Cisco IOS XR System Error Reference Guide for XR12000 Series Platform Specific Messages, Release 3.4
Packet Infrastructure Messages
Downloads: This chapterpdf (PDF - 492.0KB) The complete bookPDF (PDF - 2.64MB) | Feedback

Packet Infrastructure Messages

Table Of Contents

Packet Infrastructure Messages

PA Messages

PAK_CAPTURE Messages

PAK Messages

PAKPLATFORM Messages

PAKSRV Messages

PAKWATCH Messages

PFI_IFH Messages

PFI Messages

PLATFORM_C12000_NETIO_LIB Messages

PLATFORM_HFR_NETIO_LIB Messages

PLATFORM_LPTS_COM_IFIB Messages

PLATFORM_LPTS_COM_NETIO Messages

PLATFORM_LPTS_LIB Messages

PLATFORM_LPTS_PIFIB Messages

PLATFORM_PFI Messages

PROTECT_NOTIFY Messages


Packet Infrastructure Messages


This section contains all Packet Infrastructure related System Error Messages, including ifmgr, tunnels, bundlemgr, pakman, and so forth. The following facility codes are represented in this module:

PA Messages

PAK_CAPTURE Messages

PAK Messages

PAKPLATFORM Messages

PAKSRV Messages

PAKWATCH Messages

PFI_IFH Messages

PFI Messages

PLATFORM_C12000_NETIO_LIB Messages

PLATFORM_HFR_NETIO_LIB Messages

PLATFORM_LPTS_COM_IFIB Messages

PLATFORM_LPTS_COM_NETIO Messages

PLATFORM_LPTS_LIB Messages

PLATFORM_LPTS_PIFIB Messages

PLATFORM_PFI Messages

PROTECT_NOTIFY Messages

PA Messages

Error Message     
 
    
    
   

%PKT_INFRA-PA-2-CTX_CREATE [chars]: Can't create VRF context structures. VRF '[chars]' ([hex]) error [chars] ([unsigned int])

Explanation    PA Can't create VFR context structures.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-2-INFRA_FAIL [chars]: [chars] failed rc=[dec]

Explanation    There was a ENA infra call failure resulting in a failure to provide some infrastructure service.

Recommended Action    Copy the error message exactly as it appears, and report it to your technical support representative.

Error Message     
 
    
    
   

%PKT_INFRA-PA-2-RSI_ERROR RSI [chars] failed error [chars] ([unsigned int])

Explanation    RSI error

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-2-RSI_UNKNOWN_EVENT Unknown event from RSI event [unsigned int]

Explanation    RSI sent unknown event

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ECM_SETRETRY_FAIL Error setting linear connection retry mechanism : [chars]

Explanation    Failed to set linear connection retry mechanism in Port Arbitrator Client

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_ADD_SLICE [chars]: Assign of slice [chars] to node [hex] failed. ([chars])

Explanation    The PA failed to assign an IFIB slice.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_BACKEND [chars]: [chars] failed

Explanation    Sysdb backend api call failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_BAG [chars]: [chars] failed: [chars]

Explanation    Bag api call failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_FM_MSG_TIMEOUT [chars]: [chars] update of slice [chars] to node [hex] timed out.

Explanation    The PA failed to receive a response to an IFIB table update or an IFIB slice assignment update message.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_LOCK [chars] line [dec]: error: [chars]

Explanation    An attempt to lock a mutex failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_PIFIB_MSG_TIMEOUT [chars]: Pre-IFIB update for slice [chars] timed out.

Explanation    The PA failed to receive a response to a critical Pre-IFIB update.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_SYSDB [chars]: [chars] failed
[chars]

Explanation    Sysdb api call failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-ERR_UNLOCK [chars] line [dec]: error: [chars]

Explanation    An attempt to lock a mutex failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-3-EVENT_REGISTRATION_FAILED PA failed to connect to the event manager: [chars]

Explanation    The PA process failed while attempting to connect to an event manager channel for the indicated subsystem.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PA-6-INFO_GENERAL [chars]: [chars]

Explanation    The PA encountered some problem in genric nature or plain information.

Recommended Action    Copy the error message exactly as it appears, and report it to your technical support representative.

PAK_CAPTURE Messages

Error Message     
 
    
    
   

%PKT_INFRA-PAK_CAPTURE-4-ECC_ERROR packet dropped in hw due to programming error: pkt type [hex] pkt: [chars]

Explanation    A packet was dropped in hardware due to bad programming or a hardware error. This is a raw dump of the packet to aid in debugging.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PAK Messages

Error Message     
 
    
    
   

%PKT_INFRA-PAK-3-DEBUGINITFAIL [chars]

Explanation    An error occurred during packet debug events initilization. Refer to the error message for the particular cause.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAK-7-EXCEPTION_LITE packet exception, reason: [chars]

Explanation    An software exception had occurred in the packet manager library. The client process terminated with exit code -1. The reason is that the client passed an invalid packet to packet manager library and led to the exception.

Recommended Action    Normally the client process will restart and re-connect to packet manager. If any of these messages recur, call your technical support representative for assistance.

PAKPLATFORM Messages

Error Message     
 
    
    
   

%PKT_INFRA-PAKPLATFORM-3-CONNECTFAIL Connect to the packet server failed. Reason : [chars]

Explanation    The platform driver was not able to connect to the packet server.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PAKPLATFORM-6-SENDFAIL Send data to the packet server failed. Reason : [chars]

Explanation    The platform driver was not able to send data to the packet manager. This could happen when the platform driver is trying to send the initilization information to the packet manager.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PAKSRV Messages

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-2-ERR_MUTEX_REVIVAL Failed to revive the packet mutex, reason: [chars]

Explanation    The packet subsystem failed to revive the packet mutex.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-2-MEMUTILMAPFAIL Memory mapping for [chars] failed, reason: [chars]

Explanation    Memory maping for the specified area failed and packet server will restart.

Recommended Action    If the error is not rectified after two or more restarts, please call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-3-BADPAK Corruption detected in the [chars] at [pointer] owned by packet [pointer] belonging to process [dec]

Explanation    Consistency check detected corruption in the specified area of the specified packet. This will cause packet manager to restart. Please report the message and value to your technical support representative.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-3-DIAGFAIL Packet server: line [dec], fatal misalignment.

Explanation    Packet server internal structures are misaligned. This is a fatal programming error. The value is a marker for tracking down the misalignment. Please report the message and value to your technical support representative.

Recommended Action    Call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-3-ERR_MEM_ALLOC Memory allocation failed in process [dec] at [chars]

Explanation    Packet server failed to allocate more memory.

Recommended Action    It may be necessary to free some memory by exiting a program. If this message recurs, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-BADPTCL_DUMP [chars]: [chars]

Explanation    Particle body corruption is detected. This message follows a BADPAK message and dumps the first few bytes of the particle body and the last few bytes of the one before.

Recommended Action    None. This is message is only for debugging purpose.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-BCASTFAIL Failed to send broadcast message [dec] to client [dec], error: [chars]

Explanation    Packet server failed to send a broadcast message to the client. This will result in the client being unaware of an event that occurred in the packet server.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-CHANCREATEFAIL Failed to create a channel and event manager, error: [chars]

Explanation    Packet server failed to create an event manager and channel. Clients will be unable to connect to packet server, and packet server will be unable to send and receive messages.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-CHUNKCREATEFAIL Chunk creation for packet headers failed

Explanation    Could not allocate a chunk of memory for the packet headers.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-CONDWAITFAIL Conditional wait operation on [chars] in [chars] failed; reason [chars]

Explanation    The packet subsystem failed to perform a conditional wait. This usually indicates a programming error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-DEBUGINITFAIL Packet server debug initialization: [chars] failed, error [chars]

Explanation    The debug support initalization failed in the packet server. It will be restarted by sysmgr and should recover.

Recommended Action    If packet manager is unable to start up after several restarts by sysmgr, please collect the 'sh log' output and contact your customer support representative.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-DEQUEUEFAIL Failed to remove client [dec] from clients list at [chars]

Explanation    Packet server failed to remove the specified client from the client list queue. This may cause the client fail to reconnect to packet server.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ENQUEUEFAIL Fail to insert client [dec] into the list of clients at [chars]

Explanation    Packet Server failed to insert a client into client list queue. This will prevent the client from connecting to packet server.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_CHKPT_OP [chars]: [chars] check point operation failed, reason : [chars]

Explanation    A check point operation failed in packet manager.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_EVM_ATTACH Failed to attach event handler.

Explanation    The packet subsystem encountered an error when attaching a handler for synchronous or asynchronous events.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_MUTEX_INIT Failed to initialize packet mutex, reason: [chars]

Explanation    The packet subsystem failed to initialize the packet mutex.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_MUTEX_MONREG Packet server registration for mutex monitoring (revival) failed, error [chars]

Explanation    Packet server failed to register for the mutex revival and will exit. It will be restarted by sysmgr.

Recommended Action    If packet manager is unable to start up after several restarts by sysmgr, please collect the 'sh log' output and contact your customer support representative.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_MUTEX_OP Mutex [chars] operation on [chars] in [chars] failed; reason [chars]

Explanation    The packet subsystem failed to perform the specified operation on the specified mutex. This usually indicates a programming error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_THREAD_ATTR_SET [chars]: Failed to set thread attributes

Explanation    Packet server unable to set the thread's attributes.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_THREAD_CREATE Failed to create the [chars] thread

Explanation    Packet server was unable to create the specified thread.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-ERR_THREAD_DETACH [chars]: Failed to detach from a new thread

Explanation    Packet server was unable to detach from a new thread.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-FSVFAIL [chars]: fsv_register for name=[chars] failed, error : [dec]

Explanation    An automatic register for one of the FSVs failed.

Recommended Action    If any of these messages occur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-GET_RENDEZVOUS msg_chan_get_rendezvous failure: [chars].

Explanation    msg_chan_get_rendezvous failed.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-GETNODENAMEFAIL failed to get node name in pakman server init

Explanation    packet manager server unable to retrieve the hostname for node/linecard.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-GETPIDFAIL Failed to get client's pid at [chars]

Explanation    Packet Server failed to get the client's pid. This will prevent the client from connecting to packet server.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-HSSDFAIL [chars]: hssd_register for name=[chars],size=[dec] failed, error : [dec]

Explanation    An automatic register for one of the HSSDs failed.

Recommended Action    If any of these messages occur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-INITFAIL Packet server initialization failed. Reason : [chars]

Explanation    The packet subsystem was not able to initialize properly. It will be restarted by sysmgr and should recover.

Recommended Action    If packet manager is unable to start up after several restarts by sysmgr, please collect the 'sh log' output and contact your customer support representative.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-MSGREPLYFAIL Failed to reply to client [dec] message [dec] at [chars]

Explanation    Packet server failed to reply to a client's request. This will result in the client getting blocked on packet server.

Recommended Action    Restart the specified client. If the problem is not rectified, contact customer support.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-PAKBCASTFAIL Broadcast to clients from packet server failed

Explanation    Packet server failed to broadcast to message to its clients that it is about to restart.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-PARTICLEINITFAIL Particle initialization failed.

Explanation    Packet server was not able to initialize the particles correctly and will restart.

Recommended Action    If the error is not rectified after two or more restarts, please call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-QSM_ADD_SERVICE qsm_add_service failure: [chars].

Explanation    qsm_add_service failed.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-SIGALRM Received SIGALRM unexpectedly, ignored.

Explanation    An unexpected signal SIGALRM was received.

Recommended Action    If any of these messages occur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-SIGNAL signal: [chars].

Explanation    The packet subsystem encountered an error while performing a signal operation.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-SYSMGR_GET_NODE_STATE Failed to get node state from Sysmgr: [chars].

Explanation    Packet server failed to get node state from sysmgr.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

Error Message     
 
    
    
   

%PKT_INFRA-PAKSRV-7-TIMER [chars]: timer: [chars].

Explanation    The packet subsystem encountered an error while operating/handling a timer.

Recommended Action    If any of these messages recur, call your technical support representative for assistance.

PAKWATCH Messages

Error Message     
 
    
    
   

%PKT_INFRA-PAKWATCH-6-INFO Depletion level [dec] percent




for resource [chars]:

Explanation    The info about the current depletion level of the specified resource.

Recommended Action    It is an informational message.

Error Message     
 
    
    
   

%PKT_INFRA-PAKWATCH-6-INFO_BODY [chars] [dec] [dec]

Explanation    The resource depletion information in the following format: PROCESS_NAME PID COUNT

Recommended Action    It is an informational message.

Error Message     
 
    
    
   

%PKT_INFRA-PAKWATCH-6-INFO_HEAD [chars] [chars] [chars]

Explanation    The header for resource depletion information that follows this message. It is of the format: PROCESS_NAME PID COUNT

Recommended Action    It is an informational message.

Error Message     
 
    
    
   

%PKT_INFRA-PAKWATCH-6-TRACEBACK [chars]

Explanation    The traceback info about caller

Recommended Action    It is an informational message.

Error Message     
 
    
    
   

%PKT_INFRA-PAKWATCH-6-USER_INFO Top [dec] users of [chars]:

Explanation    The info about the top users of the specified resource.

Recommended Action    It is an informational message.

Error Message     
 
    
    
   

%PKT_INFRA-PAKWATCH-6-USER_INFO2 Only [dec] users found using [chars].

Explanation    The info about the total number of users of the specified resource.

Recommended Action    It is an informational message.

PFI_IFH Messages

Error Message     
 
    
    
   

%PKT_INFRA-PFI_IFH-4-FAIL [chars]: [chars] ([hex])

Explanation    An error occured in the ifh process. This may lead to problems elsewhere in the system.

Recommended Action    If no further problems are seen, this warning may probably safely be ignored. If the message recurs, or problems are seen elsewhere in the system, take the following action. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PFI Messages

Error Message     
 
    
    
   

%PKT_INFRA-PFI-3-ASSERT Fatal error - assert condition [chars] failed - [chars] thread [dec]

Explanation    Internal error

Recommended Action    'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

PLATFORM_C12000_NETIO_LIB Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface

Explanation    The FINT idb is not yet created in netio. This could be a transient condition.

Recommended Action    Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface

Explanation    The FINT idb is not yet created in netio. This could be a transient condition.

Recommended Action    Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars]

Explanation    Unable to determine my node id using platform api.

Recommended Action    Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars]

Explanation    Unable to determine my node id using platform api.

Recommended Action    Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_PPINDEX_INFO_FAIL Lookup for ppindex([dec]), pp_proto([dec]), failed due to [chars]

Explanation    Unable to get the adjacency and next hop information from given ppindex.

Recommended Action    Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked

PLATFORM_HFR_NETIO_LIB Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_HFR_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface

Explanation    The FINT idb is not yet created in netio. This could be a transient condition.

Recommended Action    Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_HFR_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars]

Explanation    Unable to determine my node id using platform api.

Recommended Action    Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

PLATFORM_LPTS_COM_IFIB Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_MISSING_FLOW [chars]: Flow type '[chars]' not configured

Explanation    error in IFIB flow handling configuration. The named flow type was not explicitly configured and will have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_MISSING_PARAMETER [chars]: Missing parameter after '[chars]' in flow '[chars]'

Explanation    Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in flow '[chars]'

Explanation    Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_UNKNOWN_PARAMETER [chars]: Unknown parameter '[chars]' after '[chars]' in flow '[chars]'

Explanation    Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-ERR_MEM_ALLOC Failed to allocate memory

Explanation    The system failed to allocate memory. It's likely that the system is running low in memory.

Recommended Action    This indicates a low-memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-NO_CONFIG [chars]: Missing configuration for IFIB flow handling

Explanation    No configuration for IFIB flow handling was found. Default characteristics will be used for all packets.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-NO_CONFIG_MEMORY [chars]: Insufficient memory for IFIB flow handling configuration

Explanation    Insufficient memory was available for storing the IFIB flow handling configuration. Default characteristics will be used for all packets.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]

Explanation    An error was returned when calling debug_cleanup() function.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]

Explanation    An error was returned when calling the debug_init_event() function.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]

Explanation    An error was returned when calling debug_register() function.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-ERR_DEBUG_INIT [chars]: [chars]

Explanation    An error was returned when initializing debug. The facility to debug the component may not work.

Recommended Action    Debug message only. No action is required.

PLATFORM_LPTS_COM_NETIO Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]

Explanation    An error was returned when cleaning up debug.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]

Explanation    An error was returned when calling debug_cleanup() function.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]

Explanation    An error was returned when initializing debug.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]

Explanation    An error was returned when calling the debug_init_event() function.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]

Explanation    An error was returned when calling debug_register() function.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]

Explanation    An error was returned when registering debug.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PLATFORM_LPTS_LIB Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_LIB-7-ERR_DEBUG_INIT [chars]: [chars]

Explanation    An error was returned when initializing debug. The facility to debug the component may not work.

Recommended Action    Debug message only. No action is required.

PLATFORM_LPTS_PIFIB Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-BACKEND_EDM [chars]: EDM backend function [chars] failed: [chars]

Explanation    An internal EDM backend function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-BAG [chars]: Bag function [chars] failed: [chars]

Explanation    An internal bag function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CHKPT_INIT [chars]: Checkpoint Initialization function [chars] failed: [chars]

Explanation    An internal Checkpoint function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_FLOW_MEMORY [chars]: Insufficient memory for flow configuration

Explanation    There is insufficient memory for the flow configuration. All flows will be assigned default characteristics.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_MISSING_FLOW [chars]: Flow type '[chars]' not configured

Explanation    error in PIFIB flow handling configuration. The named flow type was not explicitly configured and will have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_MISSING_PARAMETER [chars]: Missing parameter after '[chars]' in flow '[chars]'

Explanation    Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_MEMORY [chars]: Insufficient memory for policer configuration

Explanation    There is insufficient memory for the policer configuration. All flows will be assigned default characteristics.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_PARAMETER_INVALID [chars]: Invalid parameter '[chars]' after '[chars]' in policer '[dec]' definition

Explanation    There is an invalid parameter after a keyword in a policer definition. The policer may be assigned default characterstics.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_PARAMETER_MISSING [chars]: Missing parameter after '[chars]' in policer '[dec]' definition

Explanation    There is a missing required parameter after a keyword in a policer definition. The policer may be assigned default characterstics.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in policer '[dec]' definition

Explanation    There is an unknown keyword in a policer definition. The policer may be assigned default characterstics.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNDEFINED_POLICER [chars]: flow '[chars]' references undefined policer '[dec]'

Explanation    An input flow definition references an undefined policer. The flow will be configured to use policer 0.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in flow '[chars]'

Explanation    Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNKNOWN_PARAMETER [chars]: Unknown parameter '[chars]' in flow '[chars]'

Explanation    Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-ERR_IFH_UIDB_INDEX Failed to find uidb index for interface handle [hex]

Explanation    Failed to find uidb index for an given interface handle. It is likely to be caused by a programming bug or a programming problem happened in the past.

Recommended Action    Run the command 'show uidb index' to verify whether the uidb index is created for the interface. Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-ERR_MEM_ALLOC Failed to allocate memory

Explanation    The system failed to allocate memory. It's likely that the system is running low in memory.

Recommended Action    When this issue happens, it will trigger an automatic restart. This indicates a low-memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-ERR_NOTIF_Q_FULL The queue for notifications from [chars] is full

Explanation    Too many notifications have been sent to the component. The queue to hold the notification has overflowed.

Recommended Action    When this issue happens, it will trigger an automatic restart. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-EVENT_CONN_CREATE [chars]: could not create event connection: [chars]

Explanation    An internal error was detected when trying to create event connection.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-EVENT_CONN_OPEN [chars]: could not open event connection: [chars]

Explanation    An internal error was detected when trying to open event connection.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_ADD_FEAT2GRP [chars]: fm add feat to group failed for ISIS [chars]

Explanation    An internal fm add feature to group function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_ADD_IFH2GRP [chars]: fm add ifh to group failed for ISIS [chars]

Explanation    An internal fm add ifh to group function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_CREATE_GROUP [chars]: fm create group failed: [chars]

Explanation    An internal fm create group function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_FEAT_PROCESSING [chars]: fm feature registration failed: [chars]

Explanation    An internal fm feature registration function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_REGISTER [chars]: fm_register failed: [chars]

Explanation    An internal fm_register function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-HFA_REGISTER [chars]: hfa_register failed: [chars]

Explanation    An internal hfa_register function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-LTRACE_INIT [chars]: ltrace_init2 failed: [chars]

Explanation    An internal ltrace_init2 function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-MSG_ATTACH [chars]: Event Mgr function [chars] failed: [chars]

Explanation    An internal Event Manager function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-NO_CONFIG [chars]: Missing configuration for PIFIB flow handling

Explanation    No configuration for PIFIB flow handling was found. Default characteristics will be used for all packets.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SHOW_EDM_CLOSE [chars]: Cleanup for EDM failed: [chars]

Explanation    Cleanup for EDM failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SHOW_EDM_INIT [chars]: Initialization for show EDM failed: [chars]

Explanation    Initialization for show EDM failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SYSDB [chars]: Sysdb function [chars] failed: [chars]

Explanation    An internal sysdb function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-TCAM_FMT_TO_HFA_MAP [chars]: vmr_builder_program_tcam_fmt_from_hfa_map failed: [chars]

Explanation    An tcam format to hfa mapping function failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-5-ERR_MSTATS_ALLOC Failed to allocate HW counters.

Explanation    It failed to allocate HW counters. It may be because of running out of HW counters or encountering internal error.

Recommended Action    Disable the numbers of non crucial services which use HW counters.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-5-ERR_TCAM_INVALID_REG_NAME Found the Pre-IFIB region with unrecognized name: [chars]

Explanation    A Pre-IFIB region with unrecognized name is found in the TCAM. It is likely caused by a programming bug or a programming problem happened in the past.

Recommended Action    Check the status of TCAM Manger because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-5-ERR_TCAM_OVERFLOW Does not have enough space for the Pre-IFIB entry in TCAM region [chars]

Explanation    TCAM space is not enough for all Pre-IFIB entries in the particular TCAM region. All control packets which do not have matching Pre-IFIB entries in TCAM will use SW path to forward to destinations.

Recommended Action    Disable the numbers of services configured for the system.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-5-ERR_TCAM_PREFIX_COMPRESS Failed to have IPv6 prefix compressed

Explanation    IPv6 prefix compression failed because the line card has run out of internal resources for compressing a preifx. It shouldn't have any major impact on the system service. The in-bound (destined to the system) packets can still reach destinations through SW path.

Recommended Action    Try either change the prefix length or change the prefix value of IPv6 addressses used in the system if possible.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]

Explanation    An error was returned when cleaning up debug.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]

Explanation    An error was returned when initializing debug.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]

Explanation    An error was returned when registering debug.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_CONN_INIT Failed to connect to [chars]: [chars]

Explanation    An internal error was detected when trying to connect to the respective component.

Recommended Action    When this issue happens, it will trigger an automatic restart. Check the status of the respective component because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_DEBUG_INIT [chars]: [chars]

Explanation    An error was returned when initializing debug. The facility to debug the component may not work.

Recommended Action    Debug message only. No action is required.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_EVM_INIT [chars]: [chars]

Explanation    An internal error was detected when trying to set up event connection.

Recommended Action    When this issue happens, it will trigger an automatic restart. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_EVM_TM_ATTACH Could not set up a timer object: [chars]

Explanation    An internal error was detected when trying to allocate a timer object.

Recommended Action    When this issue happens, it will trigger an automatic restart. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_EVM_TM_LEAF_NEW Could not create a timer tree leaf objct: [chars]

Explanation    An internal error was detected when trying to create a timer tree leaf object.

Recommended Action    When this issue happens, it will trigger an automatic restart. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_INIT_POLICERS Failed to initialize the flow policer [dec]: [chars]

Explanation    It failed to program a flow policer during initialization.

Recommended Action    When this issue happens, it will trigger an automatic restart. Check the status of Metro IPC Server because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_LTRACE_INIT Failed to initialize the ltrace buffer

Explanation    An internal error was detected when trying to initalize a ltrace buffer.

Recommended Action    When this issue happens, it will not able to use ltrace buffer for debugging. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_MIPC_INIT Failed to initialize with Metro IPC Server: [chars]

Explanation    An internal error was detected when trying to initialize with Metro IPC server.

Recommended Action    Check the status of Metro IPC Server because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_MIPC_NOTIF_ACK Failed to acknowledge a MIPC notification: [chars]

Explanation    It is an internal error which the system failed to acknowledge a MIPC Server notification.

Recommended Action    When this issue happens, it will trigger an automatic restart. Check the status of Metro IPC Server because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_MSTATS_INIT Failed to initialize stats table: [chars]

Explanation    An internal error was detected when trying to initialize a statistic counter table.

Recommended Action    Check the status of Metro Stats Server because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_NOTIF_HANDLE Failed to handle [chars] notification: [chars]

Explanation    An internal error was detected when trying to handle a notification from the respective component.

Recommended Action    When this issue happens, it will trigger an automatic restart. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_PROGRAM_ERRORED_POLICER Failed to reprogram the flow policer [dec]: [chars]

Explanation    An internal error was detected when trying to program the flow policer.

Recommended Action    When this issue happens, it will trigger an automatic restart. Check the status of Metro IPC Server because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_REPROGRAM_POLICERS Failed to program the flow policer [dec]: [chars]

Explanation    It failed to reprogram a flow policer when it had received a request to reprogram all flow policers to HW.

Recommended Action    When this issue happens, it will trigger an automatic restart. Check the status of Metro IPC Server because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_SYSDB_DATALIST_CREATE Sysdb datalist function failed to create an object handle: [chars]

Explanation    An internal sysdb function failed.

Recommended Action    When this issue happens, it will trigger an automatic restart. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-ERR_TCAM_INIT Failed to initialize TCAM regions: [chars]

Explanation    An internal error was detected when trying to initialize TCAM regions.

Recommended Action    Check the status of TCAM Manger because this issue is likely related to it. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PLATFORM_PFI Messages

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_PFI-4-IFHANDLE_DECODE Could not map handle [hex] to slot

Explanation    The interface handle cannot be mapped to a slot on the card.

Recommended Action    Debug message only. *DEBUG*

Error Message     
 
    
    
   

%PKT_INFRA-PLATFORM_PFI-4-INIT Failed to initialise [chars]

Explanation    An error occured when a module was going to be initialised. This may cause the process to terminate.

Recommended Action    Restarting the process might help.

PROTECT_NOTIFY Messages

Error Message     
 
    
    
   

%PKT_INFRA-PROTECT_NOTIFY-3-DRIVER_CONFIG Config of i/f driver to generate fast notifictaions failed: [chars] - [chars]

Explanation    Configuration of interface driver to generate traffic protection fast notifications failed. Fast (e.g. sub 50ms) protection is not available for interfaces on the affected linecard. Note that while the traffic fast protection is affected in terms of speed, in the absence of additional errors the corresponding protection method (e.g. MPLS TE FRR) should still protect, but at much slower (over 50ms) speeds.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PROTECT_NOTIFY-3-TRIGGER Fast protection trigger failed: [chars] - [chars]

Explanation    Fast protection trigger failed for reasons as specified. Note that while the traffic fast protection is affected in terms of speed, in the absence of additional errors the corresponding protection method (e.g. MPLS TE FRR) should still protect, but at much slower (over 50ms) speeds.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%PKT_INFRA-PROTECT_NOTIFY-6-CLIENT_INIT Init of notifications client failed: [chars] - [chars]

Explanation    Initialization of traffic protection fast notifications client failed. This can happen during normal operation due to a non-optimal initialization order. As client re-tries the initialization this message can be ignored. However if this message repeats for prolonged period of time or if more severe messages are observed the fast (e.g. sub 50ms) protection may become not available for interfaces protected by this client. Note that even if fast protection becomes not available, the corresponding protection method (e.g. MPLS TE FRR) should still protect, but at much slower (over 50ms) speeds.

Recommended Action    Monitor for repetition of this message or presence of more severe errors.

Error Message     
 
    
    
   

%PKT_INFRA-PROTECT_NOTIFY-7-SERVER_INIT Init of notifications server failed: [chars] - [chars]

Explanation    Initialization of traffic protection fast notifications server failed. Fast (e.g. sub 50ms) protection is not available for interfaces on the affected linecard. Note that while the traffic fast protection is affected in terms of speed, in the absence of additional errors the corresponding protection method (e.g. MPLS TE FRR) should still protect, but at much slower (over 50ms) speeds.

Explanation    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.