Cisco ONS 15454 SDH Procedure Guide, Releases 4.1.1 and 4.5
About this Guide
Downloads: This chapterpdf (PDF - 179.0KB) The complete bookPDF (PDF - 10.53MB) | Feedback

About this Manual

Table Of Contents

About this Manual


About this Manual



Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.


This guide explains how to install, turn up, provision, and maintain a Cisco ONS 15454 SDH node and network. Two software releases were combined in this guide. Software Release 4.1 applies to all non-DWDM content. Software Release 4.5 applies only to DWDM content. Each DWDM-related chapter is clearly labeled.

Revision History

Date
Notes

03/30/2007

Revision History Table added for the first time

08/29/2007

Updated About this Manual chapter.

10/16/2007

Added a step to verify the pass through circuits in the Remove a SNCP Node procedure in the Add and Remove MS-SPRing and SNCP Nodes chapter.

02/18/2008

Modified a note in the "Install the Shelf Assembly" section in the Install the Shelf and FMECs" chapter.


The Cisco ONS 15454 SDH Troubleshooting Guide, R4.1.1 and R4.5 provides alarm clearing, general troubleshooting, and hardware replacement procedures.

For more detailed information regarding purpose and process, refer to the Cisco ONS 15454 SDH Reference Manual, R4.1.1 and R4.5.

Document Organization

This guide provides procedures for installation, turn up, provisioning and acceptance of ONS 15454 SDH nodes and ONS 15454 SDH designed networks. It is organized in a Cisco recommended work flow sequence for new installations, in addition to allowing easy access to procedures and tasks associated with adds, moves, and changes for existing installations.

Verification procedures are provided, where necessary, to allow contract vendors to complete the physical installation and then turn the site over to craft personnel for verification, provisioning, turn up and acceptance. The front matter of the book is present in the following sequence:

1. Title Page

2. Table of Contents

3. List of Figures

4. List of Tables

5. List of Procedures

6. List of Tasks

The information in the book follows a task oriented hierarchy using the elements described below.

Chapter (Director Level)

The guide is divided into logical work groups (chapters) that serve as director entry into the procedures. For example, if you are arriving on site after a contractor has installed the shelf hardware, proceed to Chapter 2, "Install Cards and Fiber-Optic Cable" and begin verifying installation and installing cards. You may proceed sequentially (recommended), or locate the work you want to perform from the list of procedures on the first page of every chapter (or turn to the front matter or index).

Non-Trouble Procedure (NTP)

Each NTP is a list of steps designed to accomplish a specific procedure. Follow the steps until the procedure is complete. If you need more detailed instructions, refer to the Detailed Level Procedure (DLP) specified in the procedure steps.


Note Throughout this guide, NTPs are referred to as "procedures" and DLPs are termed "tasks." Every reference to a procedure includes its NTP number, and every reference to a task includes its DLP number.


Detailed Level Procedure (DLP)

The DLP (task) supplies additional task details to support the NTP. The DLP lists numbered steps that lead you through completion of a task. Some steps require that equipment indications be checked for verification. When the proper response is not obtained, a trouble clearing reference is provided.

Document Conventions

This publication uses the following conventions:

Convention
Application

boldface

Commands and keywords in body text.

italic

Command input that is supplied by the user.

[     ]

Keywords or arguments that appear within square brackets are optional.

{ x | x | x }

A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one.

Ctrl

The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key.

screen font

Examples of information displayed on the screen.

boldface screen font

Examples of information that the user must enter.

<     >

Command parameters that must be replaced by module-specific codes.



Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.



Caution Means reader be careful. In this situation, the user might do something that could result in equipment damage or loss of data.

Warning


IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the translated safety warnings that accompanied this device.

Note:  SAVE THESE INSTRUCTIONS

Note:  This documentation is to be used in conjunction with the specific product installation guide that shipped with the product. Please refer to the Installation Guide, Configuration Guide, or other enclosed additional documentation for further details.



Obtaining Optical Networking Information

This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation and Submitting a Service Request section.

Where to Find Safety and Warning Information

For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.

Cisco Optical Networking Product Documentation CD-ROM

Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.