Cisco ONS SDH TL1 Command Guide, Release 8.5
Chapter 21, RTRV Commands
Downloads: This chapterpdf (PDF - 3.6MB) The complete bookPDF (PDF - 14.48MB) | Feedback

RTRV Commands

Table Of Contents

RTRV Commands

21.1  RTRV-<MOD1FCPAYLOAD>

21.2  RTRV-<MOD1FICONPAYLOAD>

21.3  RTRV-<MOD2DWDMPAYLOAD>

21.4  RTRV-<MOD_RING>

21.5  RTRV-<PATH>

21.6  RTRV-<STM_TYPE>

21.7  RTRV-10GIGE

21.8  RTRV-ALM-<MOD2ALM>

21.9  RTRV-ALMTYPE

21.10  RTRV-ALM-ALL

21.11  RTRV-ALM-BITS

21.12  RTRV-ALM-ENV

21.13  RTRV-ALM-EQPT

21.14  RTRV-ALM-SYNCN

21.15  RTRV-ALMTH-<MOD2>

21.16  RTRV-ALMTH-EQPT

21.17  RTRV-ALS

21.18  RTRV-APC

21.19  RTRV-ATTR-CONT

21.20  RTRV-ATTR-ENV

21.21  RTRV-AUDIT-LOG

21.22  RTRV-BITS

21.23  RTRV-BULKROLL-<STM_TYPE>

21.24  RTRV-CMD-SECU

21.25  RTRV-COND-<MOD2ALM>

21.26  RTRV-COND-ALL

21.27  RTRV-COND-BITS

21.28  RTRV-COND-ENV

21.29  RTRV-COND-EQPT

21.30  RTRV-COND-SYNCN

21.31  RTRV-CONSOLE-PORT

21.32  RTRV-COS-ETH

21.33  RTRV-CRS

21.34  RTRV-CRS-<PATH>

21.35  RTRV-DFLT-SECU

21.36  RTRV-DS3I

21.37  RTRV-E1

21.38  RTRV-E3

21.39  RTRV-E4

21.40  RTRV-EQPT

21.41  RTRV-ESCON

21.42  RTRV-ETH

21.43  RTRV-EXT-CONT

21.44  RTRV-FAC

21.45  RTRV-FFP

21.46  RTRV-FFP-<MOD2DWDMPAYLOAD>

21.47  RTRV-FFP-<STM_TYPE>

21.48  RTRV-FFP-OCH

21.49  RTRV-FSTE

21.50  RTRV-FTPSERVER

21.51  RTRV-G1000

21.52  RTRV-GFP

21.53  RTRV-GIGE

21.54  RTRV-HDLC

21.55  RTRV-HDR

21.56  RTRV-INV

21.57  RTRV-L2-ETH

21.58  RTRV-LMP

21.59  RTRV-LMP-CTRL

21.60  RTRV-LMP-TLINK

21.61  RTRV-LMP-DLINK

21.62  RTRV-LNK

21.63  RTRV-LNKTERM

21.64  RTRV-LOG

21.65  RTRV-MAP-NETWORK

21.66  RTRV-NE-APC

21.67  RTRV-NE-GEN

21.68  RTRV-NE-IPMAP

21.69  RTRV-NE-PATH

21.70  RTRV-NE-SYNCN

21.71  RTRV-NE-WDMANS

21.72  RTRV-NETYPE

21.73  RTRV-NNI-ETH

21.74  RTRV-OCH

21.75  RTRV-OCHCC

21.76  RTRV-OCHNC

21.77  RTRV-OMS

21.78  RTRV-OPM

21.79  RTRV-OTS

21.80  RTRV-PATH-OCH

21.81  RTRV-PM-<MOD2>

21.82  RTRV-PM-ALL

21.83  RTRV-PMMODE-<VC_PATH>

21.84  RTRV-PMSCHED-<MOD2>

21.85  RTRV-PMSCHED-ALL

21.86  RTRV-POS

21.87  RTRV-PROTNSW-<MOD2DWDMPAYLOAD>

21.88  RTRV-PROTNSW-<STM_TYPE>

21.89  RTRV-PROTNSW-<PATH>

21.90  RTRV-PROTNSW-OCH

21.91  RTRV-PROTOCOL

21.92  RTRV-PTHTRC-<PATH>

21.93  RTRV-QNQ-ETH

21.94  RTRV-RMONTH-<MOD2_RMON>

21.95  RTRV-ROLL-<MOD_PATH>

21.96  RTRV-ROUTE

21.97  RTRV-ROUTE-GRE

21.98  RTRV-SLV-WDMANS

21.99  RTRV-STM1E

21.100  RTRV-SYNCN

21.101  RTRV-TACC

21.102  RTRV-TADRMAP

21.103  RTRV-TH-<MOD2>

21.104  RTRV-TH-ALL

21.105  RTRV-TOD

21.106  RTRV-TRAPTABLE

21.107  RTRV-TRC-<STM_MSSPR>

21.108  RTRV-TRC-OCH

21.109  RTRV-TUNNEL-FIREWALL

21.110  RTRV-TUNNEL-PROXY

21.111  RTRV-USER-SECU

21.112  RTRV-VC

21.113  RTRV-VCG

21.114  RTRV-VLAN

21.115  RTRV-WDMANS

21.116  RTRV-WDMSIDE

21.117  RTRV-WLEN


RTRV Commands


This chapter provides retrieve (RTRV) commands for the Cisco ONS 15454 SDH and
Cisco ONS 15600 SDH.

21.1  RTRV-<MOD1FCPAYLOAD>

(Cisco ONS 15454 SDH) The Retrieve 1GFC, 2GFC, 4 GFC, or 10 GFC (RTRV-<MOD1FCPAYLOAD>) command retrieves the attributes related with the Fibre Channel port. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-1GFC:CISCO:FAC-6-1:888;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>,
[LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>],
[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,[<SST>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-1-1:,,WORK,ACT:LINKRATE=1GFC,LINKSTATE=UP,LINKRCVRY=Y,
DISTEXTN=NONE,LINKCREDITS=0,MFS=2148,ENCAP=GFP-T,
NAME=\"FC PORT\",SOAK=32,SOAKLEFT=\"12-25\",FREQ=1550,
LOSSB=LR-1:LOCKED-ENABLED,MAINTENANCE"
;

Output Parameters

<AID>

Access identifier from the "FACILITY" section.

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.

PROT

The entity is a protection unit in the protection group.

WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) The port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

ACT

The entity is the active unit in the shelf.

NA

Status is unavailable.

STBY

The entity is the standby unit in the shelf.

<LINKRATE>

(Optional) The actual rate running on the Fibre Channel port. It can differ from the payload type provisioned. The parameter type is LINKRATE, which is the link rate on a Fibre Channel port.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

UNKNOWN

The rate is unknown.

UNPLUGGED

The Small Form-factor Pluggable (SFP) is not plugged into the Fibre Channel port so the link rate cannot be detected.

<LINKSTATE>

(Optional) Link state. The parameter type is DIRN, which specifies the discriminating level for the requested monitored parameter.

DN

Monitored parameter with values equal to or greater than the level of LEV will be reported.

UP

Monitored parameter with values equal or less than the value of LEV will be reported.

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<DISTEXTN>

(Optional) Distance extension. The parameter type is DISTANCE_EXTENSION (distance extension)

B2B

Buffer to buffer flow control

NONE

No distance extension

LINKCREDITS

(Optional) Number of link credits. LINKCREDITS is an integer.

MFS

(Optional) Maximum frame size. MFS is an integer.

ENCAP

(Optional) Frame encapsulation type. The parameter type is ENCAP, which is the frame encapsulation type.

GFP_F

Generic framing procedure (GFP) frame mode

GFP_T

GFP transparent mode

HDLC

High-level data link control (HDLC) frame mode

HDLC_LEX

HDLC LAN extension frame mode

HDLC_X86

HDLC X.86 frame mode

<NAME>

(Optional) Identifies the port name. NAME is a string.

<SOAK>

(Optional) Locked-Automatic In Service to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.

<SOAKLEFT>

(Optional) Time remaining for the transition from Locked-Automatic In Service to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. The rules for SOAKLEFT are:

When the port is in Locked, Locked_Maintenance or Unlocked state, the parameter will not appear.

When the port is in Locked_AutomaticInService but the countdown has not started due to fault signal, the value will be SOAKLEFT=NOT-STARTED.

When the port is in Locked_AutomaticInService state and the countdown has started, the value will be shown in HH-MM format.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PSTPSTQ>

Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the primary state (PST) and primary state qualifier (PSTQ).

Unlocked-Enabled

In service and normal

Unlocked-Disabled

Out of service and autonomous

Locked-Disabled

Out of service, autonomous and management

Locked-Enabled

Out of service and management

<SST>

(Optional) Secondary state of the entity. The parameter type is secondary state (SST), which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


21.2  RTRV-<MOD1FICONPAYLOAD>

(Cisco ONS 15454 SDH) The Retrieve 1GFICON, 2GFICON, or 4GFICON (RTRV-MOD1FICONPAYLOAD>) command returns Fibre-Channel-specific settings for ports that have been configured to carry fiber connectivity (FICON) traffic using the ENT-FICON command. The MXP_MR_2.5G and MXPP_MR_2.5G cards only support the GFP-T frame type. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-1GFICON:CISCO:FAC-1-1:123;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[LINKRATE=<LINKRATE>],[LINKSTATE=<LINKSTATE>],
[LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>],
[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,<SST>"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-1-1:,,WORK,ACT:LINKRATE=1GFICON,LINKSTATE=UP,LINKRCVRY=Y,
DISTEXTN=NONE,LINKCREDITS=0,MFS=2148,ENCAP=GFP-T,NAME=\"FC PORT\",
SOAK=32,SOAKLEFT=\"12-25\",FREQ=1550,LOSSB=LR-1:LOCKED-ENABLED,
MAINTENANCE"
;

Output Parameters

<AID>

Access identifier from the "FACILITY" section.

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.

PROT

The entity is a protection unit in the protection group.

WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

ACT

The entity is the active unit in the shelf.

NA

Status is unavailable.

STBY

The entity is the standby unit in the shelf.

<LINKRATE>

(Optional) The actual rate running on the Fibre Channel port. It can differ from the payload type provisioned. The parameter type is LINKRATE, which is the link rate on a Fibre Channel port.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

UNKNOWN

The rate is unknown.

UNPLUGGED

The SFP is not plugged into the Fibre Channel port, so the link rate cannot be detected.

<LINKSTATE>

(Optional) Link state. The parameter type is DIRN, which specifies the discriminating level for the requested monitored parameter.

DN

Monitored parameter with values equal to or greater than the level of LEV will be reported.

UP

Monitored parameter with values equal or less than the value of LEV will be reported.

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<DISTEXTN>

(Optional) Distance extension. The parameter type is DISTANCE_EXTENSION (distance extension).

B2B

Buffer-to-buffer flow control

NONE

No distance extension

<LINKCREDITS>

(Optional) Number of link credits. LINKCREDITS is an integer.

<MFS>

(Optional) Maximum frame size. MFS is an integer.

<ENCAP>

(Optional) Frame encapsulation type. The parameter type is ENCAP, which is the frame encapsulation type.

GFP_F

GFP frame mode

GFP_T

GFP transparent mode

HDLC

HDLC frame mode

HDLC_LEX

HDLC LAN extension frame mode

HDLC_X86

HDLC X.86 frame mode

<NAME>

(Optional) Identifies the port name. NAME is a string.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.

<SOAKLEFT>

(Optional) Time remaining for the transition from Locked-AutomaticInService to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. Rules for <SOAKLEFT> are:

When the port is in Locked, Locked_Maintenance or Unlocked state, the parameter will not appear.

When the port is in Locked_AutomaticInService, but the countdown has not started due to fault signal, the value will be SOAKLEFT=NOT-STARTED.

When the port is in Locked_AutomaticInService state and the countdown has started, the value will be shown in HH-MM format.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PSTPSTQ>

Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

Unlocked-Enabled

In service and normal

Unlocked-Disabled

Out of service and autonomous

Locked-Disabled

Out of service, autonomous and management

Locked-Enabled

Out of service and management

<SST>

Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


21.3  RTRV-<MOD2DWDMPAYLOAD>

(Cisco ONS 15454 SDH) The Retrieve D1VIDEO, DV6000, ETRCLO, HDTV, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G and PASSTHRU (RTRV-<MOD2DWDMPAYLOAD>) command retrieves the configuration parameter of a dense wavelength division multiplexing (DWDM) client. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

DWDM

Security

Retrieve

Input Format

RTRV-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-HDTV:MILAN:FAC-1-1:100;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AIDUNIONID>,<AIDTYPE>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],
[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:<PSTPSTQ>,[<SST>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-1-1-1,HDTV:,,WORK,ACT:NAME=\"NY PORT\",LBCL=10.0,OPT=10.0,OPR=10.0,
FREQ=1550,LOSSB=LR-1:UNLOCKED-DISABLED,AUTOMATICINSERVICE"
;

Output Parameters

<AIDUNIONID>

Access identifier from the "AidUnionId" section.

<AIDTYPE>

A type of access identifier. The parameter type is MOD2DWDMPAYLOAD, which is the payload types applicable to DWDM ports.

10GFC

10-Gigabit Fibre Channel payload

10GIGE

10-Gigabit Ethernet

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

D1VIDEO

D1Video payload

DV6000

DV6000 payload

ETRCLO

ETRCLO payload

GIGE

Gigabit Ethernet payload

HDTV

HDTV payload

ISC1

ISC1 payload

ISC3

ISC3 payload

PASSTHRU

Any pass-through (2R) payload

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit has in the protection group.

PROT

The entity is a protection unit in the protection group.

WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

ACT

The entity is the active unit in the shelf.

NA

Status is unavailable.

STBY

The entity is the standby unit in the shelf.

<NAME>

(Optional) Identifies the port name. NAME is a string.

<LBCL>

(Optional) Displays the current value of the laser current. LBCL is a float.

<OPT>

(Optional) Displays the current value of the transmitted optical power. OPT is a float.

<OPR>

(Optional) Displays the current value of the received optical power. OPR is a float.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PSTPSTQ>

Primary state of the entity. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

Unlocked-Enabled

In service and normal

Unlocked-Disabled

Out of service and autonomous

Locked-Disabled

Out of service, autonomous and management

Locked-Enabled

Out of service and management

<SST>

(Optional) Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


21.4  RTRV-<MOD_RING>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Multiplex Section Shared Protection Ring (RTRV-<MOD_RING>) command retrieves the multiplex section-shared protection ring (MS-SPRing) information of the network element (NE). A two-fiber or four-fiber MS-SPRing can be retrieved.

Usage Guidelines

Error conditions:

Only ALL, NULL, MSSPR-ALL, or MSSPR-RINGID is allowed for this command.

A NULL AID defaults to the AID ALL.

The list AID format is supported.

If the system fails on getting information object repository (IOR), a Get IOR Failed (SROF) error message is returned.

If the AID is invalid, an Invalid AID (IIAC) error message is returned.

If the MS-SPRing does not exist, a MSSPR Does Not Exist (SRQN) error message is returned.

Category

MS-SPRing

Security

Retrieve

Input Format

RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::];

Input Example

RTRV-MSSPR:PETALUMA:ALL:123;

Input Parameters

<AID>

(Optional) Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE. Only ALL, null or a list of MSSPR-# in AID are allowed. A null value is equivalent to ALL.


Output Format

SID DATE TIME
M CTAG COMPLD
"[<AID>]::[RINGID=<RINGID>],[NODEID=<NODEID>],[MODE=<MODE>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>],
[EASTWORK=<EASTWORK>],[WESTWORK=<WESTWORK>],[EASTPROT=<EASTPROT>],
[WESTPROT=<WESTPROT>]"
;

Output Example

4F MS-SPRing

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"MSSPR-43::RINGID=43,NODEID=3,MODE=4F,RVRTV=Y,RVTM=5.0,
SRVRTV=Y,SRVTM=5.0,EASTWORK=FAC-5-1,WESTWORK=FAC-6-1,
EASTPROT=FAC-12-1,WESTPROT=FAC-13-1"
;

2F MS-SPRing

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"MSSPR-N12EF::RINGID=N12EF,NODEID=2,MODE=2F,RVRTV=Y,RVTM=5.0,
EASTWORK=FAC-5-1,WESTWORK=FAC-6-1"
;

Output Parameters

<AID>

(Optional) Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE.

<RINGID>

(Optional) The MS-SPRing ID of the NE up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.

<NODEID>

(Optional) The MS-SPRing node ID of the NE. NODEID ranges from 0 to 31. NODEID is a string.

<MODE>

(Optional) Mode with which the command is to be implemented. Identifies the MS-SPRing mode; either two-fiber or four-fiber. The parameter type is MSSPR_MODE, which is the MS-SPRing mode.

2F

Two-fiber MS-SPRing

4F

Four-fiber MS-SPRing

<RVRTV>

(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Does not revert service to original line after restoration.

Y

Reverts service to original line after restoration.

<RVTM>

(Optional) Revertive time. RVTM is not allowed to be set while RVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<SRVRTV>

(Optional) The span revertive mode for four-fiber MS-SPRing only. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<SRVTM>

(Optional) The span revertive time for four-fiber MS-SPRing only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<EASTWORK>

(Optional) East working facility. AID from the "FACILITY" section.

<WESTWORK>

(Optional) West working facility. AID from the "FACILITY" section.

<EASTPROT>

(Optional) East protecting facility. AID from the "FACILITY" section.

<WESTPROT>

(Optional) West protecting facility. AID from the "FACILITY" section.


21.5  RTRV-<PATH>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve VC3, VC44C, VC38C, VC464C, VC48C, VC4-12C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (RTRV-<PATH>) command retrieves the attributes associated with an VC path. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

Supported AIDs are: ALL, SLOT-N (N=1,2,...,ALL), and VC-specific AIDs.

The SFBER, SDBER, RVRTV, RVTM, SWPDIP, HOLDOFFTIMER, and SNCPPTHSTATE parameters only apply to subnetwork connection protection (SNCP).

The path trace message is a 64 character string including the terminating carriage return (CR) and line feed (LF) that is transported in the J1 byte of the SDH VC path overhead.

The EXPTRC indicates the contents of the expected incoming path trace that are provisioned by the user in the ED-VC_PATH command. The TRC indicates the contents of the outgoing path trace message. The INCTRC indicates the contents of the incoming path trace message.

The path trace mode has three modes: OFF, MANUAL, and AUTO. The mode defaults to OFF. The MANUAL mode compares the received string with the user-entered expected string. The AUTO mode compares the present received string with an expected string set to a previously received string. If there is a mismatch, the TIM-P alarm is raised. When the path trace mode is in OFF mode, there is no path trace processing, and all the alarm and state conditions are reset.

When the expected string is queried under the OFF path trace mode, the expected string is a copy of the provisioned string, or NULL. When an expected string is queried under the MANUAL path trace mode, the expected string is a copy of the user entered string. When an expected string is queried under the AUTO path trace mode, the expected string is either a copy of the acquired received string, or NULL if the string has not been acquired.

When the incoming string is queried under the OFF path trace mode, the incoming string is NULL. When an incoming string is queried under the MANUAL or AUTO path trace mode, the incoming string is either a copy of the received string, or NULL if the string has not been received.

J1 (EXPTRC) is implemented on the STM1, STM16AS, STM64, MRC-12, and STM64-XFP cards.

The optional parameter MSSPRPTHTYPE provides more options to retrieve J1/C2 of a particular MS-SPRing path. This field is valid only if the queried AID port has MS-SPRing. The MSSPRPTHTYPE defaults to NON-PCA path type if the MS-SPRing is switched, or defaults to PCA if there is no MS-SPRing switching.

Sending this command while MSSPRPTHTYPE=PCA, whether there is MS-SPRing switch or not, the protection channel access (PCA) path J1/C2 data will be returned (if there is PCA circuit on the AID). Sending this command with a VC AID without circuits and no MS-SPRing switched on the VC, will return and error message.

An optional output parameter MSSPRPTHSTATE is introduced into this command output. Each J1/C2 output data of this command will include the MS-SPRing path state information.

After the MS-SPRing switching, the J1/IPPM/C2 data can be retrieved over the protection path. Provisioning J1 trace string, trace mode, or threshold is not allowed on the protection path.

HOLDOFFTIMER is not specific to a path. Instead, it is applicable to the SNCP selector.

To retrieve either the cross-connect points or the test access points (TAPs) on the DS3i-N-12 card, the RTRV-VC3 command with the appropriate AID must be used.

For the selector path on an MS-SPRing, the SWPDIP path attribute is not editable and is always in the ON state.

Category

Paths

Security

Retrieve

Input Format

RTRV-<PATH>:[<TID>]:<AID>:<CTAG>:::[MSSPRPTHTYPE=<MSSPRPTHTYPE>][:];

Input Example

RTRV-VC4:FERNDALE:VC4-2-1-4:238:::MSSPRPTHTYPE=NON-PCA;

Input Parameters

<AID>

Access identifier from the "CrossConnectId1" section.

<MSSPRPTHTYPE>

(Optional) The MS-SPRing path type (only if the port is on the MS-SPRing). Defaults to NON-PCA. Applicable only to VC-level paths in SDH. A null value defaults to NON-PCA. The parameter type is MSSPR_PTH_TYPE, which is the MS-SPRing path type only if the port is on the MS-SPRing.

NON-PCA

The AID is on the working path, or the cross-connection card protection path.

PCA

The AID is on the MS-SPRing PCA path.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>],[SFBER=<SFBER>],[SDBER=<SDBER>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[SWPDIP=<SWPDIP>],[HOLDOFFTIMER=<HOLDOFFTIMER>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>],[INCTRC=<INCTRC>],
[TRCMODE=<TRCMODE>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[SNCPPTHSTATE=<SNCPPTHSTATE>],[C2=<C2>],
[MSSPRPTHSTATE=<MSSPRPTHSTATE>]:<PSTPSTQ>,[<SSTQ>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"VC4-2-1-4::LEVEL=VC3,SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,SWPDIP=Y,
HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
INCTRC="INCTRCSTRING",TRCMODE=AUTO,TACC=8,TAPTYPE=DUAL,
SNCPPTHSTATE=ACT,C2=0X04,
MSSPRPTHSTATE=PROTPTHACT:UNLOCKED-DISABLED,AUTOMATICINSERVICE"
;

Output Parameters

<AID>

Access identifier from the "CrossConnectId1" section.

<LEVEL>

(Optional) The rate of the cross-connected channel. Applicable only to High-Order paths (VC4). The parameter type is PATH, which is the modifier for path commands.

VC3

Synchronous Transport Signal/Module Level-1 (51 Mbps)

VC44C

Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps)

VC38C

Synchronous Transport Signal/Module Level-18 Concatenated (933 Mbps)

VC464C

Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps)

VC48C

Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps)

VC4

Synchronous Transport Signal/Module Signal Level-3 Concatenated (155 Mbps)

VC416C

Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps)

VC42C

Synchronous Transport Signal/Module level-6 (310 Mbps)

VC43C

Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps)

VC12

Virtual Tributary 2. Virtual Channel 12

<SFBER>

(Optional) A VC path signal failure threshold that only applies to SNCP. Applicable only to High-Order paths. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) A VC path signal degrade threshold that only applies to SNCP. Applicable only High-Order paths. Defaults 1E-6. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<RVRTV>

(Optional) Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Does not revert service to original line after restoration.

Y

Reverts service to original line after restoration.

RVTM

(Optional) Revertive time. Only applies to SNCP. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

SWPDIP

(Optional) Switch on PDI-P. Applicable only to VC-level paths (VCn). The parameter type is ON_OFF (disable or enable an attribute)

N

Disable an attribute.

Y

Enable an attribute.

<HOLDOFFTIMER>

(Optional) Hold off timer. HOLDOFFTIMER is an integer.

<EXPTRC>

(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR and LF. Applicable to VC-level paths (VCn). Defaults to NULL when SNCP path is created. EXPTRC is a string.

<TRC>

(Optional) The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. A null value defaults to the NE transmitting null characters (Hex 00). Applicable to VC-level paths (VCn). TRC is a string.

<INCTRC>

(Optional) The incoming path trace message contents. INCTRC is any combination of 64 characters. Applicable only to VC-level paths in (VCn). Defaults to Null when a SNCP path is created. INCTRC is a string.

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level paths (VCn). Defaults to OFF when a SNCP path is created. The parameter type is TRCMODE, which is the trace mode.

AUTO

Use the previously received path trace string as the expected string (not applicable to MXP_2.5G_10G and TXP_MR_10G cards).

AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP detected.

MAN

Use the provisioned expected string as the expected string.

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP detected.

OFF

Turn off path trace capability. Nothing will be reported.

<TACC>

(Optional) Test access. Indicates whether the digroup being provisioned is to be used as a test access digroup. Defaults to N.

<TAPTYPE>

(Optional) TAP type. The parameter type is TAPTYPE, which is the test access point type.

DUAL

Dual facility access digroup (FAD).

SINGLE

Single FAD

<SNCPPTHSTATE>

(Optional) Indicates whether a given AID is the working or standby path of a SNCP cross-connect. The parameter type is STATUS, which is the status of the unit in the protection pair.

ACT

The entity is the active unit in the shelf.

NA

Status is unavailable.

STBY

The entity is the standby unit in the shelf.

<C2>

(Optional) The C2 byte hex code. Applicable only to VC-level paths (VCn). The parameter type is C2_BYTE, which is the C2 byte hex code.

0X00

Unequipped

0X01

Equipped-Non Specific payload

0X02

VT-Structured VC-1 synchronous payload envelope (SPE)

0X03

Locked Virtual Tributary (VT) mode

0X04

Asynchronous Mapping for DS3

0X12

Asynchronous Mapping for DS4 North American (NA)

0X13

Mapping for asynchronous transfer mode (ATM)

0X14

Mapping for distributed queue dual bus (DQDB)

0X15

Asynchronous Mapping for fiber distributed data interface (FDDI)

0X16

High-level data link control (HDLC)-Over-SDH Mapping

0XE1

VT-structured VC4-1 SPE with 1VTx payload defect

0XE2

VT-structured VC4-1 SPE with 2VTx payload defects

0XE3

VT-structured VC4-1 SPE with 3VTx payload defects

0XE4

VT-structured VC4-1 SPE with 4VTx payload defects

0XE5

VT-structured VC4-1 SPE with 5VTx payload defects

0XE6

VT-structured VC4-1 SPE with 6VTx payload defects

0XE7

VT-structured VC4-1 SPE with 7VTx payload defects

0XE8

VT-structured VC4-1 SPE with 8VTx payload defects

0XE9

VT-structured VC4-1 SPE with 9VTx payload defects

0XEA

VT-structured VC4-1 SPE with 10VTx payload defects

0XEB

VT-structured VC4-1 SPE with 11VTx payload defects

0XEC

VT-structured VC4-1 SPE with 12VTx payload defects

0XED

VT-structured VC4-1 SPE with 13VTx payload defects

0XEE

VT-structured VC4-1 SPE with 14VTx payload defects

0XEF

VT-structured VC4-1 SPE with 15VTx payload defects

0XF0

VT-structured VC4-1 SPE with 16VTx payload defects

0XF1

VT-structured VC4-1 SPE with 17VTx payload defects

0XF2

VT-structured VC4-1 SPE with 18VTx payload defects

0XF3

VT-structured VC4-1 SPE with 19VTx payload defects

0XF4

VT-structured VC4-1 SPE with 20VTx payload defects

0XF5

VT-structured VC4-1 SPE with 21VTx payload defects

0XF6

VT-structured VC4-1 SPE with 22VTx payload defects

0XF7

VT-structured VC4-1 SPE with 23VTx payload defects

0XF8

VT-structured VC4-1 SPE with 24VTx payload defects

0XF9

VT-structured VC4-1 SPE with 25VTx payload defects

0XFA

VT-structured VC4-1 SPE with 26VTx payload defects

0XFB

VT-structured VC4-1 SPE with 27VTx payload defects

0XFC

VT-structured VC4-1 SPE with 28VTx payload defects

0XFE

O.181 Test Signal (TSS1 to TSS3) Mapping

0XFF

Reserved. C2 is 0XFF if AIS-L is being generated by an optical card or cross-connect downstream.

<MSSPRPTHSTATE>

(Optional) The MS-SPRing path state only if the port is on the MS-SPRing. Applicable only to VC-level paths in SDH (VCn). The parameter type is MSSPR_PTH_STATE, which is the MS-SPRing path state only if the port is on the MS-SPRing.

PCAPTHACT

Indicates that the MS-SPRing switched and its PCA path is in the active state.

PCAPTHSTB

Indicates that the MS-SPRing switched and its PCA path is in the standby state.

PROTPTHACT

Indicates that the MS-SPRing switched and its protection path is in the active state.

WKGPTHACT

Indicates that the MS-SPRing switched and its working path is in the active state.

WKGPTHSTB

Indicates that the MS-SPRing switched and its working path is in the standby state.

<PSTPSTQ>

Administrative state in the PST_PSTQ format. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and the PSTQ.

Unlocked-Enabled

In service and normal

Unlocked-Disabled

Out of service and autonomous

Locked-Disabled

Out of service, autonomous and management

Locked-Enabled

Out of service and management

<SSTQ>

(Optional) Secondary state of the entity. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


21.6  RTRV-<STM_TYPE>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve (STM1, STM4, STM16, STM64) command retrieves the attributes (such as service parameters) and the state of an STM facility. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

Both RINGID and MSSPRTYPE identify the STM port connected with a MS-SPRing. These attributes are only presented for the STM4, STM16, and STM64 ports within a MS-SPRing connection. The RTRV-<MOD_RING> command with the AID MSSPR-RINGID, can provide more information on this MS-SPRing.

This command does not show the WVLEN attribute if the STM port has zero value on WVLEN.

Category

Ports

Security

Retrieve

Input Format

RTRV-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-STM16:PENNGROVE:FAC-6-1:236;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[RSDCC=<RSDCC>],[AREA=<AREA>],
[TMGREF=<TMGREF>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],
[PJMON=<PJMON>],[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],
[WVLEN=<WVLEN>],[RINGID=<RINGID>],[MSSPRTYPE=<MSSPRTYPE>],
[MUX=<MUX>],[UNIC=<UNIC>],[CCID=<CCID>],[NBRIX=<NBRIX>],[SOAK=<SOAK>],
[SOAKLEFT=<SOAKLEFT>],[SSMRCV=<SSMRCV>],[OSPF=<OSPF>],
[MSDCC=<MSDCC>],[NAME=<NAME>],[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],
[EXPTRC=<EXPTRC>],[TRC=<TRC>], [TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>], [SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>], [FOREIGNIPADDRESS=<FOREIGNIPADDRESS>],
<PSTPSTQ>,[<SSTQ>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-6-1:,,WORK,ACT:RSDCC=Y,AREA=10.92.63.1,TMGREF=N,SYNCMSG=N,SENDDUS=N,
PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,WVLEN=1310.00,RINGID=43,
MSSPRTYPE=WESTWORK,MUX=E2,UNIC=Y,CCID=8,NBRIX=2,SOAK=52,
SOAKLEFT=12-25,SSMRCV=STU_SDH,OSPF=Y,MSDCC=Y,NAME=\"STM PORT\",
LBCL=10.0,OPT=10.0,OPR=10.0, EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCFORMAT=16-BYTE,ADMSSM=G811, SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=Y,
FOREIGNIPADDRESS=10.92.63.44,UNLOCKED-DISABLED,AUTOMATICINSERVICE"
;

Output Parameters

<AID>

Access identifier from the "FACILITY" section.

<ROLE>

(Optional) An STM port role. The parameter type is SIDE, which is the role the unit is playing in the protection group.

PROT

The entity is a protection unit in the protection group.

WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) An STM port status. The parameter type is STATUS, which is the status of the unit in the protection pair.

ACT

The entity is the active unit in the shelf.

NA

Status is unavailable.

STBY

The entity is the standby unit in the shelf.

<RSDCC>

(Optional) Indicates whether or not the regenerator section DCC (RS-DCC) is to be used. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<AREA>

(Optional) Area ID. Shows up only if the DCC is enabled. AREA is a string.

<TMGREF>

(Optional) The termination to be used, whether primary or secondary. Identifies if an STM port has a timing reference. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute)

N

Disable an attribute.

Y

Enable an attribute.

<SYNCMSG>

(Optional) Synchronization status message. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<SENDDUS>

(Optional) The facility will send the Do Not Use for Synchronization (DUS) value in 0x0f bit pattern as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute)

N

Disable an attribute.

Y

Enable an attribute.

<PJMON>

(Optional) Identifies an STM port PJMON. Defaults to 0 (zero). PJMON is an integer. Set a valid VC4 number of the optical port.

Note The PJMON number displayed in TL1 interface does not correspond to the PJVC4MON number in CTC, but instead corresponds to the VC4 number of the optical port.

<SFBER>

(Optional) An STM port signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) An STM port signal degrade threshold. Defaults 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<MODE>

(Optional) STM port mode. Defaults to SDH. The parameter type is OPTICAL_MODE, which is the facility's optical mode.

SINGLESHELF

The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.

MULTISHELF

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.

MULTISHELFETH

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.

<WVLEN>

(Optional) An STM port wavelength, expressed in nanometers. For example, WVLEN=1310.00 means it operates at 1310 nm in the DWDM application. WVLEN is a float.

<RINGID>

(Optional) The MS-SPRing RINGID with which the port is connected. RINGID ranges from 0 to 9999. RINGID is an integer.

<MSSPRTYPE>

(Optional) The MS-SPRing type with which the port is connected. The parameter type is MSSPR_TYPE, which is the MS-SPRing type of an STM port.

EASTPROT

The STM port is an east protecting port.

EASTWORK

The STM port is an east working port.

WESTPROT

The STM port is an west protecting port.

WESTWORK

The STM port is an west working port.

<MUX>

(Optional) MS-SPRing extension byte. The parameter type is MUX_TYPE, which is the MS-SPRing extension byte.

E2

E2 byte (orderwire)

F1

F1 byte (user)

K3

K3 byte

Z2

Z2 byte

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. SOAK is an integer.

<SOAKLEFT>

(Optional) Time remaining for the transition from Locked-AutomaticInService to Unlocked measured in 1 minute intervals. The format is HH-MM where HH ranges from 00 to 48 and MM ranges from 00 to 59. Rules for <SOAKLEFT> are:

When the port is in Locked, Locked_Maintenance or Unlocked state, the parameter will not appear.

When the port is in Locked_AutomaticInService, but the countdown has not started due to fault signal the value will be SOAKLEFT=NOT-STARTED.

When the port is in Locked_AutomaticInService state and the countdown has started the value will be shown in HH-MM format.

<SSMRCV>

(Optional) Displays the quality of the individual port. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

DUS_SDH

Do Not Use For Synchronization

G811

G811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

G812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

G812TL Standard

SETS

Synchronous Equipment Timing Source

<OSPF>

(Optional) The Open Shortest Path First discovery. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<MS-DCC>

(Optional) The line DCC connection on the port. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<NAME>

(Optional) Port Name. NAME is a string.

<LBCL>

(Optional) Displays the current value of the laser current. LBCL is a float.

<OPT>

(Optional) Displays the current value of the transmitted optical power. OPT is only displayed for DWDM cards. OPT is a float.

<OPR>

(Optional) Received optical power. OPR is a float.

<EXPTRC>

(Optional) Expected path trace content. EXPTRC is a string.

<TRC>

(Optional) Path trace message to be transmitted. TRC is a string.

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level Paths in SDH (VCn). Defaults to the OFF mode. The parameter type is TRCMODE (trace mode).

AUTO

Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.

AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected.

MAN

Use the provisioned expected string as the expected string.

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected.

OFF

Turn off path trace capability. Nothing will be reported.

<TRCFORMAT>

(Optional) Trace message size. The parameter type is TRCFORMAT, which is the trace format.

1-BYTE

1 byte trace message

16-BYTE

16 byte trace message

64-BYTE

64 byte trace message

Y

Enable an attribute

<ADMSSM>

(Optional) SSM selectable value. Only displayed when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

DUS_SDH

Do Not Use For Synchronization

G811

G811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

G812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

G812TL Standard

SETS

Synchronous Equipment Timing Source

<SENDDUSFF>

(Optional) Indicates that the facility will send the DUS value in 0xff bits pattern as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute

Y

Enable an attribute

<AISONLPBK>

(Optional) The parameter type is AIS_ON_LPBK, which indicates if AIS should be sent on loopback.

AIS_ONLPBK_FACILITY

AIS is sent on facility loopback.

AIS_ON_LPBK_ALL

AIS is sent on all loopbacks.

AIS_ON_LPBK_OFF

AIS is not sent on loopback.

AIS_ON_LPBK_TERMINAL

AIS is sent on terminal loopback.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<FOREIGNFEND>

(Optional) Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF (disable or enabled an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<FOREIGNIP>

(Optional) The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGNIP is a string.

<PSTPSTQ>

(Optional) Administrative state in the PST_PSTQ format. The parameter type is PST_PSTQ, which is the service state of the entity described by the PST and PSTQ.

Unlocked-Enabled

In service and normal

Unlocked -Disabled

Out of service and autonomous

Locked-Disabled

Out of service, autonomous and management

Locked-Enabled

Out of service and management

<SSTQ>

(Optional) The secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


21.7  RTRV-10GIGE

(Cisco ONS 15454 SDH) The Retrieve 10GIGE (RTRV-10GIGE) command retrieves the 10-Gbps-specific parameters for a port that has been configured to support the Gigabit Ethernet payload with the ENT-10GIGE command.

Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-10GIGE:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-10GIGE:TID:FAC-1-1:100;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],[MACADDR=<MACADDR>],
[LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:
<PSTPSTQ>,[<SST>]"
;

Output Examples

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-6-1:,,WORK,ACT:NAME=\"NY PORT\",MACADDR=00-0E-AA-BB-CC-FF,LBCL=10.0,
OPT=10.0,OPR=10.0,FREQ=1550,LOSSB=SX:Unlocked-Disabled,AutomaticInService"
;

Output Parameters

<AID>

Access identifier from the "FACILITY" section.

<ROLE>

(Optional) The port role in a Y-cable protection scheme. The parameter type is SIDE, which is the role the unit is playing in the protection group.

PROT

The entity is a protection unit in the protection group.

WORK

The entity is a working unit in the protection group.

<STATUS>

(Optional) Port status in a Y-cable protection scheme. The parameter type is STATUS, which is the status of the unit in the protection pair.

ACT

The entity is the active unit in the shelf.

NA

Status is unavailable.

STBY

The entity is the standby unit in the shelf.

<NAME>

(Optional) Port name. NAME is a string.

<MACADDR>

(Optional) The MAC address for the 10 Gigabit Ethernet payload. MACADDR is a string.

<LBCL>

(Optional) Displays the current value of the laser current. LBCL is a float.

<OPT>

(Optional) Displays the current value of the transmitted optical power. OPT is a float.

<OPR>

(Optional) Displays the current value of the received optical power. OPR is a float.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PSTPSTQ>

Administrative state in the PSTPSTQ format. The parameter type is PSTPSTQ, which is the service state of the entity described by the PST and the PSTQ.

Unlocked-Enabled

In service and normal

Unlocked -Disabled

Out of service and autonomous

Locked-Disabled

Out of service, autonomous and management

Locked-Enabled

Out of service and management

<SST>

(Optional) Secondary state of the entity. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


21.8  RTRV-ALM-<MOD2ALM>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, DS1, DS3I, E1, E100, E1000, E3, E4, EC1, ETH, FSTE, G1000, GFPOS, GIGE, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, OCH, OMS, OTS, OTU2, POS, RPRIF, STM1, STM4, STM16, STM64, STM1E, VC3, VC4-4C, VC4-6C, VC4-64C, VC4-8C, VC4-12C, VC4, VC4-16C, VC4-2C, VC4-3C, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-16c, VC4-64c, VC11, VC12, VC3, VCG, VC11, VC12, or WLEN (RTRV-ALRM-<MOD2ALM>) command retrieves and sends the current status of alarm conditions. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

VT1-n-n-n replaces PS_VC12-n-n-n for the VC12 alarm AID.

The [<AIDTYPE>] shows VC3 for VC alarms.

Category

Fault

Security

Retrieve

Input Format

RTRV-ALM-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>],[<LOCN>],[<DIRN>][,];

Input Example

RTRV-ALM-OC12:ELDRIDGE:FAC-5-1:225::MN,SD,SA,NEND,RCV;

Input Parameters

<AID>

Access identifier from the "AidUnionId" section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

(Optional) Condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, Not Alarmed (NA) conditions, and Not Reported (NR) conditions. See the Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-5-1,OC12:MJ,SD,SA,09-05,12-30-20,NEND,RCV:\"BER AT SIGNAL DEGRADE LEVEL\","
;

Output Parameters

<AID>

Access identifier from the "ALL" section.

<AIDTYPE>

(Optional) Type of access identifier. The parameter type is MOD2ALM, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

1GISC3

1-Gigabit ISC3 compatible

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

CLNT

Client facility for MXP/TXP cards

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GFPOS

Generic framing protocol over packet over SDH virtual port alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

ML1000-2

(ONS 15454) ML-Series two port Gigabit Ethernet card

OCH

Optical channel

OCHTERM

OCH termination

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC38C

VC38C alarm

VC44C

VC44C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

UDCDCC

UDCDCC alarm

UDCF

UCDF alarm

VCG

Virtual concatenation group alarm

WLEN

Wavelength path provisioning

<NTFCNCDE>

Two-letter notification code. the parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See the Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) The condition description.


21.9  RTRV-ALMTYPE

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm Type command retrieves all system and user-defined alarm types.

Usage Guidelines

None

Category

System

Security

Retrieve

Input Format

RTRV-ALMTYPE:[<TID>]::<CTAG>;

Input Example

RTRV-ALMTYPE:CISCONODE::1;

Input Parameters

None.

Output Format

SID DATE TIME
M CTAG COMPLD
"<TYPEOFALM>,<ALMTYPE>"
;

Output Examples

CISCONODE 2007-06-26 14:30:00
M 1 COMPLD
"SYSTEMDEFINED,AIRCOMPR"
;

Output Parameters

<ALMTYPE>

Specifies user-defined alarm types associated with virtual wires in environmental alarm inputs.

<TYPEOFALM>

Specifies the type of alarm, i.e. system or user-defined.

SYSTEMDEFINED

Specifies a system-defined alarm type.

USERDEFINED

Specifies a user-defined alarm type.


21.10  RTRV-ALM-ALL

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm All (RTRV-ALM-ALL) command retrieves and sends the current status of all active alarm conditions. The alarm condition or severity to be retrieved is specified using the input parameters as a filter. To retrieve all the NE alarms, issue all of the following commands:

RTRV-ALM-ALL
RTRV-ALM-BITS
RTRV-ALM-ENV
RTRV-ALM-SYNCN

Usage Guidelines

None

Category

Fault

Security

Retrieve

Input Format

RTRV-ALM-ALL:[<TID>]:[<AID>]:<CTAG>::[<NTFCNCDE>],
[<CONDITION>],[<SRVEFF>],[<LOCN>],[<DIRN>],[,];

Input Example

RTRV-ALM-ALL:COTATI:ALL:229::MN,PWRRESTART,NSA,NEND,RCV;

Input Parameters

<AID>

Access identifier from the "ALL" section. A null value is equivalent to ALL. AID is a string.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

<CONDITION>

(Optional) The type of alarm condition. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<LOCN>],[<DIRN>]:
[<DESC>],[<AIDDET>]"

;

Output Examples

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SLOT-2,EQPT:MN,PWRRESTART,NSA,08-01,14-25-59,NEND,RCV:\"POWER FAIL RESTART\", DS1-14"
;

Output Parameters

<AID>

(Optional) Access identifier from the "ALL" section.

<AIDTYPE>

(Optional) Type of facility, link, or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

BITS

Building integrated timing supply (BITS) alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

ML1000-2

(ONS 15454) ML-Series two port Gigabit Ethernet card

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<OCRDAT>

Date when the specific event or violation occurred, MM-DD.

<OCRTM>

Time when the specific event or violation occurred, HH-MM-SS.

<DESC>

(Optional) A condition description. DESC is a string.

<AIDDET>

(Optional) The supplementary equipment identification. AIDDET uses the same addressing rules as the AID, but specifies AID type and additional details about the entity being managed.


21.11  RTRV-ALM-BITS

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm Building Integrated Timing Supply (RTRV-ALM-BITS) command retrieves and sends the current status of alarm conditions associated with the BITS facility. The alarm condition or severity retrieved is specified using the input parameters as a filter.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],
[<LOCN>],[<DIRN>];

Input Example

RTRV-ALM-BITS:ELVERANO:BITS-1:228::CR,LOS,SA;

Input Parameters

<AID>

Access identifier from the "BITS" section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is a two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed

NR

The alarm is not reported

<CONDTYPE>

(Optional) The condition type for an alarm or reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>],:[<DESC>]"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"BITS-1,BITS:CR,LOS,SA,08-01,14-25-59,,:\"LOSS OF SIGNAL\","
;

Output Parameters

<AID>

Access identifier from the "BITS" section.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

BITS

BITS alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) A condition description. DESC is a string.


21.12  RTRV-ALM-ENV

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm Environment (RTRV-ALM-ENV) command retrieves the environmental alarms.

Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];

Input Example

RTRV-ALM-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;

Input Parameters

<AID>

Access identifier from the "ENV" section.

Note For RTRV-ALM-ENV, only ENV-IN-{1-4} is a valid AID. ENV-OUT-{1,6} is not a valid AID for RTRV-ALM-ENV.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

AIRCOMPR

Air compressor failure

AIRCOND

Air conditioning failure

AIRDRYR

Air dryer failure

BATDSCHRG

Battery discharging

BATTERY

Battery failure

CLFAN

Cooling fan failure

CPMAJOR

Centralized power major failure

CPMINOR

Centralized power minor failure

ENGINE

Engine failure

ENGOPRG

Engine operating

ENGTRANS

Standby engine transfer

EXPLGS

Explosive gas

FIRDETR

Fire detector failure

FIRE

Fire

FLOOD

Flood

FUELLEAK

Fuel leak

FUSE

Fuse failure

GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

HATCH

Controlled Environment Vault (CEV) hatch fail

GEN

Generator failure

HIAIR

High air flow

HIHUM

High humidity

HITEMP

High temperature

HIWTR

High water

INTRUDER

Intrusion

LEVELCON

Level converter

LVDADSL

Secondary asymmetric digital subscriber line (ADSL) low voltage disconnect

LVDBYPAS

Low voltage disconnected bypass

LWBATVG

Low battery voltage

LWFUEL

Low fuel

LWHUM

Low humidity

LWPRES

Low cable pressure

LWTEMP

Low temperature

LWWTR

Low water

MISC

Miscellaneous

OPENDR

Open door

POWER

Commercial power failure

PUMP

Pump failure

PWR-48

48 V power supply failure

PWR-139

-139 V power converter

PWR-190

-190 V power converter

PWRMJ

Power supply major

PWRMN

Power supply minor

RECT

Rectifier failure

RECTHI

Rectifier high voltage

RECTLO

Rectifier low voltage

RINGGENMJ

Ringing generator major

RINGGENMN

Ringing generator minor

RTACADSL

AC or AC/rectifier power fail ADSL equipment

RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

RTACPWR

AC or AC/rectifier power fail DCL equipment

RTACPWRENG

Commercial AC fail, site equipped with standby engine

RTBAYPWR

AC power loss distributed power RT bay

RTRVENG

Retrieve standby engine, commercial AC restored

SMOKE

Smoke

TEMP

High-low temperature

TOXICGAS

Toxic gas

TREPEATER

T-repeater shelf

VENTN

Ventilation system failure


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ENV-IN-1:MJ,OPENDR,08-01,14-25-59,\"OPEN DOOR\""
;

Output Parameters

<AID>

Access identifier from the "ENV" section.

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<ALMTYPE>

The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

AIRCOMPR

Air compressor failure

AIRCOND

Air conditioning failure

AIRDRYR

Air dryer failure

BATDSCHRG

Battery discharging

BATTERY

Battery failure

CLFAN

Cooling fan failure

CPMAJOR

Centralized power major failure

CPMINOR

Centralized power minor failure

ENGINE

Engine failure

ENGOPRG

Engine operating

ENGTRANS

Standby engine transfer

EXPLGS

Explosive gas

FIRDETR

Fire detector failure

FIRE

Fire

FLOOD

Flood

FUELLEAK

Fuel leak

FUSE

Fuse failure

GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

HATCH

CEV hatch fail

GEN

Generator failure

HIAIR

High air flow

HIHUM

High humidity

HITEMP

High temperature

HIWTR

High water

INTRUDER

Intrusion

LEVELCON

Level converter

LVDADSL

Secondary ADSL low voltage disconnect

LVDBYPAS

Low voltage disconnect bypass

LWBATVG

Low battery voltage

LWFUEL

Low fuel

LWHUM

Low humidity

LWPRES

Low cable pressure

LWTEMP

Low temperature

LWWTR

Low water

MISC

Miscellaneous

OPENDR

Open door

POWER

Commercial power failure

PUMP

Pump failure

PWR-48

48 V power supply failure

PWR-139

-139 V power converter

PWR-190

-190 V power converter

PWRMJ

Power supply major

PWRMN

Power supply minor

RECT

Rectifier failure

RECTHI

Rectifier high voltage

RECTLO

Rectifier low voltage

RINGGENMJ

Ringing generator major

RINGGENMN

Ringing generator minor

RTACADSL

AC or AC/rectifier power fail ADSL equipment

RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

RTACPWR

AC or AC/rectifier power fail DCL equipment

RTACPWRENG

Commercial AC fail, site equipped with standby engine

RTBAYPWR

AC power loss distributed power RT bay

RTRVENG

Retrieve standby engine, commercial AC restored

SMOKE

Smoke

TEMP

High-low temperature

TOXICGAS

Toxic gas

TREPEATER

T-repeater shelf

VENTN

Ventilation system failure

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<DESC>

(Optional) A condition description. DESC is a string.


21.13  RTRV-ALM-EQPT

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm Equipment (RTRV-ALM-EQPT) command retrieves and sends the current status of alarm conditions associated with the equipment units. The alarm condition or severity to be retrieved is specified using the input parameters as a filter.

Usage Guidelines

None

Category

Equipment

Security

Retrieve

Input Format

RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>],
[<LOCN>],[<DIRN>];

Input Example

RTRV-ALM-EQPT:TWOROCK:SLOT-7:227::MJ,HITEMP,NSA;

Input Parameters

<AID>

Access identifier from the "EQPT" section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

(Optional) The condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SLOT-7,EQPT:MJ,HITEMP,NSA,08-01,14-25-59,,:\"HI TEMPERATURE\","
;

Output Parameters

<AID>

(Optional) Access identifier from the "EQPT" section.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

BITS

BITS alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) A condition description. DESC is a string.


21.14  RTRV-ALM-SYNCN

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Alarm Synchronization (RTRV-ALM-SYNCN) command retrieves and sends the current status of alarm conditions associated with a synchronization facility. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>],[<LOCN>],[<DIRN>];

Input Example

RTRV-ALM-SYNCN:FULTON:SYNC-NE:226::CR,FAILTOSW,SA;

Input Parameters

<AID>

Access identifier from the "SYNC_REF" section.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

(Optional) The condition type for an alarm or a reported event. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service. A null value is equivalent to ALL.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,
[<OCRDAT>],[<OCRTM>],[<LOCN>],[<DIRN>]:[<DESC>]"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SYNC-NE,SYNCN:CR,FAILTOSW,SA,
08-01,14-25-59,,:\"FAILURE TO SWITCH TO PROTECTION\","
;

Output Parameters

<AID>

Access identifier from the "SYN" section.

<AIDTYPE>

(Optional) Type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gbps fiber connection

BITS

BITS alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<NTFCNCDE>

Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) A condition description. DESC is a string.


21.15  RTRV-ALMTH-<MOD2>

(Cisco ONS 15454 SDH and Cisco ONS 15600 SDH) The Retrieve Alarm Threshold for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, D1VIDEO, DS1, DS3I, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM1, STM4, STM16, STM64, GIGE, POS, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c, or VC4-64c (RTRV-ALMTH-<MOD2>) command retrieves the alarm threshold values.

Usage Guidelines

None

Category

DWDM

Security

Retrieve

Input Format

RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<ALMTHR>[,,::];

Input Example

RTRV-ALMTH-STM64::FAC-1-1:C::OPT-HIGH;

Input Parameters

<AID>

Access identifier from the "ALL" section.

<ALMTHR>

Alarm threshold. Must not be null. The parameter type is ALM_THR, which is the alarm threshold list for MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, MD-4-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

BATV-EHIGH

Battery Voltage—Extremely High

BATV-ELOW

Battery Voltage—Extremely Low

BATV-HIGH

Battery Voltage—High

BATV-LOW

Battery Voltage—Low

GAIN-HDEG

Gain not reached—High Degrade Threshold

GAIN-HFAIL

Gain not reached—High Failure Threshold

GAIN-LDEG

Gain not reached—Low Degrade Threshold

GAIN-LFAIL

Gain not reached—Low Failure Threshold

LBCL-HIGH

Laser Bias Current in microA as a tenth of a percentage of the High Warning Threshold, Low Warning Threshold. Measured value 0.0%, 100.0%.

OPR-HIGH

Receive power in 1tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPR-LOW

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-HIGH

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-LOW

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPWR-HDEG

Optical Power—High Degrade Threshold

OPWR-HFAIL

Optical Power—High Failure Threshold

OPWR-LDEG

Optical Power—Low Degrade Threshold

OPWR-LFAIL

Optical Power—Low Failure Threshold

VOA-HDEG

VOA Attenuation—High Degrade Threshold

VOA-HFAIL

VOA Attenuation—High Failure Threshold

VOA-LDEG

VOA Attenuation—Low Degrade Threshold

VOA-LFAIL

VOA Attenuation—Low Failure Threshold


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"CHAN-2-2,OCH:OPT-HIGH,,,20"
;

Output Parameters

<AID>

Access identifier from the "ALL" section.

<MOD>

AID type. The parameter type is MOD2, which is the line/path modifier.

10GFC

10-Gigabit Fibre Channel payload

10GIGE

10-Gigabit Ethernet

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

D1VIDEO

D1 Video

DS3I

DS3i-N-12 Line

DV6000

DV6000

E1

E1

E3

E3

E4

E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode

ESCON

ESCON

ETRCLO

ETRCLO

FSTE

FSTE facility

G1000

G1000 facility

GFPOS

Generic Framing Protocol over Packet Over SDH. Virtual ports partitioned using GFP's multiplexing capability.

GIGE

Gigabit Ethernet

HDTV

HDTV

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

STM1

STM1 facility

STM4

STM4 facility

STM16

STM16 facility

STM64

STM64 facility

OCH

Optical channel

OCHCC

OCH client connection

OCHNC

OCH network connection

OCHTERM

OCH termination

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port

STM1E

STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.

VC3

VC3 path

VC44C

VC44C path

VC38C

VC38C path

VC464C

VC464C path

VC48C

VC48C path

VC4

VC4 path

VC416C

VC416C path

VC42C

VC42C path

VC43C

VC43C path

VC11

VC11 path

VC12

VC12 path

<CONDTYPE>

Condition type for an alarm or a reported event. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

BATV-EHIGH

Battery Voltage—Extremely High

BATV-ELOW

Battery Voltage—Extremely Low

BATV-HIGH

Battery Voltage—High

BATV-LOW

Battery Voltage—Low

GAIN-HDEG

Gain not reached—High Degrade Threshold

GAIN-HFAIL

Gain not reached—High Failure Threshold

GAIN-LDEG

Gain not reached—Low Degrade Threshold

GAIN-LFAIL

Gain not reached—Low Failure Threshold

LBCL-HIGH

Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold Measured value [0.0%, 100.0%]

OPR-HIGH

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPR-LOW

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-HIGH

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-LOW

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPWR-HDEG

Optical Power—High Degrade Threshold

OPWR-HFAIL

Optical Power—High Failure Threshold

OPWR-LDEG

Optical Power—Low Degrade Threshold

OPWR-LFAIL

Optical Power—Low Failure Threshold

VOA-HDEG

VOA Attenuation—High Degrade Threshold

VOA-HFAIL

VOA Attenuation—High Failure Threshold

VOA-LDEG

VOA Attenuation—Low Degrade Threshold

VOA-LFAIL

VOA Attenuation—Low Failure Threshold

<THLEVEL>

Threshold level. THLEVEL is a float.


21.16  RTRV-ALMTH-EQPT

(Cisco ONS 15454 SDH and Cisco ONS 15600 SDH) The Retrieve Alarm Threshold Equipment (RTRV-ALMTH-EQPT) command retrieves the alarm thresholds for the power level monitoring on an NE.

Usage Guidelines

None

Category

Equipment

Security

Retrieve

Input Format

RTRV-ALMTH-EQPT:[<TID>]:[<AID]>:<CTAG>::[<CONDTYPE>][,,::];

Input Examples

RTRV-ALMTH-EQPT:::1::BATV-HIGH;

RTRV-ALMTH-EQPT::SHELF-2:1::BATV-HIGH;

Input Parameters

<AID>

(Optional) The node or shelf access identifier from the "SHELF" section. If omitted, it addresses the node or first shelf of the node.

<CONDTYPE>

Alarm threshold. A null value is equivalent to ALL. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

BATV-EHIGH

Battery Voltage—Extremely High

BATV-ELOW

Battery Voltage—Extremely Low

BATV-HIGH

Battery Voltage—High

BATV-LOW

Battery Voltage—Low

GAIN-HDEG

Gain not reached—High Degrade Threshold

GAIN-HFAIL

Gain not reached—High Failure Threshold

GAIN-LDEG

Gain not reached—Low Degrade Threshold

GAIN-LFAIL

Gain not reached—Low Failure Threshold

LBCL-HIGH

Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold. Measured value [0.0%, 100.0%]

OPR-HIGH

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPR-LOW

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-HIGH

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-LOW

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPWR-HDEG

Optical Power—High Degrade Threshold

OPWR-HFAIL

Optical Power—High Failure Threshold

OPWR-LDEG

Optical Power—Low Degrade Threshold

OPWR-LFAIL

Optical Power—Low Failure Threshold

VOA-HDEG

VOA Attenuation—High Degrade Threshold

VOA-HFAIL

VOA Attenuation—High Failure Threshold

VOA-LDEG

VOA Attenuation—Low Degrade Threshold

VOA-LFAIL

VOA Attenuation—Low Failure Threshold


Output Format

SID DATE TIME
M CTAG COMPLD
"[<AID>],<MOD2B>:<CONDTYPE>,,,<DNFIELD>"

;

Output Examples

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"SHELF-1,EQPT:BATV-HIGH,,,-52.0,"
;

TID-000 1998-06-20 14:30:00
M 001 COMPLD
",EQPT:BATV-HIGH,,,-52.0,""
;

Output Parameters

<AID>

(Optional) The node or shelf access identifier from the "SHELF" section. If omitted, it addresses the node or first shelf of the node.

<MOD2B>

Alarm type. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

BITS

BITS alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet Port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<CONDTYPE>

Alarm threshold. The parameter type is ALM_THR, which is the alarm threshold list for the MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, 4MD-xx.x, 32MUX, 32DMX, AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

BATV-EHIGH

Battery Voltage—Extremely High

BATV-ELOW

Battery Voltage—Extremely Low

BATV-HIGH

Battery Voltage—High

BATV-LOW

Battery Voltage—Low

GAIN-HDEG

Gain not reached—High Degrade Threshold

GAIN-HFAIL

Gain not reached—High Failure Threshold

GAIN-LDEG

Gain not reached—Low Degrade Threshold

GAIN-LFAIL

Gain not reached—Low Failure Threshold

LBCL-HIGH

Laser Bias Current in microA as tenths of a percentage of High Warning Threshold, Low Warning Threshold. Measured value [0.0%, 100.0%].

OPR-HIGH

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPR-LOW

Receive power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-HIGH

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPT-LOW

Transmit power in tenths of a microW. Measured value -40.0 dBm, +30.0 dBm.

OPWR-HDEG

Optical Power—High Degrade Threshold

OPWR-HFAIL

Optical Power—High Failure Threshold

OPWR-LDEG

Optical Power—Low Degrade Threshold

OPWR-LFAIL

Optical Power—Low Failure Threshold

VOA-HDEG

VOA Attenuation—High Degrade Threshold

VOA-HFAIL

VOA Attenuation—High Failure Threshold

VOA-LDEG

VOA Attenuation—Low Degrade Threshold

VOA-LFAIL

VOA Attenuation—Low Failure Threshold

<DNFIELD>

DNFIELD is a float.


21.17  RTRV-ALS

(Cisco ONS 15454 SDH and Cisco ONS 15600 SDH) The Retrieve Automatic Laser Shutoff (RTRV-ALS) command retrieves the ALS attributes of an STM facility and all the facilities that support the ALS feature. This command is used to retrieve the ALS parameter of the STM16 and STM64 ports on the MXP_2.5G_10E, TXP_MR_10E, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_2.5G_10G, and TXP_MR_10G cards.

Usage Guidelines

None

Category

Ports

Security

Retrieve

Input Format

RTRV-ALS:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-ALS:PENNGROVE:FAC-1-1:1;

Input Parameters

<AID>

Access identifier from the "AidUnionId" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>],[LSRSTAT=<LSRSTAT>]"

;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-6-1,STM64::ALSMODE=DISABLED,ALSRCINT=100,ALSRCPW=2.0,LSRSTAT=UP:"
;

Output Parameters

<AID>

Access identifier from the "AidUnionId" section.

<AIDTYPE>

Type of access identifier. The parameter type is MOD2, which is the line/path modifier.

10GFC

10-Gigabit Fibre Channel payload

10GFICON

10-Gigabit fiber connectivity payload

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

1GISC3

1-Gigabit ISC3 compatible

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

2GISC3

2-Gigabit ISC3 compatible

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

D1VIDEO

D1 video

DS3I

DS3i-N-12 line

DV6000

DV6000

E1

E1

E3

E3

E4

E4 frame. Only applicable to STM1E Ports 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode.

ESCON

ESCON

ETRCLO

ETRCLO

FSTE

FSTE facility

G1000

G1000 facility

GFPOS

Generic Framing Protocol over Packet Over SDH. Virtual ports partitioned using GFP's multiplexing capability.

GIGE

Gigabit Ethernet

HDTV

HDTV

ISC3PEER1G

1-Gigabit ISC3 Peer

ISC3PEER2G

2-Gigabit ISC3 Peer

ISC3PEER2R

1-Gigabit or 2-Gigabit ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gigabit ISC1, ISC2, and ISC3 compatibility

OCH

Optical Channel

OCHCC

OCH client connection

OCHNC

OCH network connection

OCHTERM

OCH termination

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port

STM1

STM1 facility

STM1E

STM1E facility. Only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card

STM4

STM4 facility

STM16

STM16 facility

STM64

STM64 facility

VC3

VC3 path

VC44C

VC4-4C path

VC38C

VC3-8C path

VC464C

VC4-64C path

VC48C

VC4-8C path

VC4

VC4 path

VC416C

VC4-16C path

VC42C

VC4-2C path

VC43C

VC4-3C path

VC11

VC11 path

VC12

VC12 path

<ALSMODE>

(Optional) ALS is enabled or disabled. The parameter type is ALS_MODE, which is the working mode for automatic laser shutdown.

AUTO

Automatic

DISABLED

Disabled

MAN

Manual

MAN-RESTART

Manual restart for test

<ALSRCINT>

(Optional) ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer.

<ALSRCPW>

(Optional) ALS recovery pulse width. The range is 2.0 to 100.00 seconds, in increments of 100 ms. ALSRCPW is a float.

<LSRSTAT>

(Optional) Status of the laser. The parameter type is LASER_STATUS, which is the status of laser.

APR

Laser is switched on but is working automatic power reduction.

OFF

Laser is switched off.

ON

Laser is switched on.


21.18  RTRV-APC

(Cisco ONS 15454 SDH) The Operate Amplifier Power Control (RTRV-APC) command retrieves the APC application attributes.

Usage Guidelines

None

Category

DWDM

Security

Maintenance

Input Format

RTRV-APC:[<TID>]::<CTAG>;

Input Example

RTRV-APC:PENNGROVE:WDMSIDE-A:114;

Input Parameters

None

Output Format

SID DATE TIME
M CTAG COMPLD
"::[APCENABLE=<APCENABLE>],[APCSTATE=<APCSTATE>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"::APCENABLE=Y,APCSTATE=WORKING"
;

Output Parameters

<WDMSIDE>

The AID is used to access the WDM side of an MSTP node.

WDMSIDE-{UNKNOWN,A,B,C,D,E,F,G,H}

MSTP side identifier

<APCENABLE>

(Optional) Enable or disable of the APC application. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<APCSTATE>

(Optional) Indicates the status of the APC application. The parameter type is APC_STATE, which is the APC status.

DISABLE

The APC is disabled by the user and is not working.

FORCED-DISABLE

The APC has been internally disabled by the node and is not working.

WORKING

The APC is enabled by the user and is working.


21.19  RTRV-ATTR-CONT

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Attribute Control (RTRV-ATTR-CONT) command retrieves and sends the attributes associated with an external control. These attributes are used when an external control is operated or released. To set these attributes, use the SET-ATTR-CONT command.

Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];

Input Example

RTRV-ATTR-CONT:CISCO:ENV-OUT-2:123::AIRCOND;

Input Parameters

<AID>

Access identifier from the "ENV" section. Identifies the external control for which attributes are being set.

<CONTTYPE>

(Optional) Environmental control type. A null value is equivalent to ALL. The parameter type is CONTTYPE, which is the environmental control type.

AIRCOND

Air conditioning

ENGINE

Engine

FAN

Fan

GEN

Generator

HEAT

Heat

LIGHT

Light

MISC

Miscellaneous

SPKLR

Sprinkler


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:[<CONTTYPE>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ENV-OUT-2:AIRCOND"
;

Output Parameters

<AID>

Access identifier from the "ENV" section. Identifies the external control for which attributes are being set.

<CONTTYPE>

(Optional) Environmental control type. A null value is equivalent to ALL. The parameter type is CONTTYPE, which is the environmental control type.

AIRCOND

Air conditioning

ENGINE

Engine

FAN

Fan

GEN

Generator

HEAT

Heat

LIGHT

Light

MISC

Miscellaneous

SPKLR

Sprinkler


21.20  RTRV-ATTR-ENV

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Attribute Environment (RTRV-ATTR-ENV) command retrieves the attributes associated with an environmental alarm.

Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];

Input Example

RTRV-ATTR-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;

Input Parameters

<AID>

Access identifier from the "ENV" section.

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

AIRCOMPR

Air compressor failure

AIRCOND

Air conditioning failure

AIRDRYR

Air dryer failure

BATDSCHRG

Battery discharging

BATTERY

Battery failure

CLFAN

Cooling fan failure

CPMAJOR

Centralized power major failure

CPMINOR

Centralized power minor failure

ENGINE

Engine failure

ENGOPRG

Engine operating

ENGTRANS

Standby engine transfer

EXPLGS

Explosive gas

FIRDETR

Fire detector failure

FIRE

Fire

FLOOD

Flood

FUELLEAK

Fuel leak

FUSE

Fuse failure

GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

HATCH

CEV hatch fail

GEN

Generator failure

HIAIR

High air flow

HIHUM

High humidity

HITEMP

High temperature

HIWTR

High water

INTRUDER

Intrusion

LEVELCON

Level converter

LVDADSL

Secondary ADSL low voltage disconnect

LVDBYPAS

Low voltage disconnect bypass

LWBATVG

Low battery voltage

LWFUEL

Low fuel

LWHUM

Low humidity

LWPRES

Low cable pressure

LWTEMP

Low temperature

LWWTR

Low water

MISC

Miscellaneous

OPENDR

Open door

POWER

Commercial power failure

PUMP

Pump failure

PWR-48

48 V power supply failure

PWR-139

-139 V power converter

PWR-190

-190 V power converter

PWRMJ

Power supply major

PWRMN

Power supply minor

RECT

Rectifier failure

RECTHI

Rectifier high voltage

RECTLO

Rectifier low voltage

RINGGENMJ

Ringing generator major

RINGGENMN

Ringing generator minor

RTACADSL

AC or AC/rectifier power fail ADSL equipment

RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

RTACPWR

AC or AC/rectifier power fail DCL equipment

RTACPWRENG

Commercial AC fail, site equipped with standby engine

RTBAYPWR

AC power loss distributed power RT bay

RTRVENG

Retrieve standby engine, commercial AC restored

SMOKE

Smoke

TEMP

High-low temperature

TOXICGAS

Toxic gas

TREPEATER

T-repeater shelf

VENTN

Ventilation system failure


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"ENV-IN-1:MJ,OPENDR,\"OPEN DOOR\""
;

Output Parameters

<AID>

Access identifier from the "ENV" section.

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. The parameter type is ENV_ALM, which is the environmental alarm type.

AIRCOMPR

Air compressor failure

AIRCOND

Air conditioning failure

AIRDRYR

Air dryer failure

BATDSCHRG

Battery discharging

BATTERY

Battery failure

CLFAN

Cooling fan failure

CPMAJOR

Centralized power major failure

CPMINOR

Centralized power minor failure

ENGINE

Engine failure

ENGOPRG

Engine operating

ENGTRANS

Standby engine transfer

EXPLGS

Explosive gas

FIRDETR

Fire detector failure

FIRE

Fire

FLOOD

Flood

FUELLEAK

Fuel leak

FUSE

Fuse failure

GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

HATCH

CEV hatch fail

GEN

Generator failure

HIAIR

High air flow

HIHUM

High humidity

HITEMP

High temperature

HIWTR

High water

INTRUDER

Intrusion

LEVELCON

Level converter

LVDADSL

Secondary ADSL low voltage disconnect

LVDBYPAS

Low voltage disconnect bypass

LWBATVG

Low battery voltage

LWFUEL

Low fuel

LWHUM

Low humidity

LWPRES

Low cable pressure

LWTEMP

Low temperature

LWWTR

Low water

MISC

Miscellaneous

OPENDR

Open door

POWER

Commercial power failure

PUMP

Pump failure

PWR-48

48 V power supply failure

PWR-139

-139 V power converter

PWR-190

-190 V power converter

PWRMJ

Power supply major

PWRMN

Power supply minor

RECT

Rectifier failure

RECTHI

Rectifier high voltage

RECTLO

Rectifier low voltage

RINGGENMJ

Ringing generator major

RINGGENMN

Ringing generator minor

RTACADSL

AC or AC/rectifier power fail ADSL equipment

RTACCRIT

AC or AC/rectifier power fail DCL equipment critical site

RTACPWR

AC or AC/rectifier power fail DCL equipment

RTACPWRENG

Commercial AC fail, site equipped with standby engine

RTBAYPWR

AC power loss distributed power RT bay

RTRVENG

Retrieve standby engine, commercial AC restored

SMOKE

Smoke

TEMP

High-low temperature

TOXICGAS

Toxic gas

TREPEATER

T-repeater shelf

VENTN

Ventilation system failure

<DESC>

(Optional) Alarm description. DESC is a string.


21.21  RTRV-AUDIT-LOG

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Audit Log (RTRV-AUDIT-LOG) command retrieves the contents of the audit log stored in the NE. Audit records contain information for user operations such as login, logout, change of provisioning parameters and other changes a user might make when connected to the NE. Audit records do not store operations related to parameter retrieval.

Usage Guidelines

None

Category

Log

Security

Superuser

Input Format

RTRV-AUDIT-LOG:[<TID>]::<CTAG>;

Input Example

RTRV-AUDIT-LOG:::1;

Input Parameters

None

Output Format

SID DATE TIME
M CTAG COMPLD
" <ENTRYNUM>,<OCRDAT>,<OCRTM>,<TASKID>,<TXSTATUS>,<DESCRIPTION>"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"17172,2004-10-05,09-52-44, TPROVMGR,COMPLD,\"DESCRIPTION\""
;

Output Parameters

<ENTRYNUM>

Entry number. ENTRYNUM is an integer.

<OCRDAT>

Date when the specific event or violation occurred, MM-DD.

<OCRTM>

Time when the specific event or violation occurred, HH-MM-SS.

<TASKID>

Task ID. TASKID is a string.

<TXSTATUS>

The parameter type is TX_STATUS, which indicates the status of the transferred file.

COMPLD

The file transmission is completed.

IP

The file transmission is in process.

START

The file transmission is started.

<DESCRIPTION>

Description of event. The description format varies depending on the event and can include parameters used during the event. DESCRIPTION is a string.


21.22  RTRV-BITS

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Building Integrated Timing Supply (RTRV-BITS) command retrieves the BITS configuration command.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::];

Input Example

RTRV-BITS:SONOMA:BITS-1:782;

Input Parameters

<AID>

Access identifier from the "BITS" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[IMPEDANCE=<IMPEDANCE>],[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>]:[<PST>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"BITS-1::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,AISTHRSHLD=G811,
SABIT=BYTE-4,IMPEDANCE=120-OHM,BITSFAC=E1,ADMSSM=G811:UNLOCKED"
;

Output Parameters

<AID>

Access identifier from the "BITS" section.

<LINECDE>

(Optional) Line code. The parameter type is LINE_CODE (line code).

AMI

Line code value is AMI.

B8ZS

Line code value is B8ZS (bipolar with eight-zero substitution).

HDB3

Line Code HDB3. Only applicable to SDH E1 signal.

<FMT>

(Optional) Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.

D4

Frame format is D4.

E1-CRCMF

SDH E1 CRCMF frame format

E1-MF

SDH E1 MF frame format

E1-UNFRAMED

SDH E1 unframed format

ESF

Frame format is ESF.

UNFRAMED

Frame format is unframed.

<LBO>

(Optional) BIS line build out settings. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line buildout).

0-133

BITS line buildout range is 0 to 133.

134-266

BITS line buildout range is 134 to 266.

267-399

BITS line buildout range is 267 to 399.

400-533

BITS line buildout range is 400 to 533.

534-655

BITS line buildout range is 534 to 655.

<SYNCMSG>

(Optional) Indicates if the BITS facility supports synchronization status message. Default is on (Y). The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<AISTHRSHLD>

(Optional) Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

DUS_SDH

Do Not Use For Synchronization

G811

ITU-T G.811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

ITU-T G.812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

ITU-T G.812TL Standard

SETS

Synchronous Equipment Timing Source

<SABIT>

(Optional) When the frame format selection is E1, SABIT is the BIT used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).

BYTE-4

SABIT is BYTE-4.

BYTE-5

SABIT is BYTE-5.

BYTE-6

SABIT is BYTE-6.

BYTE-7

SABIT is BYTE-7.

BYTE-8

SABIT is BYTE-8.

<IMPEDANCE>

(Optional) When the frame format selection is E1, IMPEDANCE is the terminal impedance of the BITS-IN port. The parameter type is IMPEDANCE, which is the terminal impedance of the BITS-IN port.

120-OHM

Impedance of 120 ohm

75-OHM

Impedance of 75 ohm

<BITSFAC>

(Optional) BITS facility settings. The parameter type is BITS_FAC, which is the BITS facility rate. 64 k and 6 MHz are only applicable to SDH.

2 M

2 MHz rate

64 K

64 K rate

6 M

6 MHz rate

E1

E1 rate

<ADMSSM>

(Optional) SSM selectable. Only applicable to BITS-IN when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

DUS_SDH

Do Not Use For Synchronization

G811

ITU-T G.811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

ITU-T G.812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

ITU-T G.812TL Standard

SETS

Synchronous Equipment Timing Source

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service


21.23  RTRV-BULKROLL-<STM_TYPE>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Bulkroll for STM4, STM64, STM1, or STM16 (RTRV-BULKROLL-STM_TYPE>) command retrieves roll data parameters on a line. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Bridge and Roll

Security

Retrieve

Input Format

RTRV-BULKROLL-<STM_TYPE>:[<TID>]:<SRC>:<CTAG>;

Input Example

RTRV-BULKROLL-STM4:CISCO:FAC-3-1:1;

Input Parameters

<SRC>

Source AID from the "FACILITY" section.


Output Format

SID DATE TIME
M CTAG COMPLD
"<FROM>:RFROM=<RFROM>,RTO=<RTO>,[RMODE=<RMODE>],VLDSIG=<VLDSIG>"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"VC4-3-1-1:RFROM=VC4-3-1-1,RTO=VC4-5-1-1,RMODE=AUTO,VLDSIG=Y"
;

Output Parameters

<FROM>

One of the endpoints. Access identifier from the "FACILITY" section for line level rolling and bulk rolling.

<RFROM>

The termination point of the existing cross-connect that is to be rolled. AID is from the "VC" section.

<RTO>

The the termination point that will become a leg of the new cross-connection. AID is from the "VC" section.

<RMODE>

(Optional) The rolling mode of operation. The parameter type is RMODE, which specifies the roll mode.

AUTO

Automatic. When a valid signal is available, the roll under AUTO mode will automatically delete the previous endpoint.

MAN

Manual. Enter the corresponding delete roll/bulkroll command to delete the previous endpoint.

<VLDSIG>

(Optional) The rolling mode of operation. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.


21.24  RTRV-CMD-SECU

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Command Security (RTRV-CMD-SECU) command retrieves the current command security level of the command specified in the AID field.

Usage Guidelines

None

Category

Security

Security

Superuser

Input Format

RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>;

Input Example

RTRV-CMD-SECU::INIT-REG:1;

Input Parameters

<AID>

Access identifier string. Identifies the entity in the NE to which the command pertains. It is the command verb along with verb modifier(s), as it currently exists. It can be a single command or a block of commands, where the block might include all commands. Only INIT-REG will be supported. AID is a string.


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>:<CAP>"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"INIT-REG:PROV"
;

Output Parameters

<AID>

Access identifier. It can be a single command or a block of commands, where the block can include all commands. Only INIT-REG is supported. AID is a string.

<CAP>

Command access privilege. The parameter type is PRIVILEGE, which is the security level.

PROV

Provision security level

SUPER

Superuser security level


21.25  RTRV-COND-<MOD2ALM>

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Condition for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, DS1, DS3I, E1, E100, E1000, E3, E4, EC1, FSTE, G1000, ETH, GFPOS, GIGE, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, STM4, STM64, STM1, STM16, OCH, OMS, OTS, OTU2, POS, RPRIF, STM1, STM4, STM16, STM64, STM1E, VC3, VC4-4C, VC4-6C, VC4-64C, VC4-8C, VC4-12C, VC4, VC4-16C, VC4-2C, VC4-3C, T1, T3, UDCDCC, UDCF, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-8c, VC4-16c,VC4-64c, VC11, VC12, VCG, VC11, VC12, or WLEN (RTRV-COND-<MOD2ALM>) command retrieves the current standing condition and state associated with an entity.

Usage Guidelines

None

Category

Fault

Security

Retrieve

Input Format

RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

RTRV-COND-RPRIF:DXT:RPRIF-2-0:229::FORCE-REQ;

Input Parameters

<AID>

Access identifier from the "ALL" section.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>],[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"RPRIF-2-0,E1:MJ,FORCE-REQ,SA,01-01,16-00-20,NEND,RCV,\"FORCED SWITCH REQUEST\""
;

Output Parameters

<AID>

Access identifier from the "ALL" section

<AIDTYPE>

(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2ALM—alarm type

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

1GISC3

1-Gigabit ISC3 compatible

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

CLNT

Client facility for MXP/TXP cards

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 frame. Only applicable to STM1E port 9 through 12 when it is in E4-FRAMED or E4-UNFRAMED mode

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GFPOS

Generic framing protocol over packet over SDH virtual port alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gbps ISC3 Peer

ISC3PEER2G

2-Gbps ISC3 Peer

ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OCHTERM

OCH termination

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E facility, only applicable to the STM1E facility (when it is in STM1E mode) of SDH STM1E-12 card.

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC38C

VC38C alarm

VC44C

VC44C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

UDCDCC

UDCDCC alarm

UDCF

UCDF alarm

VCG

Virtual concatenation group alarm

WLEN

Wavelength path provisioning

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<TYPEREP>

The condition itself. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRECTION>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.


21.26  RTRV-COND-ALL

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Condition All (RTRV-COND-ALL) command retrieves the current standing condition for all entities.

Usage Guidelines

This command does not return all conditions that are returned by other, more specific RTRV-COND commands; RTRV-COND-ALL returns a subset of these conditions. Telcordia GR-253-CORE, Section 6.2.1.8.4 states that a retrieval that returns ALL conditions from a node (RTRV-COND-ALL) must omit any conditions that have the same root cause as other raised conditions. The section also states that any retrieval of a subset of the conditions from a node, regardless of how the subsetting occurs, should not omit these same-root-cause conditions. So, for example, RTRV-COND-VC3 includes the same-root-cause conditions in the set it returns and, RTRV-COND-ALL does not.

To retrieve all of the NE conditions, issue all of the following commands:

RTRV-COND-ALL
RTRV-COND-ENV
RTRV-COND-BITS
RTRV-COND-SYNCN

Category

Fault

Security

Retrieve

Input Format

RTRV-COND-ALL:[<TID>]:[<AID>]:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

RTRV-COND-ALL:DXT:ALL:229::LOS;

Input Parameters

<AID>

(Optional) Access identifier from the "ALL" section. AID is a string. A null value is equivalent to ALL.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>],[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"RPRIF-2-0,T3:MJ,FORCE-REQ,SA,01-01,16-00-20,NEND,RCV,\"FORCED SWITCH REQUEST\""
;

Output Parameters

<AID>

Access identifier from the "ALL" section for the entity that has an alarm condition.

<AIDTYPE>

(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

BITS

BITS alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gbps ISC3 Peer

ISC3PEER2G

2-Gbps ISC3 Peer

ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed

NR

The alarm is not reported

<TYPEREP>

The type of condition to be retrieved. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, which is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRECTION>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.


21.27  RTRV-COND-BITS

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Condition Building Integrated Timing Supply (RTRV-COND-BITS) command retrieves the standing conditions on BITS.

Usage Guidelines

None

Category

Synchronization

Security

Retrieve

Input Format

RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>],[<LOCN>],[<DIRN>];

Input Example

RTRV-COND-BITS:TID:BITS-1:229::LOS;

Input Parameters

<AID>

Access identifier from the "BITS" section.

<TYPEREQ>

(Optional) The type of condition to be retrieved. A null value is equivalent to ALL. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether or not the problem is reported (that is, whether or not it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only


Output Format

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],[<DIRN>],[<DESC>]"
;

Output Example

TID-000 1998-06-20 14:30:00
M 001 COMPLD
"BITS-1,BITS:CR,LOS,SA,01-01,16-02-15,,,\"LOS OF SIGNAL\""
;

Output Parameters

<AID>

Access identifier from the "BITS" section.

<AIDTYPE>

(Optional) Type of access identifier. Specifies the type of facility, link or other addressable entity targeted by the message. The parameter type is MOD2B, which is the alarm type.

1GFC

1-Gigabit Fibre Channel payload

1GFICON

1-Gigabit fiber connectivity payload

2GFC

2-Gigabit Fibre Channel payload

2GFICON

2-Gigabit fiber connectivity payload

4GFC

4-Gigabit Fibre Channel payload

4GFICON

4-Gigabit fiber connectivity payload

BITS

BITS alarm

CLNT

Client facility for MXP/TXP cards

COM

Common alarm

DS3I

DS3i-N-12 alarm

E1

E1 alarm

E100

E100 alarm

E1000

E1000 alarm

E3

E3 alarm

E4

E4 alarm

ENV

ENV alarm

EQPT

EQPT alarm

FSTE

Fast Ethernet port alarm

G1000

G1000 alarm

GIGE

Gigabit Ethernet port alarm

ISC3PEER1G

1-Gbps ISC3 Peer

ISC3PEER2G

2-Gbps ISC3 Peer

ISC3PEER2R

1-Gbps or 2-Gbps ISC3 peer used in transparent (2R) mode

ISCCOMPAT

1-Gbps ISC1, ISC2, and ISC3 compatibility

OCH

Optical channel

OMS

Optical Multiplex Section

OTS

Optical Transport Section

POS

POS port alarm

STM1

STM1 alarm

STM1E

STM1E alarm

STM4

STM4 alarm

STM16

STM16 alarm

STM64

STM64 alarm

SYNCN

SYNCN alarm

TCC

TCC alarm

VC11

VC11 alarm

VC12

VC12 alarm

VC3

VC3 alarm

VC44C

VC44C alarm

VC38C

VC38C alarm

VC464C

VC464C alarm

VC48C

VC48C alarm

VC4

VC4 alarm

VC416C

VC416C alarm

VC42C

VC42C alarm

VC43C

VC43C alarm

<NTFCNCDE>

(Optional) Two-letter notification code. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<TYPEREP>

The type of condition to be retrieved. The parameter type is CONDITION, which is any problem detected on an ONS 15454 SDH or ONS 15600 SDH shelf, whether the problem is reported (that is, whether it generates a trouble notification). Reported conditions include alarms, NA conditions, and NR conditions. See Table 26-1 for a list of conditions.

<SRVEFF>

(Optional) The effect on service caused by the standing alarm or condition. The parameter type is SERV_EFF, with is the effect of the alarm on service.

NSA

The condition is non-service affecting.

SA

The condition is service affecting.

<OCRDAT>

(Optional) Date when the specific event or violation occurred, MM-DD.

<OCRTM>

(Optional) Time when the specific event or violation occurred, HH-MM-SS.

<LOCN>

Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. The parameter type is LOCATION, which is the location where the action is to take place.

FEND

Action occurs on the far end of the facility.

NEND

Action occurs on the near end of the facility.

<DIRN>

The PM count retrieval direction. The parameter type is DIRECTION, which is the transmit and receive directions.

BTH

Both transmit and receive directions

RCV

Receive direction only

<DESC>

(Optional) Condition description. DESC is a string.


21.28  RTRV-COND-ENV

(Cisco ONS 15454 SDH and ONS 15600 SDH) The Retrieve Environmental Condition (RETRV-COND-ENV) command retrieves the environmental conditions.

Usage Guidelines

None

Category

Environment

Security

Retrieve

Input Format

RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>],[<LOCN>],
<DIRN>];

Input Example

RTRV-COND-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR;

Input Parameters

<AID>

Access identifier from the "ENV" section.

Note For RTRV-ALM-ENV, only ENV-IN-{1-4} is a valid AID for ONS 15454 SDH. ENV-OUT-{1,6} is not a valid AID for RTRV-ALM-ENV.

<NTFCNCDE>

(Optional) Two-letter notification code. A null value is equivalent to ALL. The parameter type is NOTIF_CODE, which is the two-character notification code associated with an autonomous message.

CL

The condition causing the alarm has cleared.

CR

A critical alarm.

MJ

A major alarm.

MN

A minor alarm.

NA

The condition is not alarmed.

NR

The alarm is not reported.

<ALMTYPE>

(Optional) The alarm type for the environmental alarm. A null value is equivalent to ALL. The parameter type is ENV_ALM, which is the environmental alarm type.

AIRCOMPR

Air compressor failure

AIRCOND

Air conditioning failure

AIRDRYR

Air dryer failure

BATDSCHRG

Battery discharging

BATTERY

Battery failure

CLFAN

Cooling fan failure

CPMAJOR

Centralized power major failure

CPMINOR

Centralized power minor failure

ENGINE

Engine failure

ENGOPRG

Engine operating

ENGTRANS

Standby engine transfer

EXPLGS

Explosive gas

FIRDETR

Fire detector failure

FIRE

Fire

FLOOD

Flood

FUELLEAK

Fuel leak

FUSE

Fuse failure

GASALARM

Explosive gas, toxic gas, ventilation fail or gas monitor fail

HATCH

CEV hatch fail

GEN

Generator failure

HIAIR

High air flow

HIHUM

High humidity

HITEMP

High temperature

HIWTR

High water

INTRUDER

Intrusion

LEVELCON

Level converter

LVDADSL

Secondary ADSL low voltage disconnect

LVDBYPAS

Low voltage disconnect bypass

LWBATVG

Low battery voltage

LWFUEL

Low fuel

LWHUM

Low humidity

LWPRES