Cisco IOS XR Interface and Hardware Component Debug Command Reference, Release 3.5
Packet-over-SONET User Interface and SONET Layer 1 Debug Commands on Cisco IOS XR Software
Downloads: This chapterpdf (PDF - 559.0KB) The complete bookPDF (PDF - 2.19MB) | Feedback

Packet-over-SONET User Interface and SONET Layer 1 Debug Commands on Cisco IOS XR Software

Table Of Contents

Packet-over-SONET User Interface and SONET Layer 1 Debug Commands on Cisco IOS XR Software

debug pos all

debug pos events

debug pos framer

debug pos im

debug pos info

debug pos mapping

debug pos periodic

debug pos sysdb

debug pos trace

debug sonet all

debug sonet aps

debug sonet errors

debug sonet events

debug sonet framer

debug sonet im

debug sonet info

debug sonet mapping

debug sonet periodic

debug sonet sysdb


Packet-over-SONET User Interface and SONET Layer 1 Debug Commands on Cisco IOS XR Software


This chapter describes the Cisco IOS XR commands used to debug Packet-over-SONET (POS).

debug pos all

To debug information for all POS, use the debug pos all command in EXEC mode. To disable debugging, use the no form of this command.

debug pos all [location node-id]

no debug pos all [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to display debug information for all POS with the debug pos all command:

RP/0/RP0/CPU0:router# debug pos all location 0/2/CPU0
 
   
LC/0/2/CPU0:Jun 27 16:40:51.465 : plim_16p_oc48[190]: pos_port_get_hw_stats, data @ 
48249c78
LC/0/2/CPU0:Jun 27 16:40:51.465 : plim_16p_oc48[190]: --> 
pos_find_owned_im_node_data_by_ifhtype, 251
LC/0/2/CPU0:Jun 27 16:40:51.465 : plim_16p_oc48[190]:     searching IM data @ 48
24c034
LC/0/2/CPU0:Jun 27 16:40:51.465 : plim_16p_oc48[190]:     searching IM data @ 48
2558c8
LC/0/2/CPU0:Jun 27 16:40:51.466 : plim_16p_oc48[190]: --> pos_get_port_data_by_im_data, 
366
LC/0/2/CPU0:Jun 27 16:40:51.466 : plim_16p_oc48[190]: pos_get_port_data_by_im_data: type 
19 context 482555d4
LC/0/2/CPU0:Jun 27 16:40:51.466 : plim_16p_oc48[190]: pos_get_port_data_by_ifhandle(), 
418: mapped ifhandle: @012800c0 --> pos_port_st: @482555d4
LC/0/2/CPU0:Jun 27 16:40:51.466 : plim_16p_oc48[190]: --> pos_get_stats, 302: port 1
 
   

Related Commands

Command
Description

debug pos events

Debugs information for POS events.

debug pos framer

Debugs information for the POS framer.

debug pos info

Debugs information for the generic POS informative events.

debug pos mapping

Debugs information to map the hardware for POS.

debug pos periodic

Debugs information to periodically process the POS hardware.

debug pos trace

Debugs information to trace (verbose) POS.


debug pos events

To debug information for POS events, use the debug pos events command in EXEC mode. To disable debugging, use the no form of this command.

debug pos events [location node-id]

no debug pos events [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information for POS events with the debug pos events command:

RP/0/RP0/CPU0:router# debug pos events location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos all

Debugs information for all POS.

debug pos framer

Debugs information for the POS framer.

debug pos info

Debugs information for the generic POS informative events.

debug pos mapping

Debugs information to map the hardware for POS.

debug pos periodic

Debugs information to periodically process the POS hardware.

debug pos trace

Debugs information to trace (verbose) POS.


debug pos framer

To debug information for the POS framer, use the debug pos framer command in EXEC mode. To disable debugging, use the no form of this command.

debug pos framer [all | events | info | operations | periodic | trace] [location node-id]

no debug pos framer [all | events | info | operations | periodic | trace] [location node-id]

Syntax Description

all

(Optional) Specifies debug information for all POS framers.

events

(Optional) Specifies debug information for the generic hardware events for the POS framer.

info

(Optional) Specifies debug information for the generic informative messages for the POS framer.

operations

(Optional) Specifies debug information for the generic hardware operations for the POS framer.

periodic

(Optional) Specifies debug information to periodically process the generic POS framer.

trace

(Optional) Specifies debug information to trace (verbose) the POS framer.

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information for the generic hardware events for the POS framer with the debug pos framer command:

RP/0/RP0/CPU0:router# debug pos framer events location 0/0/CPU0
RP/0/RP0/CPU0:router#

Related Commands

Command
Description

debug pos all

Debugs information for all POS.

debug pos events

Debugs information for POS events.

debug pos info

Debugs information for the generic POS informative events.

debug pos mapping

Debugs information to map the hardware for POS.

debug pos periodic

Debugs information to periodically process the POS hardware.

debug pos trace

Debugs information to trace (verbose) POS.


debug pos im

To debug information for the POS interface manager, use the debug pos im command in EXEC mode. To disable debugging, use the no form of this command.

debug pos im [location node-id]

no debug pos im [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information for the PoS interface manager with the debug pos im command:

RP/0/RP0/CPU0:router# debug pos im location 0/0/CPU0 
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos all

Debugs information for all PoS.

debug sonet im

Debugs information for the SONET interface manager.


debug pos info

To debug information for the generic PoS informative events, use the debug pos info command in EXEC mode. To disable debugging, use the no form of this command.

debug pos info [location node-id]

no debug pos info [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information for the generic PoS informative events with the debug pos info command:

RP/0/RP0/CPU0:router# debug pos info location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos all

Debugs information for all PoS.

debug pos events

Debugs information for PoS events.

debug pos framer

Debugs information for the PoS framer.

debug pos mapping

Debugs information to map the hardware for PoS.

debug pos periodic

Debugs information to periodically process the PoS hardware.

debug pos trace

Debugs information to trace (verbose) PoS.


debug pos mapping

To debug information to map the hardware for PoS, use the debug pos mapping command in EXEC mode. To disable debugging, use the no form of this command.

debug pos mapping [location node-id]

no debug pos mapping [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information to map the hardware for PoS with the debug pos mapping command:

RP/0/RP0/CPU0:router# debug pos mapping location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos all

Debugs information for all PoS.

debug pos events

Debugs information for PoS events.

debug pos framer

Debugs information for the PoS framer.

debug pos info

Debugs information for the generic PoS informative events.

debug pos periodic

Debugs information to periodically process the PoS hardware.

debug pos trace

Debugs information to trace (verbose) PoS.

debug sonet mapping

Debugs information to map SONET hardware.


debug pos periodic

To debug information to periodically process the PoS hardware, use the debug pos periodic command in EXEC mode. To disable debugging, use the no form of this command.

debug pos periodic [location node-id]

no debug pos periodic [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information to periodically process the PoS hardware with the debug pos periodic command:

RP/0/RP0/CPU0:router# debug pos periodic location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos all

Debugs information for all PoS.

debug pos events

Debugs information for PoS events.

debug pos framer

Debugs information for the PoS framer.

debug pos info

Debugs information for the generic PoS informative events.

debug pos mapping

Debugs information to map the hardware for PoS.

debug pos trace

Debugs information to trace (verbose) PoS.


debug pos sysdb

To debug information for the POS system database, use the debug pos sysdb command in EXEC mode. To disable debugging, use the no form of this command.

debug pos sysdb [location node-id]

no debug pos sysdb [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information for the PoS system database with the debug pos sysdb command:

RP/0/RP0/CPU0:router# debug pos sysdb location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug sonet sysdb

Debugs information for the SONET system database.


debug pos trace

To debug information to trace (verbose) PoS, use the debug pos trace command in EXEC mode. To disable debugging, use the no form of this command.

debug pos trace [location node-id]

no debug pos trace [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

pos-dpt

read


Examples

The following example shows how to enable debugging information to trace (verbose) PoS with the debug pos trace command:

RP/0/RP0/CPU0:router# debug pos trace location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos all

Debugs information for all PoS.

debug pos events

Debugs information for PoS events.

debug pos framer

Debugs information for the PoS framer.

debug pos info

Debugs information for the generic PoS informative events.

debug pos mapping

Debugs information to map the hardware for PoS.

debug pos periodic

Debugs information to periodically process the PoS hardware.


debug sonet all

To debug information for all but periodic SONET, use the debug sonet all command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet all [location node-id]

no debug sonet all [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to display debugging information for SONET with the debug sonet all command:

RP/0/RP0/CPU0:router# debug sonet all location 0/0/CPU0
 
   
LC/0/0/CPU0:Jun 28 13:02:04.957 : vpa_1p_oc192[247]: sonet_hw_c2_state_changed:
SonetPath0/0/1/0 state=3
LC/0/0/CPU0:Jun 28 13:02:05.393 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/1 state=3
LC/0/0/CPU0:Jun 28 13:02:05.393 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/2 state=3
LC/0/0/CPU0:Jun 28 13:02:05.393 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/3 state=3
LC/0/0/CPU0:Jun 28 13:02:05.958 : vpa_1p_oc192[247]: sonet_hw_c2_state_changed:
SonetPath0/0/1/0 state=3
LC/0/0/CPU0:Jun 28 13:02:06.394 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/1 state=3
LC/0/0/CPU0:Jun 28 13:02:06.394 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/2 state=3
LC/0/0/CPU0:Jun 28 13:02:06.394 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/3 state=3
LC/0/0/CPU0:Jun 28 13:02:06.959 : vpa_1p_oc192[247]: sonet_hw_c2_state_changed:
SonetPath0/0/1/0 state=3
LC/0/0/CPU0:Jun 28 13:02:07.395 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/1 state=3
LC/0/0/CPU0:Jun 28 13:02:07.395 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/2 state=3
LC/0/0/CPU0:Jun 28 13:02:07.395 : spa_4p_oc3[214]: sonet_hw_c2_state_changed: 
SonetPath0/0/5/3 state=3
 
   

Related Commands

Command
Description

debug sonet aps

Debugs information for the SONET automatic protection switching (APS).

debug sonet errors

Debugs SONET errors.

debug sonet events

Debugs information for SONET events.

debug sonet info

Debugs generic SONET information.

debug sonet sysdb

Debugs information for the SONET system database.


debug sonet aps

To debug information for the SONET APS, use the debug sonet aps command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet aps [all | errors | events | info | pgp | sysdb | trace | wp-comm] [location node-id]

no debug sonet aps [all | errors | events | info | pgp | sysdb | trace | wp-comm] [location node-id]

Syntax Description

all

(Optional) Specifies debug information for all SONET APS except PGP.

errors

(Optional) Specifies debug information for nonfatal errors for APS.

events

(Optional) Specifies debug information for APS events.

info

(Optional) Specifies debug information for APS.

location

(Optional) Specifies a location.

pgp

(Optional) Specifies debug information for APS PGP communication.

sysdb

(Optional) Specifies debug information for APS system database interaction.

trace

(Optional) Specifies debug information for trace APS in verbose mode.

wp-comm

(Optional) Specifies debug information for APS internal working-protect communication.

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for the SONET APS with the debug sonet aps command:

RP/0/RP0/CPU0:router# debug sonet aps info location 0/0/CPU0
RP/0/RP0/CPU0:router#

Related Commands

Command
Description

debug sonet all

Debugs information for all but periodic SONET.

debug sonet errors

Debugs SONET errors.

debug sonet events

Debugs information for SONET events.

debug sonet info

Debugs generic SONET information.

debug sonet sysdb

Debugs information for the SONET system database.


debug sonet errors

To debug SONET errors, use the debug sonet errors command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet errors [location node-id]

no debug sonet errors [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for SONET errors with the debug sonet errors command:

RP/0/RP0/CPU0:router# debug sonet errors location 0/0/CPU0
RP/0/RP0/CPU0:router#

Related Commands

Command
Description

debug sonet all

Debugs information for all but periodic SONET.

debug sonet aps

Debugs information for the SONET APS.

debug sonet events

Debugs information for SONET events.

debug sonet info

Debugs generic SONET information.

debug sonet sysdb

Debugs information for the SONET system database.


debug sonet events

To debug information for SONET events, use the debug sonet events command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet events [location node-id]

no debug sonet events [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for SONET events with the debug sonet events command:

RP/0/RP0/CPU0:router# debug sonet events location 0/0/CPU0
RP/0/RP0/CPU0:router#

Related Commands

Command
Description

debug sonet all

Debugs information for all but periodic SONET.

debug sonet aps

Debugs information for the SONET APS.

debug sonet errors

Debugs SONET errors.

debug sonet info

Debugs generic SONET information.

debug sonet sysdb

Debugs information for the SONET system database.


debug sonet framer

To debug information for the SONET framer, use the debug sonet framer command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet framer {all | events | info | operation | periodic} [location node-id]

no debug sonet framer {all | events | info | operation | periodic} [location node-id]

Syntax Description

all

Specifies debug information for all (but periodic) SONET framer.

events

Specifies debug information for the generic SONET framer.

info

Specifies debug information for the generic SONET framer.

operation

Specifies debug information for the generic SONET framer.

periodic

Specifies debug information for the generic SONET framer.

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for the generic SONET framer with the debug sonet framer command:

RP/0/RP0/CPU0:router# debug sonet framer events location 0/0/CPU0
RP/0/RP0/CPU0:router#

Related Commands

Command
Description

debug sonet all

Debugs information for all but periodic SONET.

debug sonet events

Debugs information for SONET events.

debug sonet info

Debugs generic SONET information.


debug sonet im

To debug information for the SONET interface manager, use the debug sonet im command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet im [location node-id]

no debug sonet im [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for the SONET interface manager with the debug sonet im command:

RP/0/RP0/CPU0:router# debug sonet im location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos im

Debugs information for the POS interface manager.

debug sonet all

Debugs information for all but periodic SONET.


debug sonet info

To debug generic SONET information, use the debug sonet info command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet info [location node-id]

no debug sonet info [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for generic SONET information with the debug sonet info command:

RP/0/RP0/CPU0:router# debug sonet info location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Syntax Description

Command
Description

debug sonet all

Debugs information for all but periodic SONET.

debug sonet aps

Debugs information for the SONET APS.

debug sonet errors

Debugs SONET errors.

debug sonet events

Debugs information for SONET events.

debug sonet sysdb

Debugs information for the SONET system database.


debug sonet mapping

To debug information to map SONET hardware, use the debug sonet mapping command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet mapping [location node-id]

no debug sonet mapping [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information to map SONET hardware with the debug sonet mapping command:

RP/0/RP0/CPU0:router# debug sonet mapping location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos mapping

Debugs information to map the hardware for PoS.

debug sonet all

Debugs information for all but periodic SONET.

debug sonet aps

Debugs information for the SONET APS.

debug sonet events

Debugs information for SONET events.

debug sonet framer

Debugs information for the SONET framer.

debug sonet info

Debugs generic SONET information.

debug sonet periodic

Debugs SONET information for periodic events.


debug sonet periodic

To debug SONET information for periodic events, use the debug sonet periodic command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet periodic [location node-id]

no debug sonet periodic [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging SONET information for periodic events with the debug sonet periodic command:

RP/0/RP0/CPU0:router# debug sonet periodic location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug pos periodic

Debugs information to periodically process the PoS hardware.

debug sonet all

Debugs information for all but periodic SONET.

debug sonet aps

Debugs information for the SONET APS.

debug sonet events

Debugs information for SONET events.

debug sonet framer

Debugs information for the SONET framer.

debug sonet info

Debugs generic SONET information.

debug sonet mapping

Debugs information to map SONET hardware.


debug sonet sysdb

To debug information for the SONET system database, use the debug sonet sysdb command in EXEC mode. To disable debugging, use the no form of this command.

debug sonet sysdb [location node-id]

no debug sonet sysdb [location node-id]

Syntax Description

location node-id

(Optional) Specifies debug information to enable a specified location (for example, 0/0/CPU0). The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is the location of the current, active route processor (RP).

Command Modes

EXEC

Command History

Release
Modification

Release 3.0

This command was introduced on the Cisco CRS-1.

Release 3.2

No modification.

Release 3.3.0

No modification.

Release 3.4.0

This command was supported on the Cisco XR 12000 Series Router.

Release 3.5.0

No modification.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Debugging output is assigned high priority in the CPU process and, therefore, can affect system performance. For more information about the impact on system performance when using debug commands, refer to Using Debug Commands on Cisco IOS XR Software.

Task ID

Task ID
Operations

sonet-sdh

read, write


Examples

The following example shows how to enable debugging information for the SONET system database with the debug sonet sysdb command:

RP/0/RP0/CPU0:router# debug sonet sysdb location 0/0/CPU0
RP/0/RP0/CPU0:router#
 
   

Related Commands

Command
Description

debug sonet all

Debugs information for all but periodic SONET.

debug sonet aps

Debugs information for the SONET APS.

debug sonet errors

Debugs SONET errors.

debug sonet events

Debugs information for SONET events.

debug sonet info

Debugs generic SONET information.