This documentation has been moved
AAA Dead-Server Detection
Downloads: This chapterpdf (PDF - 145.0KB) The complete bookPDF (PDF - 3.46MB) | Feedback

AAA Dead-Server Detection

Table Of Contents

AAA Dead-Server Detection

Finding Feature Information

Contents

Prerequisites for AAA Dead-Server Detection

Restrictions for AAA Dead-Server Detection

Information About AAA Dead-Server Detection

Criteria for Marking a RADIUS Server As Dead

How to Configure AAA Dead-Server Detection

Configuring AAA Dead-Server Detection

Troubleshooting Tips

Verifying AAA Dead-Server Detection

Configuration Examples for AAA Dead-Server Detection

Configuring AAA Dead-Server Detection: Example

debug aaa dead-criteria transactions Command: Example

show aaa dead-criteria Command: Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for AAA Dead-Server Detection


AAA Dead-Server Detection


First Published: February 13, 2004
Last Updated: September 10, 2010

The AAA Dead-Server Detection feature allows you to configure the criteria to be used to mark a RADIUS server as dead. If no criteria are explicitly configured, the criteria are computed dynamically on the basis of the number of outstanding transactions. Using this feature will result in less deadtime and quicker packet processing.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for AAA Dead-Server Detection" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp. An account on Cisco.com is not required.

Contents

Prerequisites for AAA Dead-Server Detection

Restrictions for AAA Dead-Server Detection

Information About AAA Dead-Server Detection

How to Configure AAA Dead-Server Detection

Configuration Examples for AAA Dead-Server Detection

Additional References

Feature Information for AAA Dead-Server Detection

Prerequisites for AAA Dead-Server Detection

You must have access to a RADIUS server.

You should be familiar with configuring a RADIUS server.

You should be familiar with configuring authentication, authorization, and accounting (AAA).

Before a server can be marked as dead, you must first configure the radius-server deadtime command. If this command is not configured, even if the criteria are met for the server to be marked as dead, the server state will be the "up" state.

Restrictions for AAA Dead-Server Detection

Original transmissions are not counted in the number of consecutive timeouts that must occur on the router before the server is marked as dead—only the number of retransmissions are counted.

Information About AAA Dead-Server Detection

To configure the AAA Dead-Server Detection feature, you should understand the following concept:

Criteria for Marking a RADIUS Server As Dead

Criteria for Marking a RADIUS Server As Dead

The AAA Dead-Server Detection feature allows you to determine the criteria that are used to mark a RADIUS server as dead. That is, you can configure the minimum amount of time, in seconds, that must elapse from the time that the router last received a valid packet from the RADIUS server to the time the server is marked as dead. If a packet has not been received since the router booted, and there is a timeout, the time criterion will be treated as though it has been met.

In addition, you can configure the number of consecutive timeouts that must occur on the router before the RADIUS server is marked as dead. If the server performs both authentication and accounting, both types of packets are included in the number. Improperly constructed packets are counted as though they are timeouts. Only retransmissions are counted, not the initial transmission. (Each timeout causes one retransmission to be sent.)


Note Both the time criterion and the tries criterion must be met for the server to be marked as dead.


The RADIUS dead-server detection configuration will result in the prompt detection of RADIUS servers that have stopped responding. This configuration will also result in the avoidance of servers being improperly marked as dead when they are "swamped" (responding slowly) and the avoidance of the state of servers being rapidly changed from dead to live to dead again. This prompt detection of nonresponding RADIUS servers and the avoidance of swamped and dead-to-live-to-dead-again servers will result in less deadtime and quicker packet processing.

How to Configure AAA Dead-Server Detection

This section contains the following procedures:

Configuring AAA Dead-Server Detection (required)

Verifying AAA Dead-Server Detection (optional)

Configuring AAA Dead-Server Detection

To configure AAA Dead-Server Detection, perform the following steps.

SUMMARY STEPS

1. enable

2. configure terminal

3. aaa new-model

4. radius-server deadtime minutes

5. radius-server dead-criteria [time seconds] [tries number-of-tries]

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

aaa new-model

Example:

Router (config)# aaa new-model

Enables the AAA access control model.

Step 4 

radius-server deadtime minutes

Example:

Router (config)# radius-server deadtime 5

Improves RADIUS response times when some servers might be unavailable and causes the unavailable servers to be skipped immediately.

Step 5 

radius-server dead-criteria [time seconds] [tries number-of-tries]

Example:

Router (config)# radius-server dead-criteria time 5 tries 4

Forces one or both of the criteria—used to mark a RADIUS server as dead—to be the indicated constant.

Troubleshooting Tips

After you have configured AAA Dead-Server Detection, you should verify your configuration using the show running-config command. This verification is especially important if you have used the no form of the radius-server dead-criteria command. The output of the show running-config command must show the same values in the "Dead Criteria Details" field that you configured using the radius-server dead-criteria command.

Verifying AAA Dead-Server Detection

To verify your AAA Dead-Server Detection configuration, perform the following steps. The show and debug commands may be used in any order.

SUMMARY STEPS

1. enable

2. debug aaa dead-criteria transactions

3. show aaa dead-criteria

4. show aaa servers

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

debug aaa dead-criteria transactions

Example:

Router# debug aaa dead-criteria transactions

Displays AAA dead-criteria transaction values.

Step 3 

show aaa dead-criteria

Example:

Router# show aaa dead-criteria

Displays dead-criteria information for a AAA server.

Step 4 

show aaa servers [private | public]

Example:

Router# show aaa server private

Displays the status and number of packets that are sent to and received from all public and private authentication, authorization, and accounting (AAA) RADIUS servers.

The private keyword optionally displays the AAA servers only.

The public keyword optionally displays the AAA servers only.

Configuration Examples for AAA Dead-Server Detection

This section provides the following configuration examples:

Configuring AAA Dead-Server Detection: Example

debug aaa dead-criteria transactions Command: Example

show aaa dead-criteria Command: Example

Configuring AAA Dead-Server Detection: Example

The following example shows that the router will be considered dead after 5 seconds and four tries:

Router (config)# aaa new-model
Router (config)# radius-server deadtime 5
Router (config)# radius-server dead-criteria time 5 tries 4

debug aaa dead-criteria transactions Command: Example

The following output example shows dead-criteria transaction information for a particular server group:

Router# debug aaa dead-criteria transactions

AAA Transaction debugs debugging is on

*Nov 14 23:44:17.403: AAA/SG/TRANSAC: Computed Retransmit Tries: 22, Current Max Tries: 22
*Nov 14 23:44:17.403: AAA/SG/TRANSAC: Computed Dead Detect Interval: 25s, Current Max 
Interval: 25s
*Nov 14 23:44:17.403: AAA/SG/TRANSAC: Estimated Outstanding Transactions: 6, Current Max 
Transactions: 6

show aaa dead-criteria Command: Example

The following output example shows that dead-server-detection information has been requested for a RADIUS server at the IP address 172.19.192.80:

Router# show aaa dead-criteria radius 172.19.192.80 radius

RADIUS Server Dead Criteria:
=============================
Server Details: 
    Address : 172.19.192.80
    Auth Port : 1645
    Acct Port : 1646
Server Group : radius
Dead Criteria Details:
    Configured Retransmits : 62
    Configured Timeout : 27
    Estimated Outstanding Transactions: 5
    Dead Detect Time : 25s
    Computed Retransmit Tries: 22
    Statistics Gathered Since Last Successful Transaction
=====================================================
Max Computed Outstanding Transactions: 5
Max Computed Dead Detect Time: 25s
Max Computed Retransmits : 22

Additional References

The following sections provide references related to the AAA Dead-Server Detection feature.

Related Documents

Related Topic
Document Title

Configuring RADIUS

"Configuring RADIUS" feature module.

Configuring AAA

"Configuring Authentication"

"Configuring Authorization"

"Configuring Accounting"

Security commands

Cisco IOS Security Command Reference


Standards

Standards
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


MIBs

MIBs
MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFCs
Title

RFC 2865

Remote Authentication Dial In User Service (RADIUS)


Technical Assistance

Description
Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport


Feature Information for AAA Dead-Server Detection

Table 1 lists the release history for this feature.

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS, Catalyst OS, and Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 1 lists only the Cisco IOS software release that introduced support for a given feature in a given Cisco IOS software release train. Unless noted otherwise, subsequent releases of that Cisco IOS software release train also support that feature.


Table 1 Feature Information for AAA Dead-Server Detection

Feature Name
Releases
Feature Information

AAA Dead-Server Detection

12.3(6)
12.3(7)T
Cisco IOS XE Release 2.1
Cisco IOS XE 3.1.0SG

Allows you to configure the criteria to be used to mark a RADIUS server as dead.

The following commands were introduced or modified: debug aaa dead-criteria transactions, radius-server dead-criteria, show aaa dead-criteria, show aaa servers.