This documentation has been moved
SNMP Support for VLAN Subinterfaces
Downloads: This chapterpdf (PDF - 132.0KB) The complete bookPDF (PDF - 3.01MB) | Feedback

SNMP Support for VLAN Subinterfaces

Table Of Contents

SNMP Support for VLAN Subinterfaces

Finding Feature Information

Contents

Information About SNMP Support for VLAN Subinterfaces

Benefits

Supported Platforms

How to SNMP Support for VLAN Subinterfaces

Enabling the SNMP Agent on VLAN Subinterfaces

Configuration Examples for SNMP Support for VLAN Subinterfaces

Example: Enabling the SNMP Agent for VLAN Subinterfaces

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for SNMP Support for VLAN Subinterfaces


SNMP Support for VLAN Subinterfaces


First Published: October 15, 2007
Last Updated: April 15, 2011

This feature module describes the SNMP Support for VLAN Subinterfaces feature. It includes information on the benefits of the new feature, supported platforms, supported standards, and the commands necessary to configure the SNMP Support for VLAN Subinterfaces feature.

The SNMP Support for VLAN Subinterfaces feature provides mib-2 interfaces sparse table support for Fast Ethernet subinterfaces. This enhancement is similar to the functionality supported in Frame Relay subinterfaces.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for SNMP Support for VLAN Subinterfaces" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

Information About SNMP Support for VLAN Subinterfaces

How to SNMP Support for VLAN Subinterfaces

Configuration Examples for SNMP Support for VLAN Subinterfaces

Additional References

Feature Information for SNMP Support for VLAN Subinterfaces

Information About SNMP Support for VLAN Subinterfaces

Benefits

Supported Platforms

Benefits

Sparse table support for the interfaces table on Fast Ethernet subinterfaces provides customers accustomed to Frame Relay subinterfaces the same functionality.

Supported Platforms

Cisco 2600 series

Cisco 3600 series

Cisco 4000-m series

Cisco 7200 series

Cisco 7500 series

How to SNMP Support for VLAN Subinterfaces

To configure SNMP Support for VLAN Subinterfaces, complete the tasks in the following section:

Enabling the SNMP Agent on VLAN Subinterfaces

Enabling the SNMP Agent on VLAN Subinterfaces

Perform the following task to enable the SNMP agent on VLAN subinterfaces.

SUMMARY STEPS

1. enable

2. configure terminal

3. snmp community public

4. interface type slot/port

5. encapsulation isl vlan-identifier

6. ip address ip-address mask

7. end

8. show vlans

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

snmp community string
Example:
Router(config)# snmp community public

Enables the SNMP agent for remote access.

Step 4 

interface type slot/port
Example:
Router(config)# interface FastEthernet 0/1.1

Selects a particular Fast Ethernet interface for configuration.

Step 5 

encapsulation isl vlan-identifier
Example:
Router(config-if)#  encapsulation isl 10

Enables the Inter-Switch Link.

Step 6 

ip address ip-address mask
Example:
Router(config)# ip address 192.168.10.1 
255.255.255.0

Sets a primary or secondary IP address for an interface.

Step 7 

end
Example:
Router(config-if)# end

Returns to privileged EXEC mode.

Step 8 

show vlans

Example:

Router# show vlans

Displays VLAN subinterfaces.

Configuration Examples for SNMP Support for VLAN Subinterfaces

Example: Enabling the SNMP Agent for VLAN Subinterfaces

Example: Enabling the SNMP Agent for VLAN Subinterfaces

The following configuration example shows you how to enable the SNMP agent on the router with VLAN subinterfaces to monitor the SNMP application remotely:

snmp community public
!
interface FastEthernet4/0.100
 encapsulation isl 100
 ip address 192.168.10.21 255.255.255.0
!
interface FastEthernet4/0.200
 encapsulation isl 200
 ip address 172.21.200.11 255.255.255.0
!
interface FastEthernet4/1.1
 encapsulation isl 10
 ip address 171.69.2.111 255.255.255.0

Additional References

Related Documents

Related Topic
Document Title

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

SNMP commands

Cisco IOS Network Management Command Reference


Standards

Standard
Title

None


MIBs

MIB
MIBs Link

None

To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFC
Title

RFC 1573

Evolution of the Interfaces Group of MIB-II


Technical Assistance

Description
Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html


Feature Information for SNMP Support for VLAN Subinterfaces

Table 1 lists the release history for this feature.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.


Table 1 Feature Information for SNMP Support for VLAN Subinterfaces 

Feature Name
Releases
Feature Information

SNMP Support for VLAN Subinterfaces

12.2

The SNMP Support for VLAN Subinterfaces feature provides mib-2 interfaces sparse table support for Fast Ethernet subinterfaces. This enhancement is similar to the functionality supported in Frame Relay subinterfaces.