Cisco Prime Network Analysis Module 5.1 Command Reference
NAM CLI Commands: application - device waas
Downloads: This chapterpdf (PDF - 226.0KB) The complete bookPDF (PDF - 2.31MB) | Feedback

NAM CLI Commands: application - device waas

Table Of Contents

NAM CLI Commands:
application - device waas

application

application group

audit-trail enable

autocreate-data-source

cdp enable

cdp hold-time

cdp interval

clear access log

clear captured-data-files

clear monitoring-data

clear system-alerts

clock set

config clear

config network

config upload

coredump

data-source erspan

data-source netflow

data-source pa

data-source waas

debug log disable

debug log enable

debug log level

debug log metric-engine

debug log reset

device erspan

device netflow

device waas


NAM CLI Commands:
application - device waas


This chapter contains an alphabetical listing of the commands unique to the Catalyst 6500 series and Cisco 7600 series Network Analysis Module (NAM), Cisco NAM 2200 Series appliances, Cisco Virtual Services Blade on WAAS appliances, Cisco Branch router series NME-NAM modules, and Cisco SRE NAM modules.

For information about Cisco IOS commands that are used to configure the switch, see the current Cisco IOS documentation including:

Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.1E/native/
configuration/guide/swconfig.html

Catalyst 6500 Series Switch Cisco IOS Software Command References

http://www.cisco.com/en/US/products/hw/switches/ps708/prod_command_reference_list.html

Each command lists whether it is specific to a NAM platform or if a NAM platform is excepted. Unless otherwise noted, commands are valid for all network analysis modules.

For ease of use, NAM CLI Commands, is divided into six different chapters:

NAM CLI Commands: application - device waas (this chapter)

NAM CLI Commands: email - managed device community

NAM CLI Commands: metric export host - show certificate request

NAM CLI Commands: show clock details - show monitor urlfilter

NAM CLI Commands: show patches - web user

This chapter describes the following commands:

application

application group

audit-trail enable

autocreate-data-source

cdp enable

cdp hold-time

cdp interval

clear captured-data-files

clear monitoring-data

clock set

config clear

config network

config upload

coredump

data-source erspan

data-source netflow

data-source pa

data-source waas

debug log disable

debug log enable

debug log level

debug log metric-engine

debug log reset

device erspan

device netflow

device waas

application

To create an application, use the application command. To remove an application match, use the no application command.

application

no application

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the application submode, the following commands are available:

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command section.

help—Displays help and keeps you in the application subcommand mode; see the "help" command section.

matchSpecifies a protocol and one port or port range. Repeat "match" command if there is more than one protocol or ports need to be include in this user defined protocol.

name string—Sets the the application name. This is a mandatory field.

Examples

This example shows how to create an application :

root@NAM# application
new application (app tag 268435459)
Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@NAM(sub-application)# ?
?                         - display help
cancel                    - discard changes and exit from subcommand mode
exit                      - exit from the subcommand mode
help                      - display help
match                     - specify an application match
name                      - enter the application name (*)
no                        - remove an application match

(*) - denotes a mandatory field for this configuration.

root@NAM(sub-application)#

application group

To enter the application group submode and define an application group, use the application group command. To remove an application group, use the no form of this command.

application group

no application group group-name

Syntax Description

group-name

Application group name.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the application group submode, the following commands are available:

add protocol-specifierAdds a protocol to the group. You only can add one protocol to a group at a time (for example, HTTPS). This command allows you to group statistics for more than one specified protocol into one counter.

To add two or more protocols to an application group, repeat the add command for each protocol. The protocols are added only when you exit application group subcommand mode.

cancel—Discards changes and exits from the subcommand mode.

delete protocol-specifierRemoves a protocol from the group. You only can remove one protocol from a group at a time.

To remove two or more existing protocols from an existing application group, repeat the delete command for each protocol. The protocol is removed only when you exit the application group subcommand mode.

exit—Saves changes and exits from the subcommand mode.

help—Displays help and keeps you in the application group subcommand mode.

name string—Sets the the application group name.

You must provide protocol specifiers in the add or delete parameters, or both the add and delete parameters.

Examples

This example shows how to create an application group named appGrpSample with two protocols in the group:

root@NAM# application group
Entering into subcommand mode for this command.
Type 'exit' to come out of this mode.
Type 'cancel' to discard changes and to come out of this mode.
root@NAM(sub-application-group)# ?
?                         - display help
add                       - add a protocol to the group (*)
cancel                    - discard changes and exit from subcommand mode
delete                    - remove a protocol from the group (*)
exit                      - exit from subcommand mode
help                      - display help
name                      - set application group name (*)

(*) - denotes a mandatory field for this configuration.
root@NAM(sub-application-group)# add 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.3.68.4.0.1.0.0
root@NAM(sub-application-group)# add 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.4.60.4.0.1.0.0
root@NAM(sub-application-group)# name appGrpSample
root@NAM(sub-application-group)# exit
Sucessfully create application group appGrpSample.
root@NAM#
root@NAM#
root@NAM# show application group appGrpSample
Application Group: appGrpSample
    Number of Protocols: 2
      - w-ether2.ip.tcp.tcp-836
        16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.3.68.4.0.1.0.0
      - w-ether2.ip.udp.udp-1084
        16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.4.60.4.0.1.0.0

root@NAM#

Related Commands

show application group

audit-trail enable

To enable and audit trail of GUI and CLI accesses, use the audit-trail enable command. To disable audit trail of GUI and CLI accesses, use the no form of this command.

audit-trail enable

no audit-trail enable

Defaults

Audit trail of the CLI and GUI accesses is enabled.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to enable an audit trail for GUI and CLI accesses:

root@hostname.cisco.com# audit-trail enable

Related Commands

show audit-trail

autocreate-data-source

To enable autocreation of the data-source, use the autocreate data-source command. To disable autocreation of data-sources on NAM, use the no form of this command.

autocreate data-source

no autocreate data-source

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms..

Examples

This example shows how to enable autocreation of data-sources:

root@nam235Cat6k.cisco.com# autocreate-data-source ?
erspan                    - enable autocreation of ERSPAN data sources
netflow                   - enable autocreation of NDE data sources
waas                      - enable autocreation of WAAS data sources
waas-client               - enable autocreation of WAAS Client data sources
waas-client-wan           - enable autocreation of WAAS Client WAN data sources
waas-passthru             - enable autocreation of WAAS Passthru data sources
waas-passthru-export      - enable Passthru export on autocreated WAAS devices
waas-server               - enable autocreation of WAAS Server data sources
waas-server-wan           - enable autocreation of WAAS Server WAN data sources
root@nam235Cat6k.cisco.com# autocreate-data-source 

cdp enable

To enable the Cisco Discovery Protocol (CDP) on the NME-NAM, use the cdp enable command. To disable CDP on the NME-NAM, use the no form of this command.

cdp enable

no cdp enable


Note This command is not valid for NAM-1 or NAM-2 devices, the Cisco NAM 2200 Series appliances, or NAM Virtual Blades.


Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on the NME-NAM-80S and NME-NAM-120S.

Examples

This example shows how to enable CDP:

root@localhost.cisco.com# cdp enable
root@localhost.cisco.com#

Related Commands

cdp hold-time
cdp interval
show cdp settings

cdp hold-time

To set the Cisco Discovery Protocol (CDP) messages hold time, use the cdp hold-time command. To return the CDP messages hold time to the default value, use the no form of this command.

cdp hold-time time

no cdp hold-time


Note This command is not valid for NAM-1 or NAM-2 devices or the Cisco NAM 2200 Series appliances.


Syntax Description

time

Specifies the CDP hold time. Range is from 10 to 255 seconds.


Defaults

180 seconds.

Command Modes

Command mode

Examples

This example shows how to set the CDP messages hold time:

root@localhost.cisco.com# cdp hold-time 30
root@localhost.cisco.com#

Related Commands

cdp enable
cdp interval
show cdp settings

cdp interval

To set the Cisco Discovery Protocol (CDP) messages interval on the NME-NAM, use the cdp interval command. To return the CDP messages interval on the NME-NAM to the default value, use the no form of this command.

cdp interval time

no cdp interval


Note This command is not valid for NAM-1 or NAM-2 devices or the Cisco NAM 2200 Series appliances.


Syntax Description

time

Specifies the CDP messages interval. Range is from 5 to 254 seconds.


Defaults

60 seconds

Command Modes

Command mode

Examples

This example shows how to set the CDP messages interval:

root@localhost.cisco.com# cdp interval 200
root@localhost.cisco.com#

Related Commands

cdp enable
cdp hold-time
show cdp settings

clear access log

To clear the access log, use the clear access log command.

clear access-log

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to clear the access log:

root@localhost# clear access-log

Related Commands

show access-log

clear captured-data-files

To delete all captured files from the NAM local hard drive, use the clear captured-data-files command.

clear captured-data-files

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to delete all captured files:

root@localhost# clear captured-data-files

clear monitoring-data

To delete both short term and long term monitoring data, use the clear monitoring-data command. This command will also reset NAM to clean up cached data.

clear monitoring-data

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to clear the access log:

root@localhost# clear monitoring-data

clear system-alerts

To clear the system alerts, use the clear system-alerts command.

clear system-alerts

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to clear the system alerts:

root@localhost# clear system-alerts

Related Commands

show system-alerts

clock set

To set the date and time of a Cisco NAM 2200 series appliance, use the clock set command.

clock set <hh:mm:ss:> <mm/dd/yyyy>


Note This command is only valid for Cisco NAM 2200 series appliances.


Syntax Description

hh:mm:ss:

hh=hour, mm=minutes, ss=seconds

mm/dd/yyyy

mm = month, dd=day, yyyy=year


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported only on the Cisco NAM 2200 Series appliances.

Examples

The following example shows how to set the clock on the NAM appliance.

root@nam.cisco.com# clock set 06:10:00 08/04/2008

config clear

To reset the NAM and return it to the factory-default state, use the config clear command.

config clear [all | ip]

Syntax Description

all

(Optional) Resets the NAM to the factory-default state including the NAM IP parameters configuration. The NAM reboots automatically for the changes to take effect.

ip

(Optional) Resets the NAM IP parameters to the manufacturing-default state. The NAM reboots automatically, and you must session into the NAM from the switch supervisor engine to configure the NAM IP parameters so that the module can come online.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to clear the configuration:

root@localhost# config clear
This operation will reset the NAM configuration with the exception
of NAM IP parameters.

This operation will also reboot the NAM to allow the changes to
take effect.

Do you wish to continue? (y/n) [n]:y
Successfully updated the SCCP configuration.
Successfully updated the H.323 configuration.
NAM syslog settings updated successfully.
NAM web interface preferences updated successfully.

Successfully modified the configuration.
NAM will be rebooted now, for the changes to take effect ...

config network

To import a NAM configuration into the NAM from a specified location or to restore a NAM Virtual Blade license, use the config network command.

config network url [config_filename]

Syntax Description

url

Specifies the location of the configuration or license file to upload;
ftp://<username>@<host>/<path>

config_filename

Specifies the filename for the configuration file.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to download a configuration file to a NAM named kluu-test.config, which is located at the FTP server namlab-pc1 in the user home directory named /home/kluu directory.

root@NAM #
root@NAM # config network ftp://kluu@namlab-pc1//home/kluu/kluu-test.config
Downloading ftp://kluu@namlab-pc1//home/kluu/kluu-test.config, please wait ...

Password for kluu@namlab-pc1:
ftp://kluu@namlab-pc1//home/kluu/kluu-test.config (9K)
/tmp/lrcfile.txt.1007     [########################]       9K | 4916.90K/s
9748 bytes transferred in 0.00 sec (4274.44k/sec)

Download completed.

Configuring the NAM. This may take few minutes, please wait ...

NAM configuration completed.
To view the results, use the command 'show log config'.
root@NAM #

Related Commands

config upload


config upload

To upload the running NAM configuration to a specified location, use the config upload command.

config upload url [config_filename]

Syntax Description

url

Specifies the location of the configuration or license file to upload;
ftp://<username>@<host>/<path>

config_filename

Specifies the filename for the configuration file.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms. If config_filename is not specified when this command is issued, NAM will assign a default config file name.

Examples

This example shows how to upload the NAM running configuration to the FTP server named namlab-pc1 with a filename of example.config:

root@NAM# config upload ftp://kluu@namlab-pc1.cisco.com example.config
Building configuration, please wait... Done.

Uploading the configuration to 'example.config'
on 'ftp://kluu@namlab-pc1.cisco.com', This may take few minutes ...

Password:

Successfully uploaded the NAM configuration.
root@NAM#

Related Commands

config network

coredump

To retrieve the core dump file, use the coredump command.

coredump ftp://user:passwd@host/full-path/

Syntax Description

ftp://user:passwd@host/full-path/

Sets the path to the core dump file.


Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

This example shows how to retrieve a core dump:

root@localhost# coredump ftp://user:passwd@host/full-path/

data-source erspan

To create ERSPAN (Encapsulated Remote SPAN) data-source, use the data-source erspan command.

data-source erspan

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the data-source erspan submode, the following commands are available:

device-id—ERSPAN device ID. This is a mandatory value.

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command section.

help—Displays help and keeps you in the application group subcommand mode; see the "help" command section.

name string—Sets the data-source erspan name. This is a mandatory value.

session-idERSPAN session ID

showShows the current configuration which is applied on exit

Examples

This example shows how to create an ERSPAN data-source:


root@nam235Cat6k.cisco.com# data-source erspan
Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-data-source-erspan)# ?
?                         - display help
cancel                    - discard changes and exit from subcommand mode
device-id                 - ERSPAN device ID (*)
exit                      - create data-source and exit from sub-command mode
help                      - display help
name                      - data-source name (*)
session-id                - ERSPAN session ID
show                      - show current config that will be applied on exit

(*) - denotes a mandatory field for this configuration.

data-source netflow

To create NetFlow Data Export (NDE) data-source, use the data-source netflow command.

data-source netflow

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the data-source netFlow submode, the following commands are available:

device-id—NetFlow device ID. This is a mandatory value.

engine-id—NetFlow engine ID

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode.

help—Displays help and keeps you in the application group subcommand mode.

name string—Sets the netFlow data-source name. This is a mandatory value.

showShows the current configuration which is applied on exit

Examples

This example shows how to create a netFlow data-source:

root@nam235Cat6k.cisco.com# data-source netflow 

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-data-source-netflow)# ?
?                         - display help
cancel                    - discard changes and exit from subcommand mode
device-id                 - netflow device ID (*)
engine-id                 - netflow Engine ID
exit                      - create data-source and exit from sub-command mode
help                      - display help
name                      - data-source name (*)
show                      - show current config that will be applied on exit

(*) - denotes a mandatory field for this configuration.

data-source pa

To create performance agent (pa) data-source, use the data-source pa command.

data-source pa

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the data-source netFlow submode, the following commands are available:

device-id—NetFlow device ID. This is a mandatory value.

engine-id—NetFlow engine ID

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode.

help—Displays help and keeps you in the application group subcommand mode.

name string—Sets the netFlow data-source name. This is a mandatory value.

showShows the current configuration which is applied on exit

Examples

This example shows how to create a pa data-source:

root@nam235Cat6k.cisco.com# data-source pa 

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-data-source-netflow)# ?
?                         - display help
cancel                    - discard changes and exit from subcommand mode
device-id                 - netflow device ID (*)
engine-id                 - netflow Engine ID
exit                      - create data-source and exit from sub-command mode
help                      - display help
name                      - data-source name (*)
show                      - show current config that will be applied on exit

(*) - denotes a mandatory field for this configuration.

data-source waas

To create Wide Area Application Services (WAAS) data-source, use the data-source waas command.

data-source waas

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the data-source waas submode, the following commands are available:

device-id—WAAS device ID. This is a mandatory value.

segmentThis is the network segment that needs to be added to the data-source. This is a mandatory value.

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command section.

help—Displays help and keeps you in the application group subcommand mode; see the "help" command section.

name string—Sets the waas data-source name. This is a mandatory value.

showShows the current configuration which is applied on exit.

Examples

This example shows how to create a WAAS data-source:

root@nam235Cat6k.cisco.com# data-source waas

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-data-source-waas)# ?
?                         - display help
cancel                    - discard changes and exit from subcommand mode
device-id                 - WAAS device ID (*)
exit                      - create data-source and exit from sub-command mode
help                      - display help
name                      - data-source name (*)
segment                   - network segment to be added to data-source (*)
show                      - show current config that will be applied on exit

(*) - denotes a mandatory field for this configuration.

debug log disable

To disable debug logging, use the debug log disable command.

debug log disable

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default behavior or settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example disables all debug logging:

root@nam.cisco.com# debug log disable

debug log enable

To enable debug logging, use the debug log enable command.

debug log enable

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default behavior or settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example enables all debug logging:

root@nam.cisco.com# debug log enable

debug log level

To set the debug log level for each module running in NAM system, use the debug log-level command.

show debug log level <log-feature> <log-level>

Syntax Description

log-feature

Possible feature names include the following:
ART, CAPTURE, CDP, COLL_SHARED, DSMON_HOST, DSMON_MATRIX, DSMON_PDIST, DSMON_STATS, ENTITY, ETHERSTATS, FM, FR, MAIN, MISC, RMON, RPC, DSRC, PARSER, PPROC, RTP, METRIC_ENGINE, OTHER, PORT_TABLE, MPLS_STATS, POLLD, RMON1_HOST, RMON1_MATRIX, RMON2_ADDRMAP, RMON2_HOST, RMON2_MATRIX, RMON2_PDIST, SMON_PRIO, SMON_VLAN, SNMP, SRSNMP, SWPOLLD, TREND_DAEMON, TREND_RPC, TREND_SNMP, URL_COLLECTION, WAAS,

log-level

A value between 0 and 7 which represents the following log levels:

0—Critical
1—Error
2—Warning
3—Notice
4—Info
5—Debug
6—Debug2
7—Debug3


Defaults

This command has no default behavior or settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example shows how to set the automated response time (ART) feature to display all log messages up to log level 2. This command will log all messages generated by the ART module that have log levels set to critical, error, and warning.

root@nam.cisco.com# debug log level ART 2

debug log metric-engine

To set debug log metric-engine, use the debug log metric-engine command.

debug log metric-engine

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example sets the debug log level metric-engine:

root@nam.cisco.com# debug log metric-engine

debug log reset

To reset debug logging level back to default settings, use the debug log reset command.

debug log reset

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

Examples

The following example resets all debug log levels back to default values:

root@nam.cisco.com# debug log reset

device erspan

To create an ERSPAN (Encapsulated Remote SPAN) device, use the device erspan command.

device erspan

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the device erspan submode, the following commands are available:

address—IP address of the device. This is a mandatory value.

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command section.

help—Displays help and keeps you in the application group subcommand mode; see the "help" command section.

showShows the current configuration which is applied on exit

Examples

This example shows how to create an ERSPAN device:


root@nam235Cat6k.cisco.com# device erspan

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-device-erspan)# ?
?                         - display help
address                   - device IP address (*)
cancel                    - discard changes and exit from subcommand mode
exit                      - create device and exit from sub-command mode
help                      - display help
show                      - show current config that will be applied on exit

(*) - denotes a mandatory field for this configuration.

device netflow

To create a NetFlow Data Export (NDE) device, use the device netflow command.

device netflow

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the device netFlow submode, the following commands are available:

address—IP address of the device. This is a mandatory value.

communitySNMPv2c community string

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command section.

help—Displays help and keeps you in the application group subcommand mode; see the "help" command section.

showShows the current configuration which is applied on exit.

snmp-versionThe version of SNMP that is used to communicate with the device

v3-auth-passphraseSNMPv3 authentication passphrase

v3-auth-protocolSNMPv3 authentication protocol

v3-priv-passphraseSNMPv3 privacy passphrase

v3-priv-protocolSNMPv3 privacy protocol

v3-sec-levelSNMPv3 security level

v3-usernameSNMPv3 username

Examples

This example shows how to create a netFlow device:

root@nam235Cat6k.cisco.com# device netflow

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-device-netflow)# ?
?                         - display help
address                   - device IP address (*)
cancel                    - discard changes and exit from subcommand mode
community                 - SNMPv2c community string
exit                      - create device and exit from sub-command mode
help                      - display help
show                      - show current config that will be applied on exit
snmp-version              - SNMP version to use to communicate with device
v3-auth-passphrase        - SNMPv3 authentication passphrase
v3-auth-protocol          - SNMPv3 authentication protocol
v3-priv-passphrase        - SNMPv3 privacy passphrase
v3-priv-protocol          - SNMPv3 privacy protocol
v3-sec-level              - SNMPv3 security level
v3-username               - SNMPv3 username

(*) - denotes a mandatory field for this configuration.

device waas

To create Wide Area Application Services (WAAS) device, use the device waas command.

device waas

Defaults

This command has no default settings.

Command Modes

Command mode

Usage Guidelines

This command is supported on all NAM platforms.

When you enter the device WAAS submode, the following commands are available:

address—IP address of the device. This is a mandatory value.

passthruThis is the passthru enable or disable traffic from the WAAS device.

cancel—Discards changes and exits from the subcommand mode.

exit—Saves changes and exits from the subcommand mode; see the exit command section.

help—Displays help and keeps you in the application group subcommand mode; see the "help" command section.

showShows the current configuration which is applied on exit.

Examples

This example shows how to create a WAAS device:

root@nam235Cat6k.cisco.com# device waas

Entering into subcommand mode for this command.
Type 'exit' to apply changes and come out of this mode.
Type 'cancel' to discard changes and come out of this mode.

root@nam235Cat6k.cisco.com(sub-device-waas)# ?
?                         - display help
address                   - device IP address (*)
cancel                    - discard changes and exit from subcommand mode
exit                      - create device and exit from sub-command mode
help                      - display help
passthru                  - enable/disable passthru traffic from WAAS device
show                      - show current config that will be applied on exit

(*) - denotes a mandatory field for this configuration.