X.25 Data Display Trace
ErrorMessage : Error while constructing the Hinav

null
Downloads: This chapterpdf (PDF - 114.0KB) | Feedback

X.25 Data Display Trace

Table Of Contents

X.25 Data Display Trace

Contents

Displaying the Contents of X.25 Packets

Additional References

Related Documents

Standards

Technical Assistance

Feature Information for X.25 Data Display Trace


X.25 Data Display Trace


The X.25 Data Display Trace feature enhances the Cisco IOS debugging capability for X.25. This feature enables an authorized user to display the entire X.25-encoded traffic stream, including user data, for those packets specified by an X.25 debug command.

Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Contents

Displaying the Contents of X.25 Packets

Additional References

Feature Information for X.25 Data Display Trace

Displaying the Contents of X.25 Packets

To augment the reporting of X.25 traffic information to include the contents of the X.25 packets, use the commands listed in the following task. Note that an entry of the debug x25, debug x25 interface, debug x25 vc, or debug x25 xot commands will override any prior entry of any of these commands.


Caution The reported X.25 packet information may contain sensitive data; for example, clear-text account identities and passwords. The network access policies and router configuration should be controlled appropriately to address this risk.


Caution The X.25 debug commands can generate large amounts of debugging output. If logging of debug output to the router console is enabled (the default condition), this output may fill the console buffer, preventing the router from processing packets until the contents of the console buffer have been printed.

SUMMARY STEPS

1. enable

2. debug x25 [only | cmns | xot] [events | all] [dump]

3. debug x25 interface {serial-interface | cmns-interface [mac mac-address]} [vc number] [events | all] [dump]

4. debug x25 vc number [events | all] [dump]

5. debug x25 xot [remote ip-address [port number]] [local ip-address [port number]] [events | all] [dump]

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

debug x25 [only | cmns | xot] [events | all] [dump]

Example:

Router# debug x25 events

Displays information about all X.25 traffic or a specific X.25 service class.

Use the dump keyword to display the contents, including user data, of X.25 packets.

Step 3 

debug x25 interface {serial-interface | cmns-interface [mac mac-address]} [vc number] [events | all] [dump]

Example:

Router# debug x25 interface serial 0 dump

Displays information about X.25, Annex G or CMNS contexts or virtual circuits that occur on the identified interface.

CMNS reports may be restricted to packets occurring on the interface with the specified remote host.

Use the dump keyword to display the contents, including user data, of X.25 packets.

Step 4 

debug x25 vc number [events | all] [dump]

Example:

Router# debug x25 vc 1 events

Displays information about traffic for all virtual circuits that use a given number.

Use the dump keyword to display the contents, including user data, of X.25 packets.

Step 5 

debug x25 xot [remote ip-address [port number]] [local ip-address [port number]] [events | all] [dump]

Example:

Router# debug x25 xot remote 10.0.155.71 port 1998

Displays information about traffic to or from a specific X.25 over TCP (XOT) host.

Use the dump keyword to display the contents, including user data, of X.25 packets.

Additional References

Related Documents

Related Topic
Document Title

X.25 configuration tasks

Cisco IOS Wide-Area Networking Configuration Guide, Release 12.3

X.25 commands

Cisco IOS Wide-Area Networking Command Reference, Release 12.3


Standards

Standards
Title

ITU-T 1993 Recommendation X.25

Interface between DTE and DCE for terminals operating in the packet mode and connected to public data networks by dedicated circuit


Technical Assistance

Description
Link

Technical Assistance Center (TAC) home page, containing 30,000 pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/public/support/tac/home.shtml


Feature Information for X.25 Data Display Trace

Table 1 lists the release history for this feature.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.


Table 1 Feature Information for X.25 Data Display Trace 

Feature Name
Releases
Feature Information

X.25 Data Display Trace

12.3(2)T

The X.25 Data Display Trace feature enhances the Cisco IOS debugging capability for X.25. This feature enables an authorized user to display the entire X.25-encoded traffic stream, including user data, for those packets specified by an X.25 debug command.

In Cisco IOS Release 12.3(2)T, this feature was introduced

The following commands were introduced or modified: debug x25, debug x25 interface, debug x25 vc.