Cisco ONS 15454 SDH Procedure Guide, Release 4.0
Chapter 3, Connect the PC and Log into the GUI
Downloads: This chapterpdf (PDF - 482.0KB) The complete bookPDF (PDF - 9.09MB) | Feedback

Connect the PC and Log into the GUI

Table Of Contents

Connect the PC and Log into the GUI

Before You Begin

NTP-D21 Set Up Computer for CTC

DLP-D47 Run the CTC Installation Wizard for Windows

DLP-D48 Run the CTC Installation Wizard for UNIX

DLP-D49 Set Up the Java Runtime Environment for UNIX

NTP-D22 Set Up CTC Computer to Connect to the ONS 15454 SDH

DLP-D50 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH on the Same Subnet Using Static IP Addresses

DLP-D51 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using DHCP

DLP-D52 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using Automatic Host Detection

DLP-D53 Set Up a Solaris Workstation for a Craft Connection to an ONS 15454 SDH

DLP-D55 Set Up a Computer for a Corporate LAN Connection

DLP-D56 Disable Proxy Service Using Internet Explorer (Windows)

DLP-D57 Disable Proxy Service Using Netscape (Windows and UNIX)

DLP-D58 Provision Remote Access to the ONS 15454 SDH

NTP-D23 Log into the ONS 15454 SDH GUI

DLP-D59 Connect Computer to the ONS 15454 SDH

DLP-D60 Log into CTC

DLP-D61 Create Login Node Groups

DLP-D62 Add a Node to the Current Session or Login Group


Connect the PC and Log into the GUI


This chapter explains how to connect PCs and workstations to the Cisco ONS 15454 SDH and how to log into Cisco Transport Controller (CTC) software, the Cisco ONS 15454 SDH Operation, Administration, Maintenance and Provisioning (OAM&P) user interface.

Before You Begin

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. 21 Set Up Computer for CTC—Complete this procedure if your PC or workstation has never been connected to an ONS 15454 SDH.

2. 22 Set Up CTC Computer to Connect to the ONS 15454 SDH—After your PC or workstation is set up for CTC, complete this procedure to set up your computer to connect to the ONS 15454 SDH.

3. 23 Log into the ONS 15454 SDH GUI—Complete this procedure to log into CTC.

NTP-D21 Set Up Computer for CTC

Purpose

This procedure configures your PC or UNIX workstation to run Cisco Transport Controller (CTC).

Tools/Equipment

Cisco ONS 15454 SDH Release 4.0 software or documentation CD

Prerequisite Procedures

None

Required/As Needed

Required

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 If your computer is a Windows PC, complete the "DLP-D47 Run the CTC Installation Wizard for Windows" task, then go to Step 4.

Step 2 If your computer is a UNIX workstation, complete the "DLP-D48 Run the CTC Installation Wizard for UNIX" task.

Step 3 If your computer is a UNIX workstation and you installed the Java Runtime Environment (JRE) in Step 2, complete the "DLP-D49 Set Up the Java Runtime Environment for UNIX" task.

Step 4 When your PC or workstation is set up, complete the "22 Set Up CTC Computer to Connect to the ONS 15454 SDH" procedure.

Stop. You have completed this procedure.


DLP-D47 Run the CTC Installation Wizard for Windows

Purpose

This task installs CTC online help as well as programs required to run CTC on Windows PCs: Netscape 4.73 and JRE 1.3.1_02. It also modifies the JRE policy file so CTC files can be downloaded to your computer when you connect to an ONS 15454 SDH.

Tools/Equipment

Cisco ONS 15454 SDH Release 4.0 software or documentation CD

Prerequisite Procedures

None

Required/As Needed

This task is required if any one of the following is true:

Netscape Release 4.73 or later or Internet Explorer Release 4.0 (service pack 2) or later is not installed.

JRE 1.3.1_02 is not installed.

CTC online help is not installed and is needed.

The JRE java.policy file has not been modified for CTC.

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 Verify that your computer has the following:

Processor—Pentium II, 300 Mhz or faster.

RAM—128 MB.

Hard drive—2 GB is recommended. 50 MB of space must be available.

Operating System—Windows 95, Windows 98, Windows NT 4.0, Windows 2000, or Windows XP. If your operating system is Windows NT 4.0, verify that Service Pack 5 or later is installed: from the Start menu, choose Programs > Administrative Tools > Windows NT Diagnostics and check the service pack on the Version tab of the Windows NT Diagnostics dialog box. If Service Pack 5 or later is not installed, do not continue. Install Service Pack 5 following the computer upgrade procedures for your site.


Note Processor and RAM requirements are guidelines. CTC performance is faster if your computer has a faster processor and more RAM. Refer to the Cisco ONS 15454 SDH Reference Manual for computer requirements needed for small, medium, and large ONS 15454 SDH networks.


Step 2 Insert the Cisco ONS 15454 SDH Release 4.0 software or documentation CD into your computer CD drive. The installation program begins running automatically. If it does not start, navigate to your computer's CD directory and double-click setup.exe.

The Cisco Transport Controller Installation Wizard displays the components that will be installed on your computer (Figure 3-1).

Figure 3-1 Cisco Transport Controller Installation Wizard

Step 3 Click Next.

Step 4 Choose Typical to install all the components shown in Figure 3-1, or choose Custom if you only want to install some of the components.

Step 5 Click Next.

Step 6 If you selected Custom in Step 4, select the CTC components you want to install and click Next. If you selected Typical, skip this step and proceed to Step 7.

Step 7 The directory where the installation wizard will install CTC online help is displayed. The default is C:\Program Files\Cisco\CTC\Documentation.

a. If you do not want to change the directory, skip this step and proceed to Step 8.

b. If you want to change the CTC online help directory, type the new directory path in the Directory Name field, or click Browse to navigate to the directory.

Step 8 Click Next.

Step 9 Review the components that will be installed. If you want to change them, click Back. If you have an active CTC session (for example, you are monitoring alarms or conditions), close CTC before going to Step 10.

Step 10 Click Next.

An Installation Issues dialog box is displayed.

Step 11 Review the issues, then click OK. The InstallShield program begins the Netscape Communicator 4.73 Setup program.

Step 12 Complete the Netscape installation:

a. On the Netscape Communicator 4.73 Setup dialog box, click Next.

b. On the Software License Agreement dialog box, click Yes.

c. On the Setup Type dialog box, click Typical, then click Next.


Note If the Netscape installation hangs when installing RealPlayer G2, restart the CTC installation by pressing Ctrl-Alt-Del. In the Windows Security dialog box, click Task Manager. In the Windows Task Manager dialog box, click Cisco Transport Controller Installation Wizard, then click the End Task button. Click Yes in the confirmation dialog box. Navigate to the drive containing the CTC CD and double-click CTC.exe. Repeat Steps 1 to 11. At Step 12, Step c, click Custom, then click Next. At the next panel, deselect RealPlayer. Continue with Step d.


d. On the Netscape Desktop Preferences Options dialog box, check the boxes that apply according to your site requirements (these options do not affect CTC operation), then click Next.

e. On the Select Program Folder dialog box, click Next.

f. On the Start Copying Files dialog box, click Install. The program begins the Netscape installation.

g. On the Question dialog box, click No.

h. On the Information dialog box, click OK.

i. On the Restarting Windows dialog box, click No, I will restart later, then click OK.

Step 13 Close the Netscape Communicator directory window to display the Cisco Transport Controller Installation Wizard dialog box.

Step 14 On the CTC Installation Wizard dialog box, click Next. The Java 2 runtime environment installation begins.

Step 15 Complete the JRE installation:

a. On the Software License Agreement dialog box, click Yes.

b. On the Choose Destination Location dialog box, click Next.

c. On the Select Browser dialog box, click the Microsoft Internet Explorer and Netscape 6 check boxes, then click Next.

When JRE installation is complete, the Cisco Transport Controller Installation Wizard dialog box is displayed.

Step 16 Click Next. The CTC online help is installed. When installed, the policy file selection is displayed.

Step 17 Choose the JRE policy file to modify:

Choose User Policy File (default) to modify the policy file that applies only to your user profile. This file is not overwritten if you upgrade or reinstall the JRE. If you are the only user who will access an ONS 15454 SDH from the PC you are setting up, choose this option.

Choose System Policy File to modify the system JRE policy file. This policy file applies to all computer users. If more than one individual will use this computer to access the ONS 15454 SDH, choose this option. However, if you reinstall or upgrade the JRE, the system policy file is overwritten and you must run the CTC Installation Setup program again to modify it.

Step 18 Click Next.

Step 19 If you selected System Policy File in Step 17, complete the following steps. If you selected User Policy File, go to Step 20.

a. The System Policy File Update dialog box displays the default policy file location (C:\Program Files\JavaSoft\jre). If you installed the JRE in a different location, enter the new path in the Directory Name field. After entering the path, or if the default path is correct, click OK.

b. Click OK in the confirmation dialog box.

Step 20 Click Finish.

Step 21 Return to your originating procedure (NTP).


DLP-D48 Run the CTC Installation Wizard for UNIX

Purpose

This task installs CTC online help and programs required to run CTC on Solaris workstations: Netscape 4.76 and JRE 1.3.1_02. It also modifies the JRE policy file to allow CTC files to be downloaded to your computer after you connect to an ONS 15454 SDH.

Tools/Equipment

Cisco ONS 15454 SDH Release 4.0 software or documentation CD

Prerequisite Procedures

None

Required/As Needed

Required if any of the following are true:

Netscape Release 4.76 is not installed.

JRE 1.3.1_02 is not installed.

CTC online help is not installed and is needed.

The JRE java.policy file has not been modified for CTC.

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 Verify that your computer has the following:

RAM—128 MB.

Hard drive—Verify that 50 MB of space is available.

Operating System—Solaris 2.5.x or 2.6.x.


Note These requirements are guidelines. CTC performance is faster if your computer has a faster processor and more RAM. Refer to the Cisco ONS 15454 SDH Reference Manual for computer requirements needed for small, medium, and large ONS 15454 SDH networks.


Step 2 Change the directory, type:

cd /cdrom/cdrom0/

Step 3 From the techdoc454 CD directory, type:

./setup.bat

The Cisco Transport Controller Installation Wizard displays the components that will be installed on your computer (Figure 3-1):

Netscape Communicator 4.76.

Java Runtime Environment 1.3.1_02.

CTC Online Help.

Modify Policy File—The JRE java.policy file is modified to enable CTC to download files needed to run the Cisco Transport Controller when you connect to an ONS 15454 SDH.

Step 4 Click Next.

Step 5 Choose Typical to install all components, or choose Custom if you want to choose particular components to install.

Step 6 Click Next.

Step 7 If you selected the Custom in Step 5, choose the CTC components you want to install and click Next. If you selected Typical, proceed to Step 8.

Step 8 The directory where the installation wizard will install CTC online help is displayed. The default is C:\Program Files\Cisco\CTC\Documentation. If you want to change the CTC online help directory, type the new directory path in the Directory Name field, or click Browse to navigate to the directory.

Step 9 Click Next.

Step 10 Review the components that will be installed. If you want to change them, click Back. If CTC is running (for example, you are reinstalling components) close CTC before going to the next step.

Step 11 Click Next. The InstallShield program begins the Netscape Communicator 4.76 Setup program.

Step 12 Complete the Netscape installation:

a. On the Netscape Communicator 4.76 Setup dialog box, click Next.

b. On the Software License Agreement dialog box, click Yes.

c. On the Setup Type dialog box, click Typical.

d. On the Netscape Desktop Preferences dialog box, check the boxes that apply, then click Next.

e. On the Program Folder dialog box, click Next.

f. On the Start Copying Files dialog box, click Install. The program begins the Netscape installation.

g. On the Question dialog box, click No.

Step 13 On the Cisco Transport Controller Installation Wizard dialog box, click Next. The Java 2 runtime environment installation begins.

Step 14 Complete the JRE installation:

a. On the Software License Agreement dialog box, click Yes.

b. On the Choose Destination Location dialog box, click Next.

c. On the Select Browser dialog box, click the Netscape 6 check box, then click Next.

When JRE installation is complete, the Cisco Transport Controller Installation Wizard dialog box is displayed.

Step 15 Click Next. The CTC online help is installed. When installed, the policy file selection is displayed.

Step 16 Choose the JRE policy file to modify:

Choose User Policy File (default) to modify a policy file that applies only to your user profile. This file is not overwritten if you upgrade or reinstall the JRE. If you are the only computer user who will access an ONS 15454 SDH, choose this option.

Choose System Policy File to modify the system JRE policy file. This policy file applies to all computer users. If more than one individual will use this computer to access the ONS 15454 SDH, choose this option. However, if you reinstall or upgrade the JRE, the system policy file is overwritten and you must run the CTC Installation Setup program again to modify it.

Step 17 Click Next, then click Finish.


Note Be sure to record the names of the directories you choose for Netscape, JRE, and the online documentation.


Step 18 Return to your originating procedure (NTP).


DLP-D49 Set Up the Java Runtime Environment for UNIX

Purpose

Use this task to set up the JRE for UNIX workstations.

Tools/Equipment

None

Prerequisite Procedures

48 Run the CTC Installation Wizard for UNIX

Required/As Needed

Required if you installed the JRE during the CTC installation

Onsite/Remote

Onsite or remote

Security Level

None



Note The JRE might require certain patches to run properly. The patch tar file can be found in the JRE/Solaris directory on the CD. Please read the JRE/Solaris/Solaris.txt file for more information. In addition to installing any needed patches, set up the JRE for use with Cisco Transport Controller on your UNIX system.



Note CTC requires that the location of xterm is also in your path. If you have moved xterm from its default location, /usr/openwin/bin, you must change all occurrences of /usr/openwin/bin in the following procedures to reflect the actual path where xterm exists on your system.



Step 1 Set up the environment variable:

a. If you are using the csh shell, edit the .cshrc file in your home directory by appending the file with the lines:

setenv JRE JRE-path
setenv NETSCAPE Netscape-path
setenv NPX_PLUGIN_PATH $JRE/j2re1_3_1_02/plugin/sparc/ns4
set path = ( /usr/openwin/bin $NETSCAPE $path )

b. If you are using the ksh or bash shell, edit the .profile file in your home directory by appending the file with the lines:

JRE=JRE-path
NETSCAPE=Netscape-path
NPX_PLUGIN_PATH=$JRE/j2re1_3_1_02/plugin/sparc/ns4 
PATH=/usr/openwin/bin:$NETSCAPE:$PATH 
export JRE NPX_PLUGIN_PATH PATH

Step 2 Set the JRE reference:

a. Run the Control Panel by typing:

JRE-path/j2re1_3_0_02/bin/ControlPanel

b. Click the Advanced tab.

c. From the combo box, select JRE-path/j2re1_3_1_02. If the JRE is not found, select other and enter the following in the Path text box:

JRE-path/j2re1_3_1_02

d. Click Apply.


Note If you are running multiple shells, before your new environment variable can be set you might need to invoke the same shell for which you changed the initialization file (for example, if you added the environment variable to the .cshrc file, you must run your browser under the csh shell.


Step 3 Return to your originating procedure (NTP).


NTP-D22 Set Up CTC Computer to Connect to the ONS 15454 SDH

Purpose

This procedure configures a PC running Windows or a Solaris workstation to connect to the ONS 15454 SDH.

Tools/Equipment

Depends on connection type

Prerequisite Procedures

21 Set Up Computer for CTC

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 From Table 3-1, select the ONS 15454 SDH connection type that you want to set up for your computer.


Note For initial shelf turn up, you should connect your PC directly to the LAN port on the TCC2 card of the ONS 15454 SDH.


Table 3-1 ONS 15454 SDH Connection Methods

Method
Description
Requirements

Local craft

Refers to onsite network connections between the CTC computer and the ONS 15454 SDH through one of the following connections:

The RJ-45 (LAN) port on the TCC2 card

The RJ-45 jack on the MIC-C/T/P FMEC

A hub or switch to which the ONS 15454 SDH is connected

If you do not use Dynamic Host Configuration Protocol (DHCP), you must change the computer IP address, subnet mask, and default router, or use automatic host detection.

Corporate LAN

Refers to a connection to the ONS 15454 SDH through a corporate or network operations center (NOC) LAN.

The ONS 15454 SDH must be provisioned for LAN connectivity, including IP address, subnet mask, default gateway.

The ONS 15454 SDH must be physically connected to the corporate LAN.

The CTC computer must be connected to the corporate LAN that has connectivity to the ONS 15454 SDH.

Remote

Refers to a connection made to the ONS 15454 SDH using a modem.

A modem must be connected to the ONS 15454 SDH.

The modem must be provisioned for ONS 15454 SDH. To run CTC, the modem must be provisioned for Ethernet access.


Step 2 If you need to set up your computer for corporate LAN access, complete the "DLP-D55 Set Up a Computer for a Corporate LAN Connection" task. If not, proceed to the next step.

Step 3 If you need to set up the computer for remote access, complete the "DLP-D58 Provision Remote Access to the ONS 15454 SDH" task. If not, proceed to the next step.

Step 4 If you need to set up your computer for local craft connections, choose a task from Table 3-2.

Table 3-2 ONS 15454 SDH Craft Connection Options

Local Craft Connection Task
Description

52 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using Automatic Host Detection

Complete this task if:

You will connect to ONS 15454 SDHs at different locations and times and do not wish to reconfigure your PC IP settings each time.

You do not need to access or use non-ONS 15454 SDH applications such as ping and trace route.

You will connect to the ONS 15454 SDH's TCC2 card Ethernet port or RJ-45 jack on the MIC-C/T/P FMEC either directly or through a hub.

50 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH on the Same Subnet Using Static IP Addresses

Complete one of these tasks if:

You are connecting from a Windows PC.

You will connect to one ONS 15454 SDH; if you will connect to multiple ONS 15454 SDHs, you might need to configure your computer's IP settings each time you connect to an ONS 15454 SDH.

You need to access non-ONS 15454 SDH applications such as ping and trace route.

53 Set Up a Solaris Workstation for a Craft Connection to an ONS 15454 SDH

Complete one of these tasks if:

You are connecting from a Solaris Workstation.

You will connect to one ONS 15454 SDH; if you will connect to multiple ONS 15454 SDHs, you might need to configure your computer's IP settings each time you connect to an ONS 15454 SDH.

You need to access non-ONS 15454 SDH applications such as ping and trace route.

51 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using DHCP

Complete this task if:

The CTC computer is provisioned for DHCP.

The ONS 15454 SDH has DHCP forwarding enabled and is connected to a DHCP server.


Stop. You have completed this procedure.


DLP-D50 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH on the Same Subnet Using Static IP Addresses

Purpose

Use this task to set up your computer for a local craft connection to the ONS 15454 SDH when:

You will connect to one ONS 15454 SDH; if you will connect to multiple ONS 15454 SDHs, you might need to reconfigure your computer's IP settings each time you connect to an ONS 15454 SDH.

You need to use non-ONS 15454 SDH applications such as ping and trace route.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Verify the operating system that is installed on your computer:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel window, double-click the System icon.

c. On the General tab of the System Settings window, verify that the Windows operating system is one of the following: Windows 95, Windows 98, Windows NT 4.0, Windows 2000, or Windows XP.

Step 2 If you have Windows 95 or 98 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel dialog box, click the Network icon.

c. On the Network dialog box select TCP/IP for your PC Ethernet card, then click Properties.

d. On the TCP/IP Properties dialog box, click the DNS Configuration tab and choose Disable DNS.

e. Click the WINS Configuration tab and choose Disable WINS Resolution.

f. Click the IP Address tab.

g. On the IP Address window, click Specify an IP address.

h. On the IP Address field, enter an IP address that is identical to the ONS 15454 SDH IP address shown on the ONS 15454 SDH LCD except for the last three digits. The last three digits must be between 1 and 254. This IP address can be displayed on the LCD. Software R4.0 allows suppressing the LCD IP address display.

i. On the Subnet Mask field, type the same subnet mask as the ONS 15454. The default is 255.255.255.0 (24 bit).

j. Click OK.

k. On the TCP/IP dialog box, click the Gateway tab.

l. On the New Gateway field, type the ONS 15454 SDH IP address. Click Add.

m. Verify that the IP address appears in the Installed Gateways field, then click OK.

n. When the prompt to restart your PC appears, click Yes.

Step 3 If you have Windows NT 4.0 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel dialog box, click the Network icon.

c. On the Network dialog box click the Protocols tab, choose TCP/IP Protocol, then click Properties.

d. Click the IP Address tab.

e. On the IP Address window, click Specify an IP address.

f. On the IP Address field, enter an IP address that is identical to the ONS 15454 SDH IP address shown on the ONS 15454 SDH LCD except for the last three digits. The last three digits must be between 1 and 254.

g. On the Subnet Mask field, type 255.255.255.0.

h. Click the Advanced button.

i. Under the Gateways List, click Add. The TCP/IP Gateway Address dialog box is displayed.

j. Type the ONS 15454 SDH IP address in the Gateway Address field.

k. Click Add.

l. Click OK.

m. Click Apply.

n. In some cases, Windows NT 4.0 prompts you to reboot your PC. If you receive this prompt, click Yes.

Step 4 If you have Windows 2000 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Network and Dial-up Connections > Local Area Connection.

b. On the Local Area Connection Status dialog box, click Properties.

c. On the General tab, choose Internet Protocol (TCP/IP), then click Properties.

d. Click Use the following IP address.

e. On the IP Address field, enter an IP address that is identical to the ONS 15454 SDH IP address shown on the ONS 15454 SDH LCD except for the last three digits. The last three digits must be between 1 and 254.

f. On the Subnet Mask field, type 255.255.255.0.

g. On the Default Gateway field, type the ONS 15454 SDH IP address.

h. Click OK.

i. On the Local Area Connection Properties dialog box, click OK.

j. On the Local Area Connection Status dialog box, click Close.

Step 5 If you have Windows XP installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Control Panel > Network Connections.


Note If the Network Connections menu is not available, click Switch to Classic View.


b. From the Network Connections dialog box, click the Local Area Connection icon.

c. From the Local Area Connection Properties dialog box, choose Internet Protocol (TCP/IP), then click Properties.

d. On the IP Address field, enter an IP address that is identical to the ONS 15454 SDH IP address shown on the ONS 15454 SDH LCD except for the last three digits. The last three digits must be between 1 and 254.

e. On the Subnet Mask field, type 255.255.255.0.

f. On the Default Gateway field, type the ONS 15454 SDH IP address.

g. Click OK.

h. On the Local Area Connection Properties dialog box, click OK.

i. On the Local Area Connection Status dialog box, click Close.

Step 6 Return to your originating procedure (NTP).


DLP-D51 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using DHCP

Purpose

Use this task to set up your computer for craft connection to the ONS 15454 SDH using DHCP.

Tools/Equipment

Straight-through (Category 5) LAN cable

Prerequisite Procedures

21 Set Up Computer for CTC

NTP-D169 Set Up CTC Network Access, page 4-7

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution You cannot connect to the ONS 15454 SDH if DHCP forwarding is not enabled on the ONS 15454 SDH or the ONS 15454 SDH is not connected to a DHCP server. By default, DHCP forwarding is not enabled. If you are connecting to an ONS 15454 SDH to perform initial shelf turnup, complete the "DLP-D50 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH on the Same Subnet Using Static IP Addresses" task or the "DLP-D52 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using Automatic Host Detection" task.


Step 1 Verify the operating system that is installed on your computer:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel window, double-click the System icon.

c. On the General tab of the System Settings window, verify that the Windows operating system is one of the following: Windows 95, Windows 98, Windows NT 4.0, Windows 2000, or Windows XP.

Step 2 If you have Windows 95 or 98 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel dialog box, click the Network icon.

c. On the Network dialog box select TCP/IP for your PC Ethernet card, then click Properties.

d. On the TCP/IP Properties dialog box, click the DNS Configuration tab and choose Disable DNS.

e. Click the WINS Configuration tab and choose Disable WINS Resolution.

f. Click the IP Address tab.

g. On the IP Address window, click Obtain an IP address from a DHCP Server.

h. Click OK.

i. When the prompt to restart your PC appears, click Yes.

Step 3 If you have Windows NT 4.0 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel dialog box, click the Network icon.

c. On the Network dialog box click the Protocols tab, choose TCP/IP Protocol, then click Properties.

d. Click the IP Address tab.

e. On the IP Address window, click Obtain an IP address from a DHCP Server.

f. Click OK.

g. Click Apply.

h. If Windows prompts you to restart your PC, click Yes.

Step 4 If you have Windows 2000 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Network and Dial-up Connections > Local Area Connection.

b. On the Local Area Connection Status dialog box, click Properties.

c. On the General tab, choose Internet Protocol (TCP/IP), then click Properties.

d. Click Obtain an IP address from a DHCP Server.

e. Click OK.

f. On the Local Area Connection Properties dialog box, click OK.

g. On the Local Area Connection Status dialog box, click Close.

Step 5 If you have Windows XP installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Control Panel > Network Connections.


Note If the Network Connections menu is not available, click Switch to Classic View.


b. On the Network Connections dialog box, click Local Area Connection.

c. On the Local Area Connection Status dialog box, click Properties.

d. On the General tab, choose Internet Protocol (TCP/IP), then click Properties.

e. Click Obtain an IP address automatically.

f. Click OK.

g. On the Local Area Connection Properties dialog box, click OK.

h. On the Local Area Connection Status dialog box, click Close.

Step 6 Return to your originating procedure (NTP).


DLP-D52 Set Up a Windows PC for Craft Connection to an ONS 15454 SDH Using Automatic Host Detection

Purpose

Use this task to set up your computer for local craft connection to the ONS 15454 SDH when:

You will connect to the ONS 15454 SDH's Ethernet port or the RJ-45 jack on the MIC-C/T/P FMEC either directly or through a hub.

You will connect to multiple ONS 15454 SDHs and do not want to reconfigure your IP address each time.

You do not need to access non-ONS 15454 SDH applications such as ping and trace route.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Note If you are using automatic host detection and you disconnect a straight-through (Category 5) LAN cable from one node and connect it to another node, you must close CTC and relaunch it to reconnect to the proxy server and communicate with the new node.



Step 1 Verify the operating system that is installed on your computer:

a. From the Windows Start menu, choose Settings > Control Panel.


Note In Windows XP, you can select Control Panel directly from the Start menu. Make sure you are in Classic View before continuing with this procedure.


b. On the Control Panel window, double-click the System icon.

c. On the General tab of the System Settings window, verify that the Windows operating system is one of the following: Windows 95, Windows 98, Windows NT 4.0, Windows 2000, or Windows XP.

Step 2 If you have Windows 95 or 98 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel dialog box, click the Network icon.

c. On the Network dialog box select TCP/IP for your PC Ethernet card, then click Properties.

d. On the TCP/IP Properties dialog box, click the DNS Configuration tab and choose Disable DNS.

e. Click the WINS Configuration tab and choose Disable WINS Resolution.

f. Click the IP Address tab.

g. On the IP Address window, click Specify an IP address.

h. On the IP Address field, enter any legitimate IP address other than the node IP address as indicated on the LCD of the ONS 15454.

i. On the Subnet Mask field, type the same subnet mask as the ONS 15454. The default is 255.255.255.0 (24 bit).

j. Click OK.

k. On the TCP/IP dialog box, click the Gateway tab.

l. On the New Gateway field, type the address entered in Step f. Click Add.

m. Verify that the IP address appears in the Installed Gateways field, then click OK.

n. When the prompt to restart your PC appears, click Yes.

Step 3 If you have Windows NT 4.0 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Control Panel.

b. On the Control Panel dialog box, click the Network icon.

c. On the Network dialog box click the Protocols tab, choose TCP/IP Protocol, then click Properties.

d. Click the IP Address tab.

e. On the IP Address window, click Specify an IP address.

f. On the IP Address field, enter any legitimate IP address other than the node IP address as indicated on the LCD of the ONS 15454.

g. On the Subnet Mask field, type the same subnet mask as the ONS 15454. The default is 255.255.255.0 (24 bit).

h. Click the Advanced button.

i. Under the Gateways List, click Add. The TCP/IP Gateway Address dialog box is displayed.

j. Type the IP address entered in Step f in the Gateway Address field.

k. Click Add.

l. Click OK.

m. Click Apply.

n. Reboot your PC.

Step 4 If you have Windows 2000 installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Settings > Network and Dial-up Connections > Local Area Connection.

b. On the Local Area Connection Status dialog box, click Properties.

c. On the General tab, choose Internet Protocol (TCP/IP), then click Properties.

d. Click Use the following IP address.

e. On the IP Address field, enter any legitimate IP address other than the node IP address as indicated on the LCD of the ONS 15454.

f. On the Subnet Mask field, type the same subnet mask as the ONS 15454. The default is 255.255.255.0 (24 bit).

g. Type the IP address entered in Step e in the Gateway Address field.

h. Click OK.

i. On the Local Area Connection Properties dialog box, click OK.

j. On the Local Area Connection Status dialog box, click Close.

Step 5 If you have Windows XP installed on your PC, complete the following steps:

a. From the Windows Start menu, choose Control Panel > Network Connections.


Note If the Network Connections menu is not available, click Switch to Classic View.


b. From the Network Connections dialog box, click the Local Area Connection icon.

c. From the Local Area Connection Properties dialog box, choose Internet Protocol (TCP/IP), then click Properties.

d. On the IP Address field, enter any legitimate IP address other than the node IP address as indicated on the LCD of the ONS 15454.

e. On the Subnet Mask field, type the same subnet mask as the ONS 15454. The default is 255.255.255.0 (24 bit).

f. Type the IP address entered in Step d in the Gateway Address field.

g. Click OK.

h. On the Local Area Connection Properties dialog box, click OK.

i. On the Local Area Connection Status dialog box, click Close.

Step 6 Return to your originating procedure (NTP).


DLP-D53 Set Up a Solaris Workstation for a Craft Connection to an ONS 15454 SDH

Purpose

Use this task to set up a Solaris workstation for a craft connection to the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Log into the workstation as the root user.

Step 2 Check to see if the interface is plumbed by typing:

# ifconfig <device>

For example: # ifconfig hme1

a. If the interface is plumbed, a message similar to the following appears:

hme1:flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4>mtu 1500 index 2 inet 0.0.0.0 netmask 0

Go to Step 4.

b. If the interface is not plumbed, a message similar to the following appears:

ifconfig: status: SIOCGLIFFLAGS: hme1: no such interface. 

Plumb the interface by typing:

# if config device plumb

For example:

# ifconfig hme1 plumb

Step 3 Configure the IP address on the interface by typing:

# ifconfig interface ip-address netmask netmask up

For example:

# ifconfig hme0 10.20.30.40 netmask 255.255.255.0 up


Note Enter an IP address that is identical to the ONS 15454 SDH IP address except for the last three digits. The last three digits must be between 1 and 254.


Step 4 On the Subnet Mask field, type 255.255.255.0. Skip this step if you checked Craft Access Only at Provisioning > Network > General > Gateway Settings.

Step 5 Test the connection:

a. Start Netscape Navigator.

b. Enter the Cisco ONS 15454 SDH IP address in the web address (URL) field. If the connection is established, a Java Console window, CTC caching messages, and the Cisco Transport Controller Login dialog box appear. If this occurs, go to Step 2 of the "DLP-D60 Log into CTC" task to complete the login. If the Login dialog box does not appear, complete Steps c to d.

c. At the prompt, type:

ping ONS-15454-SDH-IP-address

For example, to connect to an ONS 15454 SDH with default IP address 192.168.1.1, type:

ping 192.168.1.1

If your workstation is connected to the ONS 15454 SDH, the following message appears:

IP-address is alive


Note Skip this step if you checked Craft Access Only at Provisioning > Network > General > Gateway Settings.


d. If CTC is not responding, a "Request timed out" message appears. Verify the IP and subnet mask information. Check that the cables connecting the workstation to the ONS 15454 SDH are securely attached. Check the link status by typing:

# ndd -set /dev/device instance 0
# ndd -get /dev/device link_status

For example:

# ndd -set /dev/hme instance 0
# ndd -get /dev/hme link_status

A result of "1" means the link is up. A result of "0" means the link is down.


Note Check the man page for ndd. For example: # man ndd


Step 6 Return to your originating procedure (NTP).


DLP-D55 Set Up a Computer for a Corporate LAN Connection

Purpose

Use this task to set up your computer to access the ONS 15454 SDH through a corporate LAN.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 If your computer is connected to the corporate LAN, go to Step 2. If you changed your computer's network settings for craft access to the ONS 15454 SDH, change the settings back to the corporate LAN access settings. This generally means:

Set the IP Address on the TCP/IP dialog box back to Obtain an IP address automatically (Windows 95 or 98) or Obtain an IP address from a DHCP server (Windows NT, 2000, or XP).

If your LAN requires that DNS or WINS be enabled, change the setting on the DNS Configuration or WINS Configuration tab of the TCP/IP dialog box.

Step 2 If your computer is connected to a proxy server, disable proxy service or add the ONS 15454 SDH nodes as exceptions. To disable proxy service, complete one of the following tasks, depending on the web browser you use:

56 Disable Proxy Service Using Internet Explorer (Windows)

57 Disable Proxy Service Using Netscape (Windows and UNIX)

Step 3 Return to your originating procedure (NTP).


DLP-D56 Disable Proxy Service Using Internet Explorer (Windows)

Purpose

This task disables proxy service for PCs running Internet Explorer.

Tools/Equipment

None

Prerequisite Procedures

None

Required/As Needed

Required if your computer is connected to a network computer proxy server and your browser is Internet Explorer.

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 From the Start menu, select Settings > Control Panel.


Note If you computer is running Windows XP, you can select Control Panel directly from the Start menu. Make sure you are in Classic View before continuing with this procedure.


Step 2 On the Control Panel window, choose Internet Options.

Step 3 From the Internet Properties dialog box, click Connections > LAN Settings.

Step 4 On the LAN Settings dialog box, complete one of the following tasks:

Deselect Use a proxy server to disable the service.

Leave Use a proxy server selected and click Advanced. In the Proxy Setting dialog box under Exceptions, enter the IP addresses of ONS 15454 SDH nodes that you will access. Separate each address with a semicolon. You can insert an asterisk for the host number to include all the ONS 15454 SDHs on your network. Click OK to close each open dialog box.

Step 5 Return to your originating procedure (NTP).


DLP-D57 Disable Proxy Service Using Netscape (Windows and UNIX)

Purpose

This task disables proxy service for PCs and UNIX workstations running Netscape.

Tools/Equipment

None

Prerequisite Procedures

None

Required/As Needed

Required if your computer is connected to a network computer proxy server and your browser is Netscape.

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 Open Netscape.

Step 2 From the Edit menu, choose Preferences.

Step 3 On the Preferences dialog box under Category, choose Advanced > Proxies.

Step 4 On the right side of the Preferences dialog box under Proxies, complete one of the following options:

Choose Direct connection to the Internet to bypass the proxy server.

Choose Manual proxy configuration to add exceptions to the proxy server, then click View. In the Manual Proxy Configuration dialog box under Exceptions, enter the IP addresses of the ONS 15454 SDH nodes that you will access. Separate each address with a comma. Click OK to close each open dialog box.

Step 5 Return to your originating procedure (NTP).


DLP-D58 Provision Remote Access to the ONS 15454 SDH

Purpose

Use this task to connect an ONS 15454 SDH using a LAN modem.

Tools/Equipment

Modem and modem documentation

Prerequisite Procedures

21 Set Up Computer for CTC

Required/As Needed

Required to access the Cisco Transport Controller.

Onsite/Remote

Onsite or remote

Security Level

None


.


Step 1 Connect the modem to the RJ-45 (LAN) port on the TCC2 card or the RJ-45 jack on the MIC-C/T/P FMEC.

Step 2 While referring to the modem documentation, complete the following tasks to provision the modem for the ONS 15454 SDH:

For CTC access, set the modem for Ethernet access.

Assign an IP address to the modem that is on the same subnet as the ONS 15454 SDH.

The IP address the modem assigns to the CTC computer must be on the same subnet as the modem and the ONS 15454 SDH.


Note For assistance on provisioning specific modems, contact the Cisco Technical Assistance Center.


Step 3 Return to your originating procedure (NTP).


NTP-D23 Log into the ONS 15454 SDH GUI

Purpose

This procedure logs into the Cisco Transport Controller, the graphical user interface software used to manage the ONS 15454 SDH. This procedure includes optional node login tasks.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

22 Set Up CTC Computer to Connect to the ONS 15454 SDH

Required/As Needed

Required to access the Cisco Transport Controller.

Onsite/Remote

Onsite or remote

Security Level

Retrieve or higher


.


Step 1 If the computer is not connected to the ONS 15454 SDH, complete the"DLP-D59 Connect Computer to the ONS 15454 SDH" task.

Step 2 Complete the "DLP-D60 Log into CTC" task.


Note For information about navigating in CTC, see Appendix A, "CTC Information and Shortcuts."


Step 3 As needed, complete the "DLP-D61 Create Login Node Groups" task. Login node groups display nodes that are not connected to the login node via DCC.

Step 4 As needed, complete the "DLP-D62 Add a Node to the Current Session or Login Group" task.

Stop. You have completed this procedure.


DLP-D59 Connect Computer to the ONS 15454 SDH

Purpose

This task connects a CTC computer to the ONS 15454 SDH.

Tools/Equipment

Straight-through (Category 5) LAN cable

Prerequisite Procedures

21 Set Up Computer for CTC

22 Set Up CTC Computer to Connect to the ONS 15454 SDH

Required/As Needed

Required to access the Cisco Transport Controller

Onsite/Remote

Onsite or remote

Security Level

Retrieve or higher


.


Step 1 If your computer is set up for a local craft connection, connect a straight-through (Category 5) LAN cable from the PC or Solaris workstation network interface card (NIC) to one of the following:

RJ-45 (LAN) port on the TCC2 card

RJ-45 jack on the MIC-C/T/P FMEC

RJ-45 (LAN) port on a hub or switch to which the ONS 15454 SDH is physically connected


Note For instructions about crimping your own straight-through (Category 5) LAN cables, refer to the Cisco ONS 15454 SDH Troubleshooting Guide.


Step 2 If your computer is set up for a corporate LAN connection, connect a straight-through (Category 5) LAN from the PC or Solaris workstation NIC card to a LAN port.

Step 3 Return to your originating procedure (NTP).


DLP-D60 Log into CTC

Purpose

This task logs into the Cisco Transport Controller, the graphical user interface software used to manage the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

22 Set Up CTC Computer to Connect to the ONS 15454 SDH

Required/As Needed

Required

Onsite/Remote

Onsite or remote

Security Level

Retrieve or higher



Note For information about CTC views and navigation, see Appendix A, "CTC Information and Shortcuts."



Step 1 From the PC connected to the ONS 15454 SDH, start Netscape or Internet Explorer.

Step 2 On the Netscape or Internet Explorer web address (URL) field, enter the ONS 15454 SDH IP address. For initial setup, this is the default address, 192.1.0.2. (This IP address can be displayed on the LCD. Software R4.0 allows suppressing the LCD IP address display.) Press Enter.


Note If you are logging into ONS 15454 SDH nodes running different releases of CTC software, log into the node running the most recent release. If you log into a node with an older release, you receive an INCOMPATIBLE-SW alarm and the IP address of the login node is displayed instead of the node name. To check the software version of a node, select About CTC from the CTC Help menu. To resolve an alarm, refer to the Cisco ONS 15454 SDH Troubleshooting Guide.


A Java Console window displays the CTC file download status. The web browser displays information about your Java and system environments. If this is the first login, CTC caching messages appear while CTC files are downloaded to your computer. The first time you connect to an ONS 15454 SDH, this process can take several minutes. After the download, the CTC Login dialog box appears (Figure 3-2).

Figure 3-2 Logging into CTC

Step 3 On the Login dialog box, type a user name and password (both are case sensitive). For initial setup, type the user name "CISCO15."


Note The CISCO15 user is provided with every ONS 15454 SDH. CISCO15 has superuser privileges, so you can create other users. You must create another Superuser before you can delete the CISCO15 user. CISCO15 is delivered without a password. To create a password for CISCO15, click the Provisioning > Security tabs after you log in and change the password. To set up ONS 15454 SDH users and assign security, go to the "NTP-D30 Create Users and Assign Security" procedure on page 4-3. Additional information is provided in the Cisco ONS 15454 SDH Reference Guide.


Step 4 Each time you log into an ONS 15454 SDH, you can make selections on the following login options:

Node Name—Displays the IP address entered in the web browser and a pull-down menu of previously entered ONS 15454 SDH IP addresses. You can select any ONS 15454 SDH on the list for the login, or you can enter the IP address (or node name) of any new node where you want to log in.

Additional Nodes—Displays a list of login node groups that are created. To create a login node group or add additional groups, see the "DLP-D61 Create Login Node Groups" task.)


Note Topology hosts that were created in previous ONS 15454 SDH releases by modifying the ctc.ini (Windows) or .ctcrc (UNIX) files are displayed as a "Topology Host" group under Additional Nodes.


Disable Network Discovery—Check this box to view only the ONS 15454 SDH (and login node group members, if any) entered in the Node Name field. Nodes linked to the Node Name ONS 15454 SDH through the DCC are not displayed. Using this option can decrease the CTC startup time in networks with many DCC-connected nodes.

Disable Circuit Management—Check this box to disable discovery of existing circuits. Using this option can decrease the CTC initialization time in networks with many existing circuits. This option does not prevent the creation and management of new circuits.

Step 5 Click Login.

If login is successful, the CTC window appears. From here, you can navigate to other CTC views to provision and manage the ONS 15454 SDH. If you need to perform the initial shelf turn up, see Chapter 4, "Turn Up Node." If login problems occur, refer to the Cisco ONS 15454 SDH Troubleshooting Guide.

Step 6 Return to your originating procedure (NTP).


DLP-D61 Create Login Node Groups

Purpose

This task creates a login node group to display ONS 15454 SDHs that have an IP connection but not a DCC connection to the login node.

Tools/Equipment

None

Prerequisite Procedures

21 Set Up Computer for CTC

22 Set Up CTC Computer to Connect to the ONS 15454 SDH

60 Log into CTC

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 From the Edit menu, choose Preferences.

Step 2 Click Login Node Group and Create Group.

Step 3 Enter a name for the group in the Create Login Group Name dialog box. Click OK.

Step 4 Under Members, type the IP address (or node name) of a node you want to add to the group. Click Add. Repeat this step for each node you want to add to the group.

Step 5 Click OK.

The next time you log into an ONS 15454 SDH, the login node group will be available in the Additional Nodes list of the Login dialog box. For example, in Figure 3-3, a login node group, "Test Group," is created that contains the IP addresses for Nodes 1, 4, and 5. During login, if you select Test Group under Additional Nodes and Disable Network Discovery is not selected, all nodes in the figure are displayed. If Test Group and Disable Network Discovery are both selected, Nodes 1, 4, and 5 are displayed. You can create as many login groups as you need. The groups are stored in the CTC preferences file and are not visible to other users.

Figure 3-3 Login Node Group

Step 6 Return to your originating procedure (NTP).


DLP-D62 Add a Node to the Current Session or Login Group

Purpose

This task adds a node to the current CTC session or login node group.

Tools

None

Prerequisite Procedures

None

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Log into an ONS 15454 SDH on the network. See the "DLP-D60 Log into CTC" task for instructions. If you are already logged in, go to Step 2.

Step 2 From the CTC File menu, click Add Node (or click the Add Node button on the toolbar).

Step 3 On the Add Node dialog box, enter the node name (or IP address).

Step 4 If you want to add the node to the current login group, click Add Node to Current Login Group. Otherwise, leave it unchecked.


Note The Add Node to Current Login Group check box is active only if you selected a login group when you logged into CTC.


Step 5 Click OK.

After a few seconds, the new node is displayed on the network view map.

Step 6 Return to your originating procedure (NTP).