This documentation has been moved
Verifying Analog and Digital Voice-Port Configurations
Downloads: This chapterpdf (PDF - 187.0KB) | Feedback

Verifying Analog and Digital Voice-Port Configurations

Table Of Contents

Verifying Analog and Digital Voice-Port Configurations

Information About Verifying Analog and Digital Voice-Port Configurations

How to Verify Analog and Digital Voice-Port Configurations

Examples

show voice port summary Command: Examples

show voice port Command: Examples

show controller Command: Examples

show voice dsp Command: Examples

show voice call summary Command: Examples

show call active voice Command: Example

show call history voice Command: Example


Verifying Analog and Digital Voice-Port Configurations


This chapter describes some basic procedures and specific CLI commands you can use to verify the set up and configuration of the analog and digital voice ports on the routers in your voice network.

Information About Verifying Analog and Digital Voice-Port Configurations

After configuring the voice ports on your router, there are two simple verifications you can use to check the operation of the telephony handset. There are also eight CLI commands you can use to verify proper operation of the configuration.

How to Verify Analog and Digital Voice-Port Configurations

To verify the operability of the analog and digital voice-port configurations on your voice network, complete the following tasks.

SUMMARY STEPS

1. Check for a dial tone.

2. Check for DTMF detection.

3. show voice port summary

4. show voice port

5. show running-config

6. show controller

7. show voice dsp

8. show voice call summary

9. show call active voice

10. show call history voice

DETAILED STEPS


Step 1 Check for a dial tone.

Pick up the handset of an attached telephony device and check for a dial tone.

Step 2 Check for Dual-Tone Multifrequency (DTMF) detection.

If you have dial tone, check for DTMF detection. If the dial tone stops when you dial a digit, then the voice port is probably configured properly.

Step 3 show voice port summary

Use this command to identify the port numbers of voice interfaces installed in your router. For examples of the output, see the "Examples" section.

Step 4 show voice port

Use this command to verify voice-port parameter settings. Refer to Table 2 for the appropriate syntax for your platform. For sample output, see the "show voice port Command: Examples" section.

Table 2 Show Voice Port Command Syntax

Platform
Voice Port Type
Command Syntax

Cisco 1750

Analog

show voice port [slot/port | summary]

Cisco 2600 series
Cisco 3600 series
Cisco 3700 series

Analog

show voice port [slot/port | summary]

Digital

show voice port [slot/port:ds0-group-number | summary]

Cisco MC3810

Analog

show voice port [slot/port | summary]

Digital

show voice port [slot:ds0-group-number | summary]

Cisco AS5300

Digital

show voice port [controller:{ds0-group-number | D}] [summary]

Cisco AS5350
Cisco AS5400
Cisco AS5850

Digital

show voice port [slot/controller:{ds0-group-number | D}] [summary]

Cisco AS5800

Digital

show voice port {shelf/slot/port:ds0-group-number}

Cisco 7200 series

Digital

show voice port {slot/port-adapter:ds0-group-number}

Cisco 7500 series

Digital

show voice port {slot/port-adapter/slot:ds0-group-number}


Step 5 show running-config

Use this command to verify the codec complexity setting for digital T1/E1 connections. If medium complexity is specified for the voice card, the codec complexity command is not displayed. If high complexity is specified, the codec complexity high command is displayed. The following example shows output when high complexity is specified:

Router# show running-config
.
.
.
hostname router-alpha 
 
voice-card 0
 codec complexity high 
.
.
.

Step 6 show controller

Use this command to verify that the digital T1/E1 controller is up and that no alarms have been reported, and to display information about clock sources and other controller settings. For output examples, see the "show controller Command: Examples" section.

Router# show controller {t1 | e1} controller-number

Step 7 show voice dsp

Use this command to display voice-channel configuration information for all DSP channels. For output examples, see the "show voice dsp Command: Examples" section.

Router# show voice dsp

Step 8 show voice call summary

Use this command to verify the call status for all voice ports. For output examples, see the "show voice call summary Command: Examples" section.

Router# show voice call summary

Step 9 show call active voice

Use this command to display the contents of the active call table, which shows all of the calls currently connected through the router or concentrator. For output examples, see the "show call active voice Command: Example" section.

Router# show call active voice

Step 10 show call history voice

Use this command to display the contents of the call history table. To limit the display to the most recent calls connected through this router, use the last keyword and define the number of calls to display with the number argument. To limit the display to a shortened version of the call history table, use the brief keyword. For output examples, see the "show call history voice Command: Example" section.

Router# show call history voice [last | number | brief]


Examples

This section contains output examples for the following commands on different platforms and for different configurations:

show voice port summary Command: Examples

show voice port Command: Examples

show controller Command: Examples

show voice dsp Command: Examples

show voice call summary Command: Examples

show call active voice Command: Example

show call history voice Command: Example

show voice port summary Command: Examples

Cisco 3640 Router Analog Voice Port

The following output is from a Cisco 3640 router:

Router# show voice port summary
                                  IN      OUT
PORT   CH SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
====== == ========== ===== ==== ======== ======== ==
2/0/0  -- e&m-wnk    up    dorm idle     idle     y 
2/0/1  -- e&m-wnk    up    dorm idle     idle     y 
2/1/0  -- fxs-ls     up    dorm on-hook  idle     y 
2/1/1  -- fxs-ls     up    dorm on-hook  idle     y 

Cisco MC3810 Digital Voice Port

The following output is from a Cisco MC3810:

Router# show voice port summary
                                  IN      OUT
PORT   CH SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
====== == ========== ===== ==== ======== ======== ==
0:17   18 fxo-ls     down  down idle     on-hook  y
0:18   19 fxo-ls     up    dorm idle     on-hook  y
0:19   20 fxo-ls     up    dorm idle     on-hook  y
0:20   21 fxo-ls     up    dorm idle     on-hook  y
0:21   22 fxo-ls     up    dorm idle     on-hook  y
0:22   23 fxo-ls     up    dorm idle     on-hook  y
0:23   24 e&m-imd    up    dorm idle     idle     y
1/1    -- fxs-ls     up    dorm on-hook  idle     y
1/2    -- fxs-ls     up    dorm on-hook  idle     y
1/3    -- e&m-imd    up    dorm idle     idle     y
1/4    -- e&m-imd    up    dorm idle     idle     y
1/5    -- fxo-ls     up    dorm idle     on-hook  y
1/6    -- fxo-ls     up    dorm idle     on-hook  y

show voice port Command: Examples

Cisco 3600 Series Router Analog E&M Voice Port

The following output is from a Cisco 3600 series router analog E&M voice port:

Router# show voice port 1/0

E&M Slot is 1, Sub-unit is 0, Port is 0
 Type of VoicePort is E&M
 Operation State is unknown
 Administrative State is unknown
 The Interface Down Failure Cause is 0
 Alias is NULL
 Noise Regeneration is disabled
 Non Linear Processing is disabled
 Music On Hold Threshold is Set to 0 dBm
 In Gain is Set to 0 dB
 Out Attenuation is Set to 0 dB
 Echo Cancellation is disabled
 Echo Cancel Coverage is set to 16ms
 Connection Mode is Normal
 Connection Number is 
 Initial Time Out is set to 0 s
 Interdigit Time Out is set to 0 s
 Analog Info Follows:
 Region Tone is set for northamerica
 Currently processing none
 Maintenance Mode Set to None (not in mtc mode)
 Number of signaling protocol errors are 0
 
 Voice card specific Info Follows:
 Signal Type is wink-start
 Operation Type is 2-wire
 Impedance is set to 600r Ohm
 E&M Type is unknown
 Dial Type is dtmf
 In Seizure is inactive
 Out Seizure is inactive
 Digit Duration Timing is set to 0 ms
 InterDigit Duration Timing is set to 0 ms
 Pulse Rate Timing is set to 0 pulses/second
 InterDigit Pulse Duration Timing is set to 0 ms
 Clear Wait Duration Timing is set to 0 ms
 Wink Wait Duration Timing is set to 0 ms
 Wink Duration Timing is set to 0 ms
 Delay Start Timing is set to 0 ms
 Delay Duration Timing is set to 0 ms

Cisco 3600 Series Router Analog FXS Voice Port

The following output is from a Cisco 3600 series router analog Foreign Exchange Service (FXS) voice port:

Router# show voice port 1/2

Voice port 1/2 Slot is 1, Port is 2
 Type of VoicePort is FXS
 Operation State is UP
 Administrative State is UP
 No Interface Down Failure
 Description is not set
 Noise Regeneration is enabled
 Non Linear Processing is enabled
 In Gain is Set to 0 dB
 Out Attenuation is Set to 0 dB
 Echo Cancellation is enabled
 Echo Cancel Coverage is set to 8 ms
 Connection Mode is normal
 Connection Number is not set
 Initial Time Out is set to 10 s
 Interdigit Time Out is set to 10 s
 Coder Type is g729ar8
 Companding Type is u-law
 Voice Activity Detection is disabled
 Ringing Time Out is 180 s
 Wait Release Time Out is 30 s
 Nominal Playout Delay is 80 milliseconds
 Maximum Playout Delay is 160 milliseconds

 Analog Info Follows:
 Region Tone is set for northamerica
 Currently processing Voice
 Maintenance Mode Set to None (not in mtc mode)
 Number of signaling protocol errors are 0
 Impedance is set to 600r Ohm
 Analog interface A-D gain offset = -3 dB 
 Analog interface D-A gain offset = -3 dB 
 Voice card specific Info Follows:
 Signal Type is loopStart
 Ring Frequency is 20 Hz
 Hook Status is On Hook
 Ring Active Status is inactive
 Ring Ground Status is inactive
 Tip Ground Status is active
 Digit Duration Timing is set to 100 ms
 InterDigit Duration Timing is set to 100 ms
 Ring Cadence are [20 40] * 100 msec
 InterDigit Pulse Duration Timing is set to 500 ms

Cisco 3600 Series Router Digital E&M Voice Port

The following output is from a Cisco 3600 series router digital E&M voice port:

Router# show voice port 1/0:1
 
receEive and transMit Slot is 1, Sub-unit is 0, Port is 1
 Type of VoicePort is E&M
 Operation State is DORMANT
 Administrative State is UP
 No Interface Down Failure
 Description is not set
 Noise Regeneration is enabled
 Non Linear Processing is enabled
 Music On Hold Threshold is Set to -38 dBm
 In Gain is Set to 0 dB
 Out Attenuation is Set to 0 dB
 Echo Cancellation is enabled
 Echo Cancel Coverage is set to 8 ms
 Connection Mode is normal
 Connection Number is not set
 Initial Time Out is set to 10 s
 Interdigit Time Out is set to 10 s
 Region Tone is set for US

Cisco AS5300 T1 CAS Voice Port

The following output is from a Cisco AS5300 T1 channel-associated signaling (CAS) voice port:

Router# show voice port
 
DS0 Group 1:0 - 1:0
 Type of VoicePort is CAS
 Operation State is DORMANT
 Administrative State is UP
 No Interface Down Failure
 Description is not set
 Noise Regeneration is enabled
 Non Linear Processing is enabled
 Music On Hold Threshold is Set to -38 dBm
 In Gain is Set to 0 dB
 Out Attenuation is Set to 0 dB
 Echo Cancellation is enabled
 Echo Cancel Coverage is set to 8 ms
 Playout-delay Mode is set to default
 Playout-delay Nominal is set to 60 ms
 Playout-delay Maximum is set to 200 ms
 Connection Mode is normal
 Connection Number is not set
 Initial Time Out is set to 10 s
 Interdigit Time Out is set to 10 s
 Call-Disconnect Time Out is set to 60 s
 Ringing Time Out is set to 180 s
 Companding Type is u-law
 Region Tone is set for US
 Wait Release Time Out is 30 s
 Station name None, Station number None
 
 Voice card specific Info Follows:
 
 DS0 channel specific status info:
                                IN      OUT
    PORT   CH SIG-TYPE   OPER STATUS   STATUS    TIP     RING

Cisco 7200 Series Router Digital E&M Voice Port

The following output is from a Cisco 7200 series router digital E&M voice port:

Router# show voice port 1/0:1

receEive and transMit Slot is 1, Sub-unit is 0, Port is 1  << voice-port 1/0:1

 Type of VoicePort is E&M

 Operation State is DORMANT

 Administrative State is UP

 No Interface Down Failure
 Description is not set
 Noise Regeneration is enabled
 Non Linear Processing is enabled
 Music On Hold Threshold is Set to -38 dBm
 In Gain is Set to 0 dB

 Out Attenuation is Set to 0 dB

 Echo Cancellation is enabled

 Echo Cancel Coverage is set to 8 ms
 Connection Mode is normal
 Connection Number is not set
 Initial Time Out is set to 10 s

 Interdigit Time Out is set to 10 s

 Region Tone is set for US

show controller Command: Examples

Cisco 3600 Series Router T1 Controller

The following output is from a Cisco 3600 series router with a T1 controller:

Router# show controller T1 1/1/0

T1 1/0/0 is up.
  Applique type is Channelized T1
  Cablelength is long gain36 0db
  No alarms detected.
  alarm-trigger is not set
  Framing is ESF, Line Code is B8ZS, Clock Source is Line.
  Data in current interval (180 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Cisco MC3810 E1 Controller

The following output is from a Cisco MC3810 with an E1 controller:

Router# show controller e1 1/0

E1 1/0 is up.
  Applique type is Channelized E1
  Cablelength is short 133
  Description: E1 WIC card Alpha
  No alarms detected.
  Framing is CRC4, Line Code is HDB3, Clock Source is Line Primary.
  Data in current interval (1 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Cisco AS5800 T1 Controller

The following output is from a Cisco AS5800 with a T1 controller:

Router# show controller t1 2

 T1 2 is up.
   No alarms detected.
   Version info of slot 0:  HW: 2, Firmware: 16, PLD Rev: 0
 
 Manufacture Cookie Info:
  EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x42,
  Board Hardware Version 1.0, Item Number 73-2217-4,
  Board Revision A0, Serial Number 06467665,
  PLD/ISP Version 0.0, Manufacture Date 14-Nov-1997.
 
   Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
   Data in current interval (269 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
      0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

show voice dsp Command: Examples

Digital Voice Port on a Cisco 3640

The following output is from a Cisco 3640 router when a digital voice port is configured:

Router# show voice dsp

TYPE DSP CH CODEC    VERS STATE STATE   RST AI PORT    TS ABORT   TX/RX-PAK-CNT
==== === == ======== ==== ===== ======= === == ======= == ===== ===============
C549 010 00 g729r8    3.3 busy  idle      0  0 1/015   1     0     67400/85384
         01 g729r8     .8 busy  idle      0  0 1/015   7     0     67566/83623
         02 g729r8        busy  idle      0  0 1/015  13     0     65675/81851
         03 g729r8        busy  idle      0  0 1/015  20     0     65530/83610
C549 011 00 g729r8    3.3 busy  idle      0  0 1/015   2     0     66820/84799
         01 g729r8     .8 busy  idle      0  0 1/015   8     0     59028/66946
         02 g729r8        busy  idle      0  0 1/015  14     0     65591/81084
         03 g729r8        busy  idle      0  0 1/015  21     0     66336/82739
C549 012 00 g729r8    3.3 busy  idle      0  0 1/015   3     0     59036/65245
         01 g729r8     .8 busy  idle      0  0 1/015   9     0     65826/81950
         02 g729r8        busy  idle      0  0 1/015  15     0     65606/80733
         03 g729r8        busy  idle      0  0 1/015  22     0     65577/83532
C549 013 00 g729r8    3.3 busy  idle      0  0 1/015   4     0     67655/82974
         01 g729r8     .8 busy  idle      0  0 1/015  10     0     65647/82088
         02 g729r8        busy  idle      0  0 1/015  17     0     66366/80894
         03 g729r8        busy  idle      0  0 1/015  23     0     66339/82628
C549 014 00 g729r8    3.3 busy  idle      0  0 1/015   5     0     68439/84677
         01 g729r8     .8 busy  idle      0  0 1/015  11     0     65664/81737
         02 g729r8        busy  idle      0  0 1/015  18     0     65607/81820
         03 g729r8        busy  idle      0  0 1/015  24     0     65589/83889
C549 015 00 g729r8    3.3 busy  idle      0  0 1/015   6     0     66889/83331
         01 g729r8     .8 busy  idle      0  0 1/015  12     0     65690/81700
         02 g729r8        busy  idle      0  0 1/015  19     0     66422/82099
         03 g729r8        busy  idle      0  0 1/015  25     0     65566/83852

Router# show voice dsp

TYPE DSP CH CODEC    VERS STATE STATE   RST AI PORT    TS ABORT   TX/RX-PAK-CNT
==== === == ======== ==== ===== ======= === == ======= == ===== ===============
C549 007 00 {medium}  3.3 IDLE  idle      0  0 1/0:1    4     0             0/0
                      .13
C549 008 00 {medium}  3.3 IDLE  idle      0  0 1/0:1    5     0             0/0
                      .13
C549 009 00 {medium}  3.3 IDLE  idle      0  0 1/0:1    6     0             0/0
                      .13
C549 010 00 {medium}  3.3 IDLE  idle      0  0 1/0:1    7     0             0/0
                      .13
C549 011 00 {medium}  3.3 IDLE  idle      0  0 1/0:1    8     0             0/0
                      .13
C549 012 00 {medium}  3.3 IDLE  idle      0  0 1/0:1    9     0             0/0
                      .13
C542 001 01 g711ulaw  3.3 IDLE  idle      0  0 2/0/0          0         512/519
                      .13
C542 002 01 g711ulaw  3.3 IDLE  idle      0  0 2/0/1          0         505/502
                      .13
C542 003 01 g711alaw  3.3 IDLE  idle      0  0 2/1/0          0     28756/28966
                      .13
C542 004 01 g711ulaw  3.3 IDLE  idle      0  0 2/1/1          0         834/838
                      .13

show voice call summary Command: Examples

Cisco MC3810 Analog Voice Port

The following output is from a Cisco MC3810:

Router# show voice call summary

PORT      CODEC    VAD VTSP STATE            VPM STATE
========= ======== === ===================== ========================
1/1       g729r8    y  S_CONNECT             FXSLS_CONNECT            
1/2       -         -  -                     FXSLS_ONHOOK             
1/3       -         -  -                     EM_ONHOOK                
1/4       -         -  -                     EM_ONHOOK                
1/5       -         -  -                     FXOLS_ONHOOK             
1/6       -         -  -                     FXOLS_ONHOOK        

Cisco 3600 Series Router Digital Voice Port

The following output is from a Cisco 3600 series router:

Router# show voice call summary

PORT      CODEC    VAD VTSP STATE            VPM STATE
========= ======== === ===================== ========================
1/015.1  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.2  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.3  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.4  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.5  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.6  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.7  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.8  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.9  g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.10 g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.11 g729r8    y  S_CONNECT             S_TSP_CONNECT            
1/015.12 g729r8    y  S_CONNECT             S_TSP_CONNECT            

show call active voice Command: Example

Cisco 7200 Series Router

The following output is from a Cisco 7200 series router:

Router# show call active voice

GENERIC:
SetupTime=94523746 ms
Index=448
PeerAddress=##73072

PeerSubAddress=
PeerId=70000

PeerIfIndex=37
LogicalIfIndex=0
ConnectTime=94524043
DisconectTime=94546241
CallOrigin=1

ChargedUnits=0
InfoType=2
TransmitPackets=6251
TransmitBytes=125020
ReceivePackets=3300
ReceiveBytes=66000
VOIP:
ConnectionId[0x142E62FB 0x5C6705AF 0x0 0x385722B0]
RemoteIPAddress=172.16.235.18

RemoteUDPPort=16580

RoundTripDelay=29 ms

SelectedQoS=best-effort
tx_DtmfRelay=inband-voice
SessionProtocol=cisco
SessionTarget=ipv4:172.16.235.18
OnTimeRvPlayout=63690
GapFillWithSilence=0 ms

GapFillWithPrediction=180 ms

GapFillWithInterpolation=0 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=70 ms
LoWaterPlayoutDelay=30 ms
ReceiveDelay=40 ms
LostPackets=0 ms

EarlyPackets=1 ms

LatePackets=18 ms

VAD = disabled

CoderTypeRate=g729r8

CodecBytes=20

cvVoIPCallHistoryIcpif=0
SignalingType=cas

show call history voice Command: Example

Cisco 7200 Series Router

The following output is from a Cisco 7200 series router:

Router# show call history voice

GENERIC:
SetupTime=94893250 ms
Index=450
PeerAddress=##52258

PeerSubAddress=
PeerId=50000

PeerIfIndex=35
LogicalIfIndex=0
DisconnectCause=10

DisconnectText=normal call clearing.

ConnectTime=94893780
DisconectTime=95015500
CallOrigin=1

ChargedUnits=0
InfoType=2
TransmitPackets=32258
TransmitBytes=645160
ReceivePackets=20061
ReceiveBytes=401220
VOIP:
ConnectionId[0x142E62FB 0x5C6705B3 0x0 0x388F851C]
RemoteIPAddress=172.16.235.18

RemoteUDPPort=16552

RoundTripDelay=23 ms

SelectedQoS=best-effort
tx_DtmfRelay=inband-voice
SessionProtocol=cisco
SessionTarget=ipv4:172.16.235.18
OnTimeRvPlayout=398000
GapFillWithSilence=0 ms

GapFillWithPrediction=1440 ms

GapFillWithInterpolation=0 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=97 ms
LoWaterPlayoutDelay=30 ms
ReceiveDelay=49 ms
LostPackets=1 ms
EarlyPackets=1 ms

LatePackets=132 ms

VAD = disabled

CoderTypeRate=g729r8

CodecBytes=20
cvVoIPCallHistoryIcpif=0

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)