Cisco ONS 15454 SDH TL1 Command Guide, Release 7.2
Chapter 11, ED Commands
Downloads: This chapterpdf (PDF - 1.18MB) The complete bookPDF (PDF - 12.29MB) | Feedback

ED Commands

Table Of Contents

ED Commands

11.1  ED-<GIGE_TYPE>

11.2  ED-<MOD1FCPAYLOAD>

11.3  ED-<MOD1FICONPAYLOAD>

11.4  ED-<MOD2DWDMPAYLOAD>

11.5  ED-<MOD_PATH>

11.6  ED-<MOD_RING>

11.7  ED-<STM_TYPE>

11.8  ED-ALS

11.9  ED-APC

11.10  ED-BITS

11.11  ED-BULKROLL-<STM_TYPE>

11.12  ED-CMD-SECU

11.13  ED-CRS-<PATH>

11.14  ED-DAT

11.15  ED-DS3I

11.16  ED-E1

11.17  ED-E3

11.18  ED-E4

11.19  ED-EQPT

11.20  ED-FAC

11.21  ED-FFP-<MOD2DWDMPAYLOAD>

11.22  ED-FFP-<STM_TYPE>

11.23  ED-FFP-OCH

11.24  ED-FSTE

11.25  ED-G1000

11.26  ED-GFP

11.27  ED-LMP

11.28  ED-LMP-CTRL

11.29  ED-LMP-TLINK

11.30  ED-LMP-DLINK

11.31  ED-LNK

11.32  ED-LNKTERM

11.33  ED-NE-GEN

11.34  ED-NE-PATH

11.35  ED-NE-SYNCN

11.36  ED-OCH

11.37  ED-OCHCC

11.38  ED-OCHNC

11.39  ED-OMS

11.40  ED-OSC

11.41  ED-OTS

11.42  ED-PID

11.43  ED-POS

11.44  ED-PROTOCOL

11.45  ED-ROLL-<MOD_PATH>

11.46  ED-SLV-WDMANS

11.47  ED-STM1E

11.48  ED-SYNCN

11.49  ED-TRAPTABLE

11.50  ED-TRC-OCH

11.51  ED-USER-SECU

11.52  ED-VCG

11.53  ED-WDMANS


ED Commands


This chapter provides edit (ED) commands for the Cisco ONS 15454 SDH.

11.1  ED-<GIGE_TYPE>

The Edit 10GIGE or GIGE (ED-<GIGE_TYPE>) command edits Ethernet facility attributes. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are network element (NE) default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.


Note The following parameters apply only to ED-GIGE; ADMINSTATE, LINKSTATE, MTU, FLOWCTRL, AUTONEG, HIWMRK, LOWMRK, DUPLEX, SPEED, and SOAK.



Note The MACADDR parameter is applicable for ED-10GIGE only.


Category

Ports

Security

Provisioning

Input Format

ED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[ADMINSTATE=<ADMINSTATE>],
[LINKSTATE=<LINKSTATE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>],
[AUTONEG=<AUTONEG>],[HIWMRK=<HIWMRK>],[LOWMRK=<LOWMRK>],
[OPTICS=<OPTICS>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[MACADDR=<MACADDR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[SOAK=<SOAK>]:[<PST>[,<SST>]];

Input Example

ED-GIGE:CISCO:FAC-1-1:123:::ADMINSTATE=DOWN,LINKSTATE=DOWN,MTU=1548,
FLOWCTRL=NONE,AUTONEG=Y,HIWMRK=485,LOWMRK=25,OPTICS=1000_BASE_LX,
DUPLEX=AUTO,SPEED=AUTO,NAME="GIGE PORT",CMDMDE=FRCD,
MACADDR=00-0E-AA-BB-CC-FF,FREQ=1550,LOSSB=SX,SOAK=32:UNLOCKED,
AUTOMATICINSERVICE
;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<ADMINSTATE>

(Optional) The parameter type is UP_DOWN, which indicates an up or down value.

DOWN

Down

UP

Up

<LINKSTATE>

(Optional) The parameter type is UP_DOWN, which indicates an up or down value.

DOWN

Down

UP

Up

<MTU>

(Optional) Maximum transport unit. The parameter type is MTU_TYPE, which indicates the maximum transport unit used by an Ethernet card. Defaults to 9600.

10004

10004. Indicates jumbo size.

1500

1500

1548

1548

9600

9600. Indicates jumbo size.

<FLOWCTRL>

(Optional) Flow control. The parameter type is FLOW, which indicates the type of flow control that has been negotiated for an Ethernet port. Defaults to NONE.

ASYMMETRIC

Asymmetric flow control

ASYMMETRIC_LOCAL

Asymmetric local flow control

NONE

No flow control

PASSTHRU

Passthrough flow control

SYMMETRIC

Symmetric flow control

<AUTONEG>

(Optional) Autonegotiation. The parameter is ON_OFF, which disables or enables an attribute. Defaults to Y.

N

Disable an attribute.

Y

Enable an attribute.

<HIWMRK>

(Optional) High water mark. HIWMRK is an integer. Defaults to 485.

<LOWMRK>

(Optional) Low water mark. LOWMRK is an integer. Defaults to 25.

<OPTICS>

(Optional) The parameter is OPTICS, which indicates the type of Gigabyte Ethernet optics being used.

1000_BASE_CX

1000BaseCX

1000_BASE_LX

1000BaseLX

1000_BASE_SX

1000BaseSX

1000_BASE_ZX

1000BaseZX

100_BASE_FX

100BaseFX

100_BASE_LX

100BaseLX

CWDM_1470

Coarse wavelength division multiplexing (CWDM) 1470

CWDM_1490

CWDM 1490

CWDM_1510

CWDM 1510

CWDM_1530

CWDM 1530

CWDM_1550

CWDM 1550

CWDM_1570

CWDM 1570

CWDM_1590

CWDM 1590

CWDM_1610

CWDM 1610

ITU_100G_1530_33

ITU-100G 1530.33

ITU_100G_1531_12

ITU-100G 1531.12

ITU_100G_1531_90

ITU-100G 1531.90

ITU_100G_1532_68

ITU-100G 1532.68

ITU_100G_1534_25

ITU-100G 1534.25

ITU_100G_1535_04

ITU-100G 1535.04

ITU_100G_1535_82

ITU-100G 1535.82

ITU_100G_1536_61

ITU-100G 1536.61

ITU_100G_1538_19

ITU-100G 1538.19

ITU_100G_1538_98

ITU-100G 1538.98

ITU_100G_1539_77

ITU-100G 1539.77

ITU_100G_1540_56

ITU-100G 1540.56

ITU_100G_1542_14

ITU-100G 1542.14

ITU_100G_1542_94

ITU-100G 1542.94

ITU_100G_1543_73

ITU-100G 1543.73

ITU_100G_1544_53

ITU-100G 1544.53

ITU_100G_1546_12

ITU-100G 1546.12

ITU_100G_1546_92

ITU-100G 1546.92

ITU_100G_1547_72

ITU-100G 1547.72

ITU_100G_1548_51

ITU-100G 1548.51

ITU_100G_1550_12

ITU-100G 1550.12

ITU_100G_1550_92

ITU-100G 1550.92

ITU_100G_1551_72

ITU-100G 1551.72

ITU_100G_1552_52

ITU-100G 1552.52

ITU_100G_1554_13

ITU-100G 1554.13

ITU_100G_1554_94

ITU-100G 1554.94

ITU_100G_1555_75

ITU-100G 1555.75

ITU_100G_1556_55

ITU-100G 156.55

ITU_100G_1558_17

ITU-100G 1558.17

ITU_100G_1558_98

ITU-100G 1558.98

ITU_100G_1559_79

ITU-100G 1559.79

ITU_100G_1560_61

ITU-100G 1560.61

UNKNOWN

Unknown

UNPLUGGED

Unplugged

<DUPLEX>

(Optional) The parameter is ETHER_DUPLEX, which indicates duplex mode. Defaults to AUTO.

AUTO

Auto mode

FULL

Full mode

HALF

Half mode

<SPEED>

(Optional) The parameter type is ETHER_SPEED, which indicates Ethernet speed. Defaults to AUTO.

100_MBPS

100 Mbps

10_GBPS

10 Gbps

10_MBPS

10 Mbps

1_GBPS

1 Gbps

AUTO

Automatic

<NAME>

(Optional) Port name. NAME is a string. Defaults to NULL. Maximum length is 32 characters.

<CMDMDE>

(Optional) Command execution mode. NORM for normal (default) and FRCD for forced. FRCD will override any safeguards that normally reject a request to delete an in service resource.

The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.

FRCD

Force the system to override a state where the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that might make the command fail.

<MACADDR>

(Optional) MACADDR is a string. Defaults to NULL. Maximum length is 18 characters.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN, which indicates the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which indicates the reach values.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer. Defaults to 32.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.2  ED-<MOD1FCPAYLOAD>

The Edit 1GFC, 2GFC, 4GFC, or ESCON (ED-<MOD1FCPAYLOAD>) command edits the attributes related with the Fibre Channel facility. The state Locked,AutomaticInService is not supported on the FC port. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

The port parameters VIZ, LINKRCVRY, DISTEXTN, AUTODETECTION, LINKCREDITS, and MFS can be edited only if the port state is OutofService,Maintenance or OutofService,Disabled.

The port parameters AUTODETECTION, LINKCREDITS, and MFS can be edited only if distance extension is enabled (set to B2B).

When 1GFICON and 2GFICON payloads are provisioned, distance extension=B2B is the default and only valid setting. Setting the distance extension (using the ED-1GFICON, ED-2GFICON, or ED-2GFICON command) to any other setting will be denied with an error message, for example, Provisioning Rules Failed.

Category

Ports

Security

Provisioning

Input Format

ED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],
[DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:[<PST>[,<SST>]];

Input Example

ED-1GFC:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,MFS=2148,NAME="FC PORT",CMDMDE=NORM,SOAK=32,
FREQ=1550,LOSSB=LR-1:LOCKED,MAINTENANCE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.

N

Disable an attribute.

Y

Enable an attribute.

<DISTEXTN>

(Optional) Distance extension. It can be set to Buffer-to-Buffer (B2B) Credit Management state or None. The parameter type is DISTANCE_EXTENSION (distance extension).

Note B2B and link recovery are mutually exclusive. You cannot turn on both B2B and link recovery at the same time.

B2B

Buffer to buffer flow control

NONE

No distance extension

<AUTODETECTION>

(Optional) Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.

N

Disable an attribute.

Y

Enable an attribute.

<LINKCREDITS>

(Optional) Number of link credits. If autodetection is set to off, the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.

<MFS>

(Optional) Maximum frame size. MFS is an integer.

<NAME>

(Optional) NAME is a string.

<CMDMDE>

(Optional) Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<FREQ>

(Optional) Parameter type is OPTICAL_WLEN (optical wavelength).

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) Parameter type is REACH (reach values).

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.3  ED-<MOD1FICONPAYLOAD>

The Edit 1GFICON, 2GFICON, 4GFICON, or ESCON (ED-<MOD1FICONPAYLOAD>) command edits the attributes related with the FICON payload facility. The state Locked,AutomaticInService is not supported on the FICON port. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Ports

Security

Provisioning

Input Format

ED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>,]
[DISTEXTN=<DISTEXTN>,][AUTODETECTION=<AUTODETECTION>,]
[LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][NAME=<NAME>,]
[CMDMDE=<CMDMDE>,][SOAK=<SOAK>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:[<PST>[,<SST>]];

Input Example

ED-1GFICON:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,MFS=2148,NAME="FC PORT",CMDMDE=NORM,SOAK=32,
FREQ=1550,LOSSB=LR-1::LOCKED,MAINTENANCE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<LINKRCVRY>

(Optional) Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.

N

Disable an attribute.

Y

Enable an attribute.

<DISTEXTN>

(Optional) Distance extension. It can be set to B2B Credit Management state or None. The parameter type is DISTANCE_EXTENSION.

Note B2B and link recovery are mutually exclusive. You cannot turn on both B2B and link recovery at the same time.

B2B

Buffer to buffer flow control

NONE

No distance extension

<AUTODETECTION>

(Optional) Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.

N

Disable an attribute.

Y

Enable an attribute.

<LINKCREDITS>

(Optional) Number of link credits. If autodetection is set to off, the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.

<MFS>

Maximum frame size. MFS is an integer.

<NAME>

NAME is a string.

<CMDMDE>

(Optional) Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<FREQ>

(Optional) Parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.4  ED-<MOD2DWDMPAYLOAD>

The Edit 10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, ESCON, ETRCLO, GIGE, HDTV, ISC1, ISC3, or PASSTHRU (ED-<MOD2DWDMPAYLOAD>) command edits the operating parameters for a DWDM client facility. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]];

Input Example

ED-HDTV::FAC-1-1:1:::NAME="PORTNAME",CMDMDE=NORM,FREQ=1550,
LOSSB=LR-1:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<NAME>

(Optional) NAME is a string.

<CMDMDE>

(Optional) Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG. the parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<FREQ>

(Optional) Parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

Parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<PST>

(Optional) Primary state. the parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.5  ED-<MOD_PATH>

The Edit VC3, VC44C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC11, VC12, VC3, VC11, or VC12 (ED-<MOD_PATH>) command edits the attributes associated with VC paths.

Usage Guidelines

The SFBER, SDBER, RVRTV, and RVTM parameters only apply to subnetwork connection protection (SNCP) at the VC path level.

The path trace message is a 64-character string including the terminating carriage return (CR) and line feed (LF) that is transported in the J1 byte of the SDH VC Path overhead.

Both the EXPTRC and TRC string can be provisioned by a user with up to a 62-character string.The EXPTRC parameter indicates that the contents of the expected incoming path trace are provisioned by the user. The TRC parameter indicates the contents of the outgoing path trace message.

The INCTRC parameter indicates the contents of the incoming path trace message.

Path trace has three modes: OFF, MANUAL, and AUTO. The path trace mode defaults to OFF. The MANUAL mode performs the comparison of the received string with the user-entered expected string. The AUTO mode performs the comparison of the present received string with an expected string set to a previously received string. If there is a mismatch, TIM-P alarm is raised. When the path trace mode is in OFF mode, there is no path trace processing, and all the alarm and state conditions are reset.

The TACC parameter edits an existing single VC or VT and changes it to a test access point. When an editing command on TACC is executed, it assigns the VC or VT for the first two-way connection and VC+1 as the second 2-way connection. For single facility access digroup (FAD) test access, only a single VC/VT is used for the TAP creation. For more information on TACC, refer to the Cisco ONS SONET TL1 Reference Guide.

J1 is implemented on the on E1, E3, E4, DS3i-N-12, and STM cards.

STM4, STM16, E100, and E1000 cards do not support path trace.

The STM1, STM16AS, and STM64 cards only support EXPTRC in the ED-VC-PATH command.


Note Each TL1 command must be less than or equal to 255 characters. Any command larger than 255 characters must be split into multiple commands. For example, if you use the ED-<VC_PATH> command to edit the J1 EXPTRC/TRC message, SNCP attributes, and TACC attributes and the command exceeds 255 characters, the command will not be processed. You must use multiple ED-<VC_PATH> commands instead.


The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

The following actions will return error messages:

Sending this command to edit SFBER, SDBER, RVRTV or RVTM for the non-SNCP VC path.

Sending this command to edit the EXPTRC string with the AUTO path trace mode (TRCMODE=AUTO).

Sending this command to edit both TACC and any other attribute(s) will return the "Parameters Not Compatible" error message.

Sending this command to edit TACC on an AID with cross-connects will return the "VC in Use" error message.

This command is allowed to edit EXPTRC on STM1, STM16AS, and STM64 cards.


NoteTACC creation will be denied on protect ports and cards in 1:1, 1:N, and 1+1 configurations.

The VFAC AID is only valid on slots containing an ML-Series card. TACC is not supported for the ML-Series cards.

After the MS-SPRing switching, provisioning of the J1 trace string or trace mode is not allowed on the protection path.

TACC creation is allowed on protection channel access (PCA) for two-fiber and four-fiber MS-SPRing.

TACC is not supported on G1000, MXP_2.5_10G, TXP_MR_10G, ML1000-2, and ML100T-12 cards.

HOLDOFFTIMER is not specific to a path. It is applicable to the SNCP selector. If HOLDOFFTIMER is changed on one path associated with the selector, the HOLDOFFTIMER of the other path associated with the same selector is also changed.

The cross-connects on the DS3i-N-12 card are VC4 width, but the individual VC1s within the 3C will be accessible. For editing the path attributes, use ED-VC3 with the FAC AID. For test access creation, use ED-VC4 because the test access path width (like the cross-connect) has to be 3C on the DS3i-N-12 card, which creates a new entity (TAP) on the DS3i-N-12 card in 3C width. On the DS3i-N-12 card, the ED-VC command can be used either with VC3 or VC4 modifier depending on the parameter to be modified.

For the selector path on an MS-SPRing, the SWPDIP is not editable and is always in ON state. If an attempt is made to edit SWPDIP on a selector path with an MS-SPRing, an error message will be returned.


Category

Paths

Security

Provisioning

Input Format

ED-<MOD_PATH>:[TID]:<AID>:[CTAG]:::[SFBER=<SFBER>],[SDBER=<SDBER>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SWPDIP=<SWPDIP>],
[HOLDOFFTIMER=<HOLDOFFTIMER>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],
[TRCMODE=<TRCMODE>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-VC3C:FERNDALE:VC-2-1-4:115:::SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
SWPDIP=Y,HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
TRCMODE=OFF,TACC=8,TAPTYPE=SINGLE,CMDMDE=NORM:UNLOCKED,
AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "CrossConnectId1" section.

<SFBER>

(Optional) Signal failure threshold. Applies only to SNCP. Applies to VC4-level paths. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold. Applies only to SNCP. Applies to VC4-level paths (VCn). The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<RVRTV>

(Optional) Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to SNCP. The parameter type is ON_OFF, which disables or enables an attribute.

N

Disable an attribute.

Y

Enable an attribute.

<RVTM>

(Optional) Revertive time. RVTM is not allowed to be set while RVRTV is N. Only applies to SNCP. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<SWPDIP>

(Optional) On-off switch for SNCP payload defect level switching. Applicable only to VC-level paths in SDH (VCn). The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<HOLDOFFTIMER>

(Optional) Hold-off timer for SNCP DRI. Values must be within 0 and 10000 milliseconds (0 to 10 seconds), with increments of 100 milliseconds. HOLDOFFTIMER is an integer.

<EXPTRC>

(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR and LF. Applicable to VC-level paths in SDH (VCn). EXPTRC is a string.

<TRC>

(Optional) The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. A null value defaults to the NE transmitting null characters (Hex 00). Applicable to VC-level paths in SDH (VCn). TRC is a string.

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level paths in SDH (VCn). Defaults to the OFF mode. The parameter type is TRCMODE (trace mode).

AUTO

Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.

AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on alarm indication signal (AIS) and remote defect indication (RDI) if TIM-P is detected.

MAN

Use the provisioned expected string as the expected string.

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

OFF

Turn off path trace capability. Nothing will be reported.

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.

<TAPTYPE>

(Optional) TAP type. the parameter type is TAPTYPE (test access point type).

DUAL

Dual FAD

SINGLE

Single FAD

<CMDMDE>

(Optional) Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. the parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.6  ED-<MOD_RING>

The Edit Multiplex Section-Shared Protection Ring (ED-<MOD_RING>) command edits the MS-SPRing attributes.

Usage Guidelines

The RVRTV, RVTM, SRVRTV, SRVTM, NODEID, and RINGID attributes can be edited for the four-fiber MS-SPRing.

The RVRTV, RVTM, NODEID, and RINGID attributes can be edited for the two-fiber MS-SPRing.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

The following actions will produce errors:

If the system fails on getting IOR, a SROF (Get IOR Failed) error message is returned

If the AID is invalid, an IIAC (Invalid AID) error message is returned.

If the MS-SPRing does not exist, a SRQN (MSSPR Does Not Exist) error message is returned.

The SROF (Facility Not Provisioned) or SROF (Cannot Access MSSPR) error message will be returned for an invalid query.

The SRQN (MSSPR Edition Failed) error message is returned for an invalid edition query.

Sending this command to modify SRVRTV or SRVTM on a two-fiber MS-SPRing will return an IDNV (Invalid Data For 2F-MS-SPRing) error message.

Sending this command to modify the node ID with invalid data will return an IIAC (Invalid NodeId) error message.

Sending this command to change the ring ID into invalid data will return an IIAC (Invalid RingId) error message.

Changing the MS-SPRing node ID with a duplicated ID will return a SROF (Cannot Set NodeId) error message.

Changing the MS-SPRing ring ID with a duplicated ID will return a SROF (Cannot Set RingId) error message.


NoteThe ALL AID is invalid for this command.

The list AID format is supported in Release 4.6 and later.


Category

MS-SPRing

Security

Provisioning

Input Format

ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>][:];

Input Example

ED-BLSR:PETALUMA:MSSPR-43:123:::RINGID=43,NODEID=3,RVRTV=Y,RVTM=2.0,
SRVRTV=Y,SRVTM=5.0;

Input Parameters

<AID>

Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE. ALL or MSSPR-ALL AID is not allowed for editing an MS-SPRing.

<RINGID>

The MS-SPRing ID of the NE, up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.

<NODEID>

The MS-SPRing node ID of the NE. NODEID ranges from 0 to 31. NODEID is an integer.

<RVRTV>

Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

RVTM

Revertive time. RVTM is not allowed to be set while "RVRTV" is N. the parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<SRVRTV>

The span revertive mode for four-fiber MS-SPRing only. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<SRVTM>

The span revertive time for four-fiber MS-SPRing only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.


11.7  ED-<STM_TYPE>

The Edit STM1, STM4, STM16, or STM64 command edits the attributes (for example, service parameters) and state of an STM facility. Allowable states for a facility are Locked, Locked with Automatic In Service transitioning, Locked for Maintenance, and Unlocked. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The OPRNOMINAL parameter is supported only by optical card types that support Optical PM. The following cards support OPRNOMINAL: STM1-8, MRC-12, MRC-12-2.5G, MRC-4-2.5G, STM64-XFP, CTX-2500, CTX, STM64-4, STM16-16, STM64-4-DWDM, ASAP-4.

The data communications channel (DCC) transmit is bridged to both working and protect in a 1+1 configuration. On the receive side, the active one is selected for DCC. The DCC is provisioned on the working port only in a 1+1 configuration.

All lines in a 1+1 MS-SPRing must have the same mode. If you change the mode of a line that is in a 1+1 MS-SPRing, an error message will be returned.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

UNI-C DCC provisioning notes:

The attributes DCC (Y/N) and mode (SONET/SDH) remain the same in the ED/RTRV-STM commands when the DCC is used for UNI-C, in which case the port attribute UNIC is enabled (UNIC=Y).

UNI-C DCC termination cannot be deleted by the regular DCC de-provisioning command.

If the DCC is created under regular SDH provisioning, and this port is used by UNI-C, the port is converted as a UNI-C DCC automatically.

Unprovisioning UNI-C IF/IB IPCC will free up DCC termination automatically.

MS-DCC/RS-DCC terminations cannot be unprovisioned if a provisionable patchcord termination endpoint is provisioned on the port.

J0 support (EXPTRC, TRC, TRCMODE, and TRCFORMAT parameters) is supported only by dense wavelength division multiplexing (DWDM) cards with an STM payload. J0 is not supported by STM1-8, STM4, STM16, STM64, and other SDH optical cards.

Category

Ports

Security

Provisioning

Input Format

ED-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>],[AREA=<AREA>],
[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[MUX=<MUX>],
[SOAK=<SOAK>],[OSPF=<OSPF>],[MSDCC=<MSDCC>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>],[SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>],[FOREIGNIP=<FOREIGNIP>],OPRNOMINAL=<OPRNOMINAL>]:[<PST>[,<SST>]];

Input Example

ED-STM16:PENNGROVE:FAC-6-1:114:::DCC=Y,AREA=10.92.63.1,SYNCMSG=N,SENDDUS=N,
PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,MUX=E2,SOAK=10,OSPF=Y,
MSDCC=N,NAME="STMPORT",CMDMDE=NORM,EXPTRC="AAA",TRC="AAA",
TRCMODE=MAN,TRCFORMAT=16-BYTE,ADMSSM=G811,SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=N,
FOREIGNIP="IPADDRESS",OPRNOMINAL=Y:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<DCC>

(Optional) Indicates whether or not the RS-DCC is to be used. Identifies the RS-DCC connection of the port. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<AREA>

(Optional) The area ID shows up only if the DCC is enabled. String

<SYNCMSG>

(Optional) Synchronization status message. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<SENDDUS>

(Optional) Whether the facility will send the Do Not Use for Synchronization (DUS) value as the synchronization status message for that facility. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<PJMON>

(Optional) Identifies an STM port PJMON. PJMON is an integer. It defaults to 0 (zero). Set a valid VC4 number of the optical port.

Note The PJMON number displayed in TL1 interface does not correspond to the PJVC4MON number in CTC, but instead corresponds to the VC4 number of the optical port.

<SFBER>

(Optional) Signal failure threshold. the parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold. the parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5

1E-6

SDBER is 1E-6

1E-7

SDBER is 1E-7

1E-8

SDBER is 1E-8

1E-9

SDBER is 1E-9

<MODE>

(Optional) STM port mode. The parameter type is OPTICAL_MODE, which is the facility's optical mode.

SINGLESHELF

The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.

MULTISHELF

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.

MULTISHELFETH

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.

<MUX>

(Optional) MS-SPRing extension byte (supported only on the STM16AS card). The parameter type is MUX_TYPE, which is the MS-SPRing extension type.

E2

E2 byte (orderwire)

F1

F1 byte (user)

K3

K3 byte

Z2

Z2 byte

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<OSFP>

(Optional) The Open Shortest Path First discovery. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<MSDCC>

(Optional) The MS-DCC connection on the port. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<NAME>

(Optional) NAME is a string.

<CMDMDE>

(Optional) Command mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from Unlocked-Enabled or Locked-Disabled, AutomaticInService service status. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied

NORM

Execute the command normally. Do not override any conditions that could make the command fail

<EXPTRC>

(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). String

<TRC>

(Optional) The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. Defaults to NULL. TRC is a string.

<TRCMODE>

(Optional) Path trace mode. Applicable only to VC-level paths in SDH (VCn). Defaults to the MAN mode. The parameter type is TRCMODE (trace mode)

AUTO

Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.

AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

MAN

Use the provisioned expected string as the expected string.

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

OFF

Turn off path trace capability. Nothing will be reported.

<TRCFORMAT>

(Optional) Trace message size. The parameter type is TRCFORMAT (trace format).

1-BYTE

1 byte trace message

16-BYTE

16 byte trace message

64-BYTE

64 byte trace message

<ADMSSM>

(Optional) SSM selectable value. It will only appear when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

DUS_SDH

Do Not Use For Synchronization

G811

G811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

G812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

G812TL Standard

SETS

Synchronous Equipment Timing Source

<SENDDUSFF>

(Optional) The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<AISONLPBK>

(Optional) The parameter type is AIS_ON_LPBK, which indicates if AIS should be sent on loopback.

AIS_ONLPBK_FACILITY

AIS is sent on facility loopback.

AIS_ON_LPBK_ALL

AIS is sent on all loopbacks.

AIS_ON_LPBK_OFF

AIS is not sent on loopback.

AIS_ON_LPBK_TERMINAL

AIS is sent on terminal loopback.

<FREQ>

(Optional) The parameter type is OPTICAL_WLEN (optical wavelength).

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<LOSSB>

(Optional) The parameter type is REACH, which is the reach value.

AUTOPROV

Autoprovisioning

CX

Reach CX

DX

Reach DX

HX

Reach HX

I1

Reach I1

IR-1

Reach IR-1

IR-2

Reach IR-2

L1

Reach L1

L2

Reach L2

L3

Reach L3

LR-1

Reach LR-1

LR-2

Reach LR-2

LR-3

Reach LR-3

LX

Reach LX

S1

Reach S1

S2

Reach S2

SR

Reach SR

SR-1

Reach SR-1

SX

Reach SX

T

Reach T

VX

Reach VX

ZX

Reach ZX

<FOREIGNFEND>

(Optional) Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF (disable or enabled an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<FOREIGNIP>

(Optional) The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGNIP is a string.

<OPRNOMINAL>

Reads the current raw optical receive power and sets the raw OPR value as the nominal optical receive power.

N

Not Supported.

Y

Sets the OPR.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. Defaults to AUTOMATICINSERVICE. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.8  ED-ALS

The Edit Automatic Laser Shutdown (ED-ALS) command is used to modify the automatic laser shutdown (ALS) attributes of an STM facility and all the facilities that support the ALS feature. For MXP_2.5G_10E, TXP_MR_10E, MXP_2.5G_10G, TXP_MR_10G, TXP_MR_2.5G, and TXPP_MR_2.5G cards, this command is used to modify the ALS parameter of the STM16 and STM64 ports.

Usage Guidelines

None

Category

Ports

Security

Provisioning

Input Format

ED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>][:];

Input Example

ED-ALS:CISCO:FAC-1-1:100:::ALSMODE=AUTO,ALSRCINT=130,ALSRCPW=35.1;

Input Parameters

<SRC>

Access identifier from the "AidUnionId" section.

<ALSMODE>

(Optional) ALS is enabled or disabled. the parameter type is ALS_MODE, which is the working mode for automatic laser shutdown.

AUTO

Automatic

DISABLED

Disabled

MAN

Manual

MAN-RESTART

Manual restart for test

<ALSRCINT>

(Optional) ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer.

<ALSRCPW>

(Optional) ALS recovery pulse width. The range is 80.0 to 100.00 seconds, in increments of 100 ms. ALSRCPW is a float.


11.9  ED-APC

The Edit Amplification Power Control (ED-APC) command is used to modify the APC application attributes. The default value for an optional parameter is the NE default value. The value might not be the current value for the parameter. Issue the RTRV-xx command to retrieve the current value.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

ED-APC:[<TID>]::<CTAG>[:::APCENABLE=<APCENABLE>];

Input Example

ED-APC:PENNGROVE::CTAG:::APCENABLE=N;

Input Parameters

<APCENABLE>

(Optional) Enable/disable the APC application. Default is N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.


11.10  ED-BITS

The Edit Building Integrated Timing Supply (ED-BITS) command edits the building integrated timing supply (BITS) reference attributes.

Usage Guidelines

The SYNC-BITS1 and SYNC-BITS2 AIDs can be used to set the BITS-OUT port state. For a BITS facility, 2 M, 64 K, and E1 are only applicable to ONS 15600 SDH.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Synchronization

Security

Provisioning

Input Format

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>];

Input Example

ED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,
AISTHRSHLD=G811,SABIT=BYTE-5,BITSFAC=E1,ADMSSM=G811:UNLOCKED;

Input Parameters

<AID>

Access identifier from the "BITS" section.

<LINECDE>

(Optional) Line code. The parameter type is LINE_CODE (line code).

AMI

Line code value is AMI.

B8ZS

Line code value is bipolar with eight-zero substitution.

HDB3

Line Code HDB3. Only applicable to SDH E1 signal.

<FMT>

(Optional) Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.

D4

D4 frame format

E1-CRCMF

SDH E1 CRCMF frame format

E1-MF

SDH E1 MF frame format

E1-UNFRAMED

SDH E1 unframed format

ESF

ESF frame format

UNFRAMED

Frame format is unframed.

<LBO>

(Optional) Line buildout settings. BITS line buildout. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line buildout).

0-133

BITS line buildout range is 0-133.

134-266

BITS line buildout range is 134-266.

267-399

BITS line buildout range is 267-399.

400-533

BITS line buildout range is 400-533.

534-655

BITS line buildout range is 534-655.

<SYNCMSG>

(Optional) Indicates whether the BITS facility supports synchronization status message. Default is on (Y). The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol.

Y

The ring does support the extended K1/K2/K3 protocol.

<AISTHRSHLD>

(Optional) Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

DUS_SDH

Do Not Use For Synchronization

G811

G811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

G812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

G812TL Standard

SETS

Synchronous Equipment Timing Source

<SABIT>

(Optional) When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).

BYTE-4

SABIT is BYTE-4.

BYTE-5

SABIT is BYTE-5.

BYTE-6

SABIT is BYTE-6.

BYTE-7

SABIT is BYTE-7.

BYTE-8

SABIT is BYTE-8.

<BITSFAC>

(Optional) BITS facility settings. BITS-2 always inherits the value of BITS-1. The parameter type is BITS_FAC, which is the BITS facility rate.

Note 2 M, 64 K, and E1 are only applicable to ONS 15600 SDH.

2 M

2 MHz rate

64 K

64 K rate

6 M

6 MHz rate

E1

E1 rate

<ADMSSM>

(Optional) SSM selectable. Only applicable to BITS-IN when SSM is disabled. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SDH.

Note Not applicable to ONS 15600 SDH.

DUS_SDH

Do Not Use For Synchronization

G811

G811 Standard

RES_SDH

Reserved For Network Synchronization Use

G812T

G812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

G812TL Standard

SETS

Synchronous Equipment Timing Source

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service


11.11  ED-BULKROLL-<STM_TYPE>

The Edit Bulkroll for STM4, STM64, STM1, and STM16 command edits information about the rolling of traffic from one endpoint to another without interrupting service. This uses the FORCE option to force a valid signal. The only parameters that can be edited are RMODE and FORCE. The time slots cannot be edited. Use ED-ROLL-<MOD_PATH> for single path level rolling. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

ED-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RTOSTART=<RTOSTART>],
[RFROMEND=<RFROMEND>],[CMDMDE=<CMDMDE>];

Input Example

ED-BULKROLL-STM16:CISCO:FAC-1-1:1:::RFROMSTART=VC4-1-1-1,
RTOSTART=VC4-1-1-1,RFROMEND=VC4-1-1-1,CMDMDE=FRCD;

Input Parameters

<FROM>

One of the end points. Access identifier from the "FACILITY" section for line level rolling and bulk rolling. Must not be null.

<RFROMSTART>

(Optional) The starting time slot in the source roll port. For bulk rolling only. A null value is equal to ALL

Parameter type is PATH—modifier for path commands

VC3

Synchronous Transport Signal/Module Level-1 (51 Mbps)

VC44C

Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps)

VC464C

Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps)

VC48C

Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps)

VC4

Synchronous Transport Signal/Module Signal Level-3 Concatenated (155 Mbps)

VC416C

Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps)

VC42C

Synchronous Transport Signal/Module Level-6 (310 Mbps)

VC43C

Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps)

VC11

Virtual Channel 11

VC12

Virtual Channel 12

<RFROMEND>

(Optional) The ending time slot in the source roll port. For bulk rolling only. A null value is equal to ALL. The parameter type is PATH, which is the modifier for path commands.

VC3

Synchronous Transport Signal/Module Level-1 (51 Mbps)

VC44C

Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps)

VC464C

Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps)

VC48C

Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps)

VC4

Synchronous Transport Signal/Module Signal Level-3 Concatenated (155 Mbps)

VC416C

Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps)

VC42C

Synchronous Transport Signal/Module Level-6 (310 Mbps)

VC43C

Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps)

VC11

Virtual Channel 11

VC12

Virtual Channel 12

<CMDMDE>

(Optional) Command execution mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.


11.12  ED-CMD-SECU

The Edit Command Security (ED-CMD-SECU) command edits the command security level of a particular command.

Usage Guidelines

None

Category

Security

Security

Superuser

Input Format

ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;

Input Example

ED-CMD-SECU::INIT-REG:1::SUPER;

Input Parameters

<AID>

Access identifier string. Identifies the entity in the NE to which the command pertains. It is the command verb along with verb modifier(s), as it currently exists. It can be a single command or a block of commands, where the block could include all commands. Only INIT-REG will be supported. AID is a string. It must not be null.

<CAP>

Command access privilege. It must not be null. The parameter type is PRIVILEGE, which is the security level.

PROV

Provision security level. 60 minutes of idle time.

SUPER

Superuser security level. 15 minutes of idle time.


11.13  ED-CRS-<PATH>

The Edit Cross-Connection for VC3, VC44C, VC38C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (ED-CRS-<PATH>) command edits a cross-connect. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

ADD and REMOVE cannot be used together. The example provided is for informational purposes only. ADD and REMOVE are mutually exclusive.

Add/Remove drops is possible only on ONEWAY, SNCP_DROP, SNCP_DC, and SNCP_EN type of cross-connects (one-way only).

Traditional cross-connections cannot be upgraded to DRI cross-connections using the ED_CRS command.

CKTID is a string of ASCII characters. The maximum length of CKTID is 48. If the CKTID is EMPTY or NULL, this field will not appear.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

You cannot add or drop onto unidirectional connections on MS-SPRing DRI primary or secondary nodes.

Category

Cross Connections

Security

Provisioning

Input Format

ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]:[ADD=<ADD>],
[REMOVE=<REMOVE>],[CKTID=<CKTID>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-CRS-VC4::VC4-1-1-1,VC4-2-1-1:1:::ADD=VC4-13-1-1,REMOVE=VC4-2-1-1,CKTID=CKTID
CMDMDE=FRCD:UNLOCKED,AUTOMATICINSERVICE;

<SRC>

Source AID from the "CrossConnectId1" section.

<DST>

Destination AID from the "CrossConnectId1" section.

<CCT>

(Optional) Type of connection. Used for specifying one or two-way connections. The parameter type is CCT, which is the type of cross-connect to be created.

1WAY

A unidirectional connection from a source tributary to a destination tributary.

1WAYDC

SNCP multicast drop (1-way continue)

1WAYEN

SNCP multicast end node (1-way continue)

1WAYMON

A bidirectional connection between the two tributaries

Note 1WAYMON is not supported with TL1. However, it is still supported from Cisco Transport Controller (CTC). Using CTC, you can create 1WAYMON cross-connects and can be retrieved through TL1.

1WAYPCA

A unidirectional connection from a source tributary to a destination tributary on the protection path/fiber

2WAY

A bidirectional connection between the two tributaries

2WAYDC

A bidirectional drop-and-continue connection applicable only to SNCP traditional and integrated DRIs.

2WAYPCA

A bidirectional connection between the two tributaries on the extra protection path/fiber.

DIAG

Diagnostics cross-connect. Supports BERT (MS-SPRing PCA diagnostics cross-connect).

<ADD>

(Optional) AID from the "AidUnionId" section.

<REMOVE>

(Optional) AID from the "AidUnionId" section.

<CKTID>

(Optional) Circuit identification that contains the common language Circuit ID or other alias of the circuit being provisioned. Cannot contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<CMDMDE>

(Optional) Command mode. The FRCD mode of operation is applicable only if the PST=Locked and SST=Unlocked. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


Input Parameters

11.14  ED-DAT

The Edit Date and Time (ED-DAT) command edits the date and time.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>];

Input Example

ED-DAT:CISCO::1234::99-12-21,14-35-15;

Input Parameters

<DATE>

(Optional) Date. DATE is a string.

<TIME>

(Optional) Time. TIME is a string.


11.15  ED-DS3I

The Edit DS3I (ED-DS3I) command edits the attributes of a DS3i-N-12 facility.

Usage Guidelines

The following actions will return error messages:

Sending this command to edit TACC and any other attribute while the port has a cross-connection or the port/VT has a test access point (TAP or TACC Number) will return the IPNC (Parameters Not Compatible) error message.

Editing the TACC through the ED-xxx command is only allowed if there are no circuits or cross-connects on the port and the port or VT does not have a test access point (TAP or TACC Number). Otherwise, an error message will be returned.


NoteThis command is not allowed if the card is a protect card. TACC creation will be denied on protect ports/cards.

Automatic application of loopbacks originating from the far end can be inhibited on the ports of a DS3i-N-12 card.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.


Category

Ports

Security

Provisioning

Input Format

ED-DS3I:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>],[LINECDE=<LINECDE>],[LBO=<LBO>],
[INHFELPBK=<INHFELPBK>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>],
[SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-DS3I:CISCO:FAC-1-2:1:::FMT=C-BIT,LINECDE=B8ZS,LBO=0-255,INHFELPBK=N,
TACC=8,TAPTYPE=SINGLE,SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="DS3I PORT",
CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<FMT>

(Optional) Digital signal format. Defaults to C-BIT. The parameter type is DS_LINE_TYPE, which is the DS123 line type.

C-BIT

C-BIT line type applies to the DS3i-N-12 cards.

M13

M13 line type applies to the DS3i-N-12 cards.

UNFRAMED

Line type is unframed.

<LINECDE>

(Optional) Line code. Defaults to B8ZS. The parameter type is DS_LINE_CODE.

AMI

Line code value is AMI.

B8ZS

Line code value is B8ZS.

HDB3

Line code value is HDB3.

<LBO>

(Optional) Line buildout settings. LBO is an integer. Defaults to 0-255. The parameter type is E_LBO, which is the electrical signal line buildout.

0-225

Electrical signal line buildout range is 0-225.

226-450

Electrical signal line buildout range is 226-450.

<INHFELPBK>

(Optional) Far-end loopback inhibition attribute of the port. If it is Y, the automatic far-end loopbacks are inhibited. It is either on or off. Defaults to Y. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.

<TAPTYPE>

(Optional) TAP type. The parameter type is TAPTYPE, which is the test access point type.

DUAL

Dual FAD

SINGLE

Single FAD

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32. SOAK is an integer.

<NAME>

(Optional) Maximum length is 32 characters. NAME is a string. Defaults to Null.

<CMDMDE>

(Optional) Command mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.16  ED-E1

The Edit E1(ED-E1) command edits the attributes of an E1 facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Sending this command to edit TACC and any other attribute while the port has a cross-connect or the port/VT has a test access point (TAP or TACC Number), will return the IPNC (Parameters Not Compatible) error message.


Note TACC creation will be denied on the protect ports/cards.



Note ADMSSM, RETIME, SABIT, SYNCMSG, and SENDDUS parameters are only supported on the DS1/E1-56 card.


Category

Ports

Security

Provisioning

Input Format

ED-E1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[TACC=<TACC>],
[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SYNCMSG=<SYNCMSG>],
[SENDDUS=<SENDDUS>],[RETIME=<RETIME>],[ADMSSM=<ADMSSM>],
[SABIT=<SABIT>]:[<PST>[,<SST>]];

Input Example

ED-E1:CISCO:FAC-2-1:1:::LINECDE=HDB3,FMT=E1-MF,TACC=8,TAPTYPE=SINGLE,
SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="E1 PORT",CMDMDE=NORM,
SYNCMSG=N,SENDDUS=N,RETIME=Y,ADMSSM=STU_SDH,
SABIT=BYTE-4:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<LINECDE>

(Optional) Line code. Defaults to HDB3. The parameter type is LINE_CODE (line code).

AMI

Line code value is AMI.

B8ZS

Line code value is B8ZS.

HDB3

Line code value is HDB3.

<FMT>

(Optional) Digital signal frame format. Defaults to E1-MF. The parameter type is FRAME_FORMAT, which is the frame format for an E1 port.

D4

Frame format is D4

E1-CRCMF

SDH E1 CRCMF frame format

E1-MF

SDH E1 MF frame

E1-UNFRAMED

SDH E1 unframed format

ESF

Frame format is ESF

UNFRAMED

Frame format is unframed

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Default is N. TACC is an integer.

<TAPTYPE>

(Optional) TAP type. Defaults to DUAL. The parameter type is TAPTYPE, which is the test access point type.

DUAL

Dual FAD

SINGLE

Single FAD

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32. SOAK is an integer.

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

<CMDMDE>

(Optional) Command mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<SYNCMSG>

(Optional) Synchronization status messaging is enabled or disabled on the E1 facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

No

Y

Yes

<SENDDUS>

(Optional) The facility will send the DUS value as the synchronization status message for that facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

No

Y

Yes

<RETIME>

(Optional) Indicates if retiming is needed. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

No

Y

Yes

<ADMSSM>

(Optional) The administrative synchronization status message. Defaults to STU_SDH. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level.

DUS

Do Not Use For Synchronization

PRS

Primary Reference Source, Stratum 1 Traceable

DUS_SDH

Do Not Use For Synchronization

G811

G811 Standard

G812T

G812T Standard

STU_SDH

Synchronized, Traceability Unknown

G812TL

G812TL Standard

SETS

Synchronous Equipment Timing Source

<SABIT>

(Optional) When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).

BYTE-4

SABIT is BYTE-4.

BYTE-5

SABIT is BYTE-5.

BYTE-6

SABIT is BYTE-6.

BYTE-7

SABIT is BYTE-7.

BYTE-8

SABIT is BYTE-8.

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.17  ED-E3

The Edit E3 (ED-E3) command edits the attributes of an E3 facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Sending this command to edit TACC and any other attribute while the port has a cross-connect or the port or VT has a test access point (TAP or TACC Number) will return the IPNC (Parameters Not Compatible) error message.


Note TACC creation will be denied on the protect ports and cards.


Category

Ports

Security

Provisioning

Input Format

ED-E3:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-E3:CISCO:FAC-1-2:1:::TACC=8,TAPTYPE=SINGLE,SFBER=1E-4,SDBER=1E-6,SOAK=10,
NAME="E3 PORT",CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<TACC>

(Optional) TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Default is N. TACC is an integer.

<TAPTYPE>

(Optional) TAP type. Defaults to DUAL. The parameter type is TAPTYPE, which is the test access point type.

DUAL

Dual FAD

SINGLE

Single FAD

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals.Defaults to 32. SOAK is an integer.

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

<CMDMDE>

(Optional) Command mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.18  ED-E4

The Edit E4 (ED-E4) command edits the attributes of an E4 facility. Currently this is only applicable to STM1E Ports 9 to 12 when they are in E4-FRAMED or E4-UNFRAMED mode.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Ports

Security

Provisioning

Input Format

ED-E4:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-E4:CISCO1:FAC-6-1:114:::SFBER=1E-4,SDBER=1E-6,SOAK=10,NAME="E4 PORT",
CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<SFBER>

(Optional) Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals.Defaults to 32. SOAK is an integer.

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

<CMDMDE>

(Optional) Command mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.19  ED-EQPT

The Edit Equipment (ED-EQPT) command edits the attributes for a given equipment slot in the NE. If the card is in an equipment slot, this command is allowed only on the working AID.

The ED-EQPT command also modifies a shelf role from NC to SC on an NE configured in multishelf mode.

Usage Guidelines

The PROTID parameter indicates the unique identifier of the protection group (the protect card). "NULL" is a special value of the PROTID parameter and indicates absence of a protection group. For the 1:1 protection type, RVRTV and RVTM parameters can be changed. For the 1:1 protection type, if the PROTID parameter is entered as "NULL", the protection group is deleted, as shown in the following example:

ED-EQPT:[<TID>]:SLOT-2:<CTAG>:::PROTID=NULL;

For the 1:N protection type, if the PROTID is "NULL", the AIDs in the list are removed from the protection group. If all the working cards are in the AID list, the protection group is deleted.

For example, if Slot 1, Slot 2, and Slot 4 were the only working cards in the protection group, the following command will remove Slot 4 from the protection group:

ED-EQPT:[<TID>]:SLOT-4:<CTAG>:::PROTID=NULL;

The protection group still has Slot 1 and Slot 2 as working cards.

The following command will remove all the other working cards in the preceding example and consequently delete the protection group itself:

ED-EQPT:[<TID>]:SLOT-2&SLOT-1:<CTAG>:::PROTID=NULL;

The ED-EQPT command can be successfully executed on an already provisioned card to add or remove a working card from a protection group. This command is not valid on a protect card. Only cards can be added to or removed from a protection group. Protection type is immutable and is determined at the time of creation of a protection group (while adding the first working card). After it is provisioned, the equipment type cannot be edited either.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

The following examples show how to add an existing card to a protection group using the ED-EQPT command:

1:1 protection group:

ED-EQPT::SLOT-2:12:::PROTID=SLOT-1,RVRTV=Y,RVTM=9.0;

1:N protection group:

ED-EQPT::SLOT-2:12:::PROTID=SLOT-3,PRTYPE=1-N,RVTM=6.5;

Error conditions for editing a 1:1 or 1:N protection group could be:

Editing the PRTYPE or PROTID (non-NULL value) parameters.

Editing RVRTV or RVTM when no protection group exists.

Editing RVRTV for 1:N protection.

Failed to remove, currently switched to protect.

The DS3i-N-12 card's provisioning is based on the cross-connect type and the DS3i-N-1 card's location. CARDMODE provisioning is allowed on the DS3i-N-12 and ML-Series cards as follows:

The DS3i-N-12 card in the lower speed I/O slot with the cross-connect card only allows the DS3I-VC32 CARDMODE. Other cases allow the CARDMODE to be DS3I-VC-4-16.

There is no card reboot if the CARDMODE is changed on the DS3i-N-12 card.

The DS3i-N-12 card can be upgraded or downgraded by changing the CARDMODE with the ED-EQPT command.

CMDMDE provisioning behaves as follows:

If the command mode (CMDMDE) is set to forced (FRCD) during the creation of a 1:1 or 1:N protection group, all cards must be physically plugged in and in the service state (Unlocked). If the cards are not physically plugged in, then the command is denied with an appropriate error message. When the command mode is set to normal (NORM) (the default), the cards do not have to be physically plugged in and in the service state.

If the command mode is set to forced (FRCD) during the removal of a card in a 1:1 or 1:N protection group, there must be no cross-connects (for example, services) present on the card. If there are cross-connects present on the card, the command is denied with an appropriate error message. If the command mode is set to normal (NORM) (the default), it does not require that cross-connects be deleted on the card.

On the FC_MR-4 card, the card mode cannot be changed to FCMR-LINERATE when the payload on any port is 1GFICON or 2GFICON. These payloads are allowed only in Distance Extension Card Mode.

Category

Equipment

Security

Provisioning

Input Format

ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[PRTYPE=<PRTYPE>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[CMDMDE=<CMDMDE>],
[CARDMODE=<CARDMODE>],[PEERID=<PEERID>],[REGENNAME=<REGENNAME>],
[PWL=<PWL>],[RETIME=<RETIME>],[SHELFROLE=<SHELFROLE>],
[NEWSHELFID=<NEWSHELFID>]:[<PST>[,<SST>]];

Input Example

ED-EQPT:CISCO:SLOT-2:123:::PROTID=SLOT-1,PRTYPE=1-1,RVRTV=Y,RVTM=9.0,
CMDMDE=FRCD,CARDMODE=DS1E1-E1ONLY,PEERID=SLOT-2,
REGENNAME="THIS GROUP",PWL=1530.33,RETIME=Y,SHELFROLE=SC,
NEWSHELFID=2:LOCKED,MAINTENANCE;

Input Parameters

<AID>

Access identifier from the "EQPT" section.

<PROTID>

(Optional) Protecting card slot number of the protection group from the "PRSLOT" section.

<PRTYPE>

(Optional) Protection group type. The parameter type is PROTECTION_GROUP, which is the protection group type.

1-1

1:1 protection group

1-N

1:N protection group

<RVRTV>

(Optional) Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<RVTM>

(Optional) Revertive time. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<CMDMDE>

(Optional) Command mode. Only applicable when creating or deleting a protection group (1:1 or 1:N) and/or adding cards to an existing protection group (1:N). Default is NORM. If creating or adding cards to a protection group, specifying FRCD requires the card to be physically plugged in and in the service state (Unlocked). If removing cards from a protection group (1:N) or deleting the protection group (1:1, 1:N), specifying FRCD requires that there are no cross-connects (services) on the card.

The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<CARDMODE>

(Optional) Card mode. TL1 will not set a default CARD_MODE value at the management interface level if no PWL value is given. The parameter type is CARDMODE (card mode). Card mode is applicable to cards that have multiple capabilities, for example, the ML-Series card can operate in two distinct modes: Linear Mapper Mode and L2/L3 Mode.

Note The card will reboot after the mode changes, so the mode change request will not go through if all the ports on the card are not in Locked mode.

AMPL-BST

The optical amplifier is working as an optical booster.

AMPL-PRE

The optical amplifier is working as an optical preamplifier.

DS1E1-DS1ONLY

DS1 mode on DS1E1 card

DS1E1-E1ONLY

E1 mode on DS1E1 card

DWDM-LINE

Line terminating mode

DWDM-SECTION

Section terminating mode

DWDM-TRANS-AIS

Transparent mode AIS

DWDM-TRANS-SQUELCH

Transparent mode SQUELCH

FCMR-DISTEXTN

FC_MR-4 card with distance extension support

FCMR-LINERATE

FC_MR-4 card without distance extension support

ML-GFP

ML-Series card in DOS FPGA using GFP framing type

ML-HDLC

ML-Series card in DOS FPGA using HDLC framing type

ML-IEEE-RPR

ML- Series card in DOS FPGA which supports Resilient Packet Ring (RPR).

MXPMR10DME-4GFC

4-Gbps Fibre Channel/FICON mode for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L card supported on Ports 1and 5.

MXPMR10DME-4GFC-FCGEISC

4-Gbps Fibre Channel/FICON supported on Port 1 and Fibre Channel, GIGE, and ISC modes for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L card supported on Ports 5 to 8.

MXPMR10DME-FCGEISC

Fibre Channel, GIGE, and ISC modes for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L cards supported on all eight ports.

MXPMR10DME-FCGEISC-4GFC

Fibre Channel, GIGE, and ISC modes for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L cards supported on Ports 1 to 4 and 4 Gbps Fibre Channel/FICON supported on Port 5.

MXPMR10G-FCGEISC

Fibre Channel, GIGE and ISC modes for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L card supported on all 8 ports.

MXPMR10G-4GFC

4 Gbps Fibre Channel/FICON mode for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L card supported on Ports 1 and 5.

MXPMR10G-FCGEISC-4GFC

Fibre Channel, GIGE, and ISC modes for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L card supported on Ports 1 to 4 and 4 Gbps Fibre Channel/FICON supported on Port 5.

MXPMR10G-4GFC-FCGEISC

4-Gbps Fibre Channel/FICON supported on Port 1 and Fibre Channel, GIGE, and ISC Modes for the Cisco ONS 15454 SDH MXP_MR_10DME_C and MXP_MR_10DME_L card supported on Ports 5 to 8.

MXPMR25G-ESCON

ESCON mode for the Cisco ONS 15454 SDH MXP_2.5G_10G card.

MXPMR25G-FCGE

Fibre Channel or GIGE mode for the MXP_2.5G_10G card.

MXPMR25G-MIXED

Mixed Fibre Channel, GIGE and ESCON modes for the Cisco ONS 15454 SDH MXP_2.5G_10G card.

<PEERID>

(Optional) The regeneration peer slot from the "EQPT" section.

<REGENNAME>

(Optional) The name of a regeneration group. REGENNAME is a string.

<PWL>

(Optional) Provisioned wavelength. TL1 will not set a default PWL value at the management level if no PWL value is given. The parameter type is OPTICAL_WLEN (optical wavelength).

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<RETIME>

(Optional) Indicates the RETIME function for all the facilities on this card. Applies only to the DS1/E1-56 card. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute

<SHELFROLE>

(Optional) The role of the shelf in the context of the node. When it is omitted it defaults to SC. The parameter is SHELF_ROLE.

NC

The shelf behaves as a node controller.

SC

The shelf behaves as a shelf controller.

<NEWSHELFID>

(Optional) The new shelf identifier is used to change the value of the shelf identifier for the addressed shelf. The value must be different by one and can be in the range from 2 to 8. This field can only be changed if (in the same command) the SHELFROLE is equal to SC. NEWSHELFID is an integer.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.20  ED-FAC

The Edit Facility (ED-FAC) command edits the payload (or signal) type of a facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Ports

Security

Provisioning

Input Format

ED-FAC:[<TID>]:<SRC>:<CTAG>:::[PAYLOAD=<PAYLOAD>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-FAC:CISCO:FAC-3-9:2222:::PAYLOAD=E4-FRAMED,
CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<SRC>

Source access identifier from the "FACILITY" section.

<PAYLOAD>

(Optional) Payload. The parameter type is PAYLOAD, which identifies payload type.

10GFC

10 Gigabit Ethernet Fibre Channel mode

10GIGE

10 Gigabit Ethernet

1GFC

1 Gigabit Fibre Channel mode

1GFICON

1 Gigabit FICON mode

2GFC

2 Gigabit Fibre Channel mode

2GFICON

2 Gigabit FICON mode

DV6000

Video mode

E4-FRAMED

E4-FRAMED payload mode for SDH STM1E-12 card

E4-UNFRAMED

E4-UNFRAMED payload mode for SDH STM1E-12 card

ESCON

ESCON mode

ETRCLO

ETR/CLO payload mode

GIGE

Gigabit Ethernet payload

HDTV

HDTV mode

ISC1

ISC1 Mode

ISC3

ISC3 Mode

STM4

SDH STM4 mode

STM1

SDH STM1 mode

STM16

SDH STM16 mode

PASS-THROUGH

Pass-through mode

SDH

SDH payload mode

SDI-D1-VIDEO

SDI-D1-Video mode

<CMDMDE>

(DS1E1-E1 ONLY) Command mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(DS1E1-E1 only) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(DS1E1-E1 only) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.21  ED-FFP-<MOD2DWDMPAYLOAD>

The Edit Facility Protection Group for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, D1VIDEO, DV6000, ETRCLO, GIGE, HDTV, ISC1, ISC3, or PASSTHRU (ED-FFP-<MOD2DWDMPAYLOAD>) command edits a Y-cable protection group on client facilities.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:];

Input Example

ED-FFP-CLNT:CISCO:FAC-1-1:100:::PROTID=DC-METRO,RVRTV=N,RVTM=1.0,PSDIRN=BI;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<PROTAID>

(Optional) The protection group identifier (protection group name). Defaults to the protecting port AID of the protection group. PROTAID can have a maximum length of 32 characters. PROTAID is a string.

<RVRTV>

(Optional) Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection-switching. Null defaults to N. Only applies to SNCP. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<RVTM>

(Optional) Revertive time. RVTM is not allowed to be set while RVRTV is N. Only applies to SNCP. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<PSDIRN>

(Optional) Protection switch operation. Identifies the switching mode. Defaults to UNI. The parameter type is UNI_BI (unidirectional or bidirectional switch operations).

Note The MXP_2.5G_10G and TXP_MR_10G cards do not support bidirectional switching.

BI

Bidirectional protection switching

UNI

Unidirectional protection switching


11.22  ED-FFP-<STM_TYPE>

The Edit Facility Protection Group for STM1, STM4, STM16, or STM64 (ED-FFP-<STM_TYPE) command edits the optical facility protection. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.


Note This command can be used on both protecting and working AIDs.



Note The VRGRDTM, DTGRDTM, and RCGRDTM parameters are supported in Release 6.0 and later.


Category

Protection

Security

Provisioning

Input Format

ED-FFP-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[PSDIRN=<PSDIRN>],[VRGRDTM=<VRGRDTM>],
[DTGRDTM=<DTGRDTM>],[RCGRDTM=<RCGRDTM>][:];

Input Example

ED-FFP-STM1:PETALUMA:FAC-1-1:1:::PROTID=PROT_NAME,RVRTV=Y,RVTM=1.0,
PSDIRN=BI,VRGRDTM=0.5,DTGRDTM=1.0,RCGRDTM=1.0;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<PROTAID>

(Optional) The protection group identifier (protection group name). PROTAID can have a maximum length of 32 characters. PROTAID is a string.

<RVRTV>

(Optional) Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<RVTM>

(Optional) Revertive time. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<PSDIRN>

(Optional) Protection switch operation. Indicates the switch mode. The parameter type is TRANS_MODE, which is the G1000 transponder mode.

BI

Bidirectional

NONE

Not in transponder mode

UNI

Unidirectional

<VRGRDTM>

(Optional) Verification guard timer. Only applicable to optimized 1+1. The parameter type is VERIFICATION_GUARD_TIMER, which is the optimized 1+1 verification guard timer.

0.5

500 ms

1.0

1 second

<DTGRDTM>

(Optional) Detection guard timer. Only applicable to optimized 1+1. The parameter type is DETECTION _GUARD_TIMER, which is the optimized 1+1 detection guard timer.

0.0

0 seconds

0.05

50 ms

0.1

100 ms

0.5

500 ms

1.0 to 5.0

1 second to 5 seconds

<RCGRDTM>

(Optional) Recovery guard timer. Only applicable to optimized 1+1. The parameter type is RECOVERY_GUARD_TIMER, which is the optimized 1+1 recovery guard timer.

0.0

0 seconds

0.05

50 ms

0.1

100 ms

0.5

500 ms

1.0 to 10.0

1 second to 10 seconds


11.23  ED-FFP-OCH

The Edit Facility Protection Group Optical Channel (ED-FFP-OCH) command changes the provisioning for the default protection group on the DWDM port of a TXP_MR_2.5G or TXPP_MR_2.5G card.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-FFP-OCH:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:];

Input Example

ED-FFP-OCH:VA454-22:CHAN-2-2:100:::PROTID="FIXED PROTECTION",RVRTV=N,
RVTM=1.0,PSDIRN=BI;

Input Parameters

<AID>

Access identifier from the "CHANNEL" sectionl

<PROTAID>

(Optional) The protection group identifier (protection group name). PROTAID is a string.

<RVRTV>

(Optional) Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<RVTM>

(Optional) Revertive time. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<PSDIRN>

(Optional) Protection switch operation. The parameter type is TRANS_MODE, which is the G1000 transponder mode.

BI

Bidirectional

NONE

Not in transponder mode

UNI

Unidirectional


11.24  ED-FSTE

The Edit Fast Ethernet (ED-FSTE) command edits the front end port information of the Fast Ethernet (10/100 Mbps) card.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.


Note For the ML-100T-8 card, only the NAME parameter can be set.


Category

Ports

Security

Provisioning

Input Format

ED-FSTE:[<TID>]:<AID>:<CTAG>:::[FLOW=<FLOW>],[EXPDUPLEX=<EXPDUPLEX>],
[EXPSPEED=<EXPSPEED>],[VLANCOS=<VLANCOS>],[IPTOS=<IPTOS>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];

Input Example

ED-FSTE:CISCO:FAC-1-1:123:::FLOW=Y,EXPDUPLEX=AUTO,EXPSPEED=10_MBPS, VLANCOS=1175,IPTOS=368,NAME="FSTE PORT",CMDMDE=NORM,
SOAK=32:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<FLOW>

(Optional) Flow control. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<EXPDUPLEX>

(Optional) Ethernet duplex mode. The parameter type is ETHER_DUPLEX, which is the duplex mode.

AUTO

Auto mode

FULL

Full mode

HALF

Half mode

<EXPSPEED>

(Optional) Ethernet speed. The parameter type is ETHER_SPEED, which is the Ethernet speed.

100_MBPS

100 Mbps

10_GBPS

10 Gbps

10_MBPS

10 Mbps

1_GBPS

1 Gbps

AUTO

Auto

<VLANCOS>

(Optional) Priority queuing threshold based on VLAN class of service of incoming Ethernet packets. Default value is 1175. VLANCOS is an integer.

<IPTOS>

(Optional) Priority queuing threshold based on IP type of service of incoming Ethernet packets. Default value is 368. IPTOS is an integer.

<NAME>

(Optional) Name. NAME is a string.

<CMDMDE>

(Optional) Command mode. The FRCD mode of operation is applicable to delete a VCAT member cross- connect from Unlocked-Normal or Locked-Autonomous,AutomaticInService service status. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.25  ED-G1000

The Edit G1000 (ED-G1000) command edits the attributes related to a G1000 port.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Ports

Security

Provisioning

Input Format

ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>],[FLOW=<FLOW>],
[LOWMRK=<LOWMRK>],[HIWMRK=<HIWMRK>],[AUTONEG=<AUTONEG>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];

Input Example

ED-G1000:CISCO:FAC-1-1:CTAG:::MFS=1548,FLOW=Y,LOWMRK=20,HIWMRK=492,
AUTONEG=Y,NAME="G1000 PORT",CMDMDE=FRCD,SOAK=32:UNLOCKED,DSBLD;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<MFS>

(Optional) Maximum frame size. The parameter type is MFS_TYPE, which is the maximum frame size used by an Ethernet card.

1548

Normal frame size

JUMBO

Jumbo frame size

<FLOW>

(Optional) Flow control. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<LOWMRK>

(Optional) Low watermark value. LOWMRK is an integer. Defaults to 25.

<HIWMRK>

(Optional) High watermark value. HIWMRK is an integer. Defaults to 485.

<AUTONEG>

(Optional) Automatic negotiation. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<NAME>

(Optional) Name. NAME is a string.

<CMDMDE>

(Optional) Command mode. The FRCD mode of operation is applicable to delete a VCAT member cross- connect from Unlocked-Normal or Locked-Autonomous,AutomaticInService service state. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.26  ED-GFP

The Edit Generic Framing Protocol (ED-GFP) command applies to the FC_MR-4 and CE-1000-4 cards.

Usage Guidelines

On the FC_MR-4 card, the parameters AUTOTHGFPBUF, GFPBUF, and FILTER can be edited only if distance extension is enabled (set to B2B).

Category

Ports

Security

Provisioning

Input Format

ED-GFP:[<TID>]:<AID>:<CTAG>:::[FCS=<FCS>],[AUTOTHGFPBUF=<AUTOTHGFPBUF>],
[GFPBUF=<GFPBUF>],[FILTER=<FILTER>];

Input Example

ED-GFP:CISCO:VFAC-1-0:123:::FCS=N,AUTOTHGFPBUF=Y,GFPBUF=16,FILTER=EGRESS;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<FCS>

(Optional) Payload frame check sequence. The parameter type is FCS (frame check sequence).

FCS-16

Frame check sequencing using 16 bits.

FCS-32

Frame check sequencing using 32 bits.

NONE

No frame check sequence.

<AUTOTHGFPBUF>

(Optional) Autothreshold GFP Buffer. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<GFPBUF>

(Optional) GFP buffer size. GFPBUF is an integer.

<FILTER>

(Optional) Parameter type is GFP_FILTER, which provides the filter feature in GFP.

EGRESS

Active filter feature egress port.

NONE

Turn off filter feature.


11.27  ED-LMP

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Link Management Protocol (ED-LMP) command edits the global LMP protocol attributes.

Usage Guidelines

This command is only available on platforms which support the LMP protocol.

Category

LMP

Security

Provisioning

Input Format

ED-LMP:[<TID>]::<CTAG>:::[ENABLED=<ENABLED>],[WDMEXT=<WDM>], [ROLE=<ROLE>], [LMPNODEID-<NODEID>][:];

Input Example

ED-LMP:PETALUMA::704:::ENABLED=Y,WDMEXT=Y,ROLE=PEER,
LMPNODEID=198.133.219.25;

Input Parameters

<ENABLED>

LMP Protocol Status.

Y

The protocol is enabled.

N

The protocol is disabled.

<WDM>

Determines if the LMP WDM extensions are in effect.

Y

The LMP WDM extensions are in effect.

N

The LMP WDM extensions are not in effect.

<ROLE>

The role the LMP protocol is configured to play.

OLS

The LMP protocol is configured to respond as an Optical Line System.

PEER

The LMP protocol is configured to respond as a peer node.

<NODEID>

LMP Node ID. NODEID is a stable IP address that is always reachable if there is any connectivity to it. The default LMP node ID value is the IP address of the node.


11.28  ED-LMP-CTRL

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Link Management Protocol Control Channel (ED-LMP-CTRL) command edits the LMP control channels.

Usage Guidelines

This command is only available on nodes where the LMP protocol is available and has been enabled.

Category

LMP

Security

Provisioning

Input Format

ED-LMP-CTRL:[<TID>]:<SRC>:<CTAG>:::[LOCALPORT=<LOCALPORT>], [REMOTENE=<REMOTENE>],[REMOTEIP=<REMOTEIP>],[HELLO=<HELLO>],
[HELLOMIN=<HELLOMIN>],[HELLOMAX=<HELLOMAX>],[DEAD=<DEAD>],
[DEADMIN=<DEADMIN>], [DEADMAX=<DEADMAX>]:[<PST>][,<SST>];

Input Example

ED-LMP-CTRL:PETALUMA:CTRL-123:704:::LOCALPORT=FAC-1-1-1,
REMOTENE=15.15.15.115,REMOTEIP=126.0.0.1,HELLO=500,HELLOMIN=300,
HELLOMAX=5000,DEAD=12000,DEADMIN=2000,DEADMAX=20000:OOS,DSBLD;

Input Parameters

<SRC>

The LMP control channel aid values

CTRL-ALL

Specifies all the control channels.

CTRL-{1-4}

Specifies an individual control channel.

<LOCALPORT>

Local port is the pathway that the LMP control channel will use to send and receive messages.

<REMOTENE>

Remote IP address used by the far-end LMP control channel.

<REMOTEIP>

Remote IP address with which the LMP control channel sends and receives messages.

<HELLO>

The time interval in which the LMP protocol sends HELLO messages.

<HELLOMIN>

Minimum hello time the LMP control channels can send out HELLO messages to the remote node.

<HELLOMAX>

The maximum amount of time the LMP control channel can wait between HELLO messages.

<DEAD>

Time interval an LMP control channel will wait for a HELLO message from the remote side before listing the control channel as down.

<DEADMIN>

The minimum amount of time that an LMP control channel can wait before listing the control channel status as down.

<DEADMAX>

The maximum amount of time that the LMP control channel can wait before listing the control channel as down.

<PST>

Primary State. This parameter indicates the current overall service condition of an entity.

IS

In service.

OOS

Out of service.

<SST>

Secondary State. This parameter provides additional information pertaining to PST and PSTQ.

AINS

Automatic in service

DSBLD

Disabled

LPBK

Loopback

MEA

Mismatch of equipment and attributes

MT

Maintenance mode

OOG

Out of group

SWDL

Software downloading

UAS

Unassigned

UEQ

Unequipped


11.29  ED-LMP-TLINK

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Link Management Protocol Traffic Engineering (TE) Link (ED-LMP-TLINK) command edits the LMP TE link.

Usage Guidelines

This command can only be used on nodes that have the LMP protocol available and enabled.

Category

LMP

Security

Provisioning

Input Format

ED-LMP-TLINK:[<TID>]:<SRC>:<CTAG>:::REMOTEID=<REMOTE_ID>, REMOTETE=<REMOTE_TELINK>, [MUXCAP=<MUXCAP>]:[<PST>[,<SST>]];

Input Example

ED-LMP-TLINK:PETALUMA:TLINK-123:704:::REMOTEID=15.15.15.115,REMOTETE=123,
MUXCAP=LAMBDA:OOS,DSBLD;

Input Parameters

<SRC>

LMP TE Link AID Values.

TLINK-ALL

Specifies all the TE links.

TLINK-{1-256}

Specifies an individual TE link.

<REMOTEID>

Remote node ID associated with the LMP TE link.

<REMOTETE>

Remote ID used by the far-end LMP TE Link.

<MUXCAP>

The muxponder capability of the LMP TE link.

PKTSWITCH1

Packet Switching 1.

PKTSWITCH2

Packet Switching 2.

PKTSWITCH3

Packet Switching 3.

PKTSWITCH4

Packet Switching 4.

LAYER2

Layer 2 switching.

TDM

TDM switching.

LAMBDA

Lambda switching.

FIBER

Fiber switching.

<PST>

Primary State. This parameter indicates the current overall service condition of an entity.

IS

In service.

OOS

Out of service.

<SST>

Secondary State. This parameter provides additional information pertaining to PST and PSTQ.

AINS

Automatic in service

DSBLD

Disabled

LPBK

Loopback

MEA

Mismatch of equipment and attributes

MT

Maintenance mode

OOG

Out of group

SWDL

Software downloading

UAS

Unassigned

UEQ

Unequipped


11.30  ED-LMP-DLINK

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Link Management Protocol Data Link (ED-LMP-DLINK) command edits the LMP data link.

Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

ED-LMP-DLINK:[<TID>]:<SRC>:<CTAG>:::[LINKTYPE=<LINKTYPE>],TELINK=<TELINK>,
REMOTEID=<REMOTEID>;

Input Example

ED-LMP-DLINK:PETALUMA:FAC-14-1-1:704:::LINKTYPE=PORT,TELINK=TLNK-45,
REMOTEID=646631;

Input Parameters

<SRC>

Access identifier from the "FACILITY" section.

<LINKTYPE>

The type of LMP data link.

PORT

Port data link.

COMPONENT

Component data link

<TELINK>

Used to map LMP data links to LMP TE links.

<REMOTEID>

The remote LMP data link ID.


11.31  ED-LNK

The Edit Link (ED-LNK) command edits an optical link state.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-LNK:[<TID>]:<FROM>,<TO>:<CTAG>:::[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-LNK:PENNGROVE:BAND-6-1-TX,
BAND-13-1-RX:114:::CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<FROM>

Identifier at one end of the optical link from the "BAND" section.

<TO>

Identifier at the other end of the optical link from the "BAND" section.

<CMDMDE>

(Optional) Command mode. The FRCD mode of operation is applicable to delete a VCAT member cross- connect from Unlocked-Normal or Locked-Autonomous,AutomaticInService service state. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Note PST is not supported for OCH provisioning.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

Note SST is not supported for OCH provisioning.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.32  ED-LNKTERM

The Edit Provisionable Patchcord Termination (ED-LNKTERM) command edits the attributes of a provisionable patchcord that has already been created. Only the remote end attributes (REMOTENODE, REMOTELNKTERMID) can be edited.

Usage Guidelines

No two provisionable patchcord terminations on a node can have the same remote end link termination information. An attempt to modify an existing provisionable patchcord termination while not following the above restriction will return an error message.

If the provisionable patchcord termination does not exist, an error message will be returned.

This command does not accept multiple and ALL AIDs.

REMOTENODE is a string with a maximum length of 20 characters.

Category

Provisionable Patchcords

Security

Provisioning

Input Format

ED-LNKTERM:[<TID>]:<AID>:<CTAG>:::[REMOTENODE=<REMOTENODE>],
[REMOTELNKTERMID=<REMOTELNKTERMID>];

Input Example

ED-LNKTERM::LNKTERM-1:CTAG:::REMOTENODE=172.20.208.226,
REMOTELNKTERMID=25;

Input Parameters

<AID>

Access identifier from the "LNKTERM" section. Indicates a link (provisionable patchcord) termination on the local node.

<REMOTENODE>

(Optional) The node where the other end of the provisionable patchcord resides. This can be an IP address or a valid TID. Defaults to the IP address of the local node/existing value. REMOTENODE is a string.

<REMOTELNKTERMID>

(Optional) The corresponding provisionable patchcord termination on the remote node (as specified by the REMOTENODE parameter). Integer value within the range of 1 to 65535. Defaults to existing value.


11.33  ED-NE-GEN

The Edit Network Element General (ED-NE-GEN) command edits the node attributes of the NE.

Usage Guidelines

The node name can be a maximum of 20 characters. If the entered name exceeds 20 characters, an Node Name Too Long (IPNV) error message is returned.

An existing NTP timing source can be removed by setting the address to 0.0.0.0.

The maximum length of IPADDR and DEFRTR is 20 characters. The default value is the local IP address and default router.

The maximum length of IPMASK is 18 characters. The default value is the mask of local IP address.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.


Caution Changing the IPADDR, IPMASK, or IIOP Port will cause a reset of the TCC2/TCC2P.

Category

System

Security

Superuser

Input Format

ED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>],[IPADDR=<IPADDR>],
[IPMASK=<IPMASK>],[DEFRTR=<DEFRTR>],[IIOPPORT=<IIOPPORT>],
[NTP=<NTP>],[SUPPRESSIP=<SUPPRESSIP>],[MODE=<MODE>];

Input Example

ED-NE-GEN:CISCO::123:::NAME=NODENAME,IPADDR=192.168.100.52,
IPMASK=255.255.255.0,DEFRTR=192.168.100.1,IIOPPORT=57790,
NTP=192.168.100.52,SUPPRESSIP=NO,MODE=SINGLESHELF;

Input Parameters

<NAME>

(Optional) Node name. NAME is a string. Defaults to Null.

<IPADDR>

(Optional) Node IP address. IPADDR is a string.

<IPMASK>

(Optional) Node IP mask. IPMASK is a string.

<DEFRTR>

(Optional) Node default router. DEFRTR is a string.

<IIOPPORT>

(Optional) Node IIOP port. IIOPPORT is an integer. Defaults to 57790.

<NTP>

(Optional) Node Network Time Protocol (NTP) timing origin address. NTP is a string. Defaults to 0.0.0.0.

<SUPPRESSIP>

(Optional) The parameter type is YES_NO, which signifies whether the user's password is about to expire, the user is logged into the NE, or the user is locked out of the NE.

NO

No

YES

Yes

<MODE>

(Optional) Indicates the AID mode to access shelf identifier objects. Defaults to SINGLESHELF. This field is always set to MULTISHELF for DWDM nodes with more than one shelf managed. The parameter type is SHELF_MODE, which is the NE mode.

SINGLESHELF

The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.

MULTISHELF

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.

MULTISHELFETH

The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.


11.34  ED-NE-PATH

The Edit Network Element Path (ED-NE-PATH) command edits the path attributes of the NE.

Usage Guidelines

The default values for optional parameters are NE default values.

Category

System

Security

Provisioning

Input Format

ED-NE-PATH:[<TID>]::<CTAG>:::[PDIP=<PDIP>],[XCMODE=<XCMODE>];

Input Example

ED-NE-PATH:::CTAG:::PDIP=Y,XCMODE=MIXED;

Input Parameters

<PDIP>

(Optional) Flag used to indicate whether PDI-P should be generated on the outgoing VT structured VCs. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<XCMODE>

(Optional) Cross-connect mode. The parameter type is XCMODE, which is applicable only to a node with cross-connect cards (XC-VXL-10G, XC-VXL-2.5G, or XC-VXC-10G) that support cross-connect mode change.

MIXED

Both VC11 and VC12 cross-connects can be provisioned on the node.

VC11

Only VC11 cross-connects can be provisioned on the node.

VC12

Only VC12 cross-connects can be provisioned on the node.


11.35  ED-NE-SYNCN

The Edit Network Element Synchronization (ED-NE-SYNCN) command edits the synchronization attributes of the NE.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Although mixed-mode timing is supported in this release, it is not recommended. Refer to the Cisco ONS SONET TL1 Reference Guide for more information.

The ONS 15454 SDH mode functionality is:

External mode: The node derives its timing from the BITS inputs.

Line mode: The node derives its timing from the SDH line(s).

Mixed mode: The node derives its timing from the BITS input or SDH lines.

Category

Synchronization

Security

Provisioning

Input Format

ED-NE-SYNCN:[<TID>]:[<AID>]:<CTAG>:::[TMMD=<TMMD>],[SSMGEN=<SSMGEN>],
[QRES=<QRES>],[RVRTV=<RVRTV>],[RVTM=<RVTM>];

Input Example

ED-NE-SYNCN:CISCO::123:::TMMD=LINE,SSMGEN=GEN1,QRES=ABOVE-STU_SDH,
RVRTV=Y,RVTM=8.0;

Input Parameters

<AID>

The node or shelf access identifier from the "SHELF" section. If omitted, it addresses the node or first shelf of the node. Must not be null.

<TMMD>

(Optional) Timing mode. Defaults to EXTERNAL. The parameter type is TIMING_MODE, which is the timing mode for the current node.

EXTERNAL

The node derives its clock from the BITS input.

LINE

The node derives it's clock from the SDH lines.

MIXED

The node derives it's clock from the mixed timing mode.

<SSMGEN>

(Optional) Synchronization status message (SSM) set. Defaults to GEN1. The parameter type is SYNC_GENERATION, which is the generation of the synchronization status message set.

GEN1

First generation SSM set

GEN2

Second generation SSM set

<QRES>

(Optional) Quality of the RES. Defaults to DUS. The parameter type is SYNC_QUALITY_LEVEL, which is the network synchronization quality level.

ABOVE-G811

Better than G811

ABOVE-STU_SDH

Between STU_SDH and G811 (default setting)

ABOVE-G812T

Between G812T and STU_SDH

ABOVE-G812L

Between G812L and G812T

ABOVE-SETS

Between SETS and G812L

BELOW-SETS

Below SETS but still usable

SAME-AS-DUS_SDH

Disable the RES message by equating to DUS_SDH

<RVRTV>

(Optional) Revertive mode. The value Y indicates that the protection-switching system reverts service to the original line after restoration. The value N indicates that the protection-switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. A null value is equivalent to ALL. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<RVTM>

(Optional) Revertive time. A null value is equivalent to ALL. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.


11.36  ED-OCH

The Edit Optical Channel (ED-OCH) command edits the attributes (service parameters) and state of an OCH facility.

Usage Guidelines

Refer to the Cisco ONS SONET TL1 Reference Guide for specific card provisioning rules.


Note Primary=Locked and secondary=AutomaticInService status do not apply to Ethernet mode.


The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[EXPWLEN=<EXPWLEN>],
[VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>],[CALOPWR=<CALOPWR>],
[CHPOWER=<CHPOWER>],[NAME=<PORTNAME>],[SFBER=<SFBER>],[SDBER=<SDBER>],
[COMM=<COMM>],[GCCRATE=<GCCRATE>],[OSDBER=<OSDBER>],[DWRAP=<DWRAP>],
[FEC=<FEC>],[PAYLOADMAP=<PAYLOADMAP>],[MACADDR=<MACADDR>],
[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[SOAK=<SOAK>],[OSPF=<OSPF>],
[MFS=<MFS>][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-OCH:CISCO:CHAN-6-2:114:::RDIRN=W-E,EXPWLEN=1530.32,VOAATTN=2.5,
VOAPWR=7.5,CALOPWR=0,CHPOWER=2.0,NAME="NYLINE",SFBER=1E-5,SDBER=1E-6,
COMM=DCC,GCCRATE=192K,OSDBER=1E-6,DWRAP=Y,FEC=STD,PAYLOADMAP=ASYNCH,MACADDR=00-0E-AA-BB-CC-DD,SYNCMSG=N,SENDDUS=Y,SOAK=10,OSPF=Y,MFS=2152,
CMDMDE=NORM:LOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "CHANNEL" section.

<RDIRN>

(Optional) Ring directionality of the optical line. The parameter type is RDIRN_MODE, which is the optical ring directionality.

E-W

The direction of the signal is from east to west (clockwise).

W-E

The direction of the signal is from west to east (counterclockwise).

<EXPWLEN>

(Optional) Optical wavelength for this port. Applicable only to the following types of cards: optical service channel cards, optical amplifier cards, dispersion compensation units, multiplexer and demultiplexer cards, and optical add/drop multiplexing (OADM) cards. The parameter type is OPTICAL_WLEN, which is the optical wavelength.

1310

Wavelength 1310

1470

Wavelength 1470

1490

Wavelength 1490

1510

Wavelength 1510

1529.55

Wavelength 1529.55

1529.94

Wavelength 1529.94

1530

Wavelength 1530

1530.33

Wavelength 1530.33

1530.73

Wavelength 1530.73

1531.12

Wavelength 1531.12

1531.51

Wavelength 1531.51

1531.90

Wavelength 1531.90

1532.29

Wavelength 1532.29

1532.68

Wavelength 1532.68

1533.07

Wavelength 1533.07

1533.47

Wavelength 1533.47

1533.86

Wavelength 1533.86

1534.25

Wavelength 1534.25

1534.64

Wavelength 1534.64

1535.04

Wavelength 1535.04

1535.43

Wavelength 1535.43

1535.82

Wavelength 1535.82

1536.22

Wavelength 1536.22

1536.61

Wavelength 1536.61

1537

Wavelength 1537

1537.40

Wavelength 1537.40

1537.79

Wavelength 1537.79

1538.19

Wavelength 1538.19

1538.58

Wavelength 1538.58

1538.98

Wavelength 1538.98

1539.37

Wavelength 1539.37

1539.77

Wavelength 1539.77

1540.16

Wavelength 1540.16

1540.56

Wavelength 1540.56

1540.95

Wavelength 1540.95

1541.35

Wavelength 1541.35

1541.75

Wavelength 1541.75

1542.14

Wavelength 1542.14

1542.35

Wavelength 1542.35

1542.54

Wavelength 1542.54

1542.94

Wavelength 1542.94

1543.33

Wavelength 1543.33

1543.73

Wavelength 1543.73

1544.13

Wavelength 1544.13

1544.53

Wavelength 1544.53

1544.92

Wavelength 1544.92

1545.32

Wavelength 1545.32

1545.72

Wavelength 1545.72

1546.12

Wavelength 1546.12

1546.52

Wavelength 1546.52

1546.92

Wavelength 1546.92

1547.32

Wavelength 1547.32

1547.72

Wavelength 1547.72

1548.12

Wavelength 1548.12

1548.51

Wavelength 1548.51

1548.92

Wavelength 1548.92

1549.32

Wavelength 1549.32

1549.71

Wavelength 1549.71

1550

Wavelength 1500

1550.12

Wavelength 1550.12

1550.52

Wavelength 1550.52

1550.92

Wavelength 1550.92

1551.32

Wavelength 1551.32

1551.72

Wavelength 1551.72

1552.12

Wavelength 1552.12

1552.52

Wavelength 1552.52

1552.93

Wavelength 1552.93

1553.33

Wavelength 1553.33

1553.73

Wavelength 1553.73

1554.13

Wavelength 1554.13

1554.13

Wavelength 1554.13

1554.94

Wavelength 1554.94

1555.34

Wavelength 1555.34

1555.75

Wavelength 1555.75

1556.15

Wavelength 1556.15

1556.55

Wavelength 1556.55

1556.96

Wavelength 1556.96

1557.36

Wavelength 1557.36

1557.77

Wavelength 1557.77

1558.17

Wavelength 1558.17

1558.58

Wavelength 1558.58

1558.98

Wavelength 1558.98

1559.39

Wavelength 1559.39

1559.79

Wavelength 1559.79

1560.20

Wavelength 1560.20

1560.61

Wavelength 1560.61

1561.01

Wavelength 1561.01

1561.42

Wavelength 1561.42

1561.83

Wavelength 1561.83

1570

Wavelength 1570

1570.83

Wavelength 1570.83

1571.24

Wavelength 1571.24

1571.65

Wavelength 1571.65

1572.06

Wavelength 1572.06

1572.48

Wavelength 1572.48

1572.89

Wavelength 1572.89

1573.30

Wavelength 1573.30

1573.71

Wavelength 1573.71

1574.13

Wavelength 1574.13

1574.54

Wavelength 1574.54

1574.95

Wavelength 1574.95

1575.37

Wavelength 1575.37

1575.78

Wavelength 1575.78

1576.20

Wavelength 1576.20

1576.61

Wavelength 1576.61

1577.03

Wavelength 1577.03

1577.44

Wavelength 1577.44

1577.86

Wavelength 1577.86

1578.27

Wavelength 1578.27

1578.69

Wavelength 1578.69

1579.10

Wavelength 1579.10

1579.52

Wavelength 1579.52

1579.93

Wavelength 1579.93

1580.35

Wavelength 1580.35

1580.77

Wavelength 1580.77

1581.18

Wavelength 1581.18

1581.60

Wavelength 1581.60

1582.02

Wavelength 1582.02

1582.44

Wavelength 1582.44

1582.85

Wavelength 1582.85

1583.27

Wavelength 1583.27

1583.69

Wavelength 1583.69

1584.11

Wavelength 1584.11

1584.53

Wavelength 1584.53

1584.95

Wavelength 1584.95

1585.36

Wavelength 1585.36

1585.78

Wavelength 1585.78

1586.20

Wavelength 1586.20

1586.62

Wavelength 1586.62

1587.04

Wavelength 1587.04

1587.46

Wavelength 1587.46

1587.88

Wavelength 1587.88

1588.30

Wavelength 1588.30

1588.73

Wavelength 1588.73

1589.15

Wavelength 1589.15

1589.57

Wavelength 1589.57

1589.99

Wavelength 1589.99

1590

Wavelength 1590

1590.41

Wavelength 1590.41

1590.83

Wavelength 1590.83

1591.26

Wavelength 1591.26

1591.68

Wavelength 1591.68

1592.10

Wavelength 1592.10

1592.52

Wavelength 1592.52

1592.95

Wavelength 1592.95

1593.37

Wavelength 1593.37

1593.79

Wavelength 1593.79

1594.22

Wavelength 1594.22

1594.64

Wavelength 1594.64

1595.06

Wavelength 1595.06

1595.49

Wavelength 1595.49

1596.34

Wavelength 1596.34

1596.76

Wavelength 1596.76

1597.19

Wavelength 1597.19

1597.62

Wavelength 1597.62

1598.04

Wavelength 1598.04

1598.47

Wavelength 1598.47

1598.89

Wavelength 1598.89

1599.32

Wavelength 1599.32

1599.75

Wavelength 1599.75

1600.06

Wavelength 1600.06

1601.03

Wavelength 1601.03

1601.46

Wavelength 1601.46

1601.88

Wavelength 1601.88

1602.31

Wavelength 1602.31

1602.74

Wavelength 1602.74

1603.17

Wavelength 1603.17

1603.60

Wavelength 1603.60

1604.03

Wavelength 1604.03

1610

Wavelength 1610

USE-TWL1

Use Tunable Wavelength 1

<VOAATTN>

(Optional) The value of calibrated attenuation for the variable optical attenuator (VOA). It is expressed in dBm. The range is 0.0 to +30.0 for the following types of cards: optical service channel, optical amplifier, dispersion compensation units, multipelxer and demultipelxer, and OADM. Not supported for TXP or MXP cards. VOAATTN is a float.

<VOAPWR>

(Optional) The value of calibrated output power that the VOA is going to set as a result of its attenuation. Applicable only to the following types of cards: optical service channel, optical amplifier, dispersion compensation units, multipelxer and demultipelxer, and OADM. VOAPWR is a float.

<CALOPWR>

(Optional) The value of the calibrated optical power expected for the line added to the calculated value, which equals the total expected output power. Expressed in dBm. Applicable only to the following types of cards: optical service channel, optical amplifier, dispersion compensation units, multipelxer and demultipelxer, and OADM. Defaults to 0 dBm. CALOPWR is a float.

<CHPOWER>

(Optional) The value of per-channel optical power expected by the OCH drop port of an AD-4C-xx.x unit. CHPOWER is a float expressed in dBm. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<PORTNAME>

(Optional) Port name. PORTNAME is a string.

<SFBER>

(Optional) Signal failure threshold for the SDH payload. Can only be provisioned on the working port. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

(Optional) Signal degrade threshold for the SDH payload. Can only be provisioned on the working port. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<COMM>

(Optional) The GCC or DCC is enabled or disabled. The GCC can be enabled only if the digital wrapper has been enabled for the card. The default is NONE. For an MXP_2.5G_10G or TXP_MR_10G client port, only the DCC can be provisioned if the termination mode is not transparent and the payload is SDH. On an MXP_2.5G_10G or TXP_MR_10G DWDM port, the DCC can be enabled only if ITU-T G.709 monitoring is not enabled and if the payload is SDH and the termination mode is not transparent. On an MXP_2.5G_10G or TXP_MR_10G DWDM port, the GCC can be enabled if there is no DCC and the ITU-T G.709 monitoring flag is enabled. On a TXP or MXP DWDM port, the DCC/GCC can be disabled only if there are no provisionable patchcord terminations provisioned on the trunk port. The parameter type is COMM_TYPE, which is the out-of-band communications channel termination type.

DCC

RS-DCC type

GCC

Generic communication channel (OTN) type

NONE

Disable DCC or GCC if enabled

<GCCRATE>

(Optional) The data rate of the GCC traffic. The default is 192 Kbps. For MXP_2.5G_10G and TXP_MR_10G cards, this applies only to the DWDM port. The parameter type is GCCRATE, which is the data rate of the GCC traffic.

192K

192 Kbps

576K

576 Kbps

<DWRAP>

(Optional) The ITU-T G.709 monitoring digital wrapper. It is either on or off. The system default is ON. For MXP_2.5G_10G and TXP_MR_10G cards, this applies only to the DWDM port. The parameter type is ON_OFF (disable or enable an attribute).

To enable ITU-T G.709 monitoring, there should be no GCC on the DWDM port and the payload (in which the card is configured) should not be UNFRAMED.

To disable ITU-T G.709 monitoring, there should be no GCC on the DWDM port, the FEC should be turned to off, there should be no overhead circuit created on the DWDM port, and none of the client ports on the card should be part of a Y-cable protection group (muxponder only).

N

Disable an attribute.

Y

Enable an attribute.

<FEC>

(Optional) Forward error correction. It can be enabled only if ITU-T G.709 monitoring is turned ON. It is either off or enabled in standard or enhanced mode. The system default is standard FEC enabled. The FEC level PM and thresholds apply if the FEC is turned ON. The parameter type is FEC_MODE, which specifies the type of forward error correction.

ENH

Enhanced FEC is enabled.

OFF

FEC is disabled.

STD

Standard FEC is enabled.

<PAYLOADMAP>

(Optional) The type of payload mapping. It can be enabled only if ITU-T G.709 monitoring is turned ON and FEC is enabled. The parameter type is PAYLOAD_MAPPING, which is the payload mapping mode.

ASYNCH

Asynchronous mapping mode

ODU

ODU multiplex structure mode

SYNCH

Synchronous mapping mode

<MACADDR>

(Optional) MAC address for the 10GigE payload. MACADDR is a string.

<SYNCMSG>

(Optional) The facility can be enabled to provide the synchronization clock. The parameter type is ON_OFF (disable or enable an attribute). This does not apply to the TXP_MR_10G card. This applies to an MXP_2.5G_10G card only if the payload is SONET/SDH and the card termination mode is as follows:

TRANSPARENT: All client ports are available for all timing selections. All trunk ports are not available.

LINE: All ports are available for all timing selections.

N

Disable an attribute.

Y

Enable an attribute.

<SENDDUS>

(Optional) The facility sends out a Do not Use for Synchronization message. The parameter type is ON_OFF (disable or enable an attribute). This does not apply to the TXP_MR_10G card. This applies to an MXP_2.5G_10G card only if the payload is SONET/SDH and the card termination mode is as follows:

TRANSPARENT: All client ports are available for all timing selections. All trunk ports are not available.

LINE: All ports are available for all timing selections.

N

Disable an attribute.

Y

Enable an attribute.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<OSPF>

(Optional) Open Shortest Path First. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.

N

The ring does not support the extended K1/K2/K3 protocol

Y

The ring does support the extended K1/K2/K3 protocol

<MSF>

(Optional) Indicates the maximum frame size used by an Ethernet card. MSF is an integer.

<CMDMDE>

(Optional) Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.37  ED-OCHCC

The Edit Optical Channel Client Connection (ED-OCHCC) command edits the OCH client connection.

Usage Guidelines

The fields after CTAG (trailing colons) are optional.

This command does not support multiple editing of OCH client connection provisioning.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-OCHCC:VA454-22:FAC-2-1-1:116:::CKTID=OCHCC,CMDMDE=FRCD:LOCKED,DISABLED;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<CKTID>

(Optional) Circuit identification that contains the common language Circuit ID or other alias of the circuit being provisioned. Cannot contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<CMDMDE>

(Optional) The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that may make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.38  ED-OCHNC

The Edit Optical Channel Network Connection (ED-OCHNC) command edits the OCH network connection.

Usage Guidelines

The fields after CTAG (trailing colons) are optional.

This command does not support multiple editing of wavelength connection provisioning.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-OCHNC:VA454-22:CHANWL-1-3-TX-1530.33,
LINEWL-4-1-RX-1530.33:116:::CKTID=CIRCUIT,CMDMDE=FRCD:LOCKED,DISABLED;

Input Parameters

<SRC>

Source access identifier from the "CHANNEL" section. In two-way wavelength connection sources, both directions need to be indicated.

<DST>

Destination access identifier from the "LINEWL" section. In two-way wavelength connection sources, both directions need to be indicated.

<CKTID>

(Optional) Circuit identification that contains the common language Circuit ID or other alias of the circuit being provisioned. Cannot contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<CMDMDE>

(Optional) The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that may make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.39  ED-OMS

The Edit Optical Multiplex Section (ED-OMS) command edits the attributes (service parameters) and state of an OMS facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-OMS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[EXPBAND=<EXPBAND>],
[VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>],[CALOPWR=<CALOPWR>],
[CHPOWER=<CHPOWER>],[NAME=<NAME>],[SOAK=<SOAK>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-OMS:PENNGROVE:BAND-6-1:114:::RDIRN=W-E,EXPBAND=1530.32-1532.68,
VOAATTN=2.5,VOAPWR=7.5,CALOPWR=0.0,CHPOWER=2.0,NAME="OMSPORT",
SOAK=8,CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "BAND" section.

<RDIRN>

(Optional) Ring directionality of the optical line. The parameter type is RDIRN_MODE, which is the optical ring directionality.

E-W

The direction of the signal is from east to west (clockwise).

W-E

The direction of the signal is from west to east (counterclockwise).

<EXPBAND>

(Optional) The expected value of band for this port. The parameter type is OPTICAL_BAND (optical band).

1530.33 to 1532.68

Band 1

1534.25 to 1536.61

Band 2

1538.19 to 1540.56

Band 3

1542.14 to 1544.53

Band 4

1546.12 to 1548.51

Band 5

1550.12 to 1552.52

Band 6

1554.13 to 1556.55

Band 7

1558.17 to 1560.61

Band 8

USE-DEFAULT

This band has not yet been configured or retrieved from unit.

<VOAATTN>

(Optional) The value of calibrated attenuation for the VOA expressed in dBm. The range is 0.0 to +30.0. VOAATTN is a float.

<VOAPWR>

(Optional) The value of calibrated output power that the VOA is going to set as a result of its attenuation. VOAPWR is a float.

<CALOPWR>

(Optional) The value of the calibrated optical power expected for the line added to the calculated value, which equals the total expected output power. Expressed in dBm. Defaults to 0 dBm. CALOPWR is a float.

<CHPOWER>

(Optional) The value of per-channel optical power. Float expressed in dBm. The parameter type is REVERTIVE_TIME (revertive time).

0.5 to 12.0

Revertive time is 0.5 to 12.0 minutes.

<NAME>

(Optional) Port name. NAME is a string.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32. SOAK is an integer.

<CMDMDE>

(Optional) Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.40  ED-OSC

The Edit Optical Service Channel (ED-OSC) command edits the OSC group attributes.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

ED-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>];

Input Example

ED-OSC:PENNGROVE:OSC-1:114:::RINGID=1,NODEID=10;

Input Parameters

<AID>

Access identifier from the "OSC" section.

<RINGID>

(Optional) The OSC ring ID of the NE up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.

<NODEID>

(Optional) The OSC node ID of the NE. NODEID ranges from 0 to 31. NODEID is an integer.


11.41  ED-OTS

The Edit Optical Transport Section (ED-OTS) command edits the attributes (service parameters) and state of an OTS facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-OTS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[VOAATTN=<VOAATTN>],
[VOAPWR=<VOAPWR>],[OFFSET=<OFFSET>],[CALTILT=<CALTILT>],[OSRI=<OSRI>],
[AMPLMODE=<AMPLMODE>],[CHPOWER=<CHPOWER>],[EXPGAIN=<EXPGAIN>],
[NAME=<NAME>],[SOAK=<SOAK>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-OTS:PENNGROVE:LINE-6-1:114:::RDIRN=W-E,VOAATTN=5.0,VOAPWR=10.0,OFFSET=0.0,CALTILT=0.0,OSRI=N,AMPLMODE=GAIN,CHPOWER=10.0,EXPGAIN=-5.0,
NAME="OTS PORT",SOAK=8,CMDMDE=NORM:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "LINE" section.

<RDIRN>

(Optional) Ring directionality of the optical line. The parameter type is RDIRN_MODE, which is the optical ring directionality.

E-W

The direction of the signal is from east to west (clockwise).

W-E

The direction of the signal is from west to east (counterclockwise).

<VOAATTN>

(Optional) The value of calibrated attenuation for the VOA expressed in dBm. The range is 0.0 to +30.0. VOAATTN is a float.

<VOAPWR>

(Optional) The value of calibrated output power that the VOA is going to set as a result of its attenuation. VOAPWR is a float.

<OFFSET>

(Optional) The calibration value of the optical power added to the calculated reference value. Defaults to 0 dBm. OFFSET is a float.

<CALTILT>

(Optional) The amplifier calibration tilt offset to be added to the calculated reference value. Defaults to 0 dBm. CALTILT is a float.

<OSRI>

(Optional) OSRI enabled or disabled. Present only on a port where the safety is supported. The parameter type is ON_OFF (disable or enable an attribute)

N

Disable an attribute.

Y

Enable an attribute.

<AMPLMODE>

(Optional) The optical amplification control mode. The parameter type is AMPL_MODE, which defines the amplifier control mode.

GAIN

The amplifier always maintains a fixed gain.

POWER

The amplifier maintains the output power to a fixed value.

<CHPOWER>

(Optional) The per-channel optical power. CHPOWER is a float.

<EXPGAIN>

(Optional) The gain expected value to be reached from an amplifier when the node is part of a DWDM access network. EXPGAIN is a float.

<NAME>

(Optional) The name of the port. NAME is a string.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32. SOAK is an integer.

<CMDMDE>

(Optional) Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

(Optional) Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


.

11.42  ED-PID

The Edit Password (ED-PID) command allows a user to change his or her own password.

Usage Guidelines

The password cannot be null.

Passwords are masked for the following security commands: ACT-USER, ED-PID, ENT-USER-SECU and ED-USER-SECU. Access to a TL1 session by any means will have the password masked. The CTC Request History and Message Log will also show the masked commands. When a password-masked command is reissued by double-clicking the command from CTC Request History, the password will still be masked in the CTC Request History and Message Log. The actual password that was previously issued will be sent to the NE. To use a former command as a template only, single-click the command in CTC Request History. The command will be placed in the Command Request text box, where you can edit the appropriate fields prior to reissuing it.

The password will not appear in the TL1 log on the NE.

For the ED-PID command:

ED-PID:[TID]:<UID>:[CTAG]::<OLDPID>,<NEWPID>;

the syntax of OLDPID is not checked. The NEWPID is required to follow Telcordia standards (for example, 10 characters maximum including 1 letter, 1 number, and any one of the following characters: #, %, or +). The OLDPID must match what is in the database.

You must use the ED-USER-SECU command to change the default password (empty) for the CISCO15 Superuser.

The ED-PID command cannot be used to change the empty password to a valid password.

Category

Security

Security

Retrieve

Input Format

ED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>;

Input Example

ED-PID:CISCO:UID:123::OLDPWD,NEWPWD;

Input Parameters

<UID>

User identifier. Up to 10 alphanumeric characters. UID is a string.

<OLDPID>

The user's old password. Up to 10 alphanumeric characters. Passwords are encrypted and will appear as asterisks (*). OLDPID is a string.

<NEWPID>

The user's new password. Up to 10 alphanumeric characters. Passwords are encrypted and will appear as asterisks (*). NEWPID is a string.


11.43  ED-POS

The Edit Packet Over SDH (ED-POS) command edits the back-end port information for the Ethernet card when the back-end port is working in packet-over-SDH (POS) mode.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command to retrieve them. ED-POS cannot set ENCAP and PST/SST.


Note This command is supported on the ONS 15454 SDH CE-100T-8 and CE-1000-4 cards.


Category

Ports

Security

Provisioning

Input Format

ED-POS:[<TID>]:<AID>:<CTAG>:::[ENCAP=<ENCAP>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];

Input Example

ED-POS:CISCO:VFAC-2-0:123:::ENCAP=HDLC,NAME=NAME,CMDMDE=NORM,
SOAK=32:UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<ENCAP>

(Optional) Encapsulation. Defaults to HDLC. The parameter type is ENCAP, which is the frame encapsulation type.

GFP_F

GFP frame mode

GFP_T

GFP transparent mode

HDLC

HDLC frame mode

HDLC_LEX

HDLC LAN extension frame mode

HDLC_X86

HDLC X.86 frame mode

<NAME>

(Optional) NAME is a string. Defaults to NULL. Maximum length is 32 characters.

<CMDMDE>

(Optional) Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<SOAK>

(Optional) Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.

<PST>

(Optional) Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

(Optional) Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.44  ED-PROTOCOL

The Edit Protocol (ED-PROTOCOL) command is used to enable/disable a protocol/service that is supported in the NE. Valid protocols include shell/file system access (SHELL), element management system (EMS), TL1, and SNMP.

Usage Guidelines

If the PROTOCOLAID is TL1, the command will be denied because TL1 users are not allowed to change the setting for TL1 protocol.

If the POTOCOLAID is SNMP, the SECURE PROTOCOLSTAT is not supported. SNMP can only be enabled or disabled. To enable SNMP, set PROTOCOLSTAT to UNSECURE.

Category

Security

Security

Superuser

Input Format

ED-PROTOCOL:[<TID>]:<PROTOCOLAID>:<CTAG>::<PROTOCOLSTAT>;

Input Example

ED-PROTOCOL:CISCONODE:EMS:123::SECURE;

Input Parameters

<PROTOCOLAID>

The protocol/service to which the command pertains. The parameter type is PROTOCOLAID, which is the AID for protocol/service.

EMS

CTC/CTM protocol/service

SHELL

Shell/file system access protocol

SNMP

SNMP protocol/service

TL1

TL1 protocol service

<PROTOCOLSTAT>

Identifies the status of the protocol/service. The parameter type is PROTOCOLSTAT, which is the status of the protocol.

DISABLED

The protocol cannot be used.

SECURE

The protocol is enabled and communications using the protocol are sure, for example, through SSH. Not applicable for SNMP protocols.

UNSECURE

The protocol is enabled but communication is not secure, for example, through Telnet.


11.45  ED-ROLL-<MOD_PATH>

The Edit Roll for VC3, VC44C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC11, or VC12 (ED-ROLL-<MOS_PATH>) command forces a rolling operation. Force attempts to force a valid signal to complete the rolling operation.

Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

ED-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::[CMDMDE=<CMDMDE>];

Input Example

ED-ROLL-VC4:CISCO:VC4-1-1-1,VC4-2-1-1:1:::CMDMDE=FRCD;

Input Parameters

<FROM>

Source access identifier from the "VC" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the FROM-AID termination point. Otherwise, FROM is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue the RTRV-CRS command, and use the response for FROM and TO parameters.

<TO>

Destination access identifier from the "VC" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the TO-AID termination point. Otherwise, the TO is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue the RTRV-CRS command, and use the response for FROM and TO parameters.

<CMDMDE>

(Optional) Command execution mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands, but you can specify FRCD to force the system to override a state in which the command would normally be denied.

Note CMDMDE can only go from NORM to FRCD. (It cannot go from FRCD to NORM.)

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.


11.46  ED-SLV-WDMANS

The Edit Span Loss Verification Wavelength Division Multiplexing Automatic Node Set Up (ED-SLV-WDMANS) command edits the expected span loss verification.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

ED-SLV-WDMANS:[<TID>]:<AID>:<CTAG>:::[HIGHSLVEXP=<HIGHSLVEXP>],
[LOWSLVEXP=<LOWSLVEXP>];

Input Example

ED-SLV-WDMANS:VA454-22:WDMANS-E:116:::HIGHSLVEXP=10.0,LOWSLVEXP=5.0;

Input Parameters

<AID>

Access identifier from the "WDMANS" section.

<HIGHSLVEXP>

(Optional) The high range value of the expected span loss verification. HIGHSLVEXP is a float.

<LOWSLVEXP>

(Optional) The low range value of the expected span loss verification. LOWSLVEXP is a float.


11.47  ED-STM1E

The Edit STM1E (ED-STM1E) command edits the attributes and the state of the STM1E port facility.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Ports

Security

Provisioning

Input Format

ED-STM1E:[<TID>]:<SRC>:<CTAG>:::[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],
[PJMON=<PJMON>],[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-STM1E:CISCO1:FAC-6-1:114:::SYNCMSG=Y,SENDDUS=N,PJMON=48,SFBER=1E-4,
SDBER=1E-6,SOAK=10,NAME="STM1EPORT",CMDMDE=NORM:UNLOCKED,
AUTOMATICINSERVICE;

Input Parameters

<SRC>

Source access identifier from the "FACILITY" section.

<SYNCMSG>

Indicates if Synchronization messaging is enabled or disabled on the facility. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<SENDDUS>

The facility sends out a Do not Use (DUS) for Synchronization message. Defaults to N. The parameter type is ON_OFF (disable or enable an attribute).

N

Disable an attribute.

Y

Enable an attribute.

<PJMON>

(Optional) Identifies an STM port PJMON. PJMON is an integer. It defaults to 0 (zero). Set a valid VC4 number of the optical port.

Note The PJMON number displayed in TL1 interface does not correspond to the PJVC4MON number in CTC, but instead corresponds to the VC4 number of the optical port.

<SFBER>

The port signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.

1E-3

SFBER is 1E-3.

1E-4

SFBER is 1E-4.

1E-5

SFBER is 1E-5.

<SDBER>

Port signal degrade threshold. Defaults on 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.

1E-5

SDBER is 1E-5.

1E-6

SDBER is 1E-6.

1E-7

SDBER is 1E-7.

1E-8

SDBER is 1E-8.

1E-9

SDBER is 1E-9.

<SOAK>

Locked-AutomaticInService to Unlocked transition soak time as measured in 15-minute intervals. Defaults to 32.

<NAME>

NAME is a string. Defaults to NULL. Maximum length is 32 characters.

<CMDMDE>

Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that could make the command fail.

<PST>

Primary state. Defaults to Unlocked. The parameter type is PST, which indicates the current overall service condition of an entity.

Unlocked

In service

Locked

Out of service

<SST>

Secondary state. Defaults to AutomaticInService. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


11.48  ED-SYNCN

The Edit Synchronization (ED-SYNCN) command edits the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock. For each clock, up to three synchronization sources can be specified (such as PRIMARY, SECOND, and THIRD).To view or edit the system timing mode, use the RTRV-NE-SYNCN or ED-NE-SYNCN commands.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.


Note To retrieve/set the timing mode, SSM message Set or Quality of RES information, use the RTRV-NE-SYNCN and ED-NE-SYNCN commands.


Category

Synchronization

Security

Provisioning

Input Format

ED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>],[SEC=<SEC>],[THIRD=<THIRD>][:];

Input Example

ED-SYNCN:BOYES:SYNC-NE:112:::PRI=INTERNAL,SEC=INTERNAL,THIRD=INTERNAL;

Input Parameters

<AID>

Access identifier from the "SYNC_REF" section.

<PRI>

(Optional) Primary reference of the synchronization from the "SYN_SRC" section.

<SEC>

(Optional) Secondary reference of the synchronization from the "SYN_SRC" section.

<THIRD>

(Optional) Third reference of the synchronization from the "SYN_SRC" section.


11.49  ED-TRAPTABLE

The Edit Trap Table (ED-TRAPTABLE) command edits a trap destination entry identified by a specific trap destination address.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

System

Security

Provisioning

Input Format

ED-TRAPTABLE:[<TID>]:<AID>:<CTAG>:::COMMUNITY=<COMMUNITY>,
[TRAPPORT=<TRAPPORT>],[TRAPVER=<TRAPVER>];

Input Example

ED-TRAPTABLE::1.2.3.4:1:::COMMUNITY="PUBLIC",TRAPPORT=162,TRAPVER=SNMPV1;

Input Parameters

<AID>

Access identifier from the "IPADDR" section. IP address identifying the trap destination.

<COMMUNITY>

Community name associated to the trap destination. Maximum of 32 characters. COMMUNITY is a string.

<TRAPPORT>

(Optional) UDP port number associated with the trap destination. Default to 162. TRAPPORT is an integer.

<TRAPVER>

(Optional) SNMP version number. Defaults to SNMPv1. The parameter type is SNMP_VERSION (SNMP version).

SNMPV1

SNMP version 1 (default)

SNMPV2

SNMP version 2


11.50  ED-TRC-OCH

The Edit Trace (ED-TRC-OCH) command edits trace-related optical channel facilities. Refer to the Cisco ONS SONET TL1 Reference Guide for specific card provisioning rules.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

DWDM

Security

Provisioning

Input Format

ED-TRC-OCH:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>],[TRC=<TRC>],
[TRCMODE=<TRCMODE>],[TRCLEVEL=<TRCLEVEL>],[TRCFORMAT=<TRCFORMAT>][:];

Input Example

ED-TRC-OCH:CISCO:CHAN-6-2:10:::EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCLEVEL=TTI-PM,TRCFORMAT=64-BYTE;

Input Parameters

<SRC>

Source access identifier from the "CHANNEL" section.

<EXPTRC>

(Optional) Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). A null value is equivalent to ALL. EXPTRC is a string.

<TRC>

(Optional) The path trace message to be transmitted. The trace byte continuously transmits a 64 byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (Hex 00) and CR and LF. A null value is equivalent to ALL.

<TRCMODE>

(Optional) Trace mode. Defaults to the OFF mode. A null value is equivalent to ALL. The parameter type is TRCMODE (trace mode).

AUTO

Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.

AUTO-NO-AIS

Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

MAN

Use the provisioned expected string as the expected string.

MAN-NO-AIS

Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.

OFF

Turn off path trace capability. Nothing will be reported.

<TRCLEVEL>

(Optional) The trace level to be managed. A null value is equivalent to ALL. TRCLEVEL is a string.

<TRCFORMAT>

(Optional) Trace message size. A null value is equivalent to ALL. The parameter type is TRCFORMAT (trace format).

1-BYTE

1-byte trace message

16-BYTE

16-byte trace message

64-BYTE

64-byte trace message


11.51  ED-USER-SECU

The Edit User Security (ED-USER-SECU) command edits a user's privileges, password, or ID. Only a Superuser can perform this operation. Privilege levels are described in the ENT-USER-SECU command.

Usage Guidelines

Passwords are masked for the following security commands: ACT-USER, ED-PID, ENT-USER-SECU and ED-USER-SECU. Access to a TL1 session by any means will have the password masked. The CTC Request History and Message Log will also show the masked commands. When a password-masked command is reissued by double-clicking the command from CTC Request History, the password will still be masked in the CTC Request History and Message Log. The actual password that was previously issued will be sent to the NE. To use a former command as a template only, single-click the command in CTC Request History. The command will be placed in the Command Request text box, where you can edit the appropriate fields prior to reissuing it.

Although the CTC allows both <UID> and <PID> of up to 20 characters, the CTC-entered users (<UID>, <PID>) are not valid TL1 users (for example, if issuing an ACT-USER command and using the CTC-entered <UID> that is greater than 10 characters long, TL1 will respond with DENY.

For the ED-USER-SECU command:

ED-USER-SECU:[TID]:<UID>:[CTAG]::[<NEWUID>],[<NEWPID>],,[<UAP>]:;

If the <NEWPID> is specified, the syntax is checked.

The syntax of <UID> is not checked.

Old users can change their password without changing their user ID, but the new password must meet the new requirements.

The <NEWPID> is required when changing the <USERID>.

In this release, when <NEWUID> is specified, <NEWPID> (and the <UAP>) become mandatory, but it is possible to change a USERID without changing the password by providing the same password. A user cannot keep his old password if the old password does not meet the new syntax requirements. For example:

<USERID> = CISCO2345
<PASSWORD>=CISCO#234 /*PASSWORD ALREADY MEETS REQUIREMENTS*/

ED-USER-SECU::CISCO2345:1::CISCO3456,CISCO#234,,PROV;

TCCP 1970-01-02 13:15:35 M 1 COMPLD;

<NEWUSERID> = CISCO60
<USERID> = CISCO40 <PASSWORD>=CISCO40 /*PASSWORD DOES NOT MEET REQUIREMENTS*/

ED-USER-SECU::CISCO40:1::CISCO60,CISCO40,,PROV;

BRONCOS4 1970-01-02 13:14:24 M 1 DENY IIFM /* INVALID PASSWORD */ ;

The ED-USER-SECU command should be used to change the default password (empty) for the CISCO15 default Superuser.

The ED-PID command cannot be used to change the empty password to a valid password.

Category

Security

Security

Superuser

Input Format

ED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:];

Input Example

ED-USER-SECU:PETALUMA:CISCO15:123::NEWUID,NEWPID,,MAINT;

Input Parameters

<UID>

User's identifier. Minimum UID is 6 characters. Maximum UID is 10 characters. UID is a string.

<NEWUID>

(Optional) User's new identifier. Minimum UID is 6 characters. Maximum UID is 10 characters. NEWUID is a string.

<NEWPID>

(Optional) User's new password. Minimum UID is 6 characters. Maximum UID is 10 characters. NEWPID is a string.

<UAP>

(Optional) User's access privilege. The parameter type is PRIVILEGE, which is the security level.

MAINT

Maintenance security level. 60 minutes of idle time.

PROV

Provision security level. 30 minutes of idle time.

RTRV

Retrieve security level. Unlimited idle time.

SUPER

Superuser security level. 15 minutes of idle time.


11.52  ED-VCG

The Edit Virtual Concatenated Group (ED-VCG) command edits the attributes of a VCG.

Usage Guidelines

None

Category

VCAT

Security

Provisioning

Input Format

ED-VCG:[<TID>]:<SRC>:<CTAG>:::[TXCOUNT=<TXCOUNT>],[NAME=<NAME>];

Input Example

ED-VCG:NODE1:FAC-1-1:1234:::TXCOUNT=7,NAME="VCG2";

Input Parameters

<SRC>

Source access identifier from the "FACILITY" section.

<TXCOUNT>

(Optional) Number of members in the transmit direction. For ML1000-2 and ML100T-12 cards, the only valid value is 2. For the FC_MR-4 card, the only valid value is 8. TXCOUNT is an integer.

<NAME>

(Optional) Name of the VCAT group. Maximum length is 64 characters. NAME is a string.


11.53  ED-WDMANS

The Edit Wavelength Division Multiplexing Automatic Node Set Up (ED-WDMANS) command edits the optical node setup application (ANS) attributes.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

ED-WDMANS:[<TID>]:<AID>:<CTAG>:::[POWER-IN=<POWERIN>],
[POWER-OUT=<POWEROUT>],[POWER-EXP=<POWEREXP>],[NTWTYPE=<NTWTYPE>];

Input Example

ED-WDMANS:PENNGROVE:WDMANS-W:114:::POWER-IN=10.0,POWER-OUT=10.0,
NTWTYPE=METRO-CORE;

Input Parameters

<AID>

Access identifier from the "WDMANS" section.

<POWERIN>

(Optional) Input power for OADM section of an OADM optical NE. POWERIN is a float expressed dBm.

<POWEROUT>

(Optional) Output power for OADM or muliplex/demultiplex section of HUB, TERMINAL, or OADM optical NE. POWEROUT is a float that is expressed in dBm.

<POWEREXP>

(Optional) Express power for OADM section. POWEREXP is a float.

<NTWTYPE>

(Optional) Network type where a DWDM node is installed. The parameter type is DWDM_RING_TYPE, which is the network type where the NE is installed.

METRO-ACCESS

The network where a DWDM node is installed is a metro access network.

METRO-CORE

The network where a DWDM node is installed is a metro core network.

NONE

A node that does not have a standard DWDM configuration.