Installation and Upgrade Guide for the Cisco Secure Access Control System 5.1
Installing and Configuring the Cisco Secure Access Control Server
Downloads: This chapterpdf (PDF - 135.0KB) The complete bookPDF (PDF - 5.76MB) | Feedback

Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Table Of Contents

Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Installation Using the CSACS-1121 Series Appliance

Installing the ACS Server

Running the Setup Program

Verifying the Installation Process

Resetting the Administrator Password

Reimaging the ACS Server


Installing and Configuring the Cisco Secure Access Control System with CSACS-1121


This chapter describes how to install and initially configure CSACS-1121 and the ACS 5.1 server.

This chapter contains:

Installation Using the CSACS-1121 Series Appliance

Installing the ACS Server

Resetting the Administrator Password

Reimaging the ACS Server

Installation Using the CSACS-1121 Series Appliance

The CSACS-1121 appliance is preinstalled with the ACS 5.1 software. This section gives you an overview of the installation process and the tasks that you must perform before installing ACS.

Before you begin installing ACS 5.1, you must:

1. Open the box and check the contents. See Chapter 3, "Unpacking and Checking the Contents of Your Shipment."

2. Read Chapter 2, "Introducing the Cisco 1121 Secure Access Control System Hardware."

3. Read the general precautions and safety warnings in Chapter 3, "Preparing to Install the Cisco 1121 Secure Access Control System Hardware."

4. Install the appliance in the rack. See Chapter 4, "Installing the Cisco 1121 Secure Access Control System Hardware."

5. Connect the CSACS-1121 to the network and appliance console. See Chapter 4, "Connecting Cables."

6. Power up the CSACS-1121 appliance. See Chapter 4, "Powering Up the CSACS-1121 Series Appliance."

7. Run the setup command at the CLI prompt to configure the initial settings for the ACS server. See Running the Setup Program.

Installing the ACS Server

This section describes the installation process for the ACS server on the CSACS-1121 Series appliance.

This section contains:

Running the Setup Program

Verifying the Installation Process

Running the Setup Program

This section describes the setup process to install the ACS server.

The setup program launches an interactive command-line interface (CLI) that prompts you for the required parameters. An administrator can use the console or a dumb terminal to configure the initial network settings and provide the initial administrator credentials for the ACS 5.1 server using the setup program. The setup process is a one-time configuration task.

To install the ACS server:


Step 1 Power on the appliance.

The setup prompt appears:

Please type `setup' to configure the appliance

localhost login:

Step 2 At the login prompt, enter setup and press Enter.

The console displays a set of parameters. You must enter the parameters as described in Table 5-1.


Note You can interrupt the setup process at any time by typing Ctrl-C before the last setup value is entered.


Table 5-1 Network Configuration Parameters 

Prompt
Default
Conditions
Description

Host Name

<localhost>

First letter must be an ASCII character.

Length must be from 3 to 19 characters.

Valid characters are alphanumeric (A-Z, a-z, 0-9), hyphen (-), and the first character must be a letter.

Enter the hostname.

IPv4 IP Address

None, network specific

Must be a valid IPv4 address between 0.0.0.0 and 255.255.255.255.

Enter the IP address.

IPv4 Netmask

None, network specific

Must be a valid IPv4 address between 0.0.0.0 and 255.255.255.255.

Enter a valid netmask.

IPv4 Gateway

None, network specific

Must be a valid IPv4 address between 0.0.0.0 and 255.255.255.255.

Enter a valid default gateway.

Domain Name

None, network specific

Cannot be an IP address.

Valid characters are ASCII characters, any numbers, hyphen (-), and period (.).

Enter the domain name.

IPv4 Primary Name Server Address

None, network specific

Must be a valid IPv4 address between 0.0.0.0 and 255.255.255.255.

Enter a valid name server address.

Add/Edit another nameserver

None, network specific

Must be a valid IPv4 address between 0.0.0.0 and 255.255.255.255.

To configure multiple name servers, enter Y.

Username

admin

The name of the first administrative user. You can accept the default or enter a new username.

Must be from 3 to 8 characters, and must be alphanumeric (A-Z, a-z, 0-9).

Enter the username.

Admin Password

None

No default password. Enter your password.

The password must be at least six characters in length, have at least one lowercase letter, one uppercase letter, and one number.

In addition:

Save the user and password information for the account that you set up for initial configuration.

Remember and protect these credentials because they allow complete administrative control of the ACS hardware, the CLI, and the application.

If you lose your administrative credentials, you can reset your password by using the ACS 5.1 installation CD.

Enter the password.


The console requests for the parameters as shown below:

localhost login: setup

Enter hostname[]: acs-server-1

Enter IP address[]: 209.165.200.225

Enter IP default netmask[]: 255.255.255.0

Enter IP default gateway[]: 209.165.200.1

Enter default DNS domain[]: mycompany.com

Enter Primary nameserver[]: 209.165.200.254

Add/Edit another nameserver? Y/N : n

Enter username [admin]: admin

Enter password:

Enter password again:

Pinging the gateway...

Pinging the primary nameserver...

Do not use `Ctrl-C' from this point on...

Appliance is configured

Installing applications...

Installing acs...

Generating configuration...

Rebooting...

After the ACS server is installed, the system reboots automatically.

Now, you can log in to ACS using the CLI username and password that was configured during the setup process.


Note You can use this username and password to log in to ACS only via the CLI.



Verifying the Installation Process

To verify that you have correctly completed the installation process:


Step 1 When the system reboots, at the login prompt enter the username you configured during setup, and press Enter.

Step 2 At password prompt, enter the password you configured during setup, and press Enter.

Step 3 To verify that the application has been installed properly, enter show application, and press Enter.

The console displays:

<name> <Description>

acs ACS 5.1

Step 4 To check the release and ACS version installed, at the system prompt, enter show application version acs, and press Enter.

The console displays:

Cisco ACS VERSION INFORMATION

-----------------------------

Version : 5.1.0

Release : B.1083


Note The build number may change for different versions of this release.


Step 5 To check the status of ACS processes, at the system prompt, enter show application status acs, and press Enter.

The console displays:

ACS role: PRIMARY

Process 'database' running

Process 'management' running

Process 'runtime' running

Process 'view-database' running

Process 'view-jobmanager' running

Process 'view-alertmanager' running

Process 'view-collector' running

Process 'view-logprocessor' running



Note To get the latest ACS patches and to keep your ACS up-to-date, visit http://www.cisco.com/cgi-bin/tablebuild.pl/acs5_patches


Resetting the Administrator Password

If you are not able to log in to the system due to loss of administrator password, you can use the ACS 5.1 Recovery DVD to reset the administrator password.

To reset the administrator password:


Step 1 Power up the appliance.

Step 2 Insert the ACS 5.1 Recovery DVD.

The console displays:

Welcome to Cisco Secure ACS 5.1 Recovery - CSACS 1121

To boot from hard disk press <Enter>

Available boot options:

[1] Cisco Secure ACS 5.1 Installation (Keyboard/Monitor)

[2] Cisco Secure ACS 5.1 Installation (Serial Console)

[3] Reset Administrator Password (Keyboard/Monitor)

[4] Reset Administrator Password (Serial Console)

<Enter> Boot from hard disk

Please enter boot option and press <Enter>.

boot:

Step 3 To reset the administrator password, at the system prompt, enter 3 if you are using a keyboard and video monitor, or enter 4 if you are using a serial console port.

Step 4 The console displays a set of parameters. You must enter the parameters as described in Table 5-2.

Table 5-2 Password Reset Parameters 

Parameter
Description

Admin username

Enter the number of the administrator whose password you want to reset.

Password

Enter the new password for the administrator.

Verify password

Enter the password again.

Save change & Reboot

Enter Y to save.


The console displays:

Admin username:

[1]:admin

[2]:admin2

[3]:admin3

Enter number of admin for password recovery:1

Password:

Verify password:

Save change&reeboot? [Y/N]:


Reimaging the ACS Server

To reimage the ACS server:


Step 1 Power up the appliance.

Step 2 Insert the ACS Recovery DVD.

The console displays:

Welcome to Cisco Secure ACS 5.1 Recovery - Cisco CSACS 1121

To boot from hard disk press <Enter>

Available boot options:

[1] Cisco Secure ACS 5.1 Installation (Keyboard/Monitor)

[2] Cisco Secure ACS 5.1 Installation (Serial Console)

[3] Reset Administrator Password (Keyboard/Monitor)

[4] Reset Administrator Password (Serial Console)

<Enter> Boot from hard disk

Please enter boot option and press <Enter>.

boot:

Step 3 At the console prompt, enter 1 if you are using a keyboard and video monitor, or enter 2 if you are using a serial console port, and press Enter.

The reimage process uninstalls the existing ADE-OS and ACS versions, and installs the latest versions. For installation process, refer to the section Running the Setup Program.