Cisco ONS 15454 SDH TL1 Command Guide, Release 6.0
Chapter 15, INIT Commands
Downloads: This chapterpdf (PDF - 231.0KB) The complete bookPDF (PDF - 9.88MB) | Feedback

INIT Commands

Table Of Contents

INIT Commands

15.1  INIT-REG-<MOD2>

15.2  INIT-SYS


INIT Commands


This chapter provides INIT (initialize) commands for the Cisco ONS 15454 SDH.

15.1  INIT-REG-<MOD2>

Initialize Register (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS3I, DV6000, E1, E3, E4, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, STM4, STM64, STM1, STM16, OCH, OMS, OTS, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C, VC12)

See Table 27-1 on page 27-1 for supported modifiers by platform.

Usage Guidelines

This command initializes the performance monitoring (PM) registers.


NoteThe time period is always the current time period, and the previous time period counts are not cleared; therefore, both <MONDAT> and <MONTM> are not supported in this command.

All cards support only the (receive) RCV direction. BTH is not supported for this command.

INIT-REG-<MOD2> can also be used to initialize the (remote monitoring) RMON managed raw data.


Category

Performance

Security

Maintenance

Related Commands

ALW-PMREPT-ALL

DLT-<MOD1PAYLOAD>

DLT-FFP-<MOD2DWDMPAYLOAD>

DLT-FFP-<STM_TYPE>

DLT-RMONTH-<MOD2_RMON>

ED-<GIGE_TYPE>

ED-<MOD1FCPAYLOAD>

ED-<MOD1FICONPAYLOAD>

ED-<MOD2DWDMPAYLOAD>

ED-<STM_TYPE>

ED-ALS

ED-FFP-<MOD2DWDMPAYLOAD>

ED-FFP-<STM_TYPE>

ED-FSTE

ED-G1000

ED-GFP

ED-HDLC

ED-TRC-<MOD2DWDMPAYLOAD>

ED-TRC-<STM_TYPE>

ENT-<MOD1PAYLOAD>

ENT-FFP-<MOD2DWDMPAYLOAD>

ENT-FFP-<STM_TYPE>

ENT-RMONTH-<MOD2_RMON>

INH-PMREPT-ALL

OPR-ALS

OPR-LPBK-<MOD2>

OPR-PROTNSW-<MOD2DWDMPAYLOAD>

OPR-PROTNSW-<STM_TYPE>

REPT PM <MOD2>

RLS-LPBK-<MOD2>

RLS-PROTNSW-<MOD2DWDMPAYLOAD>

RLS-PROTNSW-<STM_TYPE>

RMV-<MOD2>

RST-<MOD2>

RTRV-<MOD1FCPAYLOAD>

RTRV-<MOD1FICONPAYLOAD>

RTRV-<MOD2DWDMPAYLOAD>

RTRV-<STM_TYPE>

RTRV-10GIGE

RTRV-ALMTH-<MOD2>

RTRV-ALS

RTRV-FAC

RTRV-FFP-<MOD2DWDMPAYLOAD>

RTRV-FFP-<STM_TYPE>

RTRV-FSTE

RTRV-G1000

RTRV-GFP

RTRV-GIGE

RTRV-HDLC

RTRV-PM-<MOD2>

RTRV-PMMODE-<VC_PATH>

RTRV-PMSCHED-<MOD2>

RTRV-PMSCHED-ALL

RTRV-POS

RTRV-PROTNSW-<MOD2DWDMPAYLOAD>

RTRV-PROTNSW-<STM_TYPE>

RTRV-RMONTH-<MOD2_RMON>

RTRV-TH-<MOD2>

RTRV-TH-ALL

RTRV-TRC-<MOD2DWDMPAYLOAD>

RTRV-TRC-<STM_TYPE>

SCHED-PMREPT-<MOD2>

SET-ALMTH-<MOD2>

SET-PMMODE-<VC_PATH>

SET-TH-<MOD2>


Input Format

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<lSTM>],[<DIRN>],[<TMPER>]
[,,];

Input Example

INIT-REG-STM1:CISCO:FAC-1-1:1234::CVL,,NEND,RCV,15-MIN;

Input Parameters

Table 15-1 INIT-REG-<MOD2> Input Parameters 

Parameter and Values
Description

AID

Access identifier from the "25.1  ALL" section on page 25-1. All of the VC12 and Facility AIDs are supported

MONTYPE

Monitored type

Parameter type is ALL_MONTYPE—monitoring type list

AISSP

Alarm Indication Signal SecondsPath

ALL

All possible values

BBEP

SDH Background Block Errors Path

BBE-PM

OTN—Background Block Errors—Path Monitor Point

BBER

SDH Background Block Error Ratio

BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as 1/10th of a percentage.

BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as 1/10th of a percentage.

BBE-SM

OTN—Background Block Errors—Section Monitor Point

BIEC

FEC—Bit Errors Corrected

CGV

8B10B—Code Group Violations

CVCPP

Coding Violations—CP-Bit Path

CVL

Coding Violations—Line

CVP

Coding Violations—Path

CVS

Coding Violations—Section

CVV

Coding Violations—Section

DCG

8B10B—Data Code Groups

ESCPP

Errored Seconds—CPBit Path

ESL

Errored Seconds—Line

ESP

Errored Seconds—Path

ES-PM

OTN—Errored Seconds—Path Monitor Point

ESR

Errored Second—Ratio

ESR-PM

Errored Seconds Ratio—Path monitor Point expressed as 1/10th of a percentage

ESR-SM

Errored Seconds Ratio—Section monitor Point expressed as 1/10th of a percentage

ESS

Errored Seconds—Section

ES-SM

OTN—Errored Seconds—Section Monitor Point

ESV

Errored Seconds—VC Path

etherStatsBroadcastPkts

The total number of good packets received that were directed to a multicast address

etherStatsCollisions

Number of transmit packets that are collisions

etherStatsCRCAlignErrors

The total number of packets received that have a length (excluding framing bits, but including frame check sequence [FCS] octets) of between 64 and 1518 octets

etherStatsDropEvents

Number of received frames dropped at the port level

etherStatsFragments

The total number of packets received that were less than 64 octets

etherStatsJabbers

The total number of packets received that are longer than 1518 octets

etherStatsOctets

The total number of octets of data

etherStatsOversizePkts

The total number of packets received that are longer than 1518 octets

etherStatsPkts

The total number of packets (including bad packets, broadcast packets, and multicast packets) received

etherStatsUndersizePkts

The total number of packets received that are less than 64 octets

FCP

Failure Count—Line

FC-PM

OTN—Failure Count—Path Monitor Point

FC-SM

OTN—Failure Count—Section Monitor Point

HP-AR

Availability Ratio

HP-BBE

High-Order Path Background Block Error

HP-BBER

High-Order Path Background Block Error Ratio

HP-EB

High-Order Path Errored Block

HP-ES

High-Order Path Errored Second

HP-ESA

High-Order Path Errored Seconds - A

HP-ESB

High-Order Path Errored Seconds - B

HP-ESR

High-Order Path Errored Second Ratio

HP-FC

High-Order Path Failure Count

HP-NPJC-PDET

High Order Path Negative Pointer Justification Count

HP-NPJC-PGEN

High Order Path Pointer Justification Count Seconds

HP-OI

Outage Intensity

HP-PJCDIFF

High Order Path Pointer Justification Count Difference

HP-PJCS-PDET

High Order Path Pointer Justification Count

HP-PPJC-PDET

High Order Path Positive Pointer Justification Count

HP-PPJC-PGEN

High Order Path, Positive Pointer Justification Count

HP-SEPI

The number of SEP events in available time

HP-SES

High-Order Path Severely Errored Seconds

HP-SESR

High-Order Path Severely Errored Second Ratio

HP-UAS

High-Order Path Unavailable Seconds

ifInBroadcastPkts

Number of broadcast packets received since the last counter reset

ifInDiscards

The number of inbound packets

ifInErrorBytePktss

Receive Error Byte

ifInErrors

The number of inbound packets (or transmission units) that contained errors

ifInFramingErrorPkts

Receive Framing Error

ifInJunkInterPkts

Receive Interpacket Junk

ifInMulticastPkts

Number of multicast packets received since the last counter reset

ifInOctets

Number of bytes transmitted since the last counter reset

ifInUcastPkts

Number of unicast packets received since the last counter reset

ifOutBroadcastPkts

Number of broadcast packets transmitted

ifOutDiscards

The number of outbound packets

ifOutErrors

The number of outbound packets (or transmission units) that could not be transmitted because of errors

ifOutMulticastPkts

Number of multicast packets transmitted

ifOutPayloadCrcErrors

Received payload (cyclic redundancy check) CRC errors

ifOutUcastPkts

Number of unicast packets transmitted

IOS

8B10B - Idle Ordered Sets

IPC

Invalid Packet Count

LBCL-AVG

Average Laser Bias current in micro A

LBCL-MAX

Maximum Laser Bias current in micro A

LBCL-MIN

Minimum Laser Bias current in micro A

LBCN

Normalized Laser Bias Current for STM1-8

LBCN-HWT

Laser Bias current

LBCN-LWT

Laser Bias current

LOSSL

Loss of Signal Seconds—Line

LP-BBE

Low-Order Path Background Block Error

LP-BBER

Low-Order Path Background Block Error Ratio

LP-EB

Low-Order Path Errored Block

LP-ES

Low-Order Path Errored Second

LP-ESA

Low-Order Path Errored Seconds - A

LP-ESB

Low-Order Path Errored Seconds - B

LP-ESR

Low-Order Path Errored Second Ratio

LP-FC

Low-Order Path Failure Count

LP-NPJC-DET

Low Order Negative Pointer Justification Count, Detected

LP-NPJC-GEN

Low Order Negative Pointer Justification Count, Generated

LP-PPJC-DET

Low Order Positive Pointer Justification Count, Detected

LP-PPJC-GEN

Low Order positive Pointer Justification Count, Generated

LP-SEP

A sequence of between 3 to 9 consecutive severely errored seconds (SES)

LP-SEPI

Low-Order Path Severely Errored Period Intensity

LP-SES

Low-Order Path Severely Errored Seconds

LP-UAS

Low-Order Path Unavailable Seconds

MS-PSC

Multiplex Section-Protection switch count

MS-PSD

Multiplex Section-Protection switch duration

NIOS

8B10B—Non Idle Ordered Sets

NPJC-PDET

Negative Pointer Justification Count, Path Detected

NPJC-PGEN

Negative Pointer Justification Count, Path Generated

OPR-AVG

Average Receive Power in 1/10 micro W

OPR-MAX

Maximum Receive Power in 1/10 micro W

OPR-MIN

Minimum Receive Power in 1/10 micro W

OPRN

Normalized Optical Receive Power for STM1-8

OPRN-MAX

Maximum value for OPRN

OPRN-MIN

Minimum value for OPRN

OPT-AVG

Average Transmit Power in 1/10 micro W

OPT-MAX

Maximum Transmit Power in 1/10 micro W

OPT-MIN

Minimum Transmit Power in 1/10 micro W

OPTN

Normalized value for Optical Power Transmitted for STM1-8 card

OPTN-MAX

Maximum value for OPTN

OPTN-MIN

Minimum value for OPTN

OPWR-AVG

Optical Power—Average Interval Value in 1/10th of dBm

OPWR-MAX

Optical Power—Maximum Interval Value in 1/10th of dBm

OPWR-MIN

Optical Power—Minimum Interval Value in 1/10th of dBm

PPJC-PDET

Positive Pointer Justification Count, Path Detected

PPJC-PGEN

Positive Pointer Justification Count, Path Generated

PSC

Protection Switching Count

PSC-R

Protection Switching Count—Ring

PSC-S

Protection Switching Count—Span

PSC-W

Protection Switching Count—Working

PSD

Protection Switching Duration

PSD-R

Protection Switching Duration—Ring

PSD-S

Protection Switching Duration—Span

PSD-W

Protection Switching Duration—Working

SASCPP

Severely Errored Framing/AIS Second—CP-Bit Path

SASP

Severely Errored Framing/AIS Seconds Path

SEFS

Severely Errored Framing Seconds

SESCPP

Severely Errored Second—CP-Bit Path

SESL

Severely Errored Second—Line

SESP

Severely Errored Second—Path

SES-PM

OTN—Severely Errored Second—Path

SESR

Severely Errored Second—Ratio

SESR-PM

OTN—Severely Errored Second Ratio—Path Monitor Point expressed as 1/10th of a percentage

SESR-SM

OTN—Severely Errored Second Ratio—Section Monitor Point expressed as 1/10th of a percentage

SESS

Severely Errored Second—Section

SES-SM

OTN—Severely Errored Second—Section Monitor Point

SESV

Severely Errored Second—VC Path

UASCPP

Unavailable Second—CP-Bit Path

UASL

Unavailable Second—Line

UASP

Unavailable Second—Path

UAS-PM

OTN—Unavailable Second—Path Monitor Point

UAS-SM

OTN—Unavailable Second—Section Monitor Point

UASV

Unavailable Second—VC Path

UNC-WORDS

FEC—Uncorrectable Words

VPC

Valid Packet Count

lSTM

Location associated with a particular command in reference to the entity identified by the AID

Parameter type is LOCATION—the location where the action is to take place

FEND

Action occurs on the Far End of the facility

NEND

Action occurs on the Near End of the facility

DIRN

Direction relative to the entity identified by the AID. Defaults to ALL, which means that the command initializes all of the registers irrespective of the PM direction

Parameter type is DIRECTION—transmit and receive directions

RCV

Receive direction only

TMPER

Accumulation time period for performance counters. A null value defaults to 15-MIN. Defaults to 15-MIN

Parameter type is TMPER—accumulation time period for the performance management center

1-DAY

Performance parameter accumulation interval length; every 24-hours. For SDH PM data only one day of history data is available. For RMON managed PM data seven days of history data are available.

1-HR

Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available.

1-MIN

Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available.

15-MIN

Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length.

RAW-DATA

Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs.


15.2  INIT-SYS

Initialize System

Usage Guidelines

This command initializes the specified card and its associated subsystem(s).


NoteThe SLOT-ALL AID and the list AID are not allowed in this command.

Only one level of reset is supported in this command.

It is important that the standby TCC2/TCC2P should be up and running fully standby before this command is sent on the active TCC2/TCC2P for a period of time. During this time, the system is vulnerable to traffic outages caused by timing disruptions or other causes.

The ONS 15310-CL supports the RESET parameters for the 15310-CL-CTX, CE-100T-8, and ML-100T-8 cards only.

The ONS 15600 does not support soft resets on pluggable IO modules (PIMs).

Before a card is hard reset, it must be in one of the following states: LOCKED-ENABLED, MAINTENANCE; LOCKED-ENABLED, DISABLED; LOCKED-DISABLED., MAINTENANCE; LOCKED-DISABLED, DISABLED.


Category

System

Security

Maintenance

Related Commands

ACT-USER

ALW-MSG-ALL

ALW-MSG-DBCHG

ALW-MSG-SECU

COPY-RFILE

DLT-TRAPTABLE

ED-DAT

ED-NE-GEN

ED-NE-PATH

ED-NE-SYNCN

ED-TRAPTABLE

ENT-TRAPTABLE

INH-MSG-ALL

INH-MSG-DBCHG

INH-MSG-SECU

REPT EVT FXFR

RTRV-HDR

RTRV-INV

RTRV-MAP-NETWORK

RTRV-NE-APC

RTRV-NE-GEN

RTRV-NE-IPMAP

RTRV-NE-PATH

RTRV-NE-SYNCN

RTRV-NE-WDMANS

RTRV-TOD

RTRV-TRAPTABLE

SET-TOD


Input Format

INIT-SYS:[<TID>]:<AID>:<CTAG>::<PH>[,<CMDMODE>];

Input Example

INIT-SYS:HOTWATER:SLOT-8:201::1,FRCD;

Input Parameters

Table 15-2 INIT-SYS Input Parameters 

Parameter and Values
Description

AID

Access identifier from the "25.1.10  EQPT" section on page 25-15

<PH>

The phase. 1=soft reset; 2=hard reset. PH is an integer. PH is a required parameter for the ONS 15600 and ONS 15310-CL

PH is supported on only the CE-100T-8 card on the ONS 15454.

CMDMDE

Command Mode. Allows the user to override safety checks. CMDMDE is not supported on the ONS15454 SDH. Defaults to NORM

Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

CMDMDE parameter is not supported on ONS 15310-CL and ONS 15454.

FRCD

Force the system to override a state in which the command would normally be denied

NORM

Execute the command normally. Do not override any conditions that could make the command fail