Cisco IOS XR System Error Message Reference Guide, Release 3.5
Simple Network Management Protocol (SNMP) Messages
Downloads: This chapterpdf (PDF - 502.0KB) The complete bookPDF (PDF - 18.83MB) | Feedback

Simple Network Management Protocol (SNMP) Messages

Table Of Contents

Simple Network Management Protocol (SNMP) Messages

ATM_MIB Messages

ATMSNMP Messages

BULKFILEMIB Messages

CISCOBGPPAMIB Messages

CISCOPROCESSMIB Messages

CISCOSYSTEMMIB Messages

COPYMIB Messages

CSCMIB Messages

ETHERMIB Messages

FTPCLIENTMIB Messages

HSRPMIB Messages

IFINDEX_PROVIDER Messages

IFMIB Messages

IPMIB Messages

LIBSNMP Messages

MIB Messages

NLMMIB Messages

PINGMIB Messages

QOSMIB Messages

SNMP Messages

SONETMIB Messages

SONETMIBAPI Messages

SONETMIBCORE Messages

SYSLOGMIB Messages

UDPSNMP Messages

UTIL Messages

VLANIFMIB Messages


Simple Network Management Protocol (SNMP) Messages


This section contains all Simple Network Management Protocol related System Error Messages, such as BGP, MIB, CONFIG MIB, SNMP agent, and so forth. MIB location does not matter. The following facility codes are represented in this module:

ATM_MIB Messages

ATMSNMP Messages

BULKFILEMIB Messages

CISCOBGPPAMIB Messages

CISCOPROCESSMIB Messages

CISCOSYSTEMMIB Messages

COPYMIB Messages

CSCMIB Messages

ETHERMIB Messages

FTPCLIENTMIB Messages

HSRPMIB Messages

IFINDEX_PROVIDER Messages

IFMIB Messages

IPMIB Messages

LIBSNMP Messages

MIB Messages

NLMMIB Messages

PINGMIB Messages

QOSMIB Messages

SNMP Messages

SONETMIB Messages

SONETMIBAPI Messages

SONETMIBCORE Messages

SYSLOGMIB Messages

UDPSNMP Messages

UTIL Messages

VLANIFMIB Messages

ATM_MIB Messages

Error Message     
 
    
    
   

%SNMP-ATM_MIB-3-INIT_ERR ATM MIB support initialization failed ([chars]%s)

Explanation    An error occurred while initializing ATM MIB support in snmpd process. If this occurred during process startup, then the process may be restarted.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ATMSNMP Messages

Error Message     
 
    
    
   

%SNMP-ATMSNMP-3-IFMGR ATM SNMP: [chars]: [chars]: [dec]: [dec]

Explanation    A high severity error is encountered.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-ATMSNMP-3-info ATM SNMP: [chars]

Explanation    debug msg

Recommended Action    None

Error Message     
 
    
    
   

%SNMP-ATMSNMP-3-SYSDB ATM SNMP: [chars]: [chars]: [dec]

Explanation    This message indicates the ATM SNMP library fails to perform a SYSDB operation. *DDTS*

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

BULKFILEMIB Messages

Error Message     
 
    
    
   

%SNMP-BULKFILEMIB-3-ERR_MEM_ALLOC Insufficient memory to perform [chars] operation

Explanation    No memory in the process.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-BULKFILEMIB-3-ERR_THREAD_CREATE Could not create a bulk file processing thread

Explanation    There are no resources available to create a bulk file processing thread

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CISCOBGPPAMIB Messages

Error Message     
 
    
    
   

%SNMP-CISCOBGPPAMIB-3-ERR_MEM_ALLOC Failed to get memory for [chars]

Explanation    Memory unavailable

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

CISCOPROCESSMIB Messages

Error Message     
 
    
    
   

%SNMP-CISCOPROCESSMIB-3-ERR_MEM_ALLOC Unable to allocate memory for process name

Explanation    The MIB had trouble allocating memory for process name'

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

CISCOSYSTEMMIB Messages

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-3-CLOCK Clock operation Error: [chars]

Explanation    The MIB had trouble in spawning a process.

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-3-EVENT_ASYNC_ALLOC Failed to allocate asynchronous event: [chars]

Explanation    An internal software error occurred.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-3-SPAWN Spawn Error: [chars]

Explanation    The MIB had trouble in spawning a process.

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-3-SYSDB_ACCESS Sysdb related error: [chars]

Explanation    The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-3-TARGET_CFG_PROBLEM [chars] : Failed to [chars] target config for [chars] : [chars]

Explanation    An internal software error occurred.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-3-TIMER Timer Error: [chars]

Explanation    Timer error

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%SNMP-CISCOSYSTEMMIB-7-CREATE_EVM Could not create event manager for [chars] ([chars])

Explanation    Attempt to create an event manager fails for some reason.

Recommended Action    Use the status to determine the reason.

COPYMIB Messages

Error Message     
 
    
    
   

%SNMP-COPYMIB-3-ENTRYNONE Entry for id [dec] doesn't exist.

Explanation    An attempt to remove an entry from a queue was made, but the entry was not found.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-COPYMIB-3-ERR_MEM_ALLOC Insufficient memory to [chars]

Explanation    No memory to perform edm or bag operations.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CSCMIB Messages

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-CSC_ASSERT Invalid codepath encountered - exitting.

Explanation    An invalid codepath has been encountered - the process is exitting and restarting.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-CSC_BAG The MIB was unable to marshall or unmarshall a set of data, error: [chars]

Explanation    This may be due to invalid data being sent by the agent or request, or due to an error in the data-marshalling infrastructure. The current request cannot be completed. Check the request and try again.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-CSC_OCTETSTRING Failed to convert an SNMP supplied OctetString to a string.

Explanation    An illegal string was passed in to the MIB by the agent. The current request cannot be completed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-CSC_SNMP The SNMP request did not specify an index.

Explanation    The SNMP management station tried a set request without specifying a request index. Check the request and try again.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-INVALID_ARG Internal error occurred: [chars]

Explanation    The MIB has reached an expected state, and will not be able to service the current request.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-NOMEM Could not allocate memory

Explanation    The MIB has failed to aquire the required amount of memory.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-SYSDB_ACCESS The MIB was unable to access the system database, error: [chars]

Explanation    The MIB was unable to read to or write from the system database, so will be unable to provide some requested MIB data.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-CSCMIB-7-SYSDB_BIND The MIB was unable to connect to the system database, error: [chars]

Explanation    The MIB was unable to connect to the system database, so will be unable to provide the MIB data. This may be because the communications infrastructure is not yet up.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ETHERMIB Messages

Error Message     
 
    
    
   

%SNMP-ETHERMIB-4-BAG An operation on a bag failed: [chars]

Explanation    The Ether MIB encountered an error while encoding / decoding some data. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-ETHERMIB-4-SYSDB_ACCESS Sysdb related error: [chars]

Explanation    The Ether MIB encountered an error while connecting to, or accessing data within the System Database. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FTPCLIENTMIB Messages

Error Message     
 
    
    
   

%SNMP-FTPCLIENTMIB-3-NOMEM Insufficient memory to perform [chars] operation

Explanation    No memory in the process.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-FTPCLIENTMIB-3-NOTHREADCREATE Could not create a FTP request processing thread

Explanation    There are no resources available to create a FTP request processing thread

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

HSRPMIB Messages

Error Message     
 
    
    
   

%SNMP-HSRPMIB-3-ERR_CONN The HSRP MIB could not connect to the HSRP process. ([chars])

Explanation    The HSRP MIB was unable to create a SysDB connection to the HSRP process for the purpose of retrieving management information.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-HSRPMIB-4-WARN_DEBUG Failed to register HSRP MIB debug control: [chars]

Explanation    During initialisation of the HSRP MIB, it was not possible to register to be notified of changes to the debugging state. The MIB will continue to function, but it will not be possible to turn on debugging for the MIB.

Recommended Action    If debugging is essential, then restart SNMP. This will reinitialize the HSRP MIB. If the problem persists, do the following. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-HSRPMIB-4-WARN_NOTIFY Failed to register for notification of state changes. ([chars])

Explanation    During initialisation of the HSRP MIB, it was not possible to register to be notified of changes in active state of an HSRP group. The MIB will continue to function, but no traps will be generated for the cHsrpStateChange notification.

Recommended Action    Restart SNMP. This will re-initialize the HSRP MIB. If the problem persists, do the following. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-HSRPMIB-4-WARN_OID Failed to construct OID in trap generation. ([dec])

Explanation    An OID (object identifier) string failed to be constructed during trap generation. The trap for a cHsrpStateChange notification did not get sent.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

IFINDEX_PROVIDER Messages

Error Message     
 
    
    
   

%SNMP-IFINDEX_PROVIDER-3-IFNAME_TO_INDEX Failed to [chars] for [chars]: [chars]

Explanation    Failed to get the ifindex value for the given interface name

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-IFINDEX_PROVIDER-3-SERVER_ERROR [chars] error during [chars]: [chars]

Explanation    An error occurred while communicating with one of the servers

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-IFINDEX_PROVIDER-7-LTRACE_INIT_ERROR '[chars]' error during intialization of LW tracing for ifindex provider

Explanation    An error occured while initializing LW tracing for ifindex provider library.

Recommended Action    No action is required.

IFMIB Messages

Error Message     
 
    
    
   

%SNMP-IFMIB-3-ERR_MEM_ALLOC Failed to [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'

IPMIB Messages

Error Message     
 
    
    
   

%SNMP-IPMIB-3-BAG An operation on a bag failed: [chars]

Explanation    A problem occurred while encoding or decoding information from a bag.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-IPMIB-3-SYSDB_ACCESS Operation [chars] failed, error [chars]

Explanation    The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

LIBSNMP Messages

Error Message     
 
    
    
   

%SNMP-LIBSNMP-3-NOMEM_FOR_INIT snmpd is being shut down due to lack of memory required for initialization. Try restarting snmpd after freeing some memory

Explanation    Not enough memory was available for snmpd to set up its internal data structures.

Recommended Action    Try stopping some running processes, or wait awhile before restarting snmpd. If the problem persists after several tries, please contact your customer support representative.

MIB Messages

Error Message     
 
    
    
   

%SNMP-MIB-3-BADTRANSPORT Attempt to [chars] unknown transport type: [dec]

Explanation    Attempted to perform the indicated operation on an unknown transport type. This is an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-MIB-3-NOINIT MIB Library not properly initialized

Explanation    The MIB library was not properly initialized by the SNMP agent. This is an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-MIB-3-SYSUPTIME Failed to retrieve sysUpTime: [chars]

Explanation    Failed to read the system clock, and thus determine what sysUpTime is. The result is that sysUpTime will latch at its last known value.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

NLMMIB Messages

Error Message     
 
    
    
   

%SNMP-NLMMIB-3-ERR_MEM_ALLOC Failed to [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'

PINGMIB Messages

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-BADID Server received [chars] request with no valid id

Explanation    Bad ID error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-BAG Bag encode/decode Error : [chars]

Explanation    Error bag encoding/decoding

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-ENTRYNONE Entry for id [dec] doesn't exist

Explanation    Entry for id not found

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-EVENT_BLOCK event block call failed: [chars]

Explanation    Event block call failed

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-INIT Failed to [chars], cannot initialize: [chars]

Explanation    initialization failed error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-MSGFAIL SysDB failed to process incoming message: [chars]

Explanation    Sysdb error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-MUTEX_INIT Failed to init pthread mutex: [chars]

Explanation    Failed to init pthread mutex

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-NOMEM Insufficient memory to perform [chars] operation

Explanation    Out of memory error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-NOTHREADCREATE Could not create a PING request processing thread

Explanation    There are no resources available to create a PING request processing thread

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-PTHREAD_COND_INIT Pthread cond wait call failed: [chars]

Explanation    pthread cond wait call failed

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-SYSDB_ACCESS SysDB failed to process incoming message : [chars]

Explanation    Sysdb Err

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-SYSMGR_PROC_READY Failed to notify sysmgr the completion of initialization: [chars]

Explanation    Failed to notify sysmgr the completion of initialization

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-TIMER Failed to create [chars] timer

Explanation    Timer error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-TIMERNOMEM Insufficient memory to create timer for entry [dec]

Explanation    Insufficient memory to create timer for entry error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-TIMERNONE Failed to find timer for entry id [dec]

Explanation    Failed to find timer for entry

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-TRAPOID Failed to create trap OID for [chars]

Explanation    Failed to create trap OID error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-3-UNKNOWNMSG Received unknown event type: [dec]

Explanation    Received unknown event type error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-PINGMIB-7-DEBUG_REGISTER debug register call failed: [chars]

Explanation    debug register call failed. No action needed. System will recover by itself.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

QOSMIB Messages

Error Message     
 
    
    
   

%SNMP-QOSMIB-3-ERR_MEM_ALLOC Insufficient Memory to perform [chars] operation

Explanation    The MIB had trouble allocating memory.

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%SNMP-QOSMIB-3-ERR_NO_ENT Entry for [chars] not found in [chars] or insufficient memory

Explanation    The particular entry was not found in the list or MIB had trouble allocating memory.

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

SNMP Messages

Error Message     
 
    
    
   

%SNMP-SNMP-3-CONFIGFAIL Failed to [chars] [chars]: [chars]

Explanation    Failed to perform the indicated configuration operation. This could be due to a low memory condition, an unsane configuration, or an internal software error. Failed in Host config: Received a good tuple for the snmp-server host CLI command, but could not configure it. This is likely due to lack of memory, which may be a transient condition, or may be due to SNMP supporting too many MIBS with large amounts of data. Try this command again after a few minutes. If it continues to fail, you may wish to undo some SNMP configurations and then retry the command.

Recommended Action    Examine the configuration and ensure that it is sane. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *SH_CMD config*

Error Message     
 
    
    
   

%SNMP-SNMP-3-DATASIZE Data size exceeded for [chars]. Length of data is [dec](max length is [dec])

Explanation    The maximum size of the data has been exceeded. This could be due to user configuration or internal error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_DLL_LOAD Failed to load [chars]: [chars]

Explanation    Failed to load the given MIB, for the given reason. This could be due to a low memory condition.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_DLL_UNKNOWN Failed to map [chars] to an address: [chars]

Explanation    An attempt to map a MIB DLL symbolic name to an address failed. This MIB will be unloaded. This could be due to a corrupted MIB configuration file, a corrupted DLL, or a MIB configuration file that is out-of-sync with its corresponding MIB DLL.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Also provide a copy of the MIB DLL and its associated MIB configuration file.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_EVM_EVENT_BLOCK Received error from event_wait: [chars]

Explanation    SNMP receives messages from an event manager. While trying to retrieve a message, an error occured, preventing successful receipt of the message.

Recommended Action    Check 'show context' command to see if any crash happened . If there is a crash, you may need to collect 'show process blocked' and 'run attach_process -p ' output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_MEM_ALLOC Failed to [chars] [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_SYSDB_BIND Failed to bind to SysDB for MIB notifications: [chars]

Explanation    SNMP binds to SysDB to receive notifications on the MIB's behalf. MIBs typically use these notifications as triggers to send out SNMP notifications (e.g. Traps). If SNMP cannot bind to SysDB, these SysDB notifications will not be received, and thus some SNMP notifications may never be generated.

Recommended Action    Check 'show context' command to see if any crash happened and sysdb is in a blocked state. Collect 'show process blocked' and 'run attach_process -p ' output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_SYSDB_GET Unable to [chars]

Explanation    When a show snmp CLI is executed, SNMP agent displays this message when it is not able to retrieve the information. This is likely due to an internal software error.

Recommended Action    Check 'show context' command to see if any crash happened . If there is a crash, you may need to collect 'show process blocked' and 'run attach_process -p ' output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-ERR_SYSDB_LIST Failed to [chars]

Explanation    An attempt to read from SysDB failed, the result being that whatever action was being performed cannot be completed by the SNMP agent.

Recommended Action    Check 'show context' command to see if any crash happened and sysdb is in a blocked state. If there is a crash, you may need to collect 'show process blocked' and 'run attach_process -p ' output. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-INIT Failed to [chars], cannot initialize: [chars]

Explanation    The requested operation could not be performed, due to the given reason. This could be due to a low memory condition, or an internal software error.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-SNMP-3-INTERNAL [chars]:[chars]

Explanation    General internal failure. This is likely an internal software error.

Recommended Action    If there is a crash/deadlock, you may need to collect logs from 'show process blocked' and 'run attach_process -p ' Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-INTERNAL_TUPLE_ERROR [chars] [chars] [chars] : [chars]

Explanation    This is an internal software error. Tuple-Type: The retrieved datatype for the given SysDB tuple does not match the expected datatype. Bad-host: Received a tuple for the snmp-server host CLI command, but could not parse it. Unpack: Failed to decode/unpack the retrieved SysDB tuple value.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-MIBCFGERR Error in getting MIB config data. [chars], [chars]

Explanation    Error in opening cfg directory : The MIB configuration files should be located in the directory '/ios/mib'. This directory could not be read, for some reason. General Error: A syntax error was encountered while parsing the given MIB configuration file. The MIB referred to by this configuration file will not be loaded. Failed to read MIB Cfg file: This could be due to a low memory condition. Missing config entries: One or more required entries are missing from the given MIB configuration file. The MIB referred to by this configuration file will not be loaded.

Recommended Action    Error in opening cfg directory : Ensure that the '/ios/mib' directory exists and contains one or more files with a '.mib' suffix. Failed to read MIB Cfg file: Ensure that the specified configuration file does exist on the system Missing config entries or General Error: Also provide the contents of the given configuration file. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-NOTIFOID_FAILED Failed to add sysObjectID to notification view for trapstring: [chars]

Explanation    Every trapstring supported by the 'snmp host' command corresponds to one or more notification OIDs. Each of these notifications will have zero or more varbinds that are carried as payload - each MIB tells snmpd about these varbinds so that a 'notification view' can be built for them. An extra varbind - sysObjectID - is required to be sent with all v2c notifications. This message indicates that an attempt to register this varbind failed. Sending v2c notifications for the trapstring specified in the error message may fail. You can workaround this by not specifying any trapstring in the 'snmp host' configuration - this will enable all notifications for that destination.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-SNMP-3-TARGETNONE Cannot find notification target [chars]

Explanation    A configuration command refers to an SNMP target that has not yet been configured.

Recommended Action    You must configure an SNMP target before you can refer to it. Examine your configuration. Ensure that the given target has been configured. If it has not, configure it. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-3-TRANSPORTIO Failed to [chars] transport [chars]: [chars]

Explanation    Failed to communicate with the SNMP transport process. This could be due to a low memory condition, or the fact that there is no SNMP transport process running.

Recommended Action    Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SNMP-3-TRAPSEND Failed to send trap to [chars]

Explanation    A trap destined for the given address could not be sent. This could be due to a low memory condition. It also might be due to the fact that there is no SNMP transport process running for that transport protocol (e.g. udp_snmpd for SNMP over UDP).

Recommended Action    Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SNMP-3-TUPLEVALUE Failed to retrieve tuple [chars]%s: [chars]

Explanation    Failed to retrieve the given SysDB tuple for the given reason. This may or may not have a detrimental effect on the behavior of the SNMP agent (depends on which tuple it is).

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-CONFIGOPEN Failed to open snmp agent configuration file

Explanation    Failed to open snmp agent configuration file, /disk0/config/snmp/snmpd.cnf

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-DEBUGDUP Duplicate debug registration for the MIB [chars]

Explanation    The given MIB attempted to register for MIB debug handling more than once. This is an internal software error. It may not have a detrimental effect on the behavior of the SNMP agent.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-DEBUGFAIL Failed debug registration for the MIB [chars]

Explanation    Failed to initialize support for the command 'debug snmp mib xxx', where 'xxx' is the MIB indicated in the error message. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-SNMP-4-ENABLEFAILED Unable to parse tuple [chars] when trying to enable or disable a trap

Explanation    The SysDB tuple was not properly formatted, and hence could not be parsed. This will not degrade system performance, but the user will be unable to enable or disable some traps.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-ENABLENOTSUPPORTED Unrecognized trap type ([chars]). MIB is not loaded

Explanation    The snmp-server enable traps command allowed the user to set the specified traptype, but no callback function was registered to handle the command. This should have no detrimental effect on the system, but the user will not be able to enable/disable the specified trap.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-ENABLETRAPSTWICE [chars] MIB attempt to register same handler for the snmp enable traps [chars] command twice: handler: [hex]

Explanation    The given MIB attempted to register a second handler for the same traptype in the 'snmp enable traps ' command. This should have no detrimental effect on the behavior of the system.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-EXCEEDEDSIZE The maximum allowed size for enable trap tuple exceeded for [chars] trapstring

Explanation    While creating an enable trap tuple we exceeded the limit of maximum allowed size. The snmp enable trap command for this trapstring will not be NVGENed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-INIT_WARN Failed to [chars], cannot initialize: [chars]

Explanation    The requested operation could not be performed, due to the given reason. This could be due to a low memory condition, or an internal software error.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-SNMP-4-NOTIFYTWICE [chars] MIB attempt to register for [chars] notifications again: existing handlers: [hex] [hex]

Explanation    The given MIB attempted to register more than once for the given MIB notifications. This should have no detrimental effect on the behavior of the system.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-RESPONSE Failed to send response to [chars]

Explanation    A response destined for the given address could not be sent. This could be due to a low memory condition. It also might be due to the fact that there is no SNMP transport process running for that transport protocol (e.g. udp_snmpd for SNMP over UDP).

Recommended Action    Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SNMP-4-TARGETINUSE Notification target [chars] is in use

Explanation    An attempt was made to unconfigure an SNMP target, however that target is still in use by one or more other SNMP configuration commands.

Recommended Action    You must remove all other configuration commands that refer to this target before you can remove this target configuration. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-TIMER [chars]: [chars]

Explanation    Timer problem; internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-TRAPEMPTY Found empty trap, destined for [chars]

Explanation    A trap destined for the given address was empty. This is an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-VIEWFAIL Could not create view: [chars]

Explanation    Could not create an SNMP view using the 'snmp-server view' CLI command. Possible causes could be poorly formatted viewnames or oid subtrees.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-VIEWOID_NOT_FOUND The command [chars] could not be applied at this time because the oid [chars] does not belong to a known MIB module.

Explanation    The snmpd process attempted to load the view OID, but the OID did not correspond to any known MIB module.

Recommended Action    It could be that either - 1. the OID is of the format 'foobar.1', but the MIB module containing the OID 'foobar' is not yet loaded on the router. If this is the case, when the MIB is loaded, this command will be automatically applied - there is no need to re-enter it. 2. The MIB module containing the OID 'foobar' is indeed loaded, but the MIB did not load a translation from 'foobar' to '1.3.6.1.x.y.z' (i.e. there is no translation from the oid-name to the dotted decimal representation for that name). In this case, you can enter the dotted decimal version instead of the name, i.e. 'snmp-server view 1.3.6.1.x.y.z included' - note that using the dotted decimal version of the name will ALWAYS succeed without a warning message - it is upto the user to make sure the OID entered is valid. 3. The OID 'foobar.1' contains a typo - please re-enter the command with the correct OID and it should succeed. If the above steps result in repeated warning messages or failure, please contact your customer support representative wit the error message.

Error Message     
 
    
    
   

%SNMP-SNMP-4-WARN_BAG_REG Failed to register bags with SysDB for providing SNMP statistics and MIB information: [chars]

Explanation    Failed to register the bags with SysDB. The access to SNMP statistics and MIB items in /oper/snmp/info through 'sysdbcon' might not be available. This is likely due to an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-WARN_MEM_ALLOC Insufficient memory to [chars] [chars]

Explanation    Due to a low memory condition we could not enable (or disable) the specified traps or we could not register to receive the specified MIB notifications. Until available memory is increased and the SNMP process is restarted, these notifications will not be generated by the agent.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SNMP-4-WARN_SYSDB_BAG_ENCODE Failed to encode a bag due to [chars]

Explanation    Failed to encode a bag. The access to SNMP statistics and MIB information through 'show snmp' CLI command might not be available. This is likely due to an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-WARN_SYSDB_EDM_REG Failed to register as EDM for providing SNMP statistics and MIB information: [chars]

Explanation    Failed to register as EDM. The access to SNMP statistics and MIB information through 'show snmp' CLI command will not be available. This is likely due to an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-4-WARN_SYSDB_NOTIFY Failed to [chars] [chars]: [chars]

Explanation    Failed to register for receipt of the given notifications. This could be due to a low memory condition or an internal software error.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-SNMP-7-DEBUGINIT Failed debug registration for SNMP

Explanation    Failed to initialize support for the command 'debug snmp xxx', where xxx is one of the areas of debug interest within SNMP. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SNMP-7-MIBINSTALL [chars]

Explanation    An error was encountered during installation of a new MIB or deletion of an old MIB. These messages are printed when MIB installation/deletion failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SONETMIB Messages

Error Message     
 
    
    
   

%SNMP-SONETMIB-3-BAG An operation on a bag failed: [chars]

Explanation    A problem occurred while encoding or decoding information from a bag.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIB-3-BAG An operation on a bag failed: [chars]

Explanation    A problem occurred while encoding or decoding information from a bag.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIB-3-NOMEM_ERROR Failed to [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'

Error Message     
 
    
    
   

%SNMP-SONETMIB-3-NOMEM_ERROR Failed to [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'

Error Message     
 
    
    
   

%SNMP-SONETMIB-3-SYSDB_ACCESS Sysdb related error: [chars]

Explanation    The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIB-3-SYSDB_ACCESS Sysdb related error: [chars]

Explanation    The MIB had trouble reading from or writing to or binding/unbinding SysDB.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SONETMIBAPI Messages

Error Message     
 
    
    
   

%SNMP-SONETMIBAPI-2-THREAD_CREATE pthread_create([chars]) failed

Explanation    Sonet MIB API had trouble in creating thread.

Recommended Action    File a DDTS If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBAPI-3-BAG An operation on a bag failed: [chars]

Explanation    A problem occurred while encoding or decoding information from a bag.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBAPI-3-EVM_CREATE_ERR Event manager create failed : [chars]

Explanation    An internal operation failed. The system will attempt to recover.

Recommended Action    Copy the message exactly as it appears, and report it to your technical support representative.

Error Message     
 
    
    
   

%SNMP-SONETMIBAPI-3-NOMEM_ERROR Failed [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'

Error Message     
 
    
    
   

%SNMP-SONETMIBAPI-3-SYSDB_ACCESS Sysdb related error: [chars]

Explanation    SonetMIB API had trouble registering/deregistering EDM or binding/unbinding SysDB.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SONETMIBCORE Messages

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-2-THREAD_CREATE pthread_create([chars]) failed

Explanation    Sonet MIB API had trouble in creating thread.

Recommended Action    File a DDTS If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-3-BAG An operation on a bag failed: [chars]

Explanation    A problem occurred while encoding or decoding information from a bag.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-3-EVM_CREATE_ERR Event manager create failed : [chars]

Explanation    An internal operation failed. The system will attempt to recover.

Recommended Action    Copy the message exactly as it appears, and report it to your technical support representative.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-3-NOMEM_ERROR Failed [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-3-SYSDB_ACCESS Sysdb related error: [chars]

Explanation    SonetMIB API had trouble registering/deregistering EDM or binding/unbinding SysDB.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-7-DEBUG [chars]

Explanation    A Debug message

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-7-DEBUG2 [chars] : [chars]

Explanation    A Debug message

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-7-ERROR [chars] : [chars]

Explanation    An internal operation failed. The system will attempt to recover.

Recommended Action    Copy the message exactly as it appears, and report it to your technical support representative.

Error Message     
 
    
    
   

%SNMP-SONETMIBCORE-7-STATUS Send SNMP [chars] trap notification to [chars] : [hex]

Explanation    A Debug message

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

SYSLOGMIB Messages

Error Message     
 
    
    
   

%SNMP-SYSLOGMIB-3-NOMEM Insufficient memory to perform [chars] operation

Explanation    No memory in the process.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-SYSLOGMIB-3-PARSEERROR Failed to parse [chars]

Explanation    This is given out if there are problems parsing the encoded tuple from syslogd/sysdb.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-SYSLOGMIB-3-SYSDBERROR Failed to [chars]. Error: [chars]:

Explanation    The syslog mib reads the sysdb tuples and gets information about the syslog mib objects. If due to some reason the sysdb error occurs this message is printed out.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

UDPSNMP Messages

Error Message     
 
    
    
   

%SNMP-UDPSNMP-3-ERR_MEM_ALLOC Failed to [chars], due to lack of memory

Explanation    The requested operation could not be performed due to a low memory condition.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-UDPSNMP-3-ERR_SYSDB_ACCESS Failed to [chars] due to sysdb error:[chars]

Explanation    udp_snmpd reads the snmp trap Q length and trap timeout from the sysdb. If udp_snmpd is not able to read it then this error is printed. Or is printed when sysdb configuration for trap host does not have valid format. This is an internal error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-UDPSNMP-3-ERR_SYSDB_BIND Failed to bind to SysDB for [chars]: [chars]

Explanation    udp_snmpd binds to SysDB to receive notifications on the trap destinations udp_snmpd typically use these notifications to add trap destination to the trap Q. If udp_snmpd cannot bind to SysDB, these SysDB notifications will not be received, and thus some trap desination will not be added and traps will not be sent to those destinations.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-UDPSNMP-3-ERR_SYSDB_REG Failed to register for [chars] [chars]: [chars]

Explanation    Failed to register for receipt of the given notifications or receipt of the verification event. This could be due to a low memory condition or an internal software error.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-UDPSNMP-3-INIT Failed to [chars], cannot initialize: [chars]

Explanation    Initialization failed. This could be due to a low memory condition or an internal software error.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-UDPSNMP-3-SYSTEM Failed to [chars]

Explanation    Failed to execute a system call. This could be due to low memory condition or an internal software error.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*

Error Message     
 
    
    
   

%SNMP-UDPSNMP-4-AGENTIO_WARN [chars] [chars]: [chars]

Explanation    SNMP-UDP process received a bad Message or failed to send a message to Agent. This may be due to a invalid message number or an internal software error.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-UDPSNMP-4-NOVRF Failed to find VRF details for [dec]/[chars]

Explanation    Failed to find VRF related information that is required to send an SNMP PDU. This could be due to an internal software error.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-UDPSNMP-4-SYSMGR_INFORM Failed to inform SysMgr on SNMP-UDP initialization, [chars]

Explanation    Failed to inform SysMgr on end of initialization of UDP transport module for SNMP. This could be due to a block in snmpd initialization. If snmpd process does not come to normal execution even after some time need to take the recommended action.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Take the 'show processes blocked' and 'run attach_process -p '

Error Message     
 
    
    
   

%SNMP-UDPSNMP-7-INTERNAL_ERROR Failed to [chars]: [chars]

Explanation    Failed to initialize a functionality for snmp - like debugging, setup event manager for notification timer. Or failed to send PDU since the outgoing PDU is greater than the configured maximum PDU size, the PDU will be dropped. This could be due to an internal software error.

Recommended Action    If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

UTIL Messages

Error Message     
 
    
    
   

%SNMP-UTIL-3-NOINIT SNMP Utilities Library not properly initialized

Explanation    The SNMP Utilities library was not properly initialized by the SNMP agent. This is an internal software error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

VLANIFMIB Messages

Error Message     
 
    
    
   

%SNMP-VLANIFMIB-4-BAG Bag encode/decode Error : [chars]

Explanation    The VLAN Interface table relationship MIB encountered an error while encoding / decoding some data. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-VLANIFMIB-4-GEN Failed to [chars]

Explanation    The VLAN Interface table relationship MIB encountered an internal error during initialisation. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-VLANIFMIB-4-MEMORY Failed to [chars]

Explanation    The VLAN Interface table relationship MIB was unable to allocate sufficient memory to complete an operation. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%SNMP-VLANIFMIB-4-MIBLIB Failed to [chars]

Explanation    The VLAN Interface table relationship MIB encountered an internal error. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%SNMP-VLANIFMIB-4-SYSDB_ACCESS SysDB failed to [chars]

Explanation    The VLAN Interface table relationship MIB encountered an error while connecting to, or accessing data within the System Database. It is likely that an SNMP query that was in progress will not have been completed.

Recommended Action    Retry the operation that caused the message to be displayed. It may help to restart the SNMP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.