Cisco ONS 15454 DWDM Procedure Guide, Releases 9.2.1 and 9.2.2

Monitor Performance

---

This chapter explains how to enable and view performance monitoring (PM) statistics for the Cisco ONS 15454. PM parameters are used by service providers to gather, store, set thresholds, and report performance data for early detection of problems. For more PM information, details, and definitions, refer to the Cisco ONS 15454 DWDM Troubleshooting Guide.

Note The procedures and tasks described in this chapter for the Cisco ONS 15454 platform is applicable to the Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms, unless noted otherwise.

Note Unless otherwise specified, “ONS 15454” refers to both ANSI and ETSI shelf assemblies.

Before You Begin

Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide as necessary.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. NTP-G73 Change the PM Display—Complete as needed to change the displayed PM counts.

2. G279 Monitor TNC Card Performance—Complete as needed to monitor the performance for the TNC card.

3. G74 Monitor DWDM Card Performance—Complete as needed to monitor performance for dense wavelength division multiplexing (DWDM) cards, which includes the OSCM, OSC-CSM, 32MUX-O, 32DMX, 32DMX-O, 32DMX-L, 40-MUX-C, 40-DMX-C, 40-DMX-CE, 40-WSS-C, 40-WSS-CE, 40-WXC-C, 80-WXC-C, 40-SMR1-C, 40-SMR2-C, 4MD-xx.x, AD-xC-xx.x, AD-xB-xx.x, 32WSS, 32WSS-L, TDC-CC, TDC-FC. OPT-BST, OPT-PRE, OPT-BST-L, OPT-AMP-L, OPT-AMP-17-C, OPT-RAMP-C and OPT-RAMP-CE cards.

4. G75 Monitor Transponder and Muxponder Performance—Complete as needed to monitor performance for all transponder (TXP), muxponder (MXP), Xponder (GE_XP, 10GE_XP, GE_XPE, 10GE_XPE, and OTU2_XP), and ADM-10G cards.

5. G193 Enable or Disable AutoPM—Complete as needed to enable or disable automatic autonomous performance monitoring (AutoPM) reports.

Note For additional information regarding PM parameters, refer to Telcordia GR-499-CORE, GR-253-CORE, GR-820-CORE (titled Generic Digital Transmission Surveillance), and GR-1230-CORE, and to the ANSI T1.231 document titled Digital Hierarchy - Layer 1 In-Service Digital Transmission Performance Monitoring.

NTP-G73 Change the PM Display

Step 1 Complete the G46 Log into CTC at the node that you want to monitor. If you are already logged in, continue with Step 2.

Step 2 As needed, use the following tasks to change the display of PM counts:

• G131 Refresh PM Counts at 15-Minute Intervals
• G132 Refresh PM Counts at One-Day Intervals
• G133 View Near-End PM Counts
• G134 View Far-End PM Counts
• G135 Reset Current PM Counts
• G136 Clear Selected PM Counts
• G410 Clear All PM Thresholds
• G137 Set the Auto-Refresh Interval for Displayed PM Counts
• G138 Refresh PM Counts for a Different Port

Stop. You have completed this procedure.

DLP-G131 Refresh PM Counts at 15-Minute Intervals

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to change the PM count display interval. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to change the PM interval to 15 minutes for a subtab, click the relevant subtab(s), located on the left side of the Performance tab.

Note Performance subtabs vary depending on the card.

Step 4 If you want to change the PM interval to 15 minutes for a specific port, select the port from the Ports drop-down list (where available).

Step 5 To go to any of the tabs, subtabs, or ports (found in the Ports drop-down list where available) for the card where you want to set the PM count interval, click the subtab and choose the port, if applicable from the drop-down list.

Step 6 Click the 15 min radio button.

Step 7 Click Refresh. PM parameters appear in 15-minute intervals synchronized with the time of day.

Step 8 View the Curr column to find PM counts for the current 15-minute interval.

Each monitored performance parameter has corresponding threshold values for the current time period. If the value of the counter exceeds the threshold value for a particular 15-minute interval, a threshold crossing alert (TCA) is raised. The number represents the counter value for each specific PM parameter.

Step 9 View the Prev- n columns to find PM counts for the previous 15-minute intervals.

Note If a complete 15-minute interval count is not possible, the value appears with a yellow background. An incomplete or incorrect count can be caused by monitoring for less than 15 minutes after the counter started, changing the node timing settings, changing the time zone settings, replacing a card, resetting a card, or changing port service states. When the problem is corrected, the subsequent 15-minute interval appears with a white background.

Step 10 Return to your originating procedure (NTP).

DLP-G132 Refresh PM Counts at One-Day Intervals

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to change the PM interval. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to refresh the PM counts for a subtab, click the relevant subtab(s), located along the left side of the Performance tab.

Note Performance subtabs vary depending on the card.

Step 4 If you want to refresh the PM counts for a specific port, select the port from the Ports drop-down list (where available).

Step 5 Click the 1 day radio button.

Step 6 Click Refresh. Performance monitoring appears in 1-day intervals synchronized with the time of day.

Step 7 View the Curr column to find PM counts for the current 1-day interval.

Each monitored performance parameter has corresponding threshold values for the current time period. If the value of the counter exceeds the threshold value for a particular 1-day interval, a TCA is raised. The number represents the counter value for each specific PM parameter.

Step 8 View the Prev- n columns to find PM counts for the previous 1-day intervals.

Note If a complete count over a 1-day interval is not possible, the value appears with a yellow background. An incomplete or incorrect count can be caused by monitoring for less than 24 hours after the counter started, changing node timing settings, changing the time zone settings, replacing a card, resetting a card, or changing port service states. When the problem is corrected, the subsequent 1-day interval appears with a white background.

Step 9 Return to your originating procedure (NTP).

DLP-G133 View Near-End PM Counts

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to view near end PM counts. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to view the near-end PM counts for a subtab, click the relevant subtab(s), located on the left side of the Performance tab.

Note Performance subtabs vary depending on the card.

Step 4 If you want to view near-end PM counts for a specific port, select the port from the Ports drop-down list (where available).

Step 5 Click the Near End radio button, where available. (Viewing near-end PM counts is not available on some tabs.)

Step 6 Click Refresh. All current PM parameters for the selected card on the incoming signal appear. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 7 View the Curr column to find PM counts for the current time interval.

Step 8 View the Prev- n columns to find PM counts for the previous time intervals.

Step 9 Return to your originating procedure (NTP).

DLP-G134 View Far-End PM Counts

Note Far-end PM parameters are not available for all ports.

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to view far-end PM counts. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to view far-end PM counts for a subtab, click the relevant subtab(s), located along the left side of the Performance tab.

Note Performance subtabs vary depending on the card.

Step 4 If you want to view far-end PM counts for a specific port, select the port from the Ports drop-down list (where available).

Step 5 Click the Far End radio button, where available. (Viewing far-end PM counts is not available on some tabs.)

Step 6 Click Refresh. All PM parameters recorded by the far-end node for the selected card on the outgoing signal appear. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 7 View the Curr column to find PM counts for the current time interval.

Step 8 View the Prev- n columns to find PM counts for the previous time intervals.

Step 9 Return to your originating procedure (NTP).

DLP-G135 Reset Current PM Counts

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to reset the current PM counts. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to reset the PM counts for a subtab, click the relevant subtab(s), located along the left side of the Performance tab.

Note Performance subtabs vary depending on the card.

Step 4 If you want to reset the PM counts for a specific port, select the port from the Ports drop-down list (where available).

Note For all TXP and MXP cards and the GE_XP, 10GE_XP, GE_XPE, 10GE_XPE, ADM-10G, and OTU2_XP card, you cannot change the PM count interval on the Optics PM > Current Values tab.

Step 5 Click Baseline.

Note The Baseline button clears the PM counts that appear in the current time interval but does not clear the PM counts on the card. When the current time interval expires or the window view changes, the total number of PM counts on the card and in the window appears in the appropriate column. The baseline values are discarded if you change views to a different window and then return to the Performance window.

Step 6 View the current statistics columns to observe changes to PM counts for the current time interval.

Step 7 Return to your originating procedure (NTP).

DLP-G136 Clear Selected PM Counts

Caution Pressing the Clear button can mask problems if used incorrectly. This button is commonly used for testing purposes. After pressing this button, the current bin is marked invalid. Also note that the unavailable seconds (UAS) count is not cleared if you were counting UAS; therefore, this count could be unreliable when you press Clear.

---

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to clear the PM counts. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to clear the selected PM counts for a subtab, click the relevant subtab(s), located along the left side of the Performance tab and click Clear.

Note Performance subtabs vary depending on the card.

Step 4 If you want to clear the selected PM counts for a specific port, select the OTN subtab or port from the Ports drop-down list (where available).

Note For all TXP and MXP cards and the GE_XP, 10GE_XP, GE_XPE, 10GE_XPE, ADM-10G, and OTU2_XP card, you cannot change the PM count interval on the Optics PM > Current Values tab.

Step 5 Click Clear.

Step 6 From the Clear Statistics dialog box, click one of the following radio buttons:

• Displayed statistics : Clearing displayed statistics erases all PM counts associated with the current combination of statistics on the selected port from the card and the window. This means that the selected time interval, direction, and signal type counts are erased from the card and the window.
• All statistics for port x : Clearing all statistics for port x erases all PM counts associated with all combinations of the statistics on the selected port from the card and the window. This means that all time intervals, directions, and signal type counts are erased from the card and the window.
• All statistics for card : Clearing all statistics for card erases all PM counts for all ports from the card and the window.

Step 7 From the Clear Statistics dialog box, click OK to clear the selected statistics. Click Yes to confirm the change.

Step 8 Verify that the selected PM counts have been cleared.

Step 9 Return to your originating procedure (NTP).

DLP-G410 Clear All PM Thresholds

Caution Pressing the Reset button can mask problems if used incorrectly. This button is commonly used for testing purposes.

---

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the card where you want to view PM thresholds. The card view appears.

Step 2 Click the Provisioning tab.

Step 3 Click the Thresholds subtabs. The subtab names vary depending on the card selected.

Step 4 Click Reset to Default.

Step 5 Click Yes in the Reset to Default dialog box.

Step 6 Verify that the PM thresholds have been reset.

Step 7 Return to your originating procedure (NTP).

DLP-G137 Set the Auto-Refresh Interval for Displayed PM Counts

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the card where you want to set the auto-refresh interval for displayed PM counts. The card view appears.

Step 2 Click the Performance tab.

Step 3 If you want to set the PM auto-refresh interval for a subtab, click the relevant subtab(s), located along the left side of the Performance tab.

Note Performance subtabs vary depending on the card.

Step 4 If you want to set the PM auto-refresh interval for a specific port, select the port from the Ports drop-down list (where available).

Step 5 From the Auto-refresh drop-down list, choose one of the following options:

• None : This option disables the auto-refresh feature.
• 15 Seconds : This option sets the window auto-refresh at 15-second time intervals.
• 30 Seconds : This option sets the window auto-refresh at 30-second time intervals.
• 1 Minute : This option sets the window auto-refresh at 1-minute time intervals.
• 3 Minutes : This option sets the window auto-refresh at 3-minute time intervals.
• 5 Minutes : This option sets the window auto-refresh at 5-minute time intervals.

Step 6 Click Refresh. The PM counts for the newly selected auto-refresh time interval appear.

Depending on the selected auto-refresh interval, the displayed PM counts automatically update when each refresh interval completes. If the auto-refresh interval is set to None, the PM counts that appear are not updated unless you click Refresh.

Step 7 Return to your originating procedure (NTP).

DLP-G138 Refresh PM Counts for a Different Port

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the DWDM, TXP, or MXP card where you want to refresh PM counts for a different port. The card view appears.

Step 2 Click the Performance tab.

Step 3 In the Port drop-down list, choose a port.

Step 4 Click Refresh. The PM counts for the newly selected port appear.

Step 5 Return to your originating procedure (NTP).

NTP-G279 Monitor TNC Card Performance

Step 1 Complete the G46 Log into CTC at the node that you want to monitor performance. If you are already logged in, continue with Step 2.

Step 2 Complete the following tasks as needed:

• G607 View Optics PM Parameters for the TNC Card
• G608 View Payload PM Parameters for the TNC Card
• G686 Set the TNC Card RMON Thresholds for the FE/ONE_GE Ethernet Payloads

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Stop. You have completed this procedure.

DLP-G607 View Optics PM Parameters for the TNC Card

Note The optics PMs for data parameters can be viewed only after creating a pluggable port module (PPM). See the G128 Manage Pluggable Port Modules for more information about PPMs.

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the TNC card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Optics PM tabs.

Step 3 View the PM parameter names that appear in the Param column of the Current Values and Historical PM tabs. In the Historical PM tab, the PM parameter values appear in the Curr (current) and Prev- n (previous) columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 4 Return to your originating procedure (NTP).

DLP-G608 View Payload PM Parameters for the TNC Card

Note The payload PMs for data parameters can be viewed only after creating a pluggable port module (PPM). See the G128 Manage Pluggable Port Modules for more information about PPMs.

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the TNC card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Payload PM tabs.

Ethernet and SONET tabs appear depending on the PPMs and ports that you provisioned through the Provisioning tab.

Step 3 View the PM parameter names that appear in the Param column of the SONET tab. The PM parameter values appear in the Curr (or current), and Prev- n (previous) columns.

The Ethernet tab has three subtabs: Statistics, Utilization, and History. You can view the PM parameter names and current parameter values in the Statistics subtab. You can view the percentage of utilization of Tx and Rx ports in the Utilization subtab. You can view the PM parameter names and previous parameter values in the History subtab.

For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 4 Return to your originating procedure (NTP).

DLP-G686 Set the TNC Card RMON Thresholds for the FE/ONE_GE Ethernet Payloads

Note This task can only be performed if the TNC card has at least one PPM port provisioned for FE or ONE_GE payloads.

Step 1 In node view (single-shelf mode) or shelf view (multishelf view), display the TNC card where you want to set the RMON thresholds.

Step 2 Click the Provisioning > RMON Thresholds tabs.

Step 3 Click Create. The Create Threshold dialog box appears.

Step 4 From the Port drop-down list, choose an individual port (FE or ONE_GE), or choose All to provision RMON thresholds for all ports.

Step 5 From the Variable drop-down list, choose an Ethernet variable. See Table 9-1 for a list of available Ethernet RMON variables.

Table 9-1 TNC Card FE and ONE_GE RMON Thresholds

Step 6 From the Alarm Type drop-down list, indicate whether the event will be triggered by the rising threshold, the falling threshold, or both the rising and falling thresholds.

Step 7 From the Sample Type drop-down list, choose either Relative or Absolute. Relative restricts the threshold to use the number of occurrences in the user-set sample period. Absolute sets the threshold to use the total number of occurrences, regardless of time period.

Step 8 Enter the appropriate number of seconds for the Sample Period in the Sample Period field.

Step 9 Enter the appropriate number of occurrences for the Rising Threshold in the Rising Threshold field.

For a rising type of alarm, the measured value must move from below the falling threshold to above the rising threshold. For example, if a network is running below a rising threshold of 1000 collisions every 15 seconds and a problem causes 1001 collisions in 15 seconds, the excess occurrences trigger an alarm.

Step 10 Enter the appropriate number of occurrences in the Falling Threshold field. In most cases a falling threshold is set lower than the rising threshold.

A falling threshold is the counterpart to a rising threshold. When the number of occurrences is above the rising threshold and then drops below a falling threshold, it resets the rising threshold. For example, when the network problem that caused 1001 collisions in 15 seconds subsides and creates only 799 collisions in 15 seconds, occurrences fall below a falling threshold of 800 collisions. This resets the rising threshold so that if network collisions again spike over a 1000 per 15-second period, an event again triggers when the rising threshold is crossed. An event is triggered only the first time a rising threshold is exceeded (otherwise, a single network problem might cause a rising threshold to be exceeded multiple times and cause a flood of events).

Step 11 Click OK.

Step 12 To view all the RMON thresholds, click Show All RMON thresholds.

Step 13 Return to your originating procedure (NTP).

NTP-G74 Monitor DWDM Card Performance

Step 1 Complete the G46 Log into CTC at the node that you want to monitor. If you are already logged in, continue with Step 2.

Step 2 Complete the following tasks as needed:

• G139 View PM Parameters for OSCM and OSC-CSM cards.
• G140 View Power Statistics for Optical Amplifier, 40-SMR1-C, and 40-SMR2-C Cards.
• G141 View Optical Power Statistics for 32MUX-O, 32WSS, 32WSS-L, 32DMX-O, 32DMX, 32DMX-L, 40-WSS-C, 40-WSS-CE, 40-WXC-C, 80-WXC-C, 40-MUX-C, 40-DMX-C, and 40-DMX-CE Cards.
• G479 View Optical Power Statistics for the PSM Card
• G276 View Optical Power Statistics for 4MD-xx.x Cards
• G142 View Power Statistics for AD-1C-xx.x, AD-2C-xx.x, and AD-4C-xx.x Cards.
• G143 View Power Statistics for AD-1B-xx.x and AD-4B-xx.x Cards.
• “G525 View Optical Power Statistics for TDC-CC and TDC-FC cards” section
• G475 View the PM Parameters for All Facilities

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Stop. You have completed this procedure.

DLP-G139 View PM Parameters for OSCM and OSC-CSM cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the OSCM or OSC-CSM card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > OC3 Line tabs.

Step 3 Click Refresh. PMs appear for the OC3 (Port 1).

Step 4 Click the Optical Line tab.

Step 5 In the Port drop-down list, choose the optical line port where you want to view the power statistics:

• 2—COM RX
• 3—COM TX
• 4—LINE RX (available only on the OSC-CSM card)
• 5—LINE TX (available only on the OSC-CSM card)
• 6—OSC RX (available only on the OSC-CSM card)
• 7—OSC TX (available only on the OSC-CSM card)

Step 6 Click Refresh. The minimum, maximum, and average optical power statistics for the selected line port appear.

Step 7 Return to your originating procedure (NTP).

DLP-G140 View Power Statistics for Optical Amplifier, 40-SMR1-C, and 40-SMR2-C Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Optical Line tab.

Step 3 In the Port drop-down list, choose an optical line port where you want to view the optical power statistics:

• For the OPT-PRE card, the following ports are available to view:

– 1—COM RX

– 3—DC RX

– 4—DC TX

• For the OPT-BST and OPT-BST-E cards, the following ports are available to view:

– 1—COM RX

– 2—COM TX

– 4—OSC TX

• For the OPT-BST-L card, the following ports are available to view:

– 1—COM RX

– 2—COM TX

– 4—OSC TX

• For the OPT-AMP-L card, the following ports are available to view:

– 1—COM RX

– 2—COM TX

– 4—OSC TX

– 7—DC RX

– 8—DC TX

• For the OPT-AMP-17-C card, the following ports are available to view:

– 1—COM RX

– 2—COM TX

– 3—COM RX

– 4—OSC TX

• For the OPT-RAMP-C card, the following ports are available to view:

– 1—COM RX

– 2—COM TX

– 3—OSC RX

– 4—OSC TX

– 5—LINE-RX

– 6—LINE-TX

– 7—DC-RX

– 9—RAMAN RX

– 10—RAMAN TX

• For the OPT-RAMP-CE card, the following ports are available to view:

– 1—COM RX

– 2—COM TX

– 3—OSC RX

– 4—OSC TX

– 5—LINE-RX

– 6—LINE-TX

– 7—DC-RX

– 9—RAMAN RX

– 10—RAMAN TX

• For the 40-SMR1-C card, the following ports are available to view:

– 1—EXP-RX

– 3—DC-RX

– 4—DC-TX

– 5—OSC-RX

– 6—OSC-TX

– 7—ADD-RX

– 8—DROP-TX

– 9—LINE-RX

– 10—LINE-TX

• For the 40-SMR2-C card, the following ports are available to view:

– 1—DC-RX

– 2—DC-TX

– 3—OSC-RX

– 4—OSC-TX

– 5—ADD-RX

– 6—DROP-TX

– 7—LINE-RX

– 10—EXP-RX 1-2

– 11—EXP-RX 1-3

– 12—EXP-RX 1-4

Step 4 Click Refresh. Optical power statistics for the selected port appear.

Step 5 Click the Opt. Ampli. Line tab.

Step 6 Click Refresh. Optical power statistics for the optical amplifier output port appear:

• 2 (COM-TX), OPT-PRE card
• 6 (LINE-TX), OPT-BST card
• 6 (LINE-TX), OPT-AMP-17-C card
• 8 (DC-TX), OPT-RAMP-C card
• 8 (DC-TX), OPT-RAMP-CE card
• 2 (EXP-TX), 40-SMR1-C card
• 8 (LINE-TX), 9 (EXP-TX 1-1), 40-SMR2-C card

Step 7 Click the OCH tab. In the Port drop-down list, choose an OCH port where you want to view the optical power statistics:

• For the 40-SMR1-C card, the following ports are available to view:

– 1—EXP-RX

– 2—EXP-TX

– 7—ADD-RX

– 8—DROP-TX

– 10—LINE-TX

• For the 40-SMR2-C card, the following ports are available to view:

– 5—ADD-RX

– 6—DROP-TX

– 8—LINE-TX

– 9—EXP-TX 1-1

– 10—EXP-RX 1-2

– 11—EXP-RX 1-3

– 12—EXP-RX 1-4

Step 8 Click Refresh. The OCH power statistics (minimum, maximum, average) for the selected port appear.

Note For the 40-SMR1-C and 40-SMR1-C cards, the OCH power statistics are reported only for those ports that are part of a circuit.

Step 9 Click the Opt. Raman. Line tab. Optical power statistics for the optical amplifier output port appear:

• 10 (RAMAN-TX), OPT-RAMP-C card
• 10 (RAMAN-TX), OPT-RAMP-CE card

Step 10 Return to your originating procedure (NTP).

DLP-G141 View Optical Power Statistics for 32MUX-O, 32WSS, 32WSS-L, 32DMX-O, 32DMX, 32DMX-L, 40-WSS-C, 40-WSS-CE, 40-WXC-C, 80-WXC-C, 40-MUX-C, 40-DMX-C, and 40-DMX-CE Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Optical Chn tabs.

Step 3 In the Port drop-down list, select the port where you want to view the optical power statistics.

• 32MUX-O—optical channel receive port (CHAN RX), Ports 01 through 32.
• 40-MUX-C—optical channel receive port (CHAN RX), Ports 01 through 40.
• 32WSS and 32WSS-L—optical channel receive port (ADD RX) Ports 01 through 32, or a pass-through port (PT), Ports 33 through 64.
• 32DMX-O, 32DMX, and 32DMX-L—optical channel transmit port (CHAN TX), Ports 01 through 32.
• 40-DMX-C/40-DMX-CE—optical channel transmit port (CHAN TX), Ports 01 through 40.
• 40-WSS-C/40-WSS-CE—optical add receive port (ADD RX), Ports 01 through 40, or a pass-through port (PT), Ports 41 through 80.

Step 4 Click Refresh. Optical channel power statistics (minimum, maximum, average) for the selected port appear.

Step 5 Click the Optical Line tab.

Step 6 Select the port where you want to view the optical power statistics, in the Port drop-down list.

• 32WSS and 32WSS-L - Port 65, 66, 67, 68 or 69.
• 32DMX-L or 32DMX-O - accept the default port (33)
• 40-WXC-C and 40-WXC-CE - Port 10, 11, 12, or 13.
• 80-WXC-C - Ports 1 through 13 (BIDIRECTIONAL mode), ports 1 through 10 (MULTIPLEXER or DEMULTIPLEXER mode).
• 40-WSS-C and 40-WSS-CE - Port 81, 82, 83, 84, or 85.
• 40-DMX-C and 40-DMX-CE - accept the default port (41).

Step 7 Click Refresh. Optical channel power statistics (minimum, maximum, average) for the selected port appear.

Step 8 Return to your originating procedure (NTP).

Note To view the Optical Side graphs of DWDM cards, see the section “Power Side Monitoring” in the chapter, Network Reference in the Cisco ONS 15454 DWDM Reference Manual, Release 9.2.

DLP-G479 View Optical Power Statistics for the PSM Card

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the PSM card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Optical Line tabs.

Step 3 In the Port drop-down list, select the port where you want to view the optical power statistics.

• 1—W RX
• 2—W TX
• 3—P RX
• 4—P TX
• 5—COM RX
• 6—COM TX

Step 4 Click Refresh. Optical channel power statistics (minimum, maximum, average) for the selected port appear.

Step 5 To change the auto-refresh interval, click Auto Refresh and choose one of the automatic refresh intervals: None, 15 seconds, 30 seconds, 1 minute, 3 minutes, or 5 minutes.

Step 6 Return to your originating procedure (NTP).

DLP-G276 View Optical Power Statistics for 4MD-xx.x Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the 4MD-xx.x card where you want to view the optical power statistics. The card view appears.

Step 2 Click the Performance > Optical Chn tabs.

Step 3 In the Port drop-down list, choose the channel port where you want to view the power statistics (port 1 through 8 for CHAN Ports 01 through 08).

Step 4 Click Refresh. The minimum, maximum, and average optical power for the selected channel port appear.

Step 5 To change the auto-refresh interval, click Auto Refresh and choose one of the automatic refresh intervals: None, 15 seconds, 30 seconds, 1 minute, 3 minutes, or 5 minutes.

Step 6 Click the Optical Band tab.

Step 7 In the Port drop-down list, choose the band port where you want to view the power statistics (band port 9 or 10 for COM Ports 09 and 10).

Step 8 Click Refresh. The minimum, maximum, and average optical power for the selected band port appear.

Step 9 To change the auto-refresh interval, click Auto Refresh and choose one of the automatic refresh intervals: None, 15 seconds, 30 seconds, 1 minute, 3 minutes, or 5 minutes.

Step 10 Return to your originating procedure (NTP).

DLP-G142 View Power Statistics for AD-1C-xx.x, AD-2C-xx.x, and AD-4C-xx.x Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the optical AD-xC-xx.x card where you want to view the optical power statistics. The card view appears.

Step 2 Click the Performance > Optical Line tabs.

Step 3 In the Port drop-down list, choose an optical line port ( Table 9-2 ) where you want to view the optical power statistics.

Step 4 Click Refresh. Optical line power statistics for the selected port appear.

Step 5 Click the Optical Chn tab.

Step 6 In the Port drop-down list, choose an optical channel port ( Table 9-3 ) where you want to view the optical power statistics.

Step 7 Click Refresh. Optical channel PM statistics for the selected port appear.

Step 8 Return to your originating procedure (NTP).

DLP-G143 View Power Statistics for AD-1B-xx.x and AD-4B-xx.x Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the optical AD-xB-xx.x card where you want to view the optical power statistics. The card view appears.

Step 2 Click the Performance > Optical Line tabs.

Step 3 In the Port drop-down list, choose an optical line port ( Table 9-4 ) where you want to view the optical power statistics.

Step 4 Click Refresh. Optical line power statistics for the selected port appear.

Step 5 Click the Optical Band tab.

Step 6 In the Port drop-down list, choose an optical band port ( Table 9-5 ) where you want to view the optical power statistics.

Step 7 Click Refresh. Optical channel PM statistics for the selected port appear.

Step 8 Return to your originating procedure (NTP).

DLP-G525 View Optical Power Statistics for TDC-CC and TDC-FC cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the TDC-CC or TDC-FC card where you want to view PM counts. The card view appears.

Step 2 Click the Optical Line tab.

Step 3 Select the port where you want to view the optical power statistics, in the Port drop-down list.

Step 4 Click Refresh. Optical channel power statistics (minimum, maximum, average) for the selected port appear.

Step 5 Return to your originating procedure (NTP).

DLP-G475 View the PM Parameters for All Facilities

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), click Maintenance > DWDM > All Facilities tabs.

Step 2 View the admin states, service states and power levels for all the facilities.

Step 3 Use the Mark button to selectively mark or unmark facilities. The marked facilities can be sorted on the Marked column. Sorting helps to group all the marked facilities in the table.

Step 4 Return to your originating procedure (NTP).

NTP-G75 Monitor Transponder and Muxponder Performance

Step 1 Complete the G46 Log into CTC at the node that you want to monitor. If you are already logged in, continue with Step 2.

Note To view optical transport network (OTN) PMs, the OTN parameters must be enabled. For more information, see Chapter6, “Provision Transponder and Muxponder Cards”

Step 2 Complete the following tasks as needed to view PM parameters:

• G390 View Ethernet Statistic PM Parameters for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards
• G391 View Ethernet Utilization PM Parameters for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards
• G392 View Ethernet History PM Parameters for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards
• G393 Refresh Ethernet PM Counts at a Different Time Interval for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards
• G146 View Optics PM Parameters
• G147 View Payload PM Parameters
• G148 View OTN PM Parameters
• G149 View Payload Statistics PM Parameters
• G150 View Payload Utilization PM Parameters
• G151 View Payload History PM Parameters
• G152 View Payload SONET/SDH PM Parameters

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Stop. You have completed this procedure.

DLP-G390 View Ethernet Statistic PM Parameters for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE card where you want to view the Ethernet statistics. The card view appears.

Step 2 Click the Performance > Ether Ports > Statistics tabs.

Step 3 Click Refresh. Performance monitoring statistics for each port on the card appear.

Step 4 View the PM parameter names appear in the Param column. The current PM parameter values appear in the Port # columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 5 Return to your originating procedure (NTP).

DLP-G391 View Ethernet Utilization PM Parameters for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards

Step 1 In node view, double-click the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE card where you want to view the Ethernet utilization. The card view appears.

Step 2 Click the Performance > Ether Ports > Utilization tabs.

Step 3 Click Refresh. The utilization percentages for each port on the card appear.

Step 4 View the Port # column to find the port you want to monitor.

The transmit (Tx) and receive (Rx) bandwidth utilization values for the previous time intervals appear in the Prev- n columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 5 Return to your originating procedure (NTP).

DLP-G392 View Ethernet History PM Parameters for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE card where you want to view the Ethernet history PM data. The card view appears.

Step 2 Click the Performance > Ether Ports > History tabs.

Step 3 Click Refresh. Performance monitoring statistics for each port on the card appear.

Step 4 View the PM parameter names that appear in the Param column. The PM parameter values appear in the Prev- n columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 5 Return to your originating procedure (NTP).

DLP-G393 Refresh Ethernet PM Counts at a Different Time Interval for GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE card where you want to view PM counts. The card view appears.

Step 2 Click the Performance tab.

Step 3 Click the Ether Ports > Utilization or the Ether Ports > History tabs.

Step 4 From the Interval drop-down list, choose one of four options:

• 1 min : This option shows the specified PM counts in one-minute time intervals.
• 15 min : This option shows the specified PM counts in 15-minute time intervals.
• 1 hour : This option shows the specified PM counts in one-hour time intervals.
• 1 day : This option shows the specified PM counts in one-day (24 hours) time intervals.

Step 5 Click Refresh. The PM counts refresh with values based on the selected time interval.

Step 6 Return to your originating procedure (NTP).

DLP-G146 View Optics PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the transponder or muxponder card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Optics PM > Historical PM tabs.

Step 3 View the PM parameter names that appear in the Param column of the Current Values and History PM tabs. The PM parameter values appear in the Curr (current) and Prev- n (previous) columns. For PM parameter definitions, see the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 4 Return to your originating procedure (NTP).

DLP-G147 View Payload PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the transponder or muxponder card where you want to view the payload PM counts. The card view appears.

Step 2 Click the Performance > Payload PM tabs.

Step 3 Go to any of the tabs, subtabs, or ports (found in the Ports drop-down list where available) for the card where you want to view the payload PM parameters by clicking on the desired subtab, and choosing the port from the Port drop-down list.

Step 4 View the PM parameter names that appear in the Param column of the SONET (or SDH), Utilization, Statistics, and History tabs. The PM parameter values appear in the Curr (or current), and Prev- n (previous) columns. For PM parameter definitions, see the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note The payload PMs for data parameters can be viewed only after creating a pluggable port module (PPM). For more information about PPMs, see the G128 Manage Pluggable Port Modules.

Note The PM parameters that appear depend on the data payload and framing type provisioned on the port. Unframed data payloads such as Enterprise System Connection (ESCON), DV6000, DSI/D1 video, and high-definition television (HDTV) do not provide payload PM information. The PM parameters that appear also depend on the PPM payload configured. The TXP_MR_10E card supports OC-192/STM-64, 10GE, and 10G FC payloads; the MXP_2.5G_10G and MXP_2.5G_10E cards support the OC48/STM16 payload; the MXP_MR_2.5G and MXPP_MR_2.5G cards support the 1G FC, 2G FC, 1G FICON, 2G FICON, and 1GE payloads; the ADM-10G card supports the OC-3/STM-1, OC-12/STM-4, OC-48/STM-16, 1GIGE payloads on client ports and the OC-192/STM-64 payloads on trunk ports; the OTU2_XP card supports the OC-192/STM-64, 10GE, and 10G FC payloads.

Step 5 Return to your originating procedure (NTP).

DLP-G148 View OTN PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the TXP or MXP card where you want to view OTN PM parameters. The card view appears.

Step 2 Click the Performance > OTN PM > ITU-T G.709 PM tabs.

Step 3 View the PM parameter names that appear in the Param column. The PM parameter values appear in the Curr (current) and Prev- n (previous) columns. For PM parameter definitions, see the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 4 Click the FEC PM tab.

Step 5 View the PM parameter names that appear in the Param column. The PM parameter values appear in the Curr (current) and Prev- n (previous) columns. For PM parameter definitions, see the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Step 6 Return to your originating procedure (NTP).

DLP-G149 View Payload Statistics PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the MXP_MR_2.5G or MXPP_MR_2.5G card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Payload PM > Statistics tabs.

Step 3 Click Refresh. PM statistics appear for each port on the card.

Step 4 View the PM parameter names that appear in the Param column. The current PM parameter values appear in the Port # columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 5 Return to your originating procedure (NTP).

DLP-G150 View Payload Utilization PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the MXP_MR_2.5G or MXPP_MR_2.5G card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Payload PM > Utilization tabs.

Step 3 Click Refresh. PM utilization values appear for each port on the card.

Step 4 View the appropriate row for the port you want to monitor.

Step 5 The transmit (Tx) and receive (Rx) bandwidth utilization values for the previous time intervals appear in the Prev- n columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 6 Return to your originating procedure (NTP).

DLP-G151 View Payload History PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the MXP_MR_2.5G or MXPP_MR_2.5G card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Payload PM > History tabs.

Step 3 Select the desired port from the Port drop-down list.

Step 4 Click Refresh. PM statistics appear for the selected port.

Step 5 View the PM parameter names that appear in the Param column. The PM parameter values appear in the Prev- n columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 6 Return to your originating procedure (NTP).

DLP-G152 View Payload SONET/SDH PM Parameters

Step 1 In node view (single-shelf mode), or shelf view (multishelf mode), double-click the MXP_MR_2.5G or MXPP_MR_2.5G card where you want to view PM counts. The card view appears.

Step 2 Click the Performance > Payload PM > SONET or SDH tabs.

Step 3 Click Refresh. PM statistics appear for the selected port.

Step 4 View the PM parameter names that appear in the Param column. The PM parameter values appear in the Prev- n columns. For PM parameter definitions, refer to the “Performance Monitoring” chapter in the Cisco ONS 15454 DWDM Reference Manual.

Note The MXP_MR_2.5G and MXPP_MR_2.5G cards support only the OC48/STM16 payload. Each payload has a set of PM parameters.

Note To refresh, reset, or clear PM counts, see the G73 Change the PM Display.

Step 5 Return to your originating procedure (NTP).

NTP-G193 Enable or Disable AutoPM

Step 1 Complete the G46 Log into CTC. If you are already logged in, continue with Step 2.

Step 2 Click the Provisioning > Defaults tabs.

Step 3 In the Defaults Selector area, click NODE > General and choose NODE.general.AutoPM.

Step 4 In the Default Value field, select True to enable AutoPM.

Step 5 Click Apply.

Step 6 Follow Steps 1 through 5 to disable AutoPM. Select False in the Default Value field in Step 4 before proceeding to Step 5.

Stop. You have completed this procedure.