Cisco Prime Network Analysis Module 5.1 Command Reference
NAM CLI Commands: metric export host - show certificate request
Downloads: This chapterpdf (PDF - 261.0KB) The complete bookPDF (PDF - 2.31MB) | Feedback

NAM CLI Commands: metric export host - show certificate request

Table Of Contents

NAM CLI Commands:
metric export host - show certificate request

metric export host

metric export non-waas traffic

monitor protocol encapsulation

monitor rtp-stream enable

monitor rtp-stream filter

monitor rtp-stream threshold

monitor urlcollection

monitor urlfilter

netflow input port

nslookup

password

patch

pid-sn

ping

preferences

reboot

remote-storage nfs

remote-storage iscsi

rmwebusers

show access-log

show application app-id

show application eng-id

show application group

show audit-trail

show autocreate-data-source

show cdb

show cdp settings

show certificate

show certificate-request


NAM CLI Commands:
metric export host - show certificate request


This chapter describes the following NAM CLI commands:

metric export host

metric export non-waas traffic

monitor protocol encapsulation

monitor rtp-stream enable

monitor rtp-stream filter

monitor rtp-stream threshold

monitor urlcollection

monitor urlfilter

netflow input port

nslookup

password

patch

pid-sn

ping

preferences

reboot

remote-storage nfs

remote-storage iscsi

rmwebusers

show access-log

show application app-id

show application eng-id

show application group

show audit-trail

show autocreate-data-source

show cdb

show cdp settings

show certificate

show certificate-request

metric export host

To configure the metric export host, use the metric export host command. To disable metric export, use the no form of this command.

metric export host ip-address [port]

no metric export

Syntax Description

ip-address

Specifies the IPv4 address of the external reporting console.

port

Port the external reporting console is listening on for incoming packets (optional).


Defaults

The default port is 9995.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Use this command to export ART metrics to an external reporting console.

Examples

The following example specifies the reporting console's IP address as the source to collect ART metrics, then removes this configuration.

root@nam.cisco.com# metric export 10.0.0.1 9995
root@nam.cisco.com# no metric export

metric export non-waas traffic

To send SPAN traffic (non-WAAS traffic) to an external reporting console, use the metric export non-waas traffic command. To disable metric export, use the no form of this command.

metric export non-waas traffic

no metric export non-waas traffic

Syntax Description

This command has no arguments or keywords.

Defaults

Export is disabled.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Use this command to export non-waas (SPAN traffic) metrics to an external reporting console.

Examples

The following example shows how to send non-WAAS traffic to an external reporting console, then removes this configuration:

root@nam.cisco.com# metric export non-waas traffic
root@nam.cisco.com# no metric export non-waas traffic
 

monitor protocol encapsulation

To set the protocol encapsulation, use the monitor protocol encapsulation command. To disable the protocol encapsulation, use the no form of this command.

monitor protocol encapsulation

no monitor protocol encapsulation

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to set the monitor protocol encapsulation.

root@nam.cisco.com# monitor protocol encapsulation
gre-ip                    - encapsulation type
gtp                       - encapsulation type
ip-esp                    - encapsulation type
ip-ipv4                   - encapsulation type
ip-ipv6                   - encapsulation type
root@nam.cisco.com# monitor protocol encapsulation

Related Commands


show monitor protocol encapsulation

monitor rtp-stream enable

To enable RTP stream monitoring, use the monitor rtp-stream enable command. To disable RTP stream monitoring, use the no form of this command.

monitor rtp-stream enable

no monitor rtp-stream enable


Note This command is not supported on the NAM Virtual Blade.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

This example shows how to enable RTP stream monitoring.

root@localhost# monitor rtp-stream enable

This example shows how to disable RTP stream monitoring.

root@localhost# no monitor rtp-stream enable

Related Commands


monitor rtp-stream filter

monitor rtp-stream filter

To set a RTP stream filtering entry, use the monitor rtp-stream filter command. To remove a RTP stream filtering entry, use the no form of this command.

monitor rtp-stream filter source-address source-mask dest-address dest-mask

Syntax Description

source-address

Specifies the source address of the RTP stream being filtered.

source-mask

Specifies the subnet mask of the source address of the RTP stream being filtered.

dest-address

Specifies the destination address of the RTP stream being filtered.

dest-mask

Specifies the subnet mask of the RTP stream being filtered.



Note This command is not supported on the NAM Virtual Blade.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

This example shows how to enable RTP stream filtering:

root@localhost# monitor rtp-stream filter 1.2.3.0 255.255.255.0 4.5.0.0 255.255.0.0

Related Commands

metric export host

monitor rtp-stream threshold

To set the alarm threshold for the different RTP stream monitoring types, use the monitor rtp-stream threshold command. To disable the alarm threshold RTP stream monitoring, use the no form of this command.

monitor rtp-stream threshold <key_word>

no monitor rtp-stream threshold <key_word>

Syntax Description

Key Word

Action

actual-pkt-loss

Specifies the actual packet loss percentile threshold and enables the actual packet loss threshold alarm.

adjusted-pkt-loss

Specifies the adjusted packet loss percentile threshold and enables the adjusted packet loss threshold alarm.

jitter

Specifies the jitter alarm threshold and enables the jitter threshold alarm in milliseconds.

mos

Specifies the MOS score threshold and enables the MOS score alarm.

soc

Specifies the seconds of concealment threshold and enables the soc alarm.

ssc

Specifies the severe seconds of concealment threshold and enables the ssc alarm.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to set an alarm threshold of 6% for RTP stream monitoring of lost packets.

root@NAM.cisco.com# monitor rtp-stream threshold adjusted-pkt-loss 6
Successfully set adjusted-pkt-loss alarm.
root@NAM.cisco.com#

monitor urlcollection

To enter the URL collection submode and configure URL collections, use the monitor urlcollection command. To disable the URL collection, use the no form of this command.

monitor urlcollection

no monitor urlcollection


Note This command is not supported on the NAM Virtual Blade.


Syntax Description

This command has no keywords or arguments.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

When you enter the URL collections submode, the following commands are available:

? or help—Displays help; see the help command.

cancel—Discards changes and exits from the subcommand mode; see the autocreate-data-source command section.

data-source nam-data-source-nameSpecifies the NAM data source name.

exit—Saves changes and exits from the subcommand mode; see the exit command.

ignore(Optional) Sets the host, path, and the URL matching argument.

ignore host—Specifies that you ignore or do not ignore the URL's host part when collecting URL collection data.

ignore path—Specifies that you ignore or do not ignore the URL's parth part when collecting URL collection data.

ignore url-arg—Specifies that you ignore or do not ignore the URL's arguments when collecting URL collection data.

ignore enable | disableEnables or disables this command.

match-only string(Optional) Specifies collecting only the URL data that matches the string in the URL.

max-entry 100 | 50 | 1000(Optional) Specifies the maximum of URL collection entries.

recycle enable | disableEnables or disables aging of the URL collection data entries.

There is only one URL collection in NAM. The collection owner is always LocalMgr. The index is always one.

Examples

This example shows how to configure URL collection:

root@localhost# monitor urlcollection

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@localhost(sub-monitor-url-collection)# ?
?                         - display help
cancel                    - discard changes and exit from subcommand mode
data-source               - specify the collection data source (*)
exit                      - exit from the subcommand mode
help                      - display help
ignore                    - set url collection data matching schemes
match-only                - match string for url collection data
max-entry                 - set max number data entries of url collection
recycle                   - enable or disable aging of url collection data entries

(*) - denotes a mandatory field for this configuration.

root@localhost(sub-monitor-url-collection)#

Related Commands

cdp interval
show monitor urlcollection

monitor urlfilter

To enter the URL filter collection configuration subcommand mode, and then configure URL filters, use the monitor urlfilter command. To remove the URL filters from the configuration, use the no form of this command.

monitor urlfilter

no monitor urlfilter control-index


Note This command is not supported on the NAM Virtual Blade.


Syntax Description

control-index

Specifies the collection control index. Range is from 1 to 65535.


Defaults

The control index is random.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

When you enter the monitor URL filter subcommand mode, the following commands are available:

?—Displays help.

cancel—Discards changes and exits from the subcommand mode.

control-index control-indexSpecifies the URL entry's control index. Range is from 1 to 65535. Default is random.

description string(Optional) Specifies the URL filter's description string.

exit—Saves changes and exits from the subcommand mode; see the exit command.

help—Displays help.

host-regexp—Specifies the regular expression for the URL's host.

path-regexpSpecifies the regular expression of the URL's path.

protocol-encap—(Optional) Specifies the protocol encapsulation of the HTTP packet.

The clear configuration command removes the URL filters from the configuration. There is no SNMP support for configuring the URL filters.

Examples

This example shows how to configure URL filters:

root@nam# monitor urlfilter
Entering into subcommand mode for this command.
Type 'exit' to come out of this mode.
Type 'cancel' to discard changes and to come out of this mode.
root@nam(sub-monitor-url-filter)# control-index 2
root@nam(sub-monitor-url-filter)# description urlfilter example
root@nam(sub-monitor-url-filter)# host-regexp www.example.com
root@nam(sub-monitor-url-filter)# protocol-encap ipv4
root@nam(sub-monitor-url-filter)# exit
Sucessfully created urlfilter entry.
root@nam# show monitor urlfilter
Description: urlfilter example
    Control index:             2
    Protocol encapsulation:    IPv4
    URL's host string:         www.example.com
    URL's path string:         (not-set)

To remove this URL filter entry, use the no form of the command:

root@nam# no monitor urlfilter 2
Successfully delete urlfilter entry.

Related Commands

cdp interval
show monitor urlfilter

netflow input port

To set a specified value of the input NetFlow UDP port on NAM, use the netflow input port [port] command.

netflow input port [port]


Note In case this CLI is not used, NAM retains the default port 3000 to listen to incoming NDEs. When invoked, the CLI prints both old and new UDP port numbers, if successfully completed.


Syntax Description

port

Specifies the input UDP port number, valid values 1 - 65535.


Defaults

The default port is 3000.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to use the netflow input port command.

root@localhost# netflow input port 9101
NetFlow input port 3000 changed to 9101

nslookup

To configure name server queries, use the nslookup command.

nslookup hostname [server]

Syntax Description

hostname

Specifies the name server query host.

server

(Optional) Specifies the name server to query.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to configure name server queries:

root@localhost.cisco.com# nslookup www.yahoo.com
Server:        127.0.0.1
Address:       127.0.0.1#53

Non-authoritative answer:
www.yahoo.com   canonical name = www.yahoo.akadns.net.
Name:  www.yahoo.akadns.net
Address:66.218.71.80
root@localhost.cisco.com#

password

To set a new password, use the password command.

password username

Syntax Description

username

Sets the user login name whose password will be changed.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

There are only two valid users, root and guest.

Examples

This example shows how to set a password:

root@localhost.cisco.com# password root
Changing password for user root
New UNIX password:
Retype new UNIX password:
passwd:all authentication tokens updated successfully
root@localhost.cisco.com# 

patch

To download and install a software patch, use the patch command.

patch ftp://user:passwd@host/full-path/filename

Syntax Description

ftp://user:passwd@host/full-path/filename

Sets the path to download the patch.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to download and install a patch:

root@localhost.cisco.com# patch 
ftp://hostname/fullpath/c6nam-3.6-strong-cryptoK9-patch-1-0.bin
 
Proceeding with installation. Please do not interrupt.
If installation is interrupted, please try again.
 
Downloading c6nam-3.6-strong-cryptoK9-patch-1-0.bin. Please wait...
ftp://hostname/fullpath/c6nam-3.6-strong-cryptoK9-patch-1-0.bin (1K)
-                         [########################]       1K | 1886.33K/s
1891 bytes transferred in 0.00 sec (1569.00k/sec)
 
Verifying c6nam-3.6-strong-cryptoK9-patch-1-0.bin. Please wait...
Patch c6nam-3.6-strong-cryptoK9-patch-1-0.bin verified.
 
Applying /usr/local/nam/patch/workdir/c6nam-3.6-strong-cryptoK9-patch-1-0.bin. Please 
wait...
########################################### [100%]
########################################### [100%]
 
Patch applied successfully.
root@localhost.cisco.com#

Related Commands

show patches
show version

pid-sn

To enter the Product ID and Serial number of a WAE device for node locking with a NAM Virtual Blade product license, use the pid-sn command.

pid-sn PIDnnnn SNnnnn

Syntax Description

PIDnnnn

Specifies the Product ID of the WAE device.

SNnnnn

Specifies the serial number of the WAE device.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is valid only on NAM Virtual Blade platforms.

Examples

This example shows how to ener the Product ID and serial number of a WAE device:

root@localhost# pid-sn WAE-674-K9 KXQCDHDR
root@localhost# 

ping

To check connectivity to a network device, use the ping command.

ping [-n | -v] [-c count] [-i wait] [-p pattern] [-s packetsize] hostname | IP address

Syntax Description

-n

(Optional) Displays the network addresses as numbers.

-v

(Optional) Specifies verbose output.

-c count

(Optional) Stops the ping after sending the count of ECHO_REQUEST packets.

-i wait

(Optional) Specifies the time interval in seconds between sending each packet.

-p pattern

(Optional) Specifies the pad bytes to fill out packets sent in the ping. You may specify up to 16 pad bytes to fill out packets being sent.

-s packetsize

(Optional) Sets the 8 bytes of ICMP header data.

hostname

Sets the hostname of the network device to ping.

IP address

Specifies the IP address of the network device to ping.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to check the connectivity of a network device with ping:

root@localhost# ping -n -v ralph 100.20.19.23
root@localhost# 

preferences

To enter the preferences subcommand mode, and then configure how your screen displays information, use the preferences command.

preferences

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the preferences subcommand mode, the following commands are available:

cancel—Discards changes and exits from the subcommand mode.

csv-export all | current-screen Sets the comma-separated values export monitor data options.

data-displayed bits | bytesSpecifies how the data is displayed in bits or bytes.

entries-per-screen 1-100—(Optional) Sets the number of rows to display in tabular screens. Default is 15.

exit—Saves changes and exits from the subcommand mode; see the exit command.

format-large-number enable | disableDisplays the GUI counters in large numbers: K(kilo), M(mega), or G(giga).

graph-bars 1-15— (Optional) Sets the number of bars on a displayed graph. Default is 10.

help—Displays help; see the help command.

number-notation commas-dot | dots-comma | spaces-commaSets the number notation to commas or dot and so forth. For example: 1,000 or 1.000 or 300, 10.

refresh-interval 15-3600(Optional) Sets the screen refresh interval in seconds. Default is 60.

resolve-hostname enable | disable(Optional) Enables or disables hostname resolution. Default is enable.

Examples

This example shows how to configure preferences for your screen display:

root@localhost.cisco.com# preferences
Entering into subcommand mode for this command.
Type 'exit' to come out of this mode.
Type 'cancel' to discard changes and to come out of this mode.
root@localhost.cisco.com(sub-preferences)# entries-per-screen 15
root@localhost.cisco.com(sub-preferences)# refresh-interval 60
root@localhost.cisco.com(sub-preferences)# graph-bars 10
root@localhost.cisco.com(sub-preferences)# hostname-resolution disable
root@localhost.cisco.com(sub-preferences)# data-displayed bytes
root@localhost.cisco.com(sub-preferences)# format-large-number enable
root@localhost.cisco.com(sub-preferences)# number-notation comma-dot
root@localhost.cisco.com(sub-preferences)# exit
NAM web interface preferences updated successfully.data

This example shows how to display the configured preferences:

root@localhost.cisco.com# show preferences
Entries per screen:   15
Refresh interval:     60 secs
Number of graph bars: 10
Hostname resolution:  Disabled
Data displayed in:    Bytes
Format large number:  No
Number notation:      Commas-dot
root@localhost.cisco.com# 

Related Commands

show preferences

reboot

To shut down and then restart NAM, use the reboot command.

reboot

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to reboot the NAM:

root@localhost# reboot
Reboot the NAM? (Y/N) [N]:
root@localhost# 

remote-storage nfs

To set a NFS remote storage for capturing data and enter the configuration command mode, use the remote-storage nfs command. To remove a NFS remote storage for captured data, use the no remote-storage name command.

remote-storage nfs

no remote-storage name

Syntax Description

name

Specifies the name for the NFS remote storage being removed.



Note This command is not supported on the NAM Virtual Blade.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Usage Guidelines

When you enter the web user subcommand mode, the following commands are available:

? or help—Displays help; see the help command.

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command.

server WORDNFS server dns hostname or ip address.

dir WORDAn absolute directory with read write permission at the nfs server.

name WORDName of the nfs remote storage entry.

Examples

This example shows how to configure NFS remote storage for capturing data:

root@hostname.cisco.com# remote-storage nfs
Entering into subcommand mode for this command.
Type 'exit' to come out of this mode.
Type 'cancel' to discard changes and to come out of this mode.
root@hostname.cisco.com(sub-remote-storage_nfs)# ?

root@hostname.cisco.com#

Related Commands

remote-storage iscsi
show remote-storage

remote-storage iscsi

To set an iSCSI remote storage for capture data and enter the configuration command mode, use the remote-storage iscsi command. To remove an iSCSI remote storage entry for capture data, use the no remote-storage name command.

remote-storage iscsi

no remote-storage name

Syntax Description

name

Specifies the name for the NFS remote storage being removed.



Note This command is not supported on the NAM Virtual Blade.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

When you enter the web user subcommand mode, the following commands are available:

? or help—Displays help; see the help command.

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command.

name WORDName of the iSCSI remote storage entry.

server WORDSCSI server dns hostname or ip address.

target WORDiSCSI target name provided by the iSCSI server admin.

format none partition-numberUntouch the remote iSCSI target partition table and make the NAM use "partition-number" for storing its capture data.

format one-linuxFormat the remote iSCSI target with one linux ext2 partition before using it to store NAM capture data.

Examples

This example shows how to configure a remote storage for caputuring iSCSI data:

root@hostname.cisco.com# remote-storage iscsi
Entering into subcommand mode for this command.
Type 'exit' to come out of this mode.
Type 'cancel' to discard changes and to come out of this mode.
root@hostname.cisco.com(sub-remote-storage_iscsi)# ?

root@hostname.cisco.com#

Related Commands

remote-storage nfs
show remote-storage

rmwebusers

To remove all web users from the local web user database, use the rmwebusers command.

rmwebusers

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to remove web users from the local web user database:

root@localhost.cisco.com# rmwebusers
 
WARNING:Doing this will stop the web server and remove
all locally defined web users from web user database.
 
Are you sure you want to continue (y/n) [n]? y
 
Disabling HTTP server...
Successfully disabled HTTP server.
 
All locally defined web users have been
removed from web user database.
root@localhost.cisco.com#

Related Commands

show web-user

show access-log

To display the web access log, use the show access-log command.

show access-log

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the web access log:

Root@localhost# show access-log
11 Mar 2003, 12:23:38   152.20.27.182   -       Access denied (no login session)
 /error.php
11 Mar 2003, 12:23:39   152.20.27.182   -       Access denied (no login session)
 /error.php
11 Mar 2003, 12:23:39   152.20.27.182   -       Access denied (no login session)
 /error.php
11 Mar 2003, 12:23:39   152.20.27.182   -       Access denied (no login session)
 /error.php

show application app-id

To display all applications, use the show application app-id command.

show application app-id

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display all applications:

root@NAM.cisco.com# show application app-id
sample-l3:1 (16777217) icmp
sample-l3:2 (16777218) igmp
sample-l3:4 (16777220) ip
sample-l3:6 (16777222) tcp
sample-l3:8 (16777224) egp

Related Commands

show application eng-id

To display application information per engine ID, use the show application eng-id command.

show application eng-id

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display application information per engine ID:

root@NAM.cisco.com# show application eng-id 1
sample-l3:1 (16777217) icmp
sample-l3:2 (16777218) igmp
sample-l3:4 (16777220) ip
sample-l3:6 (16777222) tcp
sample-l3:8 (16777224) egp

Related Commands

application

show application group

To display application groups, use the show application group command.

show application group [group-name]

Syntax Description

group-name

(Optional) Specifies the application group name.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display application groups:

root@namlab-kom10.cisco.com# show application group
Application Group: File-Transfer
    Number of Protocols: 5
      - ftp
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.21.4.0.1.0.0
      - ftp-data
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.20.4.0.1.0.0
      - ftps
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.3.222.4.0.1.0.0
      - ftps-data
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.3.221.4.0.1.0.0
      - tftp
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.0.69.4.0.1.0.2

Application Group: Peer-to-Peer
    Number of Protocols: 12
      - gnutella(6346)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.24.202.4.0.1.0.0
      - gnutella(6347)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.24.203.4.0.1.0.0
      - fasttrack(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.4.190.4.0.1.0.0
      - fasttrack(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.4.190.4.0.1.0.0
      - winmx(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.24.113.4.0.1.0.
      - winmx(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.26.43.4.0.1.0.0
      - edonkey(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.18.57.4.0.1.0.0
      - edonkey(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.18.53.4.0.1.0.0
      - hotline
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.21.124.4.0.1.0.0
      - soulseek
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.8.186.4.0.1.0.0
      - directconnect
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.1.155.4.0.1.0.0
      - bittorrent
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.26.225.4.0.1.0.0

Application Group: Web
    Number of Protocols: 2
      - http
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.80.4.0.1.0.0
      - https
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.1.187.4.0.1.0.0

Application Group: Database
    Number of Protocols: 9
      - sql*net
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.66.4.0.1.0.0
      - sqlserv(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.0.118.4.0.1.0.0
      - sqlserv(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.118.4.0.1.0.0
      - ms-sql-mon(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.5.154.4.0.1.0.0
      - ms-sql-mon(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.5.154.4.0.1.0.0
      - ms-sql-ser(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.5.153.4.0.1.0.0
      - ms-sql-ser(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.5.153.4.0.1.0.0
      - oracle-server(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.5.245.4.0.1.0.0
      - oracle-server(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.5.245.4.0.1.0.0

Application Group: email
    Number of Protocols: 7
      - smtp
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.25.4.0.1.0.0
      - smtps
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.1.209.4.0.1.0.0
      - pop3(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.0.110.4.0.1.0.0
      - pop3(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.110.4.0.1.0.0
      - pop3s
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.3.227.4.0.1.0.0
      - imap2
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.143.4.0.1.0.0
      - imaps
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.3.225.4.0.1.0.0

Application Group: Multi-Media
    Number of Protocols: 9
      - h225
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.6.184.4.0.1.0.0
      - h245
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.6.182.4.0.1.0.0
      - h323-gatekeeper
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.6.183.4.0.1.0.0
      - rtp
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.125.0.4.0.1.0.0
      - rtcp
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.125.1.4.0.1.0.0
      - sip(udp)
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.19.196.4.0.1.0.
      - sip(tcp)
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.19.196.4.0.1.0.0
      - mgcp
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.9.123.4.0.1.0.0
      - sccp
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.7.208.4.0.1.0.0

Related Commands

application

show audit-trail

To display the audit trail configuration, use the show audit-trail command.

show audit-trail

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the audit trail configuration:

root@hostname.cisco.com# show audit-trail
Audit trail is enabled.
root@hostname.cisco.com# 

Related Commands

audit-trail enable

show autocreate-data-source

To display the autocreated data-sources, use the show autocreate-data-source command.

show autocreate-data-source

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows if the autocreation of data-sources feature is enabled:

root@NAM.cisco.com# show autocreate-data-source

NDE autocreation    : ENABLED
WAAS autocreation   : ENABLED
ERSPAN autocreation : ENABLED

Autocreate WAAS Client data source     : ENABLED
Autocreate WAAS Client WAN data source : DISABLED
Autocreate WAAS Server WAN data source : DISABLED
Autocreate WAAS Server data source     : DISABLED
Autocreate WAAS Passthru data source   : DISABLED

Enable Passthru export on autocreated WAAS device : NO

root@NAM.cisco.com#

show cdb

To display information about a CDB file, use the show cdb command.

show cdb [filename]

Syntax Description

filename

Specifies the CDB filename.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all platforms.


show cdp settings

To display the current Cisco Discovery Protocol (CDP) settings, use the show cdp settings command.

show cdp settings


Note This command is not supported on NAM-1 or NAM-2 devices or the NAM Virtual Blade.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on NME-NAM-80S and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.

Examples

To display the current CDP settings:

root@nam# show cdp settings
CDP is disabled
    Message Interval:   60
    Message Hold Time:  180

root@nam#

Related Commands

autocreate-data-source
cdp hold-time
cdp interval

show certificate

To display the installed certificate, use the show certificate command.

show certificate

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display certificate information:

Root@localhost# show certificate
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----

Related Commands

show certificate-request

show certificate-request

To display the certificate-signing requests, use the show certificate-request command.

show certificate-request

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to display the certificate-signing requests:

Root@localhost# show certificate-request

Related Commands

show certificate