Cisco ONS 15454 SDH TL1 Command Guide, Release 6.0
Chapter 20, RST Commands
Downloads: This chapterpdf (PDF - 173.0KB) The complete bookPDF (PDF - 9.88MB) | Feedback

RST Commands

Table Of Contents

RST Commands

20.1  RST-<MOD2>

20.2  RST-EQPT


RST Commands


This chapter provides RST (restore) commands for the Cisco ONS 15454 SDH.

20.1  RST-<MOD2>

Restore (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS3I, DV6000, E1, E3, E4, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, STM4, STM64, STM1, STM16, OCH, OMS, OTS, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, STS36C, VC4, VC416C, VC42C, VC43C, VC11, VC12)

Usage Guidelines

This command provisions a facility in service.

See Table 27-1 on page 27-1 for supported modifiers by platform.

Category

Facility

Security

Maintenance

Related Commands

DLT-<MOD1PAYLOAD>

DLT-FFP-<MOD2DWDMPAYLOAD>

DLT-FFP-<STM_TYPE>

ED-<MOD1FCPAYLOAD>

ED-<MOD1FICONPAYLOAD>

ED-<MOD2DWDMPAYLOAD>

ED-<STM_TYPE>

ED-ALS

ED-DS3I

ED-E1/ED-E3/ED-E4

ED-FAC

ED-FFP-<MOD2DWDMPAYLOAD>

ED-FFP-<STM_TYPE>

ED-FSTE

ED-G1000

ED-GFP

ED-HDLC

ED-STM1E

ENT-<MOD1PAYLOAD>

ENT-FFP-<MOD2DWDMPAYLOAD>

ENT-FFP-<STM_TYPE>

INIT-REG-<MOD2>

OPR-ALS

OPR-LPBK-<MOD2>

OPR-PROTNSW-<MOD2DWDMPAYLOAD>

OPR-PROTNSW-<STM_TYPE>

REPT PM <MOD2>

RLS-LPBK-<MOD2>

RLS-PROTNSW-<MOD2DWDMPAYLOAD>

RLS-PROTNSW-<STM_TYPE>

RMV-<MOD2>

RTRV-<MOD1FCPAYLOAD>

RTRV-<MOD1FICONPAYLOAD>

RTRV-<MOD2DWDMPAYLOAD>

RTRV-<STM_TYPE>

RTRV-10GIGE

RTRV-ALMTH-<MOD2>

RTRV-ALS

RTRV-DS3I

RTRV-E1/RTRV-E3/RTRV-E4

RTRV-FAC

RTRV-FFP-<MOD2DWDMPAYLOAD>

RTRV-FFP-<STM_TYPE>

RTRV-FSTE

RTRV-G1000

RTRV-GFP

RTRV-GIGE

RTRV-HDLC

RTRV-PM-<MOD2>

RTRV-PMSCHED-<MOD2>

RTRV-POS

RTRV-PROTNSW-<MOD2DWDMPAYLOAD>

RTRV-PROTNSW-<STM_TYPE>

RTRV-STM1E

RTRV-TH-<MOD2>

SCHED-PMREPT-<MOD2>

SET-ALMTH-<MOD2>

SET-TH-<MOD2>


Input Format

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];

Input Example

RST-E1:CISCO:FAC-1-1:1::::UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

Table 20-1 RST-<MOD2> Input Parameters 

Parameter and Values
Description

AID

Access identifier from the "25.1  ALL" section on page 25-1

PST

Primary state

Parameter type is PST—indicates the current overall service condition of an entity

Unlocked

In service

Locked

Out of service

SST

Secondary state

Parameter type is SST—provides additional information pertaining to PST and PSTQ

AutomaticInService

Automatic in service

Disabled

Disabled

Loopback

Loopback

MismatchofEquipmentAlarm

Mismatch of equipment and attributes

Maintenance

Maintenance mode

OutOfGroup

Out of group

SoftwareDownload

Software downloading

Unassigned

Unassigned

NotInstalled

Unequipped


20.2  RST-EQPT

Restore Equipment

Usage Guidelines

This command provisions equipment into the In Service state from the Maintenance state.


Note Only applicable to equipment that is in transition from the Maintenance state to the In-Service state.


Category

Equipment

Security

Maintenance

Related Commands

ALW-SWDX-EQPT

ALW-SWTOPROTN-EQPT

ALW-SWTOWKG-EQPT

CHG-EQPT

DLT-EQPT

ED-EQPT

ENT-EQPT

INH-SWDX-EQPT

INH-SWTOPROTN-EQPT

INH-SWTOWKG-EQPT

REPT ALM EQPT

REPT EVT EQPT

REPT RMV EQPT

REPT RST EQPT

RMV-EQPT

RTRV-ALM-EQPT

RTRV-ALMTH-EQPT

RTRV-COND-EQPT

RTRV-EQPT

SET-ALMTH-EQPT

SW-DX-EQPT

SW-TOPROTN-EQPT

SW-TOWKG-EQPT


Input Format

RST-EQPT:[<TID>]:<AID>:<CTAG>[::];

Input Example

RST-EQPT:CISCO:SLOT-1:1;

Input Parameters

Table 20-2 RST-EQPT Input Parameters 

Parameter and Values
Description

AID

Access identifier from the "25.1.10  EQPT" section on page 25-15