Cisco ONS SDH TL1 Command Guide, Release 8.5.1
Chapter 15, INIT Commands
Downloads: This chapterpdf (PDF - 378.0KB) The complete bookPDF (PDF - 13.28MB) | Feedback

INIT Commands

Table Of Contents

INIT Commands

15.1  INIT-REG-<MOD2>

15.2  INIT-SYS


INIT Commands


This chapter provides initialize (INIT) commands for the Cisco ONS 15454 SDH and
Cisco ONS 15600 SDH.

15.1  INIT-REG-<MOD2>

The Initialize Register for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS3I, DV6000, E1, E3, E4, ESCON, ETH, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1,ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, OCH, OMS, OTS, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, or VC12 (INIT-REG-<MOD2>) command initializes the performance monitoring (PM) registers. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The time period is always the current time period, and the previous time period counts are not cleared; therefore, both <MONDAT> and <MONTM> are not supported in this command.

All cards support only the receive (RCV) direction. BTH is not supported for this command.

INIT-REG-<MOD2> can also be used to initialize the remote monitoring (RMON) managed raw data.

Category

Performance

Security

Provisioning

Input Format

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LOCN>],[<DIRN>],[<TMPER>]
[,,];

Input Example

INIT-REG-STM1:CISCO:FAC-1-1:1234::CVL,,NEND,RCV,15-MIN;

Input Parameters

<AID>

Access identifier from the "ALL" section. All of the VC12 and Facility AIDs are supported.

<MONTYPE>

Monitored type. The parameter type is ALL_MONTYPE, which is the monitoring type list.

AISSP

Alarm Indication Signal SecondsPath

ALL

All possible values

BBEP

SDH Background Block Errors Path

BBE-PM

OTN—Background Block Errors—Path Monitor Point

BBER

SDH Background Block Error Ratio

BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as one tenth of a percentage.

BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as one tenth of a percentage.

BBE-SM

OTN—Background Block Errors—Section Monitor Point

BIEC

FEC—Bit Errors Corrected

BIT-EC

The number of bit errors corrected by the FEC algorithm

CGV

8B10B—Code Group Violations

CVCPP

Coding Violations—CP-Bit Path

CVL

Coding Violations—Line

CVP

Coding Violations—Path

CVS

Coding Violations—Section

CVV

Coding Violations—Section

DCG

8B10B—Data Code Groups

ESCPP

Errored Seconds—CPBit Path

ESL

Errored Seconds—Line

ESP

Errored Seconds—Path

ES-PM

OTN—Errored Seconds—Path Monitor Point

ESR

Errored Second—Ratio

ESR-PM

Errored Seconds Ratio—Path monitor Point expressed as tenths of a percentage

ESR-SM

Errored Seconds Ratio—Section monitor Point expressed as tenths of a percentage

ESS

Errored Seconds—Section

ES-SM

OTN—Errored Seconds—Section Monitor Point

ESV

Errored Seconds—VC Path

etherStatsBroadcastPkts

The total number of good packets received that were directed to a multicast address

etherStatsCollisions

Number of transmit packets that are collisions

etherStatsCRCAlignErrors

The total number of packets received that have a length (excluding framing bits, but including frame check sequence [FCS] octets) of between 64 and 1518 octets

etherStatsDropEvents

Number of received frames dropped at the port level

etherStatsFragments

The total number of packets received that were less than 64 octets

etherStatsJabbers

The total number of packets received that are longer than 1518 octets

etherStatsOctets

The total number of octets of data

etherStatsOversizePkts

The total number of packets received that are longer than 1518 octets

etherStatsPkts

The total number of packets (including bad packets, broadcast packets, and multicast packets) received

etherStatsUndersizePkts

The total number of packets received that are less than 64 octets

FCP

Failure Count—Line

FC-PM

OTN—Failure Count—Path Monitor Point

FC-SM

OTN—Failure Count—Section Monitor Point

HP-AR

Availability Ratio

HP-BBE

High-Order Path Background Block Error

HP-BBER

High-Order Path Background Block Error Ratio

HP-EB

High-Order Path Errored Block

HP-ES

High-Order Path Errored Second

HP-ESA

High-Order Path Errored Seconds-A

HP-ESB

High-Order Path Errored Seconds-B

HP-ESR

High-Order Path Errored Second Ratio

HP-FC

High-Order Path Failure Count

HP-NPJC-PDET

High Order Path Negative Pointer Justification Count

HP-NPJC-PGEN

High Order Path Pointer Justification Count Seconds

HP-OI

Outage Intensity

HP-PJCDIFF

High Order Path Pointer Justification Count Difference

HP-PJCS-PDET

High Order Path Pointer Justification Count

HP-PPJC-PDET

High Order Path Positive Pointer Justification Count

HP-PPJC-PGEN

High Order Path, Positive Pointer Justification Count

HP-SEPI

The number of Severely Errored Period Intensity events in available time

HP-SES

High-Order Path Severely Errored Seconds

HP-SESR

High-Order Path Severely Errored Second Ratio

HP-UAS

High-Order Path Unavailable Seconds

ifInBroadcastPkts

Number of broadcast packets received since the last counter reset

ifInDiscards

The number of inbound packets

ifInErrorBytePktss

Receive Error Byte

ifInErrors

The number of inbound packets (or transmission units) that contained errors

ifInFramingErrorPkts

Receive Framing Error

ifInJunkInterPkts

Receive Interpacket Junk

ifInMulticastPkts

Number of multicast packets received since the last counter reset

ifInOctets

Number of bytes transmitted since the last counter reset

ifInUcastPkts

Number of unicast packets received since the last counter reset

ifOutBroadcastPkts

Number of broadcast packets transmitted

ifOutDiscards

The number of outbound packets

ifOutErrors

The number of outbound packets (or transmission units) that could not be transmitted because of errors

ifOutMulticastPkts

Number of multicast packets transmitted

ifOutPayloadCrcErrors

Received payload cyclic redundancy check (CRC) errors

ifOutUcastPkts

Number of unicast packets transmitted

IOS

8B10B-Idle Ordered Sets

IPC

Invalid Packet Count

LBCL-AVG

Average Laser Bias current in micro A

LBCL-MAX

Maximum Laser Bias current in micro A

LBCL-MIN

Minimum Laser Bias current in micro A

LBCN

Normalized Laser Bias Current for STM1-8

LBCN-HWT

Laser Bias current

LBCN-LWT

Laser Bias current

LOSSL

Loss of Signal Seconds—Line

LP-BBE

Low-Order Path Background Block Error

LP-BBER

Low-Order Path Background Block Error Ratio

LP-EB

Low-Order Path Errored Block

LP-ES

Low-Order Path Errored Second

LP-ESA

Low-Order Path Errored Seconds-A

LP-ESB

Low-Order Path Errored Seconds-B

LP-ESR

Low-Order Path Errored Second Ratio

LP-FC

Low-Order Path Failure Count

LP-NPJC-DET

Low Order Negative Pointer Justification Count, Detected

LP-NPJC-GEN

Low Order Negative Pointer Justification Count, Generated

LP-PPJC-DET

Low Order Positive Pointer Justification Count, Detected

LP-PPJC-GEN

Low Order Positive Pointer Justification Count, Generated

LP-SEP

A sequence of between 3 to 9 consecutive severely errored seconds (SES)

LP-SEPI

Low-Order Path Severely Errored Period Intensity

LP-SES

Low-Order Path Severely Errored Seconds

LP-UAS

Low-Order Path Unavailable Seconds

MS-PSC

Multiplex Section-Protection switch count

MS-PSD

Multiplex Section-Protection switch duration

NIOS

8B10B—Non Idle Ordered Sets

NPJC-PDET

Negative Pointer Justification Count, Path Detected

NPJC-PGEN

Negative Pointer Justification Count, Path Generated

OPR-AVG

Average Receive Power in tenths of a micro W

OPR-MAX

Maximum Receive Power in tenths of a micro W

OPR-MIN

Minimum Receive Power in tenths of a micro W

OPRN

Normalized Optical Receive Power for STM1-8

OPRN-MAX

Maximum value for OPRN

OPRN-MIN

Minimum value for OPRN

OPT-AVG

Average Transmit Power in tenths of a micro W

OPT-MAX

Maximum Transmit Power in tenths of a micro W

OPT-MIN

Minimum Transmit Power in tenths of a micro W

OPTN

Normalized value for Optical Power Transmitted for STM1-8 card

OPTN-MAX

Maximum value for OPTN

OPTN-MIN

Minimum value for OPTN

OPWR-AVG

Optical Power—Average Interval Value in tenths of a dBm

OPWR-MAX

Optical Power—Maximum Interval Value in tenths of a dBm

OPWR-MIN

Optical Power—Minimum Interval Value in tenths of a dBm

PPJC-PDET

Positive Pointer Justification Count, Path Detected

PPJC-PGEN

Positive Pointer Justification Count, Path Generated

PSC

Protection Switching Count

PSC-R

Protection Switching Count—Ring

PSC-S

Protection Switching Count—Span

PSC-W

Protection Switching Count—Working

PSD

Protection Switching Duration

PSD-R

Protection Switching Duration—Ring

PSD-S

Protection Switching Duration—Span

PSD-W

Protection Switching Duration—Working

SASCPP

Severely Errored Framing/AIS Second—CP-Bit Path

SASP

Severely Errored Framing/AIS Seconds Path

SEFS

Severely Errored Framing Seconds

SESCPP

Severely Errored Second—CP-Bit Path

SESL

Severely Errored Second—Line

SESP

Severely Errored Second—Path

SES-PM

OTN—Severely Errored Second—Path

SESR

Severely Errored Second—Ratio

SESR-PM

OTN—Severely Errored Second Ratio—Path Monitor Point expressed as tenths of a percentage

SESR-SM

OTN—Severely Errored Second Ratio—Section Monitor Point expressed as tenths of a percentage

SESS

Severely Errored Second—Section

SES-SM

OTN—Severely Errored Second—Section Monitor Point

SESV

Severely Errored Second—VC Path

UASCPP

Unavailable Second—CP-Bit Path

UASL

Unavailable Second—Line

UASP

Unavailable Second—Path

UAS-PM

OTN—Unavailable Second—Path Monitor Point

UAS-SM

OTN—Unavailable Second—Section Monitor Point

UASV

Unavailable Second—VC Path

UNC-WORDS

FEC—Uncorrectable Words

VPC

Valid Packet Count

<LOCN>

(Optional) Location associated with a particular command in reference to the entity identified by the AID. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the Far End of the facility.

NEND

Action occurs on the Near End of the facility.

<DIRN>

(Optional) Direction relative to the entity identified by the AID. Defaults to ALL, which means that the command initializes all of the registers irrespective of the PM direction. The parameter type is DIRECTION (transmit and receive directions).

RCV

Receive direction only

<TMPER>

(Optional) Accumulation time period for performance counters. A null value defaults to 15-MIN. Defaults to 15-MIN. The parameter type is TMPER, which is the accumulation time period for the performance management center.

1-DAY

Performance parameter accumulation interval length; every 24-hours. For SDH PM data only one day of history data is available. For RMON managed PM data seven days of history data are available.

1-HR

Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available.

1-MIN

Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available.

15-MIN

Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length.

RAW-DATA

Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs.


15.2  INIT-SYS

The Initialize System (INIT-SYS) command initializes the specified card and its associated subsystem(s).


Note In Cisco ONS 15600, the SLOT-ALL AID is allowed only for soft reset but not for hard reset.


Usage Guidelines

This command cannot be executed if the network is in a Multiplex-Section Shared Protection Ring (MS-SPRing)

The SLOT-ALL AID and the list AID are not allowed in this command.

Only one level of reset is supported in this command.

It is important that the standby TCC2/TCC2P and CTX cards should be up and running fully standby before this command is sent on the active TCC2/TCC2P and CTX cards for a period of time. During this time, the system is vulnerable to traffic outages caused by timing disruptions or other causes.

The ONS 15310-CL supports the RESET parameters for the 15310-CL-CTX, CE-100T-8, and ML-100T-8 cards only.

The ONS 15600 does not support soft resets on pluggable IO modules (PIMs).

Before a card is hard reset, it must be in one of the following state:ADMIN STATE - LOCKED,MAINTENANCE & SERVICE STATE - LOCKED-ENABLED, MAINTENANCE.

Category

System

Security

Maintenance

Input Format

INIT-SYS:[<TID>]:<AID>:<CTAG>::<PH>[,<CMDMDE=CMDMDE>];

Input Example

INIT-SYS:HOTWATER:SLOT-1:201::1,CMDMDE=FRCD;

Table 15-1 Parameter Support

Parameter
Description
Cisco ONS 15454 SDH
Cisco ONS 15600 SDH
Cisco ONS 15310 MA SDH

<AID>

Access identifier from the "EQPT" section.

Y

Y

Y

<PH>

The phase. 1=soft reset; 2=hard reset. PH is an integer. PH is a required parameter for the ONS 15600, ONS 15310-CL, and ONS 15310-MA.

The PH parameter is supported on the CE-100T-8 and CE-MR-10 cards on the ONS 15454.

Y

Y

Y

<CMDMDE>

(Optional) Command mode. Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in Unlocked-Enabled or Locked-Disabled, AutomaticInService service states.

CMDMDE parameter is not supported on ONS 15310-CL.

N

Y

Y

FRCD

Force the system to override a state in which the command would normally be denied.

Y

Y

Y

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

Y

Y

Y