Cisco ONS 15327 Procedure Guide, Release 6.0
Chapter 1, Install Hardware
Downloads: This chapterpdf (PDF - 455.0KB) The complete bookPDF (PDF - 10.11MB) | Feedback

Install Hardware

Table Of Contents

Install Hardware

Before You Begin

Required Tools and Equipment

lncluded Materials

User-Supplied Materials

Tools Needed

Test Equipment

NTP-B1 Unpack and Inspect the ONS 15327 Shelf Assembly

NTP-B2 Install the Shelf Assembly

NTP-B216 Install the Mechanical Interface Cards

NTP-B6 Install the Power and Ground

NTP-B7 Install the Fan-Tray Assembly

NTP-B217 Install the XTC Cards

NTP-B218 Install the Optical and Ethernet Cards

NTP-B8 Install Wires to Alarm, Timing, LAN, and Craft Pin Connections

NTP-B220 Install the Electrical Cables

NTP-B221 Install Optical Cables

NTP-B219 Remove and Replace a Card

NTP-B115 Preprovision a Slot

NTP-B13 Perform the Shelf Installation Acceptance Test


Install Hardware


This chapter provides procedures for installing the Cisco ONS 15327 shelf, cards, and fiber-optic cable. To view a summary of the tools and equipment required for installation, see the "Required Tools and Equipment" section.

Before You Begin

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. B1 Unpack and Inspect the ONS 15327 Shelf Assembly—Complete this procedure before continuing with the "NTP-B2 Install the Shelf Assembly" procedure.

2. B2 Install the Shelf Assembly—Complete this procedure to install the shelf assembly in a rack before continuing with the "NTP-B216 Install the Mechanical Interface Cards" procedure.

3. B216 Install the Mechanical Interface Cards—Complete this procedure to install the mechanical interface cards (MICs) before continuing with the "NTP-B6 Install the Power and Ground" procedure.

4. B6 Install the Power and Ground—Complete this procedure before continuing with the "NTP-B7 Install the Fan-Tray Assembly" procedure.

5. B7 Install the Fan-Tray Assembly—Complete this procedure to install the fan-tray assembly in the shelf before continuing with the "NTP-B217 Install the XTC Cards" procedure.

6. B217 Install the XTC Cards—Complete this procedure to install the Cross-Connect Timing and Control (XTC) cards.

7. B218 Install the Optical and Ethernet Cards—As needed, complete this procedure to install optical and Ethernet cards.

8. B8 Install Wires to Alarm, Timing, LAN, and Craft Pin Connections—Complete this procedure to install cables for alarms, timing, and LAN connections.

9. B220 Install the Electrical Cables—Complete this procedure to connect and route cables that will carry electrical traffic.

10. B221 Install Optical Cables—Complete this procedure to connect and route cables that will carry optical traffic.

11. B219 Remove and Replace a Card—As needed, complete this procedure to remove and replace an ONS 15327 card.

12. B115 Preprovision a Slot—As needed, complete this procedure to preprovision any empty card slot with a card that will be installed later.

13. B13 Perform the Shelf Installation Acceptance Test—Complete this procedure to determine if you have correctly completed all other procedures in the chapter.


Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 148

Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location. Statement 37

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Note The ONS 15327 is designed to comply with Telcordia GR-1089-CORE Type 2 and Type 4. Install and operate the ONS 15327 only in environments that do not expose wiring or cabling to the outside plant. Acceptable applications include Central Office Environments (COEs), Electronic Equipment Enclosures (EEEs), Controlled Environment Vaults (CEVs), huts, and Customer Premise Environments (CPEs).



Note The ONS 15327 is intended for use with telecommunications equipment only.


Required Tools and Equipment

You will need the following tools and equipment to install and test the ONS 15327.

lncluded Materials

These materials are shipped with the ONS 15327. The number in parentheses provides the quantity of the item included in the package.

#12-24 x 1/2 pan-head Phillips mounting screws (4)

#10-32 x 3/8 pan-head Phillips power lug screws (2)

#12 AWG dual hole 5/8 in. spaced grounding lug

Electrostatic discharge (ESD) wrist strap with 1.8 m (6 ft) coil cable

Screw-lock power connector

Terminal-lug power connector

Terminal lugs (4)

Terminal lug screws (4)

Straight DS-1 cable

Tie-down bar (optional) (15327-TIE-BAR-19 for a 19-inch [483-mm] rack or 15327-TIE-BAR-23 for a 23-inch [584-mm] rack)

Cable storage tray and screws (4) (optional)

User-Supplied Materials

These materials and tools are required but are not supplied with the ONS 15327.

Equipment rack (22 inches [559 mm] total width for a 19-inch [483-mm] rack; 26 inches [660 mm] total width for a 23-inch [584-mm] rack)

Fuse panel

Copper power cable (from fuse and alarm panel to assembly), #12-16 AWG

The National Electrical Code recommends #12-14 AWG power cable.

Ground cable, #12 AWG stranded (minimum)

Alarm cable, CAT-5 terminated with RJ-45 for all alarm connections

Building Integrated Timing Supply (BITS) clock cable, #22 or #24 shielded AWG wire

Serial cable, DB-9 connectors

Single-mode SC fiber jumpers with UPC polish (55 dB or better) for OC-12 and OC-48 cards and fiber jumpers with LC connectors for the OC-3 card

Shielded ABAM cable terminated with Champ connectors for DS-1 ports with #22 or #24 AWG ground wire (optional)

Shielded coaxial cable terminated with BNC connectors for DS-3 ports

Tie wraps and/or lacing cord

Labels

Tools Needed

#2 Phillips screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Wire cutters

Wire strippers

Crimp tool

Needle-nose pliers (for bail locks on Champ connectors)

Test Equipment

Voltmeter

Power meter (for use with fiber optics only)

Bit error rate (BER) tester, DS-1 and DS-3


Note In this chapter, the terms "ONS 15327" and "shelf assembly" are used interchangeably. In the installation context, these terms have the same meaning. Otherwise, shelf assembly refers to the physical steel enclosure that holds cards and connects power, and ONS 15327 refers to the entire system, both hardware and software.


NTP-B1 Unpack and Inspect the ONS 15327 Shelf Assembly

Purpose

This procedure describes how to unpack the ONS 15327 and verify the contents.

Tools/Equipment

None

Prerequisite Procedures

None

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Step 1 Complete the "DLP-B1 Unpack and Verify the Shelf Assembly" task.

Step 2 Complete the "DLP-B2 Inspect the Shelf Assembly" task.

Step 3 Continue with the "NTP-B2 Install the Shelf Assembly" procedure.

Stop. You have completed this procedure.


NTP-B2 Install the Shelf Assembly

Purpose

This procedure describes how to reverse the mounting bracket and mount shelf assemblies in a rack.

Tools/Equipment

#2 Phillips screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Two set screws (48-1003-XX)

Prerequisite Procedures

B1 Unpack and Inspect the ONS 15327 Shelf Assembly

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning To prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around the ventilation openings.

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:
131°F (55°C). Statement 1047

Step 1 Complete the "DLP-B3 Reverse the Mounting Bracket to Fit a 19-Inch Rack" task if you need to convert from a 23-inch [584-mm] to a 19-inch [483-mm] rack.

Step 2 Complete the necessary rack mount task:

B5 Mount the ONS 15327 in a Rack

B7 Mount Multiple Shelf Assemblies in a Rack

Step 3 As needed, complete the "DLP-B329 Install the Tie-Down Bar" task.


Note You can also install a cable storage drawer in the ONS 15327 rack. This drawer provides room to store up to five feet (152.4 cm) of slack and can provide a diverse cable route for redundant power feeds and cables. See the "NTP-B223 Install the Fiber-Optic Cable Storage Drawer" procedure.


Step 4 Continue with the "NTP-B216 Install the Mechanical Interface Cards" procedure.

Stop. You have completed this procedure.


NTP-B216 Install the Mechanical Interface Cards

Purpose

This procedure installs the two mechanical interface cards (MICs) in Slots 7 and 8.

Tools/Equipment

None

Prerequisite Procedures

B2 Install the Shelf Assembly

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003

Step 1 Install MIC A in Slot 8:

a. Open the card ejectors.

b. Slide the card along the guide rails into the slot.

c. Close the ejectors.

d. Lock the cards into place by tightening the ejector locking screws.

The slots are keyed to ensure that cards are installed in the correct slots. Figure 1-1 shows the location and number of each slot.

Figure 1-1 ONS 15327 Slot Numbering

Step 2 If you require redundant power, more than 14 DS-1s, or you are using DS-3s, install MIC B in Slot 7.

Step 3 Continue with the "NTP-B6 Install the Power and Ground" procedure.

Stop. You have completed this procedure.


NTP-B6 Install the Power and Ground

Purpose

This procedure describes how to install power feeds and how to ground the ONS 15327.

Tools/Equipment

Ground cable, #12 AWG stranded (minimum)

Copper power cable (from fuse and alarm panel to assembly), #12-16 AWG (the National Electrical Code recommends #12-14 AWG power cable)

Prerequisite Procedures

B216 Install the Mechanical Interface Cards

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39

Warning Use copper conductors only. Statement 1025

Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022

Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

Caution Always use the supplied ESD wristband when working with a powered ONS 15327. Plug the wristband cable into the ESD jack located between the top high-speed and XTC slots.


Step 1 Verify that the proper fuse panel is installed (20-A fuse per shelf minimum). If not, install one according to manufacturer's instructions.

Step 2 Complete the "DLP-B30 Install Ferrites on Power Cabling" task.

Step 3 Complete the "DLP-B16 Connect the Office Ground to the ONS 15327" task.

Step 4 Complete the "DLP-B17 Connect Office Power to the ONS 15327 Shelf (Screw-Lock Power Connector)" task.

Step 5 Complete the "DLP-B18 Turn On and Verify Office Power" task.

Step 6 Continue with the "NTP-B7 Install the Fan-Tray Assembly" procedure.

Stop. You have completed this procedure.


NTP-B7 Install the Fan-Tray Assembly

Purpose

This procedure installs the fan-tray assembly.

Tools/Equipment

#2 Phillips screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

B2 Install the Shelf Assembly

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution Do not operate an ONS 15327 without a fan-tray air filter. A fan-tray air filter is mandatory.


Caution You must place the edge of the air filter flush against the front of the fan-tray assembly compartment when installing the fan-tray assembly on top of the air filter. Failure to do so could result in damage to the air filter, the fan-tray assembly, or both.


Caution Do not force a fan-tray assembly into place. Doing so can damage the connectors on the fan-tray assembly and/or the connectors on the back panel of the shelf assembly.


Step 1 If cables are installed, reposition them away from the fan-tray assembly slot.

Step 2 Slide the fan-tray assembly into the shelf assembly until the electrical plug at the rear of the tray plugs into the corresponding receptacle on the backplane.

Step 3 Secure the fan-tray assembly into the slot using the attached fastening screw.

Step 4 After power is supplied, confirm that the FAN STATUS LED on the front of the fan-tray assembly is on. This indicates that the fan-tray assembly is operating.

The FAN STATUS LED turns on only when an XTC card is installed.

Figure 1-2 shows the location of the fan-tray assembly.

Figure 1-2 Installing the Fan-Tray Assembly

Step 5 Continue with the "NTP-B217 Install the XTC Cards" procedure.

Stop. You have completed this procedure.


NTP-B217 Install the XTC Cards

Purpose

This procedure installs the XTC cards in Slots 5 and/or 6.

Tools/Equipment

None

Prerequisite Procedures

B7 Install the Fan-Tray Assembly

B216 Install the Mechanical Interface Cards

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

Retrieve or higher



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Note The ONS 15327 can run with a single XTC card with a second XTC card for redundancy or additional DS-1 and DS-3 interfaces. Because all traffic cards boot from the working XTC card, at least one XTC card must be installed in order to boot any traffic cards.



Note Be sure to install the correct XTC card. Downgrade procedures from XTC-28 to XTC-14 are not supported. Contact Cisco Technical Assistance Center (TAC) for more information or raise a request at http://www.cisco.com/cisco/web/support/index.html.



Step 1 Install an XTC card in Slot 6 (Figure 1-3):

a. Open the card ejectors.

b. Slide the card along the guide rails into the slot.

c. Close the ejectors.

d. Lock the cards into place by tightening the ejector locking screws.

Slot 6 is the working XTC card slot.

Figure 1-3 Installing an XTC (XTC 28-3)

Step 2 Verify that the red FAIL LED blinks for approximately 30 seconds.


Note Older versions of the XTC card have an amber FAIL LED.


Step 3 Verify that all LEDs blink once and turn off.

Step 4 After approximately 5 minutes, verify the ACT/STBY LED is green (active).


Caution A software upgrade might occur when you install an XTC. Wait until the software upgrade finishes before considering the XTC operational; this might take as long as 30 minutes.

Step 5 If required, install the second XTC card in Slot 5, which is the protect XTC card slot.

The active XTC card automatically copies its software version and database to the newly installed standby XTC card. This process may take 30 to 45 minutes. The FAIL LED and the ACT/STBY LED flash alternately every 30 to 45 seconds while the software from the active XTC card loads onto the newly installed XTC card.


Caution Do not remove the XTC card or disconnect power during the software download; doing so will corrupt the flash memory and disable the XTC card.

Step 6 After the LED boot sequence (Steps 3 and 4), verify that the ACT/STBY LED is amber. The amber LED indicates that the second XTC card is the standby XTC.

Step 7 Press the LAMP TEST button on the faceplate of each XTC and verify that all LEDs turn on while you press the button.

Step 8 When you log into Cisco Transport Controller (CTC), verify that the card appears in the correct slot on the node view screen and that the card is white on the CTC node view screen.

Step 9 Continue with the "NTP-B218 Install the Optical and Ethernet Cards" procedure.

Stop. You have completed this procedure.


NTP-B218 Install the Optical and Ethernet Cards

Purpose

This procedure installs the optical cards (OC-3, OC-12, and OC-48) and Ethernet cards (E10/100-4, G1000-2) in Slots 1 through 4.

Tools/Equipment

None

Prerequisite Procedures

B7 Install the Fan-Tray Assembly

B217 Install the XTC Cards

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

Retrieve or higher



Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards and faceplates are in place. Statement 156

Step 1 Install an Ethernet or optical card in Slots 1, 2, 3, or 4 (Figure 1-4):

a. Open the card ejectors.

b. Slide the card along the guide rails into the slot.

c. Close the ejectors.

d. Lock the cards into place by tightening the ejector locking screws.

Figure 1-4 Installing an Ethernet Card (E10/100-T)

Step 2 Verify the LED activity:

a. Verify that the red FAIL LED turns on for 20 to 30 seconds.

b. Verify that the red FAIL LED blinks for 30 to 45 seconds.

c. Verify that all LEDs blink once and turn off for 5 to 10 seconds.

d. Verify the ACT LED turns on.

Step 3 When you log into CTC, verify that the card appears in the correct slot on the CTC node view screen and appears white in node view.

Step 4 Repeat Steps 1 through 3 for each optical and Ethernet card you want to install.

Step 5 If you installed the G1000-2 card, complete the "DLP-B4 Install SFP Connectors on G1000-2 Cards" task.


Note If you need to remove an SFP, complete the "DLP-B6 Remove SFP Connectors from G1000-2 Cards" task.


Step 6 Continue with the "NTP-B8 Install Wires to Alarm, Timing, LAN, and Craft Pin Connections" procedure

Stop. You have completed this procedure.


NTP-B8 Install Wires to Alarm, Timing, LAN, and Craft Pin Connections

Purpose

This procedure installs alarm, timing, LAN, and craft wires.

Tools/Equipment

Alarm cable, CAT-5 terminated with RJ-45 for all alarm connections

#22 or #24 shielded AWG wire

Prerequisite Procedures

B216 Install the Mechanical Interface Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Complete the "DLP-B321 Install External Alarm Cables" task as necessary. Alarm wires are necessary to provision external alarm inputs and external alarm outputs.

Step 2 Complete the "DLP-B322 Install Timing Cables" task as needed. Timing wires are necessary to provision external timing.

Step 3 Complete the "DLP-B323 Install the Serial Cable for TL1 Craft Interface" task as needed. Craft wires are required to access TL1 using the craft interface.


Caution Always use the supplied ESD wristband when working with a powered ONS 15327. Plug the wristband cable into the ESD jack located between the top high-speed and XTC slots.

Step 4 Continue with the "NTP-B220 Install the Electrical Cables" procedure.

Stop. You have completed this procedure.


NTP-B220 Install the Electrical Cables

Purpose

This procedure describes how to install the electrical DS-1 (AMP Champ) and DS-3 (coaxial) cables. To carry electrical traffic on the ONS 15327, you must install electrical cable.

Tools/Equipment

Shielded coaxial cable terminated with BNC connectors for DS-3 ports

Shielded ABAM cable terminated with Champ connectors for DS-1 ports with #22 or #24 AWG ground wire (typically about 2 ft [61 cm] in length)

Prerequisite Procedures

B8 Install Wires to Alarm, Timing, LAN, and Craft Pin Connections

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Always use the supplied ESD wristband when working with a powered ONS 15327. Plug the wristband cable into the ESD jack located between the top traffic and XTC slots.


Step 1 Complete the "DLP-B324 Install DS-1 Champ Cables on a MIC" task as needed.

Step 2 Complete the "DLP-B325 Install Coaxial Cable with BNC Connectors" task as needed.

Step 3 Complete the "DLP-B326 Route Electrical Cables" task as needed.

Step 4 Continue with the "NTP-B221 Install Optical Cables" procedure.

Stop. You have completed this procedure.


NTP-B221 Install Optical Cables

Purpose

This procedure describes how to install fiber-optic cables on optical cards and small form-factor pluggable (SFP) interfaces.

Tools/Equipment

Single-mode SC fiber jumpers with UPC polish (55 dB or better) for OC-12 and OC-48 cards, and fiber jumpers with LC connectors for the OC-3 card

Fiber boot

Prerequisite Procedures

B218 Install the Optical and Ethernet Cards

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

Warning Laser radiation presents an invisible hazard, so personnel should avoid exposure to the laser beam. Personnel must be qualified in laser safety procedures and must use proper eye protection before working on this equipment. Statement 300

Caution Always use the supplied electrostatic discharge wristband when working with a powered ONS 15327. Plug the wristband cable into the ESD jack located between the top high-speed and XTC slots.


Note You can install the fiber immediately after installing the cards, or wait until you are ready to turn up the network. See Chapter 4 "Turn Up Network."



Note Inspect and clean all fiber connectors thoroughly. See the "NTP-B112 Clean Fiber Connectors" procedure for instructions. Dust particles can degrade performance. Put caps on any fiber connectors that are not used.



Note To install fiber-optic cables in the ONS 15327, a fiber cable with the corresponding connector type must be connected to the transmit and receive ports on the ONS 15327 cards.



Step 1 Test the optical receive levels for the installed cards and attenuate them accordingly. See Table 1-1 for the minimum and maximum levels.

Table 1-1 Optical Transmit and Receive Levels 

Card
Transmit
Receive
Minimum
Maximum
Minimum
Maximum

OC3 IR 4 1310

-15 dBm

-8 dBm

-28 dBm

-8 dBm

OC12 IR 1310

-15 dBm

-8 dBm

-29 dBm

-7 dBm

OC12 LR 1550

-3 dBm

+2 dBm

-29 dBm

-7 dBm

OC48 IR 1310

-5 dBm

0 dBm

-18 dBm

-0 dBm

OC48 LR 1550

-2 dBm

+3 dBm

-28 dBm

-8 dBm


Step 2 As needed, complete the "DLP-B327 Install Fiber-Optic Cables on the LGX Interface" task. Figure 1-5 shows the cable location.

Step 3 As needed, complete the "DLP-B42 Install Fiber-Optic Cables in a 1+1 Configuration" task.

Step 4 As needed, complete the "DLP-B43 Install Fiber-Optic Cables for Path Protection Configurations" task.

Step 5 As needed, complete the "DLP-B44 Install Fiber-Optic Cables for BLSR Configurations" task.

Figure 1-5 Installing a Fiber-Optic Cable

Step 6 As needed, complete the "DLP-B46 Route Fiber-Optic Cables" task.

Step 7 Continue with the "NTP-B13 Perform the Shelf Installation Acceptance Test" procedure.

Stop. You have completed this procedure.


NTP-B219 Remove and Replace a Card

Purpose

This procedure describes how to remove and replace cards in the ONS 15327 shelf.

Tools/Equipment

None

Prerequisite Procedures

B216 Install the Mechanical Interface Cards or

B217 Install the XTC Cards or

B218 Install the Optical and Ethernet Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

Provisioning or higher



Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003

Step 1 If you are not logged into CTC and you need to remove a card, continue with Step 3. When you log into CTC, troubleshoot the mismatched equipment (MEA) alarm with the Cisco ONS 15327 Troubleshooting Guide.

Step 2 If you are logged into CTC, complete one of the following:

Complete the "DLP-B320 Delete a Card" task and continue with Step 3.

Complete the "DLP-B247 Change an Optical Card" task to delete a card and replace it with a different optical card while maintaining existing provisioning.

Step 3 Physically remove the card:

a. Open the card latches/ejectors.

b. Use the latches/ejectors to pull the card forward and away from the shelf.

Step 4 Insert the new card using one of the following procedures as applicable:

B217 Install the XTC Cards

B218 Install the Optical and Ethernet Cards

Stop. You have completed this procedure.


NTP-B115 Preprovision a Slot

Purpose

This procedure describes how to preprovision a slot in the software before physical card installation.

Tools/Equipment

None

Prerequisite Procedures

Chapter 2 "Connect the PC and Log into the GUI"

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-B60 Log into CTC" task at the node where you want to preprovision the slot. If you are already logged in, continue with Step 2.

Step 2 Right-click the empty slot where you will later install a card.

Step 3 From the Add Card popup menu, choose the card type that will be installed.


Note When you preprovision a slot, the card appears purple in the CTC shelf display, rather than white when a card is physically in the slot.


Step 4 Continue with the "NTP-B221 Install Optical Cables" procedure.

Stop. You have completed this procedure.


NTP-B13 Perform the Shelf Installation Acceptance Test

Purpose

Use this procedure to perform a shelf installation acceptance test.

Tools/Equipment

Voltmeter

Prerequisite Procedures

Applicable procedures in Chapter 1 "Install Hardware"

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

Retrieve or higher



Step 1 Complete Table 1-2 by verifying that each procedure was completed.


Step 2 Check each wire and cable connection to make sure all cables are locked securely. If a wire or cable is loose, return to the appropriate procedure in this chapter to correct it.

Step 3 Complete the "DLP-B33 Measure Voltage" task.

Stop. You have completed this procedure.