Cisco IOS XR System Error Message Reference Guide, Release 4.3.x
Simple Network Management Protocol (SNMP) Messages
Downloads: This chapterpdf (PDF - 512.0 KB) The complete bookPDF (PDF - 18.29 MB) | Feedback

Table of Contents

Simple Network Management Protocol (SNMP) Messages

AFMONMIB Messages

ATM_MIB Messages

ATMSNMP Messages

BULKFILEMIB Messages

CBQOSMIB Messages

CISCOBGPPAMIB Messages

CISCOPROCESSMIB Messages

CISCOSYSTEMMIB Messages

COPYMIB Messages

CSCMIB Messages

ENTITYMIB Messages

FTPCLIENTMIB Messages

HSRPMIB Messages

IFINDEX_PROVIDER Messages

IFMIB_IFSPECIFIC_CLIENT Messages

IFMIB_IFSPECIFIC_SERVER Messages

IFMIB Messages

IPMIB Messages

LIBSNMP Messages

MACSTATMIB Messages

MIB Messages

NLMMIB Messages

PINGMIB Messages

QOSMIB Messages

SNMP_IPC Messages

SNMP Messages

SONETMIB Messages

SONETMIBAPI Messages

SONETMIBCORE Messages

SYSLOGMIB Messages

UDPSNMP Messages

UTIL Messages

VLANIFMIB Messages

Simple Network Management Protocol (SNMP) Messages

This section contains all Simple Network Management Protocol related System Error Messages, such as BGP, MIB, CONFIG MIB, SNMP agent, and so forth. MIB location does not matter.

AFMONMIB Messages

Error Message %SNMP-AFMONMIB-3-ERR_MEM_ALLOC

Insufficient Memory to perform [chars] operation

Explanation The MIB had trouble allocating memory.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-AFMONMIB-3-ERR_MUTEX

Mutex [chars] failed

Explanation The MIB had trouble locking/unlocking mutex.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

ATM_MIB Messages

Error Message %SNMP-ATM_MIB-3-INIT_ERR

ATM MIB support initialization failed ([chars]%s)

Explanation An error occurred while initializing ATM MIB support in snmpd process. If this occurred during process startup, then the process may be restarted.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ATMSNMP Messages

Error Message %SNMP-ATMSNMP-3-IFMGR

ATM SNMP: [chars]: [chars]: [dec]: [dec]

Explanation A high severity error is encountered.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-ATMSNMP-3-info

ATM SNMP: [chars]

Explanation debug msg

Recommended Action None

Error Message %SNMP-ATMSNMP-3-SYSDB

ATM SNMP: [chars]: [chars]: [dec]

Explanation This message indicates the ATM SNMP library fails to perform a SYSDB operation. *DDTS*

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

BULKFILEMIB Messages

Error Message %SNMP-BULKFILEMIB-3-ERR_MEM_ALLOC

Insufficient memory to perform [chars] operation

Explanation No memory in the process.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-BULKFILEMIB-3-ERR_THREAD_CREATE

Could not create a bulk file processing thread

Explanation There are no resources available to create a bulk file processing thread

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CBQOSMIB Messages

Error Message %SNMP-CBQOSMIB-3-ERR_MEM_ALLOC

Insufficient Memory to perform [chars] operation

Explanation The MIB had trouble allocating memory.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-CBQOSMIB-3-ERR_MUTEX

Mutex [chars] failed

Explanation The MIB had trouble locking/unlocking mutex.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

CISCOBGPPAMIB Messages

Error Message %SNMP-CISCOBGPPAMIB-3-ERR_MEM_ALLOC

Failed to get memory for [chars]

Explanation Memory unavailable

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

CISCOPROCESSMIB Messages

Error Message %SNMP-CISCOPROCESSMIB-3-ERR_MEM_ALLOC

Unable to allocate memory for process name

Explanation The MIB had trouble allocating memory for process name’

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

CISCOSYSTEMMIB Messages

Error Message %SNMP-CISCOSYSTEMMIB-3-CLOCK

Clock operation Error: [chars]

Explanation The MIB had trouble in spawning a process.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-CISCOSYSTEMMIB-3-EVENT_ASYNC_ALLOC

Failed to allocate asynchronous event: [chars]

Explanation An internal software error occurred.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CISCOSYSTEMMIB-3-SPAWN

Spawn Error: [chars]

Explanation The MIB had trouble in spawning a process.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-CISCOSYSTEMMIB-3-SYSDB_ACCESS

Sysdb related error: [chars]

Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-CISCOSYSTEMMIB-3-TARGET_CFG_PROBLEM

[chars] : Failed to [chars] target config for [chars] : [chars]

Explanation An internal software error occurred.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CISCOSYSTEMMIB-3-TIMER

Timer Error: [chars]

Explanation Timer error

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-CISCOSYSTEMMIB-7-CREATE_EVM

Could not create event manager for [chars] ([chars])

Explanation Attempt to create an event manager fails for some reason.

Recommended Action Use the status to determine the reason.

COPYMIB Messages

Error Message %SNMP-COPYMIB-3-ENTRYNONE

Entry for id [dec] doesn’t exist.

Explanation An attempt to remove an entry from a queue was made, but the entry was not found.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-COPYMIB-3-ERR_MEM_ALLOC

Insufficient memory to [chars]

Explanation No memory to perform edm or bag operations.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CSCMIB Messages

Error Message %SNMP-CSCMIB-7-CSC_ASSERT

Invalid codepath encountered - exitting.

Explanation An invalid codepath has been encountered - the process is exitting and restarting.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CSCMIB-7-CSC_BAG

The MIB was unable to marshall or unmarshall a set of data, error: [chars]

Explanation This may be due to invalid data being sent by the agent or request, or due to an error in the data-marshalling infrastructure. The current request cannot be completed. Check the request and try again.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CSCMIB-7-CSC_OCTETSTRING

Failed to convert an SNMP supplied OctetString to a string.

Explanation An illegal string was passed in to the MIB by the agent. The current request cannot be completed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CSCMIB-7-CSC_SNMP

The SNMP request did not specify an index.

Explanation The SNMP management station tried a set request without specifying a request index. Check the request and try again.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CSCMIB-7-INVALID_ARG

Internal error occurred: [chars]

Explanation The MIB has reached an expected state, and will not be able to service the current request.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CSCMIB-7-NOMEM

Could not allocate memory

Explanation The MIB has failed to aquire the required amount of memory.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-CSCMIB-7-SYSDB_ACCESS

The MIB was unable to access the system database, error: [chars]

Explanation The MIB was unable to read to or write from the system database, so will be unable to provide some requested MIB data.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-CSCMIB-7-SYSDB_BIND

The MIB was unable to connect to the system database, error: [chars]

Explanation The MIB was unable to connect to the system database, so will be unable to provide the MIB data. This may be because the communications infrastructure is not yet up.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ENTITYMIB Messages

Error Message %SNMP-ENTITYMIB-3-INIT_ERROR

Failure during initialization. Error: [chars].

Explanation A failure occured during the initialization of the process.

Recommended Action Restart mibd_entity

FTPCLIENTMIB Messages

Error Message %SNMP-FTPCLIENTMIB-3-NOMEM

Insufficient memory to perform [chars] operation

Explanation No memory in the process.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-FTPCLIENTMIB-3-NOTHREADCREATE

Could not create a FTP request processing thread

Explanation There are no resources available to create a FTP request processing thread

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

HSRPMIB Messages

Error Message %SNMP-HSRPMIB-3-ERR_CONN

The HSRP MIB could not connect to the HSRP process. ([chars])

Explanation The HSRP MIB was unable to create a SysDB connection to the HSRP process for the purpose of retrieving management information.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-HSRPMIB-4-WARN_DEBUG

Failed to register HSRP MIB debug control: [chars]

Explanation During initialisation of the HSRP MIB, it was not possible to register to be notified of changes to the debugging state. The MIB will continue to function, but it will not be possible to turn on debugging for the MIB.

Recommended Action If debugging is essential, then restart SNMP. This will reinitialize the HSRP MIB. If the problem persists, do the following. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-HSRPMIB-4-WARN_NOTIFY

Failed to register for notification of state changes. ([chars])

Explanation During initialisation of the HSRP MIB, it was not possible to register to be notified of changes in active state of an HSRP group. The MIB will continue to function, but no traps will be generated for the cHsrpStateChange notification.

Recommended Action Restart SNMP. This will re-initialize the HSRP MIB. If the problem persists, do the following. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-HSRPMIB-4-WARN_OID

Failed to construct OID in trap generation. ([dec])

Explanation An OID (object identifier) string failed to be constructed during trap generation. The trap for a cHsrpStateChange notification did not get sent.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

IFINDEX_PROVIDER Messages

Error Message %SNMP-IFINDEX_PROVIDER-3-DUPLICATE_INDEX

IF-MIB duplicate interface index detected during [chars] operation.

Explanation An attempt to allocate an interface index has failed because it had been previously allocated.

Recommended Action If this message is generated for a persistence file restore operation, delete the interface index persistence file. If this message is generated for a process restart or Standby RP synchronization operation, use the show snmp interface command to perform a sanity check of the interface name to index mappings. If any expected interface index assignments are missing, restart the mibd_interface process. Network management applications should rediscover interfaces.

Error Message %SNMP-IFINDEX_PROVIDER-3-IFNAME_TO_INDEX

Failed to [chars] for [chars]: [chars]

Explanation Failed to get the ifindex value for the given interface name

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-IFINDEX_PROVIDER-3-INTERFACE_INDEX_PERSISTENCE_PARTIAL_RESTORE

IF-MIB unable to restore all interface indices from interface index persistence file.

Explanation An attempt to restore all interface indices from the interface index persistence file has failed.

Recommended Action Remove and re-generate the interface index persistence file by disabling and enabling persistence in the configuration. Network management applications should rediscover interfaces.

Error Message %SNMP-IFINDEX_PROVIDER-3-INTERNAL

[chars]

Explanation An unexpected internal error occurred in the ifindex subsystem.

Recommended Action Copy the error message exactly as it appears on the console or in the system log. Call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-IFINDEX_PROVIDER-3-SERVER_ERROR

[chars] error during [chars]: [chars]

Explanation An error occurred while communicating with one of the servers

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-IFINDEX_PROVIDER-7-LTRACE_INIT_ERROR

’[chars]’ error during intialization of LW tracing for ifindex provider

Explanation An error occured while initializing LW tracing for ifindex provider library.

Recommended Action No action is required.

IFMIB_IFSPECIFIC_CLIENT Messages

Error Message %SNMP-IFMIB_IFSPECIFIC_CLIENT-3-ERR_INV_MSG

Received an invalid message, field ’[chars]’ is incorrect

Explanation The message received requesting an operation is malformed.

Recommended Action ’No action is required.’

Error Message %SNMP-IFMIB_IFSPECIFIC_CLIENT-3-ERR_OPER_INTF

Failed to [chars] ifIndex equals [dec] to/from ifSpecific tableId equals [dec]; due to [chars]

Explanation The operation requested could not be performed due to an internal error.

Recommended Action ’No action is required.’

Error Message %SNMP-IFMIB_IFSPECIFIC_CLIENT-3-ERR_OPER_TABLE

SNMP MIB interface specific (e.g. SONET, Ethernet) table operation error (operation equals [chars], table id equals [dec], reason equals [chars])

Explanation ’A software problem has been detected that prevents SNMP from ’ ’completing the requested interface specific table operation. ’ ’Operation of the interface specific MIB (e.g. SONET, Ethernet) is ’ ’impacted.’

Recommended Action ’If this message is encountered, copy the System Message exactly as ’ ’it appears on the console or in the system log, contact your Cisco ’ ’technical support representative, and provide the representative with ’ ’the information.’

Error Message %SNMP-IFMIB_IFSPECIFIC_CLIENT-6-ERR_DBG_FAILED

Failed to [chars] debugging of IF-MIB IfSpec Client DLL, due to [chars]

Explanation The operation requested could not be performed due to an internal error.

Recommended Action ’No action is required.’

IFMIB_IFSPECIFIC_SERVER Messages

Error Message %SNMP-IFMIB_IFSPECIFIC_SERVER-6-ERR_DBG_FAILED

Failed to [chars] debugging of IF-MIB IfSpec Server DLL, due to [chars]

Explanation The operation requested could not be performed due to an internal error.

Recommended Action ’No action is required.’

IFMIB Messages

Error Message %SNMP-IFMIB-3-ERR_MEM_ALLOC

Failed to [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action ’Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.’

Error Message %SNMP-IFMIB-3-ERR_REGEXP_COMP

Failed to compile regexp:[chars], Error : [chars]

Explanation Failed to compile given regular expression

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-IFMIB-3-ERR_SYSDB

Failed to [chars], err: [chars]

Explanation Ifmib has failed during sysdb operation.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-IFMIB-3-GEN_ERROR

IFMIB DLL error:[chars]

Explanation Failed to do DLL operation

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-IFMIB-4-ERR_SYSDB_APPLY

Configuration got applied with Err:[chars]. Remove this configuration from the system

Explanation verification for ’snmp interface subset’ command failed because of some invalid input. Ifmib database is not updated because of this config but in sysdb, config might have happened. For recovering from this ’no snmp interface subset subset-no’ is required.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-IFMIB-4-ERR_SYSDB_REGISTER

Failed to register with sysdb for bundle config [chars]

Explanation Ifmib has failed to register with sysdb for bundle config notification. Ifmib will retry registering with sysdb. If the syslog message is seen continuously then there could be a problem either with sysdb or ifmib.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Collect ’show tech sysdb’, ’show logging’ and ’show tech snmp ifmib’.

IPMIB Messages

Error Message %SNMP-IPMIB-3-BAG

An operation on a bag failed: [chars]

Explanation A problem occurred while encoding or decoding information from a bag.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-IPMIB-3-SYSDB_ACCESS

Operation [chars] failed, error [chars]

Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

LIBSNMP Messages

Error Message %SNMP-LIBSNMP-3-NOMEM_FOR_INIT

snmpd is being shut down due to lack of memory required for initialization. Try restarting snmpd after freeing some memory

Explanation Not enough memory was available for snmpd to set up its internal data structures.

Recommended Action Try stopping some running processes, or wait awhile before restarting snmpd. If the problem persists after several tries, please contact your customer support representative.

MACSTATMIB Messages

Error Message %SNMP-MACSTATMIB-4-MIB_INIT

Initialization Failure: [chars]: [chars]

Explanation The MAC accounting MIB was unable to initialize successfully. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

MIB Messages

Error Message %SNMP-MIB-3-BADTRANSPORT

Attempt to [chars] unknown transport type: [dec]

Explanation Attempted to perform the indicated operation on an unknown transport type. This is an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-MIB-3-CHKPT

[chars]: [chars]

Explanation Failed in checkpointing the data, it could reading/writing, creating object or registering with existing checkpoint_table.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-MIB-3-NOINIT

MIB Library not properly initialized

Explanation The MIB library was not properly initialized by the SNMP agent. This is an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-MIB-3-SYSUPTIME

Failed to retrieve sysUpTime: [chars]

Explanation Failed to read the system clock, and thus determine what sysUpTime is. The result is that sysUpTime will latch at its last known value.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

NLMMIB Messages

Error Message %SNMP-NLMMIB-3-ERR_MEM_ALLOC

Failed to [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action ’Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.’

PINGMIB Messages

Error Message %SNMP-PINGMIB-3-BADID

Server received [chars] request with no valid id

Explanation Bad ID error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-BAG

Bag encode/decode Error : [chars]

Explanation Error bag encoding/decoding

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-ENTRYNONE

Entry for id [dec] doesn’t exist

Explanation Entry for id not found

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-EVENT_BLOCK

event block call failed: [chars]

Explanation Event block call failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-INIT

Failed to [chars], cannot initialize: [chars]

Explanation initialization failed error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-MSGFAIL

SysDB failed to process incoming message: [chars]

Explanation Sysdb error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-MUTEX_INIT

Failed to init pthread mutex: [chars]

Explanation Failed to init pthread mutex

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-NOMEM

Insufficient memory to perform [chars] operation

Explanation Out of memory error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-NOTHREADCREATE

Could not create a PING request processing thread

Explanation There are no resources available to create a PING request processing thread

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-PTHREAD_COND_INIT

Pthread cond wait call failed: [chars]

Explanation pthread cond wait call failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-SYSDB_ACCESS

SysDB failed to process incoming message : [chars]

Explanation Sysdb Err

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-SYSMGR_PROC_READY

Failed to notify sysmgr the completion of initialization: [chars]

Explanation Failed to notify sysmgr the completion of initialization

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-TIMER

Failed to create [chars] timer

Explanation Timer error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-TIMERNOMEM

Insufficient memory to create timer for entry [dec]

Explanation Insufficient memory to create timer for entry error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-TIMERNONE

Failed to find timer for entry id [dec]

Explanation Failed to find timer for entry

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-TRAPOID

Failed to create trap OID for [chars]

Explanation Failed to create trap OID error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-3-UNKNOWNMSG

Received unknown event type: [dec]

Explanation Received unknown event type error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-PINGMIB-7-DEBUG_REGISTER

debug register call failed: [chars]

Explanation debug register call failed. No action needed. System will recover by itself.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

QOSMIB Messages

Error Message %SNMP-QOSMIB-3-ERR_MEM_ALLOC

Insufficient Memory to perform [chars] operation

Explanation The MIB had trouble allocating memory.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %SNMP-QOSMIB-3-ERR_NO_ENT

Entry for [chars] not found in [chars] or insufficient memory

Explanation The particular entry was not found in the list or MIB had trouble allocating memory.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

SNMP_IPC Messages

Error Message %SNMP-SNMP_IPC-4-ERR_MEM

Failed to allocate memory for [chars]

Explanation SNMP library failed to allocate memory for an object due to low memory conditions in the System.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP_IPC-4-INTERNAL

[chars] :[chars]

Explanation SNMP library incurred an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SNMP Messages

Error Message %SNMP-SNMP-3-CONFIGFAIL

Failed to [chars] [chars]: [chars]

Explanation Failed to perform the indicated configuration operation. This could be due to a low memory condition, an unsane configuration, or an internal software error. Failed in Host config: Received a good tuple for the snmp-server host CLI command, but could not configure it. This is likely due to lack of memory, which may be a transient condition, or may be due to SNMP supporting too many MIBS with large amounts of data. Try this command again after a few minutes. If it continues to fail, you may wish to undo some SNMP configurations and then retry the command.

Recommended Action Examine the configuration and ensure that it is sane. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *SH_CMD config*

Error Message %SNMP-SNMP-3-DATASIZE

Data size exceeded for [chars]. Length of data is %zd(max length is %zd)

Explanation The maximum size of the data has been exceeded. This could be due to user configuration or internal error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-ERR_DLL_LOAD

Failed to load [chars]: [chars]

Explanation Failed to load the given MIB, for the given reason. This could be due to a low memory condition.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-3-ERR_DLL_UNKNOWN

Failed to map [chars] to an address: [chars]

Explanation An attempt to map a MIB DLL symbolic name to an address failed. This MIB will be unloaded. This could be due to a corrupted MIB configuration file, a corrupted DLL, or a MIB configuration file that is out-of-sync with its corresponding MIB DLL.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Also provide a copy of the MIB DLL and its associated MIB configuration file.

Error Message %SNMP-SNMP-3-ERR_EVM_EVENT_BLOCK

Received error from event_wait: [chars]

Explanation SNMP receives messages from an event manager. While trying to retrieve a message, an error occured, preventing successful receipt of the message.

Recommended Action Check ’show context’ command to see if any crash happened. If there is a crash, you may need to collect ’show process blocked’ and ’run attach_process -p pid of crashed process’ output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-ERR_MEM_ALLOC

Failed to [chars] [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-3-ERR_SYSDB_BIND

Failed to bind to SysDB for MIB notifications: [chars]

Explanation SNMP binds to SysDB to receive notifications on the MIB’s behalf. MIBs typically use these notifications as triggers to send out SNMP notifications (e.g. Traps). If SNMP cannot bind to SysDB, these SysDB notifications will not be received, and thus some SNMP notifications may never be generated.

Recommended Action Check ’show context’ command to see if any crash happened and sysdb is in a blocked state. Collect ’show process blocked’ and ’run attach_process -p pid of crashed process’ output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-ERR_SYSDB_GET

Unable to [chars]

Explanation When a show snmp CLI is executed, SNMP agent displays this message when it is not able to retrieve the information. This is likely due to an internal software error.

Recommended Action Check ’show context’ command to see if any crash happened. If there is a crash, you may need to collect ’show process blocked’ and ’run attach_process -p pid of crashed process’ output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-ERR_SYSDB_LIST

Failed to [chars]

Explanation An attempt to read from SysDB failed, the result being that whatever action was being performed cannot be completed by the SNMP agent.

Recommended Action Check ’show context’ command to see if any crash happened and sysdb is in a blocked state. If there is a crash, you may need to collect ’show process blocked’ and ’run attach_process -p pid of crashed process’ output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-GROUP_MSG

Unknown message from [chars]

Explanation snmpd received an unknown message from gsp or from clients.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-3-INIT

Failed to [chars], cannot initialize: [chars]

Explanation The requested operation could not be performed, due to the given reason. This could be due to a low memory condition, or an internal software error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-SNMP-3-INTERNAL

[chars]:[chars]

Explanation General internal failure. This is likely an internal software error.

Recommended Action If there is a crash/deadlock, you may need to collect logs from ’show process blocked’ and ’run attach_process -p pid of crashed process’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-INTERNAL_TUPLE_ERROR

[chars] [chars] [chars] : [chars]

Explanation This is an internal software error. Tuple-Type: The retrieved datatype for the given SysDB tuple does not match the expected datatype. Bad-host: Received a tuple for the snmp-server host CLI command, but could not parse it. Unpack: Failed to decode/unpack the retrieved SysDB tuple value.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-MIBCFGERR

Error in getting MIB config data. [chars], [chars]

Explanation Error in opening cfg directory : The MIB configuration files should be located in the directory ’/ios/mib’. This directory could not be read, for some reason. General Error: A syntax error was encountered while parsing the given MIB configuration file. The MIB referred to by this configuration file will not be loaded. Failed to read MIB Cfg file: This could be due to a low memory condition. Missing config entries: One or more required entries are missing from the given MIB configuration file. The MIB referred to by this configuration file will not be loaded.

Recommended Action Error in opening cfg directory : Ensure that the ’/ios/mib’ directory exists and contains one or more files with a ’.mib’ suffix. Failed to read MIB Cfg file: Ensure that the specified configuration file does exist on the system Missing config entries or General Error: Also provide the contents of the given configuration file. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-NOTIFOID_FAILED

Failed to add sysObjectID to notification view for trapstring: [chars]

Explanation Every trapstring supported by the ’snmp host’ command corresponds to one or more notification OIDs. Each of these notifications will have zero or more varbinds that are carried as payload - each MIB tells snmpd about these varbinds so that a ’notification view’ can be built for them. An extra varbind - sysObjectID - is required to be sent with all v2c notifications. This message indicates that an attempt to register this varbind failed. Sending v2c notifications for the trapstring specified in the error message may fail. You can workaround this by not specifying any trapstring in the ’snmp host’ configuration - this will enable all notifications for that destination.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-SNMP-3-OID_SUBTREE_MISSING

snmp agent is missing part of oid list in the tree

Explanation One of the mibd process has failed to register its oid’s with snmpd. Either due to failure in mibd init or issue in communication channel between snmpd and mibd. This would result in failure of snmpd get or next request on those oids.

Recommended Action It is possible that one of the mibd_* process has crashed or failed to initialize. Check show context for crashes. Collect show tech snmp, follow process of mibds and sysmgr debug logs

Error Message %SNMP-SNMP-3-PERSISTENCE_FILE_LOCATION_GET_ERR

Failed to get location of the persistence file: [chars]

Explanation SNMP agent reads default engineID and engineboots from a persistence file on startup. It fails to find the location of the persistence file. This causes delay or failure in the start up of the snmpd process.

Recommended Action Collect the show logging output, console logs and error message. Collect the show snmp trace output, and contact tac representative with this information.

Error Message %SNMP-SNMP-3-SUBAGT

Failed initialize Sub-Agent:[chars]

Explanation Error indicating that one of the SNMP Sub-Agent could get initialized.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-TARGETNONE

Cannot find notification target [chars]

Explanation A configuration command refers to an SNMP target that has not yet been configured.

Recommended Action You must configure an SNMP target before you can refer to it. Examine your configuration. Ensure that the given target has been configured. If it has not, configure it. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-3-TRANSPORTIO

Failed to [chars] transport [chars]: [chars]

Explanation Failed to communicate with the SNMP transport process. This could be due to a low memory condition, or the fact that there is no SNMP transport process running.

Recommended Action Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-3-TRAPSEND

Failed to send trap to [chars]

Explanation A trap destined for the given address could not be sent. This could be due to a low memory condition. It also might be due to the fact that there is no SNMP transport process running for that transport protocol (e.g. udp_snmpd for SNMP over UDP).

Recommended Action Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-3-TUPLEVALUE

Failed to retrieve tuple [chars]%s: [chars]

Explanation Failed to retrieve the given SysDB tuple for the given reason. This may or may not have a detrimental effect on the behavior of the SNMP agent (depends on which tuple it is).

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-BULKSTATOID_NOT_FOUND

The command [chars] could not be applied at this time because the oid [chars] may be invalid or duplicate

Explanation The snmpd process attempted to load the bulkstat OID, but the OID did not correspond to any known MIB module.

Recommended Action It could be that either - 1. the OID is of the format ’foobar.1’, but the MIB module containing the OID ’foobar’ is not yet loaded on the router. If this is the case, when the MIB is loaded, this command will be automatically applied - there is no need to re-enter it. 2. The MIB module containing the OID ’foobar’ is indeed loaded, but the MIB did not load a translation from ’foobar’ to ’1.3.6.1.x.y.z’ (i.e. there is no translation from the oid-name to the dotted decimal representation for that name). In this case, you can enter the dotted decimal version instead of the name, i.e. ’add 1.3.6.1.x.y.z’ - note that using the dotted decimal version of the name will ALWAYS succeed without a warning message - it is upto the user to make sure the OID entered is valid. 3. The OID ’foobar.1’ contains a typo - please re-enter the command with the correct OID and it should succeed. If the above steps result in repeated warning messages or failure, please contact your customer support representative wit the error message.

Error Message %SNMP-SNMP-4-CONFIGOPEN

Failed to open snmp agent configuration file

Explanation Failed to open snmp agent configuration file, /disk0/config/snmp/snmpd.cnf

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-DEBUGDUP

Duplicate debug registration for the MIB [chars]

Explanation The given MIB attempted to register for MIB debug handling more than once. This is an internal software error. It may not have a detrimental effect on the behavior of the SNMP agent.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-DEBUGFAIL

Failed debug registration for the MIB [chars]

Explanation Failed to initialize support for the command ’debug snmp mib xxx’, where ’xxx’ is the MIB indicated in the error message. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-SNMP-4-ENABLEFAILED

Unable to parse tuple [chars] when trying to enable or disable a trap

Explanation The SysDB tuple was not properly formatted, and hence could not be parsed. This will not degrade system performance, but the user will be unable to enable or disable some traps.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-ENABLENOTSUPPORTED

Unrecognized trap type ([chars]). MIB is not loaded

Explanation The snmp-server enable traps command allowed the user to set the specified traptype, but no callback function was registered to handle the command. This should have no detrimental effect on the system, but the user will not be able to enable/disable the specified trap.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-ENABLETRAPSTWICE

[chars] MIB attempt to register same handler for the snmp enable traps [chars] command twice: handler: [hex]

Explanation The given MIB attempted to register a second handler for the same traptype in the ’snmp enable traps traptype’ command. This should have no detrimental effect on the behavior of the system.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-EXCEEDEDSIZE

The maximum allowed size for enable trap tuple exceeded for [chars] trapstring

Explanation While creating an enable trap tuple we exceeded the limit of maximum allowed size. The snmp enable trap command for this trapstring will not be NVGENed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-INCOMING_QUEUE_FULL

Maximum incoming trap queue size reached, emitting the oldest trap from correlation incoming queue

Explanation SNMP trap correlation incoming queue is full; traps already in the queue is emitted on a FIFO basis to free up room for more incoming traps

Recommended Action No action is required.

Error Message %SNMP-SNMP-4-INIT_WARN

Failed to [chars], cannot initialize: [chars]

Explanation The requested operation could not be performed, due to the given reason. This could be due to a low memory condition, or an internal software error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-SNMP-4-INTERNAL_TRAP_QFULL

[chars]

Explanation SNMP agent recieves trap requests from all the sub agents on a internal queue, then the traps are classified based on several factors and passed on to different set of queues.

Recommended Action It is possible that huge number of traps are generated if traps are enabled for routine or simple events. Collect the show logging output, console logs, error message and trap configuration for review.

Error Message %SNMP-SNMP-4-NOTIFYTWICE

[chars] MIB attempt to register for [chars] notifications again: existing handlers: [hex] [hex]

Explanation The given MIB attempted to register more than once for the given MIB notifications. This should have no detrimental effect on the behavior of the system.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-RESPONSE

Failed to send response to [chars]

Explanation A response destined for the given address could not be sent. This could be due to a low memory condition. It also might be due to the fact that there is no SNMP transport process running for that transport protocol (e.g. udp_snmpd for SNMP over UDP).

Recommended Action Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-4-TARGETINUSE

Notification target [chars] is in use

Explanation An attempt was made to unconfigure an SNMP target, however that target is still in use by one or more other SNMP configuration commands.

Recommended Action You must remove all other configuration commands that refer to this target before you can remove this target configuration. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-TIMER

[chars]: [chars]

Explanation Timer problem; internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-TRAPEMPTY

Found empty trap, destined for [chars]

Explanation A trap destined for the given address was empty. This is an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-USER_NOT_AVAILABLE

User ’[chars]’ will be available only on crypto pie installation

Explanation SNMP user configured with aes and 3des encryption will be available for snmp operations only if crypto pie is installed on the router. Though the user config will be available in the router, user will not be operational.

Recommended Action If snmp user with 3des and aes encrypiton is required for snmp operation then please install crypto pie on the router.

Error Message %SNMP-SNMP-4-VIEWFAIL

Could not create view: [chars]

Explanation Could not create an SNMP view using the ’snmp-server view’ CLI command. Possible causes could be poorly formatted viewnames or oid subtrees.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-VIEWOID_NOT_FOUND

The command [chars] could not be applied at this time because the oid [chars] does not belong to a known MIB module.

Explanation The snmpd process attempted to load the view OID, but the OID did not correspond to any known MIB module.

Recommended Action It could be that either - 1. the OID is of the format ’foobar.1’, but the MIB module containing the OID ’foobar’ is not yet loaded on the router. If this is the case, when the MIB is loaded, this command will be automatically applied - there is no need to re-enter it. 2. The MIB module containing the OID ’foobar’ is indeed loaded, but the MIB did not load a translation from ’foobar’ to ’1.3.6.1.x.y.z’ (i.e. there is no translation from the oid-name to the dotted decimal representation for that name). In this case, you can enter the dotted decimal version instead of the name, i.e. ’snmp-server view viewname 1.3.6.1.x.y.z included’ - note that using the dotted decimal version of the name will ALWAYS succeed without a warning message - it is upto the user to make sure the OID entered is valid. 3. The OID ’foobar.1’ contains a typo - please re-enter the command with the correct OID and it should succeed. If the above steps result in repeated warning messages or failure, please contact your customer support representative wit the error message.

Error Message %SNMP-SNMP-4-WARN_BAG_REG

Failed to register bags with SysDB for providing SNMP statistics and MIB information: [chars]

Explanation Failed to register the bags with SysDB. The access to SNMP statistics and MIB items in /oper/snmp/info through ’sysdbcon’ might not be available. This is likely due to an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-WARN_MEM_ALLOC

Insufficient memory to [chars] [chars]

Explanation Due to a low memory condition we could not enable (or disable) the specified traps or we could not register to receive the specified MIB notifications. Until available memory is increased and the SNMP process is restarted, these notifications will not be generated by the agent.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SNMP-4-WARN_SYSDB_BAG_ENCODE

Failed to encode a bag due to [chars]

Explanation Failed to encode a bag. The access to SNMP statistics and MIB information through ’show snmp’ CLI command might not be available. This is likely due to an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-WARN_SYSDB_EDM_REG

Failed to register as EDM for providing SNMP statistics and MIB information: [chars]

Explanation Failed to register as EDM. The access to SNMP statistics and MIB information through ’show snmp’ CLI command will not be available. This is likely due to an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-4-WARN_SYSDB_NOTIFY

Failed to [chars] [chars]: [chars]

Explanation Failed to register for receipt of the given notifications. This could be due to a low memory condition or an internal software error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-SNMP-7-DEBUGINIT

Failed debug registration for SNMP

Explanation Failed to initialize support for the command ’debug snmp xxx’, where xxx is one of the areas of debug interest within SNMP. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-7-ERR_NOTFOUND

Unable to [chars]

Explanation Did not get data in sysdb, there could be a case where data does not exist. Like, in case of some mibs No. of objects are zero and hence ’sh snmp mib object-name’ will give this warnning.

Recommended Action Check whether this mib contains any object or not. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-7-MIBINSTALL

[chars]

Explanation An error was encountered during installation of a new MIB or deletion of an old MIB. These messages are printed when MIB installation/deletion failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SNMP-7-PERSISTENCE_FILE_MISSING

Persistence file [chars] will be created on initialization, reset snmpEngineBoots to 1

Explanation SNMP agent reads default engineID and engineboots from a persistence file on startup. File is missing, and will be created, reset engineboots to 1

Recommended Action No action is required.

SONETMIB Messages

Error Message %SNMP-SONETMIB-3-BAG

An operation on a bag failed: [chars]

Explanation A problem occurred while encoding or decoding information from a bag.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIB-3-BAG

An operation on a bag failed: [chars]

Explanation A problem occurred while encoding or decoding information from a bag.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIB-3-NOMEM_ERROR

Failed to [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action ’Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.’

Error Message %SNMP-SONETMIB-3-NOMEM_ERROR

Failed to [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action ’Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.’

Error Message %SNMP-SONETMIB-3-SYSDB_ACCESS

Sysdb related error: [chars]

Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIB-3-SYSDB_ACCESS

Sysdb related error: [chars]

Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SONETMIBAPI Messages

Error Message %SNMP-SONETMIBAPI-2-THREAD_CREATE

pthread_create([chars]) failed

Explanation Sonet MIB API had trouble in creating thread.

Recommended Action File a DDTS If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBAPI-3-BAG

An operation on a bag failed: [chars]

Explanation A problem occurred while encoding or decoding information from a bag.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBAPI-3-EVM_CREATE_ERR

Event manager create failed : [chars]

Explanation An internal operation failed. The system will attempt to recover.

Recommended Action Copy the message exactly as it appears, and report it to your technical support representative.

Error Message %SNMP-SONETMIBAPI-3-NOMEM_ERROR

Failed [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action ’Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.’

Error Message %SNMP-SONETMIBAPI-3-SYSDB_ACCESS

Sysdb related error: [chars]

Explanation SonetMIB API had trouble registering/deregistering EDM or binding/unbinding SysDB.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SONETMIBCORE Messages

Error Message %SNMP-SONETMIBCORE-2-THREAD_CREATE

pthread_create([chars]) failed

Explanation Sonet MIB API had trouble in creating thread.

Recommended Action File a DDTS If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBCORE-3-BAG

An operation on a bag failed: [chars]

Explanation A problem occurred while encoding or decoding information from a bag.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBCORE-3-EVM_CREATE_ERR

Event manager create failed : [chars]

Explanation An internal operation failed. The system will attempt to recover.

Recommended Action Copy the message exactly as it appears, and report it to your technical support representative.

Error Message %SNMP-SONETMIBCORE-3-NOMEM_ERROR

Failed [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action ’Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.’

Error Message %SNMP-SONETMIBCORE-3-SYSDB_ACCESS

Sysdb related error: [chars]

Explanation SonetMIB API had trouble registering/deregistering EDM or binding/unbinding SysDB.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBCORE-7-DEBUG

[chars]

Explanation A Debug message

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBCORE-7-DEBUG2

[chars] : [chars]

Explanation A Debug message

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SONETMIBCORE-7-ERROR

[chars] : [chars]

Explanation An internal operation failed. The system will attempt to recover.

Recommended Action Copy the message exactly as it appears, and report it to your technical support representative.

Error Message %SNMP-SONETMIBCORE-7-STATUS

Send SNMP [chars] trap notification to [chars] : [hex]

Explanation A Debug message

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SYSLOGMIB Messages

Error Message %SNMP-SYSLOGMIB-3-NOMEM

Insufficient memory to perform [chars] operation

Explanation No memory in the process.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-SYSLOGMIB-3-PARSEERROR

Failed to parse [chars]

Explanation This is given out if there are problems parsing the encoded tuple from syslogd/sysdb.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SYSLOGMIB-3-SYSDBERROR

Failed to [chars]. Error: [chars]:

Explanation The syslog mib reads the sysdb tuples and gets information about the syslog mib objects. If due to some reason the sysdb error occurs this message is printed out.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-SYSLOGMIB-3-TARGET_CFG_PROBLEM

[chars] : Failed to [chars] target config for [chars] : [chars]

Explanation An internal software error occurred.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

UDPSNMP Messages

Error Message %SNMP-UDPSNMP-3-ERR_MEM_ALLOC

Failed to [chars], due to lack of memory

Explanation The requested operation could not be performed due to a low memory condition.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-UDPSNMP-3-ERR_SYSDB_ACCESS

Failed to [chars] due to sysdb error:[chars]

Explanation udp_snmpd reads the snmp trap Q length and trap timeout from the sysdb. If udp_snmpd is not able to read it then this error is printed. Or is printed when sysdb configuration for trap host does not have valid format. This is an internal error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-UDPSNMP-3-ERR_SYSDB_BIND

Failed to bind to SysDB for [chars]: [chars]

Explanation udp_snmpd binds to SysDB to receive notifications on the trap destinations udp_snmpd typically use these notifications to add trap destination to the trap Q. If udp_snmpd cannot bind to SysDB, these SysDB notifications will not be received, and thus some trap desination will not be added and traps will not be sent to those destinations.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-UDPSNMP-3-ERR_SYSDB_REG

Failed to register for [chars] [chars]: [chars]

Explanation Failed to register for receipt of the given notifications or receipt of the verification event. This could be due to a low memory condition or an internal software error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-UDPSNMP-3-INIT

Failed to [chars], cannot initialize: [chars]

Explanation Initialization failed. This could be due to a low memory condition or an internal software error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-UDPSNMP-3-SYSTEM

Failed to [chars]

Explanation Failed to execute a system call. This could be due to low memory condition or an internal software error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message %SNMP-UDPSNMP-4-AGENTIO_WARN

[chars] [chars]: [chars]

Explanation SNMP-UDP process received a bad Message or failed to send a message to Agent. This may be due to a invalid message number or an internal software error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-UDPSNMP-4-NOVRF

Failed to find VRF details for [dec]/[chars]

Explanation Failed to find VRF related information that is required to send an SNMP PDU. This could be due to an internal software error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-UDPSNMP-4-SYSMGR_INFORM

Failed to inform SysMgr on SNMP-UDP initialization, [chars]

Explanation Failed to inform SysMgr on end of initialization of UDP transport module for SNMP. This could be due to a block in snmpd initialization. If snmpd process does not come to normal execution even after some time need to take the recommended action.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Take the ’show processes blocked’ and ’run attach_process -p snmpd-pid’

Error Message %SNMP-UDPSNMP-7-INTERNAL_ERROR

Failed to [chars]: [chars]

Explanation Failed to initialize a functionality for snmp - like debugging, setup event manager for notification timer. Or failed to send PDU since the outgoing PDU is greater than the configured maximum PDU size, the PDU will be dropped. This could be due to an internal software error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

UTIL Messages

Error Message %SNMP-UTIL-3-NOINIT

SNMP Utilities Library not properly initialized

Explanation The SNMP Utilities library was not properly initialized by the SNMP agent. This is an internal software error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

VLANIFMIB Messages

Error Message %SNMP-VLANIFMIB-4-BAG

Bag encode/decode Error : [chars]

Explanation The VLAN Interface table relationship MIB encountered an error while encoding / decoding some data. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-VLANIFMIB-4-GEN

Failed to [chars]

Explanation The VLAN Interface table relationship MIB encountered an internal error during initialisation. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-VLANIFMIB-4-MEMORY

Failed to [chars]

Explanation The VLAN Interface table relationship MIB was unable to allocate sufficient memory to complete an operation. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %SNMP-VLANIFMIB-4-MIBLIB

Failed to [chars]

Explanation The VLAN Interface table relationship MIB encountered an internal error. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %SNMP-VLANIFMIB-4-SYSDB_ACCESS

SysDB failed to [chars]

Explanation The VLAN Interface table relationship MIB encountered an error while connecting to, or accessing data within the System Database. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.