Cisco IOS XR Interface and Hardware Component Debug Command Reference, Release 3.2
PPP Debug Commands on Cisco IOS XR Software
Downloads: This chapterpdf (PDF - 166.0KB) The complete bookPDF (PDF - 2.05MB) | Feedback

PPP Debug Commands on Cisco IOS XR Software

Table Of Contents

PPP Debug Commands on Cisco IOS XR Software

debug ppp authentication

debug ppp negotiation


PPP Debug Commands on Cisco IOS XR Software


This chapter describes the commands used to debug Point-to-Point Protocol (PPP), an encapsulation scheme that can be used on Packet-over-SONET (PoS) interfaces on the Cisco IOS XR software.

debug ppp authentication

To enable debugging of the Link Control Protocol (LCP) session authentication, use the debug ppp authentication command in EXEC mode. To disable debugging, use the no form of this command.

debug ppp authentication [location node-id]

no debug ppp authentication [location node-id]

Syntax Description

location node-id

(Optional) Specifies a location of the line card. The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is that debugging is turned off.

Command Modes

EXEC

Command History

Release
Modification

Release 2.0

This command was introduced on the Cisco CRS-1.

Release 3.0

No modification.

Release 3.2

This command was supported on the Cisco XR 12000 Series Router.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Examples

The following example shows how to use the debug ppp authentication command:

RP/0/RP0/CPU0:router# debug ppp authentication location 0/2/CPU0
 
   
LC/0/2/CPU0:Jun 24 18:00:25.324 : LCP[167]: PO0/2/0/3 CHAP: O CHALLENGE id 93 len 32 from 
"router1"
LC/0/2/CPU0:Jun 24 18:00:25.358 : LCP[167]: PO0/2/0/3 CHAP: I RESPONSE id 93 len 32 from 
"router2"
LC/0/2/CPU0:Jun 24 18:00:25.383 : LCP[167]: PO0/2/0/3 CHAP: I CHALLENGE id 139 len 32 from 
"router2"
LC/0/2/CPU0:Jun 24 18:00:25.489 : LCP[167]: PO0/2/0/3 CHAP: O SUCCESS id 93 len 4 
LC/0/2/CPU0:Jun 24 18:00:25.507 : LCP[167]: PO0/2/0/3 CHAP: O RESPONSE id 139 len 32 from 
"router1"
LC/0/2/CPU0:Jun 24 18:00:25.585 : LCP[167]: PO0/2/0/3 CHAP: I SUCCESS id 139 len 4 
LC/0/2/CPU0:Jun 24 18:00:25.587 : LCP[167]: PO0/2/0/3 PPP: Phase is UP
 
   

Related Commands

Command
Description

debug ppp negotiation

Enables debugging of LCP and Network Control Protocol (NCP) session negotiations.


debug ppp negotiation

To enable debugging of LCP and NCP session negotiations, use the debug ppp negotiation command in EXEC mode. To disable debugging, use the no form of this command.

debug ppp negotiation [location node-id]

no debug ppp negotiation [location node-id]

Syntax Description

location node-id

(Optional) Specifies a location of the line card. The node-id argument is entered in the rack/slot/module notation.


Defaults

The default is that debugging is turned off.

Command Modes

EXEC

Command History

Release
Modification

Release 2.0

This command was introduced on the Cisco CRS-1.

Release 3.0

No modification.

Release 3.2

This command was supported on the Cisco XR 12000 Series Router.


Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.

Examples

The following example shows sample output from the debug ppp negotiation command for LCP and IP Control Protocol (IPCP):

RP/0/RP0/CPU0:router# debug ppp negotiation location 0/2/CPU0
 
   
LC/0/2/CPU0:Jun 24 17:57:39.300 : LCP[167]: PO0/2/0/3 PPP: Phase is ESTABLISHING 
LC/0/2/CPU0:Jun 24 17:57:39.327 : LCP[167]: PO0/2/0/3 LCP: O CONFREQ[Starting] id 1 len 14
LC/0/2/CPU0:Jun 24 17:57:39.327 : LCP[167]: PO0/2/0/3 LCP:    MRU 4470 (0x01041176)
LC/0/2/CPU0:Jun 24 17:57:39.329 : LCP[167]: PO0/2/0/3 LCP:    MagicNumber 0x34b60d89 
(0x050634b60d89)
LC/0/2/CPU0:Jun 24 17:57:39.366 : LCP[167]: PO0/2/0/3 LCP: I CONFACK[REQsent] id 1 len 14
LC/0/2/CPU0:Jun 24 17:57:39.367 : LCP[167]: PO0/2/0/3 LCP:    MRU 4470 (0x01041176)
LC/0/2/CPU0:Jun 24 17:57:39.368 : LCP[167]: PO0/2/0/3 LCP:    MagicNumber 0x34b60d89 
(0x050634b60d89)
LC/0/2/CPU0:Jun 24 17:57:39.787 : LCP[167]: PO0/2/0/3 LCP: I CONFREQ[ACKrcvd] id 8 len 14
LC/0/2/CPU0:Jun 24 17:57:39.787 : LCP[167]: PO0/2/0/3 LCP:    MRU 4470 (0x01041176)
LC/0/2/CPU0:Jun 24 17:57:39.789 : LCP[167]: PO0/2/0/3 LCP:    MagicNumber 0x0c6acbd7 
(0x05060c6acbd7)
LC/0/2/CPU0:Jun 24 17:57:39.789 : LCP[167]: PO0/2/0/3 LCP: O CONFACK[ACKrcvd] id 8 len 14
LC/0/2/CPU0:Jun 24 17:57:39.790 : LCP[167]: PO0/2/0/3 LCP:    MRU 4470 (0x01041176)
LC/0/2/CPU0:Jun 24 17:57:39.791 : LCP[167]: PO0/2/0/3 LCP:    MagicNumber 0x0c6acbd7 
(0x05060c6acbd7)
LC/0/2/CPU0:Jun 24 17:57:39.795 : LCP[167]: PO0/2/0/3 LCP: State is Open LC/0/2/CPU0:Jun 
24 17:57:39.799 : LCP[167]: PO0/2/0/3 PPP: Phase is UP
 
   
LC/0/2/CPU0:Jun 24 17:58:46.869 : IPCP[147]: PO0/2/0/3 IPCP: O CONFREQ[Starting] id 1 len 
10
LC/0/2/CPU0:Jun 24 17:58:46.870 : IPCP[147]: PO0/2/0/3 IPCP:    Address 12.0.0.1 
(0x03060c000001)
LC/0/2/CPU0:Jun 24 17:58:46.883 : IPCP[147]: PO0/2/0/3 IPCP: I CONFREQ[REQsent] id 2 len 
10
LC/0/2/CPU0:Jun 24 17:58:46.884 : IPCP[147]: PO0/2/0/3 IPCP:    Address 12.0.0.2 
(0x03060c000002)
LC/0/2/CPU0:Jun 24 17:58:46.886 : IPCP[147]: PO0/2/0/3 IPCP: O CONFACK[REQsent] id 2 len 
10
LC/0/2/CPU0:Jun 24 17:58:46.888 : IPCP[147]: PO0/2/0/3 IPCP:    Address 12.0.0.2 
(0x03060c000002)
LC/0/2/CPU0:Jun 24 17:58:46.892 : IPCP[147]: PO0/2/0/3 IPCP: I CONFACK[ACKsent] id 1 len 
10
LC/0/2/CPU0:Jun 24 17:58:46.893 : IPCP[147]: PO0/2/0/3 IPCP:    Address 12.0.0.1 
(0x03060c000001)
LC/0/2/CPU0:Jun 24 17:58:46.897 : IPCP[147]: PO0/2/0/3 IPCP: State is Open LC/0/2/CPU0:Jun 
24 17:58:46.907 : IPCP[147]: PO0/2/0/3 IPCP: Install adjacency 0XFF030021
 
   

Related Commands

Command
Description

debug ppp authentication

Enables debugging of LCP session authentication.