Cisco ONS 15454 SDH TL1 Command Guide, Release 7.2
Chapter 10, DLT Commands
Downloads: This chapterpdf (PDF - 339.0KB) The complete bookPDF (PDF - 12.29MB) | Feedback

DLT Commands

Table Of Contents

DLT Commands

10.1  DLT-<MOD1PAYLOAD>

10.2  DLT-<MOD_RING>

10.3  DLT-BULKROLL-<STM_TYPE>

10.4  DLT-CRS-<PATH>

10.5  DLT-EQPT

10.6  DLT-FFP-<MOD2DWDMPAYLOAD>

10.7  DLT-FFP-<STM_TYPE>

10.8  DLT-LMP-CTRL

10.9  DLT-LMP-TLINK

10.10  DLT-LMP-DLINK

10.11  DLT-LNK

10.12  DLT-LNKTERM

10.13  DLT-OCHCC

10.14  DLT-OCHNC

10.15  DLT-OSC

10.16  DLT-RMONTH-<MOD2_RMON>

10.17  DLT-ROLL-<MOD_PATH>

10.18  DLT-ROUTE

10.19  DLT-ROUTE-GRE

10.20  DLT-TADRMAP

10.21  DLT-TRAPTABLE

10.22  DLT-TUNNEL-FIREWALL

10.23  DLT-TUNNEL-PROXY

10.24  DLT-USER-SECU

10.25  DLT-VCG


DLT Commands


This chapter provides delete (DLT) commands for the Cisco ONS 15454 SDH.

10.1  DLT-<MOD1PAYLOAD>

The Delete 10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, EC1, ESCON, ETRCLO, GIGE, HDTV, ISC3PEER1G, ISC3PEER2G, ISC3PEER2R, ISCCOMPAT, STM4, STM64, STM1, STM16, or T3 (DLT-<MOD1PAYLOAD>) command deletes the specified port. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Ports

Security

Provisioning

Input Format

DLT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

DLT-GIGE:TID:FAC-5-1:1;

Input Parameters

AID

Access identifier from the "FACILITY" section.


10.2  DLT-<MOD_RING>

The Delete MS-SPRing (DLT-<MOD_RING>) command deletes the multiplex section-shared protection ring (MS-SPRing) of the NE.

Usage Guidelines

The following actions will return error messages:

If the system fails on getting the information object repository (IOR), a SROG (Status, Get IOR Failed) error message is returned.

If the AID is invalid, an IIAC (Invalid AID) error message is returned.

If the MS-SPRing does not exist, a SRQN (MSSPR Does Not Exist) error message is returned.

The SROF (Facility Not Provisioned) or (Cannot Access MSSPR) error message is returned for an invalid query.

If the MS-SPRing is in use, a SROF (MSSPR In Use) error message is returned.

The SRQN (MSSPR Deletion Failed) error message is returned for an invalid deletion query.


Note The ALL AID is invalid for this command.



Note The list AID format has been supported since Release 4.6.


Category

MS-SPRing

Security

Provisioning

Input Format

DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::];

Input Example

DLT-MSSPR:PETALUMA:MSSPR-2:123;

Input Parameters

<AID>

Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE. ALL or MSSPR-ALL AID is not allowed for editing MS-SPRing.


10.3  DLT-BULKROLL-<STM_TYPE>

The Delete Bulkroll for STM4, STM64, STM1, or STM16 (DLT-BULKROLL-STM_TYPE) command deletes an attempted bulk rolling operation of a facility or completes an attempted rolling operation. This command is used for bulk line level rolling. Use DLT-ROLL-<MOD_PATH> for single path level rolling. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

DLT-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],WHY=<WHY>;

Input Example

DLT-BULKROLL-STM4:CISCO:FAC-1-1:6:::RFROMSTART=VC4-1-1-1,
RFROMEND=VC4-1-1-11,WHY=STOP;

Input Parameters

<FROM>

One of the end points. Access identifier from the "FACILITY" section for line level rolling and bulk rolling.

<RFROMSTART>

(Optional) The starting time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (VC or VC11).

<RFROMEND>

(Optional) The ending time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (VC or VC11).

<WHY>

The reason for deletion. The parameter type is WHY, which is the reason for deletion.

END

Drop the leg to be rolled. The leg is identified by the RFROM in the ENT-ROLL or ENT-BULKROLL command.

STOP

The rolling operation will be aborted and reverted to the previous configuration.


10.4  DLT-CRS-<PATH>

The Delete Cross-Connection for VC3, VC44C, VC38C, VC464C, VC48C, VC36C, VC4, VC416C, VC42C, VC43C, or VC12 (DLT-CRS-<PATH>) command deletes a cross-connection between VC paths. VC paths are specified using their VC AID. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The fields after CTAG (trailing colons) are optional.

For the 1-way cross-connections, the AIDs must be in the same order as originally entered; for the 2-way cross-connections, either order will work.

This command does not support deleting multiple VC cross-connections.

Using "&" in the AID field of this command can delete an subnetwork connection protection (SNCP) virtual container (VC) cross-connection.

The following command is used to delete a 1-way selector or 2-way selector and bridge with:

from points: F1, F2

to point: T1

DLT-CRS-{VC_PATH}:[<TID>]:F1&F2,T1:<CTAG>;

The following command is used to delete a 1-way bridge or 2-way selector and bridge with:

from point: F1

to points: T1, T2

DLT-CRS-{VC_PATH}:[<TID>]:F1,T1&T2:<CTAG>;

The following command is used to delete a 1-way or 2-way subtending SNCP connection with:

from points: F1, F2

to points: T1, T2

DLT-CRS-{VC_PATH}:[<TID>]:F1&F2,T1&T2:<CTAG>;

The AID format in the deletion command is the same as the AID format in the retrieved response message. For example, if the output of any retrieved AID is "F1&F2,T1:CCT,VC4", the deletion command with the AID format F1&F2,T1 is required to delete this cross-connection.

The following command is used to delete a SNCP IDRI cross-connection:

DLT-CRS-{VC_PATH}:[<TID>]:A&B,C&D:<CTAG>;

A-Path on ring X to which traffic from ring Y is bridged

B-Path on ring X to which traffic from the same ring is bridged

C-Path on ring Y to which traffic from ring X is bridged

D-Path on ring Y to which traffic from the same ring is bridged

A, B, C, and D have a positional meaning. Connection type 2WAYDC is used for SNCP IDRI cross-connections.

The following command is used to delete a SNCP dual-ring interconnect (DRI) cross-connection:

DLT-CRS-{VC_PATH}:[<TID>]:A&B,C:<CTAG>;

A-Path on ring X to which traffic from ring Y is bridged

B-Path on ring X to which traffic from the same ring is bridged

C-Traffic to and from ring Y

A, B, and C have a positional meaning. Connection type 2WAYDC is used for SNCP DRI cross-connections.

All A&B AIDs in the TL1 cross-connection command are in the format of WorkingAID&ProtectAID.

You can experience some implementation behavior problems if additional drops have been added to the connection object.

The facility AID is only valid for slots holding the G1K-4 card.

The virtual facility AID (VFAC) is only valid on slots holding an ML-Series card.

CKTID is a string of ASCII characters. The maximum length of CKTID can be 48 characters. If the CKTID is EMPTY or NULL, the field will not appear.

Category

Cross Connections

Security

Provisioning

Input Format

DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::CKTID=<CKTID>,]
[CMDMDE=<CMDMDE>];

Input Example

DLT-CRS-VC44C:VINBURG:VC4-1-1-1,VC4-12-1-1:102:::CKTID=CKTID,CMDMDE=NORM;

Input Parameters

<SRC>

Source AID from the "CrossConnectId1" section.

<DST>

Destination AID from the "CrossConnectId1" section.

<CKTID>

(Optional) CKTID is a string. CKTID contains the common language circuit ID or other alias of the circuit being provisioned. May not contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<CMDMDE>

(Optional) Command Mode. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect from Unlocked-Enabled or Locked-Disabled, AutomaticInService service states. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.

FRCD

Force the system to override a state where the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that might make the command fail.


10.5  DLT-EQPT

The Delete Equipment (DLT-EQPT) deletes a card from the NE. This command removes the card type and attributes that were entered for a particular slot. If any facilities are assigned, they are deleted too.

The DLT-EQPT command also deletes a shelf that is no longer used. A shelf can only be deleted if there is no equipment present or if the equipment and it's attributes are not in use and can be deleted as well. Only one REPT DBCHG on SHELF-{1-8} will be reported in the latter case. The node controller shelf (the shelf whose shelf ID is 1) cannot be deleted.

Usage Guidelines

The command will be denied if the card is part of a protection group or has a cross-connect endpoint. To delete a card that is part of a protection group, it has to be removed from the protection group first using the ED-EQPT command.

Error conditions for deleting equipment can be:

The error message SPLD (Equipment In Use) will be returned in the following conditions:

The card is in a protection group.

The card has a cross-connection or a data communications channel/generic communications channel/optical service channel (DCC/GCC/OSC) termination, or provisionable patchcord termination.

Any of its facilities are being used as a synchronization source.


Note If a card is not provisioned, an error message will be returned.


Category

Equipment

Security

Provisioning

Input Parameters

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::];

Input Example

DLT-EQPT:SONOMA:SLOT-1:104;

Input Parameters

<AID>

Access identifier from the "EQPT" section. Identifies an equipment unit (slot) to act on.


10.6  DLT-FFP-<MOD2DWDMPAYLOAD>

Delete Facility Protection Group for 10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, ETRCLO, GIGE, HDTV, ISC1, ISC3, or PASSTHRU (DLT-FFP-<MOD2DWDMPAYLOAD>) command deletes Y-cable protection on client facilities.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>,<DST>:<CTAG>[:::];

Input Example

DLT-FFP-HDTV:CISCO:FAC-1-1-1,FAC-2-1-1:100;

Input Parameters

<SRC>

Source AID from the "FACILITY" section.

<DST>

Destination AID from the "FACILITY" section.


10.7  DLT-FFP-<STM_TYPE>

The Delete Facility Protection Group for STM4, STM64, STM1, or STM16 (DLT-FFP-<STM_TYPE>) command deletes an synchronous transfer mode (STM) facility protection group in a 1+1 architecture. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

If the protection group does not exist, an error message will be returned.

Category

Protection

Security

Provisioning

Input Format

DLT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::];

Input Example

DLT-FFP-STM1:PETALUMA:FAC-2-1,FAC-1-1:1;

Input Parameters

<WORK>

The working facility AID from the "FACILITY" section.

<PROTECT>

The protect facility AID from the "FACILITY" section.


10.8  DLT-LMP-CTRL

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Delete Link Management Protocol Control Channel (DLT-LMP-CTRL) command deletes an LMP control channel.

Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

DLT-LMP-CTRL:[<TID>]:<SRC>:<CTAG>;

Input Example

DLT-LMP-CTRL:PETALUMA:CTRL-3:704;

Input Parameters

<SRC>

The LMP control channel.

CTRL-ALL

Specifies all the control channels.

CTRL-{1-4}

Specifies an individual control channel.


10.9  DLT-LMP-TLINK

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Delete Link Management Protocol Traffic Engineering (TE) Link (DLT-LMP-TLINK) command deletes an LMP TE link.

Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

DLT-LMP-TLINK:[<TID>]:<SRC>:<CTAG>;

Input Example

DLT-LMP-TLINK:PETALUMA:TLINK-3:704;

Input Parameters

<SRC>

LMP TE link.

TLINK-ALL

Specifies all the TE links.

TLINK-{1-256}

Specifies an individual TE link.


10.10  DLT-LMP-DLINK

(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Delete Link Management Protocol Data Link (DLT-LMP-DLINK) command deletes an LMP data link.

Usage Guidelines

This command is only applicable on a node that supports the LMP protocol, and that has the LMP protocol enabled.

Category

LMP

Security

Provisioning

Input Format

DLT-LMP-DLINK:[<TID>]:<SRC>:<CTAG>;

Input Example

DLT-LMP-DLINK:PETALUMA:FAC-14-1-1:704;

Input Parameters

<SRC>

Access identifier from the "FACILITY" section.


10.11  DLT-LNK

The Delete Optical Link for OCH, OMS, or OTS (DLT-LNK) command deletes an optical link between two optical connection points. Optical link is specified by using the AID of the involved optical connection points.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-LNK:[<TID>]:<FROM>,<TO>:<CTAG>;

Input Example

DLT-LNK:PENNGROVE:BAND-6-1-TX,BAND-13-1-RX:114;

Input Parameters

<FROM>

The identifier at one end of the optical link from the AID "BAND" section.

<TO>

The identifier at the other end of the optical link from the AID "BAND" section.


10.12  DLT-LNKTERM

The Delete a Provisionable Patchcord Termination (DLT-LNKTERM) command deletes a provisionable patchcord termination present on a node. All termination points of a link/provisionable patchcord have to be deleted for the link to be deleted fully.

Usage Guidelines

This command accepts multiple AIDs, but does not accept the ALL AID.

A suitable error will be returned if the link termination does not exist.

Category

Provisionable Patchcords

Security

Provisioning

Input Format

DLT-LNKTERM:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-LNKTERM::LNKTERM-1:CTAG;

Input Parameters

<AID>

Access identifier from the "LNKTERM" section. Indicates a link (provisionable patchcord) termination on the local node.


10.13  DLT-OCHCC

The Delete Optical Channel Client Connection (DLT-OCHCC) command deletes the OCH client connection.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],[CMDMDE=<CMDMDE>];

Input Example

DLT-OCHCC:VA454-22:FAC-2-1-1:116:::CKTID=\"OCHCC-1\",CMDMDE=FRCD;

Input Parameters

<AID>

Access identifier from the "FACILITY" section.

<CKTID>

(Optional) The default is Blank or None. String of ASCII characters. Maximum length is 48. Circuit identification parameter contains the Common Language Circuit ID or other alias of the circuit being provisioned. Cannot contain blank spaces. CKTID is a string of ASCII characters. The maximum length of CKTID can be 48.

<CMDMDE>

(Optional) The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that may make the command fail.


10.14  DLT-OCHNC

(Cisco ONS 15454) The Delete Optical Channel Network Connection (DLT-OCHNC) command deletes the optical channel (OCH) network connection.

Usage Guidelines

Two network connection channel endpoints must be specified in order to identify the wavelength channel inside the node.

Category

DWDM

Security

Provisioning

Input Format

DLT-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>],[CMDMDE=<CMDMDE>];

Input Example

DLT-OCHNC:VA454-22:CHANWL-1-3-TX-1530.33,
CHANWL-4-1-RX-1530.33:116:::CKTID=CIRCUIT,CMDMDE=FRCD;

Input Parameters

<SRC>

Source access identifier from the "CHANNEL" section. In two-way wavelength connection sources, both directions need to be indicated.

<DST>

Destination access identifier from the "LINEWL" section. In a two-way wavelength connection destination, both directions need to be indicated.

<CKTID>

(Optional) Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48.

<CMDMDE>

(Optional) The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that may make the command fail.


10.15  DLT-OSC

The Delete Optical Service Channel (DLT-OSC) command deletes the OSC group of the NE.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-OSC:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-OSC:PENNGROVE:OSC-1:114;

Input Parameters

<AID>

Access identifier from the "OSC" section. Identifies the OSC group of the NE.


10.16  DLT-RMONTH-<MOD2_RMON>

The Delete Remote Monitoring Threshold for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, FSTE, G1000, GFPOS, GIGE, OCH, or POS (DLT-RMONT-<MOD2_RMON>) command deletes a threshold entry in the remote monitoring (RMON) alarm table. Because there can be multiple thresholds created for a particular montype, you must specify all the necessary parameters for the specific threshold that you want to delete. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Performance

Security

Provisioning

Input Format

DLT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,<INTVL>:
RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE],[STARTUP=<STARTUP>][:];

Input Example

DLT-RMONTH-GIGE:CISCO:FAC-2-1:1234::ETHERSTATSOCTETS,,,,100:RISE=1000,FALL=100
SAMPLE=DELTA,STARTUP=RISING;

Input Parameters

<SRC>

Source access identifier from the "FACILITY" section. AID for the facility that manages the data statistics.

<MONTYPE>

Monitored type. Type of RMON monitored data statistics. The parameter type is ALL_MONTYPE, which is the monitoring type list.

AISSP

Alarm Indication Signal SecondsPath

ALL

All possible values

BBEP

SDH Background Block Errors Path

BBE-PM

OTN—Background Block Errors—Path Monitor Point

BBER

SDH Background Block Error Ratio

BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as one tenth of a percentage

BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as one tenth of a percentage

BBE-SM

OTN—Background Block Errors—Section Monitor Point

BIEC

FEC—Bit Errors Corrected

CGV

8B10B—Code Group Violations

CVCPP

Coding Violations—CP-Bit Path

CVL

Coding Violations—Line

CVP

Coding Violations—Path

CVS

Coding Violations—Section

CVV

Coding Violations—Section

DCG

8B10B—Data Code Groups

ESCPP

Errored Seconds—CPBit Path

ESL

Errored Seconds—Line

ESP

Errored Seconds—Path

ES-PM

OTN—Errored Seconds—Path Monitor Point

ESR

Errored Second—Ratio

ESR-PM

Errored Seconds Ratio—Path Monitor Point expressed as one tenth of a percentage

ESR-SM

Errored Seconds Ratio—Section Monitor Point expressed as one tenth of a percentage

ESS

Errored Seconds—Section

ES-SM

OTN—Errored Seconds—Section Monitor Point

ESV

Errored Seconds—VC Path

etherStatsBroadcastPkts

The total number of good packets received that were directed to a multicast address

etherStatsCollisions

Number of transmit packets that are collisions

etherStatsCRCAlignErrors

The total number of packets received that have a length (excluding framing bits, but including frame check sequence [FCS] octets) of between 64 and 1518 octets

etherStatsDropEvents

Number of received frames dropped at the port level

etherStatsFragments

The total number of packets received that were less than 64 octets

etherStatsJabbers

The total number of packets received that are longer than 1518 octets

etherStatsOctets

The total number of octets of data

etherStatsOversizePkts

The total number of packets received that are longer than 1518 octets

etherStatsPkts

The total number of packets (including bad packets, broadcast packets, and multicast packets) received

etherStatsUndersizePkts

The total number of packets received that are less than 64 octets

FCP

Failure Count—Line

FC-PM

OTN—Failure Count—Path Monitor Point

FC-SM

OTN—Failure Count—Section Monitor Point

HP-AR

Availability Ratio

HP-BBE

High-Order Path Background Block Error

HP-BBER

High-Order Path Background Block Error Ratio

HP-EB

High-Order Path Errored Block

HP-ES

High-Order Path Errored Second

HP-ESA

High-Order Path Errored Seconds-A

HP-ESB

High-Order Path Errored Seconds-B

HP-ESR

High-Order Path Errored Second Ratio

HP-FC

High-Order Path Failure Count

HP-NPJC-PDET

High Order Path Negative Pointer Justification Count

HP-NPJC-PGEN

High Order Path Pointer Justification Count Seconds

HP-OI

Outage Intensity

HP-PJCDIFF

High Order Path Pointer Justification Count Difference

HP-PJCS-PDET

High Order Path Pointer Justification Count

HP-PPJC-PDET

High Order Path Positive Pointer Justification Count

HP-PPJC-PGEN

High Order Path, Positive Pointer Justification Count

HP-SEPI

The number of SEP events in available time

HP-SES

High-Order Path Severely Errored Seconds

HP-SESR

High-Order Path Severely Errored Second Ratio

HP-UAS

High-Order Path Unavailable Seconds

ifInBroadcastPkts

Number of broadcast packets received since the last counter reset

ifInDiscards

The number of inbound packets

ifInErrorBytePktss

Receive Error Byte

ifInErrors

The number of inbound packets (or transmission units) that contained errors

ifInFramingErrorPkts

Receive Framing Error

ifInJunkInterPkts

Receive Interpacket Junk

ifInMulticastPkts

Number of multicast packets received since the last counter reset

ifInOctets

Number of bytes transmitted since the last counter reset

ifInUcastPkts

Number of unicast packets received since the last counter reset

ifOutBroadcastPkts

Number of broadcast packets transmitted

ifOutDiscards

The number of outbound packets

ifOutErrors

The number of outbound packets (or transmission units) that could not be transmitted because of errors

ifOutMulticastPkts

Number of multicast packets transmitted

ifOutPayloadCrcErrors

Received payload cyclic redundancy check (CRC) errors

ifOutUcastPkts

Number of unicast packets transmitted

IOS

8B10B-Idle Ordered Sets

IPC

Invalid Packet Count

LBCL-AVG

Average Laser Bias current in micro A

LBCL-MAX

Maximum Laser Bias current in micro A

LBCL-MIN

Minimum Laser Bias current in micro A

LBCN

Normalized Laser Bias Current for STM1-8

LBCN-HWT

Laser bias current

LBCN-LWT

Laser bias current

LOSSL

Loss of Signal Seconds—Line

LP-BBE

Low-Order Path Background Block Error

LP-BBER

Low-Order Path Background Block Error Ratio

LP-EB

Low-Order Path Errored Block

LP-ES

Low-Order Path Errored Second

LP-ESA

Low-Order Path Errored Seconds-A

LP-ESB

Low-Order Path Errored Seconds-B

LP-ESR

Low-Order Path Errored Second Ratio

LP-FC

Low-Order Path Failure Count

LP-NPJC-DET

Low Order Negative Pointer Justification Count, Detected

LP-NPJC-GEN

Low Order Negative Pointer Justification Count, Generated

LP-PPJC-DET

Low Order Positive Pointer Justification Count, Detected

LP-PPJC-GEN

Low Order positive Pointer Justification Count, Generated

LP-SEP

A sequence of between 3 to 9 consecutive severely errored seconds (SES)

LP-SEPI

Low-Order Path Severely Errored Period Intensity

LP-SES

Low-Order Path Severely Errored Seconds

LP-UAS

Low-Order Path Unavailable Seconds

MS-PSC

Protection switch count

MS-PSD

Protection switch duration

NIOS

8B10B—Non Idle Ordered Sets

NPJC-PDET

Negative Pointer Justification, Path Detected

NPJC-PGEN

Negative Pointer Justification, Path Detected

OPR-AVG

Average Receive Power in tenths of a microwatt

OPR-MAX

Maximum Receive Power in tenths of a microwatt

OPR-MIN

Minimum Receive Power in tenths of a microwatt

OPRN

Normalized Optical Receive Power for STM1-8

OPRN-MAX

Maximum value for OPRN

OPRN-MIN

Minimum value for OPRN

OPT-AVG

Average Transmit Power in tenths of a microwatt

OPT-MAX

Maximum Transmit Power in tenths of a microwatt

OPT-MIN

Minimum Transmit Power in tenths of a microwatt

OPTN

Normalized value for Optical Power Transmitted for STM1-8 card

OPTN-MAX

Maximum value for OPTN

OPTN-MIN

Minimum value for OPTN

OPWR-AVG

Optical Power—Average Interval Value in one tenth of dBm

OPWR-MAX

Optical Power—Maximum Interval Value in one tenth of dBm

OPWR-MIN

Optical Power—Minimum Interval Value in one tenth of dBm

PPJC-PDET

Positive Pointer Justification, Path Detected

PPJC-PGEN

Positive Pointer Justification, Path Detected

PSC

Protection Switching Count

PSC-R

Protection Switching Count—Ring

PSC-S

Protection Switching Count—Span

PSC-W

Protection Switching Count—Working

PSD

Protection Switching Duration

PSD-R

Protection Switching Duration—Ring

PSD-S

Protection Switching Duration—Span

PSD-W

Protection Switching Duration—Working

SASCPP

Severely Errored Framing/AIS Second—CP-Bit Path

SASP

Severely Errored Framing/AIS Seconds Path

SEFS

Severely Errored Framing Seconds

SESCPP

Severely Errored Second—CP-Bit Path

SESL

Severely Errored Second—Line

SESP

Severely Errored Second—Path

SES-PM

OTN—Severely Errored Second—Path

SESR

Severely Errored Second—Ratio

SESR-PM

OTN—Severely Errored Second Ratio—Path Monitor Point expressed as one tenth of a percentage

SESR-SM

OTN—Severely Errored Second Ratio—Section Monitor Point expressed as one tenth of a percentage

SESS

Severely Errored Second—Section

SES-SM

OTN—Severely Errored Second—Section Monitor Point

SESV

Severely Errored Second—VC Path

UASCPP

Unavailable Second—CP-Bit Path

UASL

Unavailable Second—Line

UASP

Unavailable Second—Path

UAS-PM

OTN—Unavailable Second—Path Monitor Point

UAS-SM

OTN—Unavailable Second—Section Monitor Point

UASV

Unavailable Second—VC Path

UNC-WORDS

FEC—Uncorrectable Words

VPC

Valid Packet Count

<INTVL>

The interval in seconds over which the data is sampled and compared with the rising and falling threshold. A valid value is any integer larger than or equal to 10 (seconds).

<RISE>

The rising threshold for the sampled statistics. A valid value is any integer.

<FALL>

The falling threshold. A valid value is any integer smaller than the rising threshold.

<SAMPLE>

(Optional) The method of calculating the value to be compared to the thresholds. The parameter type is SAMPLE_TYPE, which describes how the data will be calculated during the sampling period.

ABSOLUTE

Comparing directly.

DELTA

Comparing with the current value of the selected variable subtracted by the last sample.

<STARTUP>

(Optional) Dictates whether an event will generate if the first valid sample is greater than or equal to the rising threshold, less than or equal to the falling threshold, or both. The parameter type is STARTUP_TYPE, which indicates whether an event will be generated when the first valid sample is crossing the rising or falling threshold.

FALLING

Generates the event when the sample is smaller than or equal to the falling threshold.

RISING

Generates the event when the sample is greater than or equal to the rising threshold.

RISING-OR-FALLING

Generates the event when the sample is crossing the rising threshold, or the falling threshold.


10.17  DLT-ROLL-<MOD_PATH>

The Delete Roll for VC44C, VC464C, VC48C, VC4, VC416C, VC42C, or VC43C (DLT-ROLL-<MOD_PATH>) command deletes or completes an attempted rolling operation of a facility or completes an attempted rolling operation. See Table 27-1 for supported modifiers by platform.

Usage Guidelines

None

Category

Bridge and Roll

Security

Provisioning

Input Format

DLT-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::WHY=<WHY>;

Input Example

DLT-ROLL-VC4:CISCO:VC4-1-1-1,VC4-2-1-1:6:::WHY=STOP;

Input Parameters

<FROM>

Source access identifier from the "VC" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the FROM-AID termination point. Otherwise, FROM is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters.

<TO>

Destination AID from the "VC" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the TO-AID termination point. Otherwise, the TO is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters.

<WHY>

The reason for the deletion. The parameter type is WHY, which is the reason for the deletion.

END

Drop the leg to be rolled; the leg that is identified by the RFROM in the ENT-ROLL command.

STOP

The rolling operation will be deleted and reverted to the previous configuration.


10.18  DLT-ROUTE

The Delete Route (DLT-ROUTE) command deletes static routes.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-ROUTE:[<TID>]::<CTAG>::<DESPID>;

Input Example

DLT-ROUTE:CISCO::123::10.64.72.57;

Input Parameters

<DESPID>

Destination IP. DESPID is a string.


10.19  DLT-ROUTE-GRE

The Delete Route Generic Routing Encapsulation (DLT-ROUTE-GRE) command deletes a GRE tunnel.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-ROUTE-GRE:[<TID>]::<CTAG>:::IPADDR=<IPADDR>,
IPMASK=<IPMASK>,NSAP=<NSAP>;

Input Example

DLT-ROUTE-GRE:CISCO::123:::IPADDR=10.64.72.57,IPMASK=255.255.255.0,
NSAP=39840F80FFFFFF0000DDDDAA000010CFB4910200;

Input Parameters

<IPADDR>

IP address of the tunnel endpoint. IPADDR is a string.

<IPMASK>

Subnet mask for the tunnel endpoint. IPMASK is a string

<NSAP>

Network service access point (NSAP) address for the tunnel endpoint. NSAP is a string.


10.20  DLT-TADRMAP

The Delete TID Address Mapping (DLT-TADRMAP) command instructs a gateway NE to delete an entry in the TADRMAP table.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-TADRMAP:[<TID>]::<CTAG>:::[TIDNAME=<TIDNAME>],[ADDRTYPE=<ADDRTYPE>];

Input Example

DLT-TADRMAP:DXT::CTAG:::TIDNAME=ENENODENAME,ADDRTYPE=IP;

Input Parameters

<TIDNAME>

(Optional) TID of the entity to be removed from the TADRMAP. TIDNAME is a string.

<ADDRTYPE>

(Optional) Specifies to remove an IP, NSAP, or IP-AND-NSAP entry in the TADRMAP. The parameter type is ADDRTYPE, which specifies whether the address is and IP address or an NSAP address.

IP

IP address

IP-AND-NSAP

IP and NSAP address

NSAP

NSAP address


10.21  DLT-TRAPTABLE

The Delete Trap Table (DLT-TRAPTABLE) command deletes an SNMP trap destination entry.

Usage Guidelines

Entering ALL will delete the whole table.

Category

System

Security

Provisioning

Input Format

DLT-TRAPTABLE:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-TRAPTABLE::1.2.3.4:1;

Input Parameters

<AID>

Access identifier from the "IPADDR" section. IP address identifies the trap destination. Only numeric IP addresses are allowed.


10.22  DLT-TUNNEL-FIREWALL

The Delete Tunnel Firewall (DLT-TUNNEL-FIREWALL) command deletes a firewall tunnel.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-TUNNEL-FIREWALL:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>],
[SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>];

Input Example

DLT-TUNNEL-FIREWALL:TID::CTAG:::SRCADDR=192.168.100.52,
SRCMASK=255.255.255.0,DESTADDR=192.168.101.14,DESTMASK=255.255.255.0;

Input Parameters

<SRCADDR>

(Optional) Source IP address. SRCADDR is a string.

<SRCMASK>

(Optional) Source mask. SRCMASK is a string.

<DESTADDR>

(Optional) Destination IP address. DESTADDR is a string.

<DESTMASK>

(Optional) Destination mask. DESTMASK is a string.


10.23  DLT-TUNNEL-PROXY

The Delete Tunnel Proxy (DLT-TUNNEL-PROXY) command deletes a proxy tunnel.

Usage Guidelines

None

Category

System

Security

Provisioning

Input Format

DLT-TUNNEL-PROXY:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>],
[SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>];

Input Example

DLT-TUNNEL-PROXY:TID::CTAG:::SRCADDR=192.168.100.52,
SRCMASK=255.255.255.0,DESTADDR=192.168.101.14,DESTMASK=255.255.255.0;

Input Parameters

<SRCADDR>

(Optional) Source IP address. SRCADDR is a string.

<SRCMASK>

(Optional) Source mask. SRCMASK is a string.

<DESTADDR>

(Optional) Destination IP address. DESTADDR is a string.

<DESTMASK>

(Optional) Destination mask. DESTMASK is a string.


10.24  DLT-USER-SECU

The Delete User Security (DLT-USER-SECU) command deletes a user and can only be performed by a Superuser. Privilege levels are described in the ENT-USER-SECU command.

Usage Guidelines

This command cannot be used to delete a user that is currently logged on.

The syntax of <UID> is not checked. The user is deleted if the <UID> exists in the database.

Category

Security

Security

Superuser

Input Format

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>;

Input Example

DLT-USER-SECU:PETALUMA:CISCO15:123;

Input Parameters

<UID>

User identifier. Can be up to 10 alphanumeric characters. UID is a string.


10.25  DLT-VCG

The Delete Virtual Concatenated Group (DLT-VCG) command deletes a VCG object.

Usage Guidelines

None

Category

VCAT

Security

Provisioning

Input Format

DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:];

Input Example

DLT-VCG:NODE1:FAC-1-1:1234:::CMDMDE=FRCD;

Input Parameters

<SRC>

Source AID from the "FACILITY" section. ML-Series cards use VFAC AID and FC_MR-4 cards use FAC AID.

<CMDMDE>

(Optional) Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.

FRCD

Force the system to override a state where the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that might make the command fail.