Frames Detected by GFP Receiver

Y

Y

INC-ISD

DS3 Idle Condition

Y

Y

INC-SIGLOSS

Incoming Signal Loss on Fibre Channel Interface

Y

Y

INC-SYNCLOSS

Incoming Synchronization Loss on Fibre Channel Interface

Y

Y

INC_GFP_SYNCLOSS

Client Synchronization Loss Frames Detected by GFP Receiver

Y

Y

INHSWPR

Inhibit Switch To Protect Request On Equipment

Y

Y

INHSWWKG

Inhibit Switch To Working Request On Equipment

Y

Y

INTRUSION-PSWD

Security Intrusion Attempt Detected—See Audit Log

Y

Y

INVMACADR

Invalid MAC Address

Y

Y

IOSCFGCOPY

Ios Config Copy In Progress

Y

Y

KB-PASSTHR

K Bytes Pass-Through Is Active

Y

Y

KBYTE-APS-CHANNEL-FAILURE

Kbyte Channel Failure

Y

Y

LAN-POL-REV

Lan Connection Polarity Reversed

Y

Y

LASER-APR

Laser Auto Power Reduction

Y

Y

LASERBIAS-DEG

Laser Bias Degrade

Y

Y

LASERBIAS-FAIL

Laser Bias Failure

Y

Y

LASEREOL

Laser Approaching End of Life

Y

Y

LASERTEMP-DEG

Laser Temperature Degrade

Y

Y

LKOUTPR-R

Lockout Of Protection—Ring

Y

Y

LKOUTPR-S

Lockout Of Protection—Span

Y

Y

LKOUTWK-R

Lockout Of Working—Ring

Y

Y

LKOUTWK-S

Lockout Of Working—Span

Y

Y

LMP-HELLODOWN

Link Management Protocol (LMP) Hello FSM to Control Channel down

Y

Y

LMP-NDFAIL

LMP Neighbor Discovery has failed

Y

Y

LO-RXPOWER

Equipment Low Receive Power

Y

Y

LO-TXPOWER

Equipment Low Transmit Power

Y

Y

LOA

Loss of Alignment

Y

Y

LOC

Loss of Channel

Y

Y

LOCKOUT-REQ

Lockout Switch Request On Facility or Equipment

Y

Y

LOCKOUT-REQ-RING

Lockout Switch Request On Ring

Y

Y

LOCKOUTOFPR

Lockout Of Protection

Y

Y

LOF

Loss Of Frame

Y

Y

LOM

Loss of Multi-Frame

Y

Y

LOS

Loss Of Signal

Y

Y

LOS-CONT

Loss Of Continuity

Y

Y

LP-PLM

Signal Label Mismatch Failure (SLMF)—PLM Low Order—Path Label Mismatch

Y

Y

LP-RFI

RFI—Low Order—Remote Failure/Alarm Indication

Y

Y

LP-TIM

TIM Low Order—Trace Identifier Mismatch Failure

Y

Y

LP-UNEQ

Signal Label Mismatch Failure (SLMF)—Unequipped Low Order—Path Unequipped

Y

Y

LPBKCRS

Cross-connect Loopback

Y

Y

LPBKDS1FEAC

DS1 Loopback Due To Far End Alarm and Control (FEAC) Command

Y

Y

LPBKDS3FEAC

DS3 Loopback Due To FEAC Command

Y

Y

LPBKDS3FEAC-CMD

DS3 Loopback Command Sent To Far End

Y

Y

LPBKE1FEAC

E1 loopback due to FEAC command

Y

Y

LPBKE3FEAC

E3 loopback due to FEAC command

Y

Y

LPBKE3FEAC-CMD

E3 loopback command sent to far end

Y

Y

LPBKFACILITY

Facility Loopback

Y

Y

LPBKTERMINAL

Terminal Loopback

Y

Y

MAN-REQ

Manual Switch Request

Y

Y

MANRESET

Manual System Reset

Y

Y

MANSWTOINT

Manual Switch To Internal Clock

Y

Y

MANSWTOPRI

Manual Switch To Primary Reference

Y

Y

MANSWTOSEC

Manual Switch To Second Reference

Y

Y

MANSWTOTHIRD

Manual Switch To Third Reference

Y

Y

MANUAL-REQ-RING

Manual Switch Request On Ring

Y

Y

MANUAL-REQ-SPAN

Manual Switch Request On Span

Y

Y

MEA

Mismatch Of Equipment And Attributes

Y

Y

MEM-GONE

Free Memory On Card Near Zero

Y

Y

MEM-LOW

Free Memory On Card Very Low

Y

Y

MFGMEM

Manufacturing Data Memory (EEPROM Failure)

Y

Y

MS-AIS

AIS—Multiplex Section—Alarm Indication Signal

Y

Y

MS-EOC

Multiplex Section DCC Termination Failure

Y

Y

MS-RFI

RFI—Multiplex Section—Remote Failure/Alarm Indication

Y

Y

MSSP-OOSYNC

Procedural Error—MS-SPRing out of sync

Y

Y

NO-CONFIG

No Startup Configuration

Y

Y

NTWTPINC

Network Topology Incomplete

Y

Y

OCHNC-ACTIV-FAIL

Optical Channel Activation Failure

Y

Y

OCHNC-DEACTIV-FAIL

Optical Channel Deactivation Failure

Y

Y

OCHNC-FAIL

Optical Channel Connection Failure

Y

Y

OCHNC-INC

Optical Channel Incomplete

Y

Y

ODUK-AIS-PM

ODUk: Alarm Indication Signal

Y

Y

ODUK-BDI-PM

ODUk: PM Backward Defect Indication

Y

Y

ODUK-LCK-PM

ODUk: Locked Defect —Performance Monitoring (PM)

Y

Y

ODUK-OCI-PM

ODUk: Open Connection Indication

Y

Y

ODUK-SD-PM

ODUk: Signal Degrade

Y

Y

ODUK-SF-PM

ODUk: Signal Failure

Y

Y

ODUK-TIM-PM

ODUk: Trail Trace Identifier Mismatch

Y

Y

OOU-TPT

Out of Use—Transport Failure

Y

Y

OPTNTWMIS

Optical Network Type Mismatch

Y

Y

OPWR-HDEG

Optical Power Degrade High

Y

Y

OPWR-HFAIL

Optical Power Failure High

Y

Y

OPWR-LDEG

Optical Power Degrade Low

Y

Y

OPWR-LFAIL

Optical Power Failure Low

Y

Y

OTUK-AIS

OTUk: Alarm Indication Signal

Y

Y

OTUK-BDI

OTUk: Backward Defect Indication

Y

Y

OTUK-LOF

OTUk: Loss Of Frame

Y

Y

OTUK-SD

OTUk: Signal Degrade

Y

Y

OTUK-SF

OTUk: Signal Failure

Y

Y

OTUK-TIM

OTUk: Trail Trace Identifier Mismatch

Y

Y

OUT-OF-SYNC

8B10B Out of Sync

Y

Y

PDI-P

Payload Defect Indication—Path

Y

Y

PEER-NORESPONSE

Peer Card Not Responding

Y

Y

PORT-CODE-MISM

Pluggable port security code mismatch

Y

Y

PORT-COMM-FAIL

Module Communication Failure

Y

Y

PORT-MISMATCH

Pluggable port rate mismatch

Y

Y

PORT-MISSING

Pluggable port missing

Y

Y

PRC-DUPID

Duplicate Node ID

Y

Y

PROTNA

Protection Unit Not Available

Y

Y

PTIM

Payload Type Identifier Mismatch

Y

Y

PWR-REDUN

Redundant Power Capability Lost

Y

Y

RAI

Remote Alarm Indication

Y

Y

RCVR-MISS

Facility Termination Equipment—Receiver Missing

Y

Y

RFI

Remote Failure Indication

Y

Y

RFI-L

Remote Failure Indication—Line

Y

Y

RING-ID-MIS

Ring Id Mismatch

Y

Y

RING-MISMATCH

Far End Of Fiber Is Provisioned With Different Ring ID

Y

Y

RING-SW-EAST

Ring Switch Is Active On The East Side

Y

Y

RING-SW-WEST

Ring Switch Is Active On The West Side

Y

Y

RSVP-HELLODOWN

RSVP Hello FSM to Neighbor down

Y

Y

RUNCFG-SAVENEED

Need to Save Running Config

Y

Y

SD

Signal Degrade

Y

Y

SD-L

Bit Error Rate (BER) Threshold Exceeded For Signal Degrade—Line

Y

Y

SDBER-EXCEED-HO

BER Threshold Exceeded For Signal Degrade—High Order

Y

Y

SF

Signal Failure

Y

Y

SF-L

BER Threshold Exceeded For Signal Failure—Line

Y

Y

SFBER-EXCEED-HO

BER Threshold Exceeded For Signal Failure—High Order

Y

Y

SFTWDOWN

Software Download In Progress

Y

Y

SH-INS-LOSS-VAR-DEG-HIGH

Shutter Insertion Loss Variation Degrade High

Y

Y

SH-INS-LOSS-VAR-DEG-LOW

Shutter Insertion Loss Variation Degrade Low

Y

Y

SHUTTER-OPEN

Shutter Open

Y

Y

SNTP-HOST

Simple Network time Protocol (SNTP) Host Failure

Y

Y

SPAN-SW-EAST

Span Switch Is Active On The East Side

Y

Y

SPAN-SW-WEST

Span Switch Is Active On The West Side

Y

Y

SQM

Sequence Mismatch

Y

Y

SQUELCH

Ring Is Squelching Traffic

Y

Y

SQUELCH-PATH

Squelching Path

Y

Y

SQUELCHED

Equipment Squelched

Y

Y

SSM-DUS

Do Not Use For Synchronization

Y

Y

SSM-FAIL

Failed To Receive Synchronization Status Message

Y

Y

SSM-LNC

ITU-T G.812—Local Node Clock traceable

Y

Y

SSM-OFF

Synchronization Status Messages Are Disabled On This Interface

Y

Y

SSM-PRC

ITU-T G.811—Primary Reference Clock traceable

Y

Y

SSM-PRS

Stratum 1 Primary Reference Source Traceable

Y

Y

SSM-RES

Reserved For Network Synchronization Use

Y

Y

SSM-SDH-TN

ITU-T G.812—Transit Node Clock traceable

Y

Y

SSM-SETS

ITU-T G.813—Synchronous Equipment Timing Source traceable

Y

Y

SSM-SMC

SDH Minimum Clock Traceable

Y

Y

SSM-ST2

Stratum 2 Traceable

Y

Y

SSM-ST3

Stratum 3 Traceable

Y

Y

SSM-ST3E

Stratum 3E Traceable

Y

Y

SSM-ST4

Stratum 4 Traceable

Y

Y

SSM-STU

Synchronized—Traceability Unknown

Y

Y

SSM-TNC

Transit Node Clock Traceable

Y

Y

SWMTXMOD

Switching Matrix Module Failure

Y

Y

SWTOPRI

Switch To Primary Reference

Y

Y

SWTOSEC

Switch To Second Reference

Y

Y

SWTOTHIRD

Switch To Third Reference

Y

Y

SYNC-FREQ

Synchronization Reference Frequency Out Of Bounds

Y

Y

SYNCPRI

Primary Synchronization Reference Failure

Y

Y

SYNCSEC

Secondary Synchronization Reference Failure

Y

Y

SYNCTHIRD

Third Synchronization Reference Failure

Y

Y

SYSBOOT

System Reboot

Y

Y

TIM

TIM Section—Trace Identifier Mismatch Failure

Y

Y

TIM-MON

TIM Section Monitor—Trace Identifier Mismatch Failure

Y

Y

TPTFAIL

Transport layer failure

Y

Y

TRMT

Transmit Failure

Y

Y

TRMT-MISS

Facility Termination Equipment—Transmitter Missing

Y

Y

TU-AIS

AIS—Tributary Unit—Alarm Indication Signal

Y

Y

TU-LOP

LOP—Tributary Unit—Loss of Pointer

Y

Y

TUNDERRUN

Ethernet Transmit First In First Out Underrun

Y

Y

TX-AIS

Alarm Indication Signal in TX

Y

Y

TX-RAI

Remote Alarm Indication in TX

Y

Y

UNC-WORD

FEC Uncorrected Word

Y

Y

VCG-DEG

VCAT Group Degraded

Y

Y

VCG-DOWN

VCAT Group Down

Y

Y

VOA-HDEG

Variable Optical Attenuator Degrade High

Y

Y

VOA-HFAIL

Variable Optical Attenuator Failure High

Y

Y

VOA-LDEG

Variable Optical Attenuator Degrade Low

Y

Y

VOA-LFAIL

Variable Optical Attenuator Failure Low

Y

Y

WKSWPR

Switched To Protection

Y

Y

WTR

Wait To Restore

Y

Y

WVL-MISMATCH

Equipment Wavelength Mismatch

Y

Y