Release Notes for the Cisco Broadband Access Center DPE-2115 Recovery CD-ROM

Table Of Contents

Release Notes for the Cisco Broadband Access Center DPE-2115 Recovery CD-ROM

Contents

Introduction

Using the DPE-2115 Recovery CD-ROM

Obtaining Documentation, Obtaining Support, and Security Guidelines

Release Notes for the Cisco Broadband Access Center DPE-2115 Recovery CD-ROM

---

June 15, 2007

Contents

•Introduction

•Using the DPE-2115 Recovery CD-ROM

•Obtaining Documentation, Obtaining Support, and Security Guidelines

Introduction

This release note describes how to use the Recovery CD-ROM for the Cisco Broadband Access Center (BAC) Device Provisioning Engine-2115 (DPE-2115). It provides instructions on reinstalling or reimaging the original software image installed on the DPE-2115.

---

Note The DPE-2115 recovery image can be installed locally only. You cannot reinstall the original software over a network.

---

Using the DPE-2115 Recovery CD-ROM

The Recovery CD-ROM contains an image of the software that was originally installed on
the DPE-2115.

---

Caution When reimaging the DPE, all data stored on the DPE is lost. Once the reimaging process is complete, you must reconfigure the DPE-2115 with the configuration settings that you used on the previous image of the DPE.

---

To reimage your DPE-2115:

---

Step 1 Insert the BAC DPE-2115 Recovery CD-ROM into the DPE-2115 and close the CD-ROM drive.

Step 2 Power down the DPE by pressing and holding the power button for at least 5 seconds.

Step 3 Power up the DPE by pressing and holding the power button for at least 5 seconds. Powering up the DPE boots the CD and prompts you to begin.

Step 4 When the boot: prompt appears, enter:

install 

The installation program begins to install the recovery image.

Step 5 The reimage process completes in approximately 2 minutes and the Recovery CD is ejected from the drive. Once the CD is ejected, the DPE automatically reboots.

---

Note During the reboot, an extensive array of technical data concerning the DPE and the programs running on it appears.

---

Step 6 Once the reboot is complete, a verification procedure runs. At the end of this procedure, this
prompt appears:

Test Completed ok. Enter a <CR> to power off. 

Step 7 Press Return and wait for the "system halted" message to appear. This message indicates that the recovery process is complete.

Step 8 Power cycle the DPE as described in Step 2 of this procedure.

---

Obtaining Documentation, Obtaining Support, and Security Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R)

© 2007 Cisco Systems, Inc. All rights reserved.