Cisco ONS SDH TL1 Command Guide, Release 9.0
Chap 11: ED Commands
Downloads: This chapterpdf (PDF - 2.39MB) The complete bookPDF (PDF - 18.75MB) | Feedback

ED Commands

Table Of Contents

ED Commands

11.1  ED-<GIGE_TYPE>

11.2  ED-<MOD1FCPAYLOAD>

11.3  ED-<MOD1FICONPAYLOAD>

11.4  ED-<MOD2DWDMPAYLOAD>

11.5  ED-<MOD_PATH>

11.6  ED-<MOD_RING>

11.7  ED-<STM_TYPE>

11.8  ED-ALS

11.9  ED-APC

11.10  ED-BITS

11.11  ED-BULKROLL-<STM_TYPE>

11.12  ED-BWP-ETH

11.13  ED-CMD-SECU

11.14  ED-COS-ETH

11.15  ED-CRS-<PATH>

11.16  ED-CRS-ETH

11.17  ED-DAT

11.18  ED-DS3I

11.19  ED-E1

11.20  ED-E3

11.21  ED-E4

11.22  ED-ETH

11.23  ED-EQPT

11.24  ED-FAC

11.25  ED-FFP-<MOD2DWDMPAYLOAD>

11.26  ED-FFP-<STM_TYPE>

11.27  ED-FFP-OCH

11.28  ED-FFP-OTS

11.29  ED-FSTE

11.30  ED-FTPSERVER

11.31  ED-G1000

11.32  ED-GFP

11.33  ED-HDLC

11.34  ED-L2-ETH

11.35  ED-LMP

11.36  ED-LMP-CTRL

11.37  ED-LMP-TLINK

11.38  ED-LMP-DLINK

11.39  ED-LNK

11.40  ED-LNKTERM

11.41  ED-MCAST

11.42  ED-NE-GEN

11.43  ED-NE-PATH

11.44  ED-NE-SYNCN

11.45  ED-OCH

11.46  ED-OCHCC

11.47  ED-OCHNC

11.48  ED-OMS

11.49  ED-OTS

11.50  ED-PID

11.51  ED-POS

11.52  ED-PROTOCOL

11.53  ED-QNQ-ETH

11.54  ED-ROLL-<MOD_PATH>

11.55  ED-SLV-WDMANS

11.56  ED-STM1E

11.57  ED-SYNCN

11.58  ED-TRAPTABLE

11.59  ED-TRC-OCH

11.60  ED-T3

11.61  ED-USER-SECU

11.62  ED-VCG

11.63  ED-VLAN

11.64  ED-VLAN-ETH

11.65  ED-WDMANS

11.66  ED-WDMSIDE


ED Commands


This chapter provides edit (ED) commands for the Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH.

11.1  ED-<GIGE_TYPE>

(Cisco ONS 15454 SDH and Cisco ONS 15600 SDH) The Edit 10GIGE or GIGE (ED-<GIGE_TYPE>) command edits Ethernet facility attributes. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are network element (NE) default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

The user can change the service state of a facility to locked-enabled or disabled, only if all the following conditions are met

The facility is not sourcing a synchronization clock

The facility's DCC is disabled.

The facility is not part of a protection group

The facility is not supporting cross-connects


Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service with no consideration for orderly interruption. Do not use in scripts or automated batch operations.



Note To completely disable the CMDMDE=FRCD option, provision the <to be defined parameter> in the NE defaults to FALSE. This will prevent the FRCD option from being honored by the NE. The NE default parameter can be provisioned using the CTC only.



Note The following parameters apply only to ED-GIGE; ADMINSTATE, LINKSTATE, MTU, FLOWCTRL, AUTONEG, HIWMRK, LOWMRK, DUPLEX, SPEED, and SOAK.



Note The MACADDR parameter is applicable for ED-10GIGE only.



Note The LIENABLE and LITIMER parameters are applicable only to CE-1000 card.


Category

Ports

Security

Provisioning

Input Format

ED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[ADMINSTATE=<ADMINSTATE>],[LINKSTATE=<LINKSTATE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>],[AUTONEG=<AUTONEG>],[HIWMRK=<HIWMRK>],[LOWMRK=<LOWMRK>],[OPTICS=<OPTICS>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>],[NAME=<NAME>],[CMDMDE=<CMDMDE>],[MACADDR=<MACADDR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],[SOAK=<SOAK>],[LIENABLE=<LIENABLE>],[LITIMER=<LITIMER>]:[<PST>[,<SST>]];

Input Example

ED-GIGE:CISCO:FAC-1-1:123:::ADMINSTATE=DOWN,LINKSTATE=DOWN,MTU=1548,
FLOWCTRL=NONE,AUTONEG=Y,HIWMRK=485,LOWMRK=25,OPTICS=1000_BASE_LX,
DUPLEX=AUTO,SPEED=AUTO,NAME="GIGE PORT",CMDMDE=FRCD,
MACADDR=00-0E-AA-BB-CC-FF,FREQ=1550,LOSSB=SX,SOAK=32,LIENABLE=Y,
LITIMER=300:UNLOCKED,AUTOMATICINSERVICE;

Table 11-1 ED-<GIGE_TYPE> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the FACILITY.

Y

Y

N/A

<ADMINSTATE>

(Optional) The parameter type is UP_DOWN, which indicates an up or down value.

Y

Y

N/A

DOWN

Down

Y

Y

N/A

UP

Up

Y

Y

N/A

<LINKSTATE>

(Optional) The parameter type is UP_DOWN, which indicates an up or down value.

Y

Y

N/A

DOWN

Down

Y

Y

N/A

UP

Up

Y

Y

N/A

<MTU>

(Optional) Maximum transport unit. The parameter type is MTU_TYPE, which indicates the maximum transport unit used by an Ethernet card. Defaults to 9600.

Y

Y

N/A

10004

10004. Indicates jumbo size.

Y

Y

N/A

1500

1500

Y

Y

N/A

1548

1548

Y

Y

N/A

9600

9600. Indicates jumbo size.

Y

Y

N/A

64

64

Y

Y

N/A

9700

9700. Indicates jumbo size.

Y

Y

N/A

<FLOWCTRL>

(Optional) Flow control. The parameter type is FLOW, which indicates the type of flow control that has been negotiated for an Ethernet port. Defaults to NONE.

Y

Y

N/A

ASYMMETRIC

Asymmetric flow control

Y

Y

N/A

ASYMMETRIC_LOCAL

Asymmetric local flow control

Y

Y

N/A

NONE

No flow control

Y

Y

N/A

PASSTHRU

Passthrough flow control

Y

Y

N/A

SYMMETRIC

Symmetric flow control

Y

Y

N/A

<AUTONEG>

(Optional) Autonegotiation. The parameter is ON_OFF, which disables or enables an attribute. Defaults to Y.

Y

Y

N/A

N

Disable an attribute.

Y

Y

N/A

Y

Enable an attribute.

Y

Y

N/A

<HIWMRK>

(Optional) High water mark. HIWMRK is an integer. Defaults to 485.

Y

Y

N/A

<LOWMRK>

(Optional) Low water mark. LOWMRK is an integer. Defaults to 25.

Y

Y

N/A

<OPTICS>

(Optional) The parameter is OPTICS, which indicates the type of Gigabyte Ethernet optics being used.

Y

Y

N/A

1000_BASE_CX

1000BaseCX

Y

Y

N/A

1000_BASE_LX

1000BaseLX

Y

Y

N/A

1000_BASE_SX

1000BaseSX

Y

Y

N/A

1000_BASE_T

1000BaseT

Y

Y

N/A

1000_BASE_ZX

1000BaseZX

Y

Y

N/A

100_BASE_BX_D

100BaseBX_D

Y

Y

N/A

100_BASE_BX_U

100BaseBX_U

Y

Y

N/A

100_BASE_FX

100BaseFX

Y

Y

N/A

100_BASE_LX

100BaseLX

Y

Y

N/A

CWDM_1470

Coarse wavelength division multiplexing (CWDM) 1470

Y

Y

N/A

CWDM_1490

CWDM 1490

Y

Y

N/A

CWDM_1510

CWDM 1510

Y

Y

N/A

CWDM_1530

CWDM 1530

Y

Y

N/A

CWDM_1550

CWDM 1550

Y

Y

N/A

CWDM_1570

CWDM 1570

Y

Y

N/A

CWDM_1590

CWDM 1590

Y

Y

N/A

CWDM_1610

CWDM 1610

Y

Y

N/A

ITU_100G_1530_33

ITU-100G 1530.33

Y

Y

N/A

ITU_100G_1531_12

ITU-100G 1531.12

Y

Y

N/A

ITU_100G_1531_90

ITU-100G 1531.90

Y

Y

N/A

ITU_100G_1532_68

ITU-100G 1532.68

Y

Y

N/A

ITU_100G_1534_25

ITU-100G 1534.25

Y

Y

N/A

ITU_100G_1535_04

ITU-100G 1535.04

Y

Y

N/A

ITU_100G_1535_82

ITU-100G 1535.82

Y

Y

N/A

ITU_100G_1536_61

ITU-100G 1536.61

Y

Y

N/A

ITU_100G_1538_19

ITU-100G 1538.19

Y

Y

N/A

ITU_100G_1538_98

ITU-100G 1538.98

Y

Y

N/A

ITU_100G_1539_77

ITU-100G 1539.77

Y

Y

N/A

ITU_100G_1540_56

ITU-100G 1540.56

Y

Y

N/A

ITU_100G_1542_14

ITU-100G 1542.14

Y

Y

N/A

ITU_100G_1542_94

ITU-100G 1542.94

Y

Y

N/A

ITU_100G_1543_73

ITU-100G 1543.73

Y

Y

N/A

ITU_100G_1544_53

ITU-100G 1544.53

Y

Y

N/A

ITU_100G_1546_12

ITU-100G 1546.12

Y

Y

N/A

ITU_100G_1546_92

ITU-100G 1546.92

Y

Y

N/A

ITU_100G_1547_72

ITU-100G 1547.72

Y

Y

N/A

ITU_100G_1548_51

ITU-100G 1548.51

Y

Y

N/A

ITU_100G_1550_12

ITU-100G 1550.12

Y

Y

N/A

ITU_100G_1550_92

ITU-100G 1550.92

Y

Y

N/A

ITU_100G_1551_72

ITU-100G 1551.72

Y

Y

N/A

ITU_100G_1552_52

ITU-100G 1552.52

Y

Y

N/A

ITU_100G_1554_13

ITU-100G 1554.13

Y

Y

N/A

ITU_100G_1554_94

ITU-100G 1554.94

Y

Y

N/A

ITU_100G_1555_75

ITU-100G 1555.75

Y

Y

N/A

ITU_100G_1556_55

ITU-100G 156.55

Y

Y

N/A

ITU_100G_1558_17

ITU-100G 1558.17

Y

Y

N/A

ITU_100G_1558_98

ITU-100G 1558.98

Y

Y

N/A

ITU_100G_1559_79

ITU-100G 1559.79

Y

Y

N/A

ITU_100G_1560_61

ITU-100G 1560.61

Y

Y

N/A

UNKNOWN

Unknown

Y

Y

N/A

UNPLUGGED

Unplugged

Y

Y

N/A

<DUPLEX>

(Optional) The parameter is ETHER_DUPLEX, which indicates duplex mode. Defaults to AUTO.

Y

Y

N/A

AUTO

Auto mode

Y

Y

N/A

FULL

Full mode

Y

Y

N/A

HALF

Half mode

Y

Y

N/A

<SPEED>

(Optional) The parameter type is ETHER_SPEED, which indicates Ethernet speed. Defaults to AUTO.

Y

Y

N/A

100_MBPS

100 Megabits per second

Y

Y

N/A

10_GBPS

10 Gigabits per second

Y

Y

N/A

10_MBPS

10 Megabits per second

Y

Y

N/A

1_GBPS

1 Gigabit per second

Y

Y

N/A

AUTO

Automatic

Y

Y

N/A

<NAME>

(Optional) Port name. NAME is a string. Defaults to NULL. Maximum length is 32 characters.

Y

Y

N/A

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

Y

N/A

FRCD

Force the system to override a state where the command would normally be denied.

Y

Y

N/A

NORM

Execute the command normally. Do not override any conditions that might make the command fail.

Y

Y

N/A

<MACADDR>

(Optional) MACADDR is a string. Defaults to NULL. Maximum length is 18 characters.

Y

Y

N/A

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which indicates the optical wavelength.

Y

Y

N/A

1310

Wavelength 1310

Y

Y

N/A

1470

Wavelength 1470

Y

Y

N/A

1490

Wavelength 1490

Y

Y

N/A

1510

Wavelength 1510

Y

Y

N/A

1529.55

Wavelength 1529.55

Y

Y

N/A

1529.94

Wavelength 1529.94

Y

Y

N/A

1530

Wavelength 1530

Y

Y

N/A

1530.33

Wavelength 1530.33

Y

Y

N/A

1530.73

Wavelength 1530.73

Y

Y

N/A

1531.12

Wavelength 1531.12

Y

Y

N/A

1531.51

Wavelength 1531.51

Y

Y

N/A

1531.90

Wavelength 1531.90

Y

Y

N/A

1532.29

Wavelength 1532.29

Y

Y

N/A

1532.68

Wavelength 1532.68

Y

Y

N/A

1533.07

Wavelength 1533.07

Y

Y

N/A

1533.47

Wavelength 1533.47

Y

Y

N/A

1533.86

Wavelength 1533.86

Y

Y

N/A

1534.25

Wavelength 1534.25

Y

Y

N/A

1534.64

Wavelength 1534.64

Y

Y

N/A

1535.04

Wavelength 1535.04

Y

Y

N/A

1535.43

Wavelength 1535.43

Y

Y

N/A

1535.82

Wavelength 1535.82

Y

Y

N/A

1536.22

Wavelength 1536.22

Y

Y

N/A

1536.61

Wavelength 1536.61

Y

Y

N/A

1537

Wavelength 1537

Y

Y

N/A

1537.40

Wavelength 1537.40

Y

Y

N/A

1537.79

Wavelength 1537.79

Y

Y

N/A

1538.19

Wavelength 1538.19

Y

Y

N/A

1538.58

Wavelength 1538.58

Y

Y

N/A

1538.98

Wavelength 1538.98

Y

Y

N/A

1539.37

Wavelength 1539.37

Y

Y

N/A

1539.77

Wavelength 1539.77

Y

Y

N/A

1540.16

Wavelength 1540.16

Y

Y

N/A

1540.56

Wavelength 1540.56

Y

Y

N/A

1540.95

Wavelength 1540.95

Y

Y

N/A

1541.35

Wavelength 1541.35

Y

Y

N/A

1541.75

Wavelength 1541.75

Y

Y

N/A

1542.14

Wavelength 1542.14

Y

Y

N/A

1542.35

Wavelength 1542.35

Y

Y

N/A

1542.54

Wavelength 1542.54

Y

Y

N/A

1542.94

Wavelength 1542.94

Y

Y

N/A

1543.33

Wavelength 1543.33

Y

Y

N/A

1543.73

Wavelength 1543.73

Y

Y

N/A

1544.13

Wavelength 1544.13

Y

Y

N/A

1544.53

Wavelength 1544.53

Y

Y

N/A

1544.92

Wavelength 1544.92

Y

Y

N/A

1545.32

Wavelength 1545.32

Y

Y

N/A

1545.72

Wavelength 1545.72

Y

Y

N/A

1546.12

Wavelength 1546.12

Y

Y

N/A

1546.52

Wavelength 1546.52

Y

Y

N/A

1546.92

Wavelength 1546.92

Y

Y

N/A

1547.32

Wavelength 1547.32

Y

Y

N/A

1547.72

Wavelength 1547.72

Y

Y

N/A

1548.12

Wavelength 1548.12

Y

Y

N/A

1548.51

Wavelength 1548.51

Y

Y

N/A

1548.92

Wavelength 1548.92

Y

Y

N/A

1549.32

Wavelength 1549.32

Y

Y

N/A

1549.71

Wavelength 1549.71

Y

Y

N/A

1550

Wavelength 1500

Y

Y

N/A

1550.12

Wavelength 1550.12

Y

Y

N/A

1550.52

Wavelength 1550.52

Y

Y

N/A

1550.92

Wavelength 1550.92

Y

Y

N/A

1551.32

Wavelength 1551.32

Y

Y

N/A

1551.72

Wavelength 1551.72

Y

Y

N/A

1552.12

Wavelength 1552.12

Y

Y

N/A

1552.52

Wavelength 1552.52

Y

Y

N/A

1552.93

Wavelength 1552.93

Y

Y

N/A

1553.33

Wavelength 1553.33

Y

Y

N/A

1553.73

Wavelength 1553.73

Y

Y

N/A

1554.13

Wavelength 1554.13

Y

Y

N/A

1554.13

Wavelength 1554.13

Y

Y

N/A

1554.94

Wavelength 1554.94

Y

Y

N/A

1555.34

Wavelength 1555.34

Y

Y

N/A

1555.75

Wavelength 1555.75

Y

Y

N/A

1556.15

Wavelength 1556.15

Y

Y

N/A

1556.55

Wavelength 1556.55

Y

Y

N/A

1556.96

Wavelength 1556.96

Y

Y

N/A

1557.36

Wavelength 1557.36

Y

Y

N/A

1557.77

Wavelength 1557.77

Y

Y

N/A

1558.17

Wavelength 1558.17

Y

Y

N/A

1558.58

Wavelength 1558.58

Y

Y

N/A

1558.98

Wavelength 1558.98

Y

Y

N/A

1559.39

Wavelength 1559.39

Y

Y

N/A

1559.79

Wavelength 1559.79

Y

Y

N/A

1560.20

Wavelength 1560.20

Y

Y

N/A

1560.61

Wavelength 1560.61

Y

Y

N/A

1561.01

Wavelength 1561.01

Y

Y

N/A

1561.42

Wavelength 1561.42

Y

Y

N/A

1561.83

Wavelength 1561.83

Y

Y

N/A

1570

Wavelength 1570

Y

Y

N/A

1570.83

Wavelength 1570.83

Y

Y

N/A

1571.24

Wavelength 1571.24

Y

Y

N/A

1571.65

Wavelength 1571.65

Y

Y

N/A

1572.06

Wavelength 1572.06

Y

Y

N/A

1572.48

Wavelength 1572.48

Y

Y

N/A

1572.89

Wavelength 1572.89

Y

Y

N/A

1573.30

Wavelength 1573.30

Y

Y

N/A

1573.71

Wavelength 1573.71

Y

Y

N/A

1574.13

Wavelength 1574.13

Y

Y

N/A

1574.54

Wavelength 1574.54

Y

Y

N/A

1574.95

Wavelength 1574.95

Y

Y

N/A

1575.37

Wavelength 1575.37

Y

Y

N/A

1575.78

Wavelength 1575.78

Y

Y

N/A

1576.20

Wavelength 1576.20

Y

Y

N/A

1576.61

Wavelength 1576.61

Y

Y

N/A

1577.03

Wavelength 1577.03

Y

Y

N/A

1577.44

Wavelength 1577.44

Y

Y

N/A

1577.86

Wavelength 1577.86

Y

Y

N/A

1578.27

Wavelength 1578.27

Y

Y

N/A

1578.69

Wavelength 1578.69

Y

Y

N/A

1579.10

Wavelength 1579.10

Y

Y

N/A

1579.52

Wavelength 1579.52

Y

Y

N/A

1579.93

Wavelength 1579.93

Y

Y

N/A

1580.35

Wavelength 1580.35

Y

Y

N/A

1580.77

Wavelength 1580.77

Y

Y

N/A

1581.18

Wavelength 1581.18

Y

Y

N/A

1581.60

Wavelength 1581.60

Y

Y

N/A

1582.02

Wavelength 1582.02

Y

Y

N/A

1582.44

Wavelength 1582.44

Y

Y

N/A

1582.85

Wavelength 1582.85

Y

Y

N/A

1583.27

Wavelength 1583.27

Y

Y

N/A

1583.69

Wavelength 1583.69

Y

Y

N/A

1584.11

Wavelength 1584.11

Y

Y

N/A

1584.53

Wavelength 1584.53

Y

Y

N/A

1584.95

Wavelength 1584.95

Y

Y

N/A

1585.36

Wavelength 1585.36

Y

Y

N/A

1585.78

Wavelength 1585.78

Y

Y

N/A

1586.20

Wavelength 1586.20

Y

Y

N/A

1586.62

Wavelength 1586.62

Y

Y

N/A

1587.04

Wavelength 1587.04

Y

Y

N/A

1587.46

Wavelength 1587.46

Y

Y

N/A

1587.88

Wavelength 1587.88

Y

Y

N/A

1588.30

Wavelength 1588.30

Y

Y

N/A

1588.73

Wavelength 1588.73

Y

Y

N/A

1589.15

Wavelength 1589.15

Y

Y

N/A

1589.57

Wavelength 1589.57

Y

Y

N/A

1589.99

Wavelength 1589.99

Y

Y

N/A

1590

Wavelength 1590

Y

Y

N/A

1590.41

Wavelength 1590.41

Y

Y

N/A

1590.83

Wavelength 1590.83

Y

Y

N/A

1591.26

Wavelength 1591.26

Y

Y

N/A

1591.68

Wavelength 1591.68

Y

Y

N/A

1592.10

Wavelength 1592.10

Y

Y

N/A

1592.52

Wavelength 1592.52

Y

Y

N/A

1592.95

Wavelength 1592.95

Y

Y

N/A

1593.37

Wavelength 1593.37

Y

Y

N/A

1593.79

Wavelength 1593.79

Y

Y

N/A

1594.22

Wavelength 1594.22

Y

Y

N/A

1594.64

Wavelength 1594.64

Y

Y

N/A

1595.06

Wavelength 1595.06

Y

Y

N/A

1595.49

Wavelength 1595.49

Y

Y

N/A

1596.34

Wavelength 1596.34

Y

Y

N/A

1596.76

Wavelength 1596.76

Y

Y

N/A

1597.19

Wavelength 1597.19

Y

Y

N/A

1597.62

Wavelength 1597.62

Y

Y

N/A

1598.04

Wavelength 1598.04

Y

Y

N/A

1598.47

Wavelength 1598.47

Y

Y

N/A

1598.89

Wavelength 1598.89

Y

Y

N/A

1599.32

Wavelength 1599.32

Y

Y

N/A

1599.75

Wavelength 1599.75

Y

Y

N/A

1600.06

Wavelength 1600.06

Y

Y

N/A

1601.03

Wavelength 1601.03

Y

Y

N/A

1601.46

Wavelength 1601.46

Y

Y

N/A

1601.88

Wavelength 1601.88

Y

Y

N/A

1602.31

Wavelength 1602.31

Y

Y

N/A

1602.74

Wavelength 1602.74

Y

Y

N/A

1603.17

Wavelength 1603.17

Y

Y

N/A

1603.60

Wavelength 1603.60

Y

Y

N/A

1604.03

Wavelength 1604.03

Y

Y

N/A

1610

Wavelength 1610

Y

Y

N/A

USE-TWL1

Use Tunable Wavelength 1

Y

Y

N/A

<LOSSB>

(Optional) The parameter type is REACH, which indicates the reach values.

Y

Y

N/A

AUTOPROV

Autoprovisioning

Y

Y

N/A

CX

Reach CX

Y

Y

N/A

DX

Reach DX

Y

Y

N/A

HX

Reach HX

Y

Y

N/A

I1

Reach I1

Y

Y

N/A

IR-1

Reach IR-1

Y

Y

N/A

IR-2

Reach IR-2

Y

Y

N/A

L1

Reach L1

Y

Y

N/A

L2

Reach L2

Y

Y

N/A

L3

Reach L3

Y

Y

N/A

LR-1

Reach LR-1

Y

Y

N/A

LR-2

Reach LR-2

Y

Y

N/A

LR-3

Reach LR-3

Y

Y

N/A

LX

Reach LX

Y

Y

N/A

S1

Reach S1

Y

Y

N/A

S2

Reach S2

Y

Y

N/A

SR

Reach SR

Y

Y

N/A

SR-1

Reach SR-1

Y

Y

N/A

SX

Reach SX

Y

Y

N/A

T

Reach T

Y

Y

N/A

VX

Reach VX

Y

Y

N/A

ZX

Reach ZX

Y

Y

N/A

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer. Defaults to 32.

Y

Y

N/A

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

Y

N/A

Unlocked

In service

Y

Y

N/A

Locked

Out of service

Y

Y

N/A

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

Y

N/A

AutomaticInService

Automatic in service

Y

Y

N/A

Disabled

Disabled

Y

Y

N/A

Loopback

Loopback

Y

Y

N/A

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

Y

N/A

MT

Maintenance mode

Y

Y

N/A

OutOfGroup

Out of group

Y

Y

N/A

SoftwareDownload

Software downloading

Y

Y

N/A

Unassigned

Unassigned

Y

Y

N/A

NotInstalled

Unequipped

Y

Y

N/A


11.2  ED-<MOD1FCPAYLOAD>

(Cisco ONS 15454 SDH) The Edit 1GISC3, 2GISC3, D1VIDEO, DV6000, ESCON, ETRCLO, HDTV or PASSTHRU (ED-<MOD1FCPAYLOAD>) command edits the attributes related with the Fibre Channel facility. The state Locked,AutomaticInService is not supported on the FC port. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The user can change the service state of a facility to locked-enabled or disabled, only if all the following conditions are met

The facility is not sourcing a synchronization clock

The facility's DCC is disabled.

The facility is not part of a protection group

The facility is not supporting cross-connects


Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service with no consideration for orderly interruption. Do not use in scripts or automated batch operations.



Note To completely disable the CMDMDE=FRCD option, provision the <to be defined parameter> in the NE defaults to FALSE. This will prevent the FRCD option from being honored by the NE. The NE default parameter can be provisioned using the CTC only.



NoteThe port parameters VIZ, LINKRCVRY, DISTEXTN, AUTODETECTION, LINKCREDITS, and MFS can be edited only if the port state is OOS, Maintenance or OOS,DSBLD.

The port parameters AUTODETECTION, LINKCREDITS, and MFS can be edited only if distance extension is enabled (set to B2B).

When 1GFICON and 2GFICON payloads are provisioned, distance extension=B2B is the default and only valid setting. Setting distance extension (using the ED-nGFICON command) to any other setting will be denied with an error message, for example, Provisioning Rules Failed.


Category

Ports

Security

Provisioning

Input Format

ED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],[DISTEXTN= <DISTANCE_EXTENSION>],[AUTODETECTION=<AUTO_DETECTION>], [LINKCREDITS=<CREDITS>],[FASTSWITCH=<FASTSWITCH>],[MFS=<MAXFRMSIZE>] ,[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],[SQUELCH=<SQUELCH>][:<PST>[,<SST>]];

Input Example

ED-1GFC:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,FASTSWITCH= ,MFS=2148,NAME="FC PORT",CMDMDE=NORM,SOAK=32,
FREQ=1550,LOSSB=LR-1:LOCKED,MAINTENANCE;

Table 11-2 ED-<MOD1FCPAYLOAD> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

N/A

N/A

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.

Y

N/A

N/A

N

Disable an attribute.

Y

N/A

N/A

Y

Enable an attribute.

Y

N/A

N/A

<DISTEXTN>

(Optional) Distance extension. It can be set to Buffer-to-Buffer (B2B) Credit Management state or None. The parameter type is DISTANCE_EXTENSION (distance extension).

Note B2B and link recovery are mutually exclusive. You cannot turn on both B2B and link recovery at the same time.

Y

N/A

N/A

B2B

Buffer to buffer flow control

Y

N/A

N/A

NONE

No distance extension

Y

N/A

N/A

<AUTODETECTION>

(Optional) Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.

Y

N/A

N/A

N

Disable an attribute.

Y

N/A

N/A

Y

Enable an attribute.

Y

N/A

N/A

<LINKCREDITS>

(Optional) Number of link credits. If autodetection is set to off, the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.

Y

N/A

N/A

<FASTSWITCH>

<TBD>

     

<MFS>

(Optional) Maximum frame size. MFS is an integer.

Y

N/A

N/A

<NAME>

(Optional) NAME is a string. User-assigned port name.

Y

N/A

N/A

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

N/A

FRCD

Force the system to override a state in which the command would normally be denied.

Y

N/A

N/A

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

N/A

N/A

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

Y

N/A

N/A

<FREQ>

(Optional) Parameter type is OPTICAL_WLEN (optical wavelength).

Y

N/A

N/A

1310

Wavelength 1310

Y

N/A

N/A

1470

Wavelength 1470

Y

N/A

N/A

1490

Wavelength 1490

Y

N/A

N/A

1510

Wavelength 1510

Y

N/A

N/A

1529.55

Wavelength 1529.55

Y

N/A

N/A

1529.94

Wavelength 1529.94

Y

N/A

N/A

1530

Wavelength 1530

Y

N/A

N/A

1530.33

Wavelength 1530.33

Y

N/A

N/A

1530.73

Wavelength 1530.73

Y

N/A

N/A

1531.12

Wavelength 1531.12

Y

N/A

N/A

1531.51

Wavelength 1531.51

Y

N/A

N/A

1531.90

Wavelength 1531.90

Y

N/A

N/A

1532.29

Wavelength 1532.29

Y

N/A

N/A

1532.68

Wavelength 1532.68

Y

N/A

N/A

1533.07

Wavelength 1533.07

Y

N/A

N/A

1533.47

Wavelength 1533.47

Y

N/A

N/A

1533.86

Wavelength 1533.86

Y

N/A

N/A

1534.25

Wavelength 1534.25

Y

N/A

N/A

1534.64

Wavelength 1534.64

Y

N/A

N/A

1535.04

Wavelength 1535.04

Y

N/A

N/A

1535.43

Wavelength 1535.43

Y

N/A

N/A

1535.82

Wavelength 1535.82

Y

N/A

N/A

1536.22

Wavelength 1536.22

Y

N/A

N/A

1536.61

Wavelength 1536.61

Y

N/A

N/A

1537

Wavelength 1537

Y

N/A

N/A

1537.40

Wavelength 1537.40

Y

N/A

N/A

1537.79

Wavelength 1537.79

Y

N/A

N/A

1538.19

Wavelength 1538.19

Y

N/A

N/A

1538.58

Wavelength 1538.58

Y

N/A

N/A

1538.98

Wavelength 1538.98

Y

N/A

N/A

1539.37

Wavelength 1539.37

Y

N/A

N/A

1539.77

Wavelength 1539.77

Y

N/A

N/A

1540.16

Wavelength 1540.16

Y

N/A

N/A

1540.56

Wavelength 1540.56

Y

N/A

N/A

1540.95

Wavelength 1540.95

Y

N/A

N/A

1541.35

Wavelength 1541.35

Y

N/A

N/A

1541.75

Wavelength 1541.75

Y

N/A

N/A

1542.14

Wavelength 1542.14

Y

N/A

N/A

1542.35

Wavelength 1542.35

Y

N/A

N/A

1542.54

Wavelength 1542.54

Y

N/A

N/A

1542.94

Wavelength 1542.94

Y

N/A

N/A

1543.33

Wavelength 1543.33

Y

N/A

N/A

1543.73

Wavelength 1543.73

Y

N/A

N/A

1544.13

Wavelength 1544.13

Y

N/A

N/A

1544.53

Wavelength 1544.53

Y

N/A

N/A

1544.92

Wavelength 1544.92

Y

N/A

N/A

1545.32

Wavelength 1545.32

Y

N/A

N/A

1545.72

Wavelength 1545.72

Y

N/A

N/A

1546.12

Wavelength 1546.12

Y

N/A

N/A

1546.52

Wavelength 1546.52

Y

N/A

N/A

1546.92

Wavelength 1546.92

Y

N/A

N/A

1547.32

Wavelength 1547.32

Y

N/A

N/A

1547.72

Wavelength 1547.72

Y

N/A

N/A

1548.12

Wavelength 1548.12

Y

N/A

N/A

1548.51

Wavelength 1548.51

Y

N/A

N/A

1548.92

Wavelength 1548.92

Y

N/A

N/A

1549.32

Wavelength 1549.32

Y

N/A

N/A

1549.71

Wavelength 1549.71

Y

N/A

N/A

1550

Wavelength 1500

Y

N/A

N/A

1550.12

Wavelength 1550.12

Y

N/A

N/A

1550.52

Wavelength 1550.52

Y

N/A

N/A

1550.92

Wavelength 1550.92

Y

N/A

N/A

1551.32

Wavelength 1551.32

Y

N/A

N/A

1551.72

Wavelength 1551.72

Y

N/A

N/A

1552.12

Wavelength 1552.12

Y

N/A

N/A

1552.52

Wavelength 1552.52

Y

N/A

N/A

1552.93

Wavelength 1552.93

Y

N/A

N/A

1553.33

Wavelength 1553.33

Y

N/A

N/A

1553.73

Wavelength 1553.73

Y

N/A

N/A

1554.13

Wavelength 1554.13

Y

N/A

N/A

1554.13

Wavelength 1554.13

Y

N/A

N/A

1554.94

Wavelength 1554.94

Y

N/A

N/A

1555.34

Wavelength 1555.34

Y

N/A

N/A

1555.75

Wavelength 1555.75

Y

N/A

N/A

1556.15

Wavelength 1556.15

Y

N/A

N/A

1556.55

Wavelength 1556.55

Y

N/A

N/A

1556.96

Wavelength 1556.96

Y

N/A

N/A

1557.36

Wavelength 1557.36

Y

N/A

N/A

1557.77

Wavelength 1557.77

Y

N/A

N/A

1558.17

Wavelength 1558.17

Y

N/A

N/A

1558.58

Wavelength 1558.58

Y

N/A

N/A

1558.98

Wavelength 1558.98

Y

N/A

N/A

1559.39

Wavelength 1559.39

Y

N/A

N/A

1559.79

Wavelength 1559.79

Y

N/A

N/A

1560.20

Wavelength 1560.20

Y

N/A

N/A

1560.61

Wavelength 1560.61

Y

N/A

N/A

1561.01

Wavelength 1561.01

Y

N/A

N/A

1561.42

Wavelength 1561.42

Y

N/A

N/A

1561.83

Wavelength 1561.83

Y

N/A

N/A

1570

Wavelength 1570

Y

N/A

N/A

1570.83

Wavelength 1570.83

Y

N/A

N/A

1571.24

Wavelength 1571.24

Y

N/A

N/A

1571.65

Wavelength 1571.65

Y

N/A

N/A

1572.06

Wavelength 1572.06

Y

N/A

N/A

1572.48

Wavelength 1572.48

Y

N/A

N/A

1572.89

Wavelength 1572.89

Y

N/A

N/A

1573.30

Wavelength 1573.30

Y

N/A

N/A

1573.71

Wavelength 1573.71

Y

N/A

N/A

1574.13

Wavelength 1574.13

Y

N/A

N/A

1574.54

Wavelength 1574.54

Y

N/A

N/A

1574.95

Wavelength 1574.95

Y

N/A

N/A

1575.37

Wavelength 1575.37

Y

N/A

N/A

1575.78

Wavelength 1575.78

Y

N/A

N/A

1576.20

Wavelength 1576.20

Y

N/A

N/A

1576.61

Wavelength 1576.61

Y

N/A

N/A

1577.03

Wavelength 1577.03

Y

N/A

N/A

1577.44

Wavelength 1577.44

Y

N/A

N/A

1577.86

Wavelength 1577.86

Y

N/A

N/A

1578.27

Wavelength 1578.27

Y

N/A

N/A

1578.69

Wavelength 1578.69

Y

N/A

N/A

1579.10

Wavelength 1579.10

Y

N/A

N/A

1579.52

Wavelength 1579.52

Y

N/A

N/A

1579.93

Wavelength 1579.93

Y

N/A

N/A

1580.35

Wavelength 1580.35

Y

N/A

N/A

1580.77

Wavelength 1580.77

Y

N/A

N/A

1581.18

Wavelength 1581.18

Y

N/A

N/A

1581.60

Wavelength 1581.60

Y

N/A

N/A

1582.02

Wavelength 1582.02

Y

N/A

N/A

1582.44

Wavelength 1582.44

Y

N/A

N/A

1582.85

Wavelength 1582.85

Y

N/A

N/A

1583.27

Wavelength 1583.27

Y

N/A

N/A

1583.69

Wavelength 1583.69

Y

N/A

N/A

1584.11

Wavelength 1584.11

Y

N/A

N/A

1584.53

Wavelength 1584.53

Y

N/A

N/A

1584.95

Wavelength 1584.95

Y

N/A

N/A

1585.36

Wavelength 1585.36

Y

N/A

N/A

1585.78

Wavelength 1585.78

Y

N/A

N/A

1586.20

Wavelength 1586.20

Y

N/A

N/A

1586.62

Wavelength 1586.62

Y

N/A

N/A

1587.04

Wavelength 1587.04

Y

N/A

N/A

1587.46

Wavelength 1587.46

Y

N/A

N/A

1587.88

Wavelength 1587.88

Y

N/A

N/A

1588.30

Wavelength 1588.30

Y

N/A

N/A

1588.73

Wavelength 1588.73

Y

N/A

N/A

1589.15

Wavelength 1589.15

Y

N/A

N/A

1589.57

Wavelength 1589.57

Y

N/A

N/A

1589.99

Wavelength 1589.99

Y

N/A

N/A

1590

Wavelength 1590

Y

N/A

N/A

1590.41

Wavelength 1590.41

Y

N/A

N/A

1590.83

Wavelength 1590.83

Y

N/A

N/A

1591.26

Wavelength 1591.26

Y

N/A

N/A

1591.68

Wavelength 1591.68

Y

N/A

N/A

1592.10

Wavelength 1592.10

Y

N/A

N/A

1592.52

Wavelength 1592.52

Y

N/A

N/A

1592.95

Wavelength 1592.95

Y

N/A

N/A

1593.37

Wavelength 1593.37

Y

N/A

N/A

1593.79

Wavelength 1593.79

Y

N/A

N/A

1594.22

Wavelength 1594.22

Y

N/A

N/A

1594.64

Wavelength 1594.64

Y

N/A

N/A

1595.06

Wavelength 1595.06

Y

N/A

N/A

1595.49

Wavelength 1595.49

Y

N/A

N/A

1596.34

Wavelength 1596.34

Y

N/A

N/A

1596.76

Wavelength 1596.76

Y

N/A

N/A

1597.19

Wavelength 1597.19

Y

N/A

N/A

1597.62

Wavelength 1597.62

Y

N/A

N/A

1598.04

Wavelength 1598.04

Y

N/A

N/A

1598.47

Wavelength 1598.47

Y

N/A

N/A

1598.89

Wavelength 1598.89

Y

N/A

N/A

1599.32

Wavelength 1599.32

Y

N/A

N/A

1599.75

Wavelength 1599.75

Y

N/A

N/A

1600.06

Wavelength 1600.06

Y

N/A

N/A

1601.03

Wavelength 1601.03

Y

N/A

N/A

1601.46

Wavelength 1601.46

Y

N/A

N/A

1601.88

Wavelength 1601.88

Y

N/A

N/A

1602.31

Wavelength 1602.31

Y

N/A

N/A

1602.74

Wavelength 1602.74

Y

N/A

N/A

1603.17

Wavelength 1603.17

Y

N/A

N/A

1603.60

Wavelength 1603.60

Y

N/A

N/A

1604.03

Wavelength 1604.03

Y

N/A

N/A

1610

Wavelength 1610

Y

N/A

N/A

USE-TWL1

Use Tunable Wavelength 1

Y

N/A

N/A

<LOSSB>

(Optional) Parameter type is REACH (reach values).

Y

N/A

N/A

AUTOPROV

Autoprovisioning

Y

N/A

N/A

CX

Reach CX

Y

N/A

N/A

DX

Reach DX

Y

N/A

N/A

HX

Reach HX

Y

N/A

N/A

I1

Reach I1

Y

N/A

N/A

IR-1

Reach IR-1

Y

N/A

N/A

IR-2

Reach IR-2

Y

N/A

N/A

L1

Reach L1

Y

N/A

N/A

L2

Reach L2

Y

N/A

N/A

L3

Reach L3

Y

N/A

N/A

LR-1

Reach LR-1

Y

N/A

N/A

LR-2

Reach LR-2

Y

N/A

N/A

LR-3

Reach LR-3

Y

N/A

N/A

LX

Reach LX

Y

N/A

N/A

S1

Reach S1

Y

N/A

N/A

S2

Reach S2

Y

N/A

N/A

SR

Reach SR

Y

N/A

N/A

SR-1

Reach SR-1

Y

N/A

N/A

SX

Reach SX

Y

N/A

N/A

T

Reach T

Y

N/A

N/A

VX

Reach VX

Y

N/A

N/A

ZX

Reach ZX

Y

N/A

N/A

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

N/A

Unlocked

In service

Y

N/A

N/A

Locked

Out of service

Y

N/A

N/A

<SST>

(Optional) Secondary state. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

N/A

AutomaticInService

Automatic in service

Y

N/A

N/A

Disabled

Disabled

Y

N/A

N/A

Loopback

Loopback

Y

N/A

N/A

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

N/A

Maintenance

Maintenance mode

Y

N/A

N/A

OutOfGroup

Out of group

Y

N/A

N/A

SoftwareDownload

Software downloading

Y

N/A

N/A

Unassigned

Unassigned

Y

N/A

N/A

NotInstalled

Unequipped

Y

N/A

N/A


11.3  ED-<MOD1FICONPAYLOAD>

(Cisco ONS 15454 SDH) The Edit 1GFICON, 2GFICON, 4GFICON, or ESCON (ED-<MOD1FICONPAYLOAD>) command edits the attributes related with the FICON payload facility. The state Locked,AutomaticInService is not supported on the FICON port. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

Ports

Security

Provisioning

Input Format

ED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],[DISTEXTN= <DISTANCE_EXTENSION>],[AUTODETECTION=<AUTO_DETECTION>], [LINKCREDITS=<CREDITS>],[FASTSWITCH=<FASTSWITCH>],[MFS=<MAXFRMSIZE>] ,[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],[SQUELCH=<SQUELCH>][:<PST>[,<SST>]];

Input Example

ED-1GFICON:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,FASTSWITCH= ,MFS=2148,NAME="FC PORT",CMDMDE=NORM,SOAK=32,
FREQ=1550,LOSSB=LR-1::LOCKED,MAINTENANCE;

Table 11-3 ED-<MOD1FICONPAYLOAD> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

N/A

N/A

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.

Y

N/A

N/A

N

Disable an attribute.

Y

N/A

N/A

Y

Enable an attribute.

Y

N/A

N/A

<DISTEXTN>

(Optional) Distance extension. It can be set to B2B Credit Management state or None. The parameter type is DISTANCE_EXTENSION.

Note B2B and link recovery are mutually exclusive. You cannot turn on both B2B and link recovery at the same time.

Y

N/A

N/A

B2B

Buffer to buffer flow control

Y

N/A

N/A

NONE

No distance extension

Y

N/A

N/A

<AUTODETECTION>

(Optional) Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.

Y

N/A

N/A

N

Disable an attribute.

Y

N/A

N/A

Y

Enable an attribute.

Y

N/A

N/A

<LINKCREDITS>

(Optional) Number of link credits. If autodetection is set to off, the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.

Y

N/A

N/A

<FASTSWITCH>

<TBD>

Y

N/A

N/A

<MFS>

Maximum frame size. MFS is an integer.

Y

N/A

N/A

<NAME>

NAME is a string. User-assigned port name.

Y

N/A

N/A

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

N/A

FRCD

Force the system to override a state in which the command would normally be denied.

Y

N/A

N/A

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

N/A

N/A

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

Y

N/A

N/A

<FREQ>

(Optional) Parameter type is OPTICAL_WLEN, which is the optical wavelength.

Y

N/A

N/A

1310

Wavelength 1310

Y

N/A

N/A

1470

Wavelength 1470

Y

N/A

N/A

1490

Wavelength 1490

Y

N/A

N/A

1510

Wavelength 1510

Y

N/A

N/A

1529.55

Wavelength 1529.55

Y

N/A

N/A

1529.94

Wavelength 1529.94

Y

N/A

N/A

1530

Wavelength 1530

Y

N/A

N/A

1530.33

Wavelength 1530.33

Y

N/A

N/A

1530.73

Wavelength 1530.73

Y

N/A

N/A

1531.12

Wavelength 1531.12

Y

N/A

N/A

1531.51

Wavelength 1531.51

Y

N/A

N/A

1531.90

Wavelength 1531.90

Y

N/A

N/A

1532.29

Wavelength 1532.29

Y

N/A

N/A

1532.68

Wavelength 1532.68

Y

N/A

N/A

1533.07

Wavelength 1533.07

Y

N/A

N/A

1533.47

Wavelength 1533.47

Y

N/A

N/A

1533.86

Wavelength 1533.86

Y

N/A

N/A

1534.25

Wavelength 1534.25

Y

N/A

N/A

1534.64

Wavelength 1534.64

Y

N/A

N/A

1535.04

Wavelength 1535.04

Y

N/A

N/A

1535.43

Wavelength 1535.43

Y

N/A

N/A

1535.82

Wavelength 1535.82

Y

N/A

N/A

1536.22

Wavelength 1536.22

Y

N/A

N/A

1536.61

Wavelength 1536.61

Y

N/A

N/A

1537

Wavelength 1537

Y

N/A

N/A

1537.40

Wavelength 1537.40

Y

N/A

N/A

1537.79

Wavelength 1537.79

Y

N/A

N/A

1538.19

Wavelength 1538.19

Y

N/A

N/A

1538.58

Wavelength 1538.58

Y

N/A

N/A

1538.98

Wavelength 1538.98

Y

N/A

N/A

1539.37

Wavelength 1539.37

Y

N/A

N/A

1539.77

Wavelength 1539.77

Y

N/A

N/A

1540.16

Wavelength 1540.16

Y

N/A

N/A

1540.56

Wavelength 1540.56

Y

N/A

N/A

1540.95

Wavelength 1540.95

Y

N/A

N/A

1541.35

Wavelength 1541.35

Y

N/A

N/A

1541.75

Wavelength 1541.75

Y

N/A

N/A

1542.14

Wavelength 1542.14

Y

N/A

N/A

1542.35

Wavelength 1542.35

Y

N/A

N/A

1542.54

Wavelength 1542.54

Y

N/A

N/A

1542.94

Wavelength 1542.94

Y

N/A

N/A

1543.33

Wavelength 1543.33

Y

N/A

N/A

1543.73

Wavelength 1543.73

Y

N/A

N/A

1544.13

Wavelength 1544.13

Y

N/A

N/A

1544.53

Wavelength 1544.53

Y

N/A

N/A

1544.92

Wavelength 1544.92

Y

N/A

N/A

1545.32

Wavelength 1545.32

Y

N/A

N/A

1545.72

Wavelength 1545.72

Y

N/A

N/A

1546.12

Wavelength 1546.12

Y

N/A

N/A

1546.52

Wavelength 1546.52

Y

N/A

N/A

1546.92

Wavelength 1546.92

Y

N/A

N/A

1547.32

Wavelength 1547.32

Y

N/A

N/A

1547.72

Wavelength 1547.72

Y

N/A

N/A

1548.12

Wavelength 1548.12

Y

N/A

N/A

1548.51

Wavelength 1548.51

Y

N/A

N/A

1548.92

Wavelength 1548.92

Y

N/A

N/A

1549.32

Wavelength 1549.32

Y

N/A

N/A

1549.71

Wavelength 1549.71

Y

N/A

N/A

1550

Wavelength 1500

Y

N/A

N/A

1550.12

Wavelength 1550.12

Y

N/A

N/A

1550.52

Wavelength 1550.52

Y

N/A

N/A

1550.92

Wavelength 1550.92

Y

N/A

N/A

1551.32

Wavelength 1551.32

Y

N/A

N/A

1551.72

Wavelength 1551.72

Y

N/A

N/A

1552.12

Wavelength 1552.12

Y

N/A

N/A

1552.52

Wavelength 1552.52

Y

N/A

N/A

1552.93

Wavelength 1552.93

Y

N/A

N/A

1553.33

Wavelength 1553.33

Y

N/A

N/A

1553.73

Wavelength 1553.73

Y

N/A

N/A

1554.13

Wavelength 1554.13

Y

N/A

N/A

1554.13

Wavelength 1554.13

Y

N/A

N/A

1554.94

Wavelength 1554.94

Y

N/A

N/A

1555.34

Wavelength 1555.34

Y

N/A

N/A

1555.75

Wavelength 1555.75

Y

N/A

N/A

1556.15

Wavelength 1556.15

Y

N/A

N/A

1556.55

Wavelength 1556.55

Y

N/A

N/A

1556.96

Wavelength 1556.96

Y

N/A

N/A

1557.36

Wavelength 1557.36

Y

N/A

N/A

1557.77

Wavelength 1557.77

Y

N/A

N/A

1558.17

Wavelength 1558.17

Y

N/A

N/A

1558.58

Wavelength 1558.58

Y

N/A

N/A

1558.98

Wavelength 1558.98

Y

N/A

N/A

1559.39

Wavelength 1559.39

Y

N/A

N/A

1559.79

Wavelength 1559.79

Y

N/A

N/A

1560.20

Wavelength 1560.20

Y

N/A

N/A

1560.61

Wavelength 1560.61

Y

N/A

N/A

1561.01

Wavelength 1561.01

Y

N/A

N/A

1561.42

Wavelength 1561.42

Y

N/A

N/A

1561.83

Wavelength 1561.83

Y

N/A

N/A

1570

Wavelength 1570

Y

N/A

N/A

1570.83

Wavelength 1570.83

Y

N/A

N/A

1571.24

Wavelength 1571.24

Y

N/A

N/A

1571.65

Wavelength 1571.65

Y

N/A

N/A

1572.06

Wavelength 1572.06

Y

N/A

N/A

1572.48

Wavelength 1572.48

Y

N/A

N/A

1572.89

Wavelength 1572.89

Y

N/A

N/A

1573.30

Wavelength 1573.30

Y

N/A

N/A

1573.71

Wavelength 1573.71

Y

N/A

N/A

1574.13

Wavelength 1574.13

Y

N/A

N/A

1574.54

Wavelength 1574.54

Y

N/A

N/A

1574.95

Wavelength 1574.95

Y

N/A

N/A

1575.37

Wavelength 1575.37

Y

N/A

N/A

1575.78

Wavelength 1575.78

Y

N/A

N/A

1576.20

Wavelength 1576.20

Y

N/A

N/A

1576.61

Wavelength 1576.61

Y

N/A

N/A

1577.03

Wavelength 1577.03

Y

N/A

N/A

1577.44

Wavelength 1577.44

Y

N/A

N/A

1577.86

Wavelength 1577.86

Y

N/A

N/A

1578.27

Wavelength 1578.27

Y

N/A

N/A

1578.69

Wavelength 1578.69

Y

N/A

N/A

1579.10

Wavelength 1579.10

Y

N/A

N/A

1579.52

Wavelength 1579.52

Y

N/A

N/A

1579.93

Wavelength 1579.93

Y

N/A

N/A

1580.35

Wavelength 1580.35

Y

N/A

N/A

1580.77

Wavelength 1580.77

Y

N/A

N/A

1581.18

Wavelength 1581.18

Y

N/A

N/A

1581.60

Wavelength 1581.60

Y

N/A

N/A

1582.02

Wavelength 1582.02

Y

N/A

N/A

1582.44

Wavelength 1582.44

Y

N/A

N/A

1582.85

Wavelength 1582.85

Y

N/A

N/A

1583.27

Wavelength 1583.27

Y

N/A

N/A

1583.69

Wavelength 1583.69

Y

N/A

N/A

1584.11

Wavelength 1584.11

Y

N/A

N/A

1584.53

Wavelength 1584.53

Y

N/A

N/A

1584.95

Wavelength 1584.95

Y

N/A

N/A

1585.36

Wavelength 1585.36

Y

N/A

N/A

1585.78

Wavelength 1585.78

Y

N/A

N/A

1586.20

Wavelength 1586.20

Y

N/A

N/A

1586.62

Wavelength 1586.62

Y

N/A

N/A

1587.04

Wavelength 1587.04

Y

N/A

N/A

1587.46

Wavelength 1587.46

Y

N/A

N/A

1587.88

Wavelength 1587.88

Y

N/A

N/A

1588.30

Wavelength 1588.30

Y

N/A

N/A

1588.73

Wavelength 1588.73

Y

N/A

N/A

1589.15

Wavelength 1589.15

Y

N/A

N/A

1589.57

Wavelength 1589.57

Y

N/A

N/A

1589.99

Wavelength 1589.99

Y

N/A

N/A

1590

Wavelength 1590

Y

N/A

N/A

1590.41

Wavelength 1590.41

Y

N/A

N/A

1590.83

Wavelength 1590.83

Y

N/A

N/A

1591.26

Wavelength 1591.26

Y

N/A

N/A

1591.68

Wavelength 1591.68

Y

N/A

N/A

1592.10

Wavelength 1592.10

Y

N/A

N/A

1592.52

Wavelength 1592.52

Y

N/A

N/A

1592.95

Wavelength 1592.95

Y

N/A

N/A

1593.37

Wavelength 1593.37

Y

N/A

N/A

1593.79

Wavelength 1593.79

Y

N/A

N/A

1594.22

Wavelength 1594.22

Y

N/A

N/A

1594.64

Wavelength 1594.64

Y

N/A

N/A

1595.06

Wavelength 1595.06

Y

N/A

N/A

1595.49

Wavelength 1595.49

Y

N/A

N/A

1596.34

Wavelength 1596.34

Y

N/A

N/A

1596.76

Wavelength 1596.76

Y

N/A

N/A

1597.19

Wavelength 1597.19

Y

N/A

N/A

1597.62

Wavelength 1597.62

Y

N/A

N/A

1598.04

Wavelength 1598.04

Y

N/A

N/A

1598.47

Wavelength 1598.47

Y

N/A

N/A

1598.89

Wavelength 1598.89

Y

N/A

N/A

1599.32

Wavelength 1599.32

Y

N/A

N/A

1599.75

Wavelength 1599.75

Y

N/A

N/A

1600.06

Wavelength 1600.06

Y

N/A

N/A

1601.03

Wavelength 1601.03

Y

N/A

N/A

1601.46

Wavelength 1601.46

Y

N/A

N/A

1601.88

Wavelength 1601.88

Y

N/A

N/A

1602.31

Wavelength 1602.31

Y

N/A

N/A

1602.74

Wavelength 1602.74

Y

N/A

N/A

1603.17

Wavelength 1603.17

Y

N/A

N/A

1603.60

Wavelength 1603.60

Y

N/A

N/A

1604.03

Wavelength 1604.03

Y

N/A

N/A

1610

Wavelength 1610

Y

N/A

N/A

USE-TWL1

Use Tunable Wavelength 1

Y

N/A

N/A

<LOSSB>

The parameter type is REACH, which is the reach value.

Y

N/A

N/A

AUTOPROV

Autoprovisioning

Y

N/A

N/A

CX

Reach CX

Y

N/A

N/A

DX

Reach DX

Y

N/A

N/A

HX

Reach HX

Y

N/A

N/A

I1

Reach I1

Y

N/A

N/A

IR-1

Reach IR-1

Y

N/A

N/A

IR-2

Reach IR-2

Y

N/A

N/A

L1

Reach L1

Y

N/A

N/A

L2

Reach L2

Y

N/A

N/A

L3

Reach L3

Y

N/A

N/A

LR-1

Reach LR-1

Y

N/A

N/A

LR-2

Reach LR-2

Y

N/A

N/A

LR-3

Reach LR-3

Y

N/A

N/A

LX

Reach LX

Y

N/A

N/A

S1

Reach S1

Y

N/A

N/A

S2

Reach S2

Y

N/A

N/A

SR

Reach SR

Y

N/A

N/A

SR-1

Reach SR-1

Y

N/A

N/A

SX

Reach SX

Y

N/A

N/A

T

Reach T

Y

N/A

N/A

VX

Reach VX

Y

N/A

N/A

ZX

Reach ZX

Y

N/A

N/A

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

N/A

Unlocked

In service

Y

N/A

N/A

Locked

Out of service

Y

N/A

N/A

<SST>

(Optional) Secondary state. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

N/A

AutomaticInService

Automatic in service

Y

N/A

N/A

Disabled

Disabled

Y

N/A

N/A

Loopback

Loopback

Y

N/A

N/A

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

N/A

Maintenance

Maintenance mode

Y

N/A

N/A

OutOfGroup

Out of group

Y

N/A

N/A

SoftwareDownload

Software downloading

Y

N/A

N/A

Unassigned

Unassigned

Y

N/A

N/A

NotInstalled

Unequipped

Y

N/A

N/A


11.4  ED-<MOD2DWDMPAYLOAD>

(Cisco ONS 15454 SDH) The Edit 10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, ESCON, ETRCLO, GIGE, HDTV, ISC3, or PASSTHRU (ED-<MOD2DWDMPAYLOAD>) command edits the operating parameters for a DWDM client facility. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

DWDM

Security

Provisioning

Input Format

ED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]];

Input Example

ED-HDTV::FAC-1-1:1:::NAME="PORTNAME",CMDMDE=NORM,FREQ=1550,
LOSSB=LR-1:UNLOCKED,AUTOMATICINSERVICE;

Table 11-4 ED-<MOD2DWDMPAYLOAD> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

N/A

N/A

<NAME>

(Optional) NAME is a string. User-assigned port name.

Y

N/A

N/A

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

N/A

FRCD

Force the system to override a state in which the command would normally be denied.

Y

N/A

N/A

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

N/A

N/A

<FREQ>

(Optional) Parameter type is OPTICAL_WLEN, which is the optical wavelength.

Y

N/A

N/A

1310

Wavelength 1310

Y

N/A

N/A

1470

Wavelength 1470

Y

N/A

N/A

1490

Wavelength 1490

Y

N/A

N/A

1510

Wavelength 1510

Y

N/A

N/A

1529.55

Wavelength 1529.55

Y

N/A

N/A

1529.94

Wavelength 1529.94

Y

N/A

N/A

1530

Wavelength 1530

Y

N/A

N/A

1530.33

Wavelength 1530.33

Y

N/A

N/A

1530.73

Wavelength 1530.73

Y

N/A

N/A

1531.12

Wavelength 1531.12

Y

N/A

N/A

1531.51

Wavelength 1531.51

Y

N/A

N/A

1531.90

Wavelength 1531.90

Y

N/A

N/A

1532.29

Wavelength 1532.29

Y

N/A

N/A

1532.68

Wavelength 1532.68

Y

N/A

N/A

1533.07

Wavelength 1533.07

Y

N/A

N/A

1533.47

Wavelength 1533.47

Y

N/A

N/A

1533.86

Wavelength 1533.86

Y

N/A

N/A

1534.25

Wavelength 1534.25

Y

N/A

N/A

1534.64

Wavelength 1534.64

Y

N/A

N/A

1535.04

Wavelength 1535.04

Y

N/A

N/A

1535.43

Wavelength 1535.43

Y

N/A

N/A

1535.82

Wavelength 1535.82

Y

N/A

N/A

1536.22

Wavelength 1536.22

Y

N/A

N/A

1536.61

Wavelength 1536.61

Y

N/A

N/A

1537

Wavelength 1537

Y

N/A

N/A

1537.40

Wavelength 1537.40

Y

N/A

N/A

1537.79

Wavelength 1537.79

Y

N/A

N/A

1538.19

Wavelength 1538.19

Y

N/A

N/A

1538.58

Wavelength 1538.58

Y

N/A

N/A

1538.98

Wavelength 1538.98

Y

N/A

N/A

1539.37

Wavelength 1539.37

Y

N/A

N/A

1539.77

Wavelength 1539.77

Y

N/A

N/A

1540.16

Wavelength 1540.16

Y

N/A

N/A

1540.56

Wavelength 1540.56

Y

N/A

N/A

1540.95

Wavelength 1540.95

Y

N/A

N/A

1541.35

Wavelength 1541.35

Y

N/A

N/A

1541.75

Wavelength 1541.75

Y

N/A

N/A

1542.14

Wavelength 1542.14

Y

N/A

N/A

1542.35

Wavelength 1542.35

Y

N/A

N/A

1542.54

Wavelength 1542.54

Y

N/A

N/A

1542.94

Wavelength 1542.94

Y

N/A

N/A

1543.33

Wavelength 1543.33

Y

N/A

N/A

1543.73

Wavelength 1543.73

Y

N/A

N/A

1544.13

Wavelength 1544.13

Y

N/A

N/A

1544.53

Wavelength 1544.53

Y

N/A

N/A

1544.92

Wavelength 1544.92

Y

N/A

N/A

1545.32

Wavelength 1545.32

Y

N/A

N/A

1545.72

Wavelength 1545.72

Y

N/A

N/A

1546.12

Wavelength 1546.12

Y

N/A

N/A

1546.52

Wavelength 1546.52

Y

N/A

N/A

1546.92

Wavelength 1546.92

Y

N/A

N/A

1547.32

Wavelength 1547.32

Y

N/A

N/A

1547.72

Wavelength 1547.72

Y

N/A

N/A

1548.12

Wavelength 1548.12

Y

N/A

N/A

1548.51

Wavelength 1548.51

Y

N/A

N/A

1548.92

Wavelength 1548.92

Y

N/A

N/A

1549.32

Wavelength 1549.32

Y

N/A

N/A

1549.71

Wavelength 1549.71

Y

N/A

N/A

1550

Wavelength 1500

Y

N/A

N/A

1550.12

Wavelength 1550.12

Y

N/A

N/A

1550.52

Wavelength 1550.52

Y

N/A

N/A

1550.92

Wavelength 1550.92

Y

N/A

N/A

1551.32

Wavelength 1551.32

Y

N/A

N/A

1551.72

Wavelength 1551.72

Y

N/A

N/A

1552.12

Wavelength 1552.12

Y

N/A

N/A

1552.52

Wavelength 1552.52

Y

N/A

N/A

1552.93

Wavelength 1552.93

Y

N/A

N/A

1553.33

Wavelength 1553.33

Y

N/A

N/A

1553.73

Wavelength 1553.73

Y

N/A

N/A

1554.13

Wavelength 1554.13

Y

N/A

N/A

1554.13

Wavelength 1554.13

Y

N/A

N/A

1554.94

Wavelength 1554.94

Y

N/A

N/A

1555.34

Wavelength 1555.34

Y

N/A

N/A

1555.75

Wavelength 1555.75

Y

N/A

N/A

1556.15

Wavelength 1556.15

Y

N/A

N/A

1556.55

Wavelength 1556.55

Y

N/A

N/A

1556.96

Wavelength 1556.96

Y

N/A

N/A

1557.36

Wavelength 1557.36

Y

N/A

N/A

1557.77

Wavelength 1557.77

Y

N/A

N/A

1558.17

Wavelength 1558.17

Y

N/A

N/A

1558.58

Wavelength 1558.58

Y

N/A

N/A

1558.98

Wavelength 1558.98

Y

N/A

N/A

1559.39

Wavelength 1559.39

Y

N/A

N/A

1559.79

Wavelength 1559.79

Y

N/A

N/A

1560.20

Wavelength 1560.20

Y

N/A

N/A

1560.61

Wavelength 1560.61

Y

N/A

N/A

1561.01

Wavelength 1561.01

Y

N/A

N/A

1561.42

Wavelength 1561.42

Y

N/A

N/A

1561.83

Wavelength 1561.83

Y

N/A

N/A

1570

Wavelength 1570

Y

N/A

N/A

1570.83

Wavelength 1570.83

Y

N/A

N/A

1571.24

Wavelength 1571.24

Y

N/A

N/A

1571.65

Wavelength 1571.65

Y

N/A

N/A

1572.06

Wavelength 1572.06

Y

N/A

N/A

1572.48

Wavelength 1572.48

Y

N/A

N/A

1572.89

Wavelength 1572.89

Y

N/A

N/A

1573.30

Wavelength 1573.30

Y

N/A

N/A

1573.71

Wavelength 1573.71

Y

N/A

N/A

1574.13

Wavelength 1574.13

Y

N/A

N/A

1574.54

Wavelength 1574.54

Y

N/A

N/A

1574.95

Wavelength 1574.95

Y

N/A

N/A

1575.37

Wavelength 1575.37

Y

N/A

N/A

1575.78

Wavelength 1575.78

Y

N/A

N/A

1576.20

Wavelength 1576.20

Y

N/A

N/A

1576.61

Wavelength 1576.61

Y

N/A

N/A

1577.03

Wavelength 1577.03

Y

N/A

N/A

1577.44

Wavelength 1577.44

Y

N/A

N/A

1577.86

Wavelength 1577.86

Y

N/A

N/A

1578.27

Wavelength 1578.27

Y

N/A

N/A

1578.69

Wavelength 1578.69

Y

N/A

N/A

1579.10

Wavelength 1579.10

Y

N/A

N/A

1579.52

Wavelength 1579.52

Y

N/A

N/A

1579.93

Wavelength 1579.93

Y

N/A

N/A

1580.35

Wavelength 1580.35

Y

N/A

N/A

1580.77

Wavelength 1580.77

Y

N/A

N/A

1581.18

Wavelength 1581.18

Y

N/A

N/A

1581.60

Wavelength 1581.60

Y

N/A

N/A

1582.02

Wavelength 1582.02

Y

N/A

N/A

1582.44

Wavelength 1582.44

Y

N/A

N/A

1582.85

Wavelength 1582.85

Y

N/A

N/A

1583.27

Wavelength 1583.27

Y

N/A

N/A

1583.69

Wavelength 1583.69

Y

N/A

N/A

1584.11

Wavelength 1584.11

Y

N/A

N/A

1584.53

Wavelength 1584.53

Y

N/A

N/A

1584.95

Wavelength 1584.95

Y

N/A

N/A

1585.36

Wavelength 1585.36

Y

N/A

N/A

1585.78

Wavelength 1585.78

Y

N/A

N/A

1586.20

Wavelength 1586.20

Y

N/A

N/A

1586.62

Wavelength 1586.62

Y

N/A

N/A

1587.04

Wavelength 1587.04

Y

N/A

N/A

1587.46

Wavelength 1587.46

Y

N/A

N/A

1587.88

Wavelength 1587.88

Y

N/A

N/A

1588.30

Wavelength 1588.30

Y

N/A

N/A

1588.73

Wavelength 1588.73

Y

N/A

N/A

1589.15

Wavelength 1589.15

Y

N/A

N/A

1589.57

Wavelength 1589.57

Y

N/A

N/A

1589.99

Wavelength 1589.99

Y

N/A

N/A

1590

Wavelength 1590

Y

N/A

N/A

1590.41

Wavelength 1590.41

Y

N/A

N/A

1590.83

Wavelength 1590.83

Y

N/A

N/A

1591.26

Wavelength 1591.26

Y

N/A

N/A

1591.68

Wavelength 1591.68

Y

N/A

N/A

1592.10

Wavelength 1592.10

Y

N/A

N/A

1592.52

Wavelength 1592.52

Y

N/A

N/A

1592.95

Wavelength 1592.95

Y

N/A

N/A

1593.37

Wavelength 1593.37

Y

N/A

N/A

1593.79

Wavelength 1593.79

Y

N/A

N/A

1594.22

Wavelength 1594.22

Y

N/A

N/A

1594.64

Wavelength 1594.64

Y

N/A

N/A

1595.06

Wavelength 1595.06

Y

N/A

N/A

1595.49

Wavelength 1595.49

Y

N/A

N/A

1596.34

Wavelength 1596.34

Y

N/A

N/A

1596.76

Wavelength 1596.76

Y

N/A

N/A

1597.19

Wavelength 1597.19

Y

N/A

N/A

1597.62

Wavelength 1597.62

Y

N/A

N/A

1598.04

Wavelength 1598.04

Y

N/A

N/A

1598.47

Wavelength 1598.47

Y

N/A

N/A

1598.89

Wavelength 1598.89

Y

N/A

N/A

1599.32

Wavelength 1599.32

Y

N/A

N/A

1599.75

Wavelength 1599.75

Y

N/A

N/A

1600.06

Wavelength 1600.06

Y

N/A

N/A

1601.03

Wavelength 1601.03

Y

N/A

N/A

1601.46

Wavelength 1601.46

Y

N/A

N/A

1601.88

Wavelength 1601.88

Y

N/A

N/A

1602.31

Wavelength 1602.31

Y

N/A

N/A

1602.74

Wavelength 1602.74

Y

N/A

N/A

1603.17

Wavelength 1603.17

Y

N/A

N/A

1603.60

Wavelength 1603.60

Y

N/A

N/A

1604.03

Wavelength 1604.03

Y

N/A

N/A

1610

Wavelength 1610

Y

N/A

N/A

USE-TWL1

Use Tunable Wavelength 1

Y

N/A

N/A

<LOSSB>

Parameter type is REACH, which is the reach value.

Y

N/A

N/A

AUTOPROV

Autoprovisioning

Y

N/A

N/A

CX

Reach CX

Y

N/A

N/A

DX

Reach DX

Y

N/A

N/A

HX

Reach HX

Y

N/A

N/A

I1

Reach I1

Y

N/A

N/A

IR-1

Reach IR-1

Y

N/A

N/A

IR-2

Reach IR-2

Y

N/A

N/A

L1

Reach L1

Y

N/A

N/A

L2

Reach L2

Y

N/A

N/A

L3

Reach L3

Y

N/A

N/A

LR-1

Reach LR-1

Y

N/A

N/A

LR-2

Reach LR-2

Y

N/A

N/A

LR-3

Reach LR-3

Y

N/A

N/A

LX

Reach LX

Y

N/A

N/A

S1

Reach S1

Y

N/A

N/A

S2

Reach S2

Y

N/A

N/A

SR

Reach SR

Y

N/A

N/A

SR-1

Reach SR-1

Y

N/A

N/A

SX

Reach SX

Y

N/A

N/A

T

Reach T

Y

N/A

N/A

VX

Reach VX

Y

N/A

N/A

ZX

Reach ZX

Y

N/A

N/A

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

N/A

Unlocked

In service

Y

N/A

N/A

Locked

Out of service

Y

N/A

N/A

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

N/A

AutomaticInService

Automatic in service

Y

N/A

N/A

Disabled

Disabled

Y

N/A

N/A

Loopback

Loopback

Y

N/A

N/A

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

N/A

Maintenance

Maintenance mode

Y

N/A

N/A

OutOfGroup

Out of group

Y

N/A

N/A

SoftwareDownload

Software downloading

Y

N/A

N/A

Unassigned

Unassigned

Y

N/A

N/A

NotInstalled

Unequipped

Y

N/A

N/A


11.5  ED-<MOD_PATH>

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit VC3, VC44C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (ED-<MOD_PATH>) command edits the attributes associated with VC paths.


Note The VC11 and VC64C modifiers are not supported on the Cisco ONS 15310 MA SDH platform.


The following modifiers are not supported on the Cisco ONS 15310 MA SDH platform.

Usage Guidelines

The SFBER, SDBER, RVRTV, and RVTM parameters only apply to subnetwork connection protection (SNCP) at the VC path level.

The path trace message is a 64-character string including the terminating carriage return (CR) and line feed (LF) that is transported in the J1 byte of the SDH VC Path overhead.

Both the EXPTRC and TRC string can be provisioned by a user with up to a 62-character string.The EXPTRC parameter indicates that the contents of the expected incoming path trace are provisioned by the user. The TRC parameter indicates the contents of the outgoing path trace message.

The INCTRC parameter indicates the contents of the incoming path trace message.

Path trace has three modes: OFF, MANUAL, and AUTO. The path trace mode defaults to OFF. The MANUAL mode performs the comparison of the received string with the user-entered expected string. The AUTO mode performs the comparison of the present received string with an expected string set to a previously received string. If there is a mismatch, TIM-P alarm is raised. When the path trace mode is in OFF mode, there is no path trace processing, and all the alarm and state conditions are reset.

The TACC parameter edits an existing single VC or VT and changes it to a test access point. When an editing command on TACC is executed, it assigns the VC or VT for the first two-way connection and VC+1 as the second 2-way connection. For single facility access digroup (FAD) test access, only a single VC/VT is used for the TAP creation. For more information on TACC, refer to the Cisco ONS SDH and Cisco ONS 15600 SDH TL1 Reference Guide.

J1 is implemented on the E1, E3, E4, DS3i-N-12, and STM cards.

E100 and E1000 cards do not support path trace.

J1 is supported on the STM1, STM4, STM16, E1, E3, and T3 cards on the Cisco ONS 15310 MA SDH platform.

The STM1, STM16AS, and STM64 cards only support EXPTRC in the ED-VC-PATH command.


Note Each TL1 command must be less than or equal to 255 characters. Any command larger than 255 characters must be split into multiple commands. For example, if you use the ED-<VC_PATH> command to edit the J1 EXPTRC/TRC message, SNCP attributes, and TACC attributes and the command exceeds 255 characters, the command will not be processed. You must use multiple ED-<VC_PATH> commands instead.


The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

The following actions will return error messages:

Sending this command to edit SFBER, SDBER, RVRTV or RVTM for the non-SNCP VC path.

Sending this command to edit the EXPTRC string with the AUTO path trace mode (TRCMODE=AUTO).

Sending this command to edit both TACC and any other attribute(s) will return the "Parameters Not Compatible" error message.

Sending this command to edit TACC on an AID with cross-connects will return the "VC in Use" error message.

This command is allowed to edit EXPTRC on STM1, STM16AS, and STM64 cards.


NoteTACC creation will be denied on protect ports and cards in 1:1, 1:N, and 1+1 configurations.

The VFAC AID is only valid on slots containing an ML-Series card. TACC is not supported for the ML-Series cards.

After the MS-SPRing switching, provisioning of the J1 trace string or trace mode is not allowed on the protection path.

TACC creation is allowed on protection channel access (PCA) for two-fiber and four-fiber MS-SPRing.

TACC is not supported on G1000, MXP_2.5_10G, TXP_MR_10G, ML1000-2, and ML100T-12 cards.

TACC is not supported on E3 and T3 ports in the Cisco ONS 15310 MA SDH platform.

HOLDOFFTIMER is not specific to a path. It is applicable to the SNCP selector. If HOLDOFFTIMER is changed on one path associated with the selector, the HOLDOFFTIMER of the other path associated with the same selector is also changed.

The cross-connects on the DS3i-N-12 card are VC4 width, but the individual VC1s within the 3C will be accessible. For editing the path attributes, use ED-VC3 with the FAC AID. For test access creation, use ED-VC4 because the test access path width (like the cross-connect) has to be 3C on the DS3i-N-12 card, which creates a new entity (TAP) on the DS3i-N-12 card in 3C width. On the DS3i-N-12 card, the ED-VC command can be used either with VC3 or VC4 modifier depending on the parameter to be modified.


Category

Paths

Security

Provisioning

Input Format

ED-<MOD_PATH>:[TID]:<AID>:[CTAG]:::[SFBER=<SFBER>],[SDBER=<SDBER>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[HOLDOFFTIMER=<HOLDOFFTIMER>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>],
[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-VC3:FERNDALE:VC3-1-1-1:115:::SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
TRCMODE=OFF,TACC=8,TAPTYPE=SINGLE,CMDMDE=NORM:UNLOCKED,
AUTOMATICINSERVICE;

Cisco ONS 15310 MA SDH

ED-VC3::VC3-3-1-1-1-1:31:::SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=8.0,EXPTRC="EXPTRCSTRING",CMDMDE=NORM:UNLOCKED,
AUTOMATICINSERVICE;

Table 11-5 ED-<MOD_PATH> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "CrossConnectId1" section.

Y

Y

Y

<SFBER>

(Optional) Signal failure threshold. Applies only to SNCP. Applies to VC4-level paths. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

Y

Y

Y

1E-3

SFBER is 1E-3.

Y

Y

Y

1E-4

SFBER is 1E-4.

Y

Y

Y

1E-5

SFBER is 1E-5.

Y

Y

Y

<SDBER>

(Optional) Signal degrade threshold. Applies only to SNCP. Applies to VC4-level paths (VCn). The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

Y

Y

Y

1E-5

SDBER is 1E-5.

Y

Y

Y

1E-6

SDBER is 1E-6.

Y

Y

Y

1E-7

SDBER is 1E-7.

Y

Y

Y

1E-8

SDBER is 1E-8.

Y

Y

Y

1E-9

SDBER is 1E-9.

Y

Y

Y

<RVRTV>

(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to SNCP. The parameter type is ON_OFF, which disables or enables an attribute.

Y

Y

Y

N

Does not revert service to original line after restoration.

Y

Y

Y

Y

Reverts service to original line after restoration.

Y

Y

Y

<RVTM>

(Optional) Revertive time. RVTM is not allowed to be set while RVRTV is N. Only applies to SNCP. The parameter type is REVERTIVE_TIME (revertive time).

Y

Y

Y

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

Y

Y

Y

N

Disable an attribute.

Y

Y

N

Y

Enable an attribute.

Y

Y

N

<HOLDOFFTIMER>

(Optional) Hold-off timer for SNCP DRI. Values must be within 0 and 10000 milliseconds (0 to 10 seconds), with increments of 100 milliseconds. HOLDOFFTIMER is an integer.

Y

Y

Y

<EXPTRC>

(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR and LF. Applicable to VC-level paths in SDH (VCn). EXPTRC is a string.

Y

Y

Y

<TRC>

(Optional) The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. A null value defaults to the NE transmitting null characters (Hex 00). Applicable to VC-level paths in SDH (VCn). TRC is a string.

Y

Y

Y

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level paths in SDH (VCn). Defaults to the OFF mode. The parameter type is TRCMODE (trace mode).

Y

Y

Y

AUTO

Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.

Y

Y

Y

AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on alarm indication signal (AIS) and remote defect indication (RDI) if TIM-P is detected.

Y

Y

Y

MAN

Use the provisioned expected string as the expected string.

Y

Y

Y

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

Y

Y

Y

OFF

Turn off path trace capability. Nothing will be reported.

Y

Y

Y

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.

Y

Y

Y

<TAPTYPE>

(Optional) TAP type. the parameter type is TAPTYPE (test access point type).

Y

Y

Y

DUAL

Dual FAD

Y

Y

Y

SINGLE

Single FAD

Y

Y

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

Y

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

Y

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

Y

Y

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

Y

Y

Unlocked

In service

Y

Y

Y

Locked

Out of service

Y

Y

Y

<SST>

(Optional) Secondary state. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

Y

Y

AutomaticInService

Automatic in service

Y

Y

Y

Disabled

Disabled

Y

Y

Y

Loopback

Loopback

Y

Y

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

Y

Y

Maintenance

Maintenance mode

Y

Y

Y

OutOfGroup

Out of group

Y

Y

Y

SoftwareDownload

Software downloading

Y

Y

Y

Unassigned

Unassigned

Y

Y

Y

NotInstalled

Unequipped

Y

Y

Y


11.6  ED-<MOD_RING>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Edit Multiplex Section-Shared Protection Ring (ED-<MOD_RING>) command edits the MS-SPRing attributes.

Usage Guidelines

The RVRTV, RVTM, SRVRTV, SRVTM, NODEID, and RINGID attributes can be edited for the four-fiber MS-SPRing.

The RVRTV, RVTM, NODEID, and RINGID attributes can be edited for the two-fiber MS-SPRing.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

The following actions will produce errors:

If the system fails on getting IOR, a SROF (Get IOR Failed) error message is returned

If the AID is invalid, an IIAC (Invalid AID) error message is returned.

If the MS-SPRing does not exist, a SRQN (MSSPR Does Not Exist) error message is returned.

The SROF (Facility Not Provisioned) or SROF (Cannot Access MSSPR) error message will be returned for an invalid query.

The SRQN (MSSPR Edition Failed) error message is returned for an invalid edition query.

Sending this command to modify SRVRTV or SRVTM on a two-fiber MS-SPRing will return an IDNV (Invalid Data For 2F-MS-SPRing) error message.

Sending this command to modify the node ID with invalid data will return an IIAC (Invalid NodeId) error message.

Sending this command to change the ring ID into invalid data will return an IIAC (Invalid RingId) error message.

Changing the MS-SPRing node ID with a duplicated ID will return a SROF (Cannot Set NodeId) error message.

Changing the MS-SPRing ring ID with a duplicated ID will return a SROF (Cannot Set RingId) error message.


NoteThe ALL AID is invalid for this command.

The list AID format is supported in Release 4.6 and later.


Category

MS-SPRing

Security

Provisioning

Input Format

ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>][:];

Input Example

ED-BLSR:PETALUMA:MSSPR-43:123:::RINGID=43,NODEID=3,RVRTV=Y,RVTM=2.0,
SRVRTV=Y,SRVTM=5.0;

Table 11-6 ED-<MOD_RING> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE. ALL or MSSPR-ALL AID is not allowed for editing an MS-SPRing.

Y

Y

N/A

<RINGID>

The MS-SPRing ID of the NE, up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.

Y

Y

N/A

<NODEID>

The MS-SPRing node ID of the NE. NODEID ranges from 0 to 31. NODEID is an integer.

Y

Y

N/A

<RVRTV>

Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

Y

Y

N/A

N

Does not revert service to original line after restoration.

Y

Y

N/A

Y

Reverts service to original line after restoration.

Y

Y

N/A

RVTM

Revertive time. RVTM is not allowed to be set while "RVRTV" is N. the parameter type is REVERTIVE_TIME (revertive time).

Y

Y

N/A

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

Y

Y

N/A

<SRVRTV>

The span revertive mode for four-fiber MS-SPRing only. The parameter type is ON_OFF (disable or enable an attribute).

Y

Y

N/A

N

Disable an attribute.

Y

Y

N/A

Y

Enable an attribute.

Y

Y

N/A

<SRVTM>

The span revertive time for four-fiber MS-SPRing only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).

Y

Y

N/A

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

Y

Y

N/A


11.7  ED-<STM_TYPE>

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit STM1, STM4, STM16, or STM64 command edits the attributes (for example, service parameters) and state of an STM facility. Allowable states for a facility are Locked, Locked with Automatic In Service transitioning, Locked for Maintenance, and Unlocked. See Table 27-1 for supported modifiers by platform.


Note The STM64 modifier is not supported on the Cisco ONS 15310 MA SDH platform.


Usage Guidelines

The OPRNOMINAL parameter is supported only by optical card types that support Optical PM. The following cards support OPRNOMINAL: STM1-8, MRC-12, MRC-12-2.5G, MRC-4-2.5G, STM64-XFP, CTX-2500, CTX, STM64-4, STM16-16, STM64-4-DWDM, ASAP-4.

The data communications channel (DCC) transmit is bridged to both working and protect in a 1+1 configuration. On the receive side, the active one is selected for DCC. The DCC is provisioned on the working port only in a 1+1 configuration.

All lines in a 1+1 MS-SPRing must have the same mode. If you change the mode of a line that is in a 1+1 MS-SPRing, an error message will be returned.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

You cannot directly transition a facility from IS to Locked-Disabled,DSBLD service state. You can transition a facility to Locked-Disabled, DSBLD service state from any state except Locked-Disabled, Maintenance. To transition a facility from Locked-Disabled, Maintenance to Locked-Disabled, DSBLD service state, all the following conditions must be met:

The facility is not sourcing a synchronization clock

The facility's DCC is disabled

The facility is not part of a protection group

The facility is not supporting cross-connects

The facility is not using overhead connections or overhead terminations (such as express orderwire, local orderwire, or user data channels [UDCs])


Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service (except for IS to Locked-Disabled, DSBLD transition) with no consideration for orderly interruption.


Category

Ports

Security

Provisioning

Input Format

ED-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>],[AREA=<AREA>],
[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[MUX=<MUX>],
[SOAK=<SOAK>],[OSPF=<OSPF>],[MSDCC=<MSDCC>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>],[SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>],[FOREIGNIP=<FOREIGNIP>],OPRNOMINAL=<OPRNOMINAL>]:[<PST>[,<SST>]];

Input Example

ED-STM16:PENNGROVE:FAC-6-1:114:::DCC=Y,AREA=10.92.63.1,SYNCMSG=N,SENDDUS=N,
PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,MUX=E2,SOAK=10,OSPF=Y,
MSDCC=N,NAME="STMPORT",CMDMDE=NORM,EXPTRC="AAA",TRC="AAA",
TRCMODE=MAN,TRCFORMAT=16-BYTE,ADMSSM=G811,SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=N,
FOREIGNIP="IPADDRESS",OPRNOMINAL=Y:UNLOCKED,AUTOMATICINSERVICE;

Cisco ONS 15310 MA SDH

ED-STM1::STM1-3-1-1:26:::DCC=N,SYNCMSG=N,SENDDUS=N,SFBER=1E-4,SDBER=1E-6,MODE=SDH:unlocked;

Table 11-7 ED-STM1 Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

Y

Y

<DCC>

(Optional) Indicates whether or not the RS-DCC is to be used. Identifies the RS-DCC connection of the port. The parameter type is ON_OFF (disable or enable an attribute).

Y

Y

Y

N

Disable an attribute.

Y

Y

Y

Y

Enable an attribute.

Y

Y

Y

<AREA>

(Optional) The area ID shows up only if the DCC is enabled.

Y

Y

Y

<SYNCMSG>

(Optional) Synchronization status message. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

Y

Y

Y

N

The ring does not support the extended K1/K2/K3 protocol.

Y

Y

Y

Y

The ring does support the extended K1/K2/K3 protocol.

Y

Y

Y

<SENDDUS>

(Optional) Whether the facility will send the Do Not Use for Synchronization (DUS) value as the synchronization status message for that facility. The parameter type is ON_OFF (disable or enable an attribute).

Y

Y

Y

N

Disable an attribute.

Y

Y

Y

Y

Enable an attribute.

Y

Y

Y

<PJMON>

(Optional) Identifies an STM port PJMON. PJMON is an integer. Set a valid VC4 number of the optical port.

Note The PJMON number displayed in TL1 interface does not correspond to the PJVC4MON number in CTC, but instead corresponds to the VC4 number of the optical port.

Y

Y

Y

<SFBER>

(Optional) Signal failure threshold. the parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

Y

Y

Y

1E-3

SFBER is 1E-3.

Y

Y

Y

1E-4

SFBER is 1E-4.

Y

Y

Y

1E-5

SFBER is 1E-5.

Y

Y

Y

<SDBER>

(Optional) Signal degrade threshold. the parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

Y

Y

Y

1E-5

SDBER is 1E-5

Y

Y

Y

1E-6

SDBER is 1E-6

Y

Y

Y

1E-7

SDBER is 1E-7

Y

Y

Y

1E-8

SDBER is 1E-8

Y

Y

Y

1E-9

SDBER is 1E-9

Y

Y

Y

<MODE>

(Optional) STM port mode. The parameter type is OPTICAL_MODE, which is the facility's optical mode.

Y

Y

Y

SINGLESHELF

The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.

Y

Y

Y

MULTISHELF

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.

Y

Y

N

MULTISHELFETH

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.

Y

Y

N

<MUX>

(Optional) MS-SPRing extension byte (supported only on the STM16AS card). The parameter type is MUX_TYPE, which is the MS-SPRing extension type.

Y

Y

N

E2

E2 byte (orderwire)

Y

Y

N

F1

F1 byte (user)

Y

Y

N

K3

K3 byte

Y

Y

N

Z2

Z2 byte

Y

Y

N

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

Y

Y

Y

<OSFP>

(Optional) The Open Shortest Path First discovery. The parameter type is ON_OFF (disable or enable an attribute).

Y

Y

Y

N

Disable an attribute.

Y

Y

Y

Y

Enable an attribute.

Y

Y

Y

<MSDCC>

(Optional) The MS-DCC connection on the port. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

Y

Y

Y

N

The ring does not support the extended K1/K2/K3 protocol.

Y

Y

Y

Y

The ring does support the extended K1/K2/K3 protocol.

Y

Y

Y

<NAME>

(Optional) NAME is a user-specified string to identify the facility.

Y

Y

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

Y

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

Y

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

Y

Y

<EXPTRC>

(Optional) Expected section trace content. Indicates the expected section trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). String data type.

Y

Y

Y

<TRC>

(Optional) The section trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. Defaults to NULL. TRC is a string.

Y

Y

Y

<TRCMODE>

(Optional) Section trace mode. Applicable only to VC-level paths in SDH (VCn). Defaults to the MAN mode. The parameter type is TRCMODE (trace mode).

Y

Y

Y

AUTO

Use the previously received section trace string as the expected string. Not applicable to MXP/TXP cards.

Y

Y

Y

AUTO-NO-AIS

Use the previously received section trace string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

Y

Y

Y

MAN

Use the provisioned expected string as the expected string.

Y

Y

Y

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

Y

Y

Y

OFF

Turn off section trace capability. Nothing will be reported.

Y

Y

Y

<TRCFORMAT>

(Optional) Trace message size. The parameter type is TRCFORMAT (trace format).

Y

Y

Y

1-BYTE

1 byte trace message

Y

Y

Y

16-BYTE

16 byte trace message

Y

Y

Y

64-BYTE

64 byte trace message

Y

Y

Y

<ADMSSM>

(Optional) SSM selectable value. It will only appear when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

Y

Y

Y

DUS_SDH

Do Not Use For Synchronization

Y

Y

Y

G811

G811 Standard

Y

Y

Y

RES_SDH

Reserved For Network Synchronization Use

Y

Y

Y

G812T

G812T Standard

Y

Y

Y

STU_SDH

Synchronized, Traceability Unknown

Y

Y

Y

G812TL

G812TL Standard

Y

Y

Y

SETS

Synchronous Equipment Timing Source

Y

Y

Y

<SENDDUSFF>

(Optional) The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.

Y

Y

Y

N

The ring does not support the extended K1/K2/K3 protocol.

Y

Y

Y

Y

The ring does support the extended K1/K2/K3 protocol.

Y

Y

Y

<AISONLPBK>

(Optional) The parameter type is AIS_ON_LPBK, which indicates if AIS should be sent on loopback.

Y

Y

Y

AIS_ONLPBK_FACILITY

AIS is sent on facility loopback.

Y

Y

Y

AIS_ON_LPBK_ALL

AIS is sent on all loopbacks.

Y

Y

Y

AIS_ON_LPBK_OFF

AIS is not sent on loopback.

Y

Y

Y

AIS_ON_LPBK_TERMINAL

AIS is sent on terminal loopback.

Y

Y

Y

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN (optical wavelength).

Y

Y

Y

1310

Wavelength 1310

Y

Y

Y

1470

Wavelength 1470

Y

Y

Y

1490

Wavelength 1490

Y

Y

Y

1510

Wavelength 1510

Y

Y

Y

1529.55

Wavelength 1529.55

Y

Y

Y

1529.94

Wavelength 1529.94

Y

Y

Y

1530

Wavelength 1530

Y

Y

Y

1530.33

Wavelength 1530.33

Y

Y

Y

1530.73

Wavelength 1530.73

Y

Y

Y

1531.12

Wavelength 1531.12

Y

Y

Y

1531.51

Wavelength 1531.51

Y

Y

Y

1531.90

Wavelength 1531.90

Y

Y

Y

1532.29

Wavelength 1532.29

Y

Y

Y

1532.68

Wavelength 1532.68

Y

Y

Y

1533.07

Wavelength 1533.07

Y

Y

Y

1533.47

Wavelength 1533.47

Y

Y

Y

1533.86

Wavelength 1533.86

Y

Y

Y

1534.25

Wavelength 1534.25

Y

Y

Y

1534.64

Wavelength 1534.64

Y

Y

Y

1535.04

Wavelength 1535.04

Y

Y

Y

1535.43

Wavelength 1535.43

Y

Y

Y

1535.82

Wavelength 1535.82

Y

Y

Y

1536.22

Wavelength 1536.22

Y

Y

Y

1536.61

Wavelength 1536.61

Y

Y

Y

1537

Wavelength 1537

Y

Y

Y

1537.40

Wavelength 1537.40

Y

Y

Y

1537.79

Wavelength 1537.79

Y

Y

Y

1538.19

Wavelength 1538.19

Y

Y

Y

1538.58

Wavelength 1538.58

Y

Y

Y

1538.98

Wavelength 1538.98

Y

Y

Y

1539.37

Wavelength 1539.37

Y

Y

Y

1539.77

Wavelength 1539.77

Y

Y

Y

1540.16

Wavelength 1540.16

Y

Y

Y

1540.56

Wavelength 1540.56

Y

Y

Y

1540.95

Wavelength 1540.95

Y

Y

Y

1541.35

Wavelength 1541.35

Y

Y

Y

1541.75

Wavelength 1541.75

Y

Y

Y

1542.14

Wavelength 1542.14

Y

Y

Y

1542.35

Wavelength 1542.35

Y

Y

Y

1542.54

Wavelength 1542.54

Y

Y

Y

1542.94

Wavelength 1542.94

Y

Y

Y

1543.33

Wavelength 1543.33

Y

Y

Y

1543.73

Wavelength 1543.73

Y

Y

Y

1544.13

Wavelength 1544.13

Y

Y

Y

1544.53

Wavelength 1544.53

Y

Y

Y

1544.92

Wavelength 1544.92

Y

Y

Y

1545.32

Wavelength 1545.32

Y

Y

Y

1545.72

Wavelength 1545.72

Y

Y

Y

1546.12

Wavelength 1546.12

Y

Y

Y

1546.52

Wavelength 1546.52

Y

Y

Y

1546.92

Wavelength 1546.92

Y

Y

Y

1547.32

Wavelength 1547.32

Y

Y

Y

1547.72

Wavelength 1547.72

Y

Y

Y

1548.12

Wavelength 1548.12

Y

Y

Y

1548.51

Wavelength 1548.51

Y

Y

Y

1548.92

Wavelength 1548.92

Y

Y

Y

1549.32

Wavelength 1549.32

Y

Y

Y

1549.71

Wavelength 1549.71

Y

Y

Y

1550

Wavelength 1500

Y

Y

Y

1550.12

Wavelength 1550.12

Y

Y

Y

1550.52

Wavelength 1550.52

Y

Y

Y

1550.92

Wavelength 1550.92

Y

Y

Y

1551.32

Wavelength 1551.32

Y

Y

Y

1551.72

Wavelength 1551.72

Y

Y

Y

1552.12

Wavelength 1552.12

Y

Y

Y

1552.52

Wavelength 1552.52

Y

Y

Y

1552.93

Wavelength 1552.93

Y

Y

Y

1553.33

Wavelength 1553.33

Y

Y

Y

1553.73

Wavelength 1553.73

Y

Y

Y

1554.13

Wavelength 1554.13

Y

Y

Y

1554.13

Wavelength 1554.13

Y

Y

Y

1554.94

Wavelength 1554.94

Y

Y

Y

1555.34

Wavelength 1555.34

Y

Y

Y

1555.75

Wavelength 1555.75

Y

Y

Y

1556.15

Wavelength 1556.15

Y

Y

Y

1556.55

Wavelength 1556.55

Y

Y

Y

1556.96

Wavelength 1556.96

Y

Y

Y

1557.36

Wavelength 1557.36

Y

Y

Y

1557.77

Wavelength 1557.77

Y

Y

Y

1558.17

Wavelength 1558.17

Y

Y

Y

1558.58

Wavelength 1558.58

Y

Y

Y

1558.98

Wavelength 1558.98

Y

Y

Y

1559.39

Wavelength 1559.39

Y

Y

Y

1559.79

Wavelength 1559.79

Y

Y

Y

1560.20

Wavelength 1560.20

Y

Y

Y

1560.61

Wavelength 1560.61

Y

Y

Y

1561.01

Wavelength 1561.01

Y

Y

Y

1561.42

Wavelength 1561.42

Y

Y

Y

1561.83

Wavelength 1561.83

Y

Y

Y

1570

Wavelength 1570

Y

Y

Y

1570.83

Wavelength 1570.83

Y

Y

Y

1571.24

Wavelength 1571.24

Y

Y

Y

1571.65

Wavelength 1571.65

Y

Y

Y

1572.06

Wavelength 1572.06

Y

Y

Y

1572.48

Wavelength 1572.48

Y

Y

Y

1572.89

Wavelength 1572.89

Y

Y

Y

1573.30

Wavelength 1573.30

Y

Y

Y

1573.71

Wavelength 1573.71

Y

Y

Y

1574.13

Wavelength 1574.13

Y

Y

Y

1574.54

Wavelength 1574.54

Y

Y

Y

1574.95

Wavelength 1574.95

Y

Y

Y

1575.37

Wavelength 1575.37

Y

Y

Y

1575.78

Wavelength 1575.78

Y

Y

Y

1576.20

Wavelength 1576.20

Y

Y

Y

1576.61

Wavelength 1576.61

Y

Y

Y

1577.03

Wavelength 1577.03

Y

Y

Y

1577.44

Wavelength 1577.44

Y

Y

Y

1577.86

Wavelength 1577.86

Y

Y

Y

1578.27

Wavelength 1578.27

Y

Y

Y

1578.69

Wavelength 1578.69

Y

Y

Y

1579.10

Wavelength 1579.10

Y

Y

Y

1579.52

Wavelength 1579.52

Y

Y

Y

1579.93

Wavelength 1579.93

Y

Y

Y

1580.35

Wavelength 1580.35

Y

Y

Y

1580.77

Wavelength 1580.77

Y

Y

Y

1581.18

Wavelength 1581.18

Y

Y

Y

1581.60

Wavelength 1581.60

Y

Y

Y

1582.02

Wavelength 1582.02

Y

Y

Y

1582.44

Wavelength 1582.44

Y

Y

Y

1582.85

Wavelength 1582.85

Y

Y

Y

1583.27

Wavelength 1583.27

Y

Y

Y

1583.69

Wavelength 1583.69

Y

Y

Y

1584.11

Wavelength 1584.11

Y

Y

Y

1584.53

Wavelength 1584.53

Y

Y

Y

1584.95

Wavelength 1584.95

Y

Y

Y

1585.36

Wavelength 1585.36

Y

Y

Y

1585.78

Wavelength 1585.78

Y

Y

Y

1586.20

Wavelength 1586.20

Y

Y

Y

1586.62

Wavelength 1586.62

Y

Y

Y

1587.04

Wavelength 1587.04

Y

Y

Y

1587.46

Wavelength 1587.46

Y

Y

Y

1587.88

Wavelength 1587.88

Y

Y

Y

1588.30

Wavelength 1588.30

Y

Y

Y

1588.73

Wavelength 1588.73

Y

Y

Y

1589.15

Wavelength 1589.15

Y

Y

Y

1589.57

Wavelength 1589.57

Y

Y

Y

1589.99

Wavelength 1589.99

Y

Y

Y

1590

Wavelength 1590

Y

Y

Y

1590.41

Wavelength 1590.41

Y

Y

Y

1590.83

Wavelength 1590.83

Y

Y

Y

1591.26

Wavelength 1591.26

Y

Y

Y

1591.68

Wavelength 1591.68

Y

Y

Y

1592.10

Wavelength 1592.10

Y

Y

Y

1592.52

Wavelength 1592.52

Y

Y

Y

1592.95

Wavelength 1592.95

Y

Y

Y

1593.37

Wavelength 1593.37

Y

Y

Y

1593.79

Wavelength 1593.79

Y

Y

Y

1594.22

Wavelength 1594.22

Y

Y

Y

1594.64

Wavelength 1594.64

Y

Y

Y

1595.06

Wavelength 1595.06

Y

Y

Y

1595.49

Wavelength 1595.49

Y

Y

Y

1596.34

Wavelength 1596.34

Y

Y

Y

1596.76

Wavelength 1596.76

Y

Y

Y

1597.19

Wavelength 1597.19

Y

Y

Y

1597.62

Wavelength 1597.62

Y

Y

Y

1598.04

Wavelength 1598.04

Y

Y

Y

1598.47

Wavelength 1598.47

Y

Y

Y

1598.89

Wavelength 1598.89

Y

Y

Y

1599.32

Wavelength 1599.32

Y

Y

Y

1599.75

Wavelength 1599.75

Y

Y

Y

1600.06

Wavelength 1600.06

Y

Y

Y

1601.03

Wavelength 1601.03

Y

Y

Y

1601.46

Wavelength 1601.46

Y

Y

Y

1601.88

Wavelength 1601.88

Y

Y

Y

1602.31

Wavelength 1602.31

Y

Y

Y

1602.74

Wavelength 1602.74

Y

Y

Y

1603.17

Wavelength 1603.17

Y

Y

Y

1603.60

Wavelength 1603.60

Y

Y

Y

1604.03

Wavelength 1604.03

Y

Y

Y

1610

Wavelength 1610

Y

Y

Y

USE-TWL1

Use Tunable Wavelength 1

Y

Y

Y

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

Y

Y

Y

AUTOPROV

Autoprovisioning

Y

Y

N

CX

Reach CX

Y

Y

N

DX

Reach DX

Y

Y

N

HX

Reach HX

Y

Y

N

I1

Reach I1

Y

Y

Y

IR-1

Reach IR-1

Y

Y

N

IR-2

Reach IR-2

Y

Y

N

L1

Reach L1

Y

Y

Y

L2

Reach L2

Y

Y

Y

L3

Reach L3

Y

Y

Y

LR-1

Reach LR-1

Y

Y

N

LR-2

Reach LR-2

Y

Y

N

LR-3

Reach LR-3

Y

Y

N

LX

Reach LX

Y

Y

N

S1

Reach S1

Y

Y

Y

S2

Reach S2

Y

Y

Y

SR

Reach SR

Y

Y

N

SR-1

Reach SR-1

Y

Y

N

SX

Reach SX

Y

Y

N

T

Reach T

Y

Y

N

VX

Reach VX

Y

Y

N

ZX

Reach ZX

Y

Y

N

<FOREIGNFEND>

(Optional) Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF (disable or enabled an attribute).

Y

Y

Y

N

Disable an attribute.

Y

Y

Y

Y

Enable an attribute.

Y

Y

Y

<FOREIGNIP>

(Optional) The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGNIP is a string.

Y

Y

Y

<OPRNOMINAL

Reads the current raw optical receive power and sets the raw OPR value as the nominal optical receive power.

Y

Y

Y

N

Not Supported.

Y

Y

Y

Y

Sets the OPR.

Y

Y

Y

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

Y

Y

Unlocked

In service

Y

Y

Y

Locked

Out of service

Y

Y

Y

<SST>

(Optional) Secondary state. Defaults to AUTOMATICINSERVICE. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

Y

Y

AutomaticInService

Automatic in service

Y

Y

Y

Disabled

Disabled

Y

Y

Y

Loopback

Loopback

Y

Y

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

Y

Y

Maintenance

Maintenance mode

Y

Y

Y

OutOfGroup

Out of group

Y

Y

Y

SoftwareDownload

Software downloading

Y

Y

Y

Unassigned

Unassigned

Y

Y

Y

NotInstalled

Unequipped

Y

Y

Y


11.8  ED-ALS

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Automatic Laser Shutdown (ED-ALS) command is used to modify the automatic laser shutdown (ALS) attributes of an STM facility and all the facilities that support the ALS feature. For transponder and muxponder cards, this command is used to modify the ALS parameter of the STM16 and STM64 ports.

Usage Guidelines

None

Category

Ports

Security

Provisioning

Input Format

ED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],[ALSRCPW=<ALSRCPW>][:];

Input Example

Cisco ONS 15454 SDH and Cisco ONS 15600 SDH

ED-ALS:CISCO:FAC-4-1-1:1:::ALSMODE=AUTO,ALSRCINT=130,ALSRCPW=80.1;

Cisco ONS 15310 MA SDH

ED-ALS:CISCO:STM1-4-1-1:1:::ALSMODE=AUTO,ALSRCINT=130,ALSRCPW=80.1;

Table 11-8 ED-ALS Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<SRC>

Access identifier from the "AidUnionId" section.

Y

Y

Y

<ALSMODE>

(Optional) ALS is enabled or disabled. the parameter type is ALS_MODE, which is the working mode for automatic laser shutdown.

Y

Y

Y

AUTO

Automatic

Y

Y

Y

DISABLED

Disabled

Y

Y

Y

MAN

Manual

Y

Y

Y

MAN-RESTART

Manual restart for test

Y

Y

Y

<ALSRCINT>

(Optional) ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer.

Y

Y

Y

<ALSRCPW>

(Optional) ALS recovery pulse width. The range is 80.0 to 100.00 seconds, in increments of 100 ms. ALSRCPW is a float.

Y

Y

Y


11.9  ED-APC

(Cisco ONS 15454 SDH) The Edit Amplification Power Control (ED-APC) command is used to modify the APC application attributes. The default value for an optional parameter is the NE default value. The value might not be the current value for the parameter. Use a retrieve command to retrieve the current value.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

ED-APC[:<TID>]:<AID>:<CTAG>[::<ROLE>][:APCENABLE=<APCENABLE>][:];

Input Example

ED-APC:PENNGROVE:WDMSIDE-A:CTAG:::APCENABLE=N;

Table 11-9 ED-APC Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<WDMSIDE>

The AID is used to access the WDM side of an MSTP node.

Y

N/A

N/A

WDMSIDE-{UNKNOWN,A,B,C,D,E,F,G,H}

MSTP side identifier

Y

N/A

N/A

<ROLE>

The role the unit is playing in the protection group.

Y

N/A

N/A

PROT

The entity is the protection unit in the protection group.

Y

N/A

N/A

WORK

The entity is the working unit in the protection group.

Y

N/A

N/A

<APCENABLE>

(Optional) Enable/disable the APC application. Default is N. The parameter type is ON_OFF (disable or enable an attribute).

Y

N/A

N/A

N

Disable an attribute.

Y

N/A

N/A

Y

Enable an attribute.

Y

N/A

N/A


11.10  ED-BITS

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Building Integrated Timing Supply (ED-BITS) command edits the building integrated timing supply (BITS) reference attributes.

Usage Guidelines

The SYNC-BITS1 and SYNC-BITS2 AIDs can be used to set the BITS-OUT port state. For a BITS facility, 2 M, 64 K, and E1 are only applicable for Cisco ONS 15600 SDH. Similarily, for Cisco ONS 15310 MA SDH only 2M and E1 are applicable.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

Synchronization

Security

Provisioning

Input Format

Cisco ONS 15454 SDH

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[SABIT=<SABIT>] ,[LBO=<LBO>], [SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>], [BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>];

Cisco ONS 15600 SDH

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[SABIT=<SABIT>] ,[IMPEDANCE=<IMPEDANCE>],[LBO=<LBO>],[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<A ISTHRSHLD>],[BITSFAC=<BITSFAC>][:<PST>];

Cisco ONS 15310 MA SDH

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[SABIT=<SABIT>] ,[IMPEDANCE=<IMPEDANCE>],[LBO=<LBO>],[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<A ISTHRSHLD>],[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>];

Input Example

Cisco ONS 15454 SDH

ED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=E1-MF,SYNCMSG=N,
,SABIT=BYTE-5,BITSFAC=E1,ADMSSM=G811:UNLOCKED

Cisco ONS 15600 SDH

ED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=E1-MF,IMPEDANCE=120,SYNCMSG=N,
,SABIT=BYTE-5,BITSFAC=E1:UNLOCKED

Cisco ONS 15310 MA SDH

ED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=E1-MF,IMPEDANCE=120,SYNCMSG=N,
,SABIT=BYTE-5,BITSFAC=E1:UNLOCKED

Table 11-10 ED-BITS Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "BITS" section.

Y

Y

Y

<LINECDE>

(Optional) Line code. The parameter type is LINE_CODE (line code).

Y

Y

Y

AMI

Line code value is AMI.

Y

Y

Y

B8ZS

Line code value is bipolar with eight-zero substitution.

N

N

N

HDB3

Line Code HDB3. Only applicable to SDH E1 signal.

Y

Y

Y

<FMT>

(Optional) Digital signal frame format. Defaults to E1-MF. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.

Y

Y

Y

D4

Frame format is D4

N

N

N

E1-CRC

SDH E1 CRC frame format

Y

Y

Y

E1-CRCMF

SDH E1 CRCMF frame format

Y

Y

Y

E1-MF

SDH E1 MF frame

Y

Y

Y

E1-FRAME

SDH E1-frame format

Y

Y

Y

E1-UNFRAMED

SDH E1 unframed format

Y

Y

Y

ESF

Frame format is ESF

N

N

N

<IMPEDANCE>

(Optional) Impedance is the total opposition that a circuit presents to alternating current. The maximum power transfer that takes place from the source to load when the impedance match.

N

Y

Y

120 ohms

120 ohm termination

N

Y

Y

100 ohms

100 ohm termination

N

Y

Y

75 ohms

75 ohm termination

N

Y

Y

<LBO>

(Optional) Line buildout settings. BITS line buildout. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line buildout).

Y

Y

Y

0-133

BITS line buildout range is 0-133.

Y

Y

Y

134-266

BITS line buildout range is 134-266.

Y

Y

Y

267-399

BITS line buildout range is 267-399.

Y

Y

Y

400-533

BITS line buildout range is 400-533.

Y

Y

Y

534-655

BITS line buildout range is 534-655.

Y

Y

Y

<SYNCMSG>

(Optional) Indicates whether the BITS facility supports synchronization status message. Default is on (Y). The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.

Y

Y

Y

N

The ring does not support the extended K1/K2/K3 protocol.

Y

Y

Y

Y

The ring does support the extended K1/K2/K3 protocol.

Y

Y

Y

<AISTHRSHLD>

(Optional) Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

Y

Y

Y

DUS_SDH

Do Not Use For Synchronization

Y

Y

Y

G811

G811 Standard

Y

Y

Y

RES_SDH

Reserved For Network Synchronization Use

Y

Y

Y

G812T

G812T Standard

Y

Y

Y

STU_SDH

Synchronized, Traceability Unknown

Y

Y

Y

G812TL

G812TL Standard

Y

Y

Y

SETS

Synchronous Equipment Timing Source

Y

Y

Y

<SABIT>

(Optional) When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).

Y

Y

Y

BYTE-4

SABIT is BYTE-4.

Y

Y

Y

BYTE-5

SABIT is BYTE-5.

Y

Y

Y

BYTE-6

SABIT is BYTE-6.

Y

Y

Y

BYTE-7

SABIT is BYTE-7.

Y

Y

Y

BYTE-8

SABIT is BYTE-8.

Y

Y

Y

<BITSFAC>

(Optional) BITS facility settings. BITS-2 always inherits the value of BITS-1. The parameter type is BITS_FAC, which is the BITS facility rate.

Note 2 M, 64 K, and E1 are only applicable to ONS 15600 SDH.

Y

Y

Y

2 M

2 MHz rate

Y

Y

Y

64 K

64 K rate

Y

Y

N

6 M

6 MHz rate

Y

Y

N

E1

E1 rate

Y

Y

Y

<ADMSSM>

(Optional) SSM selectable. Only applicable to BITS-IN when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

Note Not applicable to ONS 15600 SDH.

Y

Y

Y

DUS_SDH

Do Not Use For Synchronization

Y

Y

Y

G811

G811 Standard

Y

Y

Y

RES_SDH

Reserved For Network Synchronization Use

Y

Y

Y

G812T

G812T Standard

Y

Y

Y

STU_SDH

Synchronized, Traceability Unknown

Y

Y

Y

G812TL

G812TL Standard

Y

Y

Y

SETS

Synchronous Equipment Timing Source

Y

Y

Y

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

Y

Y

Unlocked

In service

Y

Y

Y

Locked

Out of service

Y

Y

Y


11.11  ED-BULKROLL-<STM_TYPE>

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Bulkroll for STM4, STM64, STM1, and STM16 command edits information about the rolling of traffic from one endpoint to another without interrupting service. This uses the FORCE option to force a valid signal. The only parameters that can be edited are RMODE and FORCE. The time slots cannot be edited. Use ED-ROLL-<MOD_PATH> for single path level rolling. See Table 27-1 for supported modifiers by platform.


Note The STM64 modifier is not supported on the Cisco ONS 15310 MA SDH platform.


Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

ED-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RTOSTART=<RTOSTART>],
[RFROMEND=<RFROMEND>],[CMDMDE=<CMDMDE>];

Input Example

ED-BULKROLL-STM16:CISCO:FAC-1-1:1:::RFROMSTART=VC3-1-1-1,
RTOSTART=VC3-1-1-1,RFROMEND=VC3-1-1-1,CMDMDE=FRCD;

Cisco ONS 15310 MA SDH

ED-BULKROLL-STM16:CISCO:STM16-4-1:1:::RFROMSTART=VC3-4-1-1-1,
RTOSTART=VC3-4-1-1-2,RFROMEND=VC3-4-1-1-1,CMDMDE=FRCD;

Table 11-11 ED-ROLL-<MOD_PATH> Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<FROM>

One of the end points. Access identifier from the "FACILITY" section for line level rolling and bulk rolling. Must not be null.

Y

Y

Y

<RFROMSTART>

(Optional) The starting time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (VC or VC11).

Y

Y

Y

<RFROMEND>

(Optional) The ending time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (VC or VC11).

Y

Y

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

Y

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

Y

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

Y

Y


11.12  ED-BWP-ETH

This command is used to modify a Bandwidth Profile entry in BWP DB. The BWP DB is a collection of BWP used in a Network Element.

Usage Guidelines

Error conditions for deleting bandwidth profile can be:

Invalid AID. If the AID is invalid, an IIAC (Invalid AID) error message is returned.

The "ALL" AID is invalid for this command.

The BWP having the specified AID should be present in the node, that is, already been entered by ENT-BWP-ETH command.

Category

ETHERNET

Security

Provisioning

Input Format

ED-BWP-ETH:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],[CIR=<CIR>],[CBS=<CBS>],[PBS=<PBS>],[PIR=<PIR>],[CFMSTATE=<CFM_STATE>][:];

Input Example

ED-BWP-ETH:ROCKS:BWP-10000:1:::NAME="MyBWP",CIR=10,CBS=1M,PBS=1M,PIR=20,CFMSTATE=Y;

Input Parameters

Table 11-12 ED-BWP-ETH Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

This AID is used to access BWP.

Y

N

N

BWP-ALL

All aid for BWP.

Y

N

N

BWP-{1-10000}

Single AID for BWP. The valid identifiers ranges from 1 to 10000.

Y

N

N

<NAME>

The BWP name. BWP name is a String.

Y

N

N

<CIR>

Ingress committed information rate. This is a value between 0 and 100. Default value is - 100.

Y

N

N

<CBS>

Ingress committed burst bucket size.

Y

N

N

4K

4 Kbit bucket size

Y

N

N

8K

16 Kbit bucket size

Y

N

N

16K

32 Kbit bucket size

Y

N

N

32K

64 Kbit bucket size

Y

N

N

64K

128 Kbit bucket size

Y

N

N

128K

256 Kbit bucket size

Y

N

N

256K

512 Kbit bucket size

Y

N

N

512K

1 Mbit bucket size

Y

N

N

1M

2 Mbit bucket size

Y

N

N

2M

4 Mbit bucket size

Y

N

N

4M

8 Mbit bucket size

Y

N

N

8M

16 Mbit bucket size

Y

N

N

16M

16 Kbit bucket size

Y

N

N

<PBS>

Ingress peak burst bucket size

Y

N

N

4K

4 Kbit bucket size

Y

N

N

8K

8 Kbit bucket size

Y

N

N

16K

16 Kbit bucket size

Y

N

N

32K

32 Kbit bucket size

Y

N

N

64K

64 Kbit bucket size

Y

N

N

128K

128 Kbit bucket size

Y

N

N

256K

256 Kbit bucket size

Y

N

N

512K

512 Kbit bucket size

Y

N

N

1M

1 Mbit bucket size

Y

N

N

2M

2 Mbit bucket size

Y

N

N

4M

4 Mbit bucket size

Y

N

N

8M

8 Mbit bucket size

Y

N

N

16M

16 Mbit bucket size

Y

N

N

<PIR>

Peak information rate. This is a value between 0 and 100. Default value is - 100.

Y

N

N

<CFMSTATE>

Link Integrity status

Y

N

N

Y

Enabled

Y

N

N

N

Disabled

Y

N

N


11.13  ED-CMD-SECU

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Command Security (ED-CMD-SECU) command edits the command security level of a particular command.

Usage Guidelines

None

Category

Security

Security

Superuser

Input Format

ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;

Input Example

ED-CMD-SECU::INIT-REG:1::SUPER;

Table 11-13 ED-CMD-SECU Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier string. Identifies the entity in the NE to which the command pertains. It is the command verb along with verb modifier(s), as it currently exists. It can be a single command or a block of commands, where the block could include all commands. Only INIT-REG will be supported. AID is a string. It must not be null.

Y

Y

Y

<CAP>

Command access privilege. It must not be null. The parameter type is PRIVILEGE, which is the security level.

Y

Y

Y

PROV

Provision security level. 60 minutes of idle time.

Y

Y

Y

SUPER

Superuser security level. 15 minutes of idle time.

Y

Y

Y


11.14  ED-COS-ETH

(Cisco ONS 15454 SDH) The Edit Cost of Service Ethernet (ED-COS-ETH) command edits the egress parameter of a CoS table associated to an L2 Ethernet port.

Usage Guidelines

The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

Ethernet

Security

Provisioning

Input Format

ED-COS-ETH:[<TID>]:<AID>:<CTAG>:::[QOSENABLED=<QOSENABLED>],[BW0=<BWO>],
[WEIGHT0=<WEIGHT0>],[BW1=<BW1>],[WEIGHT1=<WEIGHT1>],[BW2=<BW2>],
[WEIGHT2=<WEIGHT2>],[BW3=<BW3>],[WEIGHT3=<WEIGHT3>],[BW4=<BW4>],
[WEIGHT4=<WEIGHT4>],[BW5=<BW5>],[WEIGHT5=<WEIGHT5>],[BW6=<BW6>],
[WEIGHT6=<WEIGHT6>],[BW7=<BW7>],[WEIGHT7=<WEIGHT7>][:];

Input Example

ED-COS-ETH:PETALUMA:ETH-1-1-1:1:::QOSENABLED=Y,BW0=10,WEIGHT0=0,BW1=20,
WEIGHT1=2,BW2=40,WEIGHT2=4,BW3=60,WEIGHT3=6,BW4=70,WEIGHT4=8,BW5=80,
WEIGHT5=10,BW6=85,WEIGHT6=12,BW7=100,WEIGHT7=15:;

Table 11-14 ED-COS-ETH Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the "FACILITY" section.

Y

N/A

N/A

<QOSENABLED>

Used to enable or disable the egress QOS policy of an L2 Ethernet port.

Y

N/A

N/A

N

Disable the service.

Y

N/A

N/A

Y

Enable the service.

Y

N/A

N/A

<BW0>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT0>

Value represents the weighted round-robin (WRR) weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW1>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT1>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW2>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT2>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW3>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT3>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW4>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT4>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW5>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT5>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW6>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT6>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A

<BW7>

Bandwidth percentage, a value between 0 and 100.

Y

N/A

N/A

<WEIGHT7>

Value represents the WRR weight associated to the COS values, an integer value between 0 and 15.

Y

N/A

N/A


11.15  ED-CRS-<PATH>

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Cross-Connection for VC3, VC44C, VC38C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (ED-CRS-<PATH>) command edits a cross-connect. See Table 27-1 for supported modifiers by platform.


Note The VC 11 and VC464C modifiers are not supported on the Cisco ONS 15310 MA SDH platform.


Usage Guidelines

ADD and REMOVE cannot be used together. The example provided is for informational purposes only. ADD and REMOVE are mutually exclusive.

Add/Remove drops is possible only on ONEWAY, SNCP_DROP, SNCP_DC, and SNCP_EN type of cross-connects (one-way only).

Traditional cross-connections cannot be upgraded to DRI cross-connections using the ED_CRS command.

CKTID is a string of ASCII characters. The maximum length of CKTID is 48. If the CKTID is EMPTY or NULL, this field will not appear.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

You cannot add or drop onto unidirectional connections on MS-SPRing DRI primary or secondary nodes.

Category

Cross Connections

Security

Provisioning

Input Format

ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]:[ADD=<ADD>],
[REMOVE=<REMOVE>],[CKTID=<CKTID>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-CRS-VC4::VC4-1-1-1,VC4-2-1-1:1:::ADD=VC4-13-1-1,REMOVE=VC4-2-1-1,CKTID=CKTID
CMDMDE=FRCD:UNLOCKED,AUTOMATICINSERVICE;

Cisco ONS 15310 MA SDH

ED-CRS-VC3::VC3-1-1-3,VC3-3-1-1-1-1:23:::ADD=VC3-3-2-1-1-1;

Table 11-15 ED-CRS-<PATH> Command- Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<SRC>

Source AID from the "CrossConnectId1" section.

Y

Y

Y

<DST>

Destination AID from the "CrossConnectId1" section.

Y

Y

Y

<CCT>

(Optional) Type of connection. Used for specifying one or two-way connections. The parameter type is CCT, which is the type of cross-connect to be created.

Y

Y

Y

1WAY

A unidirectional connection from a source tributary to a destination tributary

Y

Y

Y

1WAYDC

SNCP multicast drop (one-way continue)

Y

Y

Y

1WAYEN

SNCP multicast end node (one-way continue)

Y

Y

Y

1WAYMON

A bidirectional connection between the two tributaries

Note 1WAYMON is not supported with TL1. However, it is still supported from Cisco Transport Controller (CTC). Using CTC, you can create 1WAYMON cross-connects and can be retrieved through TL1.

Y

Y

Y

1WAYPCA

A unidirectional connection from a source tributary to a destination tributary on the protection path/fiber

Y

Y

N

2WAY

A bidirectional connection between the two tributaries

Y

Y

Y

2WAYDC

A bidirectional drop-and-continue connection applicable only to SNCP traditional and integrated DRIs

Y

Y

Y

2WAYPCA

A bidirectional connection between the two tributaries on the extra protection path/fiber

Y

Y

N

DIAG

Diagnostics cross-connect. Supports BERT (MS-SPRing PCA diagnostics cross-connect).

Y

Y

Y

<ADD>

(Optional) AID from the "AidUnionId" section.

Y

Y

Y

<REMOVE>

(Optional) AID from the "AidUnionId" section.

Y

Y

Y

<CKTID>

(Optional) Circuit identification that contains the common language Circuit ID or other alias of the circuit being provisioned. Cannot contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

Y

Y

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

Y

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

Y

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

Y

Y

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

Y

Y

Unlocked

In service

Y

Y

Y

Locked

Out of service

Y

Y

Y

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

Y

Y

AutomaticInService

Automatic in service

Y

Y

Y

Disabled

Disabled

Y

Y

Y

Loopback

Loopback

Y

Y

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

Y

Y

Maintenance

Maintenance mode

Y

Y

Y

OutOfGroup

Out of group

Y

Y

Y

SoftwareDownload

Software downloading

Y

Y

Y

Unassigned

Unassigned

Y

Y

Y

NotInstalled

Unequipped

Y

Y

Y


11.16  ED-CRS-ETH

This command modifies an ethernet connection relationship between two or more ethernet connection end points inside the ethernet facilities.

Usage Guidelines

The default values for all optional parameters are NE default values. These values may not be the current value for a parameter. In order to obtain the current value use RTRV-XX command to retrieve them.

The ethernet connection end point identifier must be the same for all the ethernet ports inside the connection and must be kept the same for all the ethernet cirtuit.

CKTID is a string of ASCII characters. The maximum length of CKTID can be 48. If the CKTID is EMPTY or NULL this field is not displayed

If the AID is invalid, an IIAC (Invalid AID) error message is returned.

The "ALL" AID is invalid for this command.

Category

ETHERNET

Security

Provisioning

Input Format

ED-CRS-ETH:[<TID>]:<SRC>,<DST>:<CTAG>:::[ADD=<ADD>],[REMOVE=<REMOVE>],[CKTID=<CKTID>][:];

Input Example

ED-CRS-ETH:KARTHIK:ETH-1-1-1-12,ETH-1-21-1-12:1:::CKTID=NEW,ADD=ETH-1-2-1;

Table 11-16 ED-CRS-ETH Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<SRC>

Ethernet connection identifier AIDs used to access L2 ethernet connection end point.

Y

N

N

ALL

The ALL aid is applicable for RTRV-only commands, basically the RTRV-rr type of commands.

Y

N

N

ETHID[-{1-12}]-{1-5,12-16}-{1-22}-1-{1-20}

Ethernet connection end point aid for GE-XP card.

Y

N

N

ETHID[-{1-12}]-{1-6,12-17}-{1-4}-1-{1-20}

Facility AID for 10GE-XP card.

Y

N

N

<DST>

Ethernet connection identifier AIDs are used to access L2 ethernet connection end point

Y

N

N

ALL

The ALL aid is applicable for RTRV-only commands, basically the RTRV-rr type of commands.

Y

N

N

ETHID[-{1-12}]-{1-5,12-16}-{1-22}-1-{1-20}

Ethernet connection end point aid for GE-XP card.

Y

N

N

ETHID[-{1-12}]-{1-6,12-17}-{1-4}-1-{1-20}

Facility aid for 10GE-XP card.

Y

N

N

<ADD>

The AID AidUnionId. Default value is - NULL

Y

N

N

<REMOVE>

The AID AidUnionId. Default value is - "NULL".

Y

N

N

<CKTID>

Circuit identification parameter contains the Common Language Circuit ID or other alias of the circuit being provisioned. Default value is - "NULL"

Y

N

N


11.17  ED-DAT

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Date and Time (ED-DAT) command edits the date and time.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>];

Input Example

ED-DAT:CISCO::1234::99-12-21,14-35-15;

Input Parameters

<DATE>

(Optional) Date. DATE is a string.

<TIME>

(Optional) Time. TIME is a string.


11.18  ED-DS3I

(Cisco ONS 15454 SDH) The Edit DS3I (ED-DS3I) command edits the attributes of a DS3i-N-12 facility.

Usage Guidelines

The following actions will return error messages:

Sending this command to edit TACC and any other attribute while the port has a cross-connection or the port/VT has a test access point (TAP or TACC Number) will return the IPNC (Parameters Not Compatible) error message.

Editing the TACC through the ED-xxx command is only allowed if there are no circuits or cross-connects on the port and the port or VT does not have a test access point (TAP or TACC Number). Otherwise, an error message will be returned.


NoteThis command is not allowed if the card is a protect card. TACC creation will be denied on protect ports/cards.

Automatic application of loopbacks originating from the far end can be inhibited on the ports of a DS3i-N-12 card.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.


You cannot directly transition a facility from IS to Locked-Disabled,DSBLD service state. You can transition a facility to Locked-Disabled,DSBLD service state from any state except Locked-Disabled,Maintenance. To transition a facility from Locked-Disabled,Maintenance to Locked-Disabled,DSBLD service state, all the following conditions must be met:

The facility is not sourcing a synchronization clock

The facility's DCC is disabled

The facility is not part of a protection group

The facility is not supporting cross-connects

The facility is not using overhead connections or overhead terminations (such as express orderwire, local orderwire, or user data channels [UDCs])


Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service (except for IS to Locked-Disabled,DSBLD transition) with no consideration for orderly interruption.


Category

Ports

Security

Provisioning

Input Format

ED-DS3I:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>],[LINECDE=<LINECDE>],[LBO=<LBO>],
[INHFELPBK=<INHFELPBK>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>],
[SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-DS3I:CISCO:FAC-1-2:1:::FMT=C-BIT,LINECDE=B8ZS,LBO=0-255,INHFELPBK=N,
TACC=8,TAPTYPE=SINGLE,SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="DS3I PORT",
CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Table 11-17 ED-DS3I Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

Y

Y

C-BIT

C-BIT line type applies to the DS3i-N-12 cards.

Y

Y

Y

M13

M13 line type applies to the DS3i-N-12 cards.

Y

Y

Y

UNFRAMED

Line type is unframed.

Y

Y

Y

<LINECDE>

(Optional) Line code. Defaults to B8ZS. The parameter type is DS_LINE_CODE.

Y

Y

Y

AMI

Line code value is AMI.

Y

Y

Y

B8ZS

Line code value is B8ZS.

Y

Y

Y

HDB3

Line code value is HDB3.

Y

Y

Y

<LBO>

(Optional) Line buildout settings. LBO is an integer. Defaults to 0-255. The parameter type is E_LBO, which is the electrical signal line buildout.

Y

Y

Y

0-225

Electrical signal line buildout range is 0-225.

Y

Y

Y

226-450

Electrical signal line buildout range is 226-450.

Y

Y

Y

<INHFELPBK>

(Optional) Far-end loopback inhibition attribute of the port. If it is Y, the automatic far-end loopbacks are inhibited. It is either on or off. Defaults to Y. The parameter type is ON_OFF (disable or enable an attribute).

Y

Y

Y

N

Disable an attribute.

Y

Y

Y

Y

Enable an attribute.

Y

Y

Y

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.

Y

Y

Y

<TAPTYPE>

(Optional) TAP type. The parameter type is TAPTYPE, which is the test access point type.

Y

Y

Y

DUAL

Dual FAD

Y

Y

Y

SINGLE

Single FAD

Y

Y

Y

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

Y

Y

Y

1E-3

SFBER is 1E-3.

Y

Y

Y

1E-4

SFBER is 1E-4.

Y

Y

Y

1E-5

SFBER is 1E-5.

Y

Y

Y

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

Y

Y

Y

1E-5

SDBER is 1E-5.

Y

Y

Y

1E-6

SDBER is 1E-6.

Y

Y

Y

1E-7

SDBER is 1E-7.

Y

Y

Y

1E-8

SDBER is 1E-8.

Y

Y

Y

1E-9

SDBER is 1E-9.

Y

Y

Y

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32. SOAK is an integer.

Y

Y

Y

<NAME>

(Optional) Maximum length is 32 characters. NAME is a string. Defaults to Null.

Y

Y

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

Y

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

Y

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

Y

Y

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

Y

Y

Unlocked

In service

Y

Y

Y

Locked

Out of service

Y

Y

Y

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

Y

Y

AutomaticInService

Automatic in service

Y

Y

Y

Disabled

Disabled

Y

Y

Y

Loopback

Loopback

Y

Y

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

Y

Y

Maintenance

Maintenance mode

Y

Y

Y

OutOfGroup

Out of group

Y

Y

Y

SoftwareDownload

Software downloading

Y

Y

Y

Unassigned

Not assigned

Y

Y

Y

NotInstalled

Unequipped

Y

Y

Y


11.19  ED-E1

(Cisco ONS 15454 SDH and Cisco ONS 15310 MA SDH) The Edit E1(ED-E1) command edits the attributes of an E1 facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Sending this command to edit TACC and any other attribute while the port has a cross-connect or the port/VT has a test access point (TAP or TACC Number), will return the IPNC (Parameters Not Compatible) error message.


Note TACC creation will be denied on the protect ports/cards.



Note ADMSSM, RETIME, SABIT, SYNCMSG, and SENDDUS parameters are supported on the DS1/E1-56, E1-21-DS3-E3-3, and E1-63-DS3-E3-3 on the Cisco ONS 15310 MA SDH platform.


You cannot directly transition a facility from IS to Locked-Disabled,DSBLD service state. You can transition a facility to Locked-Disabled,DSBLD service state from any state except Locked-Disabled,Maintenance. To transition a facility from Locked-Disabled,Maintenance to Locked-Disabled,DSBLD service state, all the following conditions must be met:

The facility is not sourcing a synchronization clock

The facility's DCC is disabled

The facility is not supporting cross-connects


Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service (except for IS to Locked-Disabled,DSBLD transition) with no consideration for orderly interruption.


Category

Ports

Security

Provisioning

Input Format

ED-E1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[TACC=<TACC>],
[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SYNCMSG=<SYNCMSG>],
[SENDDUS=<SENDDUS>],[RETIME=<RETIME>],[ADMSSM=<ADMSSM>],
[SABIT=<SABIT>]:[<PST>[,<SST>]];

Input Example

ED-E1:CISCO:FAC-2-1:1:::LINECDE=HDB3,FMT=E1-MF,TACC=8,TAPTYPE=SINGLE,
SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="E1 PORT",CMDMDE=NORM,
SYNCMSG=N,SENDDUS=N,RETIME=Y,ADMSSM=STU_SDH,
SABIT=BYTE-4:UNLOCKED,AUTOMATICINSERVICE;

Cisco ONS 15310 MA SDH

ED-E1::E1-1-1:1:::LINECDE=HDB3,FMT=E1-MF,SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="E1 PORT",CMDMDE=NORM, SYNCMSG=N,SENDDUS=N,RETIME=Y:UNLOCKED,AUTOMATICINSERVICE;

Table 11-18 ED-E1 Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

N/A

Y

<LINECDE>

(Optional) Line code. Defaults to HDB3. The parameter type is LINE_CODE (line code). (Applicable only for SDH platform).

Y

N/A

Y

AMI

Line code value is AMI.

Y

N/A

N

B8ZS

Line code value is B8ZS.

Y

N/A

N

HDB3

Line code value is HDB3. (Applicable only for SDH platform).

Y

N/A

Y

<FMT>

(Optional) Digital signal frame format. Defaults to E1-MF. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.

Y

N/A

N

D4

Frame format is D4

N

N/A

N

E1-CRCMF

SDH E1 CRCMF frame format

Y

N/A

Y

E1-MF

SDH E1 MF frame

Y

N/A

Y

E1-UNFRAMED

SDH E1 unframed format

Y

N/A

Y

ESF

Frame format is ESF

N

N/A

N

UNFRAMED

Frame format is unframed

N

N/A

N

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Default is N. TACC is an integer.

Y

N/A

Y

<TAPTYPE>

(Optional) TAP type. Defaults to DUAL. The parameter type is TAPTYPE, which is the test access point type.

Y

N/A

Y

DUAL

Dual FAD

Y

N/A

Y

SINGLE

Single FAD

Y

N/A

Y

1E-5

SDBER is 1E-5.

Y

N/A

Y

1E-6

SDBER is 1E-6.

Y

N/A

Y

1E-7

SDBER is 1E-7.

Y

N/A

Y

1E-8

SDBER is 1E-8.

Y

N/A

Y

1E-9

SDBER is 1E-9.

Y

N/A

Y

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32. SOAK is an integer.

Y

N/A

Y

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

Y

N/A

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

N/A

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

N/A

Y

<SYNCMSG>

(Optional) Synchronization status messaging is enabled or disabled on the E1 facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

Y

N/A

Y

N

No

Y

N/A

Y

Y

Yes

Y

N/A

Y

<SENDDUS>

(Optional) The facility will send the DUS value as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

Y

N/A

Y

N

No

Y

N/A

Y

Y

Yes

Y

N/A

Y

<RETIME>

(Optional) Indicates if retiming is needed. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

Y

N/A

Y ( Supported only on the

E1-21-DS3-E3-3 card on Cisco ONS 15310 MA SDH.

N

No

Y

N/A

Y

Y

Yes

Y

N/A

Y

<ADMSSM>

(Optional) The administrative synchronization status message. Defaults to STU_SDH. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level.

Y

N/A

Y

DUS

Do Not Use For Synchronization

Y

N/A

Y

PRS

Primary Reference Source, Stratum 1 Traceable

N

N/A

N

DUS_SDH

Do Not Use For Synchronization

Y

N/A

Y

G811

G811 Standard

Y

N/A

Y

G812T

G812T Standard

Y

N/A

Y

STU_SDH

Synchronized, Traceability Unknown

Y

N/A

Y

G812TL

G812TL Standard

Y

N/A

Y

SETS

Synchronous Equipment Timing Source

Y

N/A

Y

<SABIT>

(Optional) When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).

Y

N/A

Y

BYTE-4

SABIT is BYTE-4.

Y

N/A

Y

BYTE-5

SABIT is BYTE-5.

Y

N/A

Y

BYTE-6

SABIT is BYTE-6.

Y

N/A

Y

BYTE-7

SABIT is BYTE-7.

Y

N/A

Y

BYTE-8

SABIT is BYTE-8.

Y

N/A

Y

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

Y

Unlocked

In service

Y

N/A

Y

Locked

Out of service

Y

N/A

Y

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

Y

AutomaticInService

Automatic in service

Y

N/A

Y

Disabled

Disabled

Y

N/A

Y

Loopback

Loopback

Y

N/A

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

Y

Maintenance

Maintenance mode

Y

N/A

Y

OutOfGroup

Out of group

Y

N/A

Y

SoftwareDownload

Software downloading

Y

N/A

Y

Unassigned

Unassigned

Y

N/A

Y

NotInstalled

Unequipped

Y

N/A

Y


11.20  ED-E3

(Cisco ONS 15454 SDH and Cisco ONS 15310 MA SDH) The Edit E3 (ED-E3) command edits the attributes of an E3 facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Sending this command to edit TACC and any other attribute while the port has a cross-connect or the port or VT has a test access point (TAP or TACC Number) will return the IPNC (Parameters Not Compatible) error message.


Note TACC creation will be denied on the protect ports and cards.


You cannot directly transition a facility from IS to Locked-Disabled,DSBLD service state. You can transition a facility to Locked-Disabled,DSBLD service state from any state except Locked-Disabled,Maintenance. To transition a facility from Locked-Disabled,Maintenance to Locked-Disabled,DSBLD service state, all the following conditions must be met:

The facility is not sourcing a synchronization clock

The facility's DCC is disabled

The facility is not supporting cross-connects


Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service (except for IS to Locked-Disabled,DSBLD transition) with no consideration for orderly interruption.


Category

Ports

Security

Provisioning

Input Format

Cisco ONS 15454 and 15600

ED-E3:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Cisco ONS 15310 MA SDH

ED-E3:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>]:[<AISONLPBK=<AISONLPBK>]:[<PST>[,<SST>]];

Input Example

Cisco ONS 15454 and 15600 SDH

ED-E3:CISCO:E3-1-2:1:::TACC=8,TAPTYPE=SINGLE,SFBER=1E-4,SDBER=1E-6,SOAK=10,
NAME="E3 PORT",CMDMDE=CMDMDE, UNLOCKED,AUTOMATICINSERVICE;

Cisco ONS 15310 MA SDH

ED-E3::E3-1-1:1:::SFBER=1E-4,SDBER=1E-6,SOAK=10, NAME="E3 PORT",CMDMDE=FRCD,AISONLPBK=OFF:UNLOCKED,AUTOMATICINSERVICE;

Table 11-19 ED-E3 Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

N/A

Y

<AISONLPBK>

Indicates if the AutomaticInService should be sent back in loopback. (Applicable only for the

Cisco ONS 15310 MA SDH platform).

N

N/A

Y

FACILITY

Facility

N

N/A

Y

TERMINAL

Terminal

N

N/A

Y

OFF

Off

N

N/A

Y

ALL

All

N

N/A

Y

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Default is N. TACC is an integer.

Y

N/A

N

<TAPTYPE>

(Optional) TAP type. Defaults to DUAL. The parameter type is TAPTYPE, which is the test access point type.

Y

N/A

N

DUAL

Dual FAD

Y

N/A

N

SINGLE

Single FAD

Y

N/A

N

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

Y

N/A

Y

1E-3

SFBER is 1E-3.

Y

N/A

Y

1E-4

SFBER is 1E-4.

Y

N/A

Y

1E-5

SFBER is 1E-5.

Y

N/A

Y

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

Y

N/A

Y

1E-5

SDBER is 1E-5.

Y

N/A

Y

1E-6

SDBER is 1E-6.

Y

N/A

Y

1E-7

SDBER is 1E-7.

Y

N/A

Y

1E-8

SDBER is 1E-8.

Y

N/A

Y

1E-9

SDBER is 1E-9.

Y

N/A

Y

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals.Defaults to 32. SOAK is an integer.

Y

N/A

Y

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

Y

N/A

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

N/A

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

N/A

Y

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

Y

Unlocked

In service

Y

N/A

Y

Locked

Out of service

Y

N/A

Y

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

Y

AutomaticInService

Automatic in service

Y

N/A

Y

Disabled

Disabled

Y

N/A

Y

Loopback

Loopback

Y

N/A

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

Y

Maintenance

Maintenance mode

Y

N/A

Y

OutOfGroup

Out of group

Y

N/A

Y

SoftwareDownload

Software downloading

Y

N/A

Y

Unassigned

Unassigned

Y

N/A

Y

NotInstalled

Unequipped

Y

N/A

Y


11.21  ED-E4

(Cisco ONS 15454 SDH) The Edit E4 (ED-E4) command edits the attributes of an E4 facility. Currently this is only applicable to STM1E Ports 9 to 12 when they are in E4-FRAMED or E4-UNFRAMED mode.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

Ports

Security

Provisioning

Input Format

ED-E4:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-E4:CISCO1:FAC-6-1:114:::SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="E4 PORT",
CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Table 11-20 ED-E4 Command Parameter Support

Input Paramters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Access identifier from the "FACILITY" section.

Y

N/A

N/A

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

Y

N/A

N/A

1E-3

SFBER is 1E-3.

Y

N/A

N/A

1E-4

SFBER is 1E-4.

Y

N/A

N/A

1E-5

SFBER is 1E-5.

Y

N/A

N/A

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

Y

N/A

N/A

1E-5

SDBER is 1E-5.

Y

N/A

N/A

1E-6

SDBER is 1E-6.

Y

N/A

N/A

1E-7

SDBER is 1E-7.

Y

N/A

N/A

1E-8

SDBER is 1E-8.

Y

N/A

N/A

1E-9

SDBER is 1E-9.

Y

N/A

N/A

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals.Defaults to 32. SOAK is an integer.

Y

N/A

N/A

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

Y

N/A

N/A

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

N/A

FRCD

Force the system to override a state in which the command would normally be denied.

Y

N/A

N/A

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

N/A

N/A

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

N/A

Unlocked

In service

Y

N/A

N/A

Locked

Out of service

Y

N/A

N/A

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

N/A

AutomaticInService

Automatic in service

Y

N/A

N/A

Disabled

Disabled

Y

N/A

N/A

Loopback

Loopback

Y

N/A

N/A

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

N/A

Maintenance

Maintenance mode

Y

N/A

N/A

OutOfGroup

Out of group

Y

N/A

N/A

SoftwareDownload

Software downloading

Y

N/A

N/A

Unassigned

Unassigned

Y

N/A

N/A

NotInstalled

Unequipped

Y

N/A

N/A


11.22  ED-ETH

(Cisco ONS 15454 SDH and Cisco ONS 15310 MA SDH) The Edit Ethernet (ED-ETH) command edits the front-end port information of a 10/100/1000 Mbps Ethernet card.

Usage Guidelines

The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

SELECTIVEAUTO parameter is applicable only when EXPSPEED and EXPDUPLEX is not set to AUTO mode.


Note This command is available in Software Release 8.0.1 and later. It is not available in R8.0.0 and earlier.


Category

Ethernet

Security

Provisioning

Input Format

ED-ETH:[<TID>]:<AID>:<CTAG>:::[FLOW=<FLOW>],[EXPDUPLEX=<EXPDUPLEX>],[SELECTIVEAUTO=<SELECTIVEAUTO>],[EXPSPEED=<EXPSPEED>],[VLANCOS=<VLANCOSTHRESHOLD>],[IPTOS=<IPTOSTHRESHOLD>],[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SUPPRESS=<SUPPRESS>],[SOAK=<SOAK>],[LITIMER=<LITIMER>][:<PST>[,<SST>]];

Input Example

ED-ETH:CISCO:FAC-1-1:123:::FLOW=FLOW,EXPDUPLEX=EXPDUPLEX,
SELECTIVEAUTO=SELECTIVEAUTO, EXPSPEED=EXPSPEED,
VLANCOS=VLANCOS,IPTOS=IPTOS,NAME="ETHPORT",CMDMDE=CMDMDE,
SOAK=32,LITIMER=200:IS,AINS;

Cisco ONS 15310 MA SDH

ED-ETH:CISCO:ETH-1-1:123:::EXPDUPLEX=HALF,EXPSPEED=10_MBPS,SELECTIVEAUTO=Y;

Table 11-21 ED-ETH Command - Parameter Support

Input Parameters
Description
ONS 15454 SDH
ONS 15600 SDH
ONS 15310-MA SDH

<AID>

Ethernet AIDs are used to access L2 Ethernet ports. Access identifier from the "FACILITY" section.

Y

N/A

Y

<FACILITY>

Access identifier from the "FACILITY" section.

Y

N/A

Y

<FLOW

(Optional) Flow. The parameter type is ON_OFF (disable or enable an attribute).

Y

N/A

Y

N

Disable an attribute.

Y

N/A

Y

Y

Enable an attribute.

Y

N/A

Y

<EXPDUPLEX>

(Optional) Ethernet duplex mode. The parameter type is ETHER_DUPLEX, which is the duplex mode.

Y

N/A

Y

AUTO

Auto mode

Y

N/A

Y

FULL

Full mode

Y

N/A

Y

HALF

Half mode

Y

N/A

Y

<SELECTIVEAUTO>

(Optional) Selective auto-negotiation. The parameter is Y or N (enable or disable auto-negotiation) This indicates selective auto-negotiation of EXPSPEED and EXPDUPLEX only.

Y

N/A

Y

Y

Enable selective auto-negotiation.

Y

N/A

Y

N

Disable selective auto-negotiation.

Y

N/A

Y

<EXPSPEED>

(Optional) Ethernet speed. The parameter type is ETHER_SPEED, which is the Ethernet speed.

Y

N/A

Y

100_MBPS

100 Megabits per second

Y

N/A

Y

10_GBPS

10 Gigabits per second

Y

N/A

Y

10_MBPS

10 Megabits per second

Y

N/A

Y

1_GBPS

1 Gigabit per second

Y

N/A

Y

AUTO

Auto

Y

N/A

Y

<VLANCOS>

(Optional) Priority queing threshold based on VLAN class of service for incoming Ethernet packets. VLANCOS is an integer.

Y

N/A

Y

<IPTOS>

(Optional) Priority queing threshold based on IP type of service for incoming Ethernet packets. IPTOS is an integer.

Y

N/A

Y

<NAME>

(Optional) Name. NAME is a string.

Y

N/A

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

Y

N/A

Y

<SUPPRESS>

Pre-service alarm flag for data ports.

Y

N/A

Y

ON

Enable suppress.

Y

N/A

Y

OFF

Disable suppress. Default is Off.

Y

N/A

Y

<SOAK>

(Optional) OOS-AINS to IS transition soak time as measured in 15-minute intervals. SOAK is an integer.

Y

N/A

Y

<LITIMER>

(Optional) Link integrity timer duration in the range between 200 ms and 5000 ms in multiples of 100 ms.

Y

N/A

N

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Y

N/A

Y

Unlocked

In service

Y

N/A

Y

Locked

Out of service

Y

N/A

Y

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Y

N/A

Y

AutomaticInService

Automatic in service

Y

N/A

Y

Disabled

Disabled

Y

N/A

Y

Loopback

Loopback

Y

N/A

Y

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Y

N/A

Y

Maintenance

Maintenance mode

Y

N/A

Y

OutOfGroup

Out of group

Y

N/A

Y

SoftwareDownload

Software downloading

Y

N/A

Y

Unassigned

Unassigned

Y

N/A

Y

NotInstalled

Unequipped

Y

N/A

Y


11.23  ED-EQPT

(Cisco ONS 15454 SDH, Cisco ONS 15600 SDH, and Cisco ONS 15310 MA SDH) The Edit Equipment (ED-EQPT) command edits the attributes for a given equipment slot in the NE. If the card is in an equipment slot, this command is allowed only on the working AID. The ED-EQPT command also modifies a shelf role from NC to SC on an NE configured in multishelf mode.

Usage Guidelines

The PROTID parameter indicates the unique identifier of the protection group (the protect card). "NULL" is a special value of the PROTID parameter and indicates absence of a protection group. For the 1:1 protection type, RVRTV and RVTM parameters can be changed. For the 1:1 protection type, if the PROTID parameter is entered as "NULL", the protection group is deleted, as shown in the following example:

ED-EQPT:[<TID>]:SLOT-2:<CTAG>:::PROTID=NULL;

For the 1:N protection type, if the PROTID is "NULL", the AIDs in the list are removed from the protection group. If all the working cards are in the AID list, the protection group is deleted.

For example, if Slot 1, Slot 2, and Slot 4 were the only working cards in the protection group, the following command will remove Slot 4 from the protection group:

ED-EQPT:[<TID>]:SLOT-4:<CTAG>:::PROTID=NULL;

The protection group still has Slot 1 and Slot 2 as working cards.

The following command will remove all the other working cards in the preceding example and consequently delete the protection group itself:

ED-EQPT:[<TID>]:SLOT-2&SLOT-1:<CTAG>:::PROTID=NULL;

The ED-EQPT command can be successfully executed on an already provisioned card to add or remove a working card from a protection group. This command is not valid on a protect card. Only cards can be added to or removed from a protection group. Protection type is immutable and is determi