Cisco IOS XR System Error Reference Guide for CRS-1 Router Platform Specific Messages, Release 3.3
High Availability (HA) Messages
Downloads: This chapterpdf (PDF - 183.0KB) The complete bookPDF (PDF - 1.82MB) | Feedback

High Availability (HA) Messages

Table Of Contents

High Availability (HA) Messages

LRD_inv Messages

REDDRV Messages


High Availability (HA) Messages


This section contains all High Availability related System Error Messages. The following facility codes are represented in this module:

LRD_inv Messages

REDDRV Messages

LRD_inv Messages

Error Message     
 
    
    
   

%HA-LRD_inv-3-BAG_REGISTRATION Unable to register LRd's bag structures. '[chars]'

Explanation    LRd was unable to register bag structures.

Recommended Action    Contact support.

Error Message     
 
    
    
   

%HA-LRD_inv-3-MEM_ALLOC_FAIL Failed to allocated [dec] bytes of memory: [chars]

Explanation    The requested operation could not be accomplished because of a low memory condition.

Recommended Action    Contact TAC.

Error Message     
 
    
    
   

%HA-LRD_inv-3-MSG_CERR_REGISTER_DLL Could not register dll with error services: [chars]

Explanation    The call register the dll using cerr_register_dll failed.

Recommended Action    Contact support.

Error Message     
 
    
    
   

%HA-LRD_inv-3-MSG_INVENTORY_FWD Error forwarding inventory: '[chars]'

Explanation    LRd was unable to read or write information needed to forward inventory in Admin space to the LR Plane.

Recommended Action    Contact support.

Error Message     
 
    
    
   

%HA-LRD_inv-3-REDUNDANCY_STATE Unrecognized redundancy state [dec]

Explanation    LRd doesn't recognize redundancy state.

Recommended Action    Contact support.

Error Message     
 
    
    
   

%HA-LRD_inv-3-SYSDB_ITEM_ERROR sysdb_item_[chars]([chars]) returned '[chars]'

Explanation    SysDB returned an error to LRd.

Recommended Action    Contact support.

Error Message     
 
    
    
   

%HA-LRD_inv-4-CANT_FIND_DSC LR Daemon library could not find the dSC.

Explanation    LRdlib could not find the dSC.

Recommended Action    Collect system log information. No action is required.

Error Message     
 
    
    
   

%HA-LRD_inv-4-UNEXPECTED Unexpected: [chars]: [chars]: [hex]

Explanation    An unexpected condition encountered. This is not necessarily an error, but may help with debugging other problems elsewhere!

Recommended Action    Collect system log information. No action is required.

Error Message     
 
    
    
   

%HA-LRD_inv-6-NON_DRP_PRIMARY WARNING: A node with unknown type or a non RP/DRP node [chars] is used as primary for SDR

Explanation    This is an informational message output during SDR configuration commit time only if a non-RP or non-DRP node is being assigned as primary to the SDR. Please note that if the node is not in IOX-RUN state, it's node type will not be determined.

Recommended Action    Verify the card type in the slot being configured as primary for the SDR. If not a DRP or RP card, please replace with valid card type.

Error Message     
 
    
    
   

%HA-LRD_inv-6-RESET_CARD_FOR_PAIRING LRd has reset the DRP '[dec]' to accomodate new pairing configuration.

Explanation    The DRP pairing configuration was changed. The card entering or leaving the pair needs to be reset in order to accomodate the new configuration.

Recommended Action    None.

Error Message     
 
    
    
   

%HA-LRD_inv-6-UNPAIRED_DRP WARNING: A unpaired DRP node [chars] is being added as primary to SDR

Explanation    This is an informational message output during SDR configuration commit time only if an unpaired DRP node is being assigned to an SDR.

Recommended Action    *none*

REDDRV Messages

Error Message     
 
    
    
   

%HA-REDDRV-2-MSG_PRIMARY_GLARE primary-primary glare (primary msg from node [hex])

Explanation    There appear to be two PRIMARY RP's in the system

Recommended Action    None; the node which has arbitrated for the least time will be reset.

Error Message     
 
    
    
   

%HA-REDDRV-3-ERROR_EXIT reddrv process exiting because [chars], error code [chars]

Explanation    The DRP redundancy driver process exited for the reason mentioned in the message.

Recommended Action    The System Manager process (sysmgr) will automatically respawn this process up to a fixed number of times when this error is encountered inorder to recover. Execute 'show process reddrv location ' to verify that the process is up and running after the restart. If it is still non-operational, try doing from the admin mode 'process restart reddrv location '. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-3-ROLE_LOCKED (node [hex]) failover prevented - card role is locked

Explanation    The role of this card has been locked - failover was prevented.

Recommended Action    A failover was initiated, but could not complete because the card role is locked. Please capture the output of 'show reddrv trace' and 'show drp-reddrv trace'.

Error Message     
 
    
    
   

%HA-REDDRV-4-CRITERIA_CONFLICT Detected conflicting criteria comparision: [chars]

Explanation    Detected conflicting criteria.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-4-FILE_OPEN Failed to open log file for redundancy driver: [chars]

Explanation    Failed to open log file for redundancy driver.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-4-HARDWARE_ERROR Detected Hardware error: [chars].

Explanation    Detected hardware error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-4-WD_EXPIRED Failed to punch the watchdog on time [dec] seconds [dec] nanosecs

Explanation    Failed to punch the watchdog timer within one second.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-5-GO_ACTIVE Card is becoming active.

Explanation    Card is becoming active.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-5-GO_BID Card is going to bid state.

Explanation    Card is going to bid state.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-5-GO_STANDBY Card is becoming standby.

Explanation    Card is becoming standby.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-6-MSG_TRANSIT_TO_BID (slot [dec]) transit to bid state

Explanation    This particular DRP has entered a bid to become PRIMARY.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-6-MSG_TRANSIT_TO_FAILOVER (node [hex]) transit to failover state

Explanation    This particular DRP has entered been told to be a non-participant, and give up.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-6-MSG_TRANSIT_TO_PRIMARY (node [hex]) transit to primary state

Explanation    This particular DRP has succeeded in its bid to become PRIMARY.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-6-MSG_TRANSIT_TO_STANDBY (node [hex]) transit to standby state

Explanation    This particular DRP has failed in its bid to become PRIMARY, and is now operating as a STANDBY unit.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-6-RESET_SELF No active RP detected for [dec] seconds; resetting this node

Explanation    The node on which reddrv is running, resets itself on loss of heartbeat from the RP.

Recommended Action    Check the RP in the system. If present, check the connectivity between RP and the node that went down.

Error Message     
 
    
    
   

%HA-REDDRV-6-RESET_STANDBY Active [chars] reset standby peer node [chars]

Explanation    Issue hardware reset to peer standby RP or SC.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-ASYNC_SEND Failed to send async message to redcon : [chars]

Explanation    Failed to send async message to redcon.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-ERROR [chars] : [chars]

Explanation    A general failure occured while executing a resource function. The message contains info about the cause of the failure and possibly anticipated actions/effects.

Recommended Action    Verify continued correct operation of Redundancy Driver.

Error Message     
 
    
    
   

%HA-REDDRV-7-KDUMPER_MESSAGE [chars]

Explanation    Reddrv has received kernel dumper message

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-MESSAGE_RETRY_ERROR Exhausted message retry count of messge type: [chars]

Explanation    Received unexpected async error message code.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-MISS_ACK_COUNT Missed heart beat acknowledge from standby

Explanation    Received unexpected async error message code.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-MSG_ERROR Received unexpected message of type: [dec]

Explanation    Received unexpected message.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-MSG_INVALID_MSGLEN reddrv_msg_handler got [dec] expected [dec]

Explanation    reddrv_msg_handler received a message of unexpected size

Recommended Action    No action required, software will take corrective action on its own.

Error Message     
 
    
    
   

%HA-REDDRV-7-NODE_ERROR [chars] : [chars] : [chars]

Explanation    Reddrv had problem to broadcast dead node name notification.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.=

Error Message     
 
    
    
   

%HA-REDDRV-7-NODE_RESET Resetting node [chars] for correct active/standby arbitration

Explanation    The arbitration state machine needs to be able to reset failed nodes, or other nodes on the same card as a failed node, in order to ensure correct behavior of the state machine and no mixed-role cards.

Recommended Action    No action required, just informational message.

Error Message     
 
    
    
   

%HA-REDDRV-7-NODE_RESET_FAILED Reset of node [chars] failed with error [chars] - correct active/standby arbitration may not occur in this case

Explanation    The arbitration state machine needs to be able to reset failed nodes, or other nodes on the same card as a failed node, in order to ensure correct behavior of the state machine and no mixed-role cards. If this fails, then arbitration may not occur correctly.

Recommended Action    Please collect output of 'show redundancy trace', 'show logging' and 'show ltrace shelfmgr'.

Error Message     
 
    
    
   

%HA-REDDRV-7-OPERATION_FAIL Failed to [chars], error code [chars]

Explanation    The particular operation mentioned in the message failed due to some reason. This is not a critical failure, the process can continue functioning as expected despite the failure.

Recommended Action    Debug message only. No action is required.

Error Message     
 
    
    
   

%HA-REDDRV-7-REDCON_REREGISTER Recon registration invoked more than once

Explanation    The reddrv_redcon_register function was called multiple times

Recommended Action    No action required, software will automatically take corrective action.

Error Message     
 
    
    
   

%HA-REDDRV-7-ROLE_CHANGE Detected role change to [chars] state due to [chars]

Explanation    Detected role change signal.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-7-SHMEM Failed to [chars] share memory region: [chars]

Explanation    Failed to create, open or size share memory region.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-7-SW_ROLE_ERROR Detected software role error my_role: [dec] other_role: [dec]

Explanation    Detected software role error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message     
 
    
    
   

%HA-REDDRV-7-UNEXPECTED Unexpected: [chars]: [chars]

Explanation    An unexpected condition encountered. This is not necessarily an error, but may help with debugging other problems elsewhere!

Recommended Action    Collect system log information. No action is required.