Cisco Prime Network Analysis Module 5.1 Command Reference
NAM CLI Commands: show clock details - show monitor urlfilter request
Downloads: This chapterpdf (PDF - 210.0KB) The complete bookPDF (PDF - 2.31MB) | Feedback

NAM CLI Commands: show clock details - show monitor urlfilter

Table Of Contents

NAM CLI Commands:
show clock details - show monitor urlfilter

show clock details

show configuration

show counters

show cpu

show data-source

show date

show debug log-levels

show debug messages

show debug metric-engine

show device

show email

show entity

show hosts

show inventory

show ip

show license

show log config

show log patch

show log report

show log upgrade

show managed- device

show memory

show metric export

show monitor protocol encapsulation

show monitor protocol all

show monitor rtp-stream

show monitor rtp-stream filter

show monitor urlcollection

show monitor urlfilter


NAM CLI Commands:
show clock details - show monitor urlfilter


This chapter describes the following NAM CLI commands:

show clock details

show configuration

show counters

show cpu

show data-source

show date

show debug log-levels

show debug messages

show debug metric-engine

show device

show email

show entity

show hosts

show inventory

show ip

show license

show log config

show log patch

show log report

show log upgrade

show managed- device

show memory

show metric export

show monitor protocol encapsulation

show monitor protocol all

show monitor rtp-stream

show monitor rtp-stream filter

show monitor urlcollection

show monitor urlfilter

show clock details

To show clock details on the NAM, use the show clock details command.

show clock details


Note This command is only valid for Cisco NAM 2200 series appliances.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on Cisco NAM 2200 series appliances.

Examples

The following example shows how to display clock settings.

root@nam.cisco.com# show clock details
System Time:    Thu Nov  4 18:25:41 PDT 2010

show configuration

To display the NAM running configuration, use the show configuration command.

show configuration

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

The following configurations are not included in the generated configuration file:

Reports

CLI users

Supervisor engine community strings

Examples

This example shows how to display the NAM running configuration:

Root@localhost# show configuration

***** NAM configuration *****
Time: Thu Nov  4 18:12:24 2010

preferences
  entries-per-screen 15
  refresh-interval 300
  graph-bars 135586104
  resolve-hostname disable
  data-displayed bytes
  format-large-number disable
  number-notation commas-dot
  exit
!
monitor art response-times
  report-interval 1800
  rsp-time1 1
  rsp-time2 5
  rsp-time3 10
  rsp-time4 50
  rsp-time5 100
  rsp-time6 500
  rsp-timeout 1000
  exit
!

Examples

config clear

show counters

To display the counters for data aggregation table, use the show counters command.

show counters

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the counters for data aggregation table:

root@nam235Cat6k.cisco.com# show counters ?
long-term                 - show long-term collection counters
nde-export                - show collection counters for NDE export
short-term                - show short-term collection counters

show cpu

To display the Central Processing Unit (CPU) utilization, use the show cpu command.

show cpu

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the CPU utilization:

root@nam235Cat6k.cisco.com# show cpu

NOTE: For more details on system resources including CPU
utilization, visit the Administration -> System -> Resources
page in the NAM Traffic Analyzer web application.
root@nam235Cat6k.cisco.com#

show data-source

To display the data-sources, use the show data-source command.

show data-source

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the data-sources:

root@nam235Cat6k.cisco.com# show data-source

DATA SOURCE ID   : 1
DATA SOURCE NAME : DATA PORT 1
TYPE             : Data Port
PORT NUMBER      : 1
-----------

DATA SOURCE ID   : 2
DATA SOURCE NAME : DATA PORT 2
TYPE             : Data Port
PORT NUMBER      : 2
-----------

show date

To display the current date and time, use the show date command.

show date

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the current date and time:

Root@localhost# show date
Thu Jan 09 09:38:01 2003

Related Commands

show time
time

show debug log-levels

To display log level settings, use the show debug log-levels command.

show debug log-levels

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default behavior or settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example shows log level settings:

root@nam.cisco.com# show debug log-levels
Debug Logging: enabled
Feature OTHER (1): error (1)
Feature CDP (2): error (1)
Feature POLLD (3): error (1)
Feature SWPOLLD (4): error (1)
Feature TREND_DAEMON (5): error (1)
Feature TREND_RPC (6): error (1)
Feature TREND_SNMP (7): error (1)
Feature MAIN (8): error (1)
Feature MISC (9): error (1)
Feature SNMP (10): error (1)
Feature SRSNMP (11): error (1)
Feature ENTITY (12): error (1)
Feature RMON (13): error (1)
Feature RPC (14): error (1)
Feature DSRC (15): error (1)
Feature WAAS (16): error (1)
Feature PARSER (17): error (1)
Feature PPROC (18): error (1)
Feature FM (19): error (1)
Feature FR (20): error (1)
Feature COLL_SHARED (21): error (1)
Feature RTP (22): error (1)
Feature METRIC_ENGINE (23): error (1)
Feature ART (24): error (1)
Feature URL_COLLECTION (25): error (1)
Feature PORT_TABLE (26): error (1)
Feature MPLS_STATS (27): error (1)
Feature ETHERSTATS (28): error (1)
Feature CAPTURE (29): error (1)
Feature RMON1_HOST (30): error (1)
Feature RMON1_MATRIX (31): error (1)
Feature RMON2_ADDRMAP (32): error (1)
Feature RMON2_PDIST (33): error (1)
Feature RMON2_HOST (34): error (1)
Feature RMON2_MATRIX (35): error (1)
Feature DSMON_STATS (36): error (1)
Feature DSMON_PDIST (37): error (1)
Feature DSMON_HOST (38): error (1)
Feature DSMON_MATRIX (39): error (1)
Feature SMON_PRIO (40): error (1)
Feature SMON_VLAN (41): error (1)
 

show debug messages

To display NAM log file contents, use the show debug messages command.

show debug messages

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default behavior or settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example shows the log file contents:

root@nam.cisco.com# show debug messages
2008-10-14 00:07:11 *** FM Metric Engine 1 created (iThread 3)
2008-10-14 00:07:11 MAIN: Flow reaper starting, LWP = 1381
2008-10-14 00:07:11 Packet data and flow processing layers started successfully.
2008-10-14 00:07:11 WAAS: Load autoconfig: enables:1 client:1 cltwan:0 svrwan:0                                                                                             
server:0 passthru:0
2008-10-14 00:07:11 *** WAAS Flow Agent (FA) manager module initialized ***
2008-10-14 00:07:11 Load SA Export config SA_EXPORT_ENABLED = 0
2008-10-14 00:07:11 *** Configure SuperAgent export: export disabled
2008-10-14 00:07:11 *** ART Metric Engine post initialization done. ***
2008-10-14 00:07:11 MAIN: dbgport_init: No cfg file!
2008-10-14 00:07:11 MAIN: Offtime LWP = 1382
2008-10-14 00:07:11 RPC: RPC LWP = 1383
2008-10-14 00:16:19 mond: exiting on signal 15.
2008-10-14 00:19:21 mond starting.
2008-10-14 00:19:21 MAIN: Timer LWP = 1570
2008-10-14 00:19:21 MAIN: Timekeeping LWP = 1571

show debug metric-engine

To display metric-engine log file, use the show debug metric-engine command.

show debug metric-engine

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display metric-engine log file:

root@nam235Cat6k.cisco.com# show debug metric-engine

show device

To display the remote devices like ERSPAN, NetFlow, and WAAS, use the show device command.

show device

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the remote devices:

root@localhost# show device

show email

To display email settings that are used for e-mailing alarm messages or scheduled reports, use the email command.

show email

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display email values:

root@localhost# show email
Email
  Server: example-email.domain.com
  Mail Alarm: enabled
  Alarm Recipients: admin@domain.com another_admin@domain.com
root@localhost# 

Related Commands

device erspan
email

show entity

To display the serial number and the values of the entity MIB entPhysicalAlias and entPhysicalAssetID, use the show entity command.

show entity

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display entity values:

root@localhost# show entity
Serial Number : SAD061506JU
Alias         :
Asset ID      :

Related Commands

entity alias
entity assetid

show hosts

To display the hosts entries, use the show hosts command.

show hosts

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the hosts entries:

Root@localhost# show hosts
# $Id: hosts,v 1.4 2002/04/04 01:47:51 pwildi Exp $
#
127.0.0.1               localhost localhost.localdomain

127.0.0.11              slot1
127.0.0.21              slot2
127.0.0.31              slot3
127.0.0.41              slot4
127.0.0.51              slot5
127.0.0.61              slot6
127.0.0.71              slot7
127.0.0.81              slot8

111.10.9.18 switch1 lab

show inventory

To display the system inventory information for a NAM device, use the show inventory command.

show inventory

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

The show inventory command allows you to view the UDI for a NAM device. This identity information is stored in the NAM device's non-volatile memory.

PID—Product identification (ID) number of the device

VID—Version ID of the device. Displays as 0 if the version number is not available.

SN—Serial number of the device

Examples

The following example shows the system inventory information:

root@nam.cisco.com# show inventory
PID:WS-SVC-NAM-2  VID:V05  SN:SAD1151075B

show ip

To display the NAM IP parameters, use the show ip command.

show ip

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the NAM IP parameters:

Root@localhost# show ip
IP address:             101.10.11.189
Subnet mask:            255.255.255.255
IP Broadcast:           111.20.255.255
DNS Name:               namlab-kom9.cisco.com
Default Gateway:        111.20.98.125
Nameserver(s):          111.69.2.135
HTTP server:            Enabled
HTTP secure server:     Disabled
HTTP port:              80
HTTP secure port:       443
TACACS+ configured:     No
Telnet:                 Enabled
SSH:                    Disabled

Related Commands

ip address
ip broadcast
ip gateway
ip host
ip hosts add
ip hosts delete
ip http secure port
ip http secure generate
ip http secure server
ip http tacacs+
ip interface

show license

To display the information about the license installed on the WAE device.

show license


Note This command is not valid for NAM-1, NAM-2, NME-NAM-80S, NME-NAM-120S, or the Cisco NAM 2200 Series appliances.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is valid only on the NAM Virtual Blade.

Examples

This example shows how to display the NAM Virtual Blade license information for the WAE device.

Root@localhost# show license


Related Commands

license install
config upload

show log config

To display the maintenance image configuration import log entries, use the show log config command.

show log config

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the maintenance image import log entries:

Root@localhost# show log config

Related Commands

config clear
show log report
upgrade

show log patch

To display the patch log entries, use the show log patch command.

show log patch

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the maintenance image import log entries:

Root@localhost# show log patch
2005/01/17 21:11 Sucessfully downloaded ftp://guest@namlab-pc1//home/guest/patch
_rpms/nam-app.3-4.cryptoK9.patch.1-0.bin.
2005/01/17 21:11 Patch nam-app.3-4.cryptoK9.patch.1-0.bin signature verified.
2005/01/17 21:11 Successfully applied patch /usr/local/nam/patch/workdir/nam-app
.3-4.cryptoK9.patch.1-0.bin.

Related Commands

config clear
show log report
upgrade

show log report

To display the import log entries, use the show log report command.

show log report

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the import log entries:

Root@localhost# show log report

Related Commands

show log config

show log upgrade

To display the maintenance image upgrade log entries, use the show log upgrade command.

show log upgrade

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the maintenance image upgrade entries:

Root@localhost# show log upgrade
Fri Aug 23 10:32:27 2002 : path: ftp://namlab-pc1/pub/rmon/MP-KPLUS
 Fri Aug 23 10:32:27 2002 : file: mp-dev.1-2-0-5.bin
 Fri Aug 23 10:32:27 2002 : extn: .gz
 Fri Aug 23 10:32:27 2002 : Downloading the image...
 Fri Aug 23 10:32:28 2002 : Successfully downloaded the image...
 Fri Aug 23 10:32:28 2002 : Uncompressing the image...
 Fri Aug 23 10:32:29 2002 : Finished uncompressing the file /tmp/mp-dev.1-2-0-5. bin.gz.
 Fri Aug 23 10:32:29 2002 : Successfully uncompressed the image.
 Fri Aug 23 10:32:29 2002 : Verifying the image...
 Fri Aug 23 10:32:29 2002 : opening file /tmp/mp-dev.1-2-0-5.bin.ver
 Fri Aug 23 10:32:30 2002 : Successfully verified the image.
 Fri Aug 23 10:32:30 2002 : Partition '/dev/hda1' unmounted.
 Fri Aug 23 10:32:30 2002 : Applying the Maintenance image.
 Fri Aug 23 10:32:30 2002 : This process may take several minutes...
 Fri Aug 23 10:32:30 2002 : Writing mbr...
 Fri Aug 23 10:32:30 2002 : Successfully wrote mbr.
 Fri Aug 23 10:32:30 2002 : Number of Sectors: 31
 Fri Aug 23 10:32:30 2002 : Writing grub and maint image.
 Fri Aug 23 10:33:18 2002 : Successfully wrote the maint image.
 Fri Aug 23 10:33:18 2002 : Partition '/dev/hda1' mounted.
 Fri Aug 23 10:33:18 2002 : Performing post install...
 Fri Aug 23 10:33:18 2002 : File /usr/local/nam/falcon_version copied to /mnt/mp 
/boot/appl/daughter_card.info.
 Fri Aug 23 10:33:18 2002 : Maintenance image upgrade completed successfully.

Related Commands

show managed- device

To display the managed-device address, use the show managed-device command.

show managed-device


Note This command is not valid for NAM-1, NAM-2, NME-NAM-80S, NME-NAM-120S, or the Cisco Virtual Blade device.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on Cisco NAM 2200 Series appliances.

Examples

This example shows how to display the managed-device address:

root@localhost# show managed-device

show memory

To display the installed memory, available memory, and the memory being used by the system, use the show memory command.

show memory

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the NAM memory:

Root@localhost# show memory
Installed:      858 MB
Available:      240 MB
System Usage:   617 MB

Related Commands

show cdb

show metric export

To show metric export configuration, use the show metric export command.

show metric export

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example shows the metric export configuration:

root@nam.cisco.com# show metric export
Metric export: enabled
Host: 10.0.0.1
Port: 9995
Export non-WAAS traffic: enabled

show monitor protocol encapsulation

To display the encapsulation configurations, use the show monitor protocol encapsulation command.

show monitor protocol encapsulation

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the encapsulation configurations:

root@nam.cisco.com# show monitor protocol encapsulation

Related Commands

monitor protocol encapsulation

show monitor protocol all

To display all of the protocols in the protocol directory, use the show monitor protocol all command.

show monitor protocol all

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display all of the protocol configurations:

Root@localhost#  show monitor protocol all
Control Index:                 46232
Data Source:                   dataport1
Owner:                         LocalMgr
Status:                        1
Root@localhost#

show monitor rtp-stream

To display the RTP monitoring and alarm threshold settings, use the show monitor rtp-stream command.

show monitor rtp-stream


Note This command is not supported on the NAM Virtual Blade.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

This example shows how to display the RTP-stream monitoring settings and alarm thresholds.

root@localhost# show monitor rtp-stream
root@localhost# 

Related Commands

monitor rtp-stream enable
monitor urlcollection

show monitor rtp-stream filter

To display the URL collection configuration, use the show monitor rtp-stream filter command.

show monitor rtp-stream filter


Note This command is not supported on the NAM Virtual Blade.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

This example shows how to display the URL collection statistics:

root@localhost# show monitor rtp-stream filter
root@localhost# 

Related Commands

monitor rtp-stream filter

show monitor urlcollection

To display the URL collection configuration, use the show monitor urlcollection command.

show monitor urlcollection


Note This command is not supported on the NAM Virtual Blade.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

This example shows how to display the URL collection statistics:

root@localhost# show monitor urlcollection
root@localhost# 

Related Commands

monitor urlcollection

show monitor urlfilter

To display the URL filter configuration, use the show monitor urlfilter command.

show monitor urlfilter [control-index]


Note This command is not supported on the NAM Virtual Blade.


Syntax Description

control-index

(Optional) Specifies the URL filter control index.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

This example shows how to display the URL filter configuration:

root@localhost# show monitor urlfilter
root@localhost# 

Related Commands

monitor urlfilter