This section lists the new features/functionality delivered in Cisco EPN Manager 6.0.0.

Note	Following features are deprecated in Cisco EPN Manager 5.1 and will be removed from Cisco EPN Manager 6.1: Deprecation of browser (Internet Explorer 11 - IE11) Deprecation of Bare metal installation Deprecation of classic license

Note	MTOSI support for EPNM has been deprecated from Cisco EPN Manager 3.1 onwards, please use RESTconf NB APIs for integration.

Note	IoT feature and device support has been deprecated from Cisco EPN Manager 4.1 onwards and removed from Cisco EPN Manager 5.0 onwards.

Note	Cable devices and functionality has been deprecated from Cisco EPN Manager 4.0.1 onwards and removed from Cisco EPN Manager 5.0 onwards.

Note	Features marked “BETA” provide limited functionality in this release. The intention is to fully support these features in the next release.

Note	NBI Credential user group is deprecated starting Cisco EPN Manager 4.0 release.

Note	G8032 is not supported and has been deprecated starting Cisco EPN Manager 4.0 release.

GUI - General

• Support for software upgrade for NCS540 FPD

• Support for NCS2k SVO 12.3 SW Upgrade

Device Configuration

• NCS2k SVO reports for T6 TXP

• Router Inventory to show SFP Type at interface/port - Copper/Optical

Circuit Emulation

• Support EVPN Multi-Homed VPWS in EPN-M: Faults and Y.1731/1564

Device Support

• EPNM support of NCS 2k 12.3 on NCS 2000

• EPNM support of IOS-XR  7.4.1 on ASR9K

Optical

• Support for SMR1/2 with NCS2KSVO 12.3 version

• Support for NCS2K SVO 12.3 version

• OCH-Trail WSON migration support for OTU3/OTU2/OTU2E /OTU4/OTU4C2


• OCH-CC WSON migration support for 100G/10G/40G

• Support of OTU2-XP TXP with 10GE CC rate & OTU2E Trail rate with version NCS2K SVO 12.2 and above

• Support of PSM with version NCS2K SVO 12.3

• Support of BSTE-AMP17 with version NCS2K SVO 12.3

• Support of 150G OCH trail for NCS55-6X200-DWDM line card

• Support of NCS1004, NCS2k SVO with IPv6 DCN

• Support for Manged Plane OCH-NC provisioning & discovery for NCS2K SVO

• Support of NCS2K-RAMAN-CTP-C+L  Amplifier - Ornellaia with version NCS2K SVO 12.3

• Support of NCS1004 Rel 7.2.1 with features:


  BPSK support on trunk with 50G rate


  FEC Enhanced SD-15


  FR and DAC QSFP support along with Performance Metrics


  MAC address snooping

• NCS2k SVO licensing

• NCS2k SVO reports for T6 transponder (TXP)

Fault Management

• Suppress warning level trap notifications for the entitysensorthreshold alarm on EPNM

Service Discovery

• Support for Segment Routing on IOS XE (17.4.1 as minimum version)

This section lists the features/functionality/Menus deprecated in Cisco EPN Manager 6.0.0.

• Topology Map functionality:

  1. Grouping settings under system Settings

  2. Hover information on links in Topology

  3. Print\Save of map

  4. Map dashlet

• General Features:

  1. Chassis View consolidation: always ON chassis view with merged logical and device details view

  2. Active Virtual Domain

• Administration>Dashboards​> Job Dashboard> System Jobs - APIC-EM Integration

• Administration>Dashboards​> Job Dashboard>System Jobs - Assurance & Health summary​

• Administration>Dashboards​> Job Dashboard> System Jobs - Wirecless Monitoring

• Administration>Servers> ACS View Servers>ACS View Servers

• Administration>Servers> APIC-EM Controller​> APIC-EM Controller​

• Administration>Settings>Logging>SNMP Log

• Administration>Settings>Logging>Syslog

• Administration>Settings>Certificate> Certificate - System Key & Certificate

• Administration>Settings> System Audit​> System Audit​

• Administration>Settings> System Settings> General - Guest Account​

• Administration>Settings> System Settings> General - Help Us Improve​

• Administration>Settings> System Settings> General - Proxy

• Administration>Settings> System Settings> General - Software Request​

• Administration>Settings> System Settings>General - Cisco DNAC Center​

• Administration>Settings> System Settings> Network & Device - CLI Session​

• Administration>Settings> System Settings> Network & Device - Controller Upgrade

• Administration>Settings> System Settings> Network & Device - Unified AP Ping Reachability​

• Administration>Settings> System Settings> Network & Device - Plug & Play​

• Administration>Settings> System Settings> Switch Port Trace - Auto SPT​

• Administration>Settings> System Settings> Switch Port Trace - Manual SPT​

• Administration>Settings> System Settings> Switch Port Trace - SPT Configuration

• Administration>Settings> System Settings> Switch Port Trace - Known Ethernet MAC​

• Administration>Settings> System Settings> Inventory - Datacenter Settings​

• Administration>Settings> System Settings> Client & User - All sub menu​

• Administration>Settings> System Settings> Services - Service Container Management

• Configuration> Templates​> Features and Technologies> Feature Templates

• Configuration> Templates> Switch Location​> Switch Location Table view

• Configuration> Templates> Switch Location​> Switch Location - Add Template​

• Configuration> Templates> Switch Location​> Switch Location - Apply Template

• Configuration> Templates> Scheduled Configuration Task>​ AP Template Tasks

• Configuration> Templates> Scheduled Configuration Task​> AP Template

• Configuration> Templates> Scheduled Configuration Task​> Config Group​

• Configuration> Templates> Scheduled Configuration Task​> WLAN Configuration

• Configuration> Templates> Scheduled Configuration Task​> Download Software

• Dashboard​> Performance> BNG Statistics> BNG Statistics Dashboard TAB​

• Dashboard​> Performance> ME1200 QoS​> ME1200 QoS Dashboard TAB​

• Dashboard​> Device Trends> Applications​> Applications Trend Dashboard​

• Inventory>Device Management>Device Details>Device Details - CDP Neighbours

• Inventory>Device Management>Device Details>Device Details - Civic Location​

• Inventory>Device Management>Device Details>Device Details - Spanning Tree

• Inventory>Device Management>Device Details>Device Details - VTP

• Inventory>Device Management>Device Details>Device Details - Stacks

• Inventory>Device Management>Device Details>Device Details – VLANs

• Inventory>Device Management>Device Details>STS/VC Interfaces​

• Inventory>Device Management>Device Details>Intra Node LMP​

• Inventory>Device Management> Configuration Archive> Config Archive Device Table - Deploy Config​

• Inventory>Device Management>Virtual Image Repository​> Image Repository View

• Inventory>Device Management> Network Audit> Deprecated - To be removed​

This section lists the new support provided in Cisco EPN Manager 6.0.0. For a list of all support information, click the gear icon at the top right of the web GUI and choose Help > Supported Devices.

Note	“BETA” means that the device/operating system has not yet been released but Cisco EPN Manager has been tested on the Beta version.

Cisco NCS 2000 Series Network Convergence Systems —New Operating System Support

Device Model	Device OS
Cisco NCS 2000	NCS 2K 12.3

Cisco ASR 9000 Series Aggregation Services Routers—New Operating System Support

Device Model	Device OS
Cisco ASR 9000 Router	IOS-XR 7.4.1

Note	IOS-XR 7.1.3 is not supported on Cisco ASR 9903 router.

The following table lists the valid paths for installing/upgrading to Cisco EPN Manager 6.0.0 from previous versions.

See the relevant installation guide for installation prerequisites and procedures for Cisco EPN Manager versions.

For point patch installation instructions, see the readme file supplied with the patch file on the on the Software Download site on Cisco.com.

Cisco EPN Manager software is distributed with all the components necessary for its optimized and secure operation, including the Red Hat Linux operating system and the Oracle database. All security-related configurations, regression testing, performance, and scalability metrics are based on the set of components and configurations included in the original Cisco EPN Manager software distribution. Cisco provides periodic EPN Manager software updates that can also contain necessary updates to the packages installed on the operating system or to the database.

Note that if any of the following changes are made to the original distributed Cisco EPN Manager software, Cisco will no longer support the operating environment:

• Configuration changes to the software or operating system, or installation of other components that are not part of the original distribution.

• Direct installation and application of third-party software on the Red Hat Linux operating system embedded within Cisco EPN Manager.

• Application of updates or patches that are not provided by Cisco to individual Cisco EPN Manager components.

• Changes to the internal Cisco EPN Manager settings that are not documented as modifiable in the Cisco EPN Manager User and Administrator Guide on Cisco.com, as these changes may weaken security, disable functionality, or degrade scalability and performance.

Upgrade Issues

• FTP and TPTP is disabled by default.

• Active Threshold Crossing Alarms (TCA) for temperature remain active and are not cleared automatically. Please clear these alarms manually.

• You must resync your devices to view ISIS links.

• You must resync LDP-enabled devices to view LDP feature-related information.

• You must recreate the TCAs for inbound/outbound errors and inbound/outbound discards in the Interface Health monitoring policy.

Limitations on Carrier Ethernet Circuit Provisioning

• Promotion of service using old probe name format is now supported. These probes are listed in user interface with appropriate standard OAM Profile name after promotion.

• Sample profile: profile PM2_3_8_CoS5_DM type cfm-delay-measurement.

• While custom profile names are supported in EPN Manager, modifying brownfield services with a different naming format deletes the existing custom profile and adds a new profile with a supported naming format.

• Inventory models do not correctly display the profiles that are not associated to a service.

• Validation limit for number of profiles is 100. If you create a new SLA operation profile after 100 existing profiles, the device generates an error and deployment fails.

TLS 1.2 Required for Secured Channel Communication for HTTPS and TLS

Only Transport Layer Security (TLS) 1.2 is supported for HTTPS and TLS related secured communication, for example, RADIUS EAP-TLS.

Support for TLS 1.0, TLS 1.1, and all versions of SSL has been disabled due to security vulnerabilities.

This means that all peer systems and clients that transact with Cisco EPN Manager using HTTPS/TLS must support TLS 1.2. If they do not support TLS 1.2, you must upgrade these systems. Wherever possible, the Cisco EPN Manager documentation highlights the potentially affected systems. Please contact your Cisco representative for support in this regard, if necessary.

Reconciliation Report Limitations

If you have not provided a value for an attribute while provisioning a service, the provisioned value for that attribute is displayed as “Missing” in the reconciliation report. The device may have a default value for this attribute, but Cisco EPN Manager does configure this value.

Limitations on ME 1200 Devices

The Y.1564 performance test does not work if the source/destination is a ME 1200 device.

Limitations on Editing Alarm Notification Policies

If the upgrade conditions of existing categories are different from the condition of categories on 5.1, then the conditions post upgrade will not match. As a result, policy might not be created or UI selection might not take place for the unmatched events. In this case, you should delete the upgraded policies and create a new one.

Limitations on NCS 4200 Devices Running IOS-XE 16.8.1

The following functionalities do not work on NCS 4200 devices running IOS-XE 16.8.1:

• Alarm profile

• Configuration of SONET LOP and CT3 LOP from the GUI

• Admin shut/no shut functionality on SONET/T1/T3 HOP/LOP

Limitations on NCS540 and NCS5500 devices

• NCS540 and NCS5500 device series does not support Fault-OAM, Wrap-Protection and BFD.

Use CLI Templates for Configuring PTP Commands

On ASR920 devices with software version 16.9.1, IEEE 1588-2008 BC/MC license is required to execute the 1588 PTP commands.

Configuration and Inventory Not Supported for PTP Templates

The behavior of modeling the configurations pushed through PTP templates may not work as expected because the model may not be in place for all the configurations pushed through PTP templates. Configuration/Inventory is not supported for these configurations.

Deprecation of Support for ONS 10.00.10, 10.01.00, 10.03.00

ONS 10.00.10, 10.01.00, 10.03.00 ONS 10.00.10, 10.01.00, and 10.03.00 are no longer supported on Cisco NCS 2002, 2006 and 2015 devices.

Data Center Device Lifecycle Support Only

Cisco EPN Manager provides foundation lifecycle support for UCS compute systems, CSR 1000v, and Nexus series devices but does not provide data center topology.

LINK_DOWN alarm on sub interfaces in Gig Port

LINK_DOWN alarms will not be generated when link is down on sub interfaces in a Gig Port.

Limitations on Carrier Ethernet Circuit Provisioning

• Limitations for EVPN Multi-Homed VPWS in EPNM (Beta level).

• No new syslogs support added for EVPN Multi-Homed. Workaround - Full sync of devices needed.

• Serviceability state will be shown as Partial for Port-Active and Single-Active.

• Serviceability state calculation logic is not yet changed for multihoming.

• In case of partial configuration of EVPN Multi-Homed (For example, two A-end devices are configured), the service is discovered as two different services with one endpoint each, in Circuit VC.

• There is no differentiation for EthernetSegment used for Single-Homed or Multi-Homed in overlay.

• SR-TE ODN not supported in EPNM for EVPN Multi-Homed discovery.

• Open Bugs

• Closed Bugs

• Resolved Bugs

• Get Information about Cisco EPN Manager Bugs

For a list of all documentation available for Cisco EPN Manager 6.0.0, see the Cisco Evolved Programmable Network Manager 6.0 Documentation Overview.

For a list of accessibility features in Cisco EPN Manager 6.0.0, please contact accessibility@cisco.com.

All product documents are accessible. If you would like to receive the product documentation in audio format, braille, or large print, contact accessibility@cisco.com

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation

Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation, as an RSS feed and deliver content directly to your desktop using a reader application. The RSS feeds are a free service.