Cisco Transport Manager User's Guide, 9.2
Appendix C: Slot Property Information--Common, DWDM, Electrical, and Ethernet Cards
Downloads: This chapterpdf (PDF - 7.94MB) The complete bookPDF (PDF - 35.31MB) | Feedback

Slot Property Information—Common, DWDM, Electrical, and Ethernet Cards

Table Of Contents

Slot Property Information—Common, DWDM, Electrical, and Ethernet Cards

C.1  Common Cards

C.1.1  Slot Properties—AIC

C.1.2  Slot Properties—AIC-I

C.1.3  Slot Properties—CTX-2500

C.1.4  Slot Properties—CTX-CL600

C.1.5  Slot Properties—FILLER

C.1.6  Slot Properties—MIC-28-3-A and MIC-28-3-B

C.1.7  Slot Properties—MMU (ONS 15454 SONET and ONS 15454 SDH)

C.1.8  Slot Properties—OSCM (ONS 15454 SONET and ONS 15454 SDH)

C.1.9  Slot Properties—SSXC

C.1.10  Slot Properties—TCC+

C.1.11  Slot Properties—TCC-I

C.1.12  Slot Properties—TCC2

C.1.13  Slot Properties—TCC2P

C.1.14  Slot Properties—TSC (ONS 15600 SONET and ONS 15600 SDH)

C.1.15  Slot Properties—Unprovisioned Slot (ONS 15327 and ONS 15454 SONET)

C.1.16  Slot Properties—Unprovisioned Slot (ONS 15454 SDH)

C.1.17  Slot Properties—XC

C.1.18  Slot Properties—XC-VXL-10G

C.1.19  Slot Properties—XC10G

C.1.20  Slot Properties—XCVT

C.1.21  Slot Properties—XCVXC

C.1.22  Slot Properties—XTC (ONS 15305)

C.1.23  Slot Properties—XTC (ONS 15327)

C.1.24  Slot Properties—TNC

C.1.25  Slot Properties—TSC (ONS 15454 SONET and ONS 15454 SDH)

C.1.26  Slot Properties—TCC3

C.2  DWDM Cards

C.2.1  Slot Properties—2.5G_DM

C.2.2  Slot Properties—2.5G_DMP

C.2.3  Slot Properties—2.5G Multirate Transponder

C.2.4  Slot Properties—32DMX

C.2.5  Slot Properties—32DMX-L

C.2.6  Slot Properties—32DMX_O

C.2.7  Slot Properties—40-DMX-C

C.2.8  Slot Properties—32MUX_O

C.2.9  Slot Properties—40-MUX-C

C.2.10  Slot Properties—32WSS

C.2.11  Slot Properties—32WSS-L

C.2.12  Slot Properties—40-WSS-C

C.2.13  Slot Properties—40-WXC-C

C.2.14  Slot Properties—80-WXC-C

C.2.15  Slot Properties—40G-MXP-C

C.2.16  Slot Properties—4MD_xx.x

C.2.17  Slot Properties—AD_1B_xx.x

C.2.18  Slot Properties—AD_1C_xx.x

C.2.19  Slot Properties—AD_2C_xx.x

C.2.20  Slot Properties—AD_4B_xx.x

C.2.21  Slot Properties—AD_4C_xx.x

C.2.22  Slot Properties—ADM-10G

C.2.23  Slot Properties—GE_XP and 10GE_XP

C.2.24  Slot Properties—MXP_2.5G_10E

C.2.25  Slot Properties—MXP_2.5G_10G

C.2.26  Slot Properties—MXP_MR_10DME

C.2.27  Slot Properties—OPT-AMP-17-C and OPT-AMP-C

C.2.28  Slot Properties—OPT-AMP-L

C.2.29  Slot Properties—OPT-RAMP-C and OPT-RAMP-CE

C.2.30  Slot Properties—OPT-BST

C.2.31  Slot Properties—OPT-BST-E

C.2.32  Slot Properties—OPT-BST-L

C.2.33  Slot Properties—OPT-PRE

C.2.34  Slot Properties—OSC-CSM

C.2.35  Slot Properties—OTU2_XP

C.2.36  Slot Properties—PSM

C.2.37  Slot Properties—SMR-C

C.2.38  Slot Properties—T-DCU (TDC-CC and TDC-FC)

C.2.39  Slot Properties—TXP_MR_10E

C.2.40  Slot Properties—TXP_MR_10E_C

C.2.41  Slot Properties—TXP_MR_10G

C.3  Electrical Cards

C.3.1  Slot Properties—DS-1-14

C.3.2  Slot Properties—DS1-28/DS3-EC1-3

C.3.3  Slot Properties—DS1-84/DS3-EC1-3

C.3.4  Slot Properties—DS-1N

C.3.5  Slot Properties—DS-3-12

C.3.6  Slot Properties—DS-3E

C.3.7  Slot Properties—DS-3i

C.3.8  Slot Properties—DS-3i-N-12

C.3.9  Slot Properties—DS-3XM-6

C.3.10  Slot Properties—DS-N

C.3.11  Slot Properties—DS1_E1_56

C.3.12  Slot Properties—DS3_EC1_48

C.3.13  Slot Properties—DS3XM-12

C.3.14  Slot Properties—E-1

C.3.15  Slot Properties—E1_21_E3_DS3_3 and E1_63_E3_DS3_3

C.3.16  Slot Properties—E1-42

C.3.17  Slot Properties—E1-63 (ONS 15305 CTC)

C.3.18  Slot Properties—E1-8 (ONS 15305 CTC)

C.3.19  Slot Properties—E1-N-14

C.3.20  Slot Properties—E3-12

C.3.21  Slot Properties—E3T3_6 (ONS 15305 CTC)

C.3.22  Slot Properties—EC1-12

C.3.23  Slot Properties—FMEC-E3/DS-3

C.4  Ethernet Cards

C.4.1  Slot Properties—CE-100T-8 (ONS 15310 CL, ONS 15310 MA SONET, and ONS 15310 MA SDH)

C.4.2  Slot Properties—CE-100T-8 (ONS 15454 SONET)

C.4.3  Slot Properties—CE-100T-8 (ONS 15454 SDH)

C.4.4  Slot Properties—CE-1000-4 (ONS 15454 SDH and ONS 15454 SONET)

C.4.5  Slot Properties—CE-MR-6

C.4.6  Slot Properties—CE-MR-10

C.4.7  Slot Properties—E10/100T-4

C.4.8  Slot Properties—E1000-2

C.4.9  Slot Properties—E1000-2-G

C.4.10  Slot Properties—E100T-12

C.4.11  Slot Properties—E100T-G

C.4.12  Slot Properties—E100-8 (ONS 15305 CTC)

C.4.13  Slot Properties—E100-WAN-8 (ONS 15305 CTC)

C.4.14  Slot Properties—ETH1000

C.4.15  Slot Properties—G1000-2

C.4.16  Slot Properties—G1000-4

C.4.17  Slot Properties—GE-2 (ONS 15305 CTC)

C.4.18  Slot Properties—GigE-WAN-2 (ONS 15305 CTC)

C.4.19  Slot Properties—ML-100T-8

C.4.20  Slot Properties—ML1000-2

C.4.21  Slot Properties—ML100T-12

C.4.22  Slot Properties—ML100X-8

C.4.23  Slot Properties—ML-MR-10

C.4.24  Slot Properties—MS-ISC-100T

C.4.25  Slot Properties—RAN-SVC


Slot Property Information—Common, DWDM, Electrical, and Ethernet Cards


This appendix provides information on the cards supported in CTM. This appendix contains the following sections:

Common Cards

DWDM Cards

Electrical Cards

Ethernet Cards


Note In the CTM GUI, display-only fields have a gray background.


C.1  Common Cards

This section describes the following common cards supported within CTM:

Slot Properties—AIC

Slot Properties—AIC-I

Slot Properties—CTX-2500

Slot Properties—CTX-CL600

Slot Properties—FILLER

Slot Properties—MIC-28-3-A and MIC-28-3-B

Slot Properties—MMU (ONS 15454 SONET and ONS 15454 SDH)

Slot Properties—OSCM (ONS 15454 SONET and ONS 15454 SDH)

Slot Properties—SSXC

Slot Properties—TCC+

Slot Properties—TCC-I

Slot Properties—TCC2

Slot Properties—TCC2P

Slot Properties—TSC (ONS 15600 SONET and ONS 15600 SDH)

Slot Properties—Unprovisioned Slot (ONS 15327 and ONS 15454 SONET)

Slot Properties—Unprovisioned Slot (ONS 15454 SDH)

Slot Properties—XC

Slot Properties—XC-VXL-10G

Slot Properties—XC10G

Slot Properties—XCVT

Slot Properties—XCVXC

Slot Properties—XTC (ONS 15305)

Slot Properties—XTC (ONS 15327)

Slot Properties—TNC

Slot Properties—TSC (ONS 15454 SONET and ONS 15454 SDH)

Slot Properties—TCC3

C.1.1  Slot Properties—AIC

The slot properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The optional Alarm Interface Controller (AIC) card provides customer-defined alarm input/output (I/O) and supports local and express orderwire.

For the AIC module, the slot properties pane displays the following tabs: Module View, Identification, Alarm Extenders, Local Orderwire, Express Orderwire, and Info.

C.1.1.1  Module View Tab

The Module View tab displays a graphic of the AIC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.1.2  Identification Tab

The Identification tab allows you to view and update AIC identification information.

Table C-1 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the Common Language Equipment Identifier (CLEI) code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.1.3  Alarm Extenders Tab

The Alarm Extenders tab allows you view AIC alarm information and create custom alarm types. The Alarm Extenders tab contains the following subtabs:

External Alarms Subtab

External Controls Subtab

User-Defined Alarms Subtab

C.1.1.3.1  External Alarms Subtab

The External Alarms subtab allows you to view and update external alarm information.

Table C-2 Field Descriptions for the External Alarms Subtab 

Field
Description

Input Number

Displays the alarm input number.

Enabled

Check to activate the fields for the alarm input number.

Alarm Type

Choose an alarm type from the provided list.

Severity

Choose a severity from the list.

Raised When

Choose the contact condition that will trigger the alarm in CTC.

Virtual Wire

To assign the external device to a virtual wire, choose a virtual wire from the list, or choose None if no assignment is required.

Description

Displays a default description that is provided for every enabled external alarm.

Raised

Indicates if an alarm has been raised.

Contact Status

Indicates the current status of the contact.


C.1.1.3.2  External Controls Subtab

The External Controls subtab allows you to view and update external controls.

Table C-3 Field Descriptions for the External Controls Subtab 

Field
Description

Control Number

Displays the control number.

Enabled

Check to activate the fields for the control number.

Control Type

Choose a control type from the provided list.

Trigger Type

Choose a trigger type: a local minor, major, or critical alarm; a remote minor, major, or critical alarm; or a virtual wire activation.

Description

Enter a description.

Current State

Displays the current state of the control.

Auto State

Displays the auto state of the control.

Contact Setting

Displays the current contact setting.


C.1.1.3.3  User-Defined Alarms Subtab

The User-Defined Alarms subtab allows you to view, add, and delete custom alarm types on AIC cards.

Table C-4 Field Descriptions for the User-Defined Alarms Subtab 

Field
Description

Alarm Types

Lists the user-defined alarm types that have been created on the AIC card. You can create up to 50 custom environmental alarms, which are reported in the Condition column in the Alarm Log and Alarm Browser windows.

Add

Click the Add button to add a new custom alarm type. Enter a unique alarm type name that contains 20 characters or fewer. Only the following characters are valid: 0-9, A-Z, a-z, and hyphen (-).

Delete

Click the Delete button to delete an existing alarm type.


C.1.1.4  Local Orderwire Tab

Local Orderwire allows a craftsperson to plug a phoneset into a node and communicate with craftspeople working at other nodes or other facility equipment. The orderwire is a pulse code modulation (PCM) encoded voice channel that uses E1 or E2 bytes in section/line overhead. The AIC allows simultaneous use of both local (section overhead signal) and express (line overhead channel) orderwire channels on a SONET ring or particular optics facility. Local orderwire also allows communication at regeneration sites when the regenerator is not a Cisco device.

Table C-5 Field Descriptions for the Local Orderwire Tab 

Field
Description

4-Wire Level

If needed, adjust the Tx and Rx dBm (decibels referenced per milliwatt) by moving the slider to the right or left for the four-wire headset that you will use. In general, you should not need to adjust the dBm.

2-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the two-wire headset that you will use. In general, you should not need to adjust the dBm.


C.1.1.5  Express Orderwire Tab

The Express Orderwire tab allows you to configure express orderwire settings.

Table C-6 Field Descriptions for the Express Orderwire Tab 

Field
Description

4-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the four-wire headset that you will use. In general, you should not need to adjust the dBm.

2-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the two-wire headset that you will use. In general, you should not need to adjust the dBm.


C.1.1.6  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the AIC card.

Table C-7 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.2  Slot Properties—AIC-I

The slot properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The optional Alarm Interface Controller-International (AIC-I) card provides customer-defined (environmental) alarms and controls and supports local and express orderwire. It provides twelve customer-defined input and four customer-defined input/output contacts. The physical connections are through the backplane wire-wrap pin terminals.

For the AIC-I module, the slot properties pane displays the following tabs: Module View, Identification, Card, Alarm Extenders, Local Orderwire, Express Orderwire, and Info.

C.1.2.1  Module View Tab

The Module View tab displays a graphic of the AIC-I that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.2.2  Identification Tab

The Identification tab allows you to view and update AIC-I identification information.

Table C-8 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.2.3  Card Tab

The Card tab allows you to view and update AIC-I card information.

Table C-9 Field Descriptions for the Card Tab 

Field
Description

Add Extension

Check this check box if you are using the Alarm Expansion Panel (AEP).

Extended Type

The AEP radio button is automatically selected if you checked the Add Extension check box.

Input/Output

Select External Alarm if you use external alarms only; select External Control if you use both external alarms and external controls. Selecting only External Alarm gives you 16 external alarm ports and no external control ports. If you select External control, four of the ports are converted to external control ports, leaving you with 12 external alarm ports.

Station Number

Enter a four-digit station number. The valid range is from 0 to 9999.


C.1.2.4  Alarm Extenders Tab

The Alarm Extenders tab allows you view AIC-I alarm information. The Alarm Extenders tab contains the following subtabs:

External Alarms Subtab

External Controls Subtab

User-Defined Alarms Subtab

C.1.2.4.1  External Alarms Subtab

The External Alarms subtab allows you to view and update external alarm information.

Table C-10 Field Descriptions for the External Alarms Subtab 

Field
Description

Input Number

The alarm input number.

Enabled

Check to activate the fields for the alarm input number.

Alarm Type

Choose an alarm type from the provided list.

Severity

Choose a severity from the list.

Raised When

Choose the contact condition that will trigger the alarm in CTC.

Virtual Wire

To assign the external device to a virtual wire, choose a virtual wire from the list, or choose None if no assignment is required.

Description

A default description is provided in this line for every external alarm that is enabled.

Raised

Indicates if an alarm has been raised.

Contact Status

Indicates the current status of the contact.


C.1.2.4.2  External Controls Subtab

The External Controls subtab allows you to view and update external controls.

Table C-11 Field Descriptions for the External Controls Subtab 

Field
Description

Control Number

The control number.

Enabled

Check to activate the fields for the control number.

Control Type

Choose a control type from the provided list.

Trigger Type

Choose a trigger type: a local minor, major, or critical alarm; a remote minor, major, or critical alarm; or a virtual wire activation.

Description

Enter a description.

Current State

The current state of the control.

Auto State

The auto state of the control.

Contact Setting

The current contact setting.


C.1.2.4.3  User-Defined Alarms Subtab

The User-Defined Alarms subtab allows you to view, add, and delete custom alarm types on AIC-I cards.

Table C-12 Field Descriptions for the User-Defined Alarms Subtab 

Field
Description

Alarm Types

Lists the user-defined alarm types that have been created on the AIC-I card. You can create up to 50 custom environmental alarms, which are reported in the Condition column in the Alarm Log and Alarm Browser windows.

Add

Click the Add button to add a new custom alarm type. Enter a unique alarm type name that contains 20 characters or fewer. Only the following characters are valid: 0-9, A-Z, a-z, and hyphen (-).

Delete

Click the Delete button to delete an existing alarm type.


C.1.2.5  Local Orderwire Tab

Orderwire allows a craftsperson to plug a phoneset into a node and communicate with craftspeople working at other nodes or other facility equipment. The orderwire is a pulse code modulation (PCM) encoded voice channel that uses E1 or E2 bytes in section/line overhead. The AIC-I allows simultaneous use of both local (section overhead signal) and express (line overhead channel) orderwire channels on a SONET ring or particular optics facility. Local orderwire also allows communication at regeneration sites when the regenerator is not a Cisco device.

Table C-13 Field Descriptions for the Local Orderwire Tab 

Field
Description

Buzzer

The AIC-I supports selective dual tone multifrequency (DTMF) dialing for telephony connectivity, which causes one AIC-I card or all AIC-I cards on the orderwire subnetwork to ring. The ringer/buzzer resides on the AIC-I. If you want to turn on the audible alert (buzzer) for the orderwire, check the Buzzer check box.

4-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the four-wire headset that you will use. In general, you should not need to adjust the dBm.

2-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the two-wire headset that you will use. In general, you should not need to adjust the dBm.


C.1.2.6  Express Orderwire Tab

The Express Orderwire tab allows you to configure express orderwire settings.

Table C-14 Field Descriptions for the Express Orderwire Tab 

Field
Description

Buzzer

If you want to turn on the audible alert (buzzer) for the orderwire, check the Buzzer check box.

4-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the four-wire headset that you will use. In general, you should not need to adjust the dBm.

2-Wire Level

If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the two-wire headset that you will use. In general, you should not need to adjust the dBm.


C.1.2.7  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the AIC-I card.

Table C-15 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.3  Slot Properties—CTX-2500

The slot properties pane displays information about the Cisco ONS 15310 MA SONET or ONS 15310 MA SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The CTX-2500 card, for use with the ONS 15310 MA SONET or ONS 15310 MA SDH, is a fully nonblocking cross-connect card that operates in a redundant configuration. It performs system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SONET data communications channel (DCC) termination, system fault detection, and cross-connect maintenance and management for the ONS 15310 MA SONET and ONS 15310 MA SDH. The card also provides the circuitry for the OC-3/OC-12/OC-48 interfaces, and ensures that the system maintains timing with SMC stability.

The CTX-2500 card provides 576 x 576 STS-1 level cross-connections, 96 x 96 TU-3 level cross-connections, 2688 x 2688 VT1.5s, or 2016 x 2016 VT2s.

The CTX-2500 card can be installed in slots 3 or 4. Protection switches between the active and standby CTX-2500 are hitless (less than a 50-ms impact to any traffic).

The CTX-2500 supports errorless side switches (switching from one CTX-2500 on one side of the shelf to the other CTX-2500 on the other side of the shelf) when the switch is initiated through software and is caused by a software upgrade.

There are two PPM (small form factor pluggable [SFP]) slots on the CTX-2500 faceplate. Each slot can contain a one-port PPM. Cisco-qualified SFPs can be single-rate (OC-3, OC-12, or OC-48) or multirate (OC-3, OC-12, and OC-48). Single-rate PPMs are autoprovisioned when they are installed, but multirate PPMs must be provisioned. This behavior can be controlled by NE defaults.

The following figure shows the CTX-2500 card faceplate.

Figure C-1 CTX-2500 Faceplate

For the CTX-2500 module, the slot properties pane displays the following tabs: Module View, Identification, Pluggable Provisioning, Line, STS, VT, Loopback, Alarm Behavior, Transceiver, Auto Laser Shutdown, Protection, J1 Path Trace, and Section Trace.

C.1.3.1  Module View Tab

The Module View tab displays a graphic of the CTX-2500 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.3.2  Identification Tab

The Identification tab allows you to view and update CTX-2500 identification information.

Table C-16 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Card State

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.3.3  Pluggable Provisioning Tab

The Pluggable Provisioning tab allows you to view and provision pluggable entities; for example, the pluggable port module (PPM) and pluggable I/O module (PIM) and the ports inside these entities.

Table C-17 Field Descriptions for the Pluggable Provisioning Tab 

Field
Description

Pluggable Number

Displays the identifier of the plugin module.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Equipment State

Displays the equipment state of the card.

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Pluggable Number

Displays the identifier of the plugin module and the port number.

Rate

Displays the rate of the port inside the pluggable entity.


C.1.3.3.1  Provision Pluggable Dialog Box

Click the Create button to launch the Provision Pluggable dialog box. This dialog box allows you to provision pluggable entities such as the PPM and PIM, and to create the ports inside these entities.

Table C-18 describes the fields displayed in the Provision Pluggable dialog box when provisioning a PPM.

Table C-19 applies only to the ONS 15600 SONET/SDH ASAP_4 card and describes the fields displayed in the Provision Pluggable dialog box when provisioning a PIM.

Table C-20 describes the fields displayed in the Provision Pluggable dialog box when provisioning a PPM.

Table C-21 describes the fields displayed in the Provision Pluggable dialog box when creating the ports inside the PPM and PIM.

Table C-18 Field Descriptions for the Provision Pluggable Dialog Box—PPM 

Field
Description

PPM #

Sets the PPM number.

No. of Ports

Sets the number of ports inside the PPM.

PPM Type

Sets the type of PPM.


Table C-19 Field Descriptions for the Provision Pluggable Dialog Box—PIM (ONS 15600 SONET/SDH ASAP_4 Card) 

Field
Description

PIM #

Sets the PIM number.

No. of Ports

Sets the number of ports inside the PIM.

PIM Type

Sets the type of PIM.


Table C-20 Field Descriptions for the Provision Pluggable Dialog Box—PPM (ONS 15454 SONET/SDH MRC-12 Card) 

Field
Description

PPM

Select the PPM for which you want to create the port.

PPM Type

Sets the PPM type.


Table C-21 Field Descriptions for the Provision Pluggable Dialog Box 

Field
Description

PPM

Select the PPM for which you want to create the port.

Port Number

Sets the port number.

Port Rate

Sets the rate of the new port.


C.1.3.4  Line Tab

The Line tab allows you to view and update line card information. The Line tab displays the following subtabs:

Line Config Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

Physical Thresh 15 Min Subtab

Physical Thresh 1 Day Subtab

Alarm Thresholds Subtab

C.1.3.4.1  Line Config Subtab

The Line Config subtab allows you to view and change the line settings of an optical card.

Table C-22 Field Descriptions for the Line Config Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a name for the optical port.

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Port Rate

Sets the rate of the new port.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

ProvidesSync

When checked, the card is provisioned as an NE timing reference.

EnableSyncMsg

Enables synchronization status messages (S1 byte), which allow the node to choose the best timing source.

SendDoNotUse

When checked, sends a do not use (DUS) message on the S1 byte.

Send <FF> DoNotUse

When checked, sends a do not use (DUS) (0xff) message on the S1 byte.

Type

Defines the port as SONET or SDH.

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

AINS Soak Count Down

Automatic in-service soak countdown. Displays the remaining time of valid input signal in hh:mm format, after which the card becomes in service (IS) automatically.

Admin SSM

If the node does not receive an SSM signal, it defaults to synchronization traceability unknown (STU). Admin SSM allows you to override the STU value with one of the following:

PRS—Primary reference source (Stratum 1)

STS2—Stratum 2

TNC—Transit node clock

STS3E—Stratum 3E

STS3—Stratum 3

SMC—SONET minimum clock

ST4—Stratum 4

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

PJSTSMon#

Sets the STS that will be used for pointer justification. If set to 0, no STS is monitored. Only one STS can be monitored on each OC-N port.

0 (default)-3 (OC-3, per port)

0 (default)-12 (OC-12)

0 (default)-48 (OC-48)

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency. The Wavelength column lists the correct wavelengths, depending on the type of card and the band selected.


C.1.3.4.2  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the near- and far-end 15-minute threshold settings of an optical card.

Table C-23 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.

PSC

In a 1 + 1 protection scheme for a working card, protection switching count (PSC) is a count of the number of times service switches from a working card to a protection card plus the number of times service switches back to the working card. For a protection card, PSC is a count of the number of times service switches to a working card from a protection card plus the number of times service switches back to the protection card. The PSC PM is applicable only if revertive line-level protection switching is used. PSC is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

PSD

Protection switching duration (PSD) applies to the length of time, in seconds, that service is carried on another line. For a working line, PSD is a count of the number of seconds that service was carried on the protection line. For the protection line, it is a count of the seconds that the line was used to carry service. The PSD PM is applicable only if revertive line-level protection switching is used. PSD is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.


C.1.3.4.3  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the near- and far-end 1-day threshold settings of an optical card.

Table C-24 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.

PSC

In a 1 + 1 protection scheme for a working card, protection switching count (PSC) is a count of the number of times service switches from a working card to a protection card plus the number of times service switches back to the working card. For a protection card, PSC is a count of the number of times service switches to a working card from a protection card plus the number of times service switches back to the protection card. The PSC PM is applicable only if revertive line-level protection switching is used. PSC is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

PSD

Protection switching duration (PSD) applies to the length of time, in seconds, that service is carried on another line. For a working line, PSD is a count of the number of seconds that service was carried on the protection line. For the protection line, it is a count of the seconds that the line was used to carry service. The PSD PM is applicable only if revertive line-level protection switching is used. PSD is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.


C.1.3.4.4  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change the near-end 15-minute section threshold settings of an optical card.

Table C-25 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.


C.1.3.4.5  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change the near-end 1-day section threshold settings of an optical card.

Table C-26 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.


C.1.3.4.6  Physical Thresh 15 Min Subtab

The Physical Thresh 15 Min subtab allows you to view and change 15-minute physical threshold information on an optical card.

Table C-27 Field Descriptions for the Physical Thresh 15 Min Subtab 

Field
Description

Port No.

Pluggable entity number and port number.

LBC-HIGH

Maximum laser bias current. The default is (15 min): 200 percent.

LBC-LOW

Minimum laser bias current. The default is (15 min): 20 percent.

OPT-HIGH

Maximum optical power transmitted. The default is (15 min): 120 percent.

OPT-LOW

Minimum optical power transmitted. The default is (15 min): 80 percent.

OPR-HIGH

Maximum optical power received. The default is (15 min): 200 percent.

OPR-LOW

Minimum optical power received. The default is (15 min): 50 percent.

Set OPR

Setting the optical power received (OPR) establishes the received power level as 100 percent. If the received power decreases, then the OPR percentage decreases to reflect the loss in received power. For example, if the received power decreases 3-dBm, the OPR decreases 50 percent.


C.1.3.4.7  Physical Thresh 1 Day Subtab

The Physical Thresh 1 Day subtab allows you to view and change 1-day physical threshold information on an optical card.

Table C-28 Field Descriptions for the Physical Thresh 1 Day Subtab 

Field
Description

Port No.

Pluggable entity number and port number.

LBC-HIGH

Maximum laser bias current. The default is (15 min): 200 percent.

LBC-LOW

Minimum laser bias current. The default is (15 min): 20 percent.

OPT-HIGH

Maximum optical power transmitted. The default is (15 min): 120 percent.

OPT-LOW

Minimum optical power transmitted. The default is (15 min): 80 percent.

OPR-HIGH

Maximum optical power received. The default is (15 min): 200 percent.

OPR-LOW

Minimum optical power received. The default is (15 min): 50 percent.

Set OPR

Setting the OPR establishes the received power level as 100 percent. If the received power decreases, then the OPR percentage decreases to reflect the loss in received power. For example, if the received power decreases 3-dBm, the OPR decreases 50 percent.


C.1.3.4.8  Alarm Thresholds Subtab

The Alarm Thresholds subtab allows you to select thresholds for alarm generation.

Table C-29 Field Descriptions for the Alarm Thresholds Subtab 

Field
Description

Port Number

The port number.

LBC-High

Maximum laser bias current. The default is (15 min): 200 percent.

LBC-Low

Minimum laser bias current. The default is (15 min): 20 percent.

OPT-High

Maximum optical power transmitted. The default is (15 min): 120 percent.

OPT-Low

Minimum optical power transmitted. The default is (15 min): 80 percent.

OPR-High

Maximum optical power received. The default is (15 min): 200 percent.

OPR-Low

Minimum optical power received. The default is (15 min): 50 percent.

Set OPR

Setting the OPR establishes the received power level as 100 percent. If the received power decreases, then the OPR percentage decreases to reflect the loss in received power. For example, if the received power decreases 3-dBm, the OPR decreases 50 percent.


C.1.3.5  STS Tab

The STS tab allows you to view and update synchronous transport signal (STS) information. The STS tab displays the following subtabs:

STS Config Subtab

Path Thresh 15 Min Subtab

Path Thresh 1 Day Subtab

Customer Info Subtab

C.1.3.5.1  STS Config Subtab

The STS Config subtab allows you to view and change the STS settings of the EC1 port.

Table C-30 Field Descriptions for the STS Config Subtab 

Field
Description

STS Number

Displays the synchronous transport signal number information.

IPPM Enabled

Check to enable intermediate path performance monitoring (IPPM) and uncheck to disable IPPM.

XC Loopback

Displays the cross-connect loopback status.


C.1.3.5.2  Path Thresh 15 Min Subtab

The Path Thresh 15 Min subtab allows you to view and change the 15-minute path threshold information for the CTX-2500 card.

Table C-31 Field Descriptions for the Path Thresh 15 Min Subtab 

Field
Description
Near End

STS No.

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Displays the severely errored frame/alarm indication signal path information.

UAS-P

Displays the unavailable seconds path information.

PPJC-Pdet

Displays positive pointer justification count-VC4 path detected.

NPJC-Pdet

Displays negative pointer justification count-VC4 path detected.

PPJC-Pgen

Displays positive pointer justification count-VC4 path generated.

NPJC-Pgen

Displays negative pointer justification count-VC4 path generated.

PJCS-Pdet

Indicates the number of pointer justification count seconds (PJCS) detected on a particular path.

PJCS-Pgen

Indicates the number of pointer justification count seconds generated for a particular path.

PJC-Diff

Displays the sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.

Far End

STS No.

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.


C.1.3.5.3  Path Thresh 1 Day Subtab

The Path Thresh 1 Day subtab allows you to view and change the 1-day path threshold information for the CTX-2500 card.

Table C-32 Field Descriptions for the Path Thresh 1 Day Subtab 

Field
Description
Near End

STS No.

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

PPJC-Pdet

Displays positive pointer justification count-VC4 path detected.

NPJC-Pdet

Displays negative pointer justification count-VC4 path detected.

PPJC-Pgen

Displays positive pointer justification count-VC4 path generated.

NPJC-Pgen

Displays negative pointer justification count-VC4 path generated.

PJCS-Pdet

Indicates the number of pointer justification count seconds (PJCS) detected on a particular path.

PJCS-Pgen

Indicates the number of pointer justification count seconds generated for a particular path.

PJC-Diff

Displays the sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.

Far End

STS No.

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.


C.1.3.5.4  Customer Info Subtab

The Customer Info subtab displays customer information.

Table C-33 Field Descriptions for the Customer Subtab 

Field
Description

STS No.

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.3.6  VT Tab

The VT tab allows you to view and update VT line information. The VT tab displays the following subtabs:

VT Config Subtab

VT Thresh 15 Min Subtab

VT Thresh 1 Day Subtab

Customer Info Subtab

C.1.3.6.1  VT Config Subtab

The VT Config subtab allows you to view and change the VT settings of the card.

Table C-34 Field Descriptions for the VT Config Subtab 

Field
Description

VT No.

Displays VT number information.

IPPM Enabled

Check to enable intermediate path performance monitoring (IPPM) and uncheck to disable IPPM.


C.1.3.6.2  VT Thresh 15 Min Subtab

The VT Thresh 15 Min subtab displays near- and far-end 15-minute VT threshold information.

Table C-35 Field Descriptions for the VT Thresh 15 Min Subtab 

Field
Description

VT No.

Displays VT number information.

CV

Displays the coding violations information.

ES

Displays the errored seconds information.

SES

Displays the severely errored seconds information.

UAS

Displays the unavailable seconds information.

FC

Displays the failure count information.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.3.6.3  VT Thresh 1 Day Subtab

The VT Thresh 1 Day subtab displays near- and far-end 1-day VT threshold information.

Table C-36 Field Descriptions for the VT Thresh 1 Day Subtab 

Field
Description

VT No.

Displays VT number information.

CV

Displays the coding violations information.

ES

Displays the errored seconds information.

SES

Displays the severely errored seconds information.

UAS

Displays the unavailable seconds information.

FC

Displays the failure count information.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.3.6.4  Customer Info Subtab

The Customer Info subtab displays customer information.

Table C-37 Field Descriptions for the Customer Subtab 

Field
Description

STS No.

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.3.7  Loopback Tab

The Loopback tab allows you to view and update CTX-2500 loopback information.

Table C-38 Field Descriptions for the Loopback Tab 

Field
Description

Port Number

Displays the port number.

Administration State

Allows you to select the administration state of the port: In Service (IS) or Out of Service (OOS).

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or clear the current loopback (none).

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Send AIS on Facility Loopback

When selected, sends AIS on the facility loopback.

Send AIS on Terminal Loopback

When selected, sends AIS on the terminal loopback.


C.1.3.8  Alarm Behavior Tab

The Alarm Behavior tab allows you to view and update alarm profiles assigned to cards on the ONS 15310 MA SONET or ONS 15310 MA SDH node.

Table C-39 Field Descriptions for the Alarm Behavior Tab 

Field
Description

Alarm Profile

Displays the alarm profile that has been configured for the card.

Suppress Alarms

When checked, indicates that all alarms are suppressed for the card.

Port Number

Displays the card port number.

Alarm Profile

Choose an alarm profile for the port from the drop-down list. Values are Default, Inherited, or a customized alarm profile.

Suppress Alarms

When checked, all alarms are suppressed for the port.

Alarm Profile

Choose an alarm profile for all ports.

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.1.3.9  Transceiver Tab

The Transceiver tab shows OC-N port optical power received (OPR), optical power transmitted (OPT), and laser bias current (LBC) from the line card and stores these values with the PM counts for the 15-minute and 1-day periods. The physical layer performance parameters consist of normalized and non-normalized values of LBC, OPT, and OPR.

Table C-40 Field Descriptions for the Transceiver Tab 

Field
Description

Port No.

Displays the port number.

Non-Normalized LBC (mA)

Displays the actual operating value of laser bias current (mA) for the specified card port. This value should be somewhat consistent from port to port and cannot be configured.

Non-Normalized OPT (dBm)

Displays the actual operating value of optical power transmitted (dBm) for the specified card port. This value should be somewhat consistent from port to port and cannot be configured.

Non-Normalized OPR (dBm)

Displays the actual operating value of optical power received (dBm) for the specified card port. This value varies from port to port because of received optical signal power differences.


C.1.3.10  Auto Laser Shutdown Tab

The Auto Laser Shutdown tab allows you to view and update the automatic laser shutdown parameters.

Table C-41 Field Descriptions for the Auto Laser Shutdown Tab 

Field
Description

Port Number

Displays the port number.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.


C.1.3.11  Protection Tab

The Protection tab allows you to view and update protection group information.

Table C-42 Field Descriptions for the Protection Tab 

Field
Description

Protection Groups

Displays a list of available protection groups.

Protection Group Details

Displays details about the selected protection group.


C.1.3.12  J1 Path Trace Tab

The J1 Path Trace tab allows you to view and retrieve J1 path trace information.

Table C-43 Field Descriptions for the J1 Path Trace Tab 

Field
Description

Port Number

Displays the port number.

STS/VC Number

Displays the STS or VC number.

Expected String

Displays the current expected string.

Received String

Displays the current received string.

Mode

Displays the path trace mode (Off/None, Auto, or Manual).

C2

Represents a machine-generated J1/J2 payload label byte.

Display

Click the Display button to view the circuit trace information. See 7.2.21.5  Using the Circuit Trace Window to Apply Protection to the Ports in a Splitter-Protection Group, page 7-165 for more information.

Retrieve

Click the Retrieve button to retrieve J1 path trace information.


C.1.3.13  Section Trace Tab

The Section Trace tab is used to provision section trace.

Table C-44 Field Descriptions for the Section Trace Tab 

Field
Description

Port No.

Displays the port number.

Trace Mode

Displays the trace mode (Off/None or Manual).

Disable AIS/RDI on TIM-S

Allows you to disable the Alarm Indication Signal (AIS) and the Remote Defect Indication (RDI) when the path Trace Identifier Mismatch Section (TIM-S) alarm is detected.

Transmit Length

Select a transmit length for the trace.

Current Transmit String

Displays the current transmit string. The trail trace identifier is 64 bytes in length.

Current Expected String

Displays the current expected string; sets a new expected string.

Current Received String

Displays the current received string.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.4  Slot Properties—CTX-CL600

The slot properties pane displays information about the Cisco ONS 15310 CL slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The CTX-CL600 card is an unpluggable card on the ONS 15310 CL NE. It has a total of 26 ports that are either mounted or pluggable.

For the CTX-CL600 module, the slot properties pane displays the following tabs: Module View, Identification, Wideband Ports, Broadband Ports, Pluggable Provisioning, DS-1, DS-3, EC1, Optical, Alarm Extenders, and Info.

C.1.4.1  Module View Tab

The Module View tab displays a graphic of the CTX-CL600 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.4.2  Identification Tab

The Identification tab allows you to view and update CTX-CL600 identification information.

Table C-45 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.4.3  Wideband Ports Tab

The Wideband Ports tab allows you to view the wideband port information.

Table C-46 Field Descriptions for the Wideband Ports Tab 

Field
Description

Port Number

Displays the port number.

Rate

Displays the rate that the slot is provisioned for.


C.1.4.4  Broadband Ports Tab

The Broadband Ports tab allows you to view, create, and delete DS-3 and EC1 broadband ports.

Table C-47 Field Descriptions for the Broadband Ports Tab 

Field
Description

Create

Click the Create button to launch the Create Port dialog box and create a new broadband port. Use the Port Number drop-down list to choose an available port. Use the Port Rate drop-down list to specify the port rate (DS-3 or EC1). After making your selections, click OK.

Delete

Click the Delete button to delete an existing DS-3 or EC1 broadband port.

DS-3

Port Number

Displays the DS-3 port number.

Rate

Displays the rate that the slot is provisioned for.

EC1

Port Number

Displays the EC1 port number.

Rate

Displays the rate that the slot is provisioned for.


C.1.4.5  Pluggable Provisioning Tab

The Pluggable Provisioning tab allows you to view and provision pluggable entities; for example, the pluggable port module (PPM) and pluggable I/O module (PIM) and the ports inside these entities.

Table C-48 Field Descriptions for the Pluggable Provisioning Tab 

Field
Description

Pluggable Number

Displays the identifier of the plugin module.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Pluggable Number

Displays the identifier of the plugin module and the port number.

Rate

Displays the rate of the port inside the pluggable entity.


C.1.4.5.1  Provision Pluggable Dialog Box

Click the Create button to launch the Provision Pluggable dialog box. This dialog box allows you to provision pluggable entities such as the PPM and PIM, and to create the ports inside these entities.

Table C-49 applies only to the ONS 15600 SONET/SDH ASAP_4 card and describes the fields displayed in the Provision Pluggable dialog box when provisioning a PIM.

Table C-50 applies only to the ONS 15600 SONET/SDH ASAP_4 card and describes the fields displayed in the Provision Pluggable dialog box when creating the ports inside the PPM and PIM.

Table C-51 describes the fields displayed in the Provision Pluggable dialog box when provisioning a PPM.

Table C-52 describes the fields displayed in the Provision Pluggable dialog box when creating the ports inside the PPM.

Table C-49 Field Descriptions for the Provision Pluggable Dialog Box—PIM (ONS 15600 SONET/SDH ASAP_4 Card) 

Field
Description

PIM #

Sets the PIM number.

PIM Type

Sets the type of PIM.


Table C-50 Field Descriptions for the Provision Pluggable Dialog Box—PPM (ONS 15600 SONET/SDH ASAP_4 Card)

Field
Description

PIM

Select the PIM for which you want to create the port.

PPM

Select the PPM for which you want to create the port.

Port Rate

Sets the rate of the new port.


Table C-51 Field Descriptions for the Provision Pluggable Dialog Box—PPM (ONS 15454 SONET/SDH MRC-12 Card) 

Field
Description

PPM

Select the PPM for which you want to create the port.

PPM Type

Sets the PPM type.


Table C-52 Field Descriptions for the Provision Pluggable Dialog Box 

Field
Description

PPM

Select the PPM for which you want to create the port.

Port Rate

Sets the rate of the new port.


C.1.4.6  DS-1 Tab

The DS-1 tab allows you to view node near-end and far-end performance on a DS-1 card to detect possible performance problems. The DS-1 tab contains the following subtabs:

Line Config Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Electric Path Thresh 15 Min Subtab

Electric Path Thresh 1 Day Subtab

STS Thresh 15 Min Subtab

STS Thresh 1 Day Subtab

VT Thresh 15 Min Subtab

VT Thresh 1 Day Subtab

Alarm Behavior Subtab

Loopback Subtab

J1 Path Trace Subtab

Customer Info Subtab

C.1.4.6.1  Line Config Subtab

The Line Config subtab allows you to view and change the line settings of the DS-1 card.

Table C-53 Field Descriptions for the Line Config Subtab 

Field
Description

Port Name

Allows you to add a name for the optical port.

Line Type

Allows you to select the line framing type.

Line Coding

Allows you to define the DS-1 transmission coding type.

Line Length

Defines the distance (in feet) from backplane connection to the next termination point.

0-131 (default)

132-262

263-393

394-524

525-655

Administration State

Displays the status of the line: In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

AINS Soak Count Down

Automatic in-service soak countdown. Displays the remaining time of valid input signal in hh:mm format, after which the card becomes in service (IS) automatically.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

Send Do Not Use

When checked, sends a do not use (DUS) message on the S1 byte.

Provide Sync

When checked, the card is provisioned as an NE timing reference.

Enable Sync Message

When checked, enables synchronization status messages, which allow the node to choose the best timing source.

Enable Retiming

When checked, enables retiming. Retiming removes accumulated jitter and wander from synchronous transport network payload signals. Retiming should not be enabled when accumulated jitter and wander is not present.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Send AIS-V for DS-1 AIS

When checked, sends an Alarm Indication Signal VT (AIS-V) instead of a DS-1 AIS (from the line side toward the backplane/system side) when a line-side trigger occurs.

Raise AIS for LOF

Sends an AIS when a loss of frame (LOF) occurs.


C.1.4.6.2  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the near- and far-end 15-minute threshold settings of the DS-1 card.

Table C-54 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

CV-L

Displays the coding violations line.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

LOSS-L

Displays the loss of signal seconds line.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.


C.1.4.6.3  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the near- and far-end 1-day threshold settings of the DS-1 card.

Table C-55 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

CV-L

Displays the coding violations line.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

LOSS-L

Displays the loss of signal seconds line.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.


C.1.4.6.4  Electric Path Thresh 15 Min Subtab

The Electric Path Thresh 15 Min subtab allows you to view and change the near- and far-end 15-minute electrical path threshold settings for the DS-1 card.

Table C-56 Field Descriptions for the Electric Path Thresh 15 Min Subtab 

Field
Description
Near End

Port No.

Displays the port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Displays the severely errored frame/alarm indication signal path information.

AISS-P

Displays the alarm indication signal seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

Far End

Port No.

Displays the port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

ESA-P

Displays the errored seconds type A path information.

ESB-P

Displays the errored seconds type B path information.

CSS-P

Displays the controlled slip seconds path information.

SEFS-P

Displays the severely errored framing seconds path information.


C.1.4.6.5  Electric Path Thresh 1 Day Subtab

The Electric Path Thresh 1 Day subtab allows you to view and change the near- and far-end 1-day electrical path threshold settings for the DS-1 card.

Table C-57 Field Descriptions for the Electric Path Thresh 1 Day Subtab 

Field
Description
Near End

Port No.

Displays the port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Displays the severely errored frame/alarm indication signal-path information.

AISS-P

Displays the alarm indication signal seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

Far End

Port No.

Displays the port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

ESA-P

Displays the errored seconds type A path information.

ESB-P

Displays the errored seconds type B path information.

CSS-P

Displays the controlled slip seconds path information.

SEFS-P

Displays the severely errored framing seconds path information.


C.1.4.6.6  STS Thresh 15 Min Subtab

The STS Thresh 15 Min subtab allows you to view and change near- and far-end 15-minute STS information for the DS-1 card.

Table C-58 Field Descriptions for the STS Thresh 15 Min Subtab 

Field
Description
Near End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

Far End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.


C.1.4.6.7  STS Thresh 1 Day Subtab

The STS Thresh 1 Day subtab allows you to view and change near- and far-end 1-day STS information for the DS-1 card.

Table C-59 Field Descriptions for the STS Thresh 1 Day Subtab 

Field
Description
Near End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

Far End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.


C.1.4.6.8  VT Thresh 15 Min Subtab

The VT Thresh 15 Min subtab displays near- and far-end 15-minute VT threshold information.

Table C-60 Field Descriptions for the VT Thresh 15 Min Subtab 

Field
Description
Near End

VT Number

Displays VT number information.

CV-V

Displays the coding violations-VT path information.

ES-V

Displays the errored seconds-VT path information.

SES-V

Displays the severely errored seconds-VT path information.

UAS-V

Displays the unavailable seconds-VT path information.

Far End

VT Number

Displays VT number information.

CV-V

Displays the coding violations-VT path information.

ES-V

Displays the errored seconds-VT path information.

SES-V

Displays the severely errored seconds-VT path information.

UAS-V

Displays the unavailable seconds-VT path information.


C.1.4.6.9  VT Thresh 1 Day Subtab

The VT Thresh 1 Day subtab displays near- and far-end 1-day VT threshold information.

Table C-61 Field Descriptions for the VT Thresh 1 Day Subtab 

Field
Description
Near End

VT Number

Displays VT number information.

CV-V

Displays the coding violations-VT path information.

ES-V

Displays the errored seconds-VT path information.

SES-V

Displays the severely errored seconds-VT path information.

UAS-V

Displays the unavailable seconds-VT path information.

Far End

VT Number

Displays VT number information.

CV-V

Displays the coding violations-VT path information.

ES-V

Displays the errored seconds-VT path information.

SES-V

Displays the severely errored seconds-VT path information.

UAS-V

Displays the unavailable seconds-VT path information.


C.1.4.6.10  Alarm Behavior Subtab

The Alarm Behavior subtab allows you to view and update DS-1 alarm profile information.

Table C-62 Field Descriptions for the Alarm Behavior Subtab 

Field
Description

Alarm Profile

Select the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Port Number

Displays the port number.

Alarm Profile

Displays the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.1.4.6.11  Loopback Subtab

The Loopback subtab allows you to view and update DS-1 loopback information.

Table C-63 Field Descriptions for the Loopback Subtab 

Field
Description

Line Number

Displays the line number.

Administration State

Allows you to configure the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT)

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or Facility (Line), or clear the current loopback (none).

Note The line state must be OOS_MT before you can configure the loopback type.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Send Code

Allows you to send loopback commands to the far end.

Send AIS on Facility Loopback

When selected, sends AIS on the facility loopback.

Send AIS on Terminal Loopback

When selected, sends AIS on the terminal loopback.


C.1.4.6.12  J1 Path Trace Subtab

The J1 Path Trace subtab allows you to view and retrieve J1 path trace information.

Table C-64  Field Descriptions for the J1 Path Trace Subtab 

Field
Description

Port Number

Displays the port number.

STS Number

Displays the synchronous transport signal number.

Expected String

Displays the current expected string.

Received String

Displays the current received string.

Mode

Displays the path trace mode (Off/None, Auto, or Manual).

C2

Represents a machine-generated J1/J2 payload label byte.

Display

Click the Display button to view the circuit trace information. See 7.2.21.6  Viewing a J1 Path Trace from the NE Explorer, page 7-167 for more information.

Retrieve

Click the Retrieve button to retrieve J1 path trace information.


C.1.4.6.13  Customer Info Subtab

The Customer Info subtab displays customer information.

Table C-65 Field Descriptions for the Customer Info Subtab 

Field
Description

STS Number, VT Number

Displays the STS or VT number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.4.7  DS-3 Tab

The DS-3 tab allows you to view node near-end and far-end performance on a DS-3 card to detect possible performance problems. The DS-3 tab contains the following subtabs:

Line Config Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

PBit Thresh 15 Min Subtab

PBit Thresh 1 Day Subtab

CPBit Thresh 15 Min Subtab

CPBit Thresh 1 Day Subtab

STS Thresh 15 Min Subtab

STS Thresh 1 Day Subtab

Alarm Behavior Subtab

Loopback Subtab

J1 Path Trace Subtab

Customer Info Subtab

C.1.4.7.1  Line Config Subtab

The Line Config subtab allows you to view and change the line settings of the DS-3 card.

Table C-66 Field Descriptions for the Line Config Subtab 

Field
Description

Port Number

Displays the port number for the optical port.

Port Name

Allows you to add a name for the optical port.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

Line Length

Defines the distance (in feet) from backplane connection to the next termination point.

0 - 225 (default)

226 - 450

Line Type

Allows you to select the line framing type.

Line Coding

Allows you to define the transmission coding type.

Administration State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

AINS Soak Count Down

Automatic in-service soak countdown. Displays the remaining time of valid input signal in hh:mm format, after which the card becomes in service (IS) automatically.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.


C.1.4.7.2  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the near- and far-end 15-minute threshold settings of the DS-3 card.

Table C-67 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description

Port Number

Displays the optical port number.

CV-L

Displays the coding violations line (near-end only).

ES-L

Displays the errored seconds lines line.

SES-L

Displays the severely errored seconds line (near-end only).

LOSS-L

Displays the loss of signal seconds line (near-end only).


C.1.4.7.3  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the near- and far-end 1-day threshold settings of the DS-3 card.

Table C-68 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description

Port Number

Displays the optical port number.

CV-L

Displays the coding violations line (near-end only).

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line (near-end only).

LOSS-L

Displays the loss of signal seconds line (near-end only).


C.1.4.7.4  PBit Thresh 15 Min Subtab

The PBit Thresh 15 Min subtab displays near-end 15-minute PBit path threshold information on the DS-3 card.

Table C-69 Field Descriptions for the PBit Thresh 15 Min Subtab 

Field
Description
Near End

Port No.

Displays the optical port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Severely errored frame/alarm indication signal-path

AISS-P

Alarm indication signal seconds path

UAS-P

Displays the unavailable seconds path information.


C.1.4.7.5  PBit Thresh 1 Day Subtab

The PBit Thresh 1 Day subtab displays near- and far-end 1-day PBit path threshold information on the DS-3 card.

Table C-70 Field Descriptions for the PBit Thresh 1 Day Subtab 

Field
Description
Near End

Port No.

Displays the optical port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Severely errored frame/alarm indication signal-path information.

AISS-P

Alarm indication signal seconds path information.

UAS-P

Displays the unavailable seconds path information.


C.1.4.7.6  CPBit Thresh 15 Min Subtab

The CPBit Thresh 15 Min subtab displays near- and far-end 15-minute CPBit path threshold information on the DS-3 card.

Table C-71 Field Descriptions for the CPBit Thresh 15 Min Subtab 

Field
Description
Near End

Port No.

Displays the optical port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

Far End

Port No.

Displays the optical port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Displays the severely errored frame/alarm indication signal-path information.

UAS-P

Displays the unavailable seconds path information.


C.1.4.7.7  CPBit Thresh 1 Day Subtab

The CPBit Thresh 1 Day subtab displays near- and far-end 1-day CPBit path threshold information on the DS-3 card.

Table C-72 Field Descriptions for the CPBit Thresh 1 Day Subtab 

Field
Description
Near End

Port No.

Displays the optical port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

Far End

Port No.

Displays the optical port number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

SAS-P

Displays the severely errored frame/alarm indication signal path information.

UAS-P

Displays the unavailable seconds path information.


C.1.4.7.8  STS Thresh 15 Min Subtab

The STS Thresh 15 Min subtab allows you to view and change near- and far-end 15-minute STS information on the card.

Table C-73 Field Descriptions for the STS Thresh 15 Min Subtab 

Field
Description
Near End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

Far End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.


C.1.4.7.9  STS Thresh 1 Day Subtab

The STS Thresh 1 Day subtab allows you to view and change near- and far-end 1-day STS information on the DS-3 card.

Table C-74 Field Descriptions for the STS Thresh 1 Day Subtab 

Field
Description
Near End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

Far End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.


C.1.4.7.10  Alarm Behavior Subtab

The Alarm Behavior subtab allows you to view and update DS-3 alarm profile information.

Table C-75 Field Descriptions for the Alarm Behavior Subtab 

Field
Description

Alarm Profile

Select the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Port Number

Displays the port number.

Alarm Profile

Displays the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.1.4.7.11  Loopback Subtab

The Loopback subtab allows you to view and update DS-3 loopback information.

Table C-76  Field Descriptions for the Loopback Subtab 

Field
Description

Port Number

Displays the port number.

Administration State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or Facility (Line), or clear the current loopback (none).

Note The line state must be OOS_MT before you can configure the loopback type.

Inhibit FE Loopback

When selected, inhibits far-end loopback.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Send AIS on Facility Loopback

When selected, sends AIS on the facility loopback.

Send AIS on Terminal Loopback

When selected, sends AIS on the terminal loopback.


C.1.4.7.12  J1 Path Trace Subtab

The J1 Path Trace subtab allows you to view and retrieve J1 path trace information.

Table C-77  Field Descriptions for the J1 Path Trace Subtab 

Field
Description

Port Number

Displays the port number.

STS Number

Displays the synchronous transport signal number.

Expected String

Displays the current expected string.

Received String

Displays the current received string.

Mode

Displays the path trace mode (Off/None, Auto, or Manual).

C2

Represents a machine-generated J1/J2 payload label byte.

Display

Click the Display button to view the circuit trace information. See 7.2.21.6  Viewing a J1 Path Trace from the NE Explorer, page 7-167 for more information.

Retrieve

Click the Retrieve button to retrieve J1 path trace information.


C.1.4.7.13  Customer Info Subtab

The Customer Info subtab displays customer information.

Table C-78 Field Descriptions for the Customer Info Subtab 

Field
Description

STS Number

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.4.8  EC1 Tab

The EC1 tab allows you to view node near-end and far-end performance on an EC1 card to detect possible performance problems. The EC1 tab contains the following subtabs:

Line Config Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

Path Thresh 15 Min Subtab

Path Thresh 1 Day Subtab

STS Config Subtab

Alarm Behavior Subtab

Loopback Subtab

J1 Path Trace Subtab

Customer Info Subtab

C.1.4.8.1  Line Config Subtab

The Line Config subtab allows you to view and change the line settings of the EC1 card.

Table C-79 Field Descriptions for the Line Config Subtab 

Field
Description

Port Number

Displays the port number for the optical port.

Port Name

Allows you to add a name for the optical port.

SD BER

Sets the signal degrade bit error rate.

SF BER

Sets the signal fail bit error rate.

PJSTSMon#

Sets the STS that will be used for pointer justification. If set to 0, no STS is monitored. Only one STS can be monitored on each OC-N port.

0 (default)-3 (OC-3, per port)

0 (default)-12 (OC-12)

0 (default)-48 (OC-48)

Line Length (feet)

Defines the distance (in feet) from backplane connection to the next termination point. Values are 0 through 225 (default) or 226 through 450.

Rx Equalization

For early EC1 card versions, equalization can be turned off if the line length is short or the environment is extremely cold; Rx Equalization should normally be set to On (checked, default).

Administration State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

AINS Soak Count Down

Automatic in-service soak countdown. Displays the remaining time of valid input signal in hh:mm format, after which the card becomes in service (IS) automatically.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.


C.1.4.8.2  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the near- and far-end 15-minute threshold settings of the EC1 card.

Table C-80 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line.

FC-L

Displays the failure count line.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line.

FC-L

Displays the failure count line.


C.1.4.8.3  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the near- and far-end 1-day threshold settings of the EC1 card.

Table C-81 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line.

FC-L

Displays the failure count line.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line.

FC-L

Displays the failure count line.


C.1.4.8.4  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change the near-end 15-minute section threshold information on the EC1 card.

Table C-82 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.


C.1.4.8.5  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change the near-end 1-day section threshold information on the EC1 card.

Table C-83 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.


C.1.4.8.6  Path Thresh 15 Min Subtab

The Path Thresh 15 Min subtab allows you to view and change near- and far-end 15-minute path threshold information on the EC1 card.

Table C-84 Field Descriptions for the Path Thresh 15 Min Subtab 

Field
Description
Near End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

PPJC-Pdet

Displays positive pointer justification count-VC4 path detected.

NPJC-Pdet

Displays negative pointer justification count-VC4 path detected.

PPJC-Pgen

Displays positive pointer justification count-VC4 path generated.

NPJC-Pgen

Displays negative pointer justification count-VC4 path generated.

PJCS-Pdet

Indicates the number of pointer justification count seconds (PJCS) detected on a particular path.

PJCS-Pgen

Indicates the number of pointer justification count seconds generated for a particular path.

PJC-Diff

Displays the sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.

Far End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

PPJC-Pdet

Displays positive pointer justification count-VC4 path detected.

NPJC-Pdet

Displays negative pointer justification count-VC4 path detected.

PPJC-Pgen

Displays positive pointer justification count-VC4 path generated.

NPJC-Pgen

Displays negative pointer justification count-VC4 path generated.

PJCS-Pdet

Indicates the number of pointer justification count seconds (PJCS) detected on a particular path.

PJCS-Pgen

Indicates the number of pointer justification count seconds generated for a particular path.

PJC-Diff

Displays the sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.


C.1.4.8.7  Path Thresh 1 Day Subtab

The Path Thresh 1 Day subtab allows you to view and change near- and far-end 1-day path threshold information on the EC1 card.

Table C-85 Field Descriptions for the Path Thresh 1 Day Subtab 

Field
Description
Near End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

FC-P

Displays the failure count path information.

PPJC-Pdet

Displays positive pointer justification count-VC4 path detected.

NPJC-Pdet

Displays negative pointer justification count-VC4 path detected.

PPJC-Pgen

Displays positive pointer justification count-VC4 path generated.

NPJC-Pgen

Displays negative pointer justification count-VC4 path generated.

PJCS-Pdet

Indicates the number of pointer justification count seconds (PJCS) detected on a particular path.

PJCS-Pgen

Indicates the number of pointer justification count seconds generated for a particular path.

PJC-Diff

Displays the sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.

Far End

STS Number

Displays the synchronous transport signal number.

CV-P

Displays the coding violations path information.

ES-P

Displays the errored seconds path information.

SES-P

Displays the severely errored seconds path information.

UAS-P

Displays the unavailable seconds path information.

PPJC-Pdet

Displays positive pointer justification count-VC4 path detected.

NPJC-Pdet

Displays negative pointer justification count-VC4 path detected.

PPJC-Pgen

Displays positive pointer justification count-VC4 path generated.

NPJC-Pgen

Displays negative pointer justification count-VC4 path generated.

PJCS-Pdet

Indicates the number of pointer justification count seconds (PJCS) detected on a particular path.

PJCS-Pgen

Indicates the number of pointer justification count seconds generated for a particular path.

PJC-Diff

Displays the sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.


C.1.4.8.8  STS Config Subtab

The STS Config subtab allows you to view and change the STS settings of the EC1 card.

Table C-86 Field Descriptions for the STS Config Subtab 

Field
Description

STS Number

Displays the synchronous transport signal number information.

IPPM Enabled

Check to enable intermediate path performance monitoring (IPPM) and uncheck to disable IPPM.


C.1.4.8.9  Alarm Behavior Subtab

The Alarm Behavior subtab allows you to view and change EC1 alarm profile information.

Table C-87 Field Descriptions for the Alarm Behavior Subtab 

Field
Description

Alarm Profile

Select the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Port Number

Displays the port number.

Alarm Profile

Displays the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.1.4.8.10  Loopback Subtab

The Loopback subtab allows you to view and change EC1 loopback information.

Table C-88 Field Descriptions for the Loopback Subtab 

Field
Description

Port Number

Displays the port number.

Administration State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or Facility (Line), or clear the current loopback (none).

Note The line state must be OOS_MT before you can configure the loopback type.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Send AIS on Facility Loopback

When selected, sends AIS on the facility loopback.

Send AIS on Terminal Loopback

When selected, sends AIS on the terminal loopback.


C.1.4.8.11  J1 Path Trace Subtab

The J1 Path Trace subtab allows you to view and retrieve J1 path trace information.

Table C-89 Field Descriptions for the J1 Path Trace Subtab 

Field
Description

Port Number

Displays the port number.

STS Number

Displays the synchronous transport signal number.

Expected String

Displays the current expected string.

Received String

Displays the current received string.

Mode

Displays the path trace mode (Off/None, Auto, or Manual).

C2

Represents a machine-generated J1/J2 payload label byte.

Display

Click the Display button to view the circuit trace information. See 7.2.21.6  Viewing a J1 Path Trace from the NE Explorer, page 7-167 for more information.

Retrieve

Click the Retrieve button to retrieve J1 path trace information.


C.1.4.8.12  Customer Info Subtab

The Customer Info subtab displays customer information.

Table C-90 Field Descriptions for the Customer Info Subtab 

Field
Description

STS Number

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.4.9  Optical Tab

The Optical tab allows you to view node near-end and far-end performance on an optical card to detect possible performance problems. The Optical tab contains the following subtabs:

Line Config Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

Physical Thresh 15 Min Subtab

Physical Thresh 1 Day Subtab

STS Config Subtab

Alarm Behavior Subtab

Loopback Subtab

Auto Laser Shutdown Subtab

Protection Subtab

J1 Path Trace Subtab

Customer Info Subtab

C.1.4.9.1  Line Config Subtab

The Line Config subtab allows you to view and change the line settings of an optical card.

Table C-91 Field Descriptions for the Line Config Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a name for the optical port.

Port Rate

Sets the rate of the new port.

SD BER

Sets the signal degrade bit error rate.

SF BER

Sets the signal fail bit error rate.

Type

Defines the port as SONET or SDH.

PJSTSMon#

Sets the STS that will be used for pointer justification. If set to 0, no STS is monitored. Only one STS can be monitored on each OC-N port.

0 (default)-3 (OC-3, per port)

0 (default)-12 (OC-12)

0 (default)-48 (OC-48)

Provides Sync

When checked, the card is provisioned as an NE timing reference.

EnableSyncMsg

Enables synchronization status messages (S1 byte), which allow the node to choose the best timing source.

SendDoNotUse

When checked, sends a do not use (DUS) message on the S1 byte.

Administration State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

AINS Soak Count Down

Automatic in-service soak countdown. Displays the remaining time of valid input signal in hh:mm format, after which the card becomes in service (IS) automatically.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Admin SSM

If the node does not receive an SSM signal, it defaults to synchronization traceability unknown (STU). Admin SSM allows you to override the STU value with one of the following:

PRS—Primary reference source (Stratum 1)

STS2—Stratum 2

TNC—Transit node clock

STS3E—Stratum 3E

STS3—Stratum 3

SMC—SONET minimum clock

ST4—Stratum 4

Send <FF> DoNotUse

When checked, sends a do not use (DUS) (0xff) message on the S1 byte.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency. The Wavelength column lists the correct wavelengths, depending on the type of card and the band selected.


C.1.4.9.2  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the near- and far-end 15-minute threshold settings of an optical card.

Table C-92 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.

PSC

In a 1 + 1 protection scheme for a working card, protection switching count (PSC) is a count of the number of times service switches from a working card to a protection card plus the number of times service switches back to the working card. For a protection card, PSC is a count of the number of times service switches to a working card from a protection card plus the number of times service switches back to the protection card. The PSC PM is applicable only if revertive line-level protection switching is used. PSC is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

PSD

Protection switching duration (PSD) applies to the length of time, in seconds, that service is carried on another line. For a working line, PSD is a count of the number of seconds that service was carried on the protection line. For the protection line, it is a count of the seconds that the line was used to carry service. The PSD PM is applicable only if revertive line-level protection switching is used. PSD is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.


C.1.4.9.3  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the near- and far-end 1-day threshold settings of an optical card.

Table C-93 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.

PSC

In a 1 + 1 protection scheme for a working card, protection switching count (PSC) is a count of the number of times service switches from a working card to a protection card plus the number of times service switches back to the working card. For a protection card, PSC is a count of the number of times service switches to a working card from a protection card plus the number of times service switches back to the protection card. The PSC PM is applicable only if revertive line-level protection switching is used. PSC is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

PSD

Protection switching duration (PSD) applies to the length of time, in seconds, that service is carried on another line. For a working line, PSD is a count of the number of seconds that service was carried on the protection line. For the protection line, it is a count of the seconds that the line was used to carry service. The PSD PM is applicable only if revertive line-level protection switching is used. PSD is supported in revertive and nonrevertive modes.

Note This parameter is not supported for transponder or muxponder cards.

Far End

Port Number

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Failure count line (FC-L) lists a count of the number of near-end line failure events. A failure event begins when an AIS-L failure is declared, or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.


C.1.4.9.4  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change the near-end 15-minute section threshold settings of an optical card.

Table C-94 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.


C.1.4.9.5  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change the near-end 1-day section threshold settings of an optical card.

Table C-95 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.


C.1.4.9.6  Physical Thresh 15 Min Subtab

The Physical Thresh 15 Min subtab allows you to view and change 15-minute physical threshold information on an optical card.

Table C-96 Field Descriptions for the Physical Thresh 15 Min Subtab 

Field
Description

Port No.

Pluggable entity number and port number.

LBC-HIGH

Maximum laser bias current. The default is (15 min): 200 percent.

LBC-LOW

Minimum laser bias current. The default is (15 min): 20 percent.

OPT-HIGH

Maximum optical power transmitted. The default is (15 min): 120 percent.

OPT-LOW

Minimum optical power transmitted. The default is (15 min): 80 percent.

OPR-HIGH

Maximum optical power received. The default is (15 min): 200 percent.

OPR-LOW

Minimum optical power received. The default is (15 min): 50 percent.

Set OPR

Setting the optical power received (OPR) establishes the received power level as 100 percent. If the received power decreases, then the OPR percentage decreases to reflect the loss in received power. For example, if the received power decreases 3-dBm, the OPR decreases 50 percent.


C.1.4.9.7  Physical Thresh 1 Day Subtab

The Physical Thresh 1 Day subtab allows you to view and change 1-day physical threshold information on an optical card.

Table C-97 Field Descriptions for the Physical Thresh 1 Day Subtab 

Field
Description

Port No.

Pluggable entity number and port number.

LBC-HIGH

Maximum laser bias current. The default is (15 min): 200 percent.

LBC-LOW

Minimum laser bias current. The default is (15 min): 20 percent.

OPT-HIGH

Maximum optical power transmitted. The default is (15 min): 120 percent.

OPT-LOW

Minimum optical power transmitted. The default is (15 min): 80 percent.

OPR-HIGH

Maximum optical power received. The default is (15 min): 200 percent.

OPR-LOW

Minimum optical power received. The default is (15 min): 50 percent.

Set OPR

Setting the OPR establishes the received power level as 100 percent. If the received power decreases, then the OPR percentage decreases to reflect the loss in received power. For example, if the received power decreases 3-dBm, the OPR decreases 50 percent.


C.1.4.9.8  STS Config Subtab

The STS Config subtab allows you to view and change the STS settings of an optical card.

Table C-98  Field Descriptions for the STS Config Subtab 

Field
Description

STS Number

Displays the synchronous transport signal number information.

IPPM Enabled

Check to enable IPPM and uncheck to disable IPPM.

XC Loopback

Displays the cross-connect loopback status.


C.1.4.9.9  Alarm Behavior Subtab

The Alarm Behavior subtab allows you to view and change optical card alarm profile information.

Table C-99  Field Descriptions for the Alarm Behavior Subtab 

Field
Description

Alarm Profile

Select the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Port Number

Displays the port number.

Alarm Profile

Displays the alarm profile for the port.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.1.4.9.10  Loopback Subtab

The Loopback subtab allows you to view and change optical card loopback information.

Table C-100 Field Descriptions for the Loopback Subtab 

Field
Description

Port Number

Displays the port number.

Administration State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or Facility (Line), or clear the current loopback (none).

Note The line state must be OOS_MT before you can configure the loopback type.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Send AIS on Facility Loopback

When selected, sends AIS on the facility loopback.

Send AIS on Terminal Loopback

When selected, sends AIS on the terminal loopback.


C.1.4.9.11  Auto Laser Shutdown Subtab

The Auto Laser Shutdown subtab allows you to view and update optical card auto laser shutdown (ALS) parameters.

Table C-101 Field Descriptions for the Auto Laser Shutdown Subtab 

Field
Description

Port Number

Displays the port number.

ASL Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.


C.1.4.9.12  Protection Subtab

The Protection subtab allows you to view and update protection group information.

Table C-102 Field Descriptions for the Protection Subtab 

Field
Description

Protection Groups

Displays a list of available protection groups.

Protection Group Details

Displays details about the selected protection groups, such as which port is the protected port and which port is the working port. Also allows you to execute switch commands.

Switch Commands

Allows you to perform a manual switch, perform a forced switch, or clear the existing command switching.

Inhibit Switching

Allows you to inhibit unlock switching, lock-out switching, or lock-on switching.


C.1.4.9.13  J1 Path Trace Subtab

The J1 Path Trace subtab allows you to view and retrieve J1 path trace information.

Table C-103 Field Descriptions for the J1 Path Trace Subtab 

Field
Description

Port Number

Displays the port number.

STS Number

Displays the synchronous transport signal number.

Expected String

Displays the current expected string.

Received String

Displays the current received string.

Mode

Displays the path trace mode (Off/None, Auto, or Manual).

C2

Represents a machine-generated J1/J2 payload label byte.

Display

Click the Display button to view the circuit trace information. See 7.2.21.6  Viewing a J1 Path Trace from the NE Explorer, page 7-167 for more information.

Retrieve

Click the Retrieve button to retrieve J1 path trace information.


C.1.4.9.14  Customer Info Subtab

The Customer Info subtab displays customer information.

Table C-104 Field Descriptions for the Customer Info Subtab 

Field
Description

STS Number

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.4.10  Alarm Extenders Tab

The Alarm Extenders tab allows you to view CTX-CL600 alarm information. The Alarm Extenders tab contains the following subtabs:

External Alarms Subtab

External Controls Subtab

User-Defined Alarms Subtab

C.1.4.10.1  External Alarms Subtab

The External Alarms subtab allows you to view and update external alarm information.

Table C-105 Field Descriptions for the External Alarms Subtab 

Field
Description

Input Number

The alarm input number.

Enabled

Check to activate the fields for the alarm input number.

Alarm Type

Choose an alarm type from the provided list.

Severity

Choose a severity from the list.

Raised When

Choose the contact condition that will trigger the alarm in CTC.

Virtual Wire

To assign the external device to a virtual wire, choose a virtual wire from the list, or choose None if no assignment is required.

Description

A default description is provided in this line for every external alarm that is enabled.

Raised

Indicates if an alarm has been raised.

Contact Status

Indicates the current status of the contact.


C.1.4.10.2  External Controls Subtab

The External Controls subtab allows you to view and update external controls.

Table C-106 Field Descriptions for the External Controls Subtab 

Field
Description

Control Number

The control number.

Enabled

Check to activate the fields for the control number.

Control Type

Choose a control type from the provided list.

Trigger Type

Choose a trigger type: a local minor, major, or critical alarm; a remote minor, major, or critical alarm; or a virtual wire activation.

Description

Enter a description.

Current State

The current state of the control.

Auto State

The auto state of the control.

Contact Setting

The current contact setting.


C.1.4.10.3  User-Defined Alarms Subtab

The User-Defined Alarms subtab allows you to view, add, and delete custom alarm types on CTX-CL600 cards.

Table C-107 Field Descriptions for the User-Defined Alarms Subtab 

Field
Description

Alarm Types

Lists the user-defined alarm types that have been created on the CTX-CL600 card. You can create up to 50 custom environmental alarms, which are reported in the Condition column in the Alarm Log and Alarm Browser windows.

Add

Click the Add button to add a new custom alarm type. Enter a unique alarm type name that contains 20 characters or fewer. Only the following characters are valid: 0-9, A-Z, a-z, and hyphen (-).

Delete

Click the Delete button to delete an existing alarm type.


C.1.4.11  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the CTX-CL600 module.

Table C-108 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.5  Slot Properties—FILLER

The slot properties pane displays information about the ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, ONS 15454 SDH, ONS 15600 SONET, or ONS 15600 SDH slot that is selected in the NE Explorer tree. For the FILLER module, the slot properties pane displays the Module View tab.

C.1.5.1  Module View Tab

The Module View tab displays a graphic of the FILLER card that is installed in the slot. Right-clicking the graphic opens a shortcut menu that you can use to add a card.

C.1.6  Slot Properties—MIC-28-3-A and MIC-28-3-B

The slot properties pane displays information about the Cisco ONS 15327 slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The MIC-28-3-A and MIC-28-3-B cards are the Mechanical Interface Cards (MICs). The MICs provide the physical connection points for the DS-1 and DS-3 interfaces on the XTC cards, the redundant power inputs, the alarm inputs and outputs, and the BITS timing inputs and outputs.

For the MIC module, the slot properties pane displays Module View and Identification tabs.

C.1.6.1  Module View Tab

The Module View tab displays a graphic of the MIC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.6.2  Identification Tab

The Identification tab allows you to view and update MIC identification information.

Table C-109 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.7  Slot Properties—MMU (ONS 15454 SONET and ONS 15454 SDH)

The slot properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Multi-Ring/Mesh Upgrade Unit (MMU) supports multiring and mesh upgrades for reconfigurable optical add/drop (ROADM) nodes in both the C-band and the L-band. Mesh/multiring upgrade is the capability to optically bypass a given wavelength from one section of the network or ring to another one without requiring 3R regeneration. In each node, you need to install two MMUs, one on the east side and one on the west side. You can install the MMU card in slots 1 through 6 and 12 through 17.

The MMU has six ports:

EXP RX port—Receives the optical signal from the ROADM section available on the NE.

EXP TX port—Sends the optical signal to the ROADM section available on the NE.

EXP-A RX port—Receives the optical signal from the ROADM section available on other NEs or rings.

EXP-A TX port—Sends the optical signal to the ROADM section available on other NEs or rings.

COM TX port—Sends the optical signal to the fiber stage section.

COM RX port—Receives the optical signal from the fiber stage section.

The following figure shows the card faceplate.

Figure C-2 MMU Faceplate and Ports

For the MMU module, the slot properties pane displays the following tabs: Module View, Identification, Optical Line, and Inventory.

C.1.7.1  Module View Tab

The Module View tab displays a graphic of the card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.7.2  Identification Tab

The Identification tab allows you to view and update card identification information.

Table C-110 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

Displays the administration state. The state can either be Unlocked or Locked, Maintenance.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.7.3  Optical Line Tab

The Optical Line tab allows you to view and update optical channel threshold information. The tab contains the following subtabs:

Parameters Subtab

Warning Thresh 15 Min Subtab

Warning Thresh 1 Day Subtab

Alarm Thresh Subtab

C.1.7.3.1  Parameters Subtab

The Parameters subtab provides information on the status and directions specified for the optical connectors.

Table C-111 Field Descriptions for the Parameters Subtab 

Field
Description

Port Number

Displays the identifier of the port (and specific channel information: Add, Drop, Tx, or Rx).

Type

Displays the port type.

Port Name

Allows you to assign the specified port a user-defined name. The port name can be up to 32 alphanumeric or special characters. The port name is blank by default.

Administration State

Displays the status of the channel. Values are:

IS—In Service; able to carry traffic.

OOS_DSBLD—Out of Service-Disabled. Unable to carry traffic.

IS_AINS—In Service-Auto In Service. Alarm reporting is suppressed, but traffic is carried.

OOS_MT—Out of Service-Maintenance. Alarm reporting is suppressed, but traffic is carried and loopbacks are allowed.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Line Direction (available in CTM R7.2 and earlier)

Allows you to associate a card with the line direction. Use this field if you have two cards on the same shelf and must designate which one will carry the traffic flow from east-to-west. The second card will carry traffic from west-to-east.

Type

Identifies the type of port, such as Output Express, Input Express, Output COM, Input COM, and Drop.

Power

Shows the current power level per port.


C.1.7.3.2  Warning Thresh 15 Min Subtab

The Warning Thresh 15 Min subtab allows you to set thresholds for 15-minute threshold crossing alert (TCA) generation.

Table C-112 Field Descriptions for the Warning Thresh 15 Min Subtab 

Field
Description

Port Number

Displays the identifier of the port (and specific channel information: Add, Drop, Tx, or Rx).

Type

Displays the port type.

Power Low (dBm)

Allows you to set the low power settings.

Power High (dBm)

Allows you to set the high power settings.


C.1.7.3.3  Warning Thresh 1 Day Subtab

The Warning Thresh 1 Day subtab allows you to set thresholds for 1-day threshold crossing alert generation.

Table C-113 Field Descriptions for the Warning Thresh 1 Day Subtab 

Field
Description

Port Number

Displays the identifier of the port (and specific channel information: Add, Drop, Tx, or Rx).

Type

Displays the port type.

Power Low (dBm)

Allows you to set the low power settings.

Power High (dBm)

Allows you to set the high power settings.


C.1.7.3.4  Alarm Thresh Subtab

The Alarm Thresh subtab allows you to select thresholds for alarm generation.

Table C-114 Field Descriptions for the Alarm Thresh Subtab 

Field
Description

Port Number

The port number.

Power Failure Low (dBm)

Allows you to set the low power failure settings.


C.1.7.4  Inventory Tab

The Inventory tab allows you to view the card inventory information.

Table C-115 Field Descriptions for the Inventory Tab 

Field
Description

Attribute

Displays the object that can be inventoried.

Value

Displays the value of the object that is inventoried.

Units

Displays the unit of measure (when applicable) of the object that is inventoried.


Table 1-23 on page 1-49


Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.8  Slot Properties—OSCM (ONS 15454 SONET and ONS 15454 SDH)

The slot properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Optical Service Channel Modem (OSCM) module is a single-slot card with a 1510 nm OC-3 optical transceiver interface. The OSCM features a variable optical attenuator (VOA) in the transmit path and a 100BASE-T FE user data channel. The OSCM also distributes the synchronous clock to all NEs on the ring.

The following figure shows the block diagram.

Figure C-3 OSCM Module

For the OSCM module, the slot properties pane displays the following tabs: Module View, Identification, Line, Optical Line, Inventory, and Alarm Behavior.

C.1.8.1  Module View Tab

The Module View tab displays a graphic of the card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.8.2  Identification Tab

The Identification tab allows you to view and update card identification information.

Table C-116 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.8.3  Line Tab

The Line tab allows you to view and update line card information.

Table C-117 Field Descriptions for the Line Tab 

Field
Description
Line Config

Port No.

The port number.

Port Name

The port name.

SD BER

The signal degrade bit error rate.

SF BER

The signal fail bit error rate.

Type

The port type (SONET or SDH).

PJSTSMon#

The STS that will be used for pointer justification. If set to zero, no STS is used.

ProvidesSync

When checked, the card is provisioned as an NE timing reference.

EnableSyncMsg

Enables synchronization status messages (S1 byte), which allow the node to choose the best timing source.

Send DoNotUse

When checked, sends a do not use (DUS) message on the S1 byte.

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

AINS Soak

Auto in service soak. The determination of duration left before the traffic/termination transitions to IS state.

Line Thresh 15 Minute - Near End, Far End

Port No.

The port number.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

CV-L

Coding violations line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Line Thresh 1 Day - Near End, Far End

Port No.

The port number.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

CV-L

Coding violations line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Section Thresh 15 Min, Near End

Port No.

The port number.

CV-S

Coding violations section.

ES-S

Errored seconds section.

SES-S

Severely errored seconds section.

SEFS-S

Severely errored framing seconds section.

Section Thresh 1 Day, Near End

Port No.

The port number.

CV-S

Coding violations section.

ES-S

Errored seconds section.

SES-S

Severely errored seconds section.

SEFS-S

Severely errored framing seconds section.


C.1.8.4  Optical Line Tab

The Optical Line tab allows you to view and update optical line threshold information.

Table C-118 Field Descriptions for the Optical Line Tab 

Subtab
Description
Parameters

Port Number

The port number.

Port Name

The port name.

Status

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Active Channels

Indicates how many channels the amplifier is carrying. The value generally reflects the number of provisioned channels.

Line Direction (available in CTM R7.2 and earlier)

The direction of the line (west-to-east or east-to-west).

Type

The port type.

Power

The laser power.

VOA Mode

Shows the current functional mode of the VOA: constant gain mode, constant power mode, or not in use (N/A).

VOA Power Ref

The VOA reference power.

VOA Power Calib

The VOA calibration power.

VOA Attenuation Ref

The VOA reference attenuation.

OSC Power

Shows the current optical service channel (OSC) power level per port.

VOA Attenuation Calib

The VOA calibration attenuation.

Warning Thresh 15 Min

Port Number

The port number.

Type

Identifies the type of port, such as Output Express, Input Express, Output COM, Input COM, and Drop.

Power Low

The lower power threshold.

Power High

The upper power threshold.

OSC Power Low

Allows you to set the low OSC power threshold.

OSC Power High

Allows you to set the high OSC power threshold.

Warning Thresh 1 Day

Port Number

The port number.

Type

Identifies the type of port, such as Output Express, Input Express, Output COM, Input COM, and Drop.

Power Low

The lower power threshold.

Power High

The upper power threshold.

OSC Power Low

Allows you to set the low OSC power threshold.

OSC Power High

Allows you to set the high OSC power threshold.

Alarm Threshold

Port Number

The port number.

Power Failure Low

The lower power failure threshold.

Power Degrade High

The upper power degrade threshold.

Power Degrade Low

The lower power degrade threshold.

VOA Degrade High

The upper VOA degrade threshold.

VOA Degrade Low

The lower VOA degrade threshold.

OSC Power Failure Low

Allows you to set the low OSC power failure threshold.

OSC Power Failure High

Allows you to set the high OSC power failure threshold.

OSC Power Degrade Low

Allows you to set the low OSC power degrade threshold.

OSC Power Degrade High

Allows you to set the high OSC power degrade threshold.


C.1.8.5  Inventory Tab

The Inventory tab allows you to view the card inventory information.

Table C-119 Field Descriptions for the Inventory Tab 

Field
Description

Serial Number

The serial number that is unique to each card.

IL-REF

The reference insertion loss.

Part Number

The part number that is printed on the top of the card.

Firmware Version

The revision number of the software used by the ASIC chip installed on the card.

Vendor ID

The ID of the vendor.

Hardware Version

The hardware version number.


C.1.8.6  Alarm Behavior Tab

The Alarm Behavior tab allows you to view and update card alarm profile information.

Table C-120 Field Descriptions for the Alarm Behavior Tab 

Field
Description

Alarm Profile

Displays the alarm profile that has been configured for the card.

Suppress Alarms

When checked, indicates that all alarms are suppressed for the card.

Port Number

Displays the card port number.

Alarm Profile

Choose an alarm profile for the port from the drop-down list. Values are Default, Inherited, or a customized alarm profile.

Suppress Alarms

When checked, all alarms are suppressed for the port.

Alarm Profile

Choose an alarm profile for all ports.

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.9  Slot Properties—SSXC

The slot properties pane displays information about the Cisco ONS 15600 SONET and ONS 15600 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The SSXC card provides a fully nonblocking 6144 bidirectional STS-1 matrix.


Note In NE releases earlier than release 5.0, the SSXC card is called the CXC card.


For the SSXC, the slot properties pane displays Module View and Identification tabs.

C.1.9.1  Module View Tab

The Module View tab displays a graphic of the SSXC card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.9.2  Identification Tab

The Identification tab allows you to view and update SSXC identification information.

Table C-121 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

User Code

Allows you to enter an ASCII string to identify the card. The user code is stored in nonvolatile memory so that it is not lost when the unit is moved or stored as a spare.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.10  Slot Properties—TCC+

The slot properties pane displays information about the Cisco ONS 15327 or ONS 15454 slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Timing Communication and Control+ (TCC+) card performs system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SONET data communications channel (DCC) termination, and system fault detection for the ONS 15327 and ONS 15454. The TCC+ also ensures that the system maintains Telcordia timing requirements.

For the TCC+ module, the slot properties pane displays Module View and Identification tabs.

C.1.10.1  Module View Tab

The Module View tab displays a graphic of the TCC+ that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s).

C.1.10.2  Identification Tab

The Identification tab allows you to view and update TCC+ identification information.

Table C-122 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.11  Slot Properties—TCC-I

The slot properties pane displays information about the Cisco ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Timing Communication and Control-International (TCC-I) Card performs system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SONET data communications channel (DCC) termination, and system fault detection for the ONS 15454 SDH. The TCC-I also ensures that the system maintains Telcordia timing requirements.

For the TCC-I module, the slot properties pane displays Module View and Identification tabs.

C.1.11.1  Module View Tab

The Module View tab displays a graphic of the TCC-I that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to add, delete, change, or reset the module.

C.1.11.2  Identification Tab

The Identification tab allows you to view and update TCC-I identification information.

Table C-123 Field Descriptions for the Identification Tab

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for; for example, TCC+ or TCC-I.

Actual Equipment Type

Displays the actual card that is installed in the slot; for example, TCC+ or TCC-I.

HW Part No

Displays the part number that is printed on the top of the card.

HW Hardware Revision

Displays the card revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the hardware revision number of the software used by the ASIC chip installed on the card.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.12  Slot Properties—TCC2

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Advanced Timing, Communications, and Control (TCC2) performs system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SDH section overhead (SOH) data communication channel/generic communication channel (DCC/GCC) termination, and system fault detection for the ONS 15454 SDH. The TCC2 also ensures that the system maintains Stratum 3E (ITU-T G.813) timing requirements. It monitors the supply voltage of the system. The TCC2 card can work with the XC10G, XC-VXL-10G, or XC-VXL-2.5G cross-connect cards. It requires software release 5.0 or later.

For the TCC2 module, the slot properties pane displays the following tabs: Module View, Identification, and Info.

C.1.12.1  Module View Tab

The Module View tab displays a graphic of the TCC2 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.12.2  Identification Tab

The Identification tab allows you to view and update TCC2 identification information.

Table C-124 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.12.3  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the TCC2 card.

Table C-125 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.13  Slot Properties—TCC2P

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Advanced Timing, Communications, and Control Plus (TCC2P) card is an enhanced version of the TCC2 card. The primary enhancements are Ethernet security features and 64K composite clock BITS timing.

The TCC2P card performs system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SONET SOH DCC/GCC termination, and system fault detection for the ONS 15454. The TCC2P also ensures that the system maintains Stratum 3 (Telcordia GR-253-CORE) timing requirements. It monitors the supply voltage of the system.


Note The TCC2P card requires software release 5.0 or later.


For the TCC2P module, the slot properties pane displays the following tabs: Module View, Identification, and Info.

C.1.13.1  Module View Tab

The Module View tab displays a graphic of the TCC2P that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.13.2  Identification Tab

The Identification tab allows you to view and update TCC2P identification information.

Table C-126 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

Displays the administration state. The state can either be Unlocked or Locked, Maintenance.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.13.3  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the TCC2P card.

Table C-127 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.14  Slot Properties—TSC (ONS 15600 SONET and ONS 15600 SDH)

The slot properties pane displays information about the Cisco ONS 15600 SONET or ONS 15600 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The timing and shelf controller (TSC) card performs all system-timing functions for each ONS 15600. The TSC card monitors the recovered clocks from each traffic card and two building integrated timing supply (BITS) interfaces for frequency accuracy.

For the TSC module, the slot properties pane displays Module View and Identification tabs.

C.1.14.1  Module View Tab

The Module View tab displays a graphic of the TSC card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.14.2  Identification Tab

The Identification tab allows you to view and update TSC identification information.

Table C-128 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

User Code

Allows you to enter an ASCII string to identify the card. The user code is stored in nonvolatile memory so that it is not lost when the unit is moved or stored as a spare.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.15  Slot Properties—Unprovisioned Slot (ONS 15327 and ONS 15454 SONET)

The slot properties pane displays information about the Cisco ONS 15327 or ONS 15454 SONET subrack slot that is selected in the NE Explorer tree. Unprovisioned slots are slots that are not polled by the TCC. Unprovisioned slots display a Module View tab.

C.1.15.1  Module View Tab

The Module View tab displays a graphic of the ONS 15327 or ONS 15454 SONET slot that is selected in the NE Explorer tree. For unprovisioned slots, a blank slot graphic is displayed.


Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.16  Slot Properties—Unprovisioned Slot (ONS 15454 SDH)

The slot properties pane displays information about the Cisco ONS 15454 SDH subrack slot that is selected in the NE Explorer tree. Unprovisioned slots are slots that are not polled by the TCC. Unprovisioned slots display a Module View tab.

C.1.16.1  Module View Tab

The Module View tab displays a graphic of the ONS 15454 SDH slot that is selected in the NE Explorer tree. For unprovisioned slots, a blank slot graphic is displayed.


Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.17  Slot Properties—XC

The slot properties pane displays information about the Cisco ONS 15327 or ONS 15454 SONET slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The ONS 15327 or ONS 15454 Cross-Connect (XC) card performs port-to-port time-division multiplexing (TDM), STS switching, and can terminate 288 STSs, or 144 STS cross-connections. Each STS cross-connection uses two STS ports on the XC card STS matrix.

For the XC module, the slot properties pane displays the following tabs: Module View, Identification, and Protection.

C.1.17.1  Module View Tab

The Module View tab displays a graphic of the XC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to add, delete, change, or reset the module.

C.1.17.2  Identification Tab

The Identification tab allows you to view and update XC identification information.

Table C-129 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.17.3  Protection Tab

The Protection tab allows you to view and update XC protection group information.

Table C-130 Field Descriptions for the Protection Tab 

Field
Description

State of Slot x

Displays the state of the selected slot and of the companion XC slot.

Switch

Click to switch the selected slot from its current state to the other states.

Lock

Click to lock the selected slot into its current state.

Unlock

Click to unlock the current slot from its current state.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.18  Slot Properties—XC-VXL-10G

The slot properties pane displays information about the Cisco ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The XC-VXL-10G card cross-connects E-1, E-3, DS-3, STM-1, STM-4, STM-16, and STM-64 signal rates. The XC-VXL-10G provides a maximum of 384 x 384 VC-4 nonblocking cross-connections, 384 x 384 VC-3 nonblocking cross-connections, or 2016 x 2016 VC-12 nonblocking cross-connections. It is designed for 10-Gb/s solutions.

For the XC-VXL-10G module, the slot properties pane displays the following tabs: Module View, Identification, and Protection.

C.1.18.1  Module View Tab

The Module View tab displays a graphic of the XC-VXL-10G that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to add, delete, change, or reset the module.

C.1.18.2  Identification Tab

The Identification tab allows you to view and update XC-VXL-10G identification information.

Table C-131 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.18.3  Protection Tab

The Protection tab allows you to view and update XC-VXL-10G protection group information.

Table C-132 Field Descriptions for the Protection Tab 

Field
Description

State of Slot x

Displays the state of the selected slot and of the companion XC-VXL-10G slot.

Switch

Click to switch the selected slot from its current state to the other states.

Lock

Click to lock the selected slot into its current state.

Unlock

Click to unlock the current slot from its current state.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.19  Slot Properties—XC10G

The slot properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

ONS 15454 SONET and ONS 15454 SDH cross-connect cards establish connections and perform time division switching (TDS) at the STS-1 level between ONS 15454 traffic cards. The ONS 15454 SONET and ONS 15454 SDH 10 Gigabit Cross-Connect (XC10G) card cross-connects STS-12, STS-48, and STS-192 signal rates. The XC10G provides a maximum of 1152 STS-1 cross-connections. Any STS-1 on any port can be connected to any other port, which means that the STS cross-connections are nonblocking.

For the XC10G module, the slot properties pane displays the following tabs: Module View, Identification, Protection, and Info.

C.1.19.1  Module View Tab

The Module View tab displays a graphic of the XC10G that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.19.2  Identification Tab

The Identification tab allows you to view and update XC10G identification information.

Table C-133 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.19.3  Protection Tab

The Protection tab allows you to view and update XC10G protection group information.

Table C-134 Field Descriptions for the Protection Tab 

Field
Description

State of Slot x

Displays the state of the selected slot and of the companion XC10G slot.

Switch

Click to switch the selected slot from its current state to the other states.

Lock

Click to lock the selected slot into its current state.

Unlock

Click to unlock the current slot from its current state.


C.1.19.4  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the XC10G card.

Table C-135 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.20  Slot Properties—XCVT

The slot properties pane displays information about the Cisco ONS 15327 or ONS 15454 SONET slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The ONS 15327 or ONS 15454 Cross-Connect Virtual Tributary (XCVT) performs port-to-port time-division multiplexing (TDM), STS and VT1.5 switching, and can terminate 288 STSs, or 144 STS cross-connections. (Each STS cross-connection uses two STS ports on the cross-connect card STS matrix.)

For the XCVT module, the slot properties pane displays the following tabs: Module View, Identification, and Protection.

C.1.20.1  Module View Tab

The Module View tab displays a graphic of the XCVT that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to add, delete, change, or reset the module.

C.1.20.2  Identification Tab

The Identification tab allows you to view and update XCVT identification information.

Table C-136 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for

Actual Equipment Type

Displays the actual card that is installed in the slot.

Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.20.3  Protection Tab

The Protection tab allows you to view and update XCVT protection group information.

Table C-137 Field Descriptions for the Protection Tab 

Field
Description

State of Slot x

Displays the state of the selected slot and of the companion XCVT slot.

Switch

Click to switch the selected slot from its current state to the other states.

Lock

Click to lock the selected slot into its current state.

Unlock

Click to unlock the current slot from its current state.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.21  Slot Properties—XCVXC

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

In the SONET system, the XCVXC card cross-connects STS-1 and VT1.5/VT2 layers. It provides full, nonblocking 1152 x 1152 port STS-1 cross-connections or 2688 x 2688 port VT1.5 cross-connections.

In the SDH system, the XCVXC card cross-connects VC-3, VC-4, and VC-12/VC-11 layers. It provides 384 x 384 VC-3/TUG-3 cross-connections, full, nonblocking 384 x 384 VC-4 (and 4-Nc) cross-connections, or 2016 x 2016 VC-12 cross-connections.

Cross-connect and provisioning information is established through the user interface on the TCC2 card.

For the XCVXC card, the slot properties pane displays the following tabs: Module View, Identification, Protection, and Info.

C.1.21.1  Module View Tab

The Module View tab displays a graphic of the XCVXC card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.21.2  Identification Tab

The Identification tab allows you to view and update XCVXC card identification information.

Table C-138 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

Select the designation that determines whether an entity is in service or out of service. The administration state is the driver for the service state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.21.3  Protection Tab

The Protection tab allows you to view and update XCVXC protection group information.

Table C-139 Field Descriptions for the Protection Tab 

Field
Description

State of Slot x

Displays the state of the selected slot and of the companion XCVXC slot.

Switch

Click to switch the selected slot from its current state to the other states.

Lock

Click to lock the selected slot into its current state.

Unlock

Click to unlock the current slot from its current state.


C.1.21.4  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the XCVXC card.

Table C-140 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.22  Slot Properties—XTC (ONS 15305)

The slot properties pane displays information about the CTC-based ONS 15305 that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Integrated Cross-Connect, Timing, and Control (XTC) cards perform system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SONET data communications channel (DCC) termination, system fault detection, and cross-connect maintenance and management for the ONS 15305 CTC. The XTC cards also provide the circuitry for the DS-1 and DS-3 interfaces and ensure that the system maintains Telcordia timing requirements. An XTC card is required to operate the ONS 15305 CTC and can be used in a redundant or nonredundant configuration.

For the ONS 15305 CTC XTC controller, the slot properties pane displays a single Module View tab.

C.1.22.1  Module View Tab

The Module View tab displays a graphic of the XTC controller that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.23  Slot Properties—XTC (ONS 15327)

The slot properties pane displays information about the Cisco ONS 15327 slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Integrated Cross-Connect, Timing, and Control (XTC) cards perform system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SONET data communications channel (DCC) termination, system fault detection, and cross-connect maintenance and management for the ONS 15327. The XTC cards also provide the circuitry for the DS-1 and DS-3 interfaces and ensure that the system maintains Telcordia timing requirements. An XTC card is required to operate the ONS 15327 and can be used in a redundant or nonredundant configuration.

For the XTC module, the slot properties pane displays the following tabs: Module View, Identification, DS-1, DS-3, STS-1 Path, VT1.5 Path, Alarm Extenders, Protection, and J1 Path Trace.

C.1.23.1  Module View Tab

The Module View tab displays a graphic of the XTC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

C.1.23.2  Identification Tab

The Identification tab allows you to view and update XTC identification information.

Table C-141 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type that the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.1.23.3  DS-1 Tab

The DS-1 tab allows you to view and update XTC DS-1 information.

Table C-142 Field Descriptions for the DS-1 Tab 

Subfield
Description
Line Config

Port Number

Displays the port number:

1 to 14 (XTC-14)

1 to 28 (XTC-28-3)

Port Name

Allows you to enter the name of the port. You can enter up to 32 alphanumeric or special characters. The port name is blank by default.

Line Type

Defines the line framing type as ESF (Extended Super Frame), D4, or unframed.

Line Coding

Allows you to define the DS-1 transmission coding type. Values are:

AMI—Alternate Mark Inversion (default)

B8ZS—Bipolar 8 Zero Substitution

Line Length

Defines the distance (in feet) from backplane connection to the next termination point. Values are:

0-131 (default)

132-262

263-393

394-524

525-655

State

Displays the status of the line. Values are:

IS—In Service

IS_AINS—In Service-Auto In Service Soak

OOS—Out of Service

OOS_MT—Out of Service-Maintenance

AINS Soak

Automatic in-service soak. The amount of valid input signal in hh.mm, after which the port is set in service by the software. The range is from 0 to 48 hours, in 15-minute increments.

AINS Soak Count Down

Displays the remaining time of valid input signal in hh.mm, after which the card becomes in service (IS) automatically. The range is from 0 to 48 hours, in 15-minute increments.

SD BER

Sets the signal degrade bit error rate.

SF BER

Sets the signal fail bit error rate.

Send AIS-V for DS-1 AIS

When checked, sends an Alarm Indication Signal VT (AIS-V) instead of a DS-1 AIS (from the line side toward the backplane/system side) when a line-side trigger occurs.

Raise AIS for LOF

Sends an AIS when a loss of frame (LOF) occurs.

Line Threshold 15 Minutes

Port Number

The port number (1 to 14 for XTC-14; 1 to 28 for XTC-28-3).

CV-L

Coding violations line (near-end only).

ES-L

Errored seconds line.

SES-L

Severely errored seconds line (near-end only).

LOSS-L

Loss of signal seconds line (near-end only).

Line Threshold 1 Day

Port Number

The port number (1 to 14 for XTC-14; 1 to 28 for XTC-28-3).

CV-L

Coding violations line (near-end only).

ES-L

Errored seconds line.

SES-L

Severely errored seconds line (near-end only).

LOSS-L

Loss of signal seconds line (near-end only).

Electric Path Threshold 15 Minutes
Near End

Port Number

The port number (1 to 14 for XTC-14; 1 to 28 for XTC-28-3).

CV-P

Coding violations path information.

ES-P

Errored seconds path information.

SES-P

Severely errored seconds path information.

SAS-P

Severely errored frame/alarm indication signal-path information.

AISS-P

Alarm indication signal seconds path information.

UAS-P

Unavailable seconds path information.

Far End

Port Number

The port number (1 to 14 for XTC-14; 1 to 28 for XTC-28-3).

CV-P

Coding violations path information.

ES-P

Errored seconds path information.

SES-P

Severely errored seconds path information.

UAS-P

Unavailable seconds path information.

ESA-P

Errored seconds type A path information.

ESB-P

Errored seconds type B path information.

CSS-P

Controlled slip seconds path information.

SEFS-P

Severely errored framing seconds path information.

Electric Path Threshold 1 Day
Near End

Port Number

The port number (1 to 14 for XTC-14; 1 to 28 for XTC-28-3).

CV-P

Coding violations path information.

ES-P

Errored seconds path information.

SES-P

Severely errored seconds path information.

SAS-P

Severely errored frame/alarm indication signal path information.

AISS-P

Alarm indication signal seconds path information.

UAS-P

Unavailable seconds path information.

Far End

Port Number

The port number (1 to 14 for XTC-14; 1 to 28 for XTC-28-3).

CV-P

Coding violations path information.

ES-P

Errored seconds path information.

SES-P

Severely errored seconds path information.

UAS-P

Unavailable seconds path information.

ESA-P

Errored seconds type A path information.

ESB-P

Errored seconds type B path information.

CSS-P

Controlled slip seconds path information.

SEFS-P

Severely errored framing seconds path information.

Alarm Behavior

Displays alarm profile information.

Loopback

Line Number

The line number.

State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

Note The line state must be OOS_MT before you can configure the loopback type.

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or Facility (Line), or clear the current loopback (none).

Customer Info

STS Number

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.23.4  DS-3 Tab

The DS-3 tab allows you to view and update XTC DS-3 information.

Table C-143 Field Descriptions for the DS-3 Tab 

Field
Description
Line Config

Port Number

Displays the port number (1 to 3).

Port Name

Allows you to enter the name of the port. You can enter up to 32 alphanumeric or special characters. The port name is blank by default.

Line Length

Defines the distance (in feet) from backplane connection to the next termination point. Values are:

0 - 225 (default)

226 - 450

State

Displays the status of the line. Values are:

IS—In Service

IS_AINS—In Service-Auto In Service Soak

OOS—Out of Service

OOS_MT—Out of Service-Maintenance

AINS Soak

Automatic in-service soak. The amount of valid input signal in hh.mm, after which the port is set in service by the software. The range is from 0 to 48 hours, in 15-minute increments.

AINS Soak Count Down

Displays the remaining time of valid input signal in hh.mm, after which the card becomes IS automatically. The range is from 0 to 48 hours, in 15-minute increments.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

Line Threshold 15 Minutes

Port Number

The port number (1 to 3).

CV-L

Coding violations line.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

LOSS-L

Loss of signal seconds line.

Line Threshold 1 Day

Port Number

The port number (1 to 3).

CV-L

Coding violations line.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

LOSS-L

Loss of signal seconds line.

Alarm Behavior

Displays alarm profile information.

Loopback

Line Number

The line number.

State

Displays the status of the line. The line can be In Service (IS), In Service-Auto In Service Soak (IS_AINS), Out of Service (OOS), or Out of Service-Maintenance (OOS_MT).

Note The line state must be OOS_MT before you can configure the loopback type.

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or Facility (Line), or clear the current loopback (none).

Customer Info

STS Number

Displays the STS number.

Customer ID

The customer ID.

Service ID

The service ID.


C.1.23.5  STS-1 Path Tab

The STS-1 tab allows you to view and update XTC STS-1 path information.

Table C-144 Field Descriptions for the STS-1 Path Tab 

Field
Description
Threshold 15 Minutes

STS Number

The synchronous transport signal number.

CV-P

Coding violations path.

ES-P

Errored seconds path.

SES-P

Severely errored seconds path.

UAS-P

Unavailable seconds path.

FC-P

Failure count path.

PPJC-Pdet

Positive pointer justification count, STS path detected.

NPJC-Pdet

Negative pointer justification count, STS path detected.

PPJC-Pgen

Positive pointer justification count, STS path generated.

NPJC-Pgen

Negative pointer justification count, STS path generated.

PJCS-Pdet

Positive pointer justification count, STS path detected.

PJCS-Pgen

Positive pointer justification count, STS path generated.

PJC-Diff

The sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.

Threshold 1 Day

STS Number

The synchronous transport signal number.

CV-P

Coding violations path.

ES-P

Errored seconds path.

SES-P

Severely errored seconds path.

UAS-P

Unavailable seconds path.

FC-P

Failure count path.

PPJC-Pdet

Positive pointer justification count, STS path detected.

NPJC-Pdet

Negative pointer justification count, STS path detected.

PPJC-Pgen

Positive pointer justification count, STS path generated.

NPJC-Pgen

Negative pointer justification count, STS path generated.

PJCS-Pdet

Positive pointer justification count, STS path detected.

PJCS-Pgen

Positive pointer justification count, STS path generated.

PJC-Diff

The sum of the absolute values of differences between positive transmitted and received, and negative transmitted and received. The important metric on pointer justification is not the exact counts, but how many were absorbed.

Customer Info

STS Number

The STS number.

Customer ID

The user-defined customer ID number.

Service ID

The user-defined service ID number.


C.1.23.6  VT1.5 Path Tab

The VT1.5 Path tab allows you to view and update XTC VT1.5 path information.

Table C-145 Field Descriptions for the VT1.5 Path Tab 

Field
Description
Threshold 15 Minutes STS Term

STS Number

The synchronous transport signal number.

CV-P

Coding violations path.

ES-P

Errored seconds path.

SES-P

Severely errored seconds path.

UAS-P

Unavailable seconds path.

FC-P

Failure count path.

Threshold 1 Day STS Term

STS Number

The synchronous transport signal number.

CV-P

Coding violations path.

ES-P

Errored seconds path.

SES-P

Severely errored seconds path.

UAS-P

Unavailable seconds path.

FC-P

Failure count path.

Threshold 15 Minutes VT Term

VT Number

The virtual terminal number.

CV-V

Coding violations-VT path.

ES-V

Errored seconds-VT path.

SES-V

Severely errored seconds-VT path.

UAS-V

Unavailable seconds-VT path.

Threshold 1 Day VT Term

VT Number

The virtual terminal number.

CV-V

Coding violations-VT path.

ES-V

Errored seconds-VT path.

SES-V

Severely errored seconds-VT path.

UAS-V

Unavailable seconds-VT path.

Customer Info

VT Number

The virtual terminal number.

Customer ID

The user-defined customer ID number.

Service ID

The user-defined service ID number.


C.1.23.7  Alarm Extenders Tab

The Alarm Extenders tab allows you view XTC alarm information. The Alarm Extenders tab contains the following subtabs:

External Alarms Subtab

External Controls Subtab

C.1.23.7.1  External Alarms Subtab

The External Alarms subtab allows you to view and update external alarm information.

Table C-146 Field Descriptions for the External Alarms Subtab 

Field
Description

Input Number

The alarm input number.

Enabled

Check to activate the fields for the alarm input number.

Alarm Type

Choose an alarm type from the provided list.

Severity

Choose a severity from the list.

Raised When

Choose the contact condition that will trigger the alarm in CTC.

Virtual Wire

To assign the external device to a virtual wire, choose a virtual wire from the list, or choose None if no assignment is required.

Description

A default description is provided in this line for every external alarm that is enabled.

Raised

Indicates if an alarm has been raised.

Contact Status

Indicates the current status of the contact.


C.1.23.7.2  External Controls Subtab

The External Controls subtab allows you to view and update external controls.

Table C-147 Field Descriptions for the External Controls Subtab 

Field
Description

Control Number

The control number.

Enabled

Check to activate the fields for the control number.

Control Type

Choose a control type from the provided list.

Trigger Type

Choose a trigger type: a local minor, major, or critical alarm; a remote minor, major, or critical alarm; or a virtual wire activation.

Description

Enter a description.

Current State

The current state of the control.

Auto State

The auto state of the control.

Contact Setting

The current contact setting.


C.1.23.8  Protection Tab

The Protection tab allows you to view and update XTC protection group information.

Table C-148 Field Descriptions for the Protection Tab 

Field
Description

Protection Groups

Displays a list of available protection groups.

Protection Group Details

Displays details about the selected protection group.


C.1.23.9  J1 Path Trace Tab

The J1 Path Trace tab allows you to view and update J1 path trace information.

Table C-149 Field Descriptions for the J1 Path Trace Tab 

Field
Description

Port Number

Displays the port number.

STS Number

Displays the STS number.

Expected String

Displays the current expected string.

Received String

Displays the current received string.

Mode

Displays the path trace mode (Off/None, Auto, or Manual).

C2

Represents a machine-generated J1/J2 payload label byte.

Mismatch

Indicates whether there is a mismatch in the C2 byte received.

Vcat Member Number

Displays the virtual concatenation (VCAT) member number.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.1.24  Slot Properties—TNC

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Transport Node Controller (TNC) card combines the functions of multiple cards such as TCC2P, OSCM, ISC, and AIC-I. The TNC card supports the ONS 15454 M2 and ONS 15454 M6 shelf assemblies. The TNC card is provisioned as master and slave on the ONS 15454 M6 shelf, and as a standalone card on the ONS 15454 M2 shelf.

The following figure shows the TNC faceplate and block diagram.

Figure C-4 TNC Faceplate and Block Diagram

For the TNC module, the slot properties pane displays the following tabs: Module View, Identification, PPM, Alarm Behavior, UDC/VOIP, Optical Thresh, Auto Laser Shutdown, Line, and RMON Thresholds.

C.1.24.1  Module View Tab

The Module View tab displays a graphic of the TNC card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.24.2  Identification Tab

The Identification tab allows you to view and update TNC card identification information.

Table C-150 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Suppress Alarms

When checked, all alarms are suppressed for the port.


C.1.24.3  PPM Tab

The PPM tab allows you to view and provision the PPM and the ports inside the PPM.

Table C-151 Field Descriptions for the PPM Tab 

Field
Description
Pluggable Port Modules (PPM)

Pluggable Number

Displays the identifier of the plugin module.

Actual Equipment Type

Displays the actual card that is installed in the slot.

Equipment State

Displays the equipment state of the plugin module.

Administration State

Displays the port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

PPM

Port

Displays the port number for the PPM in the Pluggable Port Modules area.

Rate

Displays the port rate for the PPM in the Pluggable Port Modules area.


C.1.24.4  Alarm Behavior Tab

The Alarm Behavior tab allows you to view and update TNC card alarm profile information.

Table C-152 Field Descriptions for the Alarm Behavior Tab 

Field
Description

Port Number

Displays the card port number.

Alarm Profile

Displays the alarm profile that has been configured for the card. You can choose an alarm profile for the port from the drop-down list. Values are Default, Inherited, or a customized alarm profile.

Suppress Alarms

When checked, indicates that all alarms are suppressed for the card.

Alarm Profile

Choose an alarm profile for all ports.

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.1.24.5  UDC/VOIP

You can configure UDC/VoIP on a specific port. The TNC card supports the UDC/VoIP configuration only when Optical Supervisory Channel (OSC) is configured on the ports. From the Service Type drop-down list, choose UDC or VOIP.

C.1.24.6  Optical Thresh

The Optical Thresh tab allows you to view and provision optical threshold settings. The tab contains the following subtabs:

TCA 15 Min Subtab

TCA 1 Day Subtab

Alarm Thresh Subtab

C.1.24.6.1  TCA 15 Min Subtab

The TCA 15 Min subtab allows you to set thresholds for 15-minute threshold crossing alert generation.

Table C-153 Field Descriptions for the TCA 15 Min Subtab 

Field
Description

Port Number

Displays the port number.

LBC-High

Displays the maximum threshold for the laser bias current.

OPR-High

Displays the maximum threshold for the optical power received.

OPR-Low

Displays the minimum threshold for the optical power received.

OPT-High

Displays the maximum threshold for the optical power transmitted.

OPT-Low

Displays the minimum threshold for the optical power transmitted.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.6.2  TCA 1 Day Subtab

The TCA 1 Day subtab allows you to set thresholds for 1-day threshold crossing alert generation.

Table C-154 Field Descriptions for the TCA 1 Day Subtab 

Field
Description

Port Number

Displays the port number.

LBC-High

Displays the maximum threshold for the laser bias current.

OPR-High

Displays the maximum threshold for the optical power received.

OPR-Low

Displays the minimum threshold for the optical power received.

OPT-High

Displays the maximum threshold for the optical power transmitted.

OPT-Low

Displays the minimum threshold for the optical power transmitted.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.6.3  Alarm Thresh Subtab

The Alarm Thresh subtab allows you to select thresholds for alarm generation.

Table C-155 Field Descriptions for the Alarm Thresh Subtab 

Field
Description

Port Number

Displays the port number.

LBC-High

Displays the maximum threshold for the laser bias current.

OPR-High

Displays the maximum threshold for the optical power received.

OPR-Low

Displays the minimum threshold for the optical power received.

OPT-High

Displays the maximum threshold for the optical power transmitted.

OPT-Low

Displays the minimum threshold for the optical power transmitted.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.7  Auto Laser Shutdown Tab

The Auto Laser Shutdown tab allows you to view and update the automatic laser shutdown parameters.

Table C-156 Field Descriptions for the Auto Laser Shutdown Tab 

Field
Description
OC3 Line

Port Number

Displays the port number.

OSRI

Displays the OSRI. Values are:

On—Laser switch is locked on

Off—(Cisco default) There is no lock on the lasers

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.

FE Line

Port Number

Displays the port number.

OSRI

Displays the OSRI. Values are:

On—Laser switch is locked on

Off—(Cisco default) There is no lock on the lasers

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.

ONE GE Line

Port Number

Displays the port number.

OSRI

Displays the OSRI. Values are:

On—Laser switch is locked on

Off—(Cisco default) There is no lock on the lasers

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.


C.1.24.8  Line Tab

The Line tab allows you to configure line information. The tab contains the following subtabs:

Ports Subtab

OC3 Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

C.1.24.8.1  Ports Subtab

The ports subtab allows you to provision PPM parameters of a TNC card.

Table C-157 Field Descriptions for the Ports Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a port name.

Administration State

The port administration state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)


C.1.24.8.2  OC3 Subtab

The OC3 subtab allows you to view and change the OC3 line settings on the TNC card.

Table C-158 Field Descriptions for the OC3 Subtab

Field
Description

Port Number

Displays the card port number.

Port Name

Displays the port name.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

ProvidesSync

When checked, the card is provisioned as an NE timing reference.

EnableSyncMsg

Enables synchronization status messages (S1 byte), which allow the node to choose the best timing source.

PJSTSMon#

Sets the STS that will be used for pointer justification. If set to 0, no STS is monitored. Only one STS can be monitored on each OC-N port.

0 (default)-3 (OC-3, per port)

0 (default)-12 (OC-12)

0 (default)-48 (OC-48)

SendDoNotUse

When checked, sends a do not use (DUS) message on the S1 byte.


C.1.24.8.3  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change 15-minute near- and far-end line thresholds for the TNC card.

Table C-159 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-L

Displays the coding violations line.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

FC-L

Displays the failure count line.

UAS-L

Displays the unavailable seconds line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port Number

Displays the port number.

CV-L

Displays the coding violations line.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

FC-L

Displays the failure count line.

UAS-L

Displays the unavailable seconds line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.8.4  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change 1-day near- and far-end line thresholds for the TNC card.

Table C-160 Field Descriptions for the Line Thresh 1 Day Subtab

Field
Description
Near End

Port Number

Displays the port number.

CV-L

Displays the coding violations line.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

FC-L

Displays the failure count line.

UAS-L

Displays the unavailable seconds line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port Number

Displays the port number.

CV-L

Displays the coding violations line.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

FC-L

Displays the failure count line.

UAS-L

Displays the unavailable seconds line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.8.5  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change 15-minute near-end section thresholds for the TNC card.

Table C-161 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.8.6  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change 1-day near-end regenerator section thresholds for the TNC card.

Table C-162 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.1.24.9  RMON Thresholds

The RMON Thresholds tab allows you to view RMON thresholds for the TNC card. These thresholds are applicable to Fast Ethernet and Gigabit Ethernet Pluggable rates.

Table C-163 Field Descriptions for the RMON Thresholds Tab 

Field
Description

Index Number

Displays the optical port number.

Slot

Displays the slot.

Port

Displays the port.

Variable

Displays the Ethernet threshold variable. The variable depends on the card type.

Alarm Type

Displays the Ethernet threshold alarm type. Values are Rising, Falling, or Rising and Falling.

Sample Type

Displays the Ethernet threshold sample type. Values are Relative and Absolute. Relative restricts the threshold to using the number of occurrences in the user-set sample period. Absolute sets the threshold to use the total number of occurrences, regardless of any time period.

Sample Period (sec)

Displays the Ethernet threshold sample period, in seconds.

Rising Thresholds (count)

Displays a count of the number of times an alarm entry crosses the rising threshold and the entry generates an event.

Falling Thresholds (count)

Displays a count of the number of times an alarm entry crosses the falling threshold and the entry generates an event.


C.1.25  Slot Properties—TSC (ONS 15454 SONET and ONS 15454 SDH)

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Transport Shelf Controller (TSC) card combines the functions of multiple cards such as TCC2P, ISC, and AIC-I. The TSC card supports the ONS 15454 M2 and ONS 15454 M6 shelf assemblies. The card has a similar look and feel to TCC2/TCC2P/TCC3 cards. The TSC card is provisioned as master and slave on the ONS 15454 M6 shelf, and as a standalone card on the ONS 15454 M2 shelf. The TSC card serves as the processor card for the node.

The following figure shows the TSC faceplate and block diagram.

Figure C-5 TSC Faceplate and Block Diagram

For the TSC module, the slot properties pane displays the following tabs: Module View and Identification.

C.1.25.1  Module View Tab

The Module View tab displays a graphic of the TSC card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.25.2  Identification Tab

The Identification tab allows you to view and update TSC card identification information.

Table C-164 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Suppress Alarms

When checked, all alarms are suppressed for the port.


C.1.26  Slot Properties—TCC3

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The Timing Communications Control Three (TCC3) card is an enhanced version of the TCC2P card. The primary enhancements include the increase in memory size and compact flash space. The TCC3 card boots up as a TCC2P card in older releases and as a TCC3 card from Release 9.2 onwards. The TCC3 card supports multi-shelf management. The TCC3 card acts as a shelf controller and node controller for the ONS 15454.

The following figure shows the TCC3 faceplate and block diagram.

Figure C-6 TCC3 Faceplate and Block Diagram

For the TCC3 module, the slot properties pane displays the following tabs: Module View, Identification, and Info.

C.1.26.1  Module View Tab

The Module View tab displays a graphic of the TCC3 card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.1.26.2  Identification Tab

The Identification tab allows you to view and update TCC3 card identification information.

Table C-165 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Suppress Alarms

When checked, all alarms are suppressed for the port.


C.1.26.3  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the TCC3 card.

Table C-166 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.2  DWDM Cards

This section describes the following DWDM cards supported within CTM:

Slot Properties—2.5G_DM

Slot Properties—2.5G_DMP

Slot Properties—2.5G Multirate Transponder

Slot Properties—32DMX

Slot Properties—32DMX-L

Slot Properties—32DMX_O

Slot Properties—40-DMX-C

Slot Properties—32MUX_O

Slot Properties—40-MUX-C

Slot Properties—32WSS

Slot Properties—32WSS-L

Slot Properties—40-WSS-C

Slot Properties—40-WXC-C

Slot Properties—80-WXC-C

Slot Properties—40G-MXP-C

Slot Properties—4MD_xx.x

Slot Properties—AD_1B_xx.x

Slot Properties—AD_1C_xx.x

Slot Properties—AD_2C_xx.x

Slot Properties—AD_4B_xx.x

Slot Properties—AD_4C_xx.x

Slot Properties—ADM-10G

Slot Properties—GE_XP and 10GE_XP

Slot Properties—MXP_2.5G_10E

Slot Properties—MXP_2.5G_10G

Slot Properties—MXP_MR_10DME

Slot Properties—OPT-AMP-17-C and OPT-AMP-C

Slot Properties—OPT-AMP-L

Slot Properties—OPT-RAMP-C and OPT-RAMP-CE

Slot Properties—OPT-BST

Slot Properties—OPT-BST-E

Slot Properties—OPT-BST-L

Slot Properties—OPT-PRE

Slot Properties—OSC-CSM

Slot Properties—OTU2_XP

Slot Properties—PSM

Slot Properties—SMR-C

Slot Properties—T-DCU (TDC-CC and TDC-FC)

Slot Properties—TXP_MR_10E

Slot Properties—TXP_MR_10E_C

Slot Properties—TXP_MR_10G

C.2.1  Slot Properties—2.5G_DM

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The 2.5G-DM card is capable of translating client input GE, ESCON, FICON, 1G and 2G Fiber Channel, and IBM GDPS optical signal into an optical signal with an optical frequency on the 100-GHz spacing frequency grid according to ITU-T G.692. The datamux cards are GR-253 and G.957 compliant. This card supports 8 client interfaces utilizing SFP technology, and 32 ITU wavelengths are supported. Each card supports tunability over 4 wavelengths. The card is supported on ONS 15454 SONET and ONS 15454 SDH platforms.

The following figure shows the card faceplate.

Figure C-7 2.5G-DM Module

For the 2.5G_DM module, the slot properties pane displays the following tabs: Module View, Identification, Card, PPM, Line, Loopback, Auto Laser Shutdown, Optical Thresh, Alarm Behavior, Protection, and Info.


Note The tabs shown depend on the NE configuration.


C.2.1.1  Module View Tab

The Module View tab displays a graphic of the 2.5G_DM that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.2.1.2  Identification Tab

The Identification tab allows you to view and update 2.5G_DM identification information.

Table C-167 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Suppress Alarms

When checked, all alarms are suppressed for the port.


C.2.1.3  Card Tab

The Card tab allows you to view and update card information.

Table C-168 Field Descriptions for the Card Tab 

Field
Description

Card Mode

Allows you to select a card mode. Select from:

FC_GE—Allows you to select a multicard Ether Switch group, a single-card Ether Switch group, or the Port Mapped mode for E-series cards.

Mixed—Supports 1G FC or GE traffic on port 1, and ESCON traffic on ports 5 through 8.

ESCON—Supports 8 ports of ESCON traffic.


C.2.1.4  PPM Tab

The PPM tab allows you to view and provision the PPM and the ports inside the PPM.

Table C-169 Field Descriptions for the PPM Tab 

Field
Description
Pluggable Port Modules (PPM)

Pluggable Number

Displays the identifier of the plugin module.

Equipment Type

Displays the equipment type that the slot is provisioned for.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Actual Equipment Type

Displays the actual card that is installed in the slot. Values are single mode or multimode.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

User Code

Allows you to enter an ASCII string to identify the card. The user code is stored in nonvolatile memory so that it is not lost when the unit is moved or stored as a spare.

Product ID

Displays a plugin module ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

Displays the port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the plugin module.

Alarm Profile

Sets the alarm profile for the card.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this plugin module and its port(s).

PPM

Pluggable Number

Displays the identifier of the plugin module.

Equipment Type

Displays the plugin type that the port is provisioned for.


C.2.1.4.1  Provision Pluggable Dialog Box

Click the Create button to launch the Provision Pluggable dialog box. This dialog box allows you to provision the PPM and to create the ports inside this entity. See Provision Pluggable Dialog Box for more information.

C.2.1.5  Line Tab

The Line tab allows you to configure line information. If the card is installed on an ONS 15454 SONET NE, the tab contains the following subtabs:

Section Trace Subtab

SONET Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Wavelength Trunk Settings Subtab

Client Subtab

RMON Thresholds Subtab

Distance Extension Subtab

Enhanced FC/FICON ISL Subtab


Note If the card is installed on an ONS 15454 SDH NE, see the SDH Line section. The following information is the same if the payload is SDH on an ONS 15454 SONET NE.


C.2.1.5.1  Section Trace Subtab

The Section Trace subtab allows you to change the section trace settings for the 2.5G-DM card.

Table C-170 Field Descriptions for the Section Trace Subtab 

Field
Description

Port Number

Displays the port number.

Trace Mode

The trace mode (Off/None or Manual).

Disable AIS/RDI on TIM-S

Allows you to disable the Alarm Indication Signal (AIS) and the Remote Defect Indication (RDI) when the path Trace Identifier Mismatch Section (TIM-S) alarm is detected.

Transmit Length

Select a transmit length for the trace.

Current Transmit String

Displays the current transmit string. The trail trace identifier is 64 bytes in length.

Current Expected String

Displays the current expected string; sets a new expected string.

Current Received String

Displays the current received string.


C.2.1.5.2  SONET Subtab

The SONET subtab allows you to view and change the SONET line settings for the 2.5G-DM module.

Table C-171 Field Descriptions for the SONET Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a name for the optical port.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Type

Defines the port.

ProvidesSync

When checked, the card is provisioned as an NE timing reference.

EnableSyncMsg

Enables synchronization status messages (S1 byte), which allow the node to choose the best timing source.

SendDoNotUse

When checked, sends a do not use (DUS) message on the S1 byte.

Admin SSM

Overrides the synchronization status message (SSM) synchronization traceability unknown (STU) value. If the node does not receive an SSM signal, it defaults to STU.


C.2.1.5.3  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change 15-minute near-end section thresholds for the 2.5G_DM module.

Table C-172 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.5.4  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change 1-day near-end regenerator section thresholds for the 2.5G_DM module.

Table C-173 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.5.5  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change 15-minute near- and far-end line thresholds for the 2.5G_DM module.

Table C-174 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port No.

The port number.

CV-L

Coding violations line.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port No.

The port number.

CV-L

Coding violations line.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.5.6  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change 1-day near- and far-end line thresholds for the 2.5G_DM module.

Table C-175 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port No.

The port number.

CV-L

Coding violations line.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port No.

The port number.

CV-L

Coding violations line.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.5.7  Wavelength Trunk Settings Subtab

The Wavelength Trunk Settings subtab allows you to change the wavelength and band settings for the 2.5G_DM card.

Table C-176 Field Descriptions for the Wavelength Trunk Settings Subtab 

Field
Description

Port Number

Displays the optical port number.

Port Name

Allows you to enter an optical port name.

Wavelength

Allows you to provision the wavelength frequency. The Wavelength column lists the correct wavelengths, depending on the type of card and the band selected. Refer to the Other Information field in the Equipment Inventory table (11.3.1.3  Equipment Inventory Table for CTC-Based NEs, page 11-11) for details of wavelengths supported.

Band

The Band column reduces the number of selectable wavelengths (82/80 lambdas only). For this single-band card, the band value is fixed to C, and this value cannot be altered.


C.2.1.5.8  Client Subtab

The Client subtab allows you to provision PPM parameters for the 2.5G_DM card.

Table C-177 Field Descriptions for the Client Subtab 

Field
Description

Port Number

Displays the optical port number.

Port Name

Allows you enter a port name.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

AINS Soak (H:M)

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency.


C.2.1.5.9  RMON Thresholds Subtab

The RMON Thresholds tab allows you to view RMON thresholds for the 2.5G_DM module.

Table C-178 Field Descriptions for the RMON Thresholds Subtab 

Field
Description

Show all RMON Thresholds

When checked, shows all RMON thresholds.

Index Number

Displays the optical port number.

Slot

Displays the slot.

Port

Displays the port.

Variable

Displays the Ethernet threshold variable. The variable depends on the card type.

Alarm Type

Displays the Ethernet threshold alarm type. Values are Rising, Falling, or Rising and Falling.

Sample Type

Displays the Ethernet threshold sample type. Values are Relative and Absolute. Relative restricts the threshold to using the number of occurrences in the user-set sample period. Absolute sets the threshold to use the total number of occurrences, regardless of any time period.

Sample Period (sec)

Displays the Ethernet threshold sample period, in seconds.

Rising Thresh

Displays a count of the number of times an alarm entry crosses the rising threshold and the entry generates an event.

Falling Thresh

Displays a count of the number of times an alarm entry crosses the falling threshold and the entry generates an event.


C.2.1.5.10  Distance Extension Subtab

The Distance Extension subtab allows you to enable the buffer-to-buffer extension between the client and the 2.5G_DM card in order to increase the DWDM distance without affecting the throughput.

Table C-179 Field Descriptions for the Distance Extension Subtab 

Field
Description

Port Number

Displays the port number.

Client interface: 1 to 8

Trunk: 9

Enable Distance Extension

Allows end-to-end distances of up to 1600 km for 1 GFC and up to 800 km for 2 GFC.

Auto Detect Credits

Allows automatic detection of buffer credits for flow control.

Credits Available

Displays the number of credits available.

Autoadjust GFP Buffer Threshold

Allows the threshold of the generic framing procedure (GFP) buffer between two 2.5G_DM cards. This is automatically adjusted.

GFP Buffers Available

Displays the number of GFP buffers available between two 2.5G_DM cards.


C.2.1.5.11  Enhanced FC/FICON ISL Subtab

The Enhanced FC/FICON ISL subtab allows you to enable the field programmable gate array (FPGA) to drop duplicate frames.

Table C-180 Field Descriptions for the Enhanced FC/FICON ISL Subtab 

Field
Description

Port Number

Displays the port number.

Maximum Frame Size

Allows you to select the maximum frame size supported by the FICON/FC. Valid range is from 2148 to 2172.


C.2.1.6  Loopback Tab

The Loopback tab allows you to view and update 2.5G_DM loopback information.

Table C-181 Field Descriptions for the Loopback Tab 

Field
Description

Port Number

Displays the port number.

Port Name

Displays the name of the port.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or clear the current loopback (none).

Note The line state must be OOS_MT before you can configure the loopback type.


C.2.1.7  Auto Laser Shutdown Tab

The Auto Laser Shutdown tab allows you to view and update the automatic laser shutdown parameters.

Table C-182 Field Descriptions for the Auto Laser Shutdown Tab 

Field
Description

Port Number

Displays the port number.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.


C.2.1.8  Optical Thresh Tab

The Optical Thresh tab allows you to view and provision optical threshold settings. The tab contains the following subtabs:

TCA 15 Min Subtab

TCA 1 Day Subtab

Alarm Thresh Subtab

C.2.1.8.1  TCA 15 Min Subtab

The TCA 15 Min subtab allows you to set thresholds for 15-minute threshold crossing alert generation.

Table C-183 Field Descriptions for the TCA 15 Min Subtab 

Field
Description

Port Number

Displays the port number.

Laser Bias High (%)

Displays the upper laser bias threshold.

Rx Power High (dBm)

Displays the upper receive power threshold.

Rx Power Low (dBm)

Displays the lower receive power threshold.

Tx Power High (dBm)

Displays the upper transmit power threshold.

Tx Power Low (dBm)

Displays the lower transmit power threshold.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.8.2  TCA 1 Day Subtab

The TCA 1 Day subtab allows you to set thresholds for 1-day threshold crossing alert generation.

Table C-184 Field Descriptions for the TCA 1 Day Subtab 

Field
Description

Port Number

Displays the port number.

Laser Bias High (%)

Displays the upper laser bias threshold.

Rx Power High (dBm)

Displays the upper receive power threshold.

Rx Power Low (dBm)

Displays the lower receive power threshold.

Tx Power High (dBm)

Displays the upper transmit power threshold.

Tx Power Low (dBm)

Displays the lower transmit power threshold.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.8.3  Alarm Thresh Subtab

The Alarm Thresh subtab allows you to select thresholds for alarm generation.

Table C-185 Field Descriptions for the Alarm Thresh Subtab 

Field
Description

Port Number

Displays the port number.

Laser Bias High (%)

Displays the upper laser bias threshold.

Rx Power High (dBm)

Displays the upper receive power threshold.

Rx Power Low (dBm)

Displays the lower receive power threshold.

Tx Power High (dBm)

Displays the upper transmit power threshold.

Tx Power Low (dBm)

Displays the lower transmit power threshold.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.1.9  Alarm Behavior Tab

The Alarm Behavior tab allows you to view and update 2.5G_DM alarm profile information.

Table C-186 Field Descriptions for the Alarm Behavior Tab 

Field
Description

Alarm Profile

Displays the alarm profile that has been configured for the card.

Suppress Alarms

When checked, indicates that all alarms are suppressed for the card.

Port Number

Displays the card port number.

Alarm Profile

Choose an alarm profile for the port from the drop-down list. Values are Default, Inherited, or a customized alarm profile.

Suppress Alarms

When checked, all alarms are suppressed for the port.

Alarm Profile

Choose an alarm profile for all ports.

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.2.1.10  Protection Tab

The Protection tab allows you to view and update 2.5G_DM protection group information.

Table C-187 Field Descriptions for the Protection Tab 

Field
Description

Protection Groups

Displays a list of available protection groups.

Protection Group Details

Displays details about the selected protection groups and allows you to execute switch commands.


C.2.1.11  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the 2.5G_DM card.

Table C-188 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.

Units

Displays the unit of measure (when applicable) of the object that is inventoried.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.2.2  Slot Properties—2.5G_DMP

The slot properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The 2.5G-DMP card is capable of translating client input GE, ESCON, FICON, 1G and 2G Fiber Channel, and IBM GDPS optical signal into an optical signal with an optical frequency on the 100 GHz spacing frequency grid according to ITU-T G.692. The datamux cards are GR-253 and G.957 compliant. This card supports eight client interfaces utilizing SFP technology and protection on the trunk side. 32 ITU wavelengths are supported. Each card supports tunability over four wavelengths. This card is supported on ONS 15454 SONET and ONS 15454 SDH platforms.

The following figure shows the card faceplate.

Figure C-8 2.5G-DMP Module

For the 2.5G_DMP module, the slot properties pane displays the following tabs: Module View, Identification, Card, PPM, Line, Loopback, Auto Laser Shutdown, Optical Thresh, Alarm Behavior, Protection, and Info.


Note Tabs shown depend on whether the NE is a SONET or an SDH node.


C.2.2.1  Module View Tab

The Module View tab displays a graphic of the 2.5G_DMP that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.2.2.2  Identification Tab

The Identification tab allows you to view and update 2.5G_DMP identification information.

Table C-189 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).

Suppress Alarms

When checked, all alarms are suppressed for the port.


C.2.2.3  Card Tab

The Card tab allows you to view and update card information.

Table C-190 Field Descriptions for the Card Tab 

Field
Description

Card Mode

Allows you to select a card mode. Select from:

FC_GE—Allows you to select a multicard Ether Switch group, a single-card Ether Switch group, or the Port Mapped mode for E-series cards.

Mixed—Supports 1G FC or GE traffic on port 1, and ESCON traffic on ports 5 through 8.

ESCON—Supports 8 ports of ESCON traffic.


C.2.2.4  PPM Tab

The PPM tab allows you to view and provision the PPM and the ports inside the PPM.

Table C-191 Field Descriptions for the PPM Tab 

Field
Description
Pluggable Port Modules (PPM)

Pluggable Number

Displays the identifier of the plugin module.

Equipment Type

Displays the equipment type that the slot is provisioned for.

Hardware Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware revision number.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Actual Equipment Type

Displays the actual card that is installed in the slot. Values are single mode or multimode.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

User Code

Allows you to enter an ASCII string to identify the card. The user code is stored in nonvolatile memory so that it is not lost when the unit is moved or stored as a spare.

Product ID

Displays a plugin module ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Administration State

Displays the port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the plugin module.

Alarm Profile

Sets the alarm profile for the card.

Suppress Alarms

Check the Suppress Alarms check box to suppress all alarms for this plugin module and its port(s).

PPM

Pluggable Number

Displays the identifier of the plugin module.

Equipment Type

Displays the plugin type that the port is provisioned for.


C.2.2.4.1  Provision Pluggable Dialog Box

Click the Create button to launch the Provision Pluggable dialog box. This dialog box allows you to provision the PPM and to create the ports inside this entity. See Provision Pluggable Dialog Box for more information.

C.2.2.5  Line Tab

The Line tab allows you to configure line information. If the card is installed on an ONS 15454 SONET NE, the tab contains the following subtabs:

Section Trace Subtab

SONET Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Wavelength Trunk Settings Subtab

Client Subtab

RMON Thresholds Subtab

Distance Extension Subtab

Enhanced FC/FICON ISL Subtab


Note If the card is installed on an ONS 15454 SDH NE, see the SDH Line section. The following information is the same if the payload is SDH on an ONS 15454 SONET NE.


C.2.2.5.1  Section Trace Subtab

The Section Trace subtab allows you to change the section trace settings for the 2.5G_DMP card.

Table C-192 Field Descriptions for the Section Trace Subtab 

Field
Description

Port Number

Displays the port number.

Trace Mode

The trace mode (Off/None or Manual).

Disable AIS/RDI on TIM-S

Allows you to disable the Alarm Indication Signal (AIS) and the Remote Defect Indication (RDI) when the path Trace Identifier Mismatch Section (TIM-S) alarm is detected.

Transmit Length

Select a transmit length for the trace.

Current Transmit String

Displays the current transmit string. The trail trace identifier is 64 bytes in length.

Current Expected String

Displays the current expected string; sets a new expected string.

Current Received String

Displays the current received string.


C.2.2.5.2  SONET Subtab

The SONET subtab allows you to view and change the SONET line settings for the 2.5G-DMP module.

Table C-193 Field Descriptions for the SONET Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a name for the optical port.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

SF BER

Sets the signal fail bit error rate.

SD BER

Sets the signal degrade bit error rate.

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).


C.2.2.5.3  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change the 15-minute near-end section thresholds of the 2.5G_DMP card.

Table C-194 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays Errored seconds section.

SES-S

Displays Severely errored seconds section.

SEFS-S

Displays Severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.5.4  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change the 1-day near-end section thresholds of the 2.5G_DMP card.

Table C-195 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description
Near End

Port Number

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.5.5  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the 15-minute near- and far-end line thresholds of the 2.5G_DMP card.

Table C-196 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port No.

The port number.

ES-L

Errored seconds line

SES-L

Severely errored seconds line.

CV-L

Coding violations line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port No.

The port number.

ES-L

Errored seconds line

SES-L

Severely errored seconds line.

CV-L

Coding violations line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.5.6  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the 1-day near- and far-end line thresholds of the 2.5G_DMP card.

Table C-197 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port No.

The port number.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

CV-L

Coding violations line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port No.

The port number.

ES-L

Errored seconds line.

SES-L

Severely errored seconds line.

CV-L

Coding violations line.

UAS-L

Unavailable seconds line.

FC-L

Failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.5.7  Wavelength Trunk Settings Subtab

The Wavelength Trunk Settings subtab allows you to change the wavelength and band settings for the 2.5G_DMP card.

Table C-198 Field Descriptions for the Wavelength Trunk Settings Subtab 

Field
Description

Port Number

Displays the optical port number.

Port Name

Allows you to enter an optical port name.

Wavelength

Allows you to provision the wavelength frequency. The Wavelength column lists the correct wavelengths, depending on the type of card and the band selected. Refer to the Other Information field in the Equipment Inventory table for details of wavelengths supported. See 11.3.1.3  Equipment Inventory Table for CTC-Based NEs, page 11-11.

Band

The Band column reduces the number of selectable wavelengths (82/80 lambdas only). For this single-band card, the band value is fixed to C, and this value cannot be altered.


C.2.2.5.8  Client Subtab

The Client subtab allows you to provision PPM parameters for the 2.5G_DMP card.

Table C-199 Field Descriptions for the Client Subtab 

Field
Description

Port Number

Displays the optical port number.

Port Name

Allows you to enter a port name.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

AINS Soak (H:M)

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency.


C.2.2.5.9  RMON Thresholds Subtab

The RMON Thresholds subtab allows you to view, create, and delete RMON threshold settings for the 2.5G_DMP card.

Table C-200 Field Descriptions for the RMON Thresholds Subtab 

Field
Description

Index Number

Displays the optical port number.

Slot

Displays the slot.

Port

Displays the port.

Variable

Displays the Ethernet threshold variable. The variable depends on the card type.

Alarm Type

Displays the Ethernet threshold alarm type. Values are Rising, Falling, or Rising and Falling.

Sample Type

Displays the Ethernet threshold sample type. Values are Relative and Absolute. Relative restricts the threshold to using the number of occurrences in the user-set sample period. Absolute sets the threshold to use the total number of occurrences, regardless of any time period.

Sample Period (sec)

Displays the Ethernet threshold sample period, in seconds.

Rising Thresholds

Displays a count of the number of times an alarm entry crosses the rising threshold and the entry generates an event.

Falling Thresholds

Displays a count of the number of times an alarm entry crosses the falling threshold and the entry generates an event.

Create

Click the Create button to create an RMON threshold.

Delete

Select an RMON threshold from the list displayed and click the Delete button.


C.2.2.5.10  Distance Extension Subtab

The Distance Extension subtab allows you to enable the buffer-to-buffer extension between the client and the 2.5G_DMP card in order to increase the DWDM distance without affecting the throughput.

Table C-201 Field Descriptions for the Distance Extension Subtab 

Field
Description

Port Number

Displays the port number.

Client Interface: 1 to 8

Trunk: 9 to 10

Enable Distance Extension

Allows end-to-end distances of up to 1600 km for 1 GFC and up to 800 km for 2 GFC.

Auto Detect Credits

Allows automatic detection of buffer credits for flow control.

Credits Available

Displays the number of credits available.

Autoadjust GFP Buffer Threshold

Allows the threshold of the GFP buffer between two 2.5G_DMP cards. This is automatically adjusted.

GFP Buffers Available

Displays the number of GFP buffers available between two 2.5G_DMP cards.


C.2.2.5.11  Enhanced FC/FICON ISL Subtab

The Enhanced FC/RCON ISL subtab allows you to enable the FCGA to drop duplicate frames.

Table C-202 Field Descriptions for the Enhanced FC/FICON ISL Subtab 

Field
Description

Port Number

Displays the port number.

Maximum Frame Size

Allows you to select the maximum frame size supported by the FICON/FC. Valid range is from 2148 to 2172.


C.2.2.6  Loopback Tab

The Loopback tab allows you to view and update 2.5G_DMP loopback information.

Table C-203 Field Descriptions for the Loopback Tab 

Field
Description

Port Number

Displays the port number.

Port Name

Displays the name of the port.

Administration State

The port administration state. It can be:

IS—In Service

IS, AINS—Automatic In Service

OOS, DSBLD—Out of Service, Disabled

OOS, MT—Out of Service, Maintenance

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Loopback Type

Allows you to configure a port to terminal loopback (Inward) or clear the current loopback (none).

Note The line state must be OOS_MT before you can configure the loopback type.


C.2.2.7  Auto Laser Shutdown Tab

The Auto Laser Shutdown tab allows you to view and update the automatic laser shutdown parameters.

Table C-204 Field Descriptions for the Auto Laser Shutdown Tab 

Field
Description

Port Number

Displays the port number.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

Rec. Pulse Dur. (sec)

Allows you to set the received laser pulse duration, in seconds. The range is from 2.0 to 100.0 seconds.

Rec. Pulse Int. (sec)

Allows you to set the received laser pulse interval, in seconds. The range is from 60 to 300 seconds.

Status

Displays the current laser status. Values are Shut Down or Not Shut Down.

Request Restart

When selected, allows you to request a laser restart. This parameter is configurable only when the ALS mode is set to Manual Restart or Manual Restart for Test and when the laser status is Shutdown.


C.2.2.8  Optical Thresh Tab

The Optical Thresh tab allows you to view and provision optical threshold settings. The tab contains the following subtabs:

TCA 15 Min Subtab

TCA 1 Day Subtab

Alarm Thresh Subtab

C.2.2.8.1  TCA 15 Min Subtab

The TCA 15 Min subtab allows you to set thresholds for 15-minute threshold crossing alert generation.

Table C-205 Field Descriptions for the TCA 15 Min Subtab 

Field
Description

Port Number

Displays the port number.

Laser Bias High (%)

Displays the upper laser bias threshold.

Rx Power High (dBm)

Displays the upper receive power threshold.

Rx Power Low (dBm)

Displays the lower receive power threshold.

Tx Power High (dBm)

Displays the upper transmit power threshold.

Tx Power Low (dBm)

Displays the lower transmit power threshold.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.8.2  TCA 1 Day Subtab

The TCA 1 Day subtab allows you to set thresholds for 1-day threshold crossing alert generation.

Table C-206 Field Descriptions for the TCA 1 Day Subtab 

Field
Description

Port Number

Displays the port number.

Laser Bias High (%)

Displays the upper laser bias threshold.

Rx Power High (dBm)

Displays the upper receive power threshold.

Rx Power Low (dBm)

Displays the lower receive power threshold.

Tx Power High (dBm)

Displays the upper transmit power threshold.

Tx Power Low (dBm)

Displays the lower transmit power threshold.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.8.3  Alarm Thresh Subtab

The Alarm Thresh subtab allows you to select thresholds for alarm generation.

Table C-207 Field Descriptions for the Alarm Thresh Subtab 

Field
Description

Port Number

Displays the port number.

Laser Bias High (%)

Displays the upper laser bias threshold.

Rx Power High (dBm)

Displays the upper receive power threshold.

Rx Power Low (dBm)

Displays the lower receive power threshold.

Tx Power High (dBm)

Displays the upper transmit power threshold.

Tx Power Low (dBm)

Displays the lower transmit power threshold.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.2.9  Alarm Behavior Tab

The Alarm Behavior tab allows you to view and update 2.5G_DMP alarm profile information.

Table C-208 Field Descriptions for the Alarm Behavior Tab 

Field
Description

Alarm Profile

Displays the alarm profile that has been configured for the card.

Suppress Alarms

When checked, indicates that all alarms are suppressed for the card.

Port Number

Displays the card port number.

Alarm Profile

Choose an alarm profile for the port from the drop-down list. Values are Default, Inherited, or a customized alarm profile.

Suppress Alarms

When checked, all alarms are suppressed for the port.

Alarm Profile

Choose an alarm profile for all ports.

Force to All Ports

When clicked, forces all the ports to the selected alarm profile.


C.2.2.10  Protection Tab

The Protection tab allows you to view and update 2.5G_DMP protection group information.

Table C-209 Field Descriptions for the Protection Tab 

Field
Description

Protection Groups

Displays a list of available protection groups.

Protection Group Details

Displays details about the selected protection groups and allows you to execute switch commands.


C.2.2.11  Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the 2.5G_DMP card.

Table C-210 Field Descriptions for the Info Tab 

Field
Description

Attribute

Displays the nominal card specification.

Value

Displays the value of the attribute.

Units

Displays the unit of measure (when applicable) of the object that is inventoried.



Note See Table 1-23 on page 1-49 for descriptions of actions that you can perform using the buttons at the bottom of the window.


C.2.3  Slot Properties—2.5G Multirate Transponder

The slot properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the card properties.

The 2.5-Gb/s multirate transponder cards operate on the ITU grid and provide the ONS 15454 SONET and ONS 15454 SDH with enhanced economics in metro DWDM solutions. The multirate transponder cards provide a 2R/3R transponder functionality over a bit rate of 100 Mb/s to 2.5 Gb/s. The cards also provide a single-mode fiber DWDM interface. Multirate transponder cards use pluggable small form factor client interfaces. The cards translate the client input optical signal into an optical signal with an optical frequency on the spacing frequency grid according to ITU-T G.692. The cards are GR-253 and G.957 compliant.

There are two versions of the multirate 2.5G transponder card:

Multirate 2.5G transponder, nonfiber-protected (TXP_MR_2.5G_xx.x)

Multirate 2.5G transponder, fiber-protected (TXPP_MR_2.5G_xx.x)

CTM supports DVB-ASI and ISC1 payloads on TXP_MR_2.5G and TXPP _MR_2.5G cards. Using these payloads, you can:

Manage L1 circuits and links with endpoints.

Manage historical PM data and alarms related to the client payloads for TXP-MR-2.5G and TXPP-MR-2.5G cards.

Retrieve and set RMON thresholds.

Perform the following steps to provision the payloads:


Step 1 Click the OTN tab.

Step 2 Disable FEC and G709 OTN. If G709 is not disabled, PPM cannot be enabled.

Step 3 Click the PPM tab and create a PPM for port 1.

Step 4 Provision the rate DVB-ASI or ISC1 by selecting the appropriate rate in the Port Rate drop-down list.



Note When using protection groups, you can provision only the working port.


The following figure shows the multirate 2.5G transponder, nonfiber-protected (TXP_MR_2.5G_xx.x) card faceplate.

Figure C-9 TXP_MR_2.5G_xx.x Module

The following figure shows the multirate 2.5G transponder, fiber-protected (TXPP_MR_2.5G_xx.x) card faceplate.

Figure C-10 TXPP_MR_2.5G_xx.x Module

For the 2.5G Multirate Transponder, the slot properties pane displays the following tabs: Module View, Identification, Card, PPM, Line, OTN, Loopback, Auto Laser Shutdown, Optical Thresh, Alarm Behavior, Protection, and Info. The tabs shown depend on the NE configuration.

C.2.3.1  Module View Tab

The Module View tab displays a graphic of the card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is display-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset or delete the card.

C.2.3.2  Identification Tab

The Identification tab allows you to view and update card identification information.

Table C-211 Field Descriptions for the Identification Tab 

Field
Description

Equipment Type

Displays the equipment type the slot is provisioned for.

Actual Equipment Type

Displays the actual card that is installed in the slot.

HW Part Number

Displays the part number that is printed on the top of the card.

Hardware Revision

Displays the hardware version number of the card.

Serial Number

Displays the serial number that is unique to each card.

CLEI Code

Displays the CLEI code.

Firmware Version

Displays the revision number of the software used by the ASIC chip installed on the card.

Product ID

Displays a product ID string of 63 characters maximum. If the card does not support the product ID, the field shows N/A.

Version ID

Displays a version ID string in the format "V99_." The version ID always begins with a V and ends with a space. If the card does not support the version ID, the field shows N/A.

Admin State

Displays the admin state of the card.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

Equipment State

Displays the equipment state of the card.

Alarm Profile

Sets the alarm profile for the card. Check the Suppress Alarms check box to suppress all alarms for this card and its port(s).


C.2.3.3  Card Tab

The Card tab allows you to view and update card information.

Table C-212 Field Descriptions for the Card Tab 

Field
Description

Framing Type

Read only. The framing type is unframed.

Termination Mode

Allows you to set the mode of termination. The termination mode can be transparent, multiplexer section (MS), or regeneration section (RS).

The Termination Mode is displayed as transparent and is read-only if you configured DVB-ASI or ISC1.

Regeneration Peer Slot

Allows you to select like cards so that you can configure a regeneration peer group.

Regeneration Group Name

(Optional) Allows you to set the name of the regeneration group.


C.2.3.4  PPM Tab

The PPM tab allows you to view and provision the PPM and the ports inside the PPM.

Table C-213 Field Descriptions for the PPM Tab 

Field
Description

Pluggable Number

Displays the identifier of the plugin module.

Actual Equipment Type

Displays the actual plugin module that is installed in the slot.

Equipment State

Displays the equipment state of the plugin module.

Admin State

Displays the status of the plugin module: In Service (IS); Out of Service-Maintenance (OOS_MT); Unlocked; or Locked, Maintenance.

Note You can edit the Admin State value only for actual equipment, not preprovisioned equipment.

Service State

Displays the service state of the plugin module. Values are:

Unknown—The state cannot be determined.

Not Installed—The plugin module is not installed.

Out of Service—The plugin module is installed but is not commissioned and is not carrying traffic.

In Service—The plugin module is commissioned and carrying traffic.


Table C-214 Description of Ports Configured in the PPM

Field
Description

Port

Displays the port configured in the PPM.

Rate

Displays the rate provisioned for the port.


C.2.3.4.1  Provision Pluggable Dialog Box

Click the Create button to launch the Provision Pluggable dialog box. This dialog box allows you to provision the PPM and to create the ports inside this entity. See Provision Pluggable Dialog Box for more information.

C.2.3.5  Line Tab

The Line tab allows you to configure line information.

If the card is installed on an ONS 15454 SONET NE, the tab contains the following subtabs:

Line Config Subtab

Section Trace Subtab

SONET Line Subtab

Section Thresh 15 Min Subtab

Section Thresh 1 Day Subtab

Line Thresh 15 Min Subtab

Line Thresh 1 Day Subtab

Wavelength Trunk Settings Subtab

If the card is installed on an ONS 15454 SDH NE, the tab contains the following subtabs:

Line Config Subtab

Section Trace Subtab

SDH Line Subtab

RS Thresh 15 Min Subtab

RS Thresh 1 Day Subtab

MS Thresh 15 Min Subtab

MS Thresh 1 Day Subtab

Wavelength Trunk Settings Subtab

C.2.3.5.1  Line Config Subtab

The Line Config subtab allows you to provision PPM parameters of a multirate 2.5G transponder card.

Table C-215 Field Descriptions for the Line Config Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a port name.

Administration State

The port administration state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

AINS Soak (H:M)

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency.


C.2.3.5.2  Section Trace Subtab

The Section Trace subtab allows you to change the section trace settings for the card.

Table C-216 Field Descriptions for the Section Trace Subtab 

Field
Description

Port No.

Displays the port number.

Trace Mode

The trace mode (Off/None or Manual).

Disable AIS/RDI on TIM-S

Allows you to disable the Alarm Indication Signal (AIS) and the Remote Defect Indication (RDI) when the path Trace Identifier Mismatch Section (TIM-S) alarm is detected.

Transmit Length

Select a transmit length for the trace.

Current Transmit String

Displays the current transmit string. The trail trace identifier is 64 bytes in length.

Current Expected String

Displays the current expected string; sets a new expected string.

Current Received String

Displays the current received string.


C.2.3.5.3  SONET Line Subtab

The SONET Line subtab allows you to view and change the SONET line settings of the card.

Table C-217 Field Descriptions for the SONET Line Subtab 

Field
Description

Port No.

Displays the port number.

Port Name

Allows you to add a name for the optical port.

Administration State

The port administration state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

SD BER

Sets the signal degrade bit error rate.

SF BER

Sets the signal fail bit error rate.

Type

Defines the port as SONET or SDH.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency.


C.2.3.5.4  Section Thresh 15 Min Subtab

The Section Thresh 15 Min subtab allows you to view and change the 15-minute section threshold information for the card.

Table C-218 Field Descriptions for the Section Thresh 15 Min Subtab 

Field
Description

Port No.

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.5  Section Thresh 1 Day Subtab

The Section Thresh 1 Day subtab allows you to view and change the 1-day section threshold information for the card.

Table C-219 Field Descriptions for the Section Thresh 1 Day Subtab 

Field
Description

Port No.

Displays the port number.

CV-S

Displays the coding violations section.

ES-S

Displays the errored seconds section.

SES-S

Displays the severely errored seconds section.

SEFS-S

Displays the severely errored framing seconds section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.6  Line Thresh 15 Min Subtab

The Line Thresh 15 Min subtab allows you to view and change the 15-minute line threshold information for the card.

Table C-220 Field Descriptions for the Line Thresh 15 Min Subtab 

Field
Description
Near End

Port No.

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Displays the failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port No.

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Displays the failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.7  Line Thresh 1 Day Subtab

The Line Thresh 1 Day subtab allows you to view and change the 1-day line threshold information for the card.

Table C-221 Field Descriptions for the Line Thresh 1 Day Subtab 

Field
Description
Near End

Port No.

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Displays the failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.

Far End

Port No.

Displays the optical port number.

ES-L

Displays the errored seconds line.

SES-L

Displays the severely errored seconds line.

CV-L

Displays the coding violations line.

UAS-L

Displays the unavailable seconds line information.

FC-L

Displays the failure count line.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.8  Wavelength Trunk Settings Subtab

The Wavelength Trunk Settings subtab allows you to change the wavelength and band settings for the card.

Table C-222 Field Descriptions for the Wavelength Trunk Settings Subtab 

Field
Description

Port Number

Displays the optical port number.

Port Name

Allows you to enter an optical port name.

Wavelength

Allows you to provision the wavelength frequency. The Wavelength column lists the correct wavelengths, depending on the type of card and the band selected. Refer to the Other Information field in the Equipment Inventory table for details of wavelengths supported. See 11.3.1.3  Equipment Inventory Table for CTC-Based NEs, page 11-11.

Band

The Band column reduces the number of selectable wavelengths (82/80 lambdas only). When the card is plugged in, the selection is disabled and the correct value of the band is displayed. When the card is preprovisioned, you can select either L- or C-band.


C.2.3.5.9  Line Config Subtab

The Line Config subtab allows you to provision PPM parameters of a multirate 2.5G transponder card.

Table C-223 Field Descriptions for the Line Config Subtab 

Field
Description

Port Number

Displays the port number.

Port Name

Allows you to add a port name.

Administration State

The port administration state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

ALS Mode

Displays the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

AINS Soak (H:M)

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency.


C.2.3.5.10  Section Trace Subtab

The Section Trace subtab allows you to change the section trace settings for the card.

Table C-224 Field Descriptions for the Section Trace Subtab 

Field
Description

Port No.

Displays the port number.

Trace Mode

The trace mode (Off/None or Manual).

Disable AIS/RDI on TIM-S

Allows you to disable the Alarm Indication Signal (AIS) and the Remote Defect Indication (RDI) when the path Trace Identifier Mismatch Section (TIM-S) alarm is detected.

Transmit Length

Select a transmit length for the trace.

Current Transmit String

Displays the current transmit string. The trail trace identifier is 64 bytes in length.

Current Expected String

Displays the current expected string; sets a new expected string.

Current Received String

Displays the current received string.


C.2.3.5.11  SDH Line Subtab

The SDH Line subtab allows you to view and change the SDH line settings of the card.

Table C-225 Field Descriptions for the SDH Line Subtab 

Field
Description

Port No.

Displays the optical port number.

Port Name

Allows you to enter an optical port name.

Administration State

The port administration state.

Service State

An autonomously generated state that gives the overall condition of the entity. Service states appear in the format Administrative_State-Operational_State, Status_Attribute.

AINS Soak

Automatic in-service soak. The determination of duration left before the traffic/termination transitions to IS state.

ALS Mode

Allows you to select the auto laser shutdown mode (Disabled, Auto Restart, Manual Restart, or Manual Restart for Test).

SD BER

Sets the signal degrade bit error rate.

SF BER

Sets the signal fail bit error rate.

Type

Defines the port as SONET or SDH.

Reach

Allows you to provision the reach value. You can choose Auto Provision, which allows the system to automatically provision the reach from the PPM reach value on the hardware. Choose one of the following reach distances:

Note The reach distance options that appear in the drop-down list depend on the card selected.

SR (short reach, up to 2 km distance)

SR 1 (up to 2 km distance)

IR 1 (intermediate reach, up to 15 km distance)

IR 2 (up to 40 km distance)

LR 1 (long reach, up to 40 km distance)

LR 2 (up to 80 km distance)

LR 3 (up to 80 km distance)

I1

S1

S2

L1

L2

L3

SX (up to 550 m or 270 m distance based on 50 um/62.5 um diameter fiber)

LX (up to 10 km or 550 m distance based on 50 um/62.5 um diameter fiber)

CX

T

DX (up to 40 km distance)

HX (up to 40 km distance)

ZX (up to 80 km distance)

VX (up to 100 km distance)

Wavelength

Allows you to provision the wavelength frequency.


C.2.3.5.12  RS Thresh 15 Min Subtab

The RS Thresh 15 Min subtab allows you to view and change the 15-minute regeneration section threshold for the card.

Table C-226 Field Descriptions for the RS Thresh 15 Min Subtab 

Field
Description

Port No.

The port number.

EB-RS

Errored blocks regenerator section.

ES-RS

Errored seconds regenerator section.

SES-RS

Severely errored seconds regenerator section.

BBE-RS

Background block errors regenerator section.

UAS-RS

Unavailable seconds regenerator section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.13  RS Thresh 1 Day Subtab

The RS Thresh 1 Day subtab allows you to view and change the 1-day regeneration section threshold for the card.

Table C-227 Field Descriptions for the RS Thresh 1 Day Subtab 

Field
Description

Port No.

The port number.

EB-RS

Errored blocks regenerator section.

ES-RS

Errored seconds regenerator section.

SES-RS

Severely errored seconds regenerator section.

BBE-RS

Background block errors regenerator section.

UAS-RS

Unavailable seconds regenerator section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.14  MS Thresh 15 Min Subtab

The MS Thresh 15 Min subtab allows you to view and change the 15-minute near- and far-end multiplex section threshold for the card.

Table C-228 Field Descriptions for the MS Thresh 15 Min Subtab 

Field
Description

Port No.

The port number.

EB-MS

Errored blocks multiplexer section.

ES-MS

Errored seconds multiplexer section.

SES-MS

Severely errored seconds multiplexer section.

BBE-MS

Background block errors multiplexer section.

UAS-MS

Unavailable seconds multiplexer section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.15  MS Thresh 1 Day Subtab

The MS Thresh 1 Day subtab allows you to view and change the 1-day near- and far-end multiplex section threshold for the card.

Table C-229 Field Descriptions for the MS Thresh 1 Day Subtab 

Field
Description

Port Number

The port number.

EB-MS

Errored blocks multiplexer section.

ES-MS

Errored seconds multiplexer section.

SES-MS

Severely errored seconds multiplexer section.

BBE-MS

Background block errors multiplexer section.

UAS-MS

Unavailable seconds multiplexer section.

Reset to Defaults button

Resets the value of the port parameters to the default value.


C.2.3.5.16  Wavelength Trunk Settings Subtab

The Wavelength Trunk Settings subtab allows you to change the wavelength and band settings for the card.

Table C-230 Field Descriptions for the Wavelength Trunk Settings Subtab 

Field
Description

Port Number

Displays the optical port number.

Port Name

Allows you to enter an optical port name.

Wavelength

Allows you to provision the wavelength frequency. The Wavelength column lists the correct wavelengths, depending on the type of card and the band selected. Refer to the Other Information field in the Equipment Inventory table for details of wavelengths supported. See 11.3.1.3  Equipment Inventory Table for CTC-Based NEs, page 11-11.

Band

The Band column reduces the number of selectable wavelengths (82/80 lambdas only). When the card is plugged in, the selection is disabled and the correct value of the band is displayed. When the card is preprovisioned, you can select either L- or C-band.


C.2.3.6  OTN Tab

The OTN tab allows you to change the line optical transport network (OTN) settings for multirate transponder cards. If you provisioned the payloads DVB-ASI or ISC1, all other subtabs except OTN Line are blank.


Note OTN is supported only for trunk ports.


Table C-231 Field Descriptions for the OTN Tab 

Field
Description
G.709 Thresh 15 Min
SM (OTUK) Near End, Far End

Port No.

The port number.

BBE-SM

Background block errors.

ES-SM

Errored seconds.

SES-SM

Severely errored seconds.

UAS-SM

Unavailable seconds.

FC-SM

Failure count.

Reset to Defaults button

Resets the value of the port parameters to the default value.

PM (ODUK) Near End, Far End

Port No.

The port number.

BBE-PM

Background block errors.

ES-PM

Errored seconds.

SES-PM

Severely errored seconds.

UAS-PM

Unavailable seconds.

FC-PM

Failure count.

Reset to Defaults button

Resets the value of the port parameters to the default value.

G.709 Thresh 1 Day
SM (OTUK) Near End, Far End

Port No.

The port number.

BBE-SM

Background block errors.

ES-SM

Errored seconds.

SES-SM

Severely errored seconds.

UAS-SM

Unavailable seconds.

FC-SM

Failure count.

Reset to Defaults button

Resets the value of the port parameters to the default value.

PM (ODUK) Near End, Far End

Port No.

The port number.

BBE-PM

Background block errors.

ES-PM

Errored seconds.

SES-PM

Severely errored seconds.

UAS-PM

Unavailable seconds.

FC-PM

Failure count.

Reset to Defaults button

Resets the value of the port parameters to the default value.

FEC Thresh 15 Minutes

Port Number

Displays the port number.

Bit Errors Corrected

Displays the bit errors corrected in 15-minute intervals.

Uncorrectable Words

Displays the uncorrectable words in 15-minute intervals.

FEC Thresh 1 Day

Port Number

Displays the port number.

Bit Errors Corrected

Displays the bit errors corrected in one-day intervals.

Uncorrectable Words

Displays the uncorrectable words in one-day intervals.

Trail Trace Identifier

Port No.

The port number.

Level

Displays the trail trace identifier level (Section or Path).

Trace Mode

Allows you to set the trace mode (Off or Manual).

Disable FDI on TTIM

Allows you to disable forward defect indication (FDI) for trail trace identifier mismatch alarms.

Current Transmit String

Displays the current transmit string. The trail trace identifier is 64 bytes in length.

Current Expected String

Displays the current expected string.

Current Received String

Displays the current received string.

OTN Line

Port No.

The port number.

G.709 OTN

Disables or enables the G.709 OTN feature.

If you provisioned the payloads DVB-ASI or ISC1, this field displays the current status of the G.709 OTN feature: enabled or disabled.

FEC

Disables or enables forward error correction.

If you provisioned the payloads DVB-ASI or ISC1, this field displays the status of forward error correction: enabled or disabled.

Note OTN must be enabled before you can enable FEC.

SF BER

The signal fail bit error rate.

SD BER

The signal degrade bit error r