Cisco ONS 15454 SDH Procedure Guide, Release 7.0
Chapter 10, Change Card Settings
Downloads: This chapterpdf (PDF - 214.0KB) The complete bookPDF (PDF - 15.96MB) | Feedback

Change Card Settings

Table Of Contents

Change Card Settings

Before You Begin

NTP-D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards

NTP-D89 Modify Line Settings and PM Parameter Thresholds for Optical Cards

NTP-D118 Modify Alarm Interface Controller-International Settings

NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection

NTP-D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards

NTP-D330 Change Card or PPM Service State

NTP-D331 Manage Pluggable Port Modules


Change Card Settings


This chapter explains how to change line and threshold settings on Cisco ONS 15454 SDH cards.

Before You Begin

Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide as necessary.


Caution Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards—As needed, complete this procedure to change line and threshold settings for all electrical cards (E1-N-14, E1-42, E3-12, DS3i-N-12, and STM1E-12).

2. D89 Modify Line Settings and PM Parameter Thresholds for Optical Cards—As needed, complete this procedure to change line and threshold settings for all optical (STM-N) cards.

3. D118 Modify Alarm Interface Controller-International Settings—As needed, complete this procedure to change external alarms and controls and/or orderwire settings.

4. D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection—As needed, complete this procedure to change the protection type on E-1 or DS-3 cards.

5. D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards—As needed, complete this procedure to change the FC_MR-4 card port and threshold settings.

6. D330 Change Card or PPM Service State—As needed, complete this procedure to change the service state on a card or pluggable port module (PPM).

7. D331 Manage Pluggable Port Modules—As needed, complete this procedure to provision a multirate PPM, assign the optical line rate, change the optical line rate, and delete PPMs.

NTP-D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards

Purpose

This procedure changes the line settings and performance monitoring (PM) parameter thresholds for electrical cards.

Tools/Equipment

None

Prerequisite Procedures

D17 Install the Electrical Cards

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Caution Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.


Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to change the electrical card settings. If you are already logged in, proceed to Step 2.

Step 2 As needed, complete the "NTP-D108 Back Up the Database" procedure to preserve the existing database.

Step 3 Perform any of the following tasks as needed:

D365 Change Line and Threshold Settings for E1-N-14 or E1-42 Cards

D340 Change Line and Threshold Settings for the E3-12 Cards

D341 Change Line and Threshold Settings for the DS3i-N-12 Cards

D342 Change Line and Threshold Settings for the STM1E-12 Card


Note To change settings on the Alarm Profiles tab, see Chapter 9 "Manage Alarms."


Step 4 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Stop. You have completed this procedure.


NTP-D89 Modify Line Settings and PM Parameter Thresholds for Optical Cards

Purpose

This procedure changes the line settings and the PM parameter thresholds for optical (STM-N) cards.

Tools/Equipment

None

Prerequisite Procedures

D16 Install STM-N Cards and Connectors

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Caution Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.


Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to change the STM-N card settings. If you are already logged in, proceed to Step 2.

Step 2 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Step 3 Perform any of the following tasks as needed:

D108 Change Line Settings for STM-N Cards

D343 Change SDH Threshold Settings for STM-N Cards

D109 Change Optics Thresholds Settings for STM-64 and MRC-12 Cards

D216 Change the STM-N Card ALS Maintenance Settings


Note To change settings on the Provisioning > VC4 tab, go to the "DLP-D122 Enable Intermediate Path Performance Monitoring" task. To change settings on the Alarm Profiles tab, see Chapter 9 "Manage Alarms."


Step 4 Complete the "NTP-D108 Back Up the Database" procedure.

Stop. You have completed this procedure.


NTP-D118 Modify Alarm Interface Controller-International Settings

Purpose

This procedure changes the AIC-I card external alarms and controls (environmental alarms) and changes orderwire settings.

Tools/Equipment

None

Prerequisite Procedures

D247 Provision External Alarms and Controls on the Alarm Interface Controller-International and the D83 Provision Orderwire.

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to change the AIC-I card settings. If you are already logged in, proceed to Step 2.

Step 2 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Step 3 Perform any of the following tasks as needed:

D208 Change External Alarms Using the AIC-I Card

D209 Change External Controls Using the AIC-I Card

D210 Change AIC-I Card Orderwire Settings

Step 4 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Stop. You have completed this procedure.


NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection

Purpose

This task converts E1-N-14 and DS3i-N-12 protect cards from 1:1 to 1:N protection.

Tools/Equipment

None

Prerequisite Procedures

D71 Create a 1:1 Protection Group

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to convert the E1-N-14 and DS3i-N-12 cards from 1:1 to 1:N protection. If you are already logged in, proceed to Step 2.

Step 2 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Step 3 Perform any of the following tasks as needed:

D176 Convert E1-N-14 Cards From 1:1 to 1:N Protection

D177 Convert DS3i-N-12 Cards From 1:1 to 1:N Protection

Step 4 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Stop. You have completed this procedure.


NTP-D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards

Purpose

This procedure changes the line settings and PM parameter thresholds for FC_MR-4 cards.

Tools/Equipment

None

Prerequisite Procedures

D286 Install the FC_MR-4 Cards

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to change the STM-N card settings. If you are already logged in, proceed to Step 2.

Step 2 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Step 3 Perform any of the following tasks as needed:

D354 Change General Port Settings for the FC_MR-4 Card

D355 Change Distance Extension Port Settings for the FC_MR-4 Card

D356 Change Enhanced FC/FICON Port Settings for the FC_MR-4 Card

D465 Create FC_MR-4 RMON Alarm Thresholds

D466 Delete FC_MR-4 RMON Alarm Thresholds

Step 4 As needed, complete the "NTP-D108 Back Up the Database" procedure.

Stop. You have completed this procedure.

NTP-D330 Change Card or PPM Service State

Purpose

This procedure changes a card or port's service state, which is an autonomously generated state that gives the overall condition of the port.

Tools/Equipment

None

Prerequisite Procedures

Chapter 2 "Install Cards and Fiber-Optic Cable"

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note On the STM64-XFP and MRC-12 cards, the PPM is equivalent to an optical port.



Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to change the card service state.

Step 2 Click the Inventory tab.

Step 3 Click Admin State for the card or PPM you want to change, and choose an administrative state from the drop-down list: Unlocked or Locked,maintenance.

Step 4 Click Apply.

Step 5 If an error message opens indicating that the card or PPM state cannot be changed from its current state, click OK.

Depending on the Admin State you choose, the card or port/PPM transitions to a different service state. For more information about the service states and card state transitions, refer to the "Administrative and Service States" appendix of the Cisco ONS 15454 SDH Reference Manual.

Stop. You have completed this procedure.

NTP-D331 Manage Pluggable Port Modules

Purpose

This procedure provisions, changes, and deletes PPMs for the MRC-12 and STM64-XFP cards. (STM64-XFP cards are single-rate PPMs, and therefore can only be deleted.)

Tools/Equipment

None

Prerequisite Procedures

D107 Preprovision an SFP or XFP Device or

D335 Install GBIC or SFP/XFP Devices

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task at the node where you want to provision, change, or delete PPMs. If you are already logged in, continue with Step 2.

Step 2 From the View menu, choose Go to Network View.

Step 3 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the D227 Disable Alarm Filtering as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide.

c. Complete the "DLP-D147 Export CTC Data" task to export alarm and condition information."DLP-D132 Provision a Multirate PPM on the MRC-12 Card" task

Step 4 As needed, complete the "DLP-D132 Provision a Multirate PPM on the MRC-12 Card" task. Single-rate PPMs do not require provisioning.

Step 5 As needed, complete the "DLP-D133 Provision the Optical Line Rate on the MRC-12 Card" task to assign an OC-3, OC-12, or OC-48 line rate.

Step 6 As needed, complete the "DLP-D134 Change the Optical Line Rate on the MRC-12 Card" task to change the line rate on a multirate PPM. You cannot change the optical line rate on single-rate PPMs.

Step 7 As needed, complete the "DLP-D135 Delete a PPM from the MRC-12 or STM64-XFP Card" task.

Stop. You have completed this procedure.